[HIFN]: Improve PLL initialization
The current PLL initalization has a number of deficiencies:
- uses fixed multiplier of 8, which overclocks the chip when using a
reference clock that operates at frequencies above 33MHz. According
to a comment in the BSD source, this is true for the external clock
on almost all every board.
- writes to a reserved bit
- doesn't follow the initialization procedure specified in chapter
6.11.1 of the HIFN hardware users guide
- doesn't allow to use the PCI clock
This patch adds a module parameter to specify the reference clock
(pci or external) and its frequency and uses that to calculate the
optimum multiplier to reach the maximal speed. By default it uses
the external clock and assumes a speed of 66MHz, which effectively
halfs the frequency currently used.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
diff --git a/drivers/crypto/hifn_795x.c b/drivers/crypto/hifn_795x.c
index bf817d4..de594bc 100644
--- a/drivers/crypto/hifn_795x.c
+++ b/drivers/crypto/hifn_795x.c
@@ -19,6 +19,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/moduleparam.h>
#include <linux/mod_devicetable.h>
#include <linux/interrupt.h>
#include <linux/pci.h>
@@ -47,6 +48,11 @@
#define dprintk(f, a...) do {} while (0)
#endif
+static char hifn_pll_ref[sizeof("extNNN")] = "ext";
+module_param_string(hifn_pll_ref, hifn_pll_ref, sizeof(hifn_pll_ref), 0444);
+MODULE_PARM_DESC(hifn_pll_ref,
+ "PLL reference clock (pci[freq] or ext[freq], default ext)");
+
static atomic_t hifn_dev_number;
#define ACRYPTO_OP_DECRYPT 0
@@ -286,7 +292,26 @@
#define HIFN_DMACNFG_DMARESET 0x00000002 /* DMA Reset # */
#define HIFN_DMACNFG_MSTRESET 0x00000001 /* Master Reset # */
-#define HIFN_PLL_7956 0x00001d18 /* 7956 PLL config value */
+/* PLL configuration register */
+#define HIFN_PLL_REF_CLK_HBI 0x00000000 /* HBI reference clock */
+#define HIFN_PLL_REF_CLK_PLL 0x00000001 /* PLL reference clock */
+#define HIFN_PLL_BP 0x00000002 /* Reference clock bypass */
+#define HIFN_PLL_PK_CLK_HBI 0x00000000 /* PK engine HBI clock */
+#define HIFN_PLL_PK_CLK_PLL 0x00000008 /* PK engine PLL clock */
+#define HIFN_PLL_PE_CLK_HBI 0x00000000 /* PE engine HBI clock */
+#define HIFN_PLL_PE_CLK_PLL 0x00000010 /* PE engine PLL clock */
+#define HIFN_PLL_RESERVED_1 0x00000400 /* Reserved bit, must be 1 */
+#define HIFN_PLL_ND_SHIFT 11 /* Clock multiplier shift */
+#define HIFN_PLL_ND_MULT_2 0x00000000 /* PLL clock multiplier 2 */
+#define HIFN_PLL_ND_MULT_4 0x00000800 /* PLL clock multiplier 4 */
+#define HIFN_PLL_ND_MULT_6 0x00001000 /* PLL clock multiplier 6 */
+#define HIFN_PLL_ND_MULT_8 0x00001800 /* PLL clock multiplier 8 */
+#define HIFN_PLL_ND_MULT_10 0x00002000 /* PLL clock multiplier 10 */
+#define HIFN_PLL_ND_MULT_12 0x00002800 /* PLL clock multiplier 12 */
+#define HIFN_PLL_IS_1_8 0x00000000 /* charge pump (mult. 1-8) */
+#define HIFN_PLL_IS_9_12 0x00010000 /* charge pump (mult. 9-12) */
+
+#define HIFN_PLL_FCK_MAX 266 /* Maximum PLL frequency */
/* Public key reset register (HIFN_1_PUB_RESET) */
#define HIFN_PUBRST_RESET 0x00000001 /* reset public/rng unit */
@@ -871,6 +896,64 @@
dma->cmdk = dma->srck = dma->dstk = dma->resk = 0;
}
+/*
+ * Initialize the PLL. We need to know the frequency of the reference clock
+ * to calculate the optimal multiplier. For PCI we assume 66MHz, since that
+ * allows us to operate without the risk of overclocking the chip. If it
+ * actually uses 33MHz, the chip will operate at half the speed, this can be
+ * overriden by specifying the frequency as module parameter (pci33).
+ *
+ * Unfortunately the PCI clock is not very suitable since the HIFN needs a
+ * stable clock and the PCI clock frequency may vary, so the default is the
+ * external clock. There is no way to find out its frequency, we default to
+ * 66MHz since according to Mike Ham of HiFn, almost every board in existence
+ * has an external crystal populated at 66MHz.
+ */
+static void hifn_init_pll(struct hifn_device *dev)
+{
+ unsigned int freq, m;
+ u32 pllcfg;
+
+ pllcfg = HIFN_1_PLL | HIFN_PLL_RESERVED_1;
+
+ if (strncmp(hifn_pll_ref, "ext", 3) == 0)
+ pllcfg |= HIFN_PLL_REF_CLK_PLL;
+ else
+ pllcfg |= HIFN_PLL_REF_CLK_HBI;
+
+ if (hifn_pll_ref[3] != '\0')
+ freq = simple_strtoul(hifn_pll_ref + 3, NULL, 10);
+ else {
+ freq = 66;
+ printk(KERN_INFO "hifn795x: assuming %uMHz clock speed, "
+ "override with hifn_pll_ref=%.3s<frequency>\n",
+ freq, hifn_pll_ref);
+ }
+
+ m = HIFN_PLL_FCK_MAX / freq;
+
+ pllcfg |= (m / 2 - 1) << HIFN_PLL_ND_SHIFT;
+ if (m <= 8)
+ pllcfg |= HIFN_PLL_IS_1_8;
+ else
+ pllcfg |= HIFN_PLL_IS_9_12;
+
+ /* Select clock source and enable clock bypass */
+ hifn_write_1(dev, HIFN_1_PLL, pllcfg |
+ HIFN_PLL_PK_CLK_HBI | HIFN_PLL_PE_CLK_HBI | HIFN_PLL_BP);
+
+ /* Let the chip lock to the input clock */
+ mdelay(10);
+
+ /* Disable clock bypass */
+ hifn_write_1(dev, HIFN_1_PLL, pllcfg |
+ HIFN_PLL_PK_CLK_HBI | HIFN_PLL_PE_CLK_HBI);
+
+ /* Switch the engines to the PLL */
+ hifn_write_1(dev, HIFN_1_PLL, pllcfg |
+ HIFN_PLL_PK_CLK_PLL | HIFN_PLL_PE_CLK_PLL);
+}
+
static void hifn_init_registers(struct hifn_device *dev)
{
u32 dptr = dev->desc_dma;
@@ -938,7 +1021,7 @@
#else
hifn_write_0(dev, HIFN_0_PUCNFG, 0x10342);
#endif
- hifn_write_1(dev, HIFN_1_PLL, HIFN_PLL_7956);
+ hifn_init_pll(dev);
hifn_write_0(dev, HIFN_0_PUISR, HIFN_PUISR_DSTOVER);
hifn_write_1(dev, HIFN_1_DMA_CNFG, HIFN_DMACNFG_MSTRESET |
@@ -2621,8 +2704,31 @@
static int __devinit hifn_init(void)
{
+ unsigned int freq;
int err;
+ if (strncmp(hifn_pll_ref, "ext", 3) &&
+ strncmp(hifn_pll_ref, "pci", 3)) {
+ printk(KERN_ERR "hifn795x: invalid hifn_pll_ref clock, "
+ "must be pci or ext");
+ return -EINVAL;
+ }
+
+ /*
+ * For the 7955/7956 the reference clock frequency must be in the
+ * range of 20MHz-100MHz. For the 7954 the upper bound is 66.67MHz,
+ * but this chip is currently not supported.
+ */
+ if (hifn_pll_ref[3] != '\0') {
+ freq = simple_strtoul(hifn_pll_ref + 3, NULL, 10);
+ if (freq < 20 || freq > 100) {
+ printk(KERN_ERR "hifn795x: invalid hifn_pll_ref "
+ "frequency, must be in the range "
+ "of 20-100");
+ return -EINVAL;
+ }
+ }
+
err = pci_register_driver(&hifn_pci_driver);
if (err < 0) {
dprintk("Failed to register PCI driver for %s device.\n",
