Documentation: /proc/$pid/stat files
Documentation for the /proc/$pid/stat file.
Signed-off-by: Kees Cook <kees@outflux.net>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/Documentation/filesystems/proc.txt b/Documentation/filesystems/proc.txt
index 8756a07..460b892 100644
--- a/Documentation/filesystems/proc.txt
+++ b/Documentation/filesystems/proc.txt
@@ -171,7 +171,9 @@
This shows you nearly the same information you would get if you viewed it with
the ps command. In fact, ps uses the proc file system to obtain its
information. The statm file contains more detailed information about the
-process memory usage. Its seven fields are explained in Table 1-2.
+process memory usage. Its seven fields are explained in Table 1-2. The stat
+file contains details information about the process itself. Its fields are
+explained in Table 1-3.
Table 1-2: Contents of the statm files (as of 2.6.8-rc3)
@@ -188,16 +190,65 @@
dt number of dirty pages (always 0 on 2.6)
..............................................................................
+
+Table 1-3: Contents of the stat files (as of 2.6.22-rc3)
+..............................................................................
+ Field Content
+ pid process id
+ tcomm filename of the executable
+ state state (R is running, S is sleeping, D is sleeping in an
+ uninterruptible wait, Z is zombie, T is traced or stopped)
+ ppid process id of the parent process
+ pgrp pgrp of the process
+ sid session id
+ tty_nr tty the process uses
+ tty_pgrp pgrp of the tty
+ flags task flags
+ min_flt number of minor faults
+ cmin_flt number of minor faults with child's
+ maj_flt number of major faults
+ cmaj_flt number of major faults with child's
+ utime user mode jiffies
+ stime kernel mode jiffies
+ cutime user mode jiffies with child's
+ cstime kernel mode jiffies with child's
+ priority priority level
+ nice nice level
+ num_threads number of threads
+ start_time time the process started after system boot
+ vsize virtual memory size
+ rss resident set memory size
+ rsslim current limit in bytes on the rss
+ start_code address above which program text can run
+ end_code address below which program text can run
+ start_stack address of the start of the stack
+ esp current value of ESP
+ eip current value of EIP
+ pending bitmap of pending signals (obsolete)
+ blocked bitmap of blocked signals (obsolete)
+ sigign bitmap of ignored signals (obsolete)
+ sigcatch bitmap of catched signals (obsolete)
+ wchan address where process went to sleep
+ 0 (place holder)
+ 0 (place holder)
+ exit_signal signal to send to parent thread on exit
+ task_cpu which CPU the task is scheduled on
+ rt_priority realtime priority
+ policy scheduling policy (man sched_setscheduler)
+ blkio_ticks time spent waiting for block IO
+..............................................................................
+
+
1.2 Kernel data
---------------
Similar to the process entries, the kernel data files give information about
the running kernel. The files used to obtain this information are contained in
-/proc and are listed in Table 1-3. Not all of these will be present in your
+/proc and are listed in Table 1-4. Not all of these will be present in your
system. It depends on the kernel configuration and the loaded modules, which
files are there, and which are missing.
-Table 1-3: Kernel info in /proc
+Table 1-4: Kernel info in /proc
..............................................................................
File Content
apm Advanced power management info
@@ -473,10 +524,10 @@
More detailed information can be found in the controller specific
subdirectories. These are named ide0, ide1 and so on. Each of these
-directories contains the files shown in table 1-4.
+directories contains the files shown in table 1-5.
-Table 1-4: IDE controller info in /proc/ide/ide?
+Table 1-5: IDE controller info in /proc/ide/ide?
..............................................................................
File Content
channel IDE channel (0 or 1)
@@ -486,11 +537,11 @@
..............................................................................
Each device connected to a controller has a separate subdirectory in the
-controllers directory. The files listed in table 1-5 are contained in these
+controllers directory. The files listed in table 1-6 are contained in these
directories.
-Table 1-5: IDE device information
+Table 1-6: IDE device information
..............................................................................
File Content
cache The cache
