| /* |
| * arch/arm/mach-pxa/include/mach/viper.h |
| * |
| * Author: Ian Campbell |
| * Created: Feb 03, 2003 |
| * Copyright: Arcom Control Systems. |
| * |
| * Maintained by Marc Zyngier <maz@misterjones.org> |
| * <marc.zyngier@altran.com> |
| * |
| * Created based on lubbock.h: |
| * Author: Nicolas Pitre |
| * Created: Jun 15, 2001 |
| * Copyright: MontaVista Software Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #ifndef ARCH_VIPER_H |
| #define ARCH_VIPER_H |
| |
| #define VIPER_BOOT_PHYS PXA_CS0_PHYS |
| #define VIPER_FLASH_PHYS PXA_CS1_PHYS |
| #define VIPER_ETH_PHYS PXA_CS2_PHYS |
| #define VIPER_USB_PHYS PXA_CS3_PHYS |
| #define VIPER_ETH_DATA_PHYS PXA_CS4_PHYS |
| #define VIPER_CPLD_PHYS PXA_CS5_PHYS |
| |
| #define VIPER_CPLD_BASE (0xf0000000) |
| #define VIPER_PC104IO_BASE (0xf1000000) |
| #define VIPER_USB_BASE (0xf1800000) |
| |
| #define VIPER_ETH_GPIO (0) |
| #define VIPER_CPLD_GPIO (1) |
| #define VIPER_USB_GPIO (2) |
| #define VIPER_UARTA_GPIO (4) |
| #define VIPER_UARTB_GPIO (3) |
| #define VIPER_CF_CD_GPIO (32) |
| #define VIPER_CF_RDY_GPIO (8) |
| #define VIPER_BCKLIGHT_EN_GPIO (9) |
| #define VIPER_LCD_EN_GPIO (10) |
| #define VIPER_PSU_DATA_GPIO (6) |
| #define VIPER_PSU_CLK_GPIO (11) |
| #define VIPER_UART_SHDN_GPIO (12) |
| #define VIPER_BRIGHTNESS_GPIO (16) |
| #define VIPER_PSU_nCS_LD_GPIO (19) |
| #define VIPER_UPS_GPIO (20) |
| #define VIPER_CF_POWER_GPIO (82) |
| #define VIPER_TPM_I2C_SDA_GPIO (26) |
| #define VIPER_TPM_I2C_SCL_GPIO (27) |
| #define VIPER_RTC_I2C_SDA_GPIO (83) |
| #define VIPER_RTC_I2C_SCL_GPIO (84) |
| |
| #define VIPER_CPLD_P2V(x) ((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE) |
| #define VIPER_CPLD_V2P(x) ((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS) |
| |
| #ifndef __ASSEMBLY__ |
| # define __VIPER_CPLD_REG(x) (*((volatile u16 *)VIPER_CPLD_P2V(x))) |
| #endif |
| |
| /* board level registers in the CPLD: (offsets from CPLD_BASE) ... */ |
| |
| /* ... Physical addresses */ |
| #define _VIPER_LO_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100000) |
| #define _VIPER_ICR_PHYS (VIPER_CPLD_PHYS + 0x100002) |
| #define _VIPER_HI_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100004) |
| #define _VIPER_VERSION_PHYS (VIPER_CPLD_PHYS + 0x100006) |
| #define VIPER_UARTA_PHYS (VIPER_CPLD_PHYS + 0x300010) |
| #define VIPER_UARTB_PHYS (VIPER_CPLD_PHYS + 0x300000) |
| #define _VIPER_SRAM_BASE (VIPER_CPLD_PHYS + 0x800000) |
| |
| /* ... Virtual addresses */ |
| #define VIPER_LO_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS) |
| #define VIPER_HI_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS) |
| #define VIPER_VERSION __VIPER_CPLD_REG(_VIPER_VERSION_PHYS) |
| #define VIPER_ICR __VIPER_CPLD_REG(_VIPER_ICR_PHYS) |
| |
| /* Decode VIPER_VERSION register */ |
| #define VIPER_CPLD_REVISION(x) (((x) >> 5) & 0x7) |
| #define VIPER_BOARD_VERSION(x) (((x) >> 3) & 0x3) |
| #define VIPER_BOARD_ISSUE(x) (((x) >> 0) & 0x7) |
| |
| /* Interrupt and Configuration Register (VIPER_ICR) */ |
| /* This is a write only register. Only CF_RST is used under Linux */ |
| |
| #define VIPER_ICR_RETRIG (1 << 0) |
| #define VIPER_ICR_AUTO_CLR (1 << 1) |
| #define VIPER_ICR_R_DIS (1 << 2) |
| #define VIPER_ICR_CF_RST (1 << 3) |
| |
| #endif |
| |
