diff --git a/arch/arm/mach-sa1100/assabet.c b/arch/arm/mach-sa1100/assabet.c
index e2d411a..c3f5064 100644
--- a/arch/arm/mach-sa1100/assabet.c
+++ b/arch/arm/mach-sa1100/assabet.c
@@ -20,6 +20,8 @@
 #include <linux/delay.h>
 #include <linux/mm.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/irq.h>
@@ -69,33 +71,6 @@
 
 EXPORT_SYMBOL(ASSABET_BCR_frob);
 
-static void assabet_backlight_power(int on)
-{
-#ifndef ASSABET_PAL_VIDEO
-	if (on)
-		ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
-	else
-#endif
-		ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
-}
-
-/*
- * Turn on/off the backlight.  When turning the backlight on,
- * we wait 500us after turning it on so we don't cause the
- * supplies to droop when we enable the LCD controller (and
- * cause a hard reset.)
- */
-static void assabet_lcd_power(int on)
-{
-#ifndef ASSABET_PAL_VIDEO
-	if (on) {
-		ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
-		udelay(500);
-	} else
-#endif
-		ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
-}
-
 
 /*
  * Assabet flash support code.
@@ -197,6 +172,99 @@
 	.sclk_rate	= 11981000,
 };
 
+static void assabet_lcd_set_visual(u32 visual)
+{
+	u_int is_true_color = visual == FB_VISUAL_TRUECOLOR;
+
+	if (machine_is_assabet()) {
+#if 1		// phase 4 or newer Assabet's
+		if (is_true_color)
+			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+		else
+			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+#else
+		// older Assabet's
+		if (is_true_color)
+			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
+		else
+			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
+#endif
+	}
+}
+
+#ifndef ASSABET_PAL_VIDEO
+static void assabet_lcd_backlight_power(int on)
+{
+	if (on)
+		ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
+	else
+		ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+/*
+ * Turn on/off the backlight.  When turning the backlight on, we wait
+ * 500us after turning it on so we don't cause the supplies to droop
+ * when we enable the LCD controller (and cause a hard reset.)
+ */
+static void assabet_lcd_power(int on)
+{
+	if (on) {
+		ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
+		udelay(500);
+	} else
+		ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+/*
+ * The assabet uses a sharp LQ039Q2DS54 LCD module.  It is actually
+ * takes an RGB666 signal, but we provide it with an RGB565 signal
+ * instead (def_rgb_16).
+ */
+static struct sa1100fb_mach_info lq039q2ds54_info = {
+	.pixclock	= 171521,	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 5,		.vsync_len	= 1,
+	.left_margin	= 61,		.upper_margin	= 3,
+	.right_margin	= 9,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+	.backlight_power = assabet_lcd_backlight_power,
+	.lcd_power = assabet_lcd_power,
+	.set_visual = assabet_lcd_set_visual,
+};
+#else
+static void assabet_pal_backlight_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+static void assabet_pal_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+static struct sa1100fb_mach_info pal_info = {
+	.pixclock	= 67797,	.bpp		= 16,
+	.xres		= 640,		.yres		= 512,
+
+	.hsync_len	= 64,		.vsync_len	= 6,
+	.left_margin	= 125,		.upper_margin	= 70,
+	.right_margin	= 115,		.lower_margin	= 36,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+
+	.backlight_power = assabet_pal_backlight_power,
+	.lcd_power = assabet_pal_power,
+	.set_visual = assabet_lcd_set_visual,
+};
+#endif
+
 #ifdef CONFIG_ASSABET_NEPONSET
 static struct resource neponset_resources[] = {
 	DEFINE_RES_MEM(0x10000000, 0x08000000),
@@ -241,9 +309,6 @@
 	PPDR |= PPC_TXD3 | PPC_TXD1;
 	PPSR |= PPC_TXD3 | PPC_TXD1;
 
-	sa1100fb_lcd_power = assabet_lcd_power;
-	sa1100fb_backlight_power = assabet_backlight_power;
-
 	if (machine_has_neponset()) {
 		/*
 		 * Angel sets this, but other bootloaders may not.
@@ -262,6 +327,11 @@
 #endif
 	}
 
+#ifndef ASSABET_PAL_VIDEO
+	sa11x0_register_lcd(&lq039q2ds54_info);
+#else
+	sa11x0_register_lcd(&pal_video);
+#endif
 	sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
 			    ARRAY_SIZE(assabet_flash_resources));
 	sa11x0_register_irda(&assabet_irda_data);
diff --git a/arch/arm/mach-sa1100/collie.c b/arch/arm/mach-sa1100/collie.c
index dbe5cf7..841041e 100644
--- a/arch/arm/mach-sa1100/collie.c
+++ b/arch/arm/mach-sa1100/collie.c
@@ -28,6 +28,8 @@
 #include <linux/gpio.h>
 #include <linux/pda_power.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/irq.h>
@@ -294,6 +296,20 @@
 	DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M),
 };
 
+static struct sa1100fb_mach_info collie_lcd_info = {
+	.pixclock	= 171521,	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 5,		.vsync_len	= 1,
+	.left_margin	= 11,		.upper_margin	= 2,
+	.right_margin	= 30,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+};
+
 static void __init collie_init(void)
 {
 	int ret = 0;
@@ -332,6 +348,7 @@
 		printk(KERN_WARNING "collie: Unable to register LoCoMo device\n");
 	}
 
+	sa11x0_register_lcd(&collie_lcd_info);
 	sa11x0_register_mtd(&collie_flash_data, collie_flash_resources,
 			    ARRAY_SIZE(collie_flash_resources));
 	sa11x0_register_mcp(&collie_mcp_data);
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index 01a20ea..0296d69 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -20,6 +20,8 @@
 #include <linux/ioport.h>
 #include <linux/platform_device.h>
 
+#include <video/sa1100fb.h>
+
 #include <asm/div64.h>
 #include <mach/hardware.h>
 #include <asm/system.h>
@@ -247,6 +249,11 @@
 	.resource	= sa11x0fb_resources,
 };
 
+void sa11x0_register_lcd(struct sa1100fb_mach_info *inf)
+{
+	sa11x0_register_device(&sa11x0fb_device, inf);
+}
+
 static struct platform_device sa11x0pcmcia_device = {
 	.name		= "sa11x0-pcmcia",
 	.id		= -1,
@@ -319,7 +326,6 @@
 	&sa11x0uart3_device,
 	&sa11x0ssp_device,
 	&sa11x0pcmcia_device,
-	&sa11x0fb_device,
 	&sa11x0rtc_device,
 	&sa11x0dma_device,
 };
@@ -332,12 +338,6 @@
 
 arch_initcall(sa1100_init);
 
-void (*sa1100fb_backlight_power)(int on);
-void (*sa1100fb_lcd_power)(int on);
-
-EXPORT_SYMBOL(sa1100fb_backlight_power);
-EXPORT_SYMBOL(sa1100fb_lcd_power);
-
 
 /*
  * Common I/O mapping:
diff --git a/arch/arm/mach-sa1100/generic.h b/arch/arm/mach-sa1100/generic.h
index 33268cf..5c68be8 100644
--- a/arch/arm/mach-sa1100/generic.h
+++ b/arch/arm/mach-sa1100/generic.h
@@ -16,9 +16,6 @@
 	mi->bank[__nr].start = (__start), \
 	mi->bank[__nr].size = (__size)
 
-extern void (*sa1100fb_backlight_power)(int on);
-extern void (*sa1100fb_lcd_power)(int on);
-
 extern void sa1110_mb_enable(void);
 extern void sa1110_mb_disable(void);
 
@@ -40,3 +37,6 @@
 
 struct mcp_plat_data;
 void sa11x0_register_mcp(struct mcp_plat_data *data);
+
+struct sa1100fb_mach_info;
+void sa11x0_register_lcd(struct sa1100fb_mach_info *inf);
diff --git a/arch/arm/mach-sa1100/h3100.c b/arch/arm/mach-sa1100/h3100.c
index 1e6b3c1..f23e7d0 100644
--- a/arch/arm/mach-sa1100/h3100.c
+++ b/arch/arm/mach-sa1100/h3100.c
@@ -14,6 +14,8 @@
 #include <linux/kernel.h>
 #include <linux/gpio.h>
 
+#include <video/sa1100fb.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/irda.h>
@@ -36,13 +38,28 @@
 	}
 }
 
+static struct sa1100fb_mach_info h3100_lcd_info = {
+	.pixclock	= 406977, 	.bpp		= 4,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 26,		.vsync_len	= 41,
+	.left_margin	= 4,		.upper_margin	= 0,
+	.right_margin	= 4,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+	.cmap_greyscale	= 1,
+	.cmap_inverse	= 1,
+
+	.lccr0		= LCCR0_Mono | LCCR0_4PixMono | LCCR0_Sngl | LCCR0_Pas,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+	.lcd_power = h3100_lcd_power,
+};
 
 static void __init h3100_map_io(void)
 {
 	h3xxx_map_io();
 
-	sa1100fb_lcd_power = h3100_lcd_power;
-
 	/* Older bootldrs put GPIO2-9 in alternate mode on the
 	   assumption that they are used for video */
 	GAFR &= ~0x000001fb;
@@ -80,6 +97,8 @@
 {
 	h3xxx_init_gpio(h3100_default_gpio, ARRAY_SIZE(h3100_default_gpio));
 	h3xxx_mach_init();
+
+	sa11x0_register_lcd(&h3100_lcd_info);
 	sa11x0_register_irda(&h3100_irda_data);
 }
 
diff --git a/arch/arm/mach-sa1100/h3600.c b/arch/arm/mach-sa1100/h3600.c
index 6b58e74..2feac56 100644
--- a/arch/arm/mach-sa1100/h3600.c
+++ b/arch/arm/mach-sa1100/h3600.c
@@ -14,6 +14,8 @@
 #include <linux/kernel.h>
 #include <linux/gpio.h>
 
+#include <video/sa1100fb.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/irda.h>
@@ -56,11 +58,35 @@
 err1:	return;
 }
 
+static const struct sa1100fb_rgb h3600_rgb_16 = {
+	.red	= { .offset = 12, .length = 4, },
+	.green	= { .offset = 7,  .length = 4, },
+	.blue	= { .offset = 1,  .length = 4, },
+	.transp	= { .offset = 0,  .length = 0, },
+};
+
+static struct sa1100fb_mach_info h3600_lcd_info = {
+	.pixclock	= 174757, 	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 3,		.vsync_len	= 3,
+	.left_margin	= 12,		.upper_margin	= 10,
+	.right_margin	= 17,		.lower_margin	= 1,
+
+	.cmap_static	= 1,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+	.rgb[RGB_16] = &h3600_rgb_16,
+
+	.lcd_power = h3600_lcd_power,
+};
+
+
 static void __init h3600_map_io(void)
 {
 	h3xxx_map_io();
-
-	sa1100fb_lcd_power = h3600_lcd_power;
 }
 
 /*
@@ -121,6 +147,8 @@
 {
 	h3xxx_init_gpio(h3600_default_gpio, ARRAY_SIZE(h3600_default_gpio));
 	h3xxx_mach_init();
+
+	sa11x0_register_lcd(&h3600_lcd_info);
 	sa11x0_register_irda(&h3600_irda_data);
 }
 
diff --git a/arch/arm/mach-sa1100/include/mach/SA-1100.h b/arch/arm/mach-sa1100/include/mach/SA-1100.h
index 335a1ff..3f2d1b6 100644
--- a/arch/arm/mach-sa1100/include/mach/SA-1100.h
+++ b/arch/arm/mach-sa1100/include/mach/SA-1100.h
@@ -1688,16 +1688,6 @@
 #define LCD_Int100_0A	0xF     	/* LCD Intensity = 100.0% =  1     */
                 	        	/* (Alternative)                   */
 
-#define LCCR0		__REG(0xB0100000)  /* LCD Control Reg. 0 */
-#define LCSR		__REG(0xB0100004)  /* LCD Status Reg. */
-#define DBAR1		__REG(0xB0100010)  /* LCD DMA Base Address Reg. channel 1 */
-#define DCAR1		__REG(0xB0100014)  /* LCD DMA Current Address Reg. channel 1 */
-#define DBAR2		__REG(0xB0100018)  /* LCD DMA Base Address Reg.  channel 2 */
-#define DCAR2		__REG(0xB010001C)  /* LCD DMA Current Address Reg. channel 2 */
-#define LCCR1		__REG(0xB0100020)  /* LCD Control Reg. 1 */
-#define LCCR2		__REG(0xB0100024)  /* LCD Control Reg. 2 */
-#define LCCR3		__REG(0xB0100028)  /* LCD Control Reg. 3 */
-
 #define LCCR0_LEN	0x00000001	/* LCD ENable                      */
 #define LCCR0_CMS	0x00000002	/* Color/Monochrome display Select */
 #define LCCR0_Color	(LCCR0_CMS*0)	/*  Color display                  */
diff --git a/arch/arm/mach-sa1100/include/mach/shannon.h b/arch/arm/mach-sa1100/include/mach/shannon.h
index ec27d6e..a0d1114 100644
--- a/arch/arm/mach-sa1100/include/mach/shannon.h
+++ b/arch/arm/mach-sa1100/include/mach/shannon.h
@@ -21,7 +21,7 @@
 #define SHANNON_GPIO_U3_RTS		GPIO_GPIO (19)	/* ?? */
 #define SHANNON_GPIO_U3_CTS		GPIO_GPIO (20)	/* ?? */
 #define SHANNON_GPIO_SENSE_12V		GPIO_GPIO (21)	/* Input, 12v flash unprotect detected */
-#define SHANNON_GPIO_DISP_EN		GPIO_GPIO (22)	/* out */
+#define SHANNON_GPIO_DISP_EN		22		/* out */
 /* XXX GPIO 23 unaccounted for */
 #define SHANNON_GPIO_EJECT_0		GPIO_GPIO (24)	/* in */
 #define SHANNON_IRQ_GPIO_EJECT_0	IRQ_GPIO24
diff --git a/arch/arm/mach-sa1100/lart.c b/arch/arm/mach-sa1100/lart.c
index af4e276..463a322 100644
--- a/arch/arm/mach-sa1100/lart.c
+++ b/arch/arm/mach-sa1100/lart.c
@@ -6,6 +6,8 @@
 #include <linux/kernel.h>
 #include <linux/tty.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -26,8 +28,85 @@
 	.sclk_rate	= 11981000,
 };
 
+#ifdef LART_GREY_LCD
+static struct sa1100fb_mach_info lart_grey_info = {
+	.pixclock	= 150000,	.bpp		= 4,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 1,		.vsync_len	= 1,
+	.left_margin	= 4,		.upper_margin	= 0,
+	.right_margin	= 2,		.lower_margin	= 0,
+
+	.cmap_greyscale	= 1,
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Mono | LCCR0_Sngl | LCCR0_Pas | LCCR0_4PixMono,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+#ifdef LART_COLOR_LCD
+static struct sa1100fb_mach_info lart_color_info = {
+	.pixclock	= 150000,	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 2,		.vsync_len	= 3,
+	.left_margin	= 69,		.upper_margin	= 14,
+	.right_margin	= 8,		.lower_margin	= 4,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+#ifdef LART_VIDEO_OUT
+static struct sa1100fb_mach_info lart_video_info = {
+	.pixclock	= 39721,	.bpp		= 16,
+	.xres		= 640,		.yres		= 480,
+
+	.hsync_len	= 95,		.vsync_len	= 2,
+	.left_margin	= 40,		.upper_margin	= 32,
+	.right_margin	= 24,		.lower_margin	= 11,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnL | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
+};
+#endif
+
+#ifdef LART_KIT01_LCD
+static struct sa1100fb_mach_info lart_kit01_info = {
+	.pixclock	= 63291,	.bpp		= 16,
+	.xres		= 640,		.yres		= 480,
+
+	.hsync_len	= 64,		.vsync_len	= 3,
+	.left_margin	= 122,		.upper_margin	= 45,
+	.right_margin	= 10,		.lower_margin	= 10,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixFlEdg
+};
+#endif
+
 static void __init lart_init(void)
 {
+	struct sa1100fb_mach_info *inf = NULL;
+
+#ifdef LART_GREY_LCD
+	inf = &lart_grey_info;
+#endif
+#ifdef LART_COLOR_LCD
+	inf = &lart_color_info;
+#endif
+#ifdef LART_VIDEO_OUT
+	inf = &lart_video_info;
+#endif
+#ifdef LART_KIT01_LCD
+	inf = &lart_kit01_info;
+#endif
+
+	if (inf)
+		sa11x0_register_lcd(inf);
+
 	sa11x0_register_mcp(&lart_mcp_data);
 }
 
diff --git a/arch/arm/mach-sa1100/shannon.c b/arch/arm/mach-sa1100/shannon.c
index 5fd6156..77b2b9b 100644
--- a/arch/arm/mach-sa1100/shannon.c
+++ b/arch/arm/mach-sa1100/shannon.c
@@ -9,6 +9,8 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/setup.h>
@@ -54,8 +56,23 @@
 	.sclk_rate	= 11981000,
 };
 
+static struct sa1100fb_mach_info shannon_lcd_info = {
+	.pixclock	= 152500,	.bpp		= 8,
+	.xres		= 640,		.yres		= 480,
+
+	.hsync_len	= 4,		.vsync_len	= 3,
+	.left_margin	= 2,		.upper_margin	= 0,
+	.right_margin	= 1,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Dual | LCCR0_Pas,
+	.lccr3		= LCCR3_ACBsDiv(512),
+};
+
 static void __init shannon_init(void)
 {
+	sa11x0_register_lcd(&shannon_lcd_info);
 	sa11x0_register_mtd(&shannon_flash_data, &shannon_flash_resource, 1);
 	sa11x0_register_mcp(&shannon_mcp_data);
 }
diff --git a/drivers/video/sa1100fb.c b/drivers/video/sa1100fb.c
index 98d55d0..b632584 100644
--- a/drivers/video/sa1100fb.c
+++ b/drivers/video/sa1100fb.c
@@ -173,281 +173,47 @@
 #include <linux/init.h>
 #include <linux/ioport.h>
 #include <linux/cpufreq.h>
+#include <linux/gpio.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <linux/mutex.h>
 #include <linux/io.h>
 
+#include <video/sa1100fb.h>
+
 #include <mach/hardware.h>
 #include <asm/mach-types.h>
-#include <mach/assabet.h>
 #include <mach/shannon.h>
 
 /*
- * debugging?
- */
-#define DEBUG 0
-/*
  * Complain if VAR is out of range.
  */
 #define DEBUG_VAR 1
 
-#undef ASSABET_PAL_VIDEO
-
 #include "sa1100fb.h"
 
-extern void (*sa1100fb_backlight_power)(int on);
-extern void (*sa1100fb_lcd_power)(int on);
-
-static struct sa1100fb_rgb rgb_4 = {
+static const struct sa1100fb_rgb rgb_4 = {
 	.red	= { .offset = 0,  .length = 4, },
 	.green	= { .offset = 0,  .length = 4, },
 	.blue	= { .offset = 0,  .length = 4, },
 	.transp	= { .offset = 0,  .length = 0, },
 };
 
-static struct sa1100fb_rgb rgb_8 = {
+static const struct sa1100fb_rgb rgb_8 = {
 	.red	= { .offset = 0,  .length = 8, },
 	.green	= { .offset = 0,  .length = 8, },
 	.blue	= { .offset = 0,  .length = 8, },
 	.transp	= { .offset = 0,  .length = 0, },
 };
 
-static struct sa1100fb_rgb def_rgb_16 = {
+static const struct sa1100fb_rgb def_rgb_16 = {
 	.red	= { .offset = 11, .length = 5, },
 	.green	= { .offset = 5,  .length = 6, },
 	.blue	= { .offset = 0,  .length = 5, },
 	.transp	= { .offset = 0,  .length = 0, },
 };
 
-#ifdef CONFIG_SA1100_ASSABET
-#ifndef ASSABET_PAL_VIDEO
-/*
- * The assabet uses a sharp LQ039Q2DS54 LCD module.  It is actually
- * takes an RGB666 signal, but we provide it with an RGB565 signal
- * instead (def_rgb_16).
- */
-static struct sa1100fb_mach_info lq039q2ds54_info __initdata = {
-	.pixclock	= 171521,	.bpp		= 16,
-	.xres		= 320,		.yres		= 240,
 
-	.hsync_len	= 5,		.vsync_len	= 1,
-	.left_margin	= 61,		.upper_margin	= 3,
-	.right_margin	= 9,		.lower_margin	= 0,
-
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
-};
-#else
-static struct sa1100fb_mach_info pal_info __initdata = {
-	.pixclock	= 67797,	.bpp		= 16,
-	.xres		= 640,		.yres		= 512,
-
-	.hsync_len	= 64,		.vsync_len	= 6,
-	.left_margin	= 125,		.upper_margin	= 70,
-	.right_margin	= 115,		.lower_margin	= 36,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-#endif
-
-#ifdef CONFIG_SA1100_H3600
-static struct sa1100fb_mach_info h3600_info __initdata = {
-	.pixclock	= 174757, 	.bpp		= 16,
-	.xres		= 320,		.yres		= 240,
-
-	.hsync_len	= 3,		.vsync_len	= 3,
-	.left_margin	= 12,		.upper_margin	= 10,
-	.right_margin	= 17,		.lower_margin	= 1,
-
-	.cmap_static	= 1,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
-};
-
-static struct sa1100fb_rgb h3600_rgb_16 = {
-	.red	= { .offset = 12, .length = 4, },
-	.green	= { .offset = 7,  .length = 4, },
-	.blue	= { .offset = 1,  .length = 4, },
-	.transp	= { .offset = 0,  .length = 0, },
-};
-#endif
-
-#ifdef CONFIG_SA1100_H3100
-static struct sa1100fb_mach_info h3100_info __initdata = {
-	.pixclock	= 406977, 	.bpp		= 4,
-	.xres		= 320,		.yres		= 240,
-
-	.hsync_len	= 26,		.vsync_len	= 41,
-	.left_margin	= 4,		.upper_margin	= 0,
-	.right_margin	= 4,		.lower_margin	= 0,
-
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-	.cmap_greyscale	= 1,
-	.cmap_inverse	= 1,
-
-	.lccr0		= LCCR0_Mono | LCCR0_4PixMono | LCCR0_Sngl | LCCR0_Pas,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
-};
-#endif
-
-#ifdef CONFIG_SA1100_COLLIE
-static struct sa1100fb_mach_info collie_info __initdata = {
-	.pixclock	= 171521,	.bpp		= 16,
-	.xres		= 320,		.yres		= 240,
-
-	.hsync_len	= 5,		.vsync_len	= 1,
-	.left_margin	= 11,		.upper_margin	= 2,
-	.right_margin	= 30,		.lower_margin	= 0,
-
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
-};
-#endif
-
-#ifdef LART_GREY_LCD
-static struct sa1100fb_mach_info lart_grey_info __initdata = {
-	.pixclock	= 150000,	.bpp		= 4,
-	.xres		= 320,		.yres		= 240,
-
-	.hsync_len	= 1,		.vsync_len	= 1,
-	.left_margin	= 4,		.upper_margin	= 0,
-	.right_margin	= 2,		.lower_margin	= 0,
-
-	.cmap_greyscale	= 1,
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
-	.lccr0		= LCCR0_Mono | LCCR0_Sngl | LCCR0_Pas | LCCR0_4PixMono,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-#ifdef LART_COLOR_LCD
-static struct sa1100fb_mach_info lart_color_info __initdata = {
-	.pixclock	= 150000,	.bpp		= 16,
-	.xres		= 320,		.yres		= 240,
-
-	.hsync_len	= 2,		.vsync_len	= 3,
-	.left_margin	= 69,		.upper_margin	= 14,
-	.right_margin	= 8,		.lower_margin	= 4,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-#ifdef LART_VIDEO_OUT
-static struct sa1100fb_mach_info lart_video_info __initdata = {
-	.pixclock	= 39721,	.bpp		= 16,
-	.xres		= 640,		.yres		= 480,
-
-	.hsync_len	= 95,		.vsync_len	= 2,
-	.left_margin	= 40,		.upper_margin	= 32,
-	.right_margin	= 24,		.lower_margin	= 11,
-
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnL | LCCR3_PixFlEdg | LCCR3_ACBsDiv(512),
-};
-#endif
-
-#ifdef LART_KIT01_LCD
-static struct sa1100fb_mach_info lart_kit01_info __initdata = {
-	.pixclock	= 63291,	.bpp		= 16,
-	.xres		= 640,		.yres		= 480,
-
-	.hsync_len	= 64,		.vsync_len	= 3,
-	.left_margin	= 122,		.upper_margin	= 45,
-	.right_margin	= 10,		.lower_margin	= 10,
-
-	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
-	.lccr3		= LCCR3_OutEnH | LCCR3_PixFlEdg
-};
-#endif
-
-#ifdef CONFIG_SA1100_SHANNON
-static struct sa1100fb_mach_info shannon_info __initdata = {
-	.pixclock	= 152500,	.bpp		= 8,
-	.xres		= 640,		.yres		= 480,
-
-	.hsync_len	= 4,		.vsync_len	= 3,
-	.left_margin	= 2,		.upper_margin	= 0,
-	.right_margin	= 1,		.lower_margin	= 0,
-
-	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-
-	.lccr0		= LCCR0_Color | LCCR0_Dual | LCCR0_Pas,
-	.lccr3		= LCCR3_ACBsDiv(512),
-};
-#endif
-
-
-
-static struct sa1100fb_mach_info * __init
-sa1100fb_get_machine_info(struct sa1100fb_info *fbi)
-{
-	struct sa1100fb_mach_info *inf = NULL;
-
-	/*
-	 *            R        G       B       T
-	 * default  {11,5}, { 5,6}, { 0,5}, { 0,0}
-	 * h3600    {12,4}, { 7,4}, { 1,4}, { 0,0}
-	 * freebird { 8,4}, { 4,4}, { 0,4}, {12,4}
-	 */
-#ifdef CONFIG_SA1100_ASSABET
-	if (machine_is_assabet()) {
-#ifndef ASSABET_PAL_VIDEO
-		inf = &lq039q2ds54_info;
-#else
-		inf = &pal_info;
-#endif
-	}
-#endif
-#ifdef CONFIG_SA1100_H3100
-	if (machine_is_h3100()) {
-		inf = &h3100_info;
-	}
-#endif
-#ifdef CONFIG_SA1100_H3600
-	if (machine_is_h3600()) {
-		inf = &h3600_info;
-		fbi->rgb[RGB_16] = &h3600_rgb_16;
-	}
-#endif
-#ifdef CONFIG_SA1100_COLLIE
-	if (machine_is_collie()) {
-		inf = &collie_info;
-	}
-#endif
-#ifdef CONFIG_SA1100_LART
-	if (machine_is_lart()) {
-#ifdef LART_GREY_LCD
-		inf = &lart_grey_info;
-#endif
-#ifdef LART_COLOR_LCD
-		inf = &lart_color_info;
-#endif
-#ifdef LART_VIDEO_OUT
-		inf = &lart_video_info;
-#endif
-#ifdef LART_KIT01_LCD
-		inf = &lart_kit01_info;
-#endif
-	}
-#endif
-#ifdef CONFIG_SA1100_SHANNON
-	if (machine_is_shannon()) {
-		inf = &shannon_info;
-	}
-#endif
-	return inf;
-}
 
 static int sa1100fb_activate_var(struct fb_var_screeninfo *var, struct sa1100fb_info *);
 static void set_ctrlr_state(struct sa1100fb_info *fbi, u_int state);
@@ -533,7 +299,7 @@
 	 * is what you poke into the framebuffer to produce the
 	 * colour you requested.
 	 */
-	if (fbi->cmap_inverse) {
+	if (fbi->inf->cmap_inverse) {
 		red   = 0xffff - red;
 		green = 0xffff - green;
 		blue  = 0xffff - blue;
@@ -607,14 +373,14 @@
 		var->xres = MIN_XRES;
 	if (var->yres < MIN_YRES)
 		var->yres = MIN_YRES;
-	if (var->xres > fbi->max_xres)
-		var->xres = fbi->max_xres;
-	if (var->yres > fbi->max_yres)
-		var->yres = fbi->max_yres;
+	if (var->xres > fbi->inf->xres)
+		var->xres = fbi->inf->xres;
+	if (var->yres > fbi->inf->yres)
+		var->yres = fbi->inf->yres;
 	var->xres_virtual = max(var->xres_virtual, var->xres);
 	var->yres_virtual = max(var->yres_virtual, var->yres);
 
-	DPRINTK("var->bits_per_pixel=%d\n", var->bits_per_pixel);
+	dev_dbg(fbi->dev, "var->bits_per_pixel=%d\n", var->bits_per_pixel);
 	switch (var->bits_per_pixel) {
 	case 4:
 		rgbidx = RGB_4;
@@ -638,16 +404,16 @@
 	var->blue   = fbi->rgb[rgbidx]->blue;
 	var->transp = fbi->rgb[rgbidx]->transp;
 
-	DPRINTK("RGBT length = %d:%d:%d:%d\n",
+	dev_dbg(fbi->dev, "RGBT length = %d:%d:%d:%d\n",
 		var->red.length, var->green.length, var->blue.length,
 		var->transp.length);
 
-	DPRINTK("RGBT offset = %d:%d:%d:%d\n",
+	dev_dbg(fbi->dev, "RGBT offset = %d:%d:%d:%d\n",
 		var->red.offset, var->green.offset, var->blue.offset,
 		var->transp.offset);
 
 #ifdef CONFIG_CPU_FREQ
-	printk(KERN_DEBUG "dma period = %d ps, clock = %d kHz\n",
+	dev_dbg(fbi->dev, "dma period = %d ps, clock = %d kHz\n",
 		sa1100fb_display_dma_period(var),
 		cpufreq_get(smp_processor_id()));
 #endif
@@ -655,22 +421,10 @@
 	return 0;
 }
 
-static inline void sa1100fb_set_truecolor(u_int is_true_color)
+static void sa1100fb_set_visual(struct sa1100fb_info *fbi, u32 visual)
 {
-	if (machine_is_assabet()) {
-#if 1		// phase 4 or newer Assabet's
-		if (is_true_color)
-			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
-		else
-			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
-#else
-		// older Assabet's
-		if (is_true_color)
-			ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB);
-		else
-			ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB);
-#endif
-	}
+	if (fbi->inf->set_visual)
+		fbi->inf->set_visual(visual);
 }
 
 /*
@@ -683,11 +437,11 @@
 	struct fb_var_screeninfo *var = &info->var;
 	unsigned long palette_mem_size;
 
-	DPRINTK("set_par\n");
+	dev_dbg(fbi->dev, "set_par\n");
 
 	if (var->bits_per_pixel == 16)
 		fbi->fb.fix.visual = FB_VISUAL_TRUECOLOR;
-	else if (!fbi->cmap_static)
+	else if (!fbi->inf->cmap_static)
 		fbi->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR;
 	else {
 		/*
@@ -704,7 +458,7 @@
 
 	palette_mem_size = fbi->palette_size * sizeof(u16);
 
-	DPRINTK("palette_mem_size = 0x%08lx\n", (u_long) palette_mem_size);
+	dev_dbg(fbi->dev, "palette_mem_size = 0x%08lx\n", palette_mem_size);
 
 	fbi->palette_cpu = (u16 *)(fbi->map_cpu + PAGE_SIZE - palette_mem_size);
 	fbi->palette_dma = fbi->map_dma + PAGE_SIZE - palette_mem_size;
@@ -712,7 +466,7 @@
 	/*
 	 * Set (any) board control register to handle new color depth
 	 */
-	sa1100fb_set_truecolor(fbi->fb.fix.visual == FB_VISUAL_TRUECOLOR);
+	sa1100fb_set_visual(fbi, fbi->fb.fix.visual);
 	sa1100fb_activate_var(var, fbi);
 
 	return 0;
@@ -728,7 +482,7 @@
 	/*
 	 * Make sure the user isn't doing something stupid.
 	 */
-	if (!kspc && (fbi->fb.var.bits_per_pixel == 16 || fbi->cmap_static))
+	if (!kspc && (fbi->fb.var.bits_per_pixel == 16 || fbi->inf->cmap_static))
 		return -EINVAL;
 
 	return gen_set_cmap(cmap, kspc, con, info);
@@ -775,7 +529,7 @@
 	struct sa1100fb_info *fbi = (struct sa1100fb_info *)info;
 	int i;
 
-	DPRINTK("sa1100fb_blank: blank=%d\n", blank);
+	dev_dbg(fbi->dev, "sa1100fb_blank: blank=%d\n", blank);
 
 	switch (blank) {
 	case FB_BLANK_POWERDOWN:
@@ -863,43 +617,43 @@
 	u_int half_screen_size, yres, pcd;
 	u_long flags;
 
-	DPRINTK("Configuring SA1100 LCD\n");
+	dev_dbg(fbi->dev, "Configuring SA1100 LCD\n");
 
-	DPRINTK("var: xres=%d hslen=%d lm=%d rm=%d\n",
+	dev_dbg(fbi->dev, "var: xres=%d hslen=%d lm=%d rm=%d\n",
 		var->xres, var->hsync_len,
 		var->left_margin, var->right_margin);
-	DPRINTK("var: yres=%d vslen=%d um=%d bm=%d\n",
+	dev_dbg(fbi->dev, "var: yres=%d vslen=%d um=%d bm=%d\n",
 		var->yres, var->vsync_len,
 		var->upper_margin, var->lower_margin);
 
 #if DEBUG_VAR
 	if (var->xres < 16        || var->xres > 1024)
-		printk(KERN_ERR "%s: invalid xres %d\n",
+		dev_err(fbi->dev, "%s: invalid xres %d\n",
 			fbi->fb.fix.id, var->xres);
 	if (var->hsync_len < 1    || var->hsync_len > 64)
-		printk(KERN_ERR "%s: invalid hsync_len %d\n",
+		dev_err(fbi->dev, "%s: invalid hsync_len %d\n",
 			fbi->fb.fix.id, var->hsync_len);
 	if (var->left_margin < 1  || var->left_margin > 255)
-		printk(KERN_ERR "%s: invalid left_margin %d\n",
+		dev_err(fbi->dev, "%s: invalid left_margin %d\n",
 			fbi->fb.fix.id, var->left_margin);
 	if (var->right_margin < 1 || var->right_margin > 255)
-		printk(KERN_ERR "%s: invalid right_margin %d\n",
+		dev_err(fbi->dev, "%s: invalid right_margin %d\n",
 			fbi->fb.fix.id, var->right_margin);
 	if (var->yres < 1         || var->yres > 1024)
-		printk(KERN_ERR "%s: invalid yres %d\n",
+		dev_err(fbi->dev, "%s: invalid yres %d\n",
 			fbi->fb.fix.id, var->yres);
 	if (var->vsync_len < 1    || var->vsync_len > 64)
-		printk(KERN_ERR "%s: invalid vsync_len %d\n",
+		dev_err(fbi->dev, "%s: invalid vsync_len %d\n",
 			fbi->fb.fix.id, var->vsync_len);
 	if (var->upper_margin < 0 || var->upper_margin > 255)
-		printk(KERN_ERR "%s: invalid upper_margin %d\n",
+		dev_err(fbi->dev, "%s: invalid upper_margin %d\n",
 			fbi->fb.fix.id, var->upper_margin);
 	if (var->lower_margin < 0 || var->lower_margin > 255)
-		printk(KERN_ERR "%s: invalid lower_margin %d\n",
+		dev_err(fbi->dev, "%s: invalid lower_margin %d\n",
 			fbi->fb.fix.id, var->lower_margin);
 #endif
 
-	new_regs.lccr0 = fbi->lccr0 |
+	new_regs.lccr0 = fbi->inf->lccr0 |
 		LCCR0_LEN | LCCR0_LDM | LCCR0_BAM |
 		LCCR0_ERM | LCCR0_LtlEnd | LCCR0_DMADel(0);
 
@@ -914,7 +668,7 @@
 	 * the YRES parameter.
 	 */
 	yres = var->yres;
-	if (fbi->lccr0 & LCCR0_Dual)
+	if (fbi->inf->lccr0 & LCCR0_Dual)
 		yres /= 2;
 
 	new_regs.lccr2 =
@@ -924,14 +678,14 @@
 		LCCR2_EndFrmDel(var->lower_margin);
 
 	pcd = get_pcd(var->pixclock, cpufreq_get(0));
-	new_regs.lccr3 = LCCR3_PixClkDiv(pcd) | fbi->lccr3 |
+	new_regs.lccr3 = LCCR3_PixClkDiv(pcd) | fbi->inf->lccr3 |
 		(var->sync & FB_SYNC_HOR_HIGH_ACT ? LCCR3_HorSnchH : LCCR3_HorSnchL) |
 		(var->sync & FB_SYNC_VERT_HIGH_ACT ? LCCR3_VrtSnchH : LCCR3_VrtSnchL);
 
-	DPRINTK("nlccr0 = 0x%08lx\n", new_regs.lccr0);
-	DPRINTK("nlccr1 = 0x%08lx\n", new_regs.lccr1);
-	DPRINTK("nlccr2 = 0x%08lx\n", new_regs.lccr2);
-	DPRINTK("nlccr3 = 0x%08lx\n", new_regs.lccr3);
+	dev_dbg(fbi->dev, "nlccr0 = 0x%08lx\n", new_regs.lccr0);
+	dev_dbg(fbi->dev, "nlccr1 = 0x%08lx\n", new_regs.lccr1);
+	dev_dbg(fbi->dev, "nlccr2 = 0x%08lx\n", new_regs.lccr2);
+	dev_dbg(fbi->dev, "nlccr3 = 0x%08lx\n", new_regs.lccr3);
 
 	half_screen_size = var->bits_per_pixel;
 	half_screen_size = half_screen_size * var->xres * var->yres / 16;
@@ -951,9 +705,12 @@
 	 * Only update the registers if the controller is enabled
 	 * and something has changed.
 	 */
-	if ((LCCR0 != fbi->reg_lccr0)       || (LCCR1 != fbi->reg_lccr1) ||
-	    (LCCR2 != fbi->reg_lccr2)       || (LCCR3 != fbi->reg_lccr3) ||
-	    (DBAR1 != fbi->dbar1) || (DBAR2 != fbi->dbar2))
+	if (readl_relaxed(fbi->base + LCCR0) != fbi->reg_lccr0 ||
+	    readl_relaxed(fbi->base + LCCR1) != fbi->reg_lccr1 ||
+	    readl_relaxed(fbi->base + LCCR2) != fbi->reg_lccr2 ||
+	    readl_relaxed(fbi->base + LCCR3) != fbi->reg_lccr3 ||
+	    readl_relaxed(fbi->base + DBAR1) != fbi->dbar1 ||
+	    readl_relaxed(fbi->base + DBAR2) != fbi->dbar2)
 		sa1100fb_schedule_work(fbi, C_REENABLE);
 
 	return 0;
@@ -967,18 +724,18 @@
  */
 static inline void __sa1100fb_backlight_power(struct sa1100fb_info *fbi, int on)
 {
-	DPRINTK("backlight o%s\n", on ? "n" : "ff");
+	dev_dbg(fbi->dev, "backlight o%s\n", on ? "n" : "ff");
 
-	if (sa1100fb_backlight_power)
-		sa1100fb_backlight_power(on);
+	if (fbi->inf->backlight_power)
+		fbi->inf->backlight_power(on);
 }
 
 static inline void __sa1100fb_lcd_power(struct sa1100fb_info *fbi, int on)
 {
-	DPRINTK("LCD power o%s\n", on ? "n" : "ff");
+	dev_dbg(fbi->dev, "LCD power o%s\n", on ? "n" : "ff");
 
-	if (sa1100fb_lcd_power)
-		sa1100fb_lcd_power(on);
+	if (fbi->inf->lcd_power)
+		fbi->inf->lcd_power(on);
 }
 
 static void sa1100fb_setup_gpio(struct sa1100fb_info *fbi)
@@ -1008,14 +765,25 @@
 	}
 
 	if (mask) {
+		unsigned long flags;
+
+		/*
+		 * SA-1100 requires the GPIO direction register set
+		 * appropriately for the alternate function.  Hence
+		 * we set it here via bitmask rather than excessive
+		 * fiddling via the GPIO subsystem - and even then
+		 * we'll still have to deal with GAFR.
+		 */
+		local_irq_save(flags);
 		GPDR |= mask;
 		GAFR |= mask;
+		local_irq_restore(flags);
 	}
 }
 
 static void sa1100fb_enable_controller(struct sa1100fb_info *fbi)
 {
-	DPRINTK("Enabling LCD controller\n");
+	dev_dbg(fbi->dev, "Enabling LCD controller\n");
 
 	/*
 	 * Make sure the mode bits are present in the first palette entry
@@ -1024,43 +792,46 @@
 	fbi->palette_cpu[0] |= palette_pbs(&fbi->fb.var);
 
 	/* Sequence from 11.7.10 */
-	LCCR3 = fbi->reg_lccr3;
-	LCCR2 = fbi->reg_lccr2;
-	LCCR1 = fbi->reg_lccr1;
-	LCCR0 = fbi->reg_lccr0 & ~LCCR0_LEN;
-	DBAR1 = fbi->dbar1;
-	DBAR2 = fbi->dbar2;
-	LCCR0 |= LCCR0_LEN;
+	writel_relaxed(fbi->reg_lccr3, fbi->base + LCCR3);
+	writel_relaxed(fbi->reg_lccr2, fbi->base + LCCR2);
+	writel_relaxed(fbi->reg_lccr1, fbi->base + LCCR1);
+	writel_relaxed(fbi->reg_lccr0 & ~LCCR0_LEN, fbi->base + LCCR0);
+	writel_relaxed(fbi->dbar1, fbi->base + DBAR1);
+	writel_relaxed(fbi->dbar2, fbi->base + DBAR2);
+	writel_relaxed(fbi->reg_lccr0 | LCCR0_LEN, fbi->base + LCCR0);
 
-	if (machine_is_shannon()) {
-		GPDR |= SHANNON_GPIO_DISP_EN;
-		GPSR |= SHANNON_GPIO_DISP_EN;
-	}
+	if (machine_is_shannon())
+		gpio_set_value(SHANNON_GPIO_DISP_EN, 1);
 
-	DPRINTK("DBAR1 = 0x%08x\n", DBAR1);
-	DPRINTK("DBAR2 = 0x%08x\n", DBAR2);
-	DPRINTK("LCCR0 = 0x%08x\n", LCCR0);
-	DPRINTK("LCCR1 = 0x%08x\n", LCCR1);
-	DPRINTK("LCCR2 = 0x%08x\n", LCCR2);
-	DPRINTK("LCCR3 = 0x%08x\n", LCCR3);
+	dev_dbg(fbi->dev, "DBAR1: 0x%08x\n", readl_relaxed(fbi->base + DBAR1));
+	dev_dbg(fbi->dev, "DBAR2: 0x%08x\n", readl_relaxed(fbi->base + DBAR2));
+	dev_dbg(fbi->dev, "LCCR0: 0x%08x\n", readl_relaxed(fbi->base + LCCR0));
+	dev_dbg(fbi->dev, "LCCR1: 0x%08x\n", readl_relaxed(fbi->base + LCCR1));
+	dev_dbg(fbi->dev, "LCCR2: 0x%08x\n", readl_relaxed(fbi->base + LCCR2));
+	dev_dbg(fbi->dev, "LCCR3: 0x%08x\n", readl_relaxed(fbi->base + LCCR3));
 }
 
 static void sa1100fb_disable_controller(struct sa1100fb_info *fbi)
 {
 	DECLARE_WAITQUEUE(wait, current);
+	u32 lccr0;
 
-	DPRINTK("Disabling LCD controller\n");
+	dev_dbg(fbi->dev, "Disabling LCD controller\n");
 
-	if (machine_is_shannon()) {
-		GPCR |= SHANNON_GPIO_DISP_EN;
-	}	
+	if (machine_is_shannon())
+		gpio_set_value(SHANNON_GPIO_DISP_EN, 0);
 
 	set_current_state(TASK_UNINTERRUPTIBLE);
 	add_wait_queue(&fbi->ctrlr_wait, &wait);
 
-	LCSR = 0xffffffff;	/* Clear LCD Status Register */
-	LCCR0 &= ~LCCR0_LDM;	/* Enable LCD Disable Done Interrupt */
-	LCCR0 &= ~LCCR0_LEN;	/* Disable LCD Controller */
+	/* Clear LCD Status Register */
+	writel_relaxed(~0, fbi->base + LCSR);
+
+	lccr0 = readl_relaxed(fbi->base + LCCR0);
+	lccr0 &= ~LCCR0_LDM;	/* Enable LCD Disable Done Interrupt */
+	writel_relaxed(lccr0, fbi->base + LCCR0);
+	lccr0 &= ~LCCR0_LEN;	/* Disable LCD Controller */
+	writel_relaxed(lccr0, fbi->base + LCCR0);
 
 	schedule_timeout(20 * HZ / 1000);
 	remove_wait_queue(&fbi->ctrlr_wait, &wait);
@@ -1072,14 +843,15 @@
 static irqreturn_t sa1100fb_handle_irq(int irq, void *dev_id)
 {
 	struct sa1100fb_info *fbi = dev_id;
-	unsigned int lcsr = LCSR;
+	unsigned int lcsr = readl_relaxed(fbi->base + LCSR);
 
 	if (lcsr & LCSR_LDD) {
-		LCCR0 |= LCCR0_LDM;
+		u32 lccr0 = readl_relaxed(fbi->base + LCCR0) | LCCR0_LDM;
+		writel_relaxed(lccr0, fbi->base + LCCR0);
 		wake_up(&fbi->ctrlr_wait);
 	}
 
-	LCSR = lcsr;
+	writel_relaxed(lcsr, fbi->base + LCSR);
 	return IRQ_HANDLED;
 }
 
@@ -1268,7 +1040,7 @@
 	switch (val) {
 	case CPUFREQ_ADJUST:
 	case CPUFREQ_INCOMPATIBLE:
-		printk(KERN_DEBUG "min dma period: %d ps, "
+		dev_dbg(fbi->dev, "min dma period: %d ps, "
 			"new clock %d kHz\n", sa1100fb_min_dma_period(fbi),
 			policy->max);
 		/* todo: fill in min/max values */
@@ -1318,7 +1090,7 @@
  *      cache.  Once this area is remapped, all virtual memory
  *      access to the video memory should occur at the new region.
  */
-static int __init sa1100fb_map_video_memory(struct sa1100fb_info *fbi)
+static int __devinit sa1100fb_map_video_memory(struct sa1100fb_info *fbi)
 {
 	/*
 	 * We reserve one page for the palette, plus the size
@@ -1344,7 +1116,7 @@
 }
 
 /* Fake monspecs to fill in fbinfo structure */
-static struct fb_monspecs monspecs __initdata = {
+static struct fb_monspecs monspecs __devinitdata = {
 	.hfmin	= 30000,
 	.hfmax	= 70000,
 	.vfmin	= 50,
@@ -1352,10 +1124,11 @@
 };
 
 
-static struct sa1100fb_info * __init sa1100fb_init_fbinfo(struct device *dev)
+static struct sa1100fb_info * __devinit sa1100fb_init_fbinfo(struct device *dev)
 {
-	struct sa1100fb_mach_info *inf;
+	struct sa1100fb_mach_info *inf = dev->platform_data;
 	struct sa1100fb_info *fbi;
+	unsigned i;
 
 	fbi = kmalloc(sizeof(struct sa1100fb_info) + sizeof(u32) * 16,
 		      GFP_KERNEL);
@@ -1390,8 +1163,6 @@
 	fbi->rgb[RGB_8]		= &rgb_8;
 	fbi->rgb[RGB_16]	= &def_rgb_16;
 
-	inf = sa1100fb_get_machine_info(fbi);
-
 	/*
 	 * People just don't seem to get this.  We don't support
 	 * anything but correct entries now, so panic if someone
@@ -1402,13 +1173,10 @@
 		panic("sa1100fb error: invalid LCCR3 fields set or zero "
 			"pixclock.");
 
-	fbi->max_xres			= inf->xres;
 	fbi->fb.var.xres		= inf->xres;
 	fbi->fb.var.xres_virtual	= inf->xres;
-	fbi->max_yres			= inf->yres;
 	fbi->fb.var.yres		= inf->yres;
 	fbi->fb.var.yres_virtual	= inf->yres;
-	fbi->max_bpp			= inf->bpp;
 	fbi->fb.var.bits_per_pixel	= inf->bpp;
 	fbi->fb.var.pixclock		= inf->pixclock;
 	fbi->fb.var.hsync_len		= inf->hsync_len;
@@ -1419,14 +1187,16 @@
 	fbi->fb.var.lower_margin	= inf->lower_margin;
 	fbi->fb.var.sync		= inf->sync;
 	fbi->fb.var.grayscale		= inf->cmap_greyscale;
-	fbi->cmap_inverse		= inf->cmap_inverse;
-	fbi->cmap_static		= inf->cmap_static;
-	fbi->lccr0			= inf->lccr0;
-	fbi->lccr3			= inf->lccr3;
 	fbi->state			= C_STARTUP;
 	fbi->task_state			= (u_char)-1;
-	fbi->fb.fix.smem_len		= fbi->max_xres * fbi->max_yres *
-					  fbi->max_bpp / 8;
+	fbi->fb.fix.smem_len		= inf->xres * inf->yres *
+					  inf->bpp / 8;
+	fbi->inf			= inf;
+
+	/* Copy the RGB bitfield overrides */
+	for (i = 0; i < NR_RGB; i++)
+		if (inf->rgb[i])
+			fbi->rgb[i] = inf->rgb[i];
 
 	init_waitqueue_head(&fbi->ctrlr_wait);
 	INIT_WORK(&fbi->task, sa1100fb_task);
@@ -1438,13 +1208,20 @@
 static int __devinit sa1100fb_probe(struct platform_device *pdev)
 {
 	struct sa1100fb_info *fbi;
+	struct resource *res;
 	int ret, irq;
 
+	if (!pdev->dev.platform_data) {
+		dev_err(&pdev->dev, "no platform LCD data\n");
+		return -EINVAL;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	irq = platform_get_irq(pdev, 0);
-	if (irq < 0)
+	if (irq < 0 || !res)
 		return -EINVAL;
 
-	if (!request_mem_region(0xb0100000, 0x10000, "LCD"))
+	if (!request_mem_region(res->start, resource_size(res), "LCD"))
 		return -EBUSY;
 
 	fbi = sa1100fb_init_fbinfo(&pdev->dev);
@@ -1452,6 +1229,10 @@
 	if (!fbi)
 		goto failed;
 
+	fbi->base = ioremap(res->start, resource_size(res));
+	if (!fbi->base)
+		goto failed;
+
 	/* Initialize video memory */
 	ret = sa1100fb_map_video_memory(fbi);
 	if (ret)
@@ -1459,14 +1240,16 @@
 
 	ret = request_irq(irq, sa1100fb_handle_irq, 0, "LCD", fbi);
 	if (ret) {
-		printk(KERN_ERR "sa1100fb: request_irq failed: %d\n", ret);
+		dev_err(&pdev->dev, "request_irq failed: %d\n", ret);
 		goto failed;
 	}
 
-#ifdef ASSABET_PAL_VIDEO
-	if (machine_is_assabet())
-		ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
-#endif
+	if (machine_is_shannon()) {
+		ret = gpio_request_one(SHANNON_GPIO_DISP_EN,
+			GPIOF_OUT_INIT_LOW, "display enable");
+		if (ret)
+			goto err_free_irq;
+	}
 
 	/*
 	 * This makes sure that our colour bitfield
@@ -1478,7 +1261,7 @@
 
 	ret = register_framebuffer(&fbi->fb);
 	if (ret < 0)
-		goto err_free_irq;
+		goto err_reg_fb;
 
 #ifdef CONFIG_CPU_FREQ
 	fbi->freq_transition.notifier_call = sa1100fb_freq_transition;
@@ -1490,12 +1273,17 @@
 	/* This driver cannot be unloaded at the moment */
 	return 0;
 
+ err_reg_fb:
+	if (machine_is_shannon())
+		gpio_free(SHANNON_GPIO_DISP_EN);
  err_free_irq:
 	free_irq(irq, fbi);
  failed:
+	if (fbi)
+		iounmap(fbi->base);
 	platform_set_drvdata(pdev, NULL);
 	kfree(fbi);
-	release_mem_region(0xb0100000, 0x10000);
+	release_mem_region(res->start, resource_size(res));
 	return ret;
 }
 
@@ -1505,6 +1293,7 @@
 	.resume		= sa1100fb_resume,
 	.driver		= {
 		.name	= "sa11x0-fb",
+		.owner	= THIS_MODULE,
 	},
 };
 
diff --git a/drivers/video/sa1100fb.h b/drivers/video/sa1100fb.h
index 1c3b459..fc5d429 100644
--- a/drivers/video/sa1100fb.h
+++ b/drivers/video/sa1100fb.h
@@ -10,44 +10,15 @@
  * for more details.
  */
 
-/*
- * These are the bitfields for each
- * display depth that we support.
- */
-struct sa1100fb_rgb {
-	struct fb_bitfield	red;
-	struct fb_bitfield	green;
-	struct fb_bitfield	blue;
-	struct fb_bitfield	transp;
-};
-
-/*
- * This structure describes the machine which we are running on.
- */
-struct sa1100fb_mach_info {
-	u_long		pixclock;
-
-	u_short		xres;
-	u_short		yres;
-
-	u_char		bpp;
-	u_char		hsync_len;
-	u_char		left_margin;
-	u_char		right_margin;
-
-	u_char		vsync_len;
-	u_char		upper_margin;
-	u_char		lower_margin;
-	u_char		sync;
-
-	u_int		cmap_greyscale:1,
-			cmap_inverse:1,
-			cmap_static:1,
-			unused:29;
-
-	u_int		lccr0;
-	u_int		lccr3;
-};
+#define LCCR0           0x0000          /* LCD Control Reg. 0 */
+#define LCSR            0x0004          /* LCD Status Reg. */
+#define DBAR1           0x0010          /* LCD DMA Base Address Reg. channel 1 */
+#define DCAR1           0x0014          /* LCD DMA Current Address Reg. channel 1 */
+#define DBAR2           0x0018          /* LCD DMA Base Address Reg.  channel 2 */
+#define DCAR2           0x001C          /* LCD DMA Current Address Reg. channel 2 */
+#define LCCR1           0x0020          /* LCD Control Reg. 1 */
+#define LCCR2           0x0024          /* LCD Control Reg. 2 */
+#define LCCR3           0x0028          /* LCD Control Reg. 3 */
 
 /* Shadows for LCD controller registers */
 struct sa1100fb_lcd_reg {
@@ -57,19 +28,11 @@
 	unsigned long lccr3;
 };
 
-#define RGB_4	(0)
-#define RGB_8	(1)
-#define RGB_16	(2)
-#define NR_RGB	3
-
 struct sa1100fb_info {
 	struct fb_info		fb;
 	struct device		*dev;
-	struct sa1100fb_rgb	*rgb[NR_RGB];
-
-	u_int			max_bpp;
-	u_int			max_xres;
-	u_int			max_yres;
+	const struct sa1100fb_rgb *rgb[NR_RGB];
+	void __iomem		*base;
 
 	/*
 	 * These are the addresses we mapped
@@ -88,12 +51,6 @@
 	dma_addr_t		dbar1;
 	dma_addr_t		dbar2;
 
-	u_int			lccr0;
-	u_int			lccr3;
-	u_int			cmap_inverse:1,
-				cmap_static:1,
-				unused:30;
-
 	u_int			reg_lccr0;
 	u_int			reg_lccr1;
 	u_int			reg_lccr2;
@@ -109,6 +66,8 @@
 	struct notifier_block	freq_transition;
 	struct notifier_block	freq_policy;
 #endif
+
+	const struct sa1100fb_mach_info *inf;
 };
 
 #define TO_INF(ptr,member)	container_of(ptr,struct sa1100fb_info,member)
@@ -130,15 +89,6 @@
 #define SA1100_NAME	"SA1100"
 
 /*
- *  Debug macros 
- */
-#if DEBUG
-#  define DPRINTK(fmt, args...)	printk("%s: " fmt, __func__ , ## args)
-#else
-#  define DPRINTK(fmt, args...)
-#endif
-
-/*
  * Minimum X and Y resolutions
  */
 #define MIN_XRES	64
diff --git a/include/video/sa1100fb.h b/include/video/sa1100fb.h
new file mode 100644
index 0000000..4ab4096
--- /dev/null
+++ b/include/video/sa1100fb.h
@@ -0,0 +1,63 @@
+/*
+ * StrongARM 1100 LCD Controller Frame Buffer Device
+ *
+ * Copyright (C) 1999 Eric A. Thomas
+ *  Based on acornfb.c Copyright (C) Russell King.
+ *  
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive
+ * for more details.
+ */
+#ifndef _VIDEO_SA1100FB_H
+#define _VIDEO_SA1100FB_H
+
+#include <linux/fb.h>
+#include <linux/types.h>
+
+#define RGB_4	0
+#define RGB_8	1
+#define RGB_16	2
+#define NR_RGB	3
+
+/* These are the bitfields for each display depth that we support. */
+struct sa1100fb_rgb {
+	struct fb_bitfield	red;
+	struct fb_bitfield	green;
+	struct fb_bitfield	blue;
+	struct fb_bitfield	transp;
+};
+
+/* This structure describes the machine which we are running on. */
+struct sa1100fb_mach_info {
+	u_long		pixclock;
+
+	u_short		xres;
+	u_short		yres;
+
+	u_char		bpp;
+	u_char		hsync_len;
+	u_char		left_margin;
+	u_char		right_margin;
+
+	u_char		vsync_len;
+	u_char		upper_margin;
+	u_char		lower_margin;
+	u_char		sync;
+
+	u_int		cmap_greyscale:1,
+			cmap_inverse:1,
+			cmap_static:1,
+			unused:29;
+
+	u_int		lccr0;
+	u_int		lccr3;
+
+	/* Overrides for the default RGB maps */
+	const struct sa1100fb_rgb *rgb[NR_RGB];
+
+	void (*backlight_power)(int);
+	void (*lcd_power)(int);
+	void (*set_visual)(u32);
+};
+
+#endif