diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
new file mode 100644
index 0000000..56edb552
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -0,0 +1,28 @@
+* ST Microelectronics STMPE Multi-Functional Device
+
+STMPE is an MFD device which may expose the following inbuilt devices: gpio,
+keypad, touchscreen, adc, pwm, rotator.
+
+Required properties:
+ - compatible                   : "st,stmpe[610|801|811|1601|2401|2403]"
+ - reg                          : I2C/SPI address of the device
+
+Optional properties:
+ - interrupts                   : The interrupt outputs from the controller
+ - interrupt-controller         : Marks the device node as an interrupt controller
+ - interrupt-parent             : Specifies which IRQ controller we're connected to
+ - wakeup-source                : Marks the input device as wakable
+ - st,autosleep-timeout         : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
+
+Example:
+
+	stmpe1601: stmpe1601@40 {
+		compatible = "st,stmpe1601";
+		reg = <0x40>;
+		interrupts = <26 0x4>;
+		interrupt-parent = <&gpio6>;
+		interrupt-controller;
+
+		wakeup-source;
+		st,autosleep-timeout = <1024>;
+	};
diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt
index d316fb8..4f05d20 100644
--- a/Documentation/devicetree/bindings/regulator/tps65217.txt
+++ b/Documentation/devicetree/bindings/regulator/tps65217.txt
@@ -11,6 +11,9 @@
   using the standard binding for regulators found at
   Documentation/devicetree/bindings/regulator/regulator.txt.
 
+Optional properties:
+- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle.
+
   The valid names for regulators are:
   tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4
 
@@ -20,6 +23,7 @@
 
 	tps: tps@24 {
 		compatible = "ti,tps65217";
+		ti,pmic-shutdown-controller;
 
 		regulators {
 			dcdc1_reg: dcdc1 {
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index bf892bd..8ae1f5b 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -683,4 +683,17 @@
 	  Enable support for GPIO on intel MSIC controllers found in
 	  intel MID devices
 
+comment "USB GPIO expanders:"
+
+config GPIO_VIPERBOARD
+	tristate "Viperboard GPIO a & b support"
+	depends on MFD_VIPERBOARD && USB
+	help
+	  Say yes here to access the GPIO signals of Nano River
+	  Technologies Viperboard. There are two GPIO chips on the
+	  board: gpioa and gpiob.
+          See viperboard API specification and Nano
+          River Tech's viperboard.h for detailed meaning
+          of the module parameters.
+
 endif
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 76b3446..c5aebd0 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -76,6 +76,7 @@
 obj-$(CONFIG_GPIO_TWL4030)	+= gpio-twl4030.o
 obj-$(CONFIG_GPIO_TWL6040)	+= gpio-twl6040.o
 obj-$(CONFIG_GPIO_UCB1400)	+= gpio-ucb1400.o
+obj-$(CONFIG_GPIO_VIPERBOARD)	+= gpio-viperboard.o
 obj-$(CONFIG_GPIO_VR41XX)	+= gpio-vr41xx.o
 obj-$(CONFIG_GPIO_VT8500)	+= gpio-vt8500.o
 obj-$(CONFIG_GPIO_VX855)	+= gpio-vx855.o
diff --git a/drivers/gpio/gpio-da9052.c b/drivers/gpio/gpio-da9052.c
index a05aacd..29b11e9 100644
--- a/drivers/gpio/gpio-da9052.c
+++ b/drivers/gpio/gpio-da9052.c
@@ -185,7 +185,11 @@
 	struct da9052_gpio *gpio = to_da9052_gpio(gc);
 	struct da9052 *da9052 = gpio->da9052;
 
-	return da9052->irq_base + DA9052_IRQ_GPI0 + offset;
+	int irq;
+
+	irq = regmap_irq_get_virq(da9052->irq_data, DA9052_IRQ_GPI0 + offset);
+
+	return irq;
 }
 
 static struct gpio_chip reference_gp = {
diff --git a/drivers/gpio/gpio-tps6586x.c b/drivers/gpio/gpio-tps6586x.c
index c1b82da..29e8e75 100644
--- a/drivers/gpio/gpio-tps6586x.c
+++ b/drivers/gpio/gpio-tps6586x.c
@@ -80,6 +80,14 @@
 				val, mask);
 }
 
+static int tps6586x_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
+{
+	struct tps6586x_gpio *tps6586x_gpio = to_tps6586x_gpio(gc);
+
+	return tps6586x_irq_get_virq(tps6586x_gpio->parent,
+				TPS6586X_INT_PLDO_0 + offset);
+}
+
 static int tps6586x_gpio_probe(struct platform_device *pdev)
 {
 	struct tps6586x_platform_data *pdata;
@@ -106,6 +114,7 @@
 	tps6586x_gpio->gpio_chip.direction_output = tps6586x_gpio_output;
 	tps6586x_gpio->gpio_chip.set	= tps6586x_gpio_set;
 	tps6586x_gpio->gpio_chip.get	= tps6586x_gpio_get;
+	tps6586x_gpio->gpio_chip.to_irq	= tps6586x_gpio_to_irq;
 
 #ifdef CONFIG_OF_GPIO
 	tps6586x_gpio->gpio_chip.of_node = pdev->dev.parent->of_node;
diff --git a/drivers/gpio/gpio-twl4030.c b/drivers/gpio/gpio-twl4030.c
index 00329f2..9572aa1 100644
--- a/drivers/gpio/gpio-twl4030.c
+++ b/drivers/gpio/gpio-twl4030.c
@@ -355,13 +355,13 @@
 
 static int gpio_twl4030_pulls(u32 ups, u32 downs)
 {
-	u8		message[6];
+	u8		message[5];
 	unsigned	i, gpio_bit;
 
 	/* For most pins, a pulldown was enabled by default.
 	 * We should have data that's specific to this board.
 	 */
-	for (gpio_bit = 1, i = 1; i < 6; i++) {
+	for (gpio_bit = 1, i = 0; i < 5; i++) {
 		u8		bit_mask;
 		unsigned	j;
 
@@ -380,16 +380,16 @@
 
 static int gpio_twl4030_debounce(u32 debounce, u8 mmc_cd)
 {
-	u8		message[4];
+	u8		message[3];
 
 	/* 30 msec of debouncing is always used for MMC card detect,
 	 * and is optional for everything else.
 	 */
-	message[1] = (debounce & 0xff) | (mmc_cd & 0x03);
+	message[0] = (debounce & 0xff) | (mmc_cd & 0x03);
 	debounce >>= 8;
-	message[2] = (debounce & 0xff);
+	message[1] = (debounce & 0xff);
 	debounce >>= 8;
-	message[3] = (debounce & 0x03);
+	message[2] = (debounce & 0x03);
 
 	return twl_i2c_write(TWL4030_MODULE_GPIO, message,
 				REG_GPIO_DEBEN1, 3);
diff --git a/drivers/gpio/gpio-viperboard.c b/drivers/gpio/gpio-viperboard.c
new file mode 100644
index 0000000..1377299
--- /dev/null
+++ b/drivers/gpio/gpio-viperboard.c
@@ -0,0 +1,517 @@
+/*
+ *  Nano River Technologies viperboard GPIO lib driver
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#include <linux/usb.h>
+#include <linux/gpio.h>
+
+#include <linux/mfd/viperboard.h>
+
+#define VPRBRD_GPIOA_CLK_1MHZ		0
+#define VPRBRD_GPIOA_CLK_100KHZ		1
+#define VPRBRD_GPIOA_CLK_10KHZ		2
+#define VPRBRD_GPIOA_CLK_1KHZ		3
+#define VPRBRD_GPIOA_CLK_100HZ		4
+#define VPRBRD_GPIOA_CLK_10HZ		5
+
+#define VPRBRD_GPIOA_FREQ_DEFAULT	1000
+
+#define VPRBRD_GPIOA_CMD_CONT		0x00
+#define VPRBRD_GPIOA_CMD_PULSE		0x01
+#define VPRBRD_GPIOA_CMD_PWM		0x02
+#define VPRBRD_GPIOA_CMD_SETOUT		0x03
+#define VPRBRD_GPIOA_CMD_SETIN		0x04
+#define VPRBRD_GPIOA_CMD_SETINT		0x05
+#define VPRBRD_GPIOA_CMD_GETIN		0x06
+
+#define VPRBRD_GPIOB_CMD_SETDIR		0x00
+#define VPRBRD_GPIOB_CMD_SETVAL		0x01
+
+struct vprbrd_gpioa_msg {
+	u8 cmd;
+	u8 clk;
+	u8 offset;
+	u8 t1;
+	u8 t2;
+	u8 invert;
+	u8 pwmlevel;
+	u8 outval;
+	u8 risefall;
+	u8 answer;
+	u8 __fill;
+} __packed;
+
+struct vprbrd_gpiob_msg {
+	u8 cmd;
+	u16 val;
+	u16 mask;
+} __packed;
+
+struct vprbrd_gpio {
+	struct gpio_chip gpioa; /* gpio a related things */
+	u32 gpioa_out;
+	u32 gpioa_val;
+	struct gpio_chip gpiob; /* gpio b related things */
+	u32 gpiob_out;
+	u32 gpiob_val;
+	struct vprbrd *vb;
+};
+
+/* gpioa sampling clock module parameter */
+static unsigned char gpioa_clk;
+static unsigned int gpioa_freq = VPRBRD_GPIOA_FREQ_DEFAULT;
+module_param(gpioa_freq, uint, 0);
+MODULE_PARM_DESC(gpioa_freq,
+	"gpio-a sampling freq in Hz (default is 1000Hz) valid values: 10, 100, 1000, 10000, 100000, 1000000");
+
+/* ----- begin of gipo a chip -------------------------------------------- */
+
+static int vprbrd_gpioa_get(struct gpio_chip *chip,
+		unsigned offset)
+{
+	int ret, answer, error = 0;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpioa);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpioa_msg *gamsg = (struct vprbrd_gpioa_msg *)vb->buf;
+
+	/* if io is set to output, just return the saved value */
+	if (gpio->gpioa_out & (1 << offset))
+		return gpio->gpioa_val & (1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	gamsg->cmd = VPRBRD_GPIOA_CMD_GETIN;
+	gamsg->clk = 0x00;
+	gamsg->offset = offset;
+	gamsg->t1 = 0x00;
+	gamsg->t2 = 0x00;
+	gamsg->invert = 0x00;
+	gamsg->pwmlevel = 0x00;
+	gamsg->outval = 0x00;
+	gamsg->risefall = 0x00;
+	gamsg->answer = 0x00;
+	gamsg->__fill = 0x00;
+
+	ret = usb_control_msg(vb->usb_dev, usb_sndctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOA, VPRBRD_USB_TYPE_OUT, 0x0000,
+		0x0000, gamsg, sizeof(struct vprbrd_gpioa_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+	if (ret != sizeof(struct vprbrd_gpioa_msg))
+		error = -EREMOTEIO;
+
+	ret = usb_control_msg(vb->usb_dev, usb_rcvctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOA, VPRBRD_USB_TYPE_IN, 0x0000,
+		0x0000, gamsg, sizeof(struct vprbrd_gpioa_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+	answer = gamsg->answer & 0x01;
+
+	mutex_unlock(&vb->lock);
+
+	if (ret != sizeof(struct vprbrd_gpioa_msg))
+		error = -EREMOTEIO;
+
+	if (error)
+		return error;
+
+	return answer;
+}
+
+static void vprbrd_gpioa_set(struct gpio_chip *chip,
+		unsigned offset, int value)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpioa);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpioa_msg *gamsg = (struct vprbrd_gpioa_msg *)vb->buf;
+
+	if (gpio->gpioa_out & (1 << offset)) {
+		if (value)
+			gpio->gpioa_val |= (1 << offset);
+		else
+			gpio->gpioa_val &= ~(1 << offset);
+
+		mutex_lock(&vb->lock);
+
+		gamsg->cmd = VPRBRD_GPIOA_CMD_SETOUT;
+		gamsg->clk = 0x00;
+		gamsg->offset = offset;
+		gamsg->t1 = 0x00;
+		gamsg->t2 = 0x00;
+		gamsg->invert = 0x00;
+		gamsg->pwmlevel = 0x00;
+		gamsg->outval = value;
+		gamsg->risefall = 0x00;
+		gamsg->answer = 0x00;
+		gamsg->__fill = 0x00;
+
+		ret = usb_control_msg(vb->usb_dev,
+			usb_sndctrlpipe(vb->usb_dev, 0),
+			VPRBRD_USB_REQUEST_GPIOA, VPRBRD_USB_TYPE_OUT,
+			0x0000,	0x0000, gamsg,
+			sizeof(struct vprbrd_gpioa_msg), VPRBRD_USB_TIMEOUT_MS);
+
+		mutex_unlock(&vb->lock);
+
+		if (ret != sizeof(struct vprbrd_gpioa_msg))
+			dev_err(chip->dev, "usb error setting pin value\n");
+	}
+}
+
+static int vprbrd_gpioa_direction_input(struct gpio_chip *chip,
+			unsigned offset)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpioa);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpioa_msg *gamsg = (struct vprbrd_gpioa_msg *)vb->buf;
+
+	gpio->gpioa_out &= ~(1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	gamsg->cmd = VPRBRD_GPIOA_CMD_SETIN;
+	gamsg->clk = gpioa_clk;
+	gamsg->offset = offset;
+	gamsg->t1 = 0x00;
+	gamsg->t2 = 0x00;
+	gamsg->invert = 0x00;
+	gamsg->pwmlevel = 0x00;
+	gamsg->outval = 0x00;
+	gamsg->risefall = 0x00;
+	gamsg->answer = 0x00;
+	gamsg->__fill = 0x00;
+
+	ret = usb_control_msg(vb->usb_dev, usb_sndctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOA, VPRBRD_USB_TYPE_OUT, 0x0000,
+		0x0000, gamsg, sizeof(struct vprbrd_gpioa_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+
+	mutex_unlock(&vb->lock);
+
+	if (ret != sizeof(struct vprbrd_gpioa_msg))
+		return -EREMOTEIO;
+
+	return 0;
+}
+
+static int vprbrd_gpioa_direction_output(struct gpio_chip *chip,
+			unsigned offset, int value)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpioa);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpioa_msg *gamsg = (struct vprbrd_gpioa_msg *)vb->buf;
+
+	gpio->gpioa_out |= (1 << offset);
+	if (value)
+		gpio->gpioa_val |= (1 << offset);
+	else
+		gpio->gpioa_val &= ~(1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	gamsg->cmd = VPRBRD_GPIOA_CMD_SETOUT;
+	gamsg->clk = 0x00;
+	gamsg->offset = offset;
+	gamsg->t1 = 0x00;
+	gamsg->t2 = 0x00;
+	gamsg->invert = 0x00;
+	gamsg->pwmlevel = 0x00;
+	gamsg->outval = value;
+	gamsg->risefall = 0x00;
+	gamsg->answer = 0x00;
+	gamsg->__fill = 0x00;
+
+	ret = usb_control_msg(vb->usb_dev, usb_sndctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOA, VPRBRD_USB_TYPE_OUT, 0x0000,
+		0x0000, gamsg, sizeof(struct vprbrd_gpioa_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+
+	mutex_unlock(&vb->lock);
+
+	if (ret != sizeof(struct vprbrd_gpioa_msg))
+		return -EREMOTEIO;
+
+	return 0;
+}
+
+/* ----- end of gpio a chip ---------------------------------------------- */
+
+/* ----- begin of gipo b chip -------------------------------------------- */
+
+static int vprbrd_gpiob_setdir(struct vprbrd *vb, unsigned offset,
+	unsigned dir)
+{
+	struct vprbrd_gpiob_msg *gbmsg = (struct vprbrd_gpiob_msg *)vb->buf;
+	int ret;
+
+	gbmsg->cmd = VPRBRD_GPIOB_CMD_SETDIR;
+	gbmsg->val = cpu_to_be16(dir << offset);
+	gbmsg->mask = cpu_to_be16(0x0001 << offset);
+
+	ret = usb_control_msg(vb->usb_dev, usb_sndctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOB, VPRBRD_USB_TYPE_OUT, 0x0000,
+		0x0000, gbmsg, sizeof(struct vprbrd_gpiob_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+
+	if (ret != sizeof(struct vprbrd_gpiob_msg))
+		return -EREMOTEIO;
+
+	return 0;
+}
+
+static int vprbrd_gpiob_get(struct gpio_chip *chip,
+		unsigned offset)
+{
+	int ret;
+	u16 val;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpiob);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpiob_msg *gbmsg = (struct vprbrd_gpiob_msg *)vb->buf;
+
+	/* if io is set to output, just return the saved value */
+	if (gpio->gpiob_out & (1 << offset))
+		return gpio->gpiob_val & (1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	ret = usb_control_msg(vb->usb_dev, usb_rcvctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_GPIOB, VPRBRD_USB_TYPE_IN, 0x0000,
+		0x0000, gbmsg,	sizeof(struct vprbrd_gpiob_msg),
+		VPRBRD_USB_TIMEOUT_MS);
+	val = gbmsg->val;
+
+	mutex_unlock(&vb->lock);
+
+	if (ret != sizeof(struct vprbrd_gpiob_msg))
+		return ret;
+
+	/* cache the read values */
+	gpio->gpiob_val = be16_to_cpu(val);
+
+	return (gpio->gpiob_val >> offset) & 0x1;
+}
+
+static void vprbrd_gpiob_set(struct gpio_chip *chip,
+		unsigned offset, int value)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpiob);
+	struct vprbrd *vb = gpio->vb;
+	struct vprbrd_gpiob_msg *gbmsg = (struct vprbrd_gpiob_msg *)vb->buf;
+
+	if (gpio->gpiob_out & (1 << offset)) {
+		if (value)
+			gpio->gpiob_val |= (1 << offset);
+		else
+			gpio->gpiob_val &= ~(1 << offset);
+
+		mutex_lock(&vb->lock);
+
+		gbmsg->cmd = VPRBRD_GPIOB_CMD_SETVAL;
+		gbmsg->val = cpu_to_be16(value << offset);
+		gbmsg->mask = cpu_to_be16(0x0001 << offset);
+
+		ret = usb_control_msg(vb->usb_dev,
+			usb_sndctrlpipe(vb->usb_dev, 0),
+			VPRBRD_USB_REQUEST_GPIOB, VPRBRD_USB_TYPE_OUT,
+			0x0000,	0x0000, gbmsg,
+			sizeof(struct vprbrd_gpiob_msg), VPRBRD_USB_TIMEOUT_MS);
+
+		mutex_unlock(&vb->lock);
+
+		if (ret != sizeof(struct vprbrd_gpiob_msg))
+			dev_err(chip->dev, "usb error setting pin value\n");
+	}
+}
+
+static int vprbrd_gpiob_direction_input(struct gpio_chip *chip,
+			unsigned offset)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpiob);
+	struct vprbrd *vb = gpio->vb;
+
+	gpio->gpiob_out &= ~(1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	ret = vprbrd_gpiob_setdir(vb, offset, 0);
+
+	mutex_unlock(&vb->lock);
+
+	if (ret)
+		dev_err(chip->dev, "usb error setting pin to input\n");
+
+	return ret;
+}
+
+static int vprbrd_gpiob_direction_output(struct gpio_chip *chip,
+			unsigned offset, int value)
+{
+	int ret;
+	struct vprbrd_gpio *gpio =
+			container_of(chip, struct vprbrd_gpio, gpiob);
+	struct vprbrd *vb = gpio->vb;
+
+	gpio->gpiob_out |= (1 << offset);
+	if (value)
+		gpio->gpiob_val |= (1 << offset);
+	else
+		gpio->gpiob_val &= ~(1 << offset);
+
+	mutex_lock(&vb->lock);
+
+	ret = vprbrd_gpiob_setdir(vb, offset, 1);
+	if (ret)
+		dev_err(chip->dev, "usb error setting pin to output\n");
+
+	mutex_unlock(&vb->lock);
+
+	vprbrd_gpiob_set(chip, offset, value);
+
+	return ret;
+}
+
+/* ----- end of gpio b chip ---------------------------------------------- */
+
+static int __devinit vprbrd_gpio_probe(struct platform_device *pdev)
+{
+	struct vprbrd *vb = dev_get_drvdata(pdev->dev.parent);
+	struct vprbrd_gpio *vb_gpio;
+	int ret;
+
+	vb_gpio = devm_kzalloc(&pdev->dev, sizeof(*vb_gpio), GFP_KERNEL);
+	if (vb_gpio == NULL)
+		return -ENOMEM;
+
+	vb_gpio->vb = vb;
+	/* registering gpio a */
+	vb_gpio->gpioa.label = "viperboard gpio a";
+	vb_gpio->gpioa.dev = &pdev->dev;
+	vb_gpio->gpioa.owner = THIS_MODULE;
+	vb_gpio->gpioa.base = -1;
+	vb_gpio->gpioa.ngpio = 16;
+	vb_gpio->gpioa.can_sleep = 1;
+	vb_gpio->gpioa.set = vprbrd_gpioa_set;
+	vb_gpio->gpioa.get = vprbrd_gpioa_get;
+	vb_gpio->gpioa.direction_input = vprbrd_gpioa_direction_input;
+	vb_gpio->gpioa.direction_output = vprbrd_gpioa_direction_output;
+	ret = gpiochip_add(&vb_gpio->gpioa);
+	if (ret < 0) {
+		dev_err(vb_gpio->gpioa.dev, "could not add gpio a");
+		goto err_gpioa;
+	}
+
+	/* registering gpio b */
+	vb_gpio->gpiob.label = "viperboard gpio b";
+	vb_gpio->gpiob.dev = &pdev->dev;
+	vb_gpio->gpiob.owner = THIS_MODULE;
+	vb_gpio->gpiob.base = -1;
+	vb_gpio->gpiob.ngpio = 16;
+	vb_gpio->gpiob.can_sleep = 1;
+	vb_gpio->gpiob.set = vprbrd_gpiob_set;
+	vb_gpio->gpiob.get = vprbrd_gpiob_get;
+	vb_gpio->gpiob.direction_input = vprbrd_gpiob_direction_input;
+	vb_gpio->gpiob.direction_output = vprbrd_gpiob_direction_output;
+	ret = gpiochip_add(&vb_gpio->gpiob);
+	if (ret < 0) {
+		dev_err(vb_gpio->gpiob.dev, "could not add gpio b");
+		goto err_gpiob;
+	}
+
+	platform_set_drvdata(pdev, vb_gpio);
+
+	return ret;
+
+err_gpiob:
+	ret = gpiochip_remove(&vb_gpio->gpioa);
+
+err_gpioa:
+	return ret;
+}
+
+static int __devexit vprbrd_gpio_remove(struct platform_device *pdev)
+{
+	struct vprbrd_gpio *vb_gpio = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = gpiochip_remove(&vb_gpio->gpiob);
+	if (ret == 0)
+		ret = gpiochip_remove(&vb_gpio->gpioa);
+
+	return ret;
+}
+
+static struct platform_driver vprbrd_gpio_driver = {
+	.driver.name	= "viperboard-gpio",
+	.driver.owner	= THIS_MODULE,
+	.probe		= vprbrd_gpio_probe,
+	.remove		= __devexit_p(vprbrd_gpio_remove),
+};
+
+static int __init vprbrd_gpio_init(void)
+{
+	switch (gpioa_freq) {
+	case 1000000:
+		gpioa_clk = VPRBRD_GPIOA_CLK_1MHZ;
+		break;
+	case 100000:
+		gpioa_clk = VPRBRD_GPIOA_CLK_100KHZ;
+		break;
+	case 10000:
+		gpioa_clk = VPRBRD_GPIOA_CLK_10KHZ;
+		break;
+	case 1000:
+		gpioa_clk = VPRBRD_GPIOA_CLK_1KHZ;
+		break;
+	case 100:
+		gpioa_clk = VPRBRD_GPIOA_CLK_100HZ;
+		break;
+	case 10:
+		gpioa_clk = VPRBRD_GPIOA_CLK_10HZ;
+		break;
+	default:
+		pr_warn("invalid gpioa_freq (%d)\n", gpioa_freq);
+		gpioa_clk = VPRBRD_GPIOA_CLK_1KHZ;
+	}
+
+	return platform_driver_register(&vprbrd_gpio_driver);
+}
+subsys_initcall(vprbrd_gpio_init);
+
+static void __exit vprbrd_gpio_exit(void)
+{
+	platform_driver_unregister(&vprbrd_gpio_driver);
+}
+module_exit(vprbrd_gpio_exit);
+
+MODULE_AUTHOR("Lars Poeschel <poeschel@lemonage.de>");
+MODULE_DESCRIPTION("GPIO driver for Nano River Techs Viperboard");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:viperboard-gpio");
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index e9df461..c7bff51 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -818,6 +818,16 @@
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-tiny-usb.
 
