arch/blackfin/include/asm/bfin_ppi.h - arm/linux-arm-legacy - Git at Google

 /*
  * bfin_ppi.h - interface to Blackfin PPIs
  *
  * Copyright 2005-2010 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
  */

 #ifndef __ASM_BFIN_PPI_H__
 #define __ASM_BFIN_PPI_H__

 #include <linux/types.h>
 #include <asm/blackfin.h>

 /*
  * All Blackfin system MMRs are padded to 32bits even if the register
  * itself is only 16bits.  So use a helper macro to streamline this.
  */
 #define __BFP(m) u16 m; u16 __pad_##m

 /*
  * bfin ppi registers layout
  */
 struct bfin_ppi_regs {
 	__BFP(control);
 	__BFP(status);
 	__BFP(count);
 	__BFP(delay);
 	__BFP(frame);
 };

 /*
  * bfin eppi registers layout
  */
 struct bfin_eppi_regs {
 	__BFP(status);
 	__BFP(hcount);
 	__BFP(hdelay);
 	__BFP(vcount);
 	__BFP(vdelay);
 	__BFP(frame);
 	__BFP(line);
 	__BFP(clkdiv);
 	u32 control;
 	u32 fs1w_hbl;
 	u32 fs1p_avpl;
 	u32 fs2w_lvb;
 	u32 fs2p_lavf;
 	u32 clip;
 };

 /*
  * bfin eppi3 registers layout
  */
 struct bfin_eppi3_regs {
 	u32 stat;
 	u32 hcnt;
 	u32 hdly;
 	u32 vcnt;
 	u32 vdly;
 	u32 frame;
 	u32 line;
 	u32 clkdiv;
 	u32 ctl;
 	u32 fs1_wlhb;
 	u32 fs1_paspl;
 	u32 fs2_wlvb;
 	u32 fs2_palpf;
 	u32 imsk;
 	u32 oddclip;
 	u32 evenclip;
 	u32 fs1_dly;
 	u32 fs2_dly;
 	u32 ctl2;
 };

 #undef __BFP

 #ifdef EPPI0_CTL2
 #define EPPI_STAT_CFIFOERR              0x00000001    /* Chroma FIFO Error */
 #define EPPI_STAT_YFIFOERR              0x00000002    /* Luma FIFO Error */
 #define EPPI_STAT_LTERROVR              0x00000004    /* Line Track Overflow */
 #define EPPI_STAT_LTERRUNDR             0x00000008    /* Line Track Underflow */
 #define EPPI_STAT_FTERROVR              0x00000010    /* Frame Track Overflow */
 #define EPPI_STAT_FTERRUNDR             0x00000020    /* Frame Track Underflow */
 #define EPPI_STAT_ERRNCOR               0x00000040    /* Preamble Error Not Corrected */
 #define EPPI_STAT_PXPERR                0x00000080    /* PxP Ready Error */
 #define EPPI_STAT_ERRDET                0x00004000    /* Preamble Error Detected */
 #define EPPI_STAT_FLD                   0x00008000    /* Current Field Received by EPPI */

 #define EPPI_HCNT_VALUE                 0x0000FFFF    /* Holds the number of samples to read in or write out per line, after PPIx_HDLY number of cycles have expired since the last assertion of PPIx_FS1 */

 #define EPPI_HDLY_VALUE                 0x0000FFFF    /* Number of PPIx_CLK cycles to delay after assertion of PPIx_FS1 before starting to read or write data */

 #define EPPI_VCNT_VALUE                 0x0000FFFF    /* Holds the number of lines to read in or write out, after PPIx_VDLY number of lines from the start of frame */

 #define EPPI_VDLY_VALUE                 0x0000FFFF    /* Number of lines to wait after the start of a new frame before starting to read/transmit data */

 #define EPPI_FRAME_VALUE                0x0000FFFF    /* Holds the number of lines expected per frame of data */

 #define EPPI_LINE_VALUE                 0x0000FFFF    /* Holds the number of samples expected per line */

 #define EPPI_CLKDIV_VALUE               0x0000FFFF    /* Internal clock divider */

 #define EPPI_CTL_EN                     0x00000001    /* PPI Enable */
 #define EPPI_CTL_DIR                    0x00000002    /* PPI Direction */
 #define EPPI_CTL_XFRTYPE                0x0000000C    /* PPI Operating Mode */
 #define EPPI_CTL_ACTIVE656              0x00000000    /* XFRTYPE: ITU656 Active Video Only Mode */
 #define EPPI_CTL_ENTIRE656              0x00000004    /* XFRTYPE: ITU656 Entire Field Mode */
 #define EPPI_CTL_VERT656                0x00000008    /* XFRTYPE: ITU656 Vertical Blanking Only Mode */
 #define EPPI_CTL_NON656                 0x0000000C    /* XFRTYPE: Non-ITU656 Mode (GP Mode) */
 #define EPPI_CTL_FSCFG                  0x00000030    /* Frame Sync Configuration */
 #define EPPI_CTL_SYNC0                  0x00000000    /* FSCFG: Sync Mode 0 */
 #define EPPI_CTL_SYNC1                  0x00000010    /* FSCFG: Sync Mode 1 */
 #define EPPI_CTL_SYNC2                  0x00000020    /* FSCFG: Sync Mode 2 */
 #define EPPI_CTL_SYNC3                  0x00000030    /* FSCFG: Sync Mode 3 */
 #define EPPI_CTL_FLDSEL                 0x00000040    /* Field Select/Trigger */
 #define EPPI_CTL_ITUTYPE                0x00000080    /* ITU Interlace or Progressive */
 #define EPPI_CTL_BLANKGEN               0x00000100    /* ITU Output Mode with Internal Blanking Generation */
 #define EPPI_CTL_ICLKGEN                0x00000200    /* Internal Clock Generation */
 #define EPPI_CTL_IFSGEN                 0x00000400    /* Internal Frame Sync Generation */
 #define EPPI_CTL_SIGNEXT                0x00000800    /* Sign Extension */
 #define EPPI_CTL_POLC                   0x00003000    /* Frame Sync and Data Driving and Sampling Edges */
 #define EPPI_CTL_POLC0                  0x00000000    /* POLC: Clock/Sync polarity mode 0 */
 #define EPPI_CTL_POLC1                  0x00001000    /* POLC: Clock/Sync polarity mode 1 */
 #define EPPI_CTL_POLC2                  0x00002000    /* POLC: Clock/Sync polarity mode 2 */
 #define EPPI_CTL_POLC3                  0x00003000    /* POLC: Clock/Sync polarity mode 3 */
 #define EPPI_CTL_POLS                   0x0000C000    /* Frame Sync Polarity */
 #define EPPI_CTL_FS1HI_FS2HI            0x00000000    /* POLS: FS1 and FS2 are active high */
 #define EPPI_CTL_FS1LO_FS2HI            0x00004000    /* POLS: FS1 is active low. FS2 is active high */
 #define EPPI_CTL_FS1HI_FS2LO            0x00008000    /* POLS: FS1 is active high. FS2 is active low */
 #define EPPI_CTL_FS1LO_FS2LO            0x0000C000    /* POLS: FS1 and FS2 are active low */
 #define EPPI_CTL_DLEN                   0x00070000    /* Data Length */
 #define EPPI_CTL_DLEN08                 0x00000000    /* DLEN: 8 bits */
 #define EPPI_CTL_DLEN10                 0x00010000    /* DLEN: 10 bits */
 #define EPPI_CTL_DLEN12                 0x00020000    /* DLEN: 12 bits */
 #define EPPI_CTL_DLEN14                 0x00030000    /* DLEN: 14 bits */
 #define EPPI_CTL_DLEN16                 0x00040000    /* DLEN: 16 bits */
 #define EPPI_CTL_DLEN18                 0x00050000    /* DLEN: 18 bits */
 #define EPPI_CTL_DLEN20                 0x00060000    /* DLEN: 20 bits */
 #define EPPI_CTL_DLEN24                 0x00070000    /* DLEN: 24 bits */
 #define EPPI_CTL_DMIRR                  0x00080000    /* Data Mirroring */
 #define EPPI_CTL_SKIPEN                 0x00100000    /* Skip Enable */
 #define EPPI_CTL_SKIPEO                 0x00200000    /* Skip Even or Odd */
 #define EPPI_CTL_PACKEN                 0x00400000    /* Pack/Unpack Enable */
 #define EPPI_CTL_SWAPEN                 0x00800000    /* Swap Enable */
 #define EPPI_CTL_SPLTEO                 0x01000000    /* Split Even and Odd Data Samples */
 #define EPPI_CTL_SUBSPLTODD             0x02000000    /* Sub-Split Odd Samples */
 #define EPPI_CTL_SPLTWRD                0x04000000    /* Split Word */
 #define EPPI_CTL_RGBFMTEN               0x08000000    /* RGB Formatting Enable */
 #define EPPI_CTL_DMACFG                 0x10000000    /* One or Two DMA Channels Mode */
 #define EPPI_CTL_DMAFINEN               0x20000000    /* DMA Finish Enable */
 #define EPPI_CTL_MUXSEL                 0x40000000    /* MUX Select */
 #define EPPI_CTL_CLKGATEN               0x80000000    /* Clock Gating Enable */

 #define EPPI_FS2_WLVB_F2VBAD            0xFF000000    /* In GP transmit mode with BLANKGEN = 1, contains number of lines of vertical blanking after field 2 */
 #define EPPI_FS2_WLVB_F2VBBD            0x00FF0000    /* In GP transmit mode with BLANKGEN = 1, contains number of lines of vertical blanking before field 2 */
 #define EPPI_FS2_WLVB_F1VBAD            0x0000FF00    /* In GP transmit mode with, BLANKGEN = 1, contains number of lines of vertical blanking after field 1 */
 #define EPPI_FS2_WLVB_F1VBBD            0x000000FF    /* In GP 2, or 3 FS modes used to generate PPIx_FS2 width (32-bit). In GP Transmit mode, with BLANKGEN=1, contains the number of lines of Vertical blanking before field 1. */

 #define EPPI_FS2_PALPF_F2ACT            0xFFFF0000    /* Number of lines of Active Data in Field 2 */
 #define EPPI_FS2_PALPF_F1ACT            0x0000FFFF    /* Number of lines of Active Data in Field 1 */

 #define EPPI_IMSK_CFIFOERR              0x00000001    /* Mask CFIFO Underflow or Overflow Error Interrupt */
 #define EPPI_IMSK_YFIFOERR              0x00000002    /* Mask YFIFO Underflow or Overflow Error Interrupt */
 #define EPPI_IMSK_LTERROVR              0x00000004    /* Mask Line Track Overflow Error Interrupt */
 #define EPPI_IMSK_LTERRUNDR             0x00000008    /* Mask Line Track Underflow Error Interrupt */
 #define EPPI_IMSK_FTERROVR              0x00000010    /* Mask Frame Track Overflow Error Interrupt */
 #define EPPI_IMSK_FTERRUNDR             0x00000020    /* Mask Frame Track Underflow Error Interrupt */
 #define EPPI_IMSK_ERRNCOR               0x00000040    /* Mask ITU Preamble Error Not Corrected Interrupt */
 #define EPPI_IMSK_PXPERR                0x00000080    /* Mask PxP Ready Error Interrupt */

 #define EPPI_ODDCLIP_HIGHODD            0xFFFF0000
 #define EPPI_ODDCLIP_LOWODD             0x0000FFFF

 #define EPPI_EVENCLIP_HIGHEVEN          0xFFFF0000
 #define EPPI_EVENCLIP_LOWEVEN           0x0000FFFF

 #define EPPI_CTL2_FS1FINEN              0x00000002    /* HSYNC Finish Enable */
 #endif
 #endif
	/*
	* bfin_ppi.h - interface to Blackfin PPIs
	*
	* Copyright 2005-2010 Analog Devices Inc.
	*
	* Licensed under the GPL-2 or later.
	*/

	#ifndef __ASM_BFIN_PPI_H__
	#define __ASM_BFIN_PPI_H__

	#include <linux/types.h>
	#include <asm/blackfin.h>

	/*
	* All Blackfin system MMRs are padded to 32bits even if the register
	* itself is only 16bits. So use a helper macro to streamline this.
	*/
	#define __BFP(m) u16 m; u16 __pad_##m

	/*
	* bfin ppi registers layout
	*/
	struct bfin_ppi_regs {
	__BFP(control);
	__BFP(status);
	__BFP(count);
	__BFP(delay);
	__BFP(frame);
	};

	/*
	* bfin eppi registers layout
	*/
	struct bfin_eppi_regs {
	__BFP(status);
	__BFP(hcount);
	__BFP(hdelay);
	__BFP(vcount);
	__BFP(vdelay);
	__BFP(frame);
	__BFP(line);
	__BFP(clkdiv);
	u32 control;
	u32 fs1w_hbl;
	u32 fs1p_avpl;
	u32 fs2w_lvb;
	u32 fs2p_lavf;
	u32 clip;
	};

	/*
	* bfin eppi3 registers layout
	*/
	struct bfin_eppi3_regs {
	u32 stat;
	u32 hcnt;
	u32 hdly;
	u32 vcnt;
	u32 vdly;
	u32 frame;
	u32 line;
	u32 clkdiv;
	u32 ctl;
	u32 fs1_wlhb;
	u32 fs1_paspl;
	u32 fs2_wlvb;
	u32 fs2_palpf;
	u32 imsk;
	u32 oddclip;
	u32 evenclip;
	u32 fs1_dly;
	u32 fs2_dly;
	u32 ctl2;
	};

	#undef __BFP

	#ifdef EPPI0_CTL2
	#define EPPI_STAT_CFIFOERR 0x00000001 /* Chroma FIFO Error */
	#define EPPI_STAT_YFIFOERR 0x00000002 /* Luma FIFO Error */
	#define EPPI_STAT_LTERROVR 0x00000004 /* Line Track Overflow */
	#define EPPI_STAT_LTERRUNDR 0x00000008 /* Line Track Underflow */
	#define EPPI_STAT_FTERROVR 0x00000010 /* Frame Track Overflow */
	#define EPPI_STAT_FTERRUNDR 0x00000020 /* Frame Track Underflow */
	#define EPPI_STAT_ERRNCOR 0x00000040 /* Preamble Error Not Corrected */
	#define EPPI_STAT_PXPERR 0x00000080 /* PxP Ready Error */
	#define EPPI_STAT_ERRDET 0x00004000 /* Preamble Error Detected */
	#define EPPI_STAT_FLD 0x00008000 /* Current Field Received by EPPI */

	#define EPPI_HCNT_VALUE 0x0000FFFF /* Holds the number of samples to read in or write out per line, after PPIx_HDLY number of cycles have expired since the last assertion of PPIx_FS1 */

	#define EPPI_HDLY_VALUE 0x0000FFFF /* Number of PPIx_CLK cycles to delay after assertion of PPIx_FS1 before starting to read or write data */

	#define EPPI_VCNT_VALUE 0x0000FFFF /* Holds the number of lines to read in or write out, after PPIx_VDLY number of lines from the start of frame */

	#define EPPI_VDLY_VALUE 0x0000FFFF /* Number of lines to wait after the start of a new frame before starting to read/transmit data */

	#define EPPI_FRAME_VALUE 0x0000FFFF /* Holds the number of lines expected per frame of data */

	#define EPPI_LINE_VALUE 0x0000FFFF /* Holds the number of samples expected per line */

	#define EPPI_CLKDIV_VALUE 0x0000FFFF /* Internal clock divider */

	#define EPPI_CTL_EN 0x00000001 /* PPI Enable */
	#define EPPI_CTL_DIR 0x00000002 /* PPI Direction */
	#define EPPI_CTL_XFRTYPE 0x0000000C /* PPI Operating Mode */
	#define EPPI_CTL_ACTIVE656 0x00000000 /* XFRTYPE: ITU656 Active Video Only Mode */
	#define EPPI_CTL_ENTIRE656 0x00000004 /* XFRTYPE: ITU656 Entire Field Mode */
	#define EPPI_CTL_VERT656 0x00000008 /* XFRTYPE: ITU656 Vertical Blanking Only Mode */
	#define EPPI_CTL_NON656 0x0000000C /* XFRTYPE: Non-ITU656 Mode (GP Mode) */
	#define EPPI_CTL_FSCFG 0x00000030 /* Frame Sync Configuration */
	#define EPPI_CTL_SYNC0 0x00000000 /* FSCFG: Sync Mode 0 */
	#define EPPI_CTL_SYNC1 0x00000010 /* FSCFG: Sync Mode 1 */
	#define EPPI_CTL_SYNC2 0x00000020 /* FSCFG: Sync Mode 2 */
	#define EPPI_CTL_SYNC3 0x00000030 /* FSCFG: Sync Mode 3 */
	#define EPPI_CTL_FLDSEL 0x00000040 /* Field Select/Trigger */
	#define EPPI_CTL_ITUTYPE 0x00000080 /* ITU Interlace or Progressive */
	#define EPPI_CTL_BLANKGEN 0x00000100 /* ITU Output Mode with Internal Blanking Generation */
	#define EPPI_CTL_ICLKGEN 0x00000200 /* Internal Clock Generation */
	#define EPPI_CTL_IFSGEN 0x00000400 /* Internal Frame Sync Generation */
	#define EPPI_CTL_SIGNEXT 0x00000800 /* Sign Extension */
	#define EPPI_CTL_POLC 0x00003000 /* Frame Sync and Data Driving and Sampling Edges */
	#define EPPI_CTL_POLC0 0x00000000 /* POLC: Clock/Sync polarity mode 0 */
	#define EPPI_CTL_POLC1 0x00001000 /* POLC: Clock/Sync polarity mode 1 */
	#define EPPI_CTL_POLC2 0x00002000 /* POLC: Clock/Sync polarity mode 2 */
	#define EPPI_CTL_POLC3 0x00003000 /* POLC: Clock/Sync polarity mode 3 */
	#define EPPI_CTL_POLS 0x0000C000 /* Frame Sync Polarity */
	#define EPPI_CTL_FS1HI_FS2HI 0x00000000 /* POLS: FS1 and FS2 are active high */
	#define EPPI_CTL_FS1LO_FS2HI 0x00004000 /* POLS: FS1 is active low. FS2 is active high */
	#define EPPI_CTL_FS1HI_FS2LO 0x00008000 /* POLS: FS1 is active high. FS2 is active low */
	#define EPPI_CTL_FS1LO_FS2LO 0x0000C000 /* POLS: FS1 and FS2 are active low */
	#define EPPI_CTL_DLEN 0x00070000 /* Data Length */
	#define EPPI_CTL_DLEN08 0x00000000 /* DLEN: 8 bits */
	#define EPPI_CTL_DLEN10 0x00010000 /* DLEN: 10 bits */
	#define EPPI_CTL_DLEN12 0x00020000 /* DLEN: 12 bits */
	#define EPPI_CTL_DLEN14 0x00030000 /* DLEN: 14 bits */
	#define EPPI_CTL_DLEN16 0x00040000 /* DLEN: 16 bits */
	#define EPPI_CTL_DLEN18 0x00050000 /* DLEN: 18 bits */
	#define EPPI_CTL_DLEN20 0x00060000 /* DLEN: 20 bits */
	#define EPPI_CTL_DLEN24 0x00070000 /* DLEN: 24 bits */
	#define EPPI_CTL_DMIRR 0x00080000 /* Data Mirroring */
	#define EPPI_CTL_SKIPEN 0x00100000 /* Skip Enable */
	#define EPPI_CTL_SKIPEO 0x00200000 /* Skip Even or Odd */
	#define EPPI_CTL_PACKEN 0x00400000 /* Pack/Unpack Enable */
	#define EPPI_CTL_SWAPEN 0x00800000 /* Swap Enable */
	#define EPPI_CTL_SPLTEO 0x01000000 /* Split Even and Odd Data Samples */
	#define EPPI_CTL_SUBSPLTODD 0x02000000 /* Sub-Split Odd Samples */
	#define EPPI_CTL_SPLTWRD 0x04000000 /* Split Word */
	#define EPPI_CTL_RGBFMTEN 0x08000000 /* RGB Formatting Enable */
	#define EPPI_CTL_DMACFG 0x10000000 /* One or Two DMA Channels Mode */
	#define EPPI_CTL_DMAFINEN 0x20000000 /* DMA Finish Enable */
	#define EPPI_CTL_MUXSEL 0x40000000 /* MUX Select */
	#define EPPI_CTL_CLKGATEN 0x80000000 /* Clock Gating Enable */

	#define EPPI_FS2_WLVB_F2VBAD 0xFF000000 /* In GP transmit mode with BLANKGEN = 1, contains number of lines of vertical blanking after field 2 */
	#define EPPI_FS2_WLVB_F2VBBD 0x00FF0000 /* In GP transmit mode with BLANKGEN = 1, contains number of lines of vertical blanking before field 2 */
	#define EPPI_FS2_WLVB_F1VBAD 0x0000FF00 /* In GP transmit mode with, BLANKGEN = 1, contains number of lines of vertical blanking after field 1 */
	#define EPPI_FS2_WLVB_F1VBBD 0x000000FF /* In GP 2, or 3 FS modes used to generate PPIx_FS2 width (32-bit). In GP Transmit mode, with BLANKGEN=1, contains the number of lines of Vertical blanking before field 1. */

	#define EPPI_FS2_PALPF_F2ACT 0xFFFF0000 /* Number of lines of Active Data in Field 2 */
	#define EPPI_FS2_PALPF_F1ACT 0x0000FFFF /* Number of lines of Active Data in Field 1 */

	#define EPPI_IMSK_CFIFOERR 0x00000001 /* Mask CFIFO Underflow or Overflow Error Interrupt */
	#define EPPI_IMSK_YFIFOERR 0x00000002 /* Mask YFIFO Underflow or Overflow Error Interrupt */
	#define EPPI_IMSK_LTERROVR 0x00000004 /* Mask Line Track Overflow Error Interrupt */
	#define EPPI_IMSK_LTERRUNDR 0x00000008 /* Mask Line Track Underflow Error Interrupt */
	#define EPPI_IMSK_FTERROVR 0x00000010 /* Mask Frame Track Overflow Error Interrupt */
	#define EPPI_IMSK_FTERRUNDR 0x00000020 /* Mask Frame Track Underflow Error Interrupt */
	#define EPPI_IMSK_ERRNCOR 0x00000040 /* Mask ITU Preamble Error Not Corrected Interrupt */
	#define EPPI_IMSK_PXPERR 0x00000080 /* Mask PxP Ready Error Interrupt */

	#define EPPI_ODDCLIP_HIGHODD 0xFFFF0000
	#define EPPI_ODDCLIP_LOWODD 0x0000FFFF

	#define EPPI_EVENCLIP_HIGHEVEN 0xFFFF0000
	#define EPPI_EVENCLIP_LOWEVEN 0x0000FFFF

	#define EPPI_CTL2_FS1FINEN 0x00000002 /* HSYNC Finish Enable */
	#endif
	#endif