+config I2C_VIPERBOARD
+	tristate "Viperboard I2C master support"
+	depends on MFD_VIPERBOARD && USB
+	help
+	  Say yes here to access the I2C part of the Nano River
+	  Technologies Viperboard as I2C master.
+          See viperboard API specification and Nano
+          River Tech's viperboard.h for detailed meaning
+          of the module parameters.
+
 comment "Other I2C/SMBus bus drivers"
 
 config I2C_ACORN
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 395b516..e5cb209 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -79,6 +79,7 @@
 obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_TAOS_EVM)	+= i2c-taos-evm.o
 obj-$(CONFIG_I2C_TINY_USB)	+= i2c-tiny-usb.o
+obj-$(CONFIG_I2C_VIPERBOARD)	+= i2c-viperboard.o
 
 # Other I2C/SMBus bus drivers
 obj-$(CONFIG_I2C_ACORN)		+= i2c-acorn.o
diff --git a/drivers/i2c/busses/i2c-viperboard.c b/drivers/i2c/busses/i2c-viperboard.c
new file mode 100644
index 0000000..f5fa20d
--- /dev/null
+++ b/drivers/i2c/busses/i2c-viperboard.c
@@ -0,0 +1,480 @@
+/*
+ *  Nano River Technologies viperboard i2c master driver
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#include <linux/usb.h>
+#include <linux/i2c.h>
+
+#include <linux/mfd/viperboard.h>
+
+struct vprbrd_i2c {
+	struct i2c_adapter i2c;
+	u8 bus_freq_param;
+};
+
+/* i2c bus frequency module parameter */
+static u8 i2c_bus_param;
+static unsigned int i2c_bus_freq = 100;
+module_param(i2c_bus_freq, int, 0);
+MODULE_PARM_DESC(i2c_bus_freq,
+	"i2c bus frequency in khz (default is 100) valid values: 10, 100, 200, 400, 1000, 3000, 6000");
+
+static int vprbrd_i2c_status(struct i2c_adapter *i2c,
+	struct vprbrd_i2c_status *status, bool prev_error)
+{
+	u16 bytes_xfer;
+	int ret;
+	struct vprbrd *vb = (struct vprbrd *)i2c->algo_data;
+
+	/* check for protocol error */
+	bytes_xfer = sizeof(struct vprbrd_i2c_status);
+
+	ret = usb_control_msg(vb->usb_dev, usb_rcvctrlpipe(vb->usb_dev, 0),
+		VPRBRD_USB_REQUEST_I2C, VPRBRD_USB_TYPE_IN, 0x0000, 0x0000,
+		status, bytes_xfer, VPRBRD_USB_TIMEOUT_MS);
+
+	if (ret != bytes_xfer)
+		prev_error = true;
+
+	if (prev_error) {
+		dev_err(&i2c->dev, "failure in usb communication\n");
+		return -EREMOTEIO;
+	}
+
+	dev_dbg(&i2c->dev, "  status = %d\n", status->status);
+	if (status->status != 0x00) {
+		dev_err(&i2c->dev, "failure: i2c protocol error\n");
+		return -EPROTO;
+	}
+	return 0;
+}
+
+static int vprbrd_i2c_receive(struct usb_device *usb_dev,
+	struct vprbrd_i2c_read_msg *rmsg, int bytes_xfer)
+{
+	int ret, bytes_actual;
+	int error = 0;
+
+	/* send the read request */
+	ret = usb_bulk_msg(usb_dev,
+		usb_sndbulkpipe(usb_dev, VPRBRD_EP_OUT), rmsg,
+		sizeof(struct vprbrd_i2c_read_hdr), &bytes_actual,
+		VPRBRD_USB_TIMEOUT_MS);
+
+	if ((ret < 0)
+		|| (bytes_actual != sizeof(struct vprbrd_i2c_read_hdr))) {
+		dev_err(&usb_dev->dev, "failure transmitting usb\n");
+		error = -EREMOTEIO;
+	}
+
+	/* read the actual data */
+	ret = usb_bulk_msg(usb_dev,
+		usb_rcvbulkpipe(usb_dev, VPRBRD_EP_IN), rmsg,
+		bytes_xfer, &bytes_actual, VPRBRD_USB_TIMEOUT_MS);
+
+	if ((ret < 0) || (bytes_xfer != bytes_actual)) {
+		dev_err(&usb_dev->dev, "failure receiving usb\n");
+		error = -EREMOTEIO;
+	}
+	return error;
+}
+
+static int vprbrd_i2c_addr(struct usb_device *usb_dev,
+	struct vprbrd_i2c_addr_msg *amsg)
+{
+	int ret, bytes_actual;
+
+	ret = usb_bulk_msg(usb_dev,
+		usb_sndbulkpipe(usb_dev, VPRBRD_EP_OUT), amsg,
+		sizeof(struct vprbrd_i2c_addr_msg), &bytes_actual,
+		VPRBRD_USB_TIMEOUT_MS);
+
+	if ((ret < 0) ||
+			(sizeof(struct vprbrd_i2c_addr_msg) != bytes_actual)) {
+		dev_err(&usb_dev->dev, "failure transmitting usb\n");
+		return -EREMOTEIO;
+	}
+	return 0;
+}
+
+static int vprbrd_i2c_read(struct vprbrd *vb, struct i2c_msg *msg)
+{
+	int ret;
+	u16 remain_len, bytes_xfer, len1, len2,
+		start = 0x0000;
+	struct vprbrd_i2c_read_msg *rmsg =
+		(struct vprbrd_i2c_read_msg *)vb->buf;
+
+	remain_len = msg->len;
+	rmsg->header.cmd = VPRBRD_I2C_CMD_READ;
+	while (remain_len > 0) {
+		rmsg->header.addr = cpu_to_le16(start + 0x4000);
+		if (remain_len <= 255) {
+			len1 = remain_len;
+			len2 = 0x00;
+			rmsg->header.len0 = remain_len;
+			rmsg->header.len1 = 0x00;
+			rmsg->header.len2 = 0x00;
+			rmsg->header.len3 = 0x00;
+			rmsg->header.len4 = 0x00;
+			rmsg->header.len5 = 0x00;
+			remain_len = 0;
+		} else if (remain_len <= 510) {
+			len1 = remain_len;
+			len2 = 0x00;
+			rmsg->header.len0 = remain_len - 255;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0x00;
+			rmsg->header.len3 = 0x00;
+			rmsg->header.len4 = 0x00;
+			rmsg->header.len5 = 0x00;
+			remain_len = 0;
+		} else if (remain_len <= 512) {
+			len1 = remain_len;
+			len2 = 0x00;
+			rmsg->header.len0 = remain_len - 510;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0xff;
+			rmsg->header.len3 = 0x00;
+			rmsg->header.len4 = 0x00;
+			rmsg->header.len5 = 0x00;
+			remain_len = 0;
+		} else if (remain_len <= 767) {
+			len1 = 512;
+			len2 = remain_len - 512;
+			rmsg->header.len0 = 0x02;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0xff;
+			rmsg->header.len3 = remain_len - 512;
+			rmsg->header.len4 = 0x00;
+			rmsg->header.len5 = 0x00;
+			bytes_xfer = remain_len;
+			remain_len = 0;
+		} else if (remain_len <= 1022) {
+			len1 = 512;
+			len2 = remain_len - 512;
+			rmsg->header.len0 = 0x02;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0xff;
+			rmsg->header.len3 = remain_len - 767;
+			rmsg->header.len4 = 0xff;
+			rmsg->header.len5 = 0x00;
+			remain_len = 0;
+		} else if (remain_len <= 1024) {
+			len1 = 512;
+			len2 = remain_len - 512;
+			rmsg->header.len0 = 0x02;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0xff;
+			rmsg->header.len3 = remain_len - 1022;
+			rmsg->header.len4 = 0xff;
+			rmsg->header.len5 = 0xff;
+			remain_len = 0;
+		} else {
+			len1 = 512;
+			len2 = 512;
+			rmsg->header.len0 = 0x02;
+			rmsg->header.len1 = 0xff;
+			rmsg->header.len2 = 0xff;
+			rmsg->header.len3 = 0x02;
+			rmsg->header.len4 = 0xff;
+			rmsg->header.len5 = 0xff;
+			remain_len -= 1024;
+			start += 1024;
+		}
+		rmsg->header.tf1 = cpu_to_le16(len1);
+		rmsg->header.tf2 = cpu_to_le16(len2);
+
+		/* first read transfer */
+		ret = vprbrd_i2c_receive(vb->usb_dev, rmsg, len1);
+		if (ret < 0)
+			return ret;
+		/* copy the received data */
+		memcpy(msg->buf + start, rmsg, len1);
+
+		/* second read transfer if neccessary */
+		if (len2 > 0) {
+			ret = vprbrd_i2c_receive(vb->usb_dev, rmsg, len2);
+			if (ret < 0)
+				return ret;
+			/* copy the received data */
+			memcpy(msg->buf + start + 512, rmsg, len2);
+		}
+	}
+	return 0;
+}
+
+static int vprbrd_i2c_write(struct vprbrd *vb, struct i2c_msg *msg)
+{
+	int ret, bytes_actual;
+	u16 remain_len, bytes_xfer,
+		start = 0x0000;
+	struct vprbrd_i2c_write_msg *wmsg =
+		(struct vprbrd_i2c_write_msg *)vb->buf;
+
+	remain_len = msg->len;
+	wmsg->header.cmd = VPRBRD_I2C_CMD_WRITE;
+	wmsg->header.last = 0x00;
+	wmsg->header.chan = 0x00;
+	wmsg->header.spi = 0x0000;
+	while (remain_len > 0) {
+		wmsg->header.addr = cpu_to_le16(start + 0x4000);
+		if (remain_len > 503) {
+			wmsg->header.len1 = 0xff;
+			wmsg->header.len2 = 0xf8;
+			remain_len -= 503;
+			bytes_xfer = 503 + sizeof(struct vprbrd_i2c_write_hdr);
+			start += 503;
+		} else if (remain_len > 255) {
+			wmsg->header.len1 = 0xff;
+			wmsg->header.len2 = (remain_len - 255);
+			bytes_xfer = remain_len +
+				sizeof(struct vprbrd_i2c_write_hdr);
+			remain_len = 0;
+		} else {
+			wmsg->header.len1 = remain_len;
+			wmsg->header.len2 = 0x00;
+			bytes_xfer = remain_len +
+				sizeof(struct vprbrd_i2c_write_hdr);
+			remain_len = 0;
+		}
+		memcpy(wmsg->data, msg->buf + start,
+			bytes_xfer - sizeof(struct vprbrd_i2c_write_hdr));
+
+		ret = usb_bulk_msg(vb->usb_dev,
+			usb_sndbulkpipe(vb->usb_dev,
+			VPRBRD_EP_OUT), wmsg,
+			bytes_xfer, &bytes_actual, VPRBRD_USB_TIMEOUT_MS);
+		if ((ret < 0) || (bytes_xfer != bytes_actual))
+			return -EREMOTEIO;
+	}
+	return 0;
+}
+
+static int vprbrd_i2c_xfer(struct i2c_adapter *i2c, struct i2c_msg *msgs,
+		int num)
+{
+	struct i2c_msg *pmsg;
+	int i, ret,
+		error = 0;
+	struct vprbrd *vb = (struct vprbrd *)i2c->algo_data;
+	struct vprbrd_i2c_addr_msg *amsg =
+		(struct vprbrd_i2c_addr_msg *)vb->buf;
+	struct vprbrd_i2c_status *smsg = (struct vprbrd_i2c_status *)vb->buf;
+
+	dev_dbg(&i2c->dev, "master xfer %d messages:\n", num);
+
+	for (i = 0 ; i < num ; i++) {
+		pmsg = &msgs[i];
+
+		dev_dbg(&i2c->dev,
+			"  %d: %s (flags %d) %d bytes to 0x%02x\n",
+			i, pmsg->flags & I2C_M_RD ? "read" : "write",
+			pmsg->flags, pmsg->len, pmsg->addr);
+
+		/* msgs longer than 2048 bytes are not supported by adapter */
+		if (pmsg->len > 2048)
+			return -EINVAL;
+
+		mutex_lock(&vb->lock);
+		/* directly send the message */
+		if (pmsg->flags & I2C_M_RD) {
+			/* read data */
+			amsg->cmd = VPRBRD_I2C_CMD_ADDR;
+			amsg->unknown2 = 0x00;
+			amsg->unknown3 = 0x00;
+			amsg->addr = pmsg->addr;
+			amsg->unknown1 = 0x01;
+			amsg->len = cpu_to_le16(pmsg->len);
+			/* send the addr and len, we're interested to board */
+			ret = vprbrd_i2c_addr(vb->usb_dev, amsg);
+			if (ret < 0)
+				error = ret;
+
+			ret = vprbrd_i2c_read(vb, pmsg);
+			if (ret < 0)
+				error = ret;
+
+			ret = vprbrd_i2c_status(i2c, smsg, error);
+			if (ret < 0)
+				error = ret;
+			/* in case of protocol error, return the error */
+			if (error < 0)
+				goto error;
+		} else {
+			/* write data */
+			ret = vprbrd_i2c_write(vb, pmsg);
+
+			amsg->cmd = VPRBRD_I2C_CMD_ADDR;
+			amsg->unknown2 = 0x00;
+			amsg->unknown3 = 0x00;
+			amsg->addr = pmsg->addr;
+			amsg->unknown1 = 0x00;
+			amsg->len = cpu_to_le16(pmsg->len);
+			/* send the addr, the data goes to to board */
+			ret = vprbrd_i2c_addr(vb->usb_dev, amsg);
+			if (ret < 0)
+				error = ret;
+
+			ret = vprbrd_i2c_status(i2c, smsg, error);
+			if (ret < 0)
+				error = ret;
+
+			if (error < 0)
+				goto error;
+		}
+		mutex_unlock(&vb->lock);
+	}
+	return 0;
+error:
+	mutex_unlock(&vb->lock);
+	return error;
+}
+
+static u32 vprbrd_i2c_func(struct i2c_adapter *i2c)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+/* This is the actual algorithm we define */
+static const struct i2c_algorithm vprbrd_algorithm = {
+	.master_xfer	= vprbrd_i2c_xfer,
+	.functionality	= vprbrd_i2c_func,
+};
+
+static int __devinit vprbrd_i2c_probe(struct platform_device *pdev)
+{
+	struct vprbrd *vb = dev_get_drvdata(pdev->dev.parent);
+	struct vprbrd_i2c *vb_i2c;
+	int ret;
+	int pipe;
+
+	vb_i2c = kzalloc(sizeof(*vb_i2c), GFP_KERNEL);
+	if (vb_i2c == NULL)
+		return -ENOMEM;
+
+	/* setup i2c adapter description */
+	vb_i2c->i2c.owner = THIS_MODULE;
+	vb_i2c->i2c.class = I2C_CLASS_HWMON;
+	vb_i2c->i2c.algo = &vprbrd_algorithm;
+	vb_i2c->i2c.algo_data = vb;
+	/* save the param in usb capabable memory */
+	vb_i2c->bus_freq_param = i2c_bus_param;
+
+	snprintf(vb_i2c->i2c.name, sizeof(vb_i2c->i2c.name),
+		 "viperboard at bus %03d device %03d",
+		 vb->usb_dev->bus->busnum, vb->usb_dev->devnum);
+
+	/* setting the bus frequency */
+	if ((i2c_bus_param <= VPRBRD_I2C_FREQ_10KHZ)
+		&& (i2c_bus_param >= VPRBRD_I2C_FREQ_6MHZ)) {
+		pipe = usb_sndctrlpipe(vb->usb_dev, 0);
+		ret = usb_control_msg(vb->usb_dev, pipe,
+			VPRBRD_USB_REQUEST_I2C_FREQ, VPRBRD_USB_TYPE_OUT,
+			0x0000, 0x0000, &vb_i2c->bus_freq_param, 1,
+			VPRBRD_USB_TIMEOUT_MS);
+	    if (ret != 1) {
+		dev_err(&pdev->dev,
+			"failure setting i2c_bus_freq to %d\n", i2c_bus_freq);
+		ret = -EIO;
+		goto error;
+	    }
+	} else {
+		dev_err(&pdev->dev,
+			"invalid i2c_bus_freq setting:%d\n", i2c_bus_freq);
+		ret = -EIO;
+		goto error;
+	}
+
+	vb_i2c->i2c.dev.parent = &pdev->dev;
+
+	/* attach to i2c layer */
+	i2c_add_adapter(&vb_i2c->i2c);
+
+	platform_set_drvdata(pdev, vb_i2c);
+
+	return 0;
+
+error:
+	kfree(vb_i2c);
+	return ret;
+}
+
+static int __devexit vprbrd_i2c_remove(struct platform_device *pdev)
+{
+	struct vprbrd_i2c *vb_i2c = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = i2c_del_adapter(&vb_i2c->i2c);
+
+	return ret;
+}
+
+static struct platform_driver vprbrd_i2c_driver = {
+	.driver.name	= "viperboard-i2c",
+	.driver.owner	= THIS_MODULE,
+	.probe		= vprbrd_i2c_probe,
+	.remove		= __devexit_p(vprbrd_i2c_remove),
+};
+
+static int __init vprbrd_i2c_init(void)
+{
+	switch (i2c_bus_freq) {
+	case 6000:
+		i2c_bus_param = VPRBRD_I2C_FREQ_6MHZ;
+		break;
+	case 3000:
+		i2c_bus_param = VPRBRD_I2C_FREQ_3MHZ;
+		break;
+	case 1000:
+		i2c_bus_param = VPRBRD_I2C_FREQ_1MHZ;
+		break;
+	case 400:
+		i2c_bus_param = VPRBRD_I2C_FREQ_400KHZ;
+		break;
+	case 200:
+		i2c_bus_param = VPRBRD_I2C_FREQ_200KHZ;
+		break;
+	case 100:
+		i2c_bus_param = VPRBRD_I2C_FREQ_100KHZ;
+		break;
+	case 10:
+		i2c_bus_param = VPRBRD_I2C_FREQ_10KHZ;
+		break;
+	default:
+		pr_warn("invalid i2c_bus_freq (%d)\n", i2c_bus_freq);
+		i2c_bus_param = VPRBRD_I2C_FREQ_100KHZ;
+	}
+
+	return platform_driver_register(&vprbrd_i2c_driver);
+}
+subsys_initcall(vprbrd_i2c_init);
+
+static void __exit vprbrd_i2c_exit(void)
+{
+	platform_driver_unregister(&vprbrd_i2c_driver);
+}
+module_exit(vprbrd_i2c_exit);
+
+MODULE_AUTHOR("Lars Poeschel <poeschel@lemonage.de>");
+MODULE_DESCRIPTION("I2C master driver for Nano River Techs Viperboard");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:viperboard-i2c");
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 961b8d0..fe822a1 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -125,4 +125,18 @@
 	  This driver can also be built as a module. If so, the module will be
 	  called ti-adc081c.
 
+config TI_AM335X_ADC
+	tristate "TI's ADC driver"
+	depends on MFD_TI_AM335X_TSCADC
+	help
+	  Say yes here to build support for Texas Instruments ADC
+	  driver which is also a MFD client.
+
+config VIPERBOARD_ADC
+	tristate "Viperboard ADC support"
+	depends on MFD_VIPERBOARD && USB
+	help
+	  Say yes here to access the ADC part of the Nano River
+	  Technologies Viperboard.
+
 endmenu
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 472fd7c..2d5f100 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -13,4 +13,5 @@
 obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
 obj-$(CONFIG_MAX1363) += max1363.o
 obj-$(CONFIG_TI_ADC081C) += ti-adc081c.o
-
+obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
+obj-$(CONFIG_VIPERBOARD_ADC) += viperboard_adc.o
diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
new file mode 100644
index 0000000..02a43c8
--- /dev/null
+++ b/drivers/iio/adc/ti_am335x_adc.c
@@ -0,0 +1,260 @@
+/*
+ * TI ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/iio/iio.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
+
+struct tiadc_device {
+	struct ti_tscadc_dev *mfd_tscadc;
+	int channels;
+};
+
+static unsigned int tiadc_readl(struct tiadc_device *adc, unsigned int reg)
+{
+	return readl(adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_writel(struct tiadc_device *adc, unsigned int reg,
+					unsigned int val)
+{
+	writel(val, adc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void tiadc_step_config(struct tiadc_device *adc_dev)
+{
+	unsigned int stepconfig;
+	int i, channels = 0, steps;
+
+	/*
+	 * There are 16 configurable steps and 8 analog input
+	 * lines available which are shared between Touchscreen and ADC.
+	 *
+	 * Steps backwards i.e. from 16 towards 0 are used by ADC
+	 * depending on number of input lines needed.
+	 * Channel would represent which analog input
+	 * needs to be given to ADC to digitalize data.
+	 */
+
+	steps = TOTAL_STEPS - adc_dev->channels;
+	channels = TOTAL_CHANNELS - adc_dev->channels;
+
+	stepconfig = STEPCONFIG_AVG_16 | STEPCONFIG_FIFO1;
+
+	for (i = (steps + 1); i <= TOTAL_STEPS; i++) {
+		tiadc_writel(adc_dev, REG_STEPCONFIG(i),
+				stepconfig | STEPCONFIG_INP(channels));
+		tiadc_writel(adc_dev, REG_STEPDELAY(i),
+				STEPCONFIG_OPENDLY);
+		channels++;
+	}
+	tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+}
+
+static int tiadc_channel_init(struct iio_dev *indio_dev, int channels)
+{
+	struct iio_chan_spec *chan_array;
+	int i;
+
+	indio_dev->num_channels = channels;
+	chan_array = kcalloc(indio_dev->num_channels,
+			sizeof(struct iio_chan_spec), GFP_KERNEL);
+
+	if (chan_array == NULL)
+		return -ENOMEM;
+
+	for (i = 0; i < (indio_dev->num_channels); i++) {
+		struct iio_chan_spec *chan = chan_array + i;
+		chan->type = IIO_VOLTAGE;
+		chan->indexed = 1;
+		chan->channel = i;
+		chan->info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT;
+	}
+
+	indio_dev->channels = chan_array;
+
+	return indio_dev->num_channels;
+}
+
+static void tiadc_channels_remove(struct iio_dev *indio_dev)
+{
+	kfree(indio_dev->channels);
+}
+
+static int tiadc_read_raw(struct iio_dev *indio_dev,
+		struct iio_chan_spec const *chan,
+		int *val, int *val2, long mask)
+{
+	struct tiadc_device *adc_dev = iio_priv(indio_dev);
+	int i;
+	unsigned int fifo1count, readx1;
+
+	/*
+	 * When the sub-system is first enabled,
+	 * the sequencer will always start with the
+	 * lowest step (1) and continue until step (16).
+	 * For ex: If we have enabled 4 ADC channels and
+	 * currently use only 1 out of them, the
+	 * sequencer still configures all the 4 steps,
+	 * leading to 3 unwanted data.
+	 * Hence we need to flush out this data.
+	 */
+
+	fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
+	for (i = 0; i < fifo1count; i++) {
+		readx1 = tiadc_readl(adc_dev, REG_FIFO1);
+		if (i == chan->channel)
+			*val = readx1 & 0xfff;
+	}
+	tiadc_writel(adc_dev, REG_SE, STPENB_STEPENB);
+
+	return IIO_VAL_INT;
+}
+
+static const struct iio_info tiadc_info = {
+	.read_raw = &tiadc_read_raw,
+};
+
+static int __devinit tiadc_probe(struct platform_device *pdev)
+{
+	struct iio_dev		*indio_dev;
+	struct tiadc_device	*adc_dev;
+	struct ti_tscadc_dev	*tscadc_dev = pdev->dev.platform_data;
+	struct mfd_tscadc_board	*pdata;
+	int			err;
+
+	pdata = tscadc_dev->dev->platform_data;
+	if (!pdata || !pdata->adc_init) {
+		dev_err(&pdev->dev, "Could not find platform data\n");
+		return -EINVAL;
+	}
+
+	indio_dev = iio_device_alloc(sizeof(struct tiadc_device));
+	if (indio_dev == NULL) {
+		dev_err(&pdev->dev, "failed to allocate iio device\n");
+		err = -ENOMEM;
+		goto err_ret;
+	}
+	adc_dev = iio_priv(indio_dev);
+
+	adc_dev->mfd_tscadc = tscadc_dev;
+	adc_dev->channels = pdata->adc_init->adc_channels;
+
+	indio_dev->dev.parent = &pdev->dev;
+	indio_dev->name = dev_name(&pdev->dev);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &tiadc_info;
+
+	tiadc_step_config(adc_dev);
+
+	err = tiadc_channel_init(indio_dev, adc_dev->channels);
+	if (err < 0)
+		goto err_free_device;
+
+	err = iio_device_register(indio_dev);
+	if (err)
+		goto err_free_channels;
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	return 0;
+
+err_free_channels:
+	tiadc_channels_remove(indio_dev);
+err_free_device:
+	iio_device_free(indio_dev);
+err_ret:
+	return err;
+}
+
+static int __devexit tiadc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+	iio_device_unregister(indio_dev);
+	tiadc_channels_remove(indio_dev);
+
+	iio_device_free(indio_dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int tiadc_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct tiadc_device *adc_dev = iio_priv(indio_dev);
+	struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+	unsigned int idle;
+
+	if (!device_may_wakeup(tscadc_dev->dev)) {
+		idle = tiadc_readl(adc_dev, REG_CTRL);
+		idle &= ~(CNTRLREG_TSCSSENB);
+		tiadc_writel(adc_dev, REG_CTRL, (idle |
+				CNTRLREG_POWERDOWN));
+	}
+
+	return 0;
+}
+
+static int tiadc_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct tiadc_device *adc_dev = iio_priv(indio_dev);
+	unsigned int restore;
+
+	/* Make sure ADC is powered up */
+	restore = tiadc_readl(adc_dev, REG_CTRL);
+	restore &= ~(CNTRLREG_POWERDOWN);
+	tiadc_writel(adc_dev, REG_CTRL, restore);
+
+	tiadc_step_config(adc_dev);
+
+	return 0;
+}
+
+static const struct dev_pm_ops tiadc_pm_ops = {
+	.suspend = tiadc_suspend,
+	.resume = tiadc_resume,
+};
+#define TIADC_PM_OPS (&tiadc_pm_ops)
+#else
+#define TIADC_PM_OPS NULL
+#endif
+
+static struct platform_driver tiadc_driver = {
+	.driver = {
+		.name   = "tiadc",
+		.owner	= THIS_MODULE,
+		.pm	= TIADC_PM_OPS,
+	},
+	.probe	= tiadc_probe,
+	.remove	= __devexit_p(tiadc_remove),
+};
+
+module_platform_driver(tiadc_driver);
+
+MODULE_DESCRIPTION("TI ADC controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/iio/adc/viperboard_adc.c b/drivers/iio/adc/viperboard_adc.c
new file mode 100644
index 0000000..10136a8
--- /dev/null
+++ b/drivers/iio/adc/viperboard_adc.c
@@ -0,0 +1,181 @@
+/*
+ *  Nano River Technologies viperboard IIO ADC driver
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#include <linux/usb.h>
+#include <linux/iio/iio.h>
+
+#include <linux/mfd/viperboard.h>
+
+#define VPRBRD_ADC_CMD_GET		0x00
+
+struct vprbrd_adc_msg {
+	u8 cmd;
+	u8 chan;
+	u8 val;
+} __packed;
+
+struct vprbrd_adc {
+	struct vprbrd *vb;
+};
+
+#define VPRBRD_ADC_CHANNEL(_index) {			\
+	.type = IIO_VOLTAGE,				\
+	.indexed = 1,					\
+	.channel = _index,				\
+	.info_mask = IIO_CHAN_INFO_RAW_SEPARATE_BIT,	\
+	.scan_index = _index,				\
+	.scan_type = {					\
+		.sign = 'u',				\
+		.realbits = 8,				\
+		.storagebits = 8,			\
+	},						\
+}
+
+static struct iio_chan_spec const vprbrd_adc_iio_channels[] = {
+	VPRBRD_ADC_CHANNEL(0),
+	VPRBRD_ADC_CHANNEL(1),
+	VPRBRD_ADC_CHANNEL(2),
+	VPRBRD_ADC_CHANNEL(3),
+};
+
+static int vprbrd_iio_read_raw(struct iio_dev *iio_dev,
+				struct iio_chan_spec const *chan,
+				int *val,
+				int *val2,
+				long info)
+{
+	int ret, error = 0;
+	struct vprbrd_adc *adc = iio_priv(iio_dev);
+	struct vprbrd *vb = adc->vb;
+	struct vprbrd_adc_msg *admsg = (struct vprbrd_adc_msg *)vb->buf;
+
+	switch (info) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&vb->lock);
+
+		admsg->cmd = VPRBRD_ADC_CMD_GET;
+		admsg->chan = chan->scan_index;
+		admsg->val = 0x00;
+
+		ret = usb_control_msg(vb->usb_dev,
+			usb_sndctrlpipe(vb->usb_dev, 0), VPRBRD_USB_REQUEST_ADC,
+			VPRBRD_USB_TYPE_OUT, 0x0000, 0x0000, admsg,
+			sizeof(struct vprbrd_adc_msg), VPRBRD_USB_TIMEOUT_MS);
+		if (ret != sizeof(struct vprbrd_adc_msg)) {
+			dev_err(&iio_dev->dev, "usb send error on adc read\n");
+			error = -EREMOTEIO;
+		}
+
+		ret = usb_control_msg(vb->usb_dev,
+			usb_rcvctrlpipe(vb->usb_dev, 0), VPRBRD_USB_REQUEST_ADC,
+			VPRBRD_USB_TYPE_IN, 0x0000, 0x0000, admsg,
+			sizeof(struct vprbrd_adc_msg), VPRBRD_USB_TIMEOUT_MS);
+
+		*val = admsg->val;
+
+		mutex_unlock(&vb->lock);
+
+		if (ret != sizeof(struct vprbrd_adc_msg)) {
+			dev_err(&iio_dev->dev, "usb recv error on adc read\n");
+			error = -EREMOTEIO;
+		}
+
+		if (error)
+			goto error;
+
+		return IIO_VAL_INT;
+	default:
+		error = -EINVAL;
+		break;
+	}
+error:
+	return error;
+}
+
+static const struct iio_info vprbrd_adc_iio_info = {
+	.read_raw = &vprbrd_iio_read_raw,
+	.driver_module = THIS_MODULE,
+};
+
+static int __devinit vprbrd_adc_probe(struct platform_device *pdev)
+{
+	struct vprbrd *vb = dev_get_drvdata(pdev->dev.parent);
+	struct vprbrd_adc *adc;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	/* registering iio */
+	indio_dev = iio_device_alloc(sizeof(*adc));
+	if (!indio_dev) {
+		dev_err(&pdev->dev, "failed allocating iio device\n");
+		return -ENOMEM;
+	}
+
+	adc = iio_priv(indio_dev);
+	adc->vb = vb;
+	indio_dev->name = "viperboard adc";
+	indio_dev->dev.parent = &pdev->dev;
+	indio_dev->info = &vprbrd_adc_iio_info;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->channels = vprbrd_adc_iio_channels;
+	indio_dev->num_channels = ARRAY_SIZE(vprbrd_adc_iio_channels);
+
+	ret = iio_device_register(indio_dev);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register iio (adc)");
+		goto error;
+	}
+
+	platform_set_drvdata(pdev, indio_dev);
+
+	return 0;
+
+error:
+	iio_device_free(indio_dev);
+	return ret;
+}
+
+static int __devexit vprbrd_adc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+	iio_device_unregister(indio_dev);
+	iio_device_free(indio_dev);
+
+	return 0;
+}
+
+static struct platform_driver vprbrd_adc_driver = {
+	.driver = {
+		.name	= "viperboard-adc",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= vprbrd_adc_probe,
+	.remove		= __devexit_p(vprbrd_adc_remove),
+};
+
+module_platform_driver(vprbrd_adc_driver);
+
+MODULE_AUTHOR("Lars Poeschel <poeschel@lemonage.de>");
+MODULE_DESCRIPTION("IIO ADC driver for Nano River Techs Viperboard");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:viperboard-adc");
diff --git a/drivers/input/misc/da9052_onkey.c b/drivers/input/misc/da9052_onkey.c
index 3c843cd..3be3acc 100644
--- a/drivers/input/misc/da9052_onkey.c
+++ b/drivers/input/misc/da9052_onkey.c
@@ -24,7 +24,6 @@
 	struct da9052 *da9052;
 	struct input_dev *input;
 	struct delayed_work work;
-	unsigned int irq;
 };
 
 static void da9052_onkey_query(struct da9052_onkey *onkey)
@@ -76,7 +75,6 @@
 	struct da9052 *da9052 = dev_get_drvdata(pdev->dev.parent);
 	struct da9052_onkey *onkey;
 	struct input_dev *input_dev;
-	int irq;
 	int error;
 
 	if (!da9052) {
@@ -84,13 +82,6 @@
 		return -EINVAL;
 	}
 
-	irq = platform_get_irq_byname(pdev, "ONKEY");
-	if (irq < 0) {
-		dev_err(&pdev->dev,
-			"Failed to get an IRQ for input device, %d\n", irq);
-		return -EINVAL;
-	}
-
 	onkey = kzalloc(sizeof(*onkey), GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!onkey || !input_dev) {
@@ -101,7 +92,6 @@
 
 	onkey->input = input_dev;
 	onkey->da9052 = da9052;
-	onkey->irq = irq;
 	INIT_DELAYED_WORK(&onkey->work, da9052_onkey_work);
 
 	input_dev->name = "da9052-onkey";
@@ -111,13 +101,11 @@
 	input_dev->evbit[0] = BIT_MASK(EV_KEY);
 	__set_bit(KEY_POWER, input_dev->keybit);
 
-	error = request_threaded_irq(onkey->irq, NULL, da9052_onkey_irq,
-				     IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				     "ONKEY", onkey);
+	error = da9052_request_irq(onkey->da9052, DA9052_IRQ_NONKEY, "ONKEY",
+			    da9052_onkey_irq, onkey);
 	if (error < 0) {
 		dev_err(onkey->da9052->dev,
-			"Failed to register ONKEY IRQ %d, error = %d\n",
-			onkey->irq, error);
+			"Failed to register ONKEY IRQ: %d\n", error);
 		goto err_free_mem;
 	}
 
@@ -132,7 +120,7 @@
 	return 0;
 
 err_free_irq:
-	free_irq(onkey->irq, onkey);
+	da9052_free_irq(onkey->da9052, DA9052_IRQ_NONKEY, onkey);
 	cancel_delayed_work_sync(&onkey->work);
 err_free_mem:
 	input_free_device(input_dev);
@@ -145,7 +133,7 @@
 {
 	struct da9052_onkey *onkey = platform_get_drvdata(pdev);
 
-	free_irq(onkey->irq, onkey);
+	da9052_free_irq(onkey->da9052, DA9052_IRQ_NONKEY, onkey);
 	cancel_delayed_work_sync(&onkey->work);
 
 	input_unregister_device(onkey->input);
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index f7668b2..0c45cad 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -529,9 +529,9 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called touchwin.
 
-config TOUCHSCREEN_TI_TSCADC
+config TOUCHSCREEN_TI_AM335X_TSC
 	tristate "TI Touchscreen Interface"
-	depends on ARCH_OMAP2PLUS
+	depends on MFD_TI_AM335X_TSCADC
 	help
 	  Say Y here if you have 4/5/8 wire touchscreen controller
 	  to be connected to the ADC controller on your TI AM335x SoC.
@@ -539,7 +539,7 @@
 	  If unsure, say N.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called ti_tscadc.
+	  module will be called ti_am335x_tsc.
 
 config TOUCHSCREEN_ATMEL_TSADCC
 	tristate "Atmel Touchscreen Interface"
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 178eb12..7c4c78e 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -52,7 +52,7 @@
 obj-$(CONFIG_TOUCHSCREEN_S3C2410)	+= s3c2410_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ST1232)	+= st1232.o
 obj-$(CONFIG_TOUCHSCREEN_STMPE)		+= stmpe-ts.o
-obj-$(CONFIG_TOUCHSCREEN_TI_TSCADC)	+= ti_tscadc.o
+obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TNETV107X)	+= tnetv107x-ts.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
diff --git a/drivers/input/touchscreen/da9052_tsi.c b/drivers/input/touchscreen/da9052_tsi.c
index e8df341..53133ef 100644
--- a/drivers/input/touchscreen/da9052_tsi.c
+++ b/drivers/input/touchscreen/da9052_tsi.c
@@ -27,8 +27,6 @@
 	struct input_dev *dev;
 	struct delayed_work ts_pen_work;
 	struct mutex mutex;
-	unsigned int irq_pendwn;
-	unsigned int irq_datardy;
 	bool stopped;
 	bool adc_on;
 };
@@ -45,8 +43,8 @@
 
 	if (!tsi->stopped) {
 		/* Mask PEN_DOWN event and unmask TSI_READY event */
-		disable_irq_nosync(tsi->irq_pendwn);
-		enable_irq(tsi->irq_datardy);
+		da9052_disable_irq_nosync(tsi->da9052, DA9052_IRQ_PENDOWN);
+		da9052_enable_irq(tsi->da9052, DA9052_IRQ_TSIREADY);
 
 		da9052_ts_adc_toggle(tsi, true);
 
@@ -137,8 +135,8 @@
 				return;
 
 			/* Mask TSI_READY event and unmask PEN_DOWN event */
-			disable_irq(tsi->irq_datardy);
-			enable_irq(tsi->irq_pendwn);
+			da9052_disable_irq(tsi->da9052, DA9052_IRQ_TSIREADY);
+			da9052_enable_irq(tsi->da9052, DA9052_IRQ_PENDOWN);
 		}
 	}
 }
@@ -197,7 +195,7 @@
 	mb();
 
 	/* Unmask PEN_DOWN event */
-	enable_irq(tsi->irq_pendwn);
+	da9052_enable_irq(tsi->da9052, DA9052_IRQ_PENDOWN);
 
 	/* Enable Pen Detect Circuit */
 	return da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG,
@@ -210,11 +208,11 @@
 
 	tsi->stopped = true;
 	mb();
-	disable_irq(tsi->irq_pendwn);
+	da9052_disable_irq(tsi->da9052, DA9052_IRQ_PENDOWN);
 	cancel_delayed_work_sync(&tsi->ts_pen_work);
 
 	if (tsi->adc_on) {
-		disable_irq(tsi->irq_datardy);
+		da9052_disable_irq(tsi->da9052, DA9052_IRQ_TSIREADY);
 		da9052_ts_adc_toggle(tsi, false);
 
 		/*
@@ -222,7 +220,7 @@
 		 * twice and we need to enable it to keep enable/disable
 		 * counter balanced. IRQ is still off though.
 		 */
-		enable_irq(tsi->irq_pendwn);
+		da9052_enable_irq(tsi->da9052, DA9052_IRQ_PENDOWN);
 	}
 
 	/* Disable Pen Detect Circuit */
@@ -234,21 +232,12 @@
 	struct da9052 *da9052;
 	struct da9052_tsi *tsi;
 	struct input_dev *input_dev;
-	int irq_pendwn;
-	int irq_datardy;
 	int error;
 
 	da9052 = dev_get_drvdata(pdev->dev.parent);
 	if (!da9052)
 		return -EINVAL;
 
-	irq_pendwn = platform_get_irq_byname(pdev, "PENDWN");
-	irq_datardy = platform_get_irq_byname(pdev, "TSIRDY");
-	if (irq_pendwn < 0 || irq_datardy < 0) {
-		dev_err(da9052->dev, "Unable to determine device interrupts\n");
-		return -ENXIO;
-	}
-
 	tsi = kzalloc(sizeof(struct da9052_tsi), GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!tsi || !input_dev) {
@@ -258,8 +247,6 @@
 
 	tsi->da9052 = da9052;
 	tsi->dev = input_dev;
-	tsi->irq_pendwn = da9052->irq_base + irq_pendwn;
-	tsi->irq_datardy = da9052->irq_base + irq_datardy;
 	tsi->stopped = true;
 	INIT_DELAYED_WORK(&tsi->ts_pen_work, da9052_ts_pen_work);
 
@@ -287,31 +274,25 @@
 	/* Disable ADC */
 	da9052_ts_adc_toggle(tsi, false);
 
-	error = request_threaded_irq(tsi->irq_pendwn,
-				     NULL, da9052_ts_pendwn_irq,
-				     IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				     "PENDWN", tsi);
+	error = da9052_request_irq(tsi->da9052, DA9052_IRQ_PENDOWN,
+				"pendown-irq", da9052_ts_pendwn_irq, tsi);
 	if (error) {
 		dev_err(tsi->da9052->dev,
-			"Failed to register PENDWN IRQ %d, error = %d\n",
-			tsi->irq_pendwn, error);
+			"Failed to register PENDWN IRQ: %d\n", error);
 		goto err_free_mem;
 	}
 
-	error = request_threaded_irq(tsi->irq_datardy,
-				     NULL, da9052_ts_datardy_irq,
-				     IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				     "TSIRDY", tsi);
+	error = da9052_request_irq(tsi->da9052, DA9052_IRQ_TSIREADY,
+				"tsiready-irq", da9052_ts_datardy_irq, tsi);
 	if (error) {
 		dev_err(tsi->da9052->dev,
-			"Failed to register TSIRDY IRQ %d, error = %d\n",
-			tsi->irq_datardy, error);
+			"Failed to register TSIRDY IRQ :%d\n", error);
 		goto err_free_pendwn_irq;
 	}
 
 	/* Mask PEN_DOWN and TSI_READY events */
-	disable_irq(tsi->irq_pendwn);
-	disable_irq(tsi->irq_datardy);
+	da9052_disable_irq(tsi->da9052, DA9052_IRQ_PENDOWN);
+	da9052_disable_irq(tsi->da9052, DA9052_IRQ_TSIREADY);
 
 	error = da9052_configure_tsi(tsi);
 	if (error)
@@ -326,9 +307,9 @@
 	return 0;
 
 err_free_datardy_irq:
-	free_irq(tsi->irq_datardy, tsi);
+	da9052_free_irq(tsi->da9052, DA9052_IRQ_TSIREADY, tsi);
 err_free_pendwn_irq:
-	free_irq(tsi->irq_pendwn, tsi);
+	da9052_free_irq(tsi->da9052, DA9052_IRQ_PENDOWN, tsi);
 err_free_mem:
 	kfree(tsi);
 	input_free_device(input_dev);
@@ -342,8 +323,8 @@
 
 	da9052_reg_write(tsi->da9052, DA9052_LDO9_REG, 0x19);
 
-	free_irq(tsi->irq_pendwn, tsi);
-	free_irq(tsi->irq_datardy, tsi);
+	da9052_free_irq(tsi->da9052, DA9052_IRQ_TSIREADY, tsi);
+	da9052_free_irq(tsi->da9052, DA9052_IRQ_PENDOWN, tsi);
 
 	input_unregister_device(tsi->dev);
 	kfree(tsi);
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
new file mode 100644
index 0000000..7a18a8a
--- /dev/null
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -0,0 +1,398 @@
+/*
+ * TI Touch Screen driver
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/input/ti_am335x_tsc.h>
+#include <linux/delay.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+
+#define ADCFSM_STEPID		0x10
+#define SEQ_SETTLE		275
+#define MAX_12BIT		((1 << 12) - 1)
+
+struct titsc {
+	struct input_dev	*input;
+	struct ti_tscadc_dev	*mfd_tscadc;
+	unsigned int		irq;
+	unsigned int		wires;
+	unsigned int		x_plate_resistance;
+	bool			pen_down;
+	int			steps_to_configure;
+};
+
+static unsigned int titsc_readl(struct titsc *ts, unsigned int reg)
+{
+	return readl(ts->mfd_tscadc->tscadc_base + reg);
+}
+
+static void titsc_writel(struct titsc *tsc, unsigned int reg,
+					unsigned int val)
+{
+	writel(val, tsc->mfd_tscadc->tscadc_base + reg);
+}
+
+static void titsc_step_config(struct titsc *ts_dev)
+{
+	unsigned int	config;
+	int i, total_steps;
+
+	/* Configure the Step registers */
+	total_steps = 2 * ts_dev->steps_to_configure;
+
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_AVG_16 | STEPCONFIG_XPP;
+	switch (ts_dev->wires) {
+	case 4:
+		config |= STEPCONFIG_INP_AN2 | STEPCONFIG_XNN;
+		break;
+	case 5:
+		config |= STEPCONFIG_YNN |
+				STEPCONFIG_INP_AN4 | STEPCONFIG_XNN |
+				STEPCONFIG_YPP;
+		break;
+	case 8:
+		config |= STEPCONFIG_INP_AN2 | STEPCONFIG_XNN;
+		break;
+	}
+
+	for (i = 1; i <= ts_dev->steps_to_configure; i++) {
+		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+	}
+
+	config = 0;
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_AVG_16 | STEPCONFIG_YNN |
+			STEPCONFIG_INM_ADCREFM | STEPCONFIG_FIFO1;
+	switch (ts_dev->wires) {
+	case 4:
+		config |= STEPCONFIG_YPP;
+		break;
+	case 5:
+		config |= STEPCONFIG_XPP | STEPCONFIG_INP_AN4 |
+				STEPCONFIG_XNP | STEPCONFIG_YPN;
+		break;
+	case 8:
+		config |= STEPCONFIG_YPP;
+		break;
+	}
+
+	for (i = (ts_dev->steps_to_configure + 1); i <= total_steps; i++) {
+		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
+		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+	}
+
+	config = 0;
+	/* Charge step configuration */
+	config = STEPCONFIG_XPP | STEPCONFIG_YNN |
+			STEPCHARGE_RFP_XPUL | STEPCHARGE_RFM_XNUR |
+			STEPCHARGE_INM_AN1 | STEPCHARGE_INP_AN1;
+
+	titsc_writel(ts_dev, REG_CHARGECONFIG, config);
+	titsc_writel(ts_dev, REG_CHARGEDELAY, CHARGEDLY_OPENDLY);
+
+	config = 0;
+	/* Configure to calculate pressure */
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_AVG_16 | STEPCONFIG_YPP |
+			STEPCONFIG_XNN | STEPCONFIG_INM_ADCREFM;
+	titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 1), config);
+	titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 1),
+			STEPCONFIG_OPENDLY);
+
+	config |= STEPCONFIG_INP_AN3 | STEPCONFIG_FIFO1;
+	titsc_writel(ts_dev, REG_STEPCONFIG(total_steps + 2), config);
+	titsc_writel(ts_dev, REG_STEPDELAY(total_steps + 2),
+			STEPCONFIG_OPENDLY);
+
+	titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
+}
+
+static void titsc_read_coordinates(struct titsc *ts_dev,
+				    unsigned int *x, unsigned int *y)
+{
+	unsigned int fifocount = titsc_readl(ts_dev, REG_FIFO0CNT);
+	unsigned int prev_val_x = ~0, prev_val_y = ~0;
+	unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
+	unsigned int read, diff;
+	unsigned int i, channel;
+
+	/*
+	 * Delta filter is used to remove large variations in sampled
+	 * values from ADC. The filter tries to predict where the next
+	 * coordinate could be. This is done by taking a previous
+	 * coordinate and subtracting it form current one. Further the
+	 * algorithm compares the difference with that of a present value,
+	 * if true the value is reported to the sub system.
+	 */
+	for (i = 0; i < fifocount - 1; i++) {
+		read = titsc_readl(ts_dev, REG_FIFO0);
+		channel = read & 0xf0000;
+		channel = channel >> 0x10;
+		if ((channel >= 0) && (channel < ts_dev->steps_to_configure)) {
+			read &= 0xfff;
+			diff = abs(read - prev_val_x);
+			if (diff < prev_diff_x) {
+				prev_diff_x = diff;
+				*x = read;
+			}
+			prev_val_x = read;
+		}
+
+		read = titsc_readl(ts_dev, REG_FIFO1);
+		channel = read & 0xf0000;
+		channel = channel >> 0x10;
+		if ((channel >= ts_dev->steps_to_configure) &&
+			(channel < (2 * ts_dev->steps_to_configure - 1))) {
+			read &= 0xfff;
+			diff = abs(read - prev_val_y);
+			if (diff < prev_diff_y) {
+				prev_diff_y = diff;
+				*y = read;
+			}
+			prev_val_y = read;
+		}
+	}
+}
+
+static irqreturn_t titsc_irq(int irq, void *dev)
+{
+	struct titsc *ts_dev = dev;
+	struct input_dev *input_dev = ts_dev->input;
+	unsigned int status, irqclr = 0;
+	unsigned int x = 0, y = 0;
+	unsigned int z1, z2, z;
+	unsigned int fsm;
+	unsigned int fifo1count, fifo0count;
+	int i;
+
+	status = titsc_readl(ts_dev, REG_IRQSTATUS);
+	if (status & IRQENB_FIFO0THRES) {
+		titsc_read_coordinates(ts_dev, &x, &y);
+
+		z1 = titsc_readl(ts_dev, REG_FIFO0) & 0xfff;
+		z2 = titsc_readl(ts_dev, REG_FIFO1) & 0xfff;
+
+		fifo1count = titsc_readl(ts_dev, REG_FIFO1CNT);
+		for (i = 0; i < fifo1count; i++)
+			titsc_readl(ts_dev, REG_FIFO1);
+
+		fifo0count = titsc_readl(ts_dev, REG_FIFO0CNT);
+		for (i = 0; i < fifo0count; i++)
+			titsc_readl(ts_dev, REG_FIFO0);
+
+		if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
+			/*
+			 * Calculate pressure using formula
+			 * Resistance(touch) = x plate resistance *
+			 * x postion/4096 * ((z2 / z1) - 1)
+			 */
+			z = z2 - z1;
+			z *= x;
+			z *= ts_dev->x_plate_resistance;
+			z /= z1;
+			z = (z + 2047) >> 12;
+
+			if (z <= MAX_12BIT) {
+				input_report_abs(input_dev, ABS_X, x);
+				input_report_abs(input_dev, ABS_Y, y);
+				input_report_abs(input_dev, ABS_PRESSURE, z);
+				input_report_key(input_dev, BTN_TOUCH, 1);
+				input_sync(input_dev);
+			}
+		}
+		irqclr |= IRQENB_FIFO0THRES;
+	}
+
+	/*
+	 * Time for sequencer to settle, to read
+	 * correct state of the sequencer.
+	 */
+	udelay(SEQ_SETTLE);
+
+	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
+	if (status & IRQENB_PENUP) {
+		/* Pen up event */
+		fsm = titsc_readl(ts_dev, REG_ADCFSM);
+		if (fsm == ADCFSM_STEPID) {
+			ts_dev->pen_down = false;
+			input_report_key(input_dev, BTN_TOUCH, 0);
+			input_report_abs(input_dev, ABS_PRESSURE, 0);
+			input_sync(input_dev);
+		} else {
+			ts_dev->pen_down = true;
+		}
+		irqclr |= IRQENB_PENUP;
+	}
+
+	titsc_writel(ts_dev, REG_IRQSTATUS, irqclr);
+
+	titsc_writel(ts_dev, REG_SE, STPENB_STEPENB_TC);
+	return IRQ_HANDLED;
+}
+
+/*
+ * The functions for inserting/removing driver as a module.
+ */
+
+static int __devinit titsc_probe(struct platform_device *pdev)
+{
+	struct titsc *ts_dev;
+	struct input_dev *input_dev;
+	struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+	struct mfd_tscadc_board	*pdata;
+	int err;
+
+	pdata = tscadc_dev->dev->platform_data;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "Could not find platform data\n");
+		return -EINVAL;
+	}
+
+	/* Allocate memory for device */
+	ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!ts_dev || !input_dev) {
+		dev_err(&pdev->dev, "failed to allocate memory.\n");
+		err = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	tscadc_dev->tsc = ts_dev;
+	ts_dev->mfd_tscadc = tscadc_dev;
+	ts_dev->input = input_dev;
+	ts_dev->irq = tscadc_dev->irq;
+	ts_dev->wires = pdata->tsc_init->wires;
+	ts_dev->x_plate_resistance = pdata->tsc_init->x_plate_resistance;
+	ts_dev->steps_to_configure = pdata->tsc_init->steps_to_configure;
+
+	err = request_irq(ts_dev->irq, titsc_irq,
+			  0, pdev->dev.driver->name, ts_dev);
+	if (err) {
+		dev_err(&pdev->dev, "failed to allocate irq.\n");
+		goto err_free_mem;
+	}
+
+	titsc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO0THRES);
+	titsc_step_config(ts_dev);
+	titsc_writel(ts_dev, REG_FIFO0THR, ts_dev->steps_to_configure);
+
+	input_dev->name = "ti-tsc";
+	input_dev->dev.parent = &pdev->dev;
+
+	input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+	input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+
+	input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(input_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
+
+	/* register to the input system */
+	err = input_register_device(input_dev);
+	if (err)
+		goto err_free_irq;
+
+	platform_set_drvdata(pdev, ts_dev);
+	return 0;
+
+err_free_irq:
+	free_irq(ts_dev->irq, ts_dev);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(ts_dev);
+	return err;
+}
+
+static int __devexit titsc_remove(struct platform_device *pdev)
+{
+	struct ti_tscadc_dev *tscadc_dev = pdev->dev.platform_data;
+	struct titsc *ts_dev = tscadc_dev->tsc;
+
+	free_irq(ts_dev->irq, ts_dev);
+
+	input_unregister_device(ts_dev->input);
+
+	platform_set_drvdata(pdev, NULL);
+	kfree(ts_dev);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int titsc_suspend(struct device *dev)
+{
+	struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+	struct titsc *ts_dev = tscadc_dev->tsc;
+	unsigned int idle;
+
+	if (device_may_wakeup(tscadc_dev->dev)) {
+		idle = titsc_readl(ts_dev, REG_IRQENABLE);
+		titsc_writel(ts_dev, REG_IRQENABLE,
+				(idle | IRQENB_HW_PEN));
+		titsc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
+	}
+	return 0;
+}
+
+static int titsc_resume(struct device *dev)
+{
+	struct ti_tscadc_dev *tscadc_dev = dev->platform_data;
+	struct titsc *ts_dev = tscadc_dev->tsc;
+
+	if (device_may_wakeup(tscadc_dev->dev)) {
+		titsc_writel(ts_dev, REG_IRQWAKEUP,
+				0x00);
+		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
+	}
+	titsc_step_config(ts_dev);
+	titsc_writel(ts_dev, REG_FIFO0THR,
+			ts_dev->steps_to_configure);
+	return 0;
+}
+
+static const struct dev_pm_ops titsc_pm_ops = {
+	.suspend = titsc_suspend,
+	.resume  = titsc_resume,
+};
+#define TITSC_PM_OPS (&titsc_pm_ops)
+#else
+#define TITSC_PM_OPS NULL
+#endif
+
+static struct platform_driver ti_tsc_driver = {
+	.probe	= titsc_probe,
+	.remove	= __devexit_p(titsc_remove),
+	.driver	= {
+		.name   = "tsc",
+		.owner	= THIS_MODULE,
+		.pm	= TITSC_PM_OPS,
+	},
+};
+module_platform_driver(ti_tsc_driver);
+
+MODULE_DESCRIPTION("TI touchscreen controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/ti_tscadc.c b/drivers/input/touchscreen/ti_tscadc.c
deleted file mode 100644
index d229c74..0000000
--- a/drivers/input/touchscreen/ti_tscadc.c
+++ /dev/null
@@ -1,486 +0,0 @@
-/*
- * TI Touch Screen driver
- *
- * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/err.h>
-#include <linux/module.h>
-#include <linux/input.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/input/ti_tscadc.h>
-#include <linux/delay.h>
-
-#define REG_IRQEOI		0x020
-#define REG_RAWIRQSTATUS	0x024
-#define REG_IRQSTATUS		0x028
-#define REG_IRQENABLE		0x02C
-#define REG_IRQWAKEUP		0x034
-#define REG_CTRL		0x040
-#define REG_ADCFSM		0x044
-#define REG_CLKDIV		0x04C
-#define REG_SE			0x054
-#define REG_IDLECONFIG		0x058
-#define REG_CHARGECONFIG	0x05C
-#define REG_CHARGEDELAY		0x060
-#define REG_STEPCONFIG(n)	(0x64 + ((n - 1) * 8))
-#define REG_STEPDELAY(n)	(0x68 + ((n - 1) * 8))
-#define REG_STEPCONFIG13	0x0C4
-#define REG_STEPDELAY13		0x0C8
-#define REG_STEPCONFIG14	0x0CC
-#define REG_STEPDELAY14		0x0D0
-#define REG_FIFO0CNT		0xE4
-#define REG_FIFO1THR		0xF4
-#define REG_FIFO0		0x100
-#define REG_FIFO1		0x200
-
-/*	Register Bitfields	*/
-#define IRQWKUP_ENB		BIT(0)
-#define STPENB_STEPENB		0x7FFF
-#define IRQENB_FIFO1THRES	BIT(5)
-#define IRQENB_PENUP		BIT(9)
-#define STEPCONFIG_MODE_HWSYNC	0x2
-#define STEPCONFIG_SAMPLES_AVG	(1 << 4)
-#define STEPCONFIG_XPP		(1 << 5)
-#define STEPCONFIG_XNN		(1 << 6)
-#define STEPCONFIG_YPP		(1 << 7)
-#define STEPCONFIG_YNN		(1 << 8)
-#define STEPCONFIG_XNP		(1 << 9)
-#define STEPCONFIG_YPN		(1 << 10)
-#define STEPCONFIG_INM		(1 << 18)
-#define STEPCONFIG_INP		(1 << 20)
-#define STEPCONFIG_INP_5	(1 << 21)
-#define STEPCONFIG_FIFO1	(1 << 26)
-#define STEPCONFIG_OPENDLY	0xff
-#define STEPCONFIG_Z1		(3 << 19)
-#define STEPIDLE_INP		(1 << 22)
-#define STEPCHARGE_RFP		(1 << 12)
-#define STEPCHARGE_INM		(1 << 15)
-#define STEPCHARGE_INP		(1 << 19)
-#define STEPCHARGE_RFM		(1 << 23)
-#define STEPCHARGE_DELAY	0x1
-#define CNTRLREG_TSCSSENB	(1 << 0)
-#define CNTRLREG_STEPID		(1 << 1)
-#define CNTRLREG_STEPCONFIGWRT	(1 << 2)
-#define CNTRLREG_4WIRE		(1 << 5)
-#define CNTRLREG_5WIRE		(1 << 6)
-#define CNTRLREG_8WIRE		(3 << 5)
-#define CNTRLREG_TSCENB		(1 << 7)
-#define ADCFSM_STEPID		0x10
-
-#define SEQ_SETTLE		275
-#define ADC_CLK			3000000
-#define MAX_12BIT		((1 << 12) - 1)
-#define TSCADC_DELTA_X		15
-#define TSCADC_DELTA_Y		15
-
-struct tscadc {
-	struct input_dev	*input;
-	struct clk		*tsc_ick;
-	void __iomem		*tsc_base;
-	unsigned int		irq;
-	unsigned int		wires;
-	unsigned int		x_plate_resistance;
-	bool			pen_down;
-};
-
-static unsigned int tscadc_readl(struct tscadc *ts, unsigned int reg)
-{
-	return readl(ts->tsc_base + reg);
-}
-
-static void tscadc_writel(struct tscadc *tsc, unsigned int reg,
-					unsigned int val)
-{
-	writel(val, tsc->tsc_base + reg);
-}
-
-static void tscadc_step_config(struct tscadc *ts_dev)
-{
-	unsigned int	config;
-	int i;
-
-	/* Configure the Step registers */
-
-	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_XPP;
-	switch (ts_dev->wires) {
-	case 4:
-		config |= STEPCONFIG_INP | STEPCONFIG_XNN;
-		break;
-	case 5:
-		config |= STEPCONFIG_YNN |
-				STEPCONFIG_INP_5 | STEPCONFIG_XNN |
-				STEPCONFIG_YPP;
-		break;
-	case 8:
-		config |= STEPCONFIG_INP | STEPCONFIG_XNN;
-		break;
-	}
-
-	for (i = 1; i < 7; i++) {
-		tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
-		tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
-	}
-
-	config = 0;
-	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_YNN |
-			STEPCONFIG_INM | STEPCONFIG_FIFO1;
-	switch (ts_dev->wires) {
-	case 4:
-		config |= STEPCONFIG_YPP;
-		break;
-	case 5:
-		config |= STEPCONFIG_XPP | STEPCONFIG_INP_5 |
-				STEPCONFIG_XNP | STEPCONFIG_YPN;
-		break;
-	case 8:
-		config |= STEPCONFIG_YPP;
-		break;
-	}
-
-	for (i = 7; i < 13; i++) {
-		tscadc_writel(ts_dev, REG_STEPCONFIG(i), config);
-		tscadc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
-	}
-
-	config = 0;
-	/* Charge step configuration */
-	config = STEPCONFIG_XPP | STEPCONFIG_YNN |
-			STEPCHARGE_RFP | STEPCHARGE_RFM |
-			STEPCHARGE_INM | STEPCHARGE_INP;
-
-	tscadc_writel(ts_dev, REG_CHARGECONFIG, config);
-	tscadc_writel(ts_dev, REG_CHARGEDELAY, STEPCHARGE_DELAY);
-
-	config = 0;
-	/* Configure to calculate pressure */
-	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_SAMPLES_AVG | STEPCONFIG_YPP |
-			STEPCONFIG_XNN | STEPCONFIG_INM;
-	tscadc_writel(ts_dev, REG_STEPCONFIG13, config);
-	tscadc_writel(ts_dev, REG_STEPDELAY13, STEPCONFIG_OPENDLY);
-
-	config |= STEPCONFIG_Z1 | STEPCONFIG_FIFO1;
-	tscadc_writel(ts_dev, REG_STEPCONFIG14, config);
-	tscadc_writel(ts_dev, REG_STEPDELAY14, STEPCONFIG_OPENDLY);
-
-	tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
-}
-
-static void tscadc_idle_config(struct tscadc *ts_config)
-{
-	unsigned int idleconfig;
-
-	idleconfig = STEPCONFIG_YNN |
-			STEPCONFIG_INM |
-			STEPCONFIG_YPN | STEPIDLE_INP;
-	tscadc_writel(ts_config, REG_IDLECONFIG, idleconfig);
-}
-
-static void tscadc_read_coordinates(struct tscadc *ts_dev,
-				    unsigned int *x, unsigned int *y)
-{
-	unsigned int fifocount = tscadc_readl(ts_dev, REG_FIFO0CNT);
-	unsigned int prev_val_x = ~0, prev_val_y = ~0;
-	unsigned int prev_diff_x = ~0, prev_diff_y = ~0;
-	unsigned int read, diff;
-	unsigned int i;
-
-	/*
-	 * Delta filter is used to remove large variations in sampled
-	 * values from ADC. The filter tries to predict where the next
-	 * coordinate could be. This is done by taking a previous
-	 * coordinate and subtracting it form current one. Further the
-	 * algorithm compares the difference with that of a present value,
-	 * if true the value is reported to the sub system.
-	 */
-	for (i = 0; i < fifocount - 1; i++) {
-		read = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
-		diff = abs(read - prev_val_x);
-		if (diff < prev_diff_x) {
-			prev_diff_x = diff;
-			*x = read;
-		}
-		prev_val_x = read;
-
-		read = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
-		diff = abs(read - prev_val_y);
-		if (diff < prev_diff_y) {
-			prev_diff_y = diff;
-			*y = read;
-		}
-		prev_val_y = read;
-	}
-}
-
-static irqreturn_t tscadc_irq(int irq, void *dev)
-{
-	struct tscadc *ts_dev = dev;
-	struct input_dev *input_dev = ts_dev->input;
-	unsigned int status, irqclr = 0;
-	unsigned int x = 0, y = 0;
-	unsigned int z1, z2, z;
-	unsigned int fsm;
-
-	status = tscadc_readl(ts_dev, REG_IRQSTATUS);
-	if (status & IRQENB_FIFO1THRES) {
-		tscadc_read_coordinates(ts_dev, &x, &y);
-
-		z1 = tscadc_readl(ts_dev, REG_FIFO0) & 0xfff;
-		z2 = tscadc_readl(ts_dev, REG_FIFO1) & 0xfff;
-
-		if (ts_dev->pen_down && z1 != 0 && z2 != 0) {
-			/*
-			 * Calculate pressure using formula
-			 * Resistance(touch) = x plate resistance *
-			 * x postion/4096 * ((z2 / z1) - 1)
-			 */
-			z = z2 - z1;
-			z *= x;
-			z *= ts_dev->x_plate_resistance;
-			z /= z1;
-			z = (z + 2047) >> 12;
-
-			if (z <= MAX_12BIT) {
-				input_report_abs(input_dev, ABS_X, x);
-				input_report_abs(input_dev, ABS_Y, y);
-				input_report_abs(input_dev, ABS_PRESSURE, z);
-				input_report_key(input_dev, BTN_TOUCH, 1);
-				input_sync(input_dev);
-			}
-		}
-		irqclr |= IRQENB_FIFO1THRES;
-	}
-
-	/*
-	 * Time for sequencer to settle, to read
-	 * correct state of the sequencer.
-	 */
-	udelay(SEQ_SETTLE);
-
-	status = tscadc_readl(ts_dev, REG_RAWIRQSTATUS);
-	if (status & IRQENB_PENUP) {
-		/* Pen up event */
-		fsm = tscadc_readl(ts_dev, REG_ADCFSM);
-		if (fsm == ADCFSM_STEPID) {
-			ts_dev->pen_down = false;
-			input_report_key(input_dev, BTN_TOUCH, 0);
-			input_report_abs(input_dev, ABS_PRESSURE, 0);
-			input_sync(input_dev);
-		} else {
-			ts_dev->pen_down = true;
-		}
-		irqclr |= IRQENB_PENUP;
-	}
-
-	tscadc_writel(ts_dev, REG_IRQSTATUS, irqclr);
-	/* check pending interrupts */
-	tscadc_writel(ts_dev, REG_IRQEOI, 0x0);
-
-	tscadc_writel(ts_dev, REG_SE, STPENB_STEPENB);
-	return IRQ_HANDLED;
-}
-
-/*
- * The functions for inserting/removing driver as a module.
- */
-
-static int __devinit tscadc_probe(struct platform_device *pdev)
-{
-	const struct tsc_data *pdata = pdev->dev.platform_data;
-	struct resource *res;
-	struct tscadc *ts_dev;
-	struct input_dev *input_dev;
-	struct clk *clk;
-	int err;
-	int clk_value, ctrl, irq;
-
-	if (!pdata) {
-		dev_err(&pdev->dev, "missing platform data.\n");
-		return -EINVAL;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(&pdev->dev, "no memory resource defined.\n");
-		return -EINVAL;
-	}
-
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		dev_err(&pdev->dev, "no irq ID is specified.\n");
-		return -EINVAL;
-	}
-
-	/* Allocate memory for device */
-	ts_dev = kzalloc(sizeof(struct tscadc), GFP_KERNEL);
-	input_dev = input_allocate_device();
-	if (!ts_dev || !input_dev) {
-		dev_err(&pdev->dev, "failed to allocate memory.\n");
-		err = -ENOMEM;
-		goto err_free_mem;
-	}
-
-	ts_dev->input = input_dev;
-	ts_dev->irq = irq;
-	ts_dev->wires = pdata->wires;
-	ts_dev->x_plate_resistance = pdata->x_plate_resistance;
-
-	res = request_mem_region(res->start, resource_size(res), pdev->name);
-	if (!res) {
-		dev_err(&pdev->dev, "failed to reserve registers.\n");
-		err = -EBUSY;
-		goto err_free_mem;
-	}
-
-	ts_dev->tsc_base = ioremap(res->start, resource_size(res));
-	if (!ts_dev->tsc_base) {
-		dev_err(&pdev->dev, "failed to map registers.\n");
-		err = -ENOMEM;
-		goto err_release_mem_region;
-	}
-
-	err = request_irq(ts_dev->irq, tscadc_irq,
-			  0, pdev->dev.driver->name, ts_dev);
-	if (err) {
-		dev_err(&pdev->dev, "failed to allocate irq.\n");
-		goto err_unmap_regs;
-	}
-
-	ts_dev->tsc_ick = clk_get(&pdev->dev, "adc_tsc_ick");
-	if (IS_ERR(ts_dev->tsc_ick)) {
-		dev_err(&pdev->dev, "failed to get TSC ick\n");
-		goto err_free_irq;
-	}
-	clk_enable(ts_dev->tsc_ick);
-
-	clk = clk_get(&pdev->dev, "adc_tsc_fck");
-	if (IS_ERR(clk)) {
-		dev_err(&pdev->dev, "failed to get TSC fck\n");
-		err = PTR_ERR(clk);
-		goto err_disable_clk;
-	}
-
-	clk_value = clk_get_rate(clk) / ADC_CLK;
-	clk_put(clk);
-
-	if (clk_value < 7) {
-		dev_err(&pdev->dev, "clock input less than min clock requirement\n");
-		goto err_disable_clk;
-	}
-	/* CLKDIV needs to be configured to the value minus 1 */
-	tscadc_writel(ts_dev, REG_CLKDIV, clk_value - 1);
-
-	 /* Enable wake-up of the SoC using touchscreen */
-	tscadc_writel(ts_dev, REG_IRQWAKEUP, IRQWKUP_ENB);
-
-	ctrl = CNTRLREG_STEPCONFIGWRT |
-			CNTRLREG_TSCENB |
-			CNTRLREG_STEPID;
-	switch (ts_dev->wires) {
-	case 4:
-		ctrl |= CNTRLREG_4WIRE;
-		break;
-	case 5:
-		ctrl |= CNTRLREG_5WIRE;
-		break;
-	case 8:
-		ctrl |= CNTRLREG_8WIRE;
-		break;
-	}
-	tscadc_writel(ts_dev, REG_CTRL, ctrl);
-
-	tscadc_idle_config(ts_dev);
-	tscadc_writel(ts_dev, REG_IRQENABLE, IRQENB_FIFO1THRES);
-	tscadc_step_config(ts_dev);
-	tscadc_writel(ts_dev, REG_FIFO1THR, 6);
-
-	ctrl |= CNTRLREG_TSCSSENB;
-	tscadc_writel(ts_dev, REG_CTRL, ctrl);
-
-	input_dev->name = "ti-tsc-adc";
-	input_dev->dev.parent = &pdev->dev;
-
-	input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
-	input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
-
-	input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
-	input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
-	input_set_abs_params(input_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
-
-	/* register to the input system */
-	err = input_register_device(input_dev);
-	if (err)
-		goto err_disable_clk;
-
-	platform_set_drvdata(pdev, ts_dev);
-	return 0;
-
-err_disable_clk:
-	clk_disable(ts_dev->tsc_ick);
-	clk_put(ts_dev->tsc_ick);
-err_free_irq:
-	free_irq(ts_dev->irq, ts_dev);
-err_unmap_regs:
-	iounmap(ts_dev->tsc_base);
-err_release_mem_region:
-	release_mem_region(res->start, resource_size(res));
-err_free_mem:
-	input_free_device(input_dev);
-	kfree(ts_dev);
-	return err;
-}
-
-static int __devexit tscadc_remove(struct platform_device *pdev)
-{
-	struct tscadc *ts_dev = platform_get_drvdata(pdev);
-	struct resource *res;
-
-	free_irq(ts_dev->irq, ts_dev);
-
-	input_unregister_device(ts_dev->input);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	iounmap(ts_dev->tsc_base);
-	release_mem_region(res->start, resource_size(res));
-
-	clk_disable(ts_dev->tsc_ick);
-	clk_put(ts_dev->tsc_ick);
-
-	kfree(ts_dev);
-
-	platform_set_drvdata(pdev, NULL);
-	return 0;
-}
-
-static struct platform_driver ti_tsc_driver = {
-	.probe	= tscadc_probe,
-	.remove	= __devexit_p(tscadc_remove),
-	.driver	= {
-		.name   = "tsc",
-		.owner	= THIS_MODULE,
-	},
-};
-module_platform_driver(ti_tsc_driver);
-
-MODULE_DESCRIPTION("TI touchscreen controller driver");
-MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
-MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b63987c..1c0abd4 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -104,6 +104,17 @@
 	  To compile this driver as a module, choose M here: the
 	  module will be called ti-ssp.
 
+config MFD_TI_AM335X_TSCADC
+	tristate "TI ADC / Touch Screen chip support"
+	select MFD_CORE
+	select REGMAP
+	select REGMAP_MMIO
+	help
+	  If you say yes here you get support for Texas Instruments series
+	  of Touch Screen /ADC chips.
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti_am335x_tscadc.
+
 config HTC_EGPIO
 	bool "HTC EGPIO support"
 	depends on GENERIC_HARDIRQS && GPIOLIB && ARM
@@ -253,6 +264,20 @@
 	  If you say yes here you get support for the TPS65912 series of
 	  PM chips with SPI interface.
 
+config MFD_TPS80031
+	bool "TI TPS80031/TPS80032 Power Management chips"
+	depends on I2C=y && GENERIC_HARDIRQS
+	select MFD_CORE
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	help
+	  If you say yes here you get support for the Texas Instruments
+	  TPS80031/ TPS80032 Fully Integrated Power Management with Power
+	  Path and Battery Charger. The device provides five configurable
+	  step-down converters, 11 general purpose LDOs, USB OTG Module,
+	  ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with
+	  Power Path from USB, 32K clock generator.
+
 config MENELAUS
 	bool "Texas Instruments TWL92330/Menelaus PM chip"
 	depends on I2C=y && ARCH_OMAP2
@@ -309,10 +334,10 @@
 
 config TWL6040_CORE
 	bool "Support for TWL6040 audio codec"
-	depends on I2C=y && GENERIC_HARDIRQS
+	depends on I2C=y
 	select MFD_CORE
 	select REGMAP_I2C
-	select IRQ_DOMAIN
+	select REGMAP_IRQ
 	default n
 	help
 	  Say yes here if you want support for Texas Instruments TWL6040 audio
@@ -990,6 +1015,7 @@
 	depends on I2C=y && GENERIC_HARDIRQS
 	select MFD_CORE
 	select REGMAP_I2C
+	select REGMAP_IRQ
 	help
 	  If you say yes here you get support for the TPS65090 series of
 	  Power Management chips.
@@ -1034,6 +1060,7 @@
 	bool "STA2X11 multi function device support"
 	depends on STA2X11
 	select MFD_CORE
+	select REGMAP_MMIO
 
 config MFD_SYSCON
 	bool "System Controller Register R/W Based on Regmap"
@@ -1053,6 +1080,38 @@
 	  If you say yes here you get support for the Palmas
 	  series of PMIC chips from Texas Instruments.
 
+config MFD_VIPERBOARD
+        tristate "Support for Nano River Technologies Viperboard"
+	select MFD_CORE
+	depends on USB
+	default n
+	help
+	  Say yes here if you want support for Nano River Technologies
+	  Viperboard.
+	  There are mfd cell drivers available for i2c master, adc and
+	  both gpios found on the board. The spi part does not yet
+	  have a driver.
+	  You need to select the mfd cell drivers separately.
+	  The drivers do not support all features the board exposes.
+
+config MFD_RETU
+	tristate "Support for Retu multi-function device"
+	select MFD_CORE
+	depends on I2C
+	select REGMAP_IRQ
+	help
+	  Retu is a multi-function device found on Nokia Internet Tablets
+	  (770, N800 and N810).
+
+config MFD_AS3711
+	bool "Support for AS3711"
+	select MFD_CORE
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	depends on I2C=y
+	help
+	  Support for the AS3711 PMIC from AMS
+
 endmenu
 endif
 
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 69f260a..8b977f8 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -19,6 +19,7 @@
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
 obj-$(CONFIG_MFD_TI_SSP)	+= ti-ssp.o
+obj-$(CONFIG_MFD_TI_AM335X_TSCADC)	+= ti_am335x_tscadc.o
 
 obj-$(CONFIG_MFD_STA2X11)	+= sta2x11-mfd.o
 obj-$(CONFIG_MFD_STMPE)		+= stmpe.o
@@ -55,18 +56,19 @@
 obj-$(CONFIG_TPS65010)		+= tps65010.o
 obj-$(CONFIG_TPS6507X)		+= tps6507x.o
 obj-$(CONFIG_MFD_TPS65217)	+= tps65217.o
-obj-$(CONFIG_MFD_TPS65910)	+= tps65910.o tps65910-irq.o
+obj-$(CONFIG_MFD_TPS65910)	+= tps65910.o
 tps65912-objs                   := tps65912-core.o tps65912-irq.o
 obj-$(CONFIG_MFD_TPS65912)	+= tps65912.o
 obj-$(CONFIG_MFD_TPS65912_I2C)	+= tps65912-i2c.o
 obj-$(CONFIG_MFD_TPS65912_SPI)  += tps65912-spi.o
+obj-$(CONFIG_MFD_TPS80031)	+= tps80031.o
 obj-$(CONFIG_MENELAUS)		+= menelaus.o
 
 obj-$(CONFIG_TWL4030_CORE)	+= twl-core.o twl4030-irq.o twl6030-irq.o
 obj-$(CONFIG_TWL4030_MADC)      += twl4030-madc.o
 obj-$(CONFIG_TWL4030_POWER)    += twl4030-power.o
 obj-$(CONFIG_MFD_TWL4030_AUDIO)	+= twl4030-audio.o
-obj-$(CONFIG_TWL6040_CORE)	+= twl6040-core.o twl6040-irq.o
+obj-$(CONFIG_TWL6040_CORE)	+= twl6040.o
 
 obj-$(CONFIG_MFD_MC13XXX)	+= mc13xxx-core.o
 obj-$(CONFIG_MFD_MC13XXX_SPI)	+= mc13xxx-spi.o
@@ -89,6 +91,7 @@
 
 obj-$(CONFIG_PMIC_DA903X)	+= da903x.o
 
+obj-$(CONFIG_PMIC_DA9052)	+= da9052-irq.o
 obj-$(CONFIG_PMIC_DA9052)	+= da9052-core.o
 obj-$(CONFIG_MFD_DA9052_SPI)	+= da9052-spi.o
 obj-$(CONFIG_MFD_DA9052_I2C)	+= da9052-i2c.o
@@ -137,8 +140,11 @@
 obj-$(CONFIG_MFD_AAT2870_CORE)	+= aat2870-core.o
 obj-$(CONFIG_MFD_INTEL_MSIC)	+= intel_msic.o
 obj-$(CONFIG_MFD_PALMAS)	+= palmas.o
+obj-$(CONFIG_MFD_VIPERBOARD)    += viperboard.o
 obj-$(CONFIG_MFD_RC5T583)	+= rc5t583.o rc5t583-irq.o
 obj-$(CONFIG_MFD_SEC_CORE)	+= sec-core.o sec-irq.o
 obj-$(CONFIG_MFD_SYSCON)	+= syscon.o
 obj-$(CONFIG_MFD_LM3533)	+= lm3533-core.o lm3533-ctrlbank.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o vexpress-sysreg.o
+obj-$(CONFIG_MFD_RETU)		+= retu-mfd.o
+obj-$(CONFIG_MFD_AS3711)	+= as3711.o
diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c
index 59da165..e1650ba 100644
--- a/drivers/mfd/ab8500-core.c
+++ b/drivers/mfd/ab8500-core.c
@@ -586,38 +586,6 @@
 		return 0;
 }
 
-/* AB8500 GPIO Resources */
-static struct resource __devinitdata ab8500_gpio_resources[] = {
-	{
-		.name	= "GPIO_INT6",
-		.start	= AB8500_INT_GPIO6R,
-		.end	= AB8500_INT_GPIO41F,
-		.flags	= IORESOURCE_IRQ,
-	}
-};
-
-/* AB9540 GPIO Resources */
-static struct resource __devinitdata ab9540_gpio_resources[] = {
-	{
-		.name	= "GPIO_INT6",
-		.start	= AB8500_INT_GPIO6R,
-		.end	= AB8500_INT_GPIO41F,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= "GPIO_INT14",
-		.start	= AB9540_INT_GPIO50R,
-		.end	= AB9540_INT_GPIO54R,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= "GPIO_INT15",
-		.start	= AB9540_INT_GPIO50F,
-		.end	= AB9540_INT_GPIO54F,
-		.flags	= IORESOURCE_IRQ,
-	}
-};
-
 static struct resource ab8500_gpadc_resources[] = {
 	{
 		.name	= "HW_CONV_END",
@@ -979,6 +947,10 @@
 		.of_compatible = "stericsson,ab8500-regulator",
 	},
 	{
+		.name = "abx500-clk",
+		.of_compatible = "stericsson,abx500-clk",
+	},
+	{
 		.name = "ab8500-gpadc",
 		.of_compatible = "stericsson,ab8500-gpadc",
 		.num_resources = ARRAY_SIZE(ab8500_gpadc_resources),
@@ -1080,8 +1052,6 @@
 	{
 		.name = "ab8500-gpio",
 		.of_compatible = "stericsson,ab8500-gpio",
-		.num_resources = ARRAY_SIZE(ab8500_gpio_resources),
-		.resources = ab8500_gpio_resources,
 	},
 	{
 		.name = "ab8500-usb",
@@ -1098,8 +1068,6 @@
 static struct mfd_cell ab9540_devs[] = {
 	{
 		.name = "ab8500-gpio",
-		.num_resources = ARRAY_SIZE(ab9540_gpio_resources),
-		.resources = ab9540_gpio_resources,
 	},
 	{
 		.name = "ab9540-usb",
@@ -1284,7 +1252,7 @@
 	int i;
 	u8 value;
 
-	ab8500 = kzalloc(sizeof *ab8500, GFP_KERNEL);
+	ab8500 = devm_kzalloc(&pdev->dev, sizeof *ab8500, GFP_KERNEL);
 	if (!ab8500)
 		return -ENOMEM;
 
@@ -1294,10 +1262,8 @@
 	ab8500->dev = &pdev->dev;
 
 	resource = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-	if (!resource) {
-		ret = -ENODEV;
-		goto out_free_ab8500;
-	}
+	if (!resource)
+		return -ENODEV;
 
 	ab8500->irq = resource->start;
 
@@ -1320,7 +1286,7 @@
 		ret = get_register_interruptible(ab8500, AB8500_MISC,
 			AB8500_IC_NAME_REG, &value);
 		if (ret < 0)
-			goto out_free_ab8500;
+			return ret;
 
 		ab8500->version = value;
 	}
@@ -1328,7 +1294,7 @@
 	ret = get_register_interruptible(ab8500, AB8500_MISC,
 		AB8500_REV_REG, &value);
 	if (ret < 0)
-		goto out_free_ab8500;
+		return ret;
 
 	ab8500->chip_id = value;
 
@@ -1345,14 +1311,13 @@
 		ab8500->mask_size = AB8500_NUM_IRQ_REGS;
 		ab8500->irq_reg_offset = ab8500_irq_regoffset;
 	}
-	ab8500->mask = kzalloc(ab8500->mask_size, GFP_KERNEL);
+	ab8500->mask = devm_kzalloc(&pdev->dev, ab8500->mask_size, GFP_KERNEL);
 	if (!ab8500->mask)
 		return -ENOMEM;
-	ab8500->oldmask = kzalloc(ab8500->mask_size, GFP_KERNEL);
-	if (!ab8500->oldmask) {
-		ret = -ENOMEM;
-		goto out_freemask;
-	}
+	ab8500->oldmask = devm_kzalloc(&pdev->dev, ab8500->mask_size, GFP_KERNEL);
+	if (!ab8500->oldmask)
+		return -ENOMEM;
+
 	/*
 	 * ab8500 has switched off due to (SWITCH_OFF_STATUS):
 	 * 0x01 Swoff bit programming
@@ -1406,37 +1371,37 @@
 
 	ret = abx500_register_ops(ab8500->dev, &ab8500_ops);
 	if (ret)
-		goto out_freeoldmask;
+		return ret;
 
 	for (i = 0; i < ab8500->mask_size; i++)
 		ab8500->mask[i] = ab8500->oldmask[i] = 0xff;
 
 	ret = ab8500_irq_init(ab8500, np);
 	if (ret)
-		goto out_freeoldmask;
+		return ret;
 
 	/*  Activate this feature only in ab9540 */
 	/*  till tests are done on ab8500 1p2 or later*/
 	if (is_ab9540(ab8500)) {
-		ret = request_threaded_irq(ab8500->irq, NULL,
-					ab8500_hierarchical_irq,
-					IRQF_ONESHOT | IRQF_NO_SUSPEND,
-					"ab8500", ab8500);
+		ret = devm_request_threaded_irq(&pdev->dev, ab8500->irq, NULL,
+						ab8500_hierarchical_irq,
+						IRQF_ONESHOT | IRQF_NO_SUSPEND,
+						"ab8500", ab8500);
 	}
 	else {
-		ret = request_threaded_irq(ab8500->irq, NULL,
-					ab8500_irq,
-					IRQF_ONESHOT | IRQF_NO_SUSPEND,
-					"ab8500", ab8500);
+		ret = devm_request_threaded_irq(&pdev->dev, ab8500->irq, NULL,
+						ab8500_irq,
+						IRQF_ONESHOT | IRQF_NO_SUSPEND,
+						"ab8500", ab8500);
 		if (ret)
-			goto out_freeoldmask;
+			return ret;
 	}
 
 	ret = mfd_add_devices(ab8500->dev, 0, abx500_common_devs,
 			ARRAY_SIZE(abx500_common_devs), NULL,
 			ab8500->irq_base, ab8500->domain);
 	if (ret)
-		goto out_freeirq;
+		return ret;
 
 	if (is_ab9540(ab8500))
 		ret = mfd_add_devices(ab8500->dev, 0, ab9540_devs,
@@ -1447,14 +1412,14 @@
 				ARRAY_SIZE(ab8500_devs), NULL,
 				ab8500->irq_base, ab8500->domain);
 	if (ret)
-		goto out_freeirq;
+		return ret;
 
 	if (is_ab9540(ab8500) || is_ab8505(ab8500))
 		ret = mfd_add_devices(ab8500->dev, 0, ab9540_ab8505_devs,
 				ARRAY_SIZE(ab9540_ab8505_devs), NULL,
 				ab8500->irq_base, ab8500->domain);
 	if (ret)
-		goto out_freeirq;
+		return ret;
 
 	if (!no_bm) {
 		/* Add battery management devices */
@@ -1475,17 +1440,6 @@
 		dev_err(ab8500->dev, "error creating sysfs entries\n");
 
 	return ret;
-
-out_freeirq:
-	free_irq(ab8500->irq, ab8500);
-out_freeoldmask:
-	kfree(ab8500->oldmask);
-out_freemask:
-	kfree(ab8500->mask);
-out_free_ab8500:
-	kfree(ab8500);
-
-	return ret;
 }
 
 static int ab8500_remove(struct platform_device *pdev)
@@ -1498,11 +1452,6 @@
 		sysfs_remove_group(&ab8500->dev->kobj, &ab8500_attr_group);
 
 	mfd_remove_devices(ab8500->dev);
-	free_irq(ab8500->irq, ab8500);
-
-	kfree(ab8500->oldmask);
-	kfree(ab8500->mask);
-	kfree(ab8500);
 
 	return 0;
 }
diff --git a/drivers/mfd/arizona-core.c b/drivers/mfd/arizona-core.c
index c784f46..bc8a3ed 100644
--- a/drivers/mfd/arizona-core.c
+++ b/drivers/mfd/arizona-core.c
@@ -292,6 +292,7 @@
 	struct device *dev = arizona->dev;
 	const char *type_name;
 	unsigned int reg, val;
+	int (*apply_patch)(struct arizona *) = NULL;
 	int ret, i;
 
 	dev_set_drvdata(arizona->dev, arizona);
@@ -391,7 +392,7 @@
 				arizona->type);
 			arizona->type = WM5102;
 		}
-		ret = wm5102_patch(arizona);
+		apply_patch = wm5102_patch;
 		break;
 #endif
 #ifdef CONFIG_MFD_WM5110
@@ -402,7 +403,7 @@
 				arizona->type);
 			arizona->type = WM5110;
 		}
-		ret = wm5110_patch(arizona);
+		apply_patch = wm5110_patch;
 		break;
 #endif
 	default:
@@ -412,9 +413,6 @@
 
 	dev_info(dev, "%s revision %c\n", type_name, arizona->rev + 'A');
 
-	if (ret != 0)
-		dev_err(arizona->dev, "Failed to apply patch: %d\n", ret);
-
 	/* If we have a /RESET GPIO we'll already be reset */
 	if (!arizona->pdata.reset) {
 		regcache_mark_dirty(arizona->regmap);
@@ -438,6 +436,15 @@
 		goto err_reset;
 	}
 
+	if (apply_patch) {
+		ret = apply_patch(arizona);
+		if (ret != 0) {
+			dev_err(arizona->dev, "Failed to apply patch: %d\n",
+				ret);
+			goto err_reset;
+		}
+	}
+
 	for (i = 0; i < ARRAY_SIZE(arizona->pdata.gpio_defaults); i++) {
 		if (!arizona->pdata.gpio_defaults[i])
 			continue;
diff --git a/drivers/mfd/arizona-irq.c b/drivers/mfd/arizona-irq.c
index b1b0091..74713bf 100644
--- a/drivers/mfd/arizona-irq.c
+++ b/drivers/mfd/arizona-irq.c
@@ -224,6 +224,7 @@
 	arizona->virq = irq_domain_add_linear(NULL, 2, &arizona_domain_ops,
 					      arizona);
 	if (!arizona->virq) {
+		dev_err(arizona->dev, "Failed to add core IRQ domain\n");
 		ret = -EINVAL;
 		goto err;
 	}
diff --git a/drivers/mfd/as3711.c b/drivers/mfd/as3711.c
new file mode 100644
index 0000000..e994c96
--- /dev/null
+++ b/drivers/mfd/as3711.c
@@ -0,0 +1,217 @@
+/*
+ * AS3711 PMIC MFC driver
+ *
+ * Copyright (C) 2012 Renesas Electronics Corporation
+ * Author: Guennadi Liakhovetski, <g.liakhovetski@gmx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mfd/as3711.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+enum {
+	AS3711_REGULATOR,
+	AS3711_BACKLIGHT,
+};
+
+/*
+ * Ok to have it static: it is only used during probing and multiple I2C devices
+ * cannot be probed simultaneously. Just make sure to avoid stale data.
+ */
+static struct mfd_cell as3711_subdevs[] = {
+	[AS3711_REGULATOR] = {.name = "as3711-regulator",},
+	[AS3711_BACKLIGHT] = {.name = "as3711-backlight",},
+};
+
+static bool as3711_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case AS3711_GPIO_SIGNAL_IN:
+	case AS3711_INTERRUPT_STATUS_1:
+	case AS3711_INTERRUPT_STATUS_2:
+	case AS3711_INTERRUPT_STATUS_3:
+	case AS3711_CHARGER_STATUS_1:
+	case AS3711_CHARGER_STATUS_2:
+	case AS3711_REG_STATUS:
+		return true;
+	}
+	return false;
+}
+
+static bool as3711_precious_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case AS3711_INTERRUPT_STATUS_1:
+	case AS3711_INTERRUPT_STATUS_2:
+	case AS3711_INTERRUPT_STATUS_3:
+		return true;
+	}
+	return false;
+}
+
+static bool as3711_readable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case AS3711_SD_1_VOLTAGE:
+	case AS3711_SD_2_VOLTAGE:
+	case AS3711_SD_3_VOLTAGE:
+	case AS3711_SD_4_VOLTAGE:
+	case AS3711_LDO_1_VOLTAGE:
+	case AS3711_LDO_2_VOLTAGE:
+	case AS3711_LDO_3_VOLTAGE:
+	case AS3711_LDO_4_VOLTAGE:
+	case AS3711_LDO_5_VOLTAGE:
+	case AS3711_LDO_6_VOLTAGE:
+	case AS3711_LDO_7_VOLTAGE:
+	case AS3711_LDO_8_VOLTAGE:
+	case AS3711_SD_CONTROL:
+	case AS3711_GPIO_SIGNAL_OUT:
+	case AS3711_GPIO_SIGNAL_IN:
+	case AS3711_SD_CONTROL_1:
+	case AS3711_SD_CONTROL_2:
+	case AS3711_CURR_CONTROL:
+	case AS3711_CURR1_VALUE:
+	case AS3711_CURR2_VALUE:
+	case AS3711_CURR3_VALUE:
+	case AS3711_STEPUP_CONTROL_1:
+	case AS3711_STEPUP_CONTROL_2:
+	case AS3711_STEPUP_CONTROL_4:
+	case AS3711_STEPUP_CONTROL_5:
+	case AS3711_REG_STATUS:
+	case AS3711_INTERRUPT_STATUS_1:
+	case AS3711_INTERRUPT_STATUS_2:
+	case AS3711_INTERRUPT_STATUS_3:
+	case AS3711_CHARGER_STATUS_1:
+	case AS3711_CHARGER_STATUS_2:
+	case AS3711_ASIC_ID_1:
+	case AS3711_ASIC_ID_2:
+		return true;
+	}
+	return false;
+}
+
+static const struct regmap_config as3711_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.volatile_reg = as3711_volatile_reg,
+	.readable_reg = as3711_readable_reg,
+	.precious_reg = as3711_precious_reg,
+	.max_register = AS3711_MAX_REGS,
+	.num_reg_defaults_raw = AS3711_MAX_REGS,
+	.cache_type = REGCACHE_RBTREE,
+};
+
+static int as3711_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct as3711 *as3711;
+	struct as3711_platform_data *pdata = client->dev.platform_data;
+	unsigned int id1, id2;
+	int ret;
+
+	if (!pdata)
+		dev_dbg(&client->dev, "Platform data not found\n");
+
+	as3711 = devm_kzalloc(&client->dev, sizeof(struct as3711), GFP_KERNEL);
+	if (!as3711) {
+		dev_err(&client->dev, "Memory allocation failed\n");
+		return -ENOMEM;
+	}
+
+	as3711->dev = &client->dev;
+	i2c_set_clientdata(client, as3711);
+
+	if (client->irq)
+		dev_notice(&client->dev, "IRQ not supported yet\n");
+
+	as3711->regmap = devm_regmap_init_i2c(client, &as3711_regmap_config);
+	if (IS_ERR(as3711->regmap)) {
+		ret = PTR_ERR(as3711->regmap);
+		dev_err(&client->dev, "regmap initialization failed: %d\n", ret);
+		return ret;
+	}
+
+	ret = regmap_read(as3711->regmap, AS3711_ASIC_ID_1, &id1);
+	if (!ret)
+		ret = regmap_read(as3711->regmap, AS3711_ASIC_ID_2, &id2);
+	if (ret < 0) {
+		dev_err(&client->dev, "regmap_read() failed: %d\n", ret);
+		return ret;
+	}
+	if (id1 != 0x8b)
+		return -ENODEV;
+	dev_info(as3711->dev, "AS3711 detected: %x:%x\n", id1, id2);
+
+	/* We can reuse as3711_subdevs[], it will be copied in mfd_add_devices() */
+	if (pdata) {
+		as3711_subdevs[AS3711_REGULATOR].platform_data = &pdata->regulator;
+		as3711_subdevs[AS3711_REGULATOR].pdata_size = sizeof(pdata->regulator);
+		as3711_subdevs[AS3711_BACKLIGHT].platform_data = &pdata->backlight;
+		as3711_subdevs[AS3711_BACKLIGHT].pdata_size = sizeof(pdata->backlight);
+	} else {
+		as3711_subdevs[AS3711_REGULATOR].platform_data = NULL;
+		as3711_subdevs[AS3711_REGULATOR].pdata_size = 0;
+		as3711_subdevs[AS3711_BACKLIGHT].platform_data = NULL;
+		as3711_subdevs[AS3711_BACKLIGHT].pdata_size = 0;
+	}
+
+	ret = mfd_add_devices(as3711->dev, -1, as3711_subdevs,
+			      ARRAY_SIZE(as3711_subdevs), NULL, 0, NULL);
+	if (ret < 0)
+		dev_err(&client->dev, "add mfd devices failed: %d\n", ret);
+
+	return ret;
+}
+
+static int as3711_i2c_remove(struct i2c_client *client)
+{
+	struct as3711 *as3711 = i2c_get_clientdata(client);
+
+	mfd_remove_devices(as3711->dev);
+	return 0;
+}
+
+static const struct i2c_device_id as3711_i2c_id[] = {
+	{.name = "as3711", .driver_data = 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, as3711_i2c_id);
+
+static struct i2c_driver as3711_i2c_driver = {
+	.driver = {
+		   .name = "as3711",
+		   .owner = THIS_MODULE,
+		   },
+	.probe = as3711_i2c_probe,
+	.remove = as3711_i2c_remove,
+	.id_table = as3711_i2c_id,
+};
+
+static int __init as3711_i2c_init(void)
+{
+	return i2c_add_driver(&as3711_i2c_driver);
+}
+/* Initialise early */
+subsys_initcall(as3711_i2c_init);
+
+static void __exit as3711_i2c_exit(void)
+{
+	i2c_del_driver(&as3711_i2c_driver);
+}
+module_exit(as3711_i2c_exit);
+
+MODULE_AUTHOR("Guennadi Liakhovetski <g.liakhovetski@gmx.de>");
+MODULE_DESCRIPTION("AS3711 PMIC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/da9052-core.c b/drivers/mfd/da9052-core.c
index 689b747..a3c9613 100644
--- a/drivers/mfd/da9052-core.c
+++ b/drivers/mfd/da9052-core.c
@@ -15,7 +15,6 @@
 #include <linux/delay.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
-#include <linux/irq.h>
 #include <linux/mfd/core.h>
 #include <linux/slab.h>
 #include <linux/module.h>
@@ -24,16 +23,6 @@
 #include <linux/mfd/da9052/pdata.h>
 #include <linux/mfd/da9052/reg.h>
 
-#define DA9052_NUM_IRQ_REGS		4
-#define DA9052_IRQ_MASK_POS_1		0x01
-#define DA9052_IRQ_MASK_POS_2		0x02
-#define DA9052_IRQ_MASK_POS_3		0x04
-#define DA9052_IRQ_MASK_POS_4		0x08
-#define DA9052_IRQ_MASK_POS_5		0x10
-#define DA9052_IRQ_MASK_POS_6		0x20
-#define DA9052_IRQ_MASK_POS_7		0x40
-#define DA9052_IRQ_MASK_POS_8		0x80
-
 static bool da9052_reg_readable(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
@@ -425,15 +414,6 @@
 }
 EXPORT_SYMBOL_GPL(da9052_adc_manual_read);
 
-static irqreturn_t da9052_auxadc_irq(int irq, void *irq_data)
-{
-	struct da9052 *da9052 = irq_data;
-
-	complete(&da9052->done);
-
-	return IRQ_HANDLED;
-}
-
 int da9052_adc_read_temp(struct da9052 *da9052)
 {
 	int tbat;
@@ -447,74 +427,6 @@
 }
 EXPORT_SYMBOL_GPL(da9052_adc_read_temp);
 
-static struct resource da9052_rtc_resource = {
-	.name = "ALM",
-	.start = DA9052_IRQ_ALARM,
-	.end   = DA9052_IRQ_ALARM,
-	.flags = IORESOURCE_IRQ,
-};
-
-static struct resource da9052_onkey_resource = {
-	.name = "ONKEY",
-	.start = DA9052_IRQ_NONKEY,
-	.end   = DA9052_IRQ_NONKEY,
-	.flags = IORESOURCE_IRQ,
-};
-
-static struct resource da9052_bat_resources[] = {
-	{
-		.name = "BATT TEMP",
-		.start = DA9052_IRQ_TBAT,
-		.end   = DA9052_IRQ_TBAT,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "DCIN DET",
-		.start = DA9052_IRQ_DCIN,
-		.end   = DA9052_IRQ_DCIN,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "DCIN REM",
-		.start = DA9052_IRQ_DCINREM,
-		.end   = DA9052_IRQ_DCINREM,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "VBUS DET",
-		.start = DA9052_IRQ_VBUS,
-		.end   = DA9052_IRQ_VBUS,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "VBUS REM",
-		.start = DA9052_IRQ_VBUSREM,
-		.end   = DA9052_IRQ_VBUSREM,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "CHG END",
-		.start = DA9052_IRQ_CHGEND,
-		.end   = DA9052_IRQ_CHGEND,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct resource da9052_tsi_resources[] = {
-	{
-		.name = "PENDWN",
-		.start = DA9052_IRQ_PENDOWN,
-		.end   = DA9052_IRQ_PENDOWN,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.name = "TSIRDY",
-		.start = DA9052_IRQ_TSIREADY,
-		.end   = DA9052_IRQ_TSIREADY,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
 static struct mfd_cell da9052_subdev_info[] = {
 	{
 		.name = "da9052-regulator",
@@ -574,13 +486,9 @@
 	},
 	{
 		.name = "da9052-onkey",
-		.resources = &da9052_onkey_resource,
-		.num_resources = 1,
 	},
 	{
 		.name = "da9052-rtc",
-		.resources = &da9052_rtc_resource,
-		.num_resources = 1,
 	},
 	{
 		.name = "da9052-gpio",
@@ -602,160 +510,15 @@
 	},
 	{
 		.name = "da9052-tsi",
-		.resources = da9052_tsi_resources,
-		.num_resources = ARRAY_SIZE(da9052_tsi_resources),
 	},
 	{
 		.name = "da9052-bat",
-		.resources = da9052_bat_resources,
-		.num_resources = ARRAY_SIZE(da9052_bat_resources),
 	},
 	{
 		.name = "da9052-watchdog",
 	},
 };
 
-static struct regmap_irq da9052_irqs[] = {
-	[DA9052_IRQ_DCIN] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_1,
-	},
-	[DA9052_IRQ_VBUS] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_2,
-	},
-	[DA9052_IRQ_DCINREM] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_3,
-	},
-	[DA9052_IRQ_VBUSREM] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_4,
-	},
-	[DA9052_IRQ_VDDLOW] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_5,
-	},
-	[DA9052_IRQ_ALARM] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_6,
-	},
-	[DA9052_IRQ_SEQRDY] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_7,
-	},
-	[DA9052_IRQ_COMP1V2] = {
-		.reg_offset = 0,
-		.mask = DA9052_IRQ_MASK_POS_8,
-	},
-	[DA9052_IRQ_NONKEY] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_1,
-	},
-	[DA9052_IRQ_IDFLOAT] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_2,
-	},
-	[DA9052_IRQ_IDGND] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_3,
-	},
-	[DA9052_IRQ_CHGEND] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_4,
-	},
-	[DA9052_IRQ_TBAT] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_5,
-	},
-	[DA9052_IRQ_ADC_EOM] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_6,
-	},
-	[DA9052_IRQ_PENDOWN] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_7,
-	},
-	[DA9052_IRQ_TSIREADY] = {
-		.reg_offset = 1,
-		.mask = DA9052_IRQ_MASK_POS_8,
-	},
-	[DA9052_IRQ_GPI0] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_1,
-	},
-	[DA9052_IRQ_GPI1] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_2,
-	},
-	[DA9052_IRQ_GPI2] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_3,
-	},
-	[DA9052_IRQ_GPI3] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_4,
-	},
-	[DA9052_IRQ_GPI4] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_5,
-	},
-	[DA9052_IRQ_GPI5] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_6,
-	},
-	[DA9052_IRQ_GPI6] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_7,
-	},
-	[DA9052_IRQ_GPI7] = {
-		.reg_offset = 2,
-		.mask = DA9052_IRQ_MASK_POS_8,
-	},
-	[DA9052_IRQ_GPI8] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_1,
-	},
-	[DA9052_IRQ_GPI9] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_2,
-	},
-	[DA9052_IRQ_GPI10] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_3,
-	},
-	[DA9052_IRQ_GPI11] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_4,
-	},
-	[DA9052_IRQ_GPI12] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_5,
-	},
-	[DA9052_IRQ_GPI13] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_6,
-	},
-	[DA9052_IRQ_GPI14] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_7,
-	},
-	[DA9052_IRQ_GPI15] = {
-		.reg_offset = 3,
-		.mask = DA9052_IRQ_MASK_POS_8,
-	},
-};
-
-static struct regmap_irq_chip da9052_regmap_irq_chip = {
-	.name = "da9052_irq",
-	.status_base = DA9052_EVENT_A_REG,
-	.mask_base = DA9052_IRQ_MASK_A_REG,
-	.ack_base = DA9052_EVENT_A_REG,
-	.num_regs = DA9052_NUM_IRQ_REGS,
-	.irqs = da9052_irqs,
-	.num_irqs = ARRAY_SIZE(da9052_irqs),
-};
-
 struct regmap_config da9052_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -782,45 +545,31 @@
 
 	da9052->chip_id = chip_id;
 
-	if (!pdata || !pdata->irq_base)
-		da9052->irq_base = -1;
-	else
-		da9052->irq_base = pdata->irq_base;
-
-	ret = regmap_add_irq_chip(da9052->regmap, da9052->chip_irq,
-				  IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				  da9052->irq_base, &da9052_regmap_irq_chip,
-				  &da9052->irq_data);
-	if (ret < 0)
-		goto regmap_err;
-
-	da9052->irq_base = regmap_irq_chip_get_base(da9052->irq_data);
-
-	ret = request_threaded_irq(DA9052_IRQ_ADC_EOM, NULL, da9052_auxadc_irq,
-				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-				   "adc irq", da9052);
-	if (ret != 0)
-		dev_err(da9052->dev, "DA9052 ADC IRQ failed ret=%d\n", ret);
+	ret = da9052_irq_init(da9052);
+	if (ret != 0) {
+		dev_err(da9052->dev, "da9052_irq_init failed: %d\n", ret);
+		return ret;
+	}
 
 	ret = mfd_add_devices(da9052->dev, -1, da9052_subdev_info,
 			      ARRAY_SIZE(da9052_subdev_info), NULL, 0, NULL);
-	if (ret)
+	if (ret) {
+		dev_err(da9052->dev, "mfd_add_devices failed: %d\n", ret);
 		goto err;
+	}
 
 	return 0;
 
 err:
-	free_irq(DA9052_IRQ_ADC_EOM, da9052);
-	mfd_remove_devices(da9052->dev);
-regmap_err:
+	da9052_irq_exit(da9052);
+
 	return ret;
 }
 
 void da9052_device_exit(struct da9052 *da9052)
 {
-	free_irq(DA9052_IRQ_ADC_EOM, da9052);
-	regmap_del_irq_chip(da9052->chip_irq, da9052->irq_data);
 	mfd_remove_devices(da9052->dev);
+	da9052_irq_exit(da9052);
 }
 
 MODULE_AUTHOR("David Dajun Chen <dchen@diasemi.com>");
diff --git a/drivers/mfd/da9052-irq.c b/drivers/mfd/da9052-irq.c
new file mode 100644
index 0000000..57ae784
--- /dev/null
+++ b/drivers/mfd/da9052-irq.c
@@ -0,0 +1,288 @@
+/*
+ * DA9052 interrupt support
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ * Based on arizona-irq.c, which is:
+ *
+ * Copyright 2012 Wolfson Microelectronics plc
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+
+#include <linux/mfd/da9052/da9052.h>
+#include <linux/mfd/da9052/reg.h>
+
+#define DA9052_NUM_IRQ_REGS		4
+#define DA9052_IRQ_MASK_POS_1		0x01
+#define DA9052_IRQ_MASK_POS_2		0x02
+#define DA9052_IRQ_MASK_POS_3		0x04
+#define DA9052_IRQ_MASK_POS_4		0x08
+#define DA9052_IRQ_MASK_POS_5		0x10
+#define DA9052_IRQ_MASK_POS_6		0x20
+#define DA9052_IRQ_MASK_POS_7		0x40
+#define DA9052_IRQ_MASK_POS_8		0x80
+
+static struct regmap_irq da9052_irqs[] = {
+	[DA9052_IRQ_DCIN] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_1,
+	},
+	[DA9052_IRQ_VBUS] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_2,
+	},
+	[DA9052_IRQ_DCINREM] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_3,
+	},
+	[DA9052_IRQ_VBUSREM] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_4,
+	},
+	[DA9052_IRQ_VDDLOW] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_5,
+	},
+	[DA9052_IRQ_ALARM] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_6,
+	},
+	[DA9052_IRQ_SEQRDY] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_7,
+	},
+	[DA9052_IRQ_COMP1V2] = {
+		.reg_offset = 0,
+		.mask = DA9052_IRQ_MASK_POS_8,
+	},
+	[DA9052_IRQ_NONKEY] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_1,
+	},
+	[DA9052_IRQ_IDFLOAT] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_2,
+	},
+	[DA9052_IRQ_IDGND] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_3,
+	},
+	[DA9052_IRQ_CHGEND] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_4,
+	},
+	[DA9052_IRQ_TBAT] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_5,
+	},
+	[DA9052_IRQ_ADC_EOM] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_6,
+	},
+	[DA9052_IRQ_PENDOWN] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_7,
+	},
+	[DA9052_IRQ_TSIREADY] = {
+		.reg_offset = 1,
+		.mask = DA9052_IRQ_MASK_POS_8,
+	},
+	[DA9052_IRQ_GPI0] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_1,
+	},
+	[DA9052_IRQ_GPI1] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_2,
+	},
+	[DA9052_IRQ_GPI2] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_3,
+	},
+	[DA9052_IRQ_GPI3] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_4,
+	},
+	[DA9052_IRQ_GPI4] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_5,
+	},
+	[DA9052_IRQ_GPI5] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_6,
+	},
+	[DA9052_IRQ_GPI6] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_7,
+	},
+	[DA9052_IRQ_GPI7] = {
+		.reg_offset = 2,
+		.mask = DA9052_IRQ_MASK_POS_8,
+	},
+	[DA9052_IRQ_GPI8] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_1,
+	},
+	[DA9052_IRQ_GPI9] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_2,
+	},
+	[DA9052_IRQ_GPI10] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_3,
+	},
+	[DA9052_IRQ_GPI11] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_4,
+	},
+	[DA9052_IRQ_GPI12] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_5,
+	},
+	[DA9052_IRQ_GPI13] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_6,
+	},
+	[DA9052_IRQ_GPI14] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_7,
+	},
+	[DA9052_IRQ_GPI15] = {
+		.reg_offset = 3,
+		.mask = DA9052_IRQ_MASK_POS_8,
+	},
+};
+
+static struct regmap_irq_chip da9052_regmap_irq_chip = {
+	.name = "da9052_irq",
+	.status_base = DA9052_EVENT_A_REG,
+	.mask_base = DA9052_IRQ_MASK_A_REG,
+	.ack_base = DA9052_EVENT_A_REG,
+	.num_regs = DA9052_NUM_IRQ_REGS,
+	.irqs = da9052_irqs,
+	.num_irqs = ARRAY_SIZE(da9052_irqs),
+};
+
+static int da9052_map_irq(struct da9052 *da9052, int irq)
+{
+	return regmap_irq_get_virq(da9052->irq_data, irq);
+}
+
+int da9052_enable_irq(struct da9052 *da9052, int irq)
+{
+	irq = da9052_map_irq(da9052, irq);
+	if (irq < 0)
+		return irq;
+
+	enable_irq(irq);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(da9052_enable_irq);
+
+int da9052_disable_irq(struct da9052 *da9052, int irq)
+{
+	irq = da9052_map_irq(da9052, irq);
+	if (irq < 0)
+		return irq;
+
+	disable_irq(irq);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(da9052_disable_irq);
+
+int da9052_disable_irq_nosync(struct da9052 *da9052, int irq)
+{
+	irq = da9052_map_irq(da9052, irq);
+	if (irq < 0)
+		return irq;
+
+	disable_irq_nosync(irq);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(da9052_disable_irq_nosync);
+
+int da9052_request_irq(struct da9052 *da9052, int irq, char *name,
+			   irq_handler_t handler, void *data)
+{
+	irq = da9052_map_irq(da9052, irq);
+	if (irq < 0)
+		return irq;
+
+	return request_threaded_irq(irq, NULL, handler,
+				     IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				     name, data);
+}
+EXPORT_SYMBOL_GPL(da9052_request_irq);
+
+void da9052_free_irq(struct da9052 *da9052, int irq, void *data)
+{
+	irq = da9052_map_irq(da9052, irq);
+	if (irq < 0)
+		return;
+
+	free_irq(irq, data);
+}
+EXPORT_SYMBOL_GPL(da9052_free_irq);
+
+static irqreturn_t da9052_auxadc_irq(int irq, void *irq_data)
+{
+	struct da9052 *da9052 = irq_data;
+
+	complete(&da9052->done);
+
+	return IRQ_HANDLED;
+}
+
+int da9052_irq_init(struct da9052 *da9052)
+{
+	int ret;
+
+	ret = regmap_add_irq_chip(da9052->regmap, da9052->chip_irq,
+				  IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				  -1, &da9052_regmap_irq_chip,
+				  &da9052->irq_data);
+	if (ret < 0) {
+		dev_err(da9052->dev, "regmap_add_irq_chip failed: %d\n", ret);
+		goto regmap_err;
+	}
+
+	ret = da9052_request_irq(da9052, DA9052_IRQ_ADC_EOM, "adc-irq",
+			    da9052_auxadc_irq, da9052);
+
+	if (ret != 0) {
+		dev_err(da9052->dev, "DA9052_IRQ_ADC_EOM failed: %d\n", ret);
+		goto request_irq_err;
+	}
+
+	return 0;
+
+request_irq_err:
+	regmap_del_irq_chip(da9052->chip_irq, da9052->irq_data);
+regmap_err:
+	return ret;
+
+}
+
+int da9052_irq_exit(struct da9052 *da9052)
+{
+	da9052_free_irq(da9052, DA9052_IRQ_ADC_EOM , da9052);
+	regmap_del_irq_chip(da9052->chip_irq, da9052->irq_data);
+
+	return 0;
+}
diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 2971056..dc8826d 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -2763,7 +2763,7 @@
 
 void __init db8500_prcmu_early_init(void)
 {
-	if (cpu_is_u8500v2()) {
+	if (cpu_is_u8500v2() || cpu_is_u9540()) {
 		void *tcpm_base = ioremap_nocache(U8500_PRCMU_TCPM_BASE, SZ_4K);
 
 		if (tcpm_base != NULL) {
@@ -2781,7 +2781,11 @@
 			iounmap(tcpm_base);
 		}
 
-		tcdm_base = __io_address(U8500_PRCMU_TCDM_BASE);
+		if (cpu_is_u9540())
+			tcdm_base = ioremap_nocache(U8500_PRCMU_TCDM_BASE,
+						SZ_4K + SZ_8K) + SZ_8K;
+		else
+			tcdm_base = __io_address(U8500_PRCMU_TCDM_BASE);
 	} else {
 		pr_err("prcmu: Unsupported chip version\n");
 		BUG();
diff --git a/drivers/mfd/jz4740-adc.c b/drivers/mfd/jz4740-adc.c
index 0b8b55b..e80587f 100644
--- a/drivers/mfd/jz4740-adc.c
+++ b/drivers/mfd/jz4740-adc.c
@@ -211,7 +211,7 @@
 	int ret;
 	int irq_base;
 
-	adc = kmalloc(sizeof(*adc), GFP_KERNEL);
+	adc = devm_kzalloc(&pdev->dev, sizeof(*adc), GFP_KERNEL);
 	if (!adc) {
 		dev_err(&pdev->dev, "Failed to allocate driver structure\n");
 		return -ENOMEM;
@@ -221,30 +221,27 @@
 	if (adc->irq < 0) {
 		ret = adc->irq;
 		dev_err(&pdev->dev, "Failed to get platform irq: %d\n", ret);
-		goto err_free;
+		return ret;
 	}
 
 	irq_base = platform_get_irq(pdev, 1);
 	if (irq_base < 0) {
-		ret = irq_base;
-		dev_err(&pdev->dev, "Failed to get irq base: %d\n", ret);
-		goto err_free;
+		dev_err(&pdev->dev, "Failed to get irq base: %d\n", irq_base);
+		return irq_base;
 	}
 
 	mem_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!mem_base) {
-		ret = -ENOENT;
 		dev_err(&pdev->dev, "Failed to get platform mmio resource\n");
-		goto err_free;
+		return -ENOENT;
 	}
 
 	/* Only request the shared registers for the MFD driver */
 	adc->mem = request_mem_region(mem_base->start, JZ_REG_ADC_STATUS,
 					pdev->name);
 	if (!adc->mem) {
-		ret = -EBUSY;
 		dev_err(&pdev->dev, "Failed to request mmio memory region\n");
-		goto err_free;
+		return -EBUSY;
 	}
 
 	adc->base = ioremap_nocache(adc->mem->start, resource_size(adc->mem));
@@ -301,9 +298,6 @@
 	iounmap(adc->base);
 err_release_mem_region:
 	release_mem_region(adc->mem->start, resource_size(adc->mem));
-err_free:
-	kfree(adc);
-
 	return ret;
 }
 
@@ -325,8 +319,6 @@
 
 	platform_set_drvdata(pdev, NULL);
 
-	kfree(adc);
-
 	return 0;
 }
 
diff --git a/drivers/mfd/lpc_ich.c b/drivers/mfd/lpc_ich.c
index 2ad24ca..d9d9303 100644
--- a/drivers/mfd/lpc_ich.c
+++ b/drivers/mfd/lpc_ich.c
@@ -734,7 +734,7 @@
 	pci_read_config_dword(dev, ACPIBASE, &base_addr_cfg);
 	base_addr = base_addr_cfg & 0x0000ff80;
 	if (!base_addr) {
-		dev_err(&dev->dev, "I/O space for ACPI uninitialized\n");
+		dev_notice(&dev->dev, "I/O space for ACPI uninitialized\n");
 		lpc_ich_cells[LPC_GPIO].num_resources--;
 		goto gpe0_done;
 	}
@@ -760,7 +760,7 @@
 	pci_read_config_dword(dev, GPIOBASE, &base_addr_cfg);
 	base_addr = base_addr_cfg & 0x0000ff80;
 	if (!base_addr) {
-		dev_err(&dev->dev, "I/O space for GPIO uninitialized\n");
+		dev_notice(&dev->dev, "I/O space for GPIO uninitialized\n");
 		ret = -ENODEV;
 		goto gpio_done;
 	}
@@ -810,7 +810,7 @@
 	pci_read_config_dword(dev, ACPIBASE, &base_addr_cfg);
 	base_addr = base_addr_cfg & 0x0000ff80;
 	if (!base_addr) {
-		dev_err(&dev->dev, "I/O space for ACPI uninitialized\n");
+		dev_notice(&dev->dev, "I/O space for ACPI uninitialized\n");
 		ret = -ENODEV;
 		goto wdt_done;
 	}
@@ -830,12 +830,15 @@
 	 * we have to read RCBA from PCI Config space 0xf0 and use
 	 * it as base. GCS = RCBA + ICH6_GCS(0x3410).
 	 */
-	if (lpc_chipset_info[id->driver_data].iTCO_version == 2) {
+	if (lpc_chipset_info[id->driver_data].iTCO_version == 1) {
+		/* Don't register iomem for TCO ver 1 */
+		lpc_ich_cells[LPC_WDT].num_resources--;
+	} else {
 		pci_read_config_dword(dev, RCBABASE, &base_addr_cfg);
 		base_addr = base_addr_cfg & 0xffffc000;
 		if (!(base_addr_cfg & 1)) {
-			pr_err("RCBA is disabled by hardware/BIOS, "
-					"device disabled\n");
+			dev_notice(&dev->dev, "RCBA is disabled by "
+					"hardware/BIOS, device disabled\n");
 			ret = -ENODEV;
 			goto wdt_done;
 		}
@@ -871,6 +874,7 @@
 	 * successfully.
 	 */
 	if (!cell_added) {
+		dev_warn(&dev->dev, "No MFD cells added\n");
 		lpc_ich_restore_config_space(dev);
 		return -ENODEV;
 	}
diff --git a/drivers/mfd/mc13xxx-core.c b/drivers/mfd/mc13xxx-core.c
index 1aba023..2a9b100 100644
--- a/drivers/mfd/mc13xxx-core.c
+++ b/drivers/mfd/mc13xxx-core.c
@@ -119,6 +119,11 @@
 #define MC13XXX_REVISION_FAB		(0x03 << 11)
 #define MC13XXX_REVISION_ICIDCODE	(0x3f << 13)
 
+#define MC34708_REVISION_REVMETAL	(0x07 <<  0)
+#define MC34708_REVISION_REVFULL	(0x07 <<  3)
+#define MC34708_REVISION_FIN		(0x07 <<  6)
+#define MC34708_REVISION_FAB		(0x07 <<  9)
+
 #define MC13XXX_ADC1		44
 #define MC13XXX_ADC1_ADEN		(1 << 0)
 #define MC13XXX_ADC1_RAND		(1 << 1)
@@ -410,62 +415,52 @@
 	return IRQ_RETVAL(handled);
 }
 
-static const char *mc13xxx_chipname[] = {
-	[MC13XXX_ID_MC13783] = "mc13783",
-	[MC13XXX_ID_MC13892] = "mc13892",
-};
-
 #define maskval(reg, mask)	(((reg) & (mask)) >> __ffs(mask))
-static int mc13xxx_identify(struct mc13xxx *mc13xxx)
+static void mc13xxx_print_revision(struct mc13xxx *mc13xxx, u32 revision)
 {
-	u32 icid;
-	u32 revision;
-	int ret;
-
-	/*
-	 * Get the generation ID from register 46, as apparently some older
-	 * IC revisions only have this info at this location. Newer ICs seem to
-	 * have both.
-	 */
-	ret = mc13xxx_reg_read(mc13xxx, 46, &icid);
-	if (ret)
-		return ret;
-
-	icid = (icid >> 6) & 0x7;
-
-	switch (icid) {
-	case 2:
-		mc13xxx->ictype = MC13XXX_ID_MC13783;
-		break;
-	case 7:
-		mc13xxx->ictype = MC13XXX_ID_MC13892;
-		break;
-	default:
-		mc13xxx->ictype = MC13XXX_ID_INVALID;
-		break;
-	}
-
-	if (mc13xxx->ictype == MC13XXX_ID_MC13783 ||
-			mc13xxx->ictype == MC13XXX_ID_MC13892) {
-		ret = mc13xxx_reg_read(mc13xxx, MC13XXX_REVISION, &revision);
-
-		dev_info(mc13xxx->dev, "%s: rev: %d.%d, "
-				"fin: %d, fab: %d, icid: %d/%d\n",
-				mc13xxx_chipname[mc13xxx->ictype],
-				maskval(revision, MC13XXX_REVISION_REVFULL),
-				maskval(revision, MC13XXX_REVISION_REVMETAL),
-				maskval(revision, MC13XXX_REVISION_FIN),
-				maskval(revision, MC13XXX_REVISION_FAB),
-				maskval(revision, MC13XXX_REVISION_ICID),
-				maskval(revision, MC13XXX_REVISION_ICIDCODE));
-	}
-
-	return (mc13xxx->ictype == MC13XXX_ID_INVALID) ? -ENODEV : 0;
+	dev_info(mc13xxx->dev, "%s: rev: %d.%d, "
+			"fin: %d, fab: %d, icid: %d/%d\n",
+			mc13xxx->variant->name,
+			maskval(revision, MC13XXX_REVISION_REVFULL),
+			maskval(revision, MC13XXX_REVISION_REVMETAL),
+			maskval(revision, MC13XXX_REVISION_FIN),
+			maskval(revision, MC13XXX_REVISION_FAB),
+			maskval(revision, MC13XXX_REVISION_ICID),
+			maskval(revision, MC13XXX_REVISION_ICIDCODE));
 }
 
+static void mc34708_print_revision(struct mc13xxx *mc13xxx, u32 revision)
+{
+	dev_info(mc13xxx->dev, "%s: rev %d.%d, fin: %d, fab: %d\n",
+			mc13xxx->variant->name,
+			maskval(revision, MC34708_REVISION_REVFULL),
+			maskval(revision, MC34708_REVISION_REVMETAL),
+			maskval(revision, MC34708_REVISION_FIN),
+			maskval(revision, MC34708_REVISION_FAB));
+}
+
+/* These are only exported for mc13xxx-i2c and mc13xxx-spi */
+struct mc13xxx_variant mc13xxx_variant_mc13783 = {
+	.name = "mc13783",
+	.print_revision = mc13xxx_print_revision,
+};
+EXPORT_SYMBOL_GPL(mc13xxx_variant_mc13783);
+
+struct mc13xxx_variant mc13xxx_variant_mc13892 = {
+	.name = "mc13892",
+	.print_revision = mc13xxx_print_revision,
+};
+EXPORT_SYMBOL_GPL(mc13xxx_variant_mc13892);
+
+struct mc13xxx_variant mc13xxx_variant_mc34708 = {
+	.name = "mc34708",
+	.print_revision = mc34708_print_revision,
+};
+EXPORT_SYMBOL_GPL(mc13xxx_variant_mc34708);
+
 static const char *mc13xxx_get_chipname(struct mc13xxx *mc13xxx)
 {
-	return mc13xxx_chipname[mc13xxx->ictype];
+	return mc13xxx->variant->name;
 }
 
 int mc13xxx_get_flags(struct mc13xxx *mc13xxx)
@@ -653,13 +648,16 @@
 		struct mc13xxx_platform_data *pdata, int irq)
 {
 	int ret;
+	u32 revision;
 
 	mc13xxx_lock(mc13xxx);
 
-	ret = mc13xxx_identify(mc13xxx);
+	ret = mc13xxx_reg_read(mc13xxx, MC13XXX_REVISION, &revision);
 	if (ret)
 		goto err_revision;
 
+	mc13xxx->variant->print_revision(mc13xxx, revision);
+
 	/* mask all irqs */
 	ret = mc13xxx_reg_write(mc13xxx, MC13XXX_IRQMASK0, 0x00ffffff);
 	if (ret)
diff --git a/drivers/mfd/mc13xxx-i2c.c b/drivers/mfd/mc13xxx-i2c.c
index 7957999..f745e27 100644
--- a/drivers/mfd/mc13xxx-i2c.c
+++ b/drivers/mfd/mc13xxx-i2c.c
@@ -24,7 +24,10 @@
 static const struct i2c_device_id mc13xxx_i2c_device_id[] = {
 	{
 		.name = "mc13892",
-		.driver_data = MC13XXX_ID_MC13892,
+		.driver_data = (kernel_ulong_t)&mc13xxx_variant_mc13892,
+	}, {
+		.name = "mc34708",
+		.driver_data = (kernel_ulong_t)&mc13xxx_variant_mc34708,
 	}, {
 		/* sentinel */
 	}
@@ -34,7 +37,10 @@
 static const struct of_device_id mc13xxx_dt_ids[] = {
 	{
 		.compatible = "fsl,mc13892",
-		.data = (void *) &mc13xxx_i2c_device_id[0],
+		.data = &mc13xxx_variant_mc13892,
+	}, {
+		.compatible = "fsl,mc34708",
+		.data = &mc13xxx_variant_mc34708,
 	}, {
 		/* sentinel */
 	}
@@ -76,11 +82,15 @@
 		return ret;
 	}
 
-	ret = mc13xxx_common_init(mc13xxx, pdata, client->irq);
+	if (client->dev.of_node) {
+		const struct of_device_id *of_id =
+			of_match_device(mc13xxx_dt_ids, &client->dev);
+		mc13xxx->variant = of_id->data;
+	} else {
+		mc13xxx->variant = (void *)id->driver_data;
+	}
 
-	if (ret == 0 && (id->driver_data != mc13xxx->ictype))
-		dev_warn(mc13xxx->dev,
-				"device id doesn't match auto detection!\n");
+	ret = mc13xxx_common_init(mc13xxx, pdata, client->irq);
 
 	return ret;
 }
diff --git a/drivers/mfd/mc13xxx-spi.c b/drivers/mfd/mc13xxx-spi.c
index cb32f69..3032bae 100644
--- a/drivers/mfd/mc13xxx-spi.c
+++ b/drivers/mfd/mc13xxx-spi.c
@@ -28,10 +28,13 @@
 static const struct spi_device_id mc13xxx_device_id[] = {
 	{
 		.name = "mc13783",
-		.driver_data = MC13XXX_ID_MC13783,
+		.driver_data = (kernel_ulong_t)&mc13xxx_variant_mc13783,
 	}, {
 		.name = "mc13892",
-		.driver_data = MC13XXX_ID_MC13892,
+		.driver_data = (kernel_ulong_t)&mc13xxx_variant_mc13892,
+	}, {
+		.name = "mc34708",
+		.driver_data = (kernel_ulong_t)&mc13xxx_variant_mc34708,
 	}, {
 		/* sentinel */
 	}
@@ -39,8 +42,9 @@
 MODULE_DEVICE_TABLE(spi, mc13xxx_device_id);
 
 static const struct of_device_id mc13xxx_dt_ids[] = {
-	{ .compatible = "fsl,mc13783", .data = (void *) MC13XXX_ID_MC13783, },
-	{ .compatible = "fsl,mc13892", .data = (void *) MC13XXX_ID_MC13892, },
+	{ .compatible = "fsl,mc13783", .data = &mc13xxx_variant_mc13783, },
+	{ .compatible = "fsl,mc13892", .data = &mc13xxx_variant_mc13892, },
+	{ .compatible = "fsl,mc34708", .data = &mc13xxx_variant_mc34708, },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, mc13xxx_dt_ids);
@@ -144,19 +148,18 @@
 		return ret;
 	}
 
-	ret = mc13xxx_common_init(mc13xxx, pdata, spi->irq);
+	if (spi->dev.of_node) {
+		const struct of_device_id *of_id =
+			of_match_device(mc13xxx_dt_ids, &spi->dev);
 
-	if (ret) {
-		dev_set_drvdata(&spi->dev, NULL);
+		mc13xxx->variant = of_id->data;
 	} else {
-		const struct spi_device_id *devid =
-			spi_get_device_id(spi);
-		if (!devid || devid->driver_data != mc13xxx->ictype)
-			dev_warn(mc13xxx->dev,
-				"device id doesn't match auto detection!\n");
+		const struct spi_device_id *id_entry = spi_get_device_id(spi);
+
+		mc13xxx->variant = (void *)id_entry->driver_data;
 	}
 
-	return ret;
+	return mc13xxx_common_init(mc13xxx, pdata, spi->irq);
 }
 
 static int mc13xxx_spi_remove(struct spi_device *spi)
diff --git a/drivers/mfd/mc13xxx.h b/drivers/mfd/mc13xxx.h
index bbba06f..460ec5c 100644
--- a/drivers/mfd/mc13xxx.h
+++ b/drivers/mfd/mc13xxx.h
@@ -13,19 +13,25 @@
 #include <linux/regmap.h>
 #include <linux/mfd/mc13xxx.h>
 
-enum mc13xxx_id {
-	MC13XXX_ID_MC13783,
-	MC13XXX_ID_MC13892,
-	MC13XXX_ID_INVALID,
+#define MC13XXX_NUMREGS 0x3f
+
+struct mc13xxx;
+
+struct mc13xxx_variant {
+	const char *name;
+	void (*print_revision)(struct mc13xxx *mc13xxx, u32 revision);
 };
 
-#define MC13XXX_NUMREGS 0x3f
+extern struct mc13xxx_variant
+		mc13xxx_variant_mc13783,
+		mc13xxx_variant_mc13892,
+		mc13xxx_variant_mc34708;
 
 struct mc13xxx {
 	struct regmap *regmap;
 
 	struct device *dev;
-	enum mc13xxx_id ictype;
+	const struct mc13xxx_variant *variant;
 
 	struct mutex lock;
 	int irq;
diff --git a/drivers/mfd/mfd-core.c b/drivers/mfd/mfd-core.c
index f8b7771..7604f4e 100644
--- a/drivers/mfd/mfd-core.c
+++ b/drivers/mfd/mfd-core.c
@@ -21,6 +21,10 @@
 #include <linux/irqdomain.h>
 #include <linux/of.h>
 
+static struct device_type mfd_dev_type = {
+	.name	= "mfd_device",
+};
+
 int mfd_cell_enable(struct platform_device *pdev)
 {
 	const struct mfd_cell *cell = mfd_get_cell(pdev);
@@ -91,6 +95,7 @@
 		goto fail_device;
 
 	pdev->dev.parent = parent;
+	pdev->dev.type = &mfd_dev_type;
 
 	if (parent->of_node && cell->of_compatible) {
 		for_each_child_of_node(parent->of_node, np) {
@@ -204,10 +209,16 @@
 
 static int mfd_remove_devices_fn(struct device *dev, void *c)
 {
-	struct platform_device *pdev = to_platform_device(dev);
-	const struct mfd_cell *cell = mfd_get_cell(pdev);
+	struct platform_device *pdev;
+	const struct mfd_cell *cell;
 	atomic_t **usage_count = c;
 
+	if (dev->type != &mfd_dev_type)
+		return 0;
+
+	pdev = to_platform_device(dev);
+	cell = mfd_get_cell(pdev);
+
 	/* find the base address of usage_count pointers (for freeing) */
 	if (!*usage_count || (cell->usage_count < *usage_count))
 		*usage_count = cell->usage_count;
diff --git a/drivers/mfd/rc5t583-irq.c b/drivers/mfd/rc5t583-irq.c
index fe00cdd..b41db59 100644
--- a/drivers/mfd/rc5t583-irq.c
+++ b/drivers/mfd/rc5t583-irq.c
@@ -345,7 +345,7 @@
 	mutex_init(&rc5t583->irq_lock);
 
 	/* Initailize all int register to 0 */
-	for (i = 0; i < RC5T583_MAX_INTERRUPT_MASK_REGS; i++)  {
+	for (i = 0; i < RC5T583_MAX_INTERRUPT_EN_REGS; i++)  {
 		ret = rc5t583_write(rc5t583->dev, irq_en_add[i],
 				rc5t583->irq_en_reg[i]);
 		if (ret < 0)
diff --git a/drivers/mfd/retu-mfd.c b/drivers/mfd/retu-mfd.c
new file mode 100644
index 0000000..7ff4a37
--- /dev/null
+++ b/drivers/mfd/retu-mfd.c
@@ -0,0 +1,264 @@
+/*
+ * Retu MFD driver
+ *
+ * Copyright (C) 2004, 2005 Nokia Corporation
+ *
+ * Based on code written by Juha Yrjölä, David Weinehall and Mikko Ylinen.
+ * Rewritten by Aaro Koskinen.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/irq.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/mutex.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/retu.h>
+#include <linux/interrupt.h>
+#include <linux/moduleparam.h>
+
+/* Registers */
+#define RETU_REG_ASICR		0x00		/* ASIC ID and revision */
+#define RETU_REG_ASICR_VILMA	(1 << 7)	/* Bit indicating Vilma */
+#define RETU_REG_IDR		0x01		/* Interrupt ID */
+#define RETU_REG_IMR		0x02		/* Interrupt mask */
+
+/* Interrupt sources */
+#define RETU_INT_PWR		0		/* Power button */
+
+struct retu_dev {
+	struct regmap			*regmap;
+	struct device			*dev;
+	struct mutex			mutex;
+	struct regmap_irq_chip_data	*irq_data;
+};
+
+static struct resource retu_pwrbutton_res[] = {
+	{
+		.name	= "retu-pwrbutton",
+		.start	= RETU_INT_PWR,
+		.end	= RETU_INT_PWR,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct mfd_cell retu_devs[] = {
+	{
+		.name		= "retu-wdt"
+	},
+	{
+		.name		= "retu-pwrbutton",
+		.resources	= retu_pwrbutton_res,
+		.num_resources	= ARRAY_SIZE(retu_pwrbutton_res),
+	}
+};
+
+static struct regmap_irq retu_irqs[] = {
+	[RETU_INT_PWR] = {
+		.mask = 1 << RETU_INT_PWR,
+	}
+};
+
+static struct regmap_irq_chip retu_irq_chip = {
+	.name		= "RETU",
+	.irqs		= retu_irqs,
+	.num_irqs	= ARRAY_SIZE(retu_irqs),
+	.num_regs	= 1,
+	.status_base	= RETU_REG_IDR,
+	.mask_base	= RETU_REG_IMR,
+	.ack_base	= RETU_REG_IDR,
+};
+
+/* Retu device registered for the power off. */
+static struct retu_dev *retu_pm_power_off;
+
+int retu_read(struct retu_dev *rdev, u8 reg)
+{
+	int ret;
+	int value;
+
+	mutex_lock(&rdev->mutex);
+	ret = regmap_read(rdev->regmap, reg, &value);
+	mutex_unlock(&rdev->mutex);
+
+	return ret ? ret : value;
+}
+EXPORT_SYMBOL_GPL(retu_read);
+
+int retu_write(struct retu_dev *rdev, u8 reg, u16 data)
+{
+	int ret;
+
+	mutex_lock(&rdev->mutex);
+	ret = regmap_write(rdev->regmap, reg, data);
+	mutex_unlock(&rdev->mutex);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(retu_write);
+
+static void retu_power_off(void)
+{
+	struct retu_dev *rdev = retu_pm_power_off;
+	int reg;
+
+	mutex_lock(&retu_pm_power_off->mutex);
+
+	/* Ignore power button state */
+	regmap_read(rdev->regmap, RETU_REG_CC1, &reg);
+	regmap_write(rdev->regmap, RETU_REG_CC1, reg | 2);
+
+	/* Expire watchdog immediately */
+	regmap_write(rdev->regmap, RETU_REG_WATCHDOG, 0);
+
+	/* Wait for poweroff */
+	for (;;)
+		cpu_relax();
+
+	mutex_unlock(&retu_pm_power_off->mutex);
+}
+
+static int retu_regmap_read(void *context, const void *reg, size_t reg_size,
+			    void *val, size_t val_size)
+{
+	int ret;
+	struct device *dev = context;
+	struct i2c_client *i2c = to_i2c_client(dev);
+
+	BUG_ON(reg_size != 1 || val_size != 2);
+
+	ret = i2c_smbus_read_word_data(i2c, *(u8 const *)reg);
+	if (ret < 0)
+		return ret;
+
+	*(u16 *)val = ret;
+	return 0;
+}
+
+static int retu_regmap_write(void *context, const void *data, size_t count)
+{
+	u8 reg;
+	u16 val;
+	struct device *dev = context;
+	struct i2c_client *i2c = to_i2c_client(dev);
+
+	BUG_ON(count != sizeof(reg) + sizeof(val));
+	memcpy(&reg, data, sizeof(reg));
+	memcpy(&val, data + sizeof(reg), sizeof(val));
+	return i2c_smbus_write_word_data(i2c, reg, val);
+}
+
+static struct regmap_bus retu_bus = {
+	.read = retu_regmap_read,
+	.write = retu_regmap_write,
+	.val_format_endian_default = REGMAP_ENDIAN_NATIVE,
+};
+
+static struct regmap_config retu_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+};
+
+static int __devinit retu_probe(struct i2c_client *i2c,
+				const struct i2c_device_id *id)
+{
+	struct retu_dev *rdev;
+	int ret;
+
+	rdev = devm_kzalloc(&i2c->dev, sizeof(*rdev), GFP_KERNEL);
+	if (rdev == NULL)
+		return -ENOMEM;
+
+	i2c_set_clientdata(i2c, rdev);
+	rdev->dev = &i2c->dev;
+	mutex_init(&rdev->mutex);
+	rdev->regmap = devm_regmap_init(&i2c->dev, &retu_bus, &i2c->dev,
+					&retu_config);
+	if (IS_ERR(rdev->regmap))
+		return PTR_ERR(rdev->regmap);
+
+	ret = retu_read(rdev, RETU_REG_ASICR);
+	if (ret < 0) {
+		dev_err(rdev->dev, "could not read Retu revision: %d\n", ret);
+		return ret;
+	}
+
+	dev_info(rdev->dev, "Retu%s v%d.%d found\n",
+		 (ret & RETU_REG_ASICR_VILMA) ? " & Vilma" : "",
+		 (ret >> 4) & 0x7, ret & 0xf);
+
+	/* Mask all RETU interrupts. */
+	ret = retu_write(rdev, RETU_REG_IMR, 0xffff);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_add_irq_chip(rdev->regmap, i2c->irq, IRQF_ONESHOT, -1,
+				  &retu_irq_chip, &rdev->irq_data);
+	if (ret < 0)
+		return ret;
+
+	ret = mfd_add_devices(rdev->dev, -1, retu_devs, ARRAY_SIZE(retu_devs),
+			      NULL, regmap_irq_chip_get_base(rdev->irq_data),
+			      NULL);
+	if (ret < 0) {
+		regmap_del_irq_chip(i2c->irq, rdev->irq_data);
+		return ret;
+	}
+
+	if (!pm_power_off) {
+		retu_pm_power_off = rdev;
+		pm_power_off	  = retu_power_off;
+	}
+
+	return 0;
+}
+
+static int __devexit retu_remove(struct i2c_client *i2c)
+{
+	struct retu_dev *rdev = i2c_get_clientdata(i2c);
+
+	if (retu_pm_power_off == rdev) {
+		pm_power_off	  = NULL;
+		retu_pm_power_off = NULL;
+	}
+	mfd_remove_devices(rdev->dev);
+	regmap_del_irq_chip(i2c->irq, rdev->irq_data);
+
+	return 0;
+}
+
+static const struct i2c_device_id retu_id[] = {
+	{ "retu-mfd", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, retu_id);
+
+static struct i2c_driver retu_driver = {
+	.driver		= {
+		.name = "retu-mfd",
+		.owner = THIS_MODULE,
+	},
+	.probe		= retu_probe,
+	.remove		= retu_remove,
+	.id_table	= retu_id,
+};
+module_i2c_driver(retu_driver);
+
+MODULE_DESCRIPTION("Retu MFD driver");
+MODULE_AUTHOR("Juha Yrjölä");
+MODULE_AUTHOR("David Weinehall");
+MODULE_AUTHOR("Mikko Ylinen");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/rtsx_pcr.c b/drivers/mfd/rtsx_pcr.c
index 56d4377..3a44efa 100644
--- a/drivers/mfd/rtsx_pcr.c
+++ b/drivers/mfd/rtsx_pcr.c
@@ -22,6 +22,7 @@
 
 #include <linux/pci.h>
 #include <linux/module.h>
+#include <linux/slab.h>
 #include <linux/dma-mapping.h>
 #include <linux/highmem.h>
 #include <linux/interrupt.h>
diff --git a/drivers/mfd/sec-irq.c b/drivers/mfd/sec-irq.c
index c901fa5..0dd84e9 100644
--- a/drivers/mfd/sec-irq.c
+++ b/drivers/mfd/sec-irq.c
@@ -24,67 +24,67 @@
 
 static struct regmap_irq s2mps11_irqs[] = {
 	[S2MPS11_IRQ_PWRONF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_PWRONF_MASK,
 	},
 	[S2MPS11_IRQ_PWRONR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_PWRONR_MASK,
 	},
 	[S2MPS11_IRQ_JIGONBF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_JIGONBF_MASK,
 	},
 	[S2MPS11_IRQ_JIGONBR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_JIGONBR_MASK,
 	},
 	[S2MPS11_IRQ_ACOKBF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_ACOKBF_MASK,
 	},
 	[S2MPS11_IRQ_ACOKBR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_ACOKBR_MASK,
 	},
 	[S2MPS11_IRQ_PWRON1S] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_PWRON1S_MASK,
 	},
 	[S2MPS11_IRQ_MRB] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S2MPS11_IRQ_MRB_MASK,
 	},
 	[S2MPS11_IRQ_RTC60S] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_RTC60S_MASK,
 	},
 	[S2MPS11_IRQ_RTCA1] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_RTCA1_MASK,
 	},
 	[S2MPS11_IRQ_RTCA2] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_RTCA2_MASK,
 	},
 	[S2MPS11_IRQ_SMPL] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_SMPL_MASK,
 	},
 	[S2MPS11_IRQ_RTC1S] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_RTC1S_MASK,
 	},
 	[S2MPS11_IRQ_WTSR] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S2MPS11_IRQ_WTSR_MASK,
 	},
 	[S2MPS11_IRQ_INT120C] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S2MPS11_IRQ_INT120C_MASK,
 	},
 	[S2MPS11_IRQ_INT140C] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S2MPS11_IRQ_INT140C_MASK,
 	},
 };
@@ -92,146 +92,146 @@
 
 static struct regmap_irq s5m8767_irqs[] = {
 	[S5M8767_IRQ_PWRR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_PWRR_MASK,
 	},
 	[S5M8767_IRQ_PWRF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_PWRF_MASK,
 	},
 	[S5M8767_IRQ_PWR1S] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_PWR1S_MASK,
 	},
 	[S5M8767_IRQ_JIGR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_JIGR_MASK,
 	},
 	[S5M8767_IRQ_JIGF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_JIGF_MASK,
 	},
 	[S5M8767_IRQ_LOWBAT2] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_LOWBAT2_MASK,
 	},
 	[S5M8767_IRQ_LOWBAT1] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8767_IRQ_LOWBAT1_MASK,
 	},
 	[S5M8767_IRQ_MRB] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8767_IRQ_MRB_MASK,
 	},
 	[S5M8767_IRQ_DVSOK2] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8767_IRQ_DVSOK2_MASK,
 	},
 	[S5M8767_IRQ_DVSOK3] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8767_IRQ_DVSOK3_MASK,
 	},
 	[S5M8767_IRQ_DVSOK4] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8767_IRQ_DVSOK4_MASK,
 	},
 	[S5M8767_IRQ_RTC60S] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_RTC60S_MASK,
 	},
 	[S5M8767_IRQ_RTCA1] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_RTCA1_MASK,
 	},
 	[S5M8767_IRQ_RTCA2] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_RTCA2_MASK,
 	},
 	[S5M8767_IRQ_SMPL] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_SMPL_MASK,
 	},
 	[S5M8767_IRQ_RTC1S] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_RTC1S_MASK,
 	},
 	[S5M8767_IRQ_WTSR] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8767_IRQ_WTSR_MASK,
 	},
 };
 
 static struct regmap_irq s5m8763_irqs[] = {
 	[S5M8763_IRQ_DCINF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_DCINF_MASK,
 	},
 	[S5M8763_IRQ_DCINR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_DCINR_MASK,
 	},
 	[S5M8763_IRQ_JIGF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_JIGF_MASK,
 	},
 	[S5M8763_IRQ_JIGR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_JIGR_MASK,
 	},
 	[S5M8763_IRQ_PWRONF] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_PWRONF_MASK,
 	},
 	[S5M8763_IRQ_PWRONR] = {
-		.reg_offset = 1,
+		.reg_offset = 0,
 		.mask = S5M8763_IRQ_PWRONR_MASK,
 	},
 	[S5M8763_IRQ_WTSREVNT] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8763_IRQ_WTSREVNT_MASK,
 	},
 	[S5M8763_IRQ_SMPLEVNT] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8763_IRQ_SMPLEVNT_MASK,
 	},
 	[S5M8763_IRQ_ALARM1] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8763_IRQ_ALARM1_MASK,
 	},
 	[S5M8763_IRQ_ALARM0] = {
-		.reg_offset = 2,
+		.reg_offset = 1,
 		.mask = S5M8763_IRQ_ALARM0_MASK,
 	},
 	[S5M8763_IRQ_ONKEY1S] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_ONKEY1S_MASK,
 	},
 	[S5M8763_IRQ_TOPOFFR] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_TOPOFFR_MASK,
 	},
 	[S5M8763_IRQ_DCINOVPR] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_DCINOVPR_MASK,
 	},
 	[S5M8763_IRQ_CHGRSTF] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_CHGRSTF_MASK,
 	},
 	[S5M8763_IRQ_DONER] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_DONER_MASK,
 	},
 	[S5M8763_IRQ_CHGFAULT] = {
-		.reg_offset = 3,
+		.reg_offset = 2,
 		.mask = S5M8763_IRQ_CHGFAULT_MASK,
 	},
 	[S5M8763_IRQ_LOBAT1] = {
-		.reg_offset = 4,
+		.reg_offset = 3,
 		.mask = S5M8763_IRQ_LOBAT1_MASK,
 	},
 	[S5M8763_IRQ_LOBAT2] = {
-		.reg_offset = 4,
+		.reg_offset = 3,
 		.mask = S5M8763_IRQ_LOBAT2_MASK,
 	},
 };
diff --git a/drivers/mfd/sta2x11-mfd.c b/drivers/mfd/sta2x11-mfd.c
index d6284ca..1225dcb 100644
--- a/drivers/mfd/sta2x11-mfd.c
+++ b/drivers/mfd/sta2x11-mfd.c
@@ -1,6 +1,6 @@
 /*
  * Copyright (c) 2009-2011 Wind River Systems, Inc.
- * Copyright (c) 2011 ST Microelectronics (Alessandro Rubini)
+ * Copyright (c) 2011 ST Microelectronics (Alessandro Rubini, Davide Ciminaghi)
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -27,21 +27,28 @@
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/pci.h>
-#include <linux/debugfs.h>
 #include <linux/seq_file.h>
 #include <linux/platform_device.h>
 #include <linux/mfd/core.h>
 #include <linux/mfd/sta2x11-mfd.h>
+#include <linux/regmap.h>
 
 #include <asm/sta2x11.h>
 
+static inline int __reg_within_range(unsigned int r,
+				     unsigned int start,
+				     unsigned int end)
+{
+	return ((r >= start) && (r <= end));
+}
+
 /* This describes STA2X11 MFD chip for us, we may have several */
 struct sta2x11_mfd {
 	struct sta2x11_instance *instance;
-	spinlock_t lock;
+	struct regmap *regmap[sta2x11_n_mfd_plat_devs];
+	spinlock_t lock[sta2x11_n_mfd_plat_devs];
 	struct list_head list;
-	void __iomem *sctl_regs;
-	void __iomem *apbreg_regs;
+	void __iomem *regs[sta2x11_n_mfd_plat_devs];
 };
 
 static LIST_HEAD(sta2x11_mfd_list);
@@ -71,6 +78,7 @@
 
 static int sta2x11_mfd_add(struct pci_dev *pdev, gfp_t flags)
 {
+	int i;
 	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
 	struct sta2x11_instance *instance;
 
@@ -83,7 +91,8 @@
 	if (!mfd)
 		return -ENOMEM;
 	INIT_LIST_HEAD(&mfd->list);
-	spin_lock_init(&mfd->lock);
+	for (i = 0; i < ARRAY_SIZE(mfd->lock); i++)
+		spin_lock_init(&mfd->lock[i]);
 	mfd->instance = instance;
 	list_add(&mfd->list, &sta2x11_mfd_list);
 	return 0;
@@ -100,161 +109,276 @@
 	return 0;
 }
 
-/* These two functions are exported and are not expected to fail */
-u32 sta2x11_sctl_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+/* This function is exported and is not expected to fail */
+u32 __sta2x11_mfd_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val,
+		       enum sta2x11_mfd_plat_dev index)
 {
 	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
 	u32 r;
 	unsigned long flags;
+	void __iomem *regs;
 
 	if (!mfd) {
 		dev_warn(&pdev->dev, ": can't access sctl regs\n");
 		return 0;
 	}
-	if (!mfd->sctl_regs) {
+
+	regs = mfd->regs[index];
+	if (!regs) {
 		dev_warn(&pdev->dev, ": system ctl not initialized\n");
 		return 0;
 	}
-	spin_lock_irqsave(&mfd->lock, flags);
-	r = readl(mfd->sctl_regs + reg);
+	spin_lock_irqsave(&mfd->lock[index], flags);
+	r = readl(regs + reg);
 	r &= ~mask;
 	r |= val;
 	if (mask)
-		writel(r, mfd->sctl_regs + reg);
-	spin_unlock_irqrestore(&mfd->lock, flags);
+		writel(r, regs + reg);
+	spin_unlock_irqrestore(&mfd->lock[index], flags);
 	return r;
 }
-EXPORT_SYMBOL(sta2x11_sctl_mask);
+EXPORT_SYMBOL(__sta2x11_mfd_mask);
 
-u32 sta2x11_apbreg_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+int sta2x11_mfd_get_regs_data(struct platform_device *dev,
+			      enum sta2x11_mfd_plat_dev index,
+			      void __iomem **regs,
+			      spinlock_t **lock)
 {
-	struct sta2x11_mfd *mfd = sta2x11_mfd_find(pdev);
-	u32 r;
-	unsigned long flags;
+	struct pci_dev *pdev = *(struct pci_dev **)(dev->dev.platform_data);
+	struct sta2x11_mfd *mfd;
 
-	if (!mfd) {
-		dev_warn(&pdev->dev, ": can't access apb regs\n");
-		return 0;
-	}
-	if (!mfd->apbreg_regs) {
-		dev_warn(&pdev->dev, ": apb bridge not initialized\n");
-		return 0;
-	}
-	spin_lock_irqsave(&mfd->lock, flags);
-	r = readl(mfd->apbreg_regs + reg);
-	r &= ~mask;
-	r |= val;
-	if (mask)
-		writel(r, mfd->apbreg_regs + reg);
-	spin_unlock_irqrestore(&mfd->lock, flags);
-	return r;
+	if (!pdev)
+		return -ENODEV;
+	mfd = sta2x11_mfd_find(pdev);
+	if (!mfd)
+		return -ENODEV;
+	if (index >= sta2x11_n_mfd_plat_devs)
+		return -ENODEV;
+	*regs = mfd->regs[index];
+	*lock = &mfd->lock[index];
+	pr_debug("%s %d *regs = %p\n", __func__, __LINE__, *regs);
+	return *regs ? 0 : -ENODEV;
 }
-EXPORT_SYMBOL(sta2x11_apbreg_mask);
+EXPORT_SYMBOL(sta2x11_mfd_get_regs_data);
 
-/* Two debugfs files, for our registers (FIXME: one instance only) */
-#define REG(regname) {.name = #regname, .offset = SCTL_ ## regname}
-static struct debugfs_reg32 sta2x11_sctl_regs[] = {
-	REG(SCCTL), REG(ARMCFG), REG(SCPLLCTL), REG(SCPLLFCTRL),
-	REG(SCRESFRACT), REG(SCRESCTRL1), REG(SCRESXTRL2), REG(SCPEREN0),
-	REG(SCPEREN1), REG(SCPEREN2), REG(SCGRST), REG(SCPCIPMCR1),
-	REG(SCPCIPMCR2), REG(SCPCIPMSR1), REG(SCPCIPMSR2), REG(SCPCIPMSR3),
-	REG(SCINTREN), REG(SCRISR), REG(SCCLKSTAT0), REG(SCCLKSTAT1),
-	REG(SCCLKSTAT2), REG(SCRSTSTA),
-};
-#undef REG
+/*
+ * Special sta2x11-mfd regmap lock/unlock functions
+ */
 
-static struct debugfs_regset32 sctl_regset = {
-	.regs = sta2x11_sctl_regs,
-	.nregs = ARRAY_SIZE(sta2x11_sctl_regs),
+static void sta2x11_regmap_lock(void *__lock)
+{
+	spinlock_t *lock = __lock;
+	spin_lock(lock);
+}
+
+static void sta2x11_regmap_unlock(void *__lock)
+{
+	spinlock_t *lock = __lock;
+	spin_unlock(lock);
+}
+
+/* OTP (one time programmable registers do not require locking */
+static void sta2x11_regmap_nolock(void *__lock)
+{
+}
+
+static const char *sta2x11_mfd_names[sta2x11_n_mfd_plat_devs] = {
+	[sta2x11_sctl] = STA2X11_MFD_SCTL_NAME,
+	[sta2x11_apbreg] = STA2X11_MFD_APBREG_NAME,
+	[sta2x11_apb_soc_regs] = STA2X11_MFD_APB_SOC_REGS_NAME,
+	[sta2x11_scr] = STA2X11_MFD_SCR_NAME,
 };
 
-#define REG(regname) {.name = #regname, .offset = regname}
-static struct debugfs_reg32 sta2x11_apbreg_regs[] = {
-	REG(APBREG_BSR), REG(APBREG_PAER), REG(APBREG_PWAC), REG(APBREG_PRAC),
-	REG(APBREG_PCG), REG(APBREG_PUR), REG(APBREG_EMU_PCG),
-};
-#undef REG
+static bool sta2x11_sctl_writeable_reg(struct device *dev, unsigned int reg)
+{
+	return !__reg_within_range(reg, SCTL_SCPCIECSBRST, SCTL_SCRSTSTA);
+}
 
-static struct debugfs_regset32 apbreg_regset = {
-	.regs = sta2x11_apbreg_regs,
-	.nregs = ARRAY_SIZE(sta2x11_apbreg_regs),
+static struct regmap_config sta2x11_sctl_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.lock = sta2x11_regmap_lock,
+	.unlock = sta2x11_regmap_unlock,
+	.max_register = SCTL_SCRSTSTA,
+	.writeable_reg = sta2x11_sctl_writeable_reg,
 };
 
-static struct dentry *sta2x11_sctl_debugfs;
-static struct dentry *sta2x11_apbreg_debugfs;
+static bool sta2x11_scr_readable_reg(struct device *dev, unsigned int reg)
+{
+	return (reg == STA2X11_SECR_CR) ||
+		__reg_within_range(reg, STA2X11_SECR_FVR0, STA2X11_SECR_FVR1);
+}
 
-/* Probe for the two platform devices */
-static int sta2x11_sctl_probe(struct platform_device *dev)
+static bool sta2x11_scr_writeable_reg(struct device *dev, unsigned int reg)
+{
+	return false;
+}
+
+static struct regmap_config sta2x11_scr_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.lock = sta2x11_regmap_nolock,
+	.unlock = sta2x11_regmap_nolock,
+	.max_register = STA2X11_SECR_FVR1,
+	.readable_reg = sta2x11_scr_readable_reg,
+	.writeable_reg = sta2x11_scr_writeable_reg,
+};
+
+static bool sta2x11_apbreg_readable_reg(struct device *dev, unsigned int reg)
+{
+	/* Two blocks (CAN and MLB, SARAC) 0x100 bytes apart */
+	if (reg >= APBREG_BSR_SARAC)
+		reg -= APBREG_BSR_SARAC;
+	switch (reg) {
+	case APBREG_BSR:
+	case APBREG_PAER:
+	case APBREG_PWAC:
+	case APBREG_PRAC:
+	case APBREG_PCG:
+	case APBREG_PUR:
+	case APBREG_EMU_PCG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool sta2x11_apbreg_writeable_reg(struct device *dev, unsigned int reg)
+{
+	if (reg >= APBREG_BSR_SARAC)
+		reg -= APBREG_BSR_SARAC;
+	if (!sta2x11_apbreg_readable_reg(dev, reg))
+		return false;
+	return reg != APBREG_PAER;
+}
+
+static struct regmap_config sta2x11_apbreg_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.lock = sta2x11_regmap_lock,
+	.unlock = sta2x11_regmap_unlock,
+	.max_register = APBREG_EMU_PCG_SARAC,
+	.readable_reg = sta2x11_apbreg_readable_reg,
+	.writeable_reg = sta2x11_apbreg_writeable_reg,
+};
+
+static bool sta2x11_apb_soc_regs_readable_reg(struct device *dev,
+					      unsigned int reg)
+{
+	return reg <= PCIE_SoC_INT_ROUTER_STATUS3_REG ||
+		__reg_within_range(reg, DMA_IP_CTRL_REG, SPARE3_RESERVED) ||
+		__reg_within_range(reg, MASTER_LOCK_REG,
+				   SYSTEM_CONFIG_STATUS_REG) ||
+		reg == MSP_CLK_CTRL_REG ||
+		__reg_within_range(reg, COMPENSATION_REG1, TEST_CTL_REG);
+}
+
+static bool sta2x11_apb_soc_regs_writeable_reg(struct device *dev,
+					       unsigned int reg)
+{
+	if (!sta2x11_apb_soc_regs_readable_reg(dev, reg))
+		return false;
+	switch (reg) {
+	case PCIE_COMMON_CLOCK_CONFIG_0_4_0:
+	case SYSTEM_CONFIG_STATUS_REG:
+	case COMPENSATION_REG1:
+	case PCIE_SoC_INT_ROUTER_STATUS0_REG...PCIE_SoC_INT_ROUTER_STATUS3_REG:
+	case PCIE_PM_STATUS_0_PORT_0_4...PCIE_PM_STATUS_7_0_EP4:
+		return false;
+	default:
+		return true;
+	}
+}
+
+static struct regmap_config sta2x11_apb_soc_regs_regmap_config = {
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+	.lock = sta2x11_regmap_lock,
+	.unlock = sta2x11_regmap_unlock,
+	.max_register = TEST_CTL_REG,
+	.readable_reg = sta2x11_apb_soc_regs_readable_reg,
+	.writeable_reg = sta2x11_apb_soc_regs_writeable_reg,
+};
+
+static struct regmap_config *
+sta2x11_mfd_regmap_configs[sta2x11_n_mfd_plat_devs] = {
+	[sta2x11_sctl] = &sta2x11_sctl_regmap_config,
+	[sta2x11_apbreg] = &sta2x11_apbreg_regmap_config,
+	[sta2x11_apb_soc_regs] = &sta2x11_apb_soc_regs_regmap_config,
+	[sta2x11_scr] = &sta2x11_scr_regmap_config,
+};
+
+/* Probe for the four platform devices */
+
+static int sta2x11_mfd_platform_probe(struct platform_device *dev,
+				      enum sta2x11_mfd_plat_dev index)
 {
 	struct pci_dev **pdev;
 	struct sta2x11_mfd *mfd;
 	struct resource *res;
+	const char *name = sta2x11_mfd_names[index];
+	struct regmap_config *regmap_config = sta2x11_mfd_regmap_configs[index];
 
 	pdev = dev->dev.platform_data;
 	mfd = sta2x11_mfd_find(*pdev);
 	if (!mfd)
 		return -ENODEV;
+	if (!regmap_config)
+		return -ENODEV;
 
 	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
 	if (!res)
 		return -ENOMEM;
 
-	if (!request_mem_region(res->start, resource_size(res),
-				"sta2x11-sctl"))
+	if (!request_mem_region(res->start, resource_size(res), name))
 		return -EBUSY;
 
-	mfd->sctl_regs = ioremap(res->start, resource_size(res));
-	if (!mfd->sctl_regs) {
+	mfd->regs[index] = ioremap(res->start, resource_size(res));
+	if (!mfd->regs[index]) {
 		release_mem_region(res->start, resource_size(res));
 		return -ENOMEM;
 	}
-	sctl_regset.base = mfd->sctl_regs;
-	sta2x11_sctl_debugfs = debugfs_create_regset32("sta2x11-sctl",
-						  S_IFREG | S_IRUGO,
-						  NULL, &sctl_regset);
+	regmap_config->lock_arg = &mfd->lock;
+	/*
+	   No caching, registers could be reached both via regmap and via
+	   void __iomem *
+	*/
+	regmap_config->cache_type = REGCACHE_NONE;
+	mfd->regmap[index] = devm_regmap_init_mmio(&dev->dev, mfd->regs[index],
+						   regmap_config);
+	WARN_ON(!mfd->regmap[index]);
+
 	return 0;
 }
 
+static int sta2x11_sctl_probe(struct platform_device *dev)
+{
+	return sta2x11_mfd_platform_probe(dev, sta2x11_sctl);
+}
+
 static int sta2x11_apbreg_probe(struct platform_device *dev)
 {
-	struct pci_dev **pdev;
-	struct sta2x11_mfd *mfd;
-	struct resource *res;
-
-	pdev = dev->dev.platform_data;
-	dev_dbg(&dev->dev, "%s: pdata is %p\n", __func__, pdev);
-	dev_dbg(&dev->dev, "%s: *pdata is %p\n", __func__, *pdev);
-
-	mfd = sta2x11_mfd_find(*pdev);
-	if (!mfd)
-		return -ENODEV;
-
-	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
-	if (!res)
-		return -ENOMEM;
-
-	if (!request_mem_region(res->start, resource_size(res),
-				"sta2x11-apbreg"))
-		return -EBUSY;
-
-	mfd->apbreg_regs = ioremap(res->start, resource_size(res));
-	if (!mfd->apbreg_regs) {
-		release_mem_region(res->start, resource_size(res));
-		return -ENOMEM;
-	}
-	dev_dbg(&dev->dev, "%s: regbase %p\n", __func__, mfd->apbreg_regs);
-
-	apbreg_regset.base = mfd->apbreg_regs;
-	sta2x11_apbreg_debugfs = debugfs_create_regset32("sta2x11-apbreg",
-						  S_IFREG | S_IRUGO,
-						  NULL, &apbreg_regset);
-	return 0;
+	return sta2x11_mfd_platform_probe(dev, sta2x11_apbreg);
 }
 
-/* The two platform drivers */
+static int sta2x11_apb_soc_regs_probe(struct platform_device *dev)
+{
+	return sta2x11_mfd_platform_probe(dev, sta2x11_apb_soc_regs);
+}
+
+static int sta2x11_scr_probe(struct platform_device *dev)
+{
+	return sta2x11_mfd_platform_probe(dev, sta2x11_scr);
+}
+
+/* The three platform drivers */
 static struct platform_driver sta2x11_sctl_platform_driver = {
 	.driver = {
-		.name	= "sta2x11-sctl",
+		.name	= STA2X11_MFD_SCTL_NAME,
 		.owner	= THIS_MODULE,
 	},
 	.probe		= sta2x11_sctl_probe,
@@ -268,7 +392,7 @@
 
 static struct platform_driver sta2x11_platform_driver = {
 	.driver = {
-		.name	= "sta2x11-apbreg",
+		.name	= STA2X11_MFD_APBREG_NAME,
 		.owner	= THIS_MODULE,
 	},
 	.probe		= sta2x11_apbreg_probe,
@@ -280,13 +404,44 @@
 	return platform_driver_register(&sta2x11_platform_driver);
 }
 
+static struct platform_driver sta2x11_apb_soc_regs_platform_driver = {
+	.driver = {
+		.name	= STA2X11_MFD_APB_SOC_REGS_NAME,
+		.owner	= THIS_MODULE,
+	},
+	.probe		= sta2x11_apb_soc_regs_probe,
+};
+
+static int __init sta2x11_apb_soc_regs_init(void)
+{
+	pr_info("%s\n", __func__);
+	return platform_driver_register(&sta2x11_apb_soc_regs_platform_driver);
+}
+
+static struct platform_driver sta2x11_scr_platform_driver = {
+	.driver = {
+		.name = STA2X11_MFD_SCR_NAME,
+		.owner = THIS_MODULE,
+	},
+	.probe = sta2x11_scr_probe,
+};
+
+static int __init sta2x11_scr_init(void)
+{
+	pr_info("%s\n", __func__);
+	return platform_driver_register(&sta2x11_scr_platform_driver);
+}
+
+
 /*
- * What follows is the PCI device that hosts the above two pdevs.
+ * What follows are the PCI devices that host the above pdevs.
  * Each logic block is 4kB and they are all consecutive: we use this info.
  */
 
-/* Bar 0 */
-enum bar0_cells {
+/* Mfd 0 device */
+
+/* Mfd 0, Bar 0 */
+enum mfd0_bar0_cells {
 	STA2X11_GPIO_0 = 0,
 	STA2X11_GPIO_1,
 	STA2X11_GPIO_2,
@@ -295,8 +450,8 @@
 	STA2X11_SCR,
 	STA2X11_TIME,
 };
-/* Bar 1 */
-enum bar1_cells {
+/* Mfd 0 , Bar 1 */
+enum mfd0_bar1_cells {
 	STA2X11_APBREG = 0,
 };
 #define CELL_4K(_name, _cell) { \
@@ -307,40 +462,71 @@
 
 static const struct resource gpio_resources[] = {
 	{
-		.name = "sta2x11_gpio", /* 4 consecutive cells, 1 driver */
+		/* 4 consecutive cells, 1 driver */
+		.name = STA2X11_MFD_GPIO_NAME,
 		.start = 0,
 		.end = (4 * 4096) - 1,
 		.flags = IORESOURCE_MEM,
 	}
 };
 static const struct resource sctl_resources[] = {
-	CELL_4K("sta2x11-sctl", STA2X11_SCTL),
+	CELL_4K(STA2X11_MFD_SCTL_NAME, STA2X11_SCTL),
 };
 static const struct resource scr_resources[] = {
-	CELL_4K("sta2x11-scr", STA2X11_SCR),
+	CELL_4K(STA2X11_MFD_SCR_NAME, STA2X11_SCR),
 };
 static const struct resource time_resources[] = {
-	CELL_4K("sta2x11-time", STA2X11_TIME),
+	CELL_4K(STA2X11_MFD_TIME_NAME, STA2X11_TIME),
 };
 
 static const struct resource apbreg_resources[] = {
-	CELL_4K("sta2x11-apbreg", STA2X11_APBREG),
+	CELL_4K(STA2X11_MFD_APBREG_NAME, STA2X11_APBREG),
 };
 
 #define DEV(_name, _r) \
 	{ .name = _name, .num_resources = ARRAY_SIZE(_r), .resources = _r, }
 
-static struct mfd_cell sta2x11_mfd_bar0[] = {
-	DEV("sta2x11-gpio", gpio_resources), /* offset 0: we add pdata later */
-	DEV("sta2x11-sctl", sctl_resources),
-	DEV("sta2x11-scr", scr_resources),
-	DEV("sta2x11-time", time_resources),
+static struct mfd_cell sta2x11_mfd0_bar0[] = {
+	/* offset 0: we add pdata later */
+	DEV(STA2X11_MFD_GPIO_NAME, gpio_resources),
+	DEV(STA2X11_MFD_SCTL_NAME, sctl_resources),
+	DEV(STA2X11_MFD_SCR_NAME,  scr_resources),
+	DEV(STA2X11_MFD_TIME_NAME, time_resources),
 };
 
-static struct mfd_cell sta2x11_mfd_bar1[] = {
-	DEV("sta2x11-apbreg", apbreg_resources),
+static struct mfd_cell sta2x11_mfd0_bar1[] = {
+	DEV(STA2X11_MFD_APBREG_NAME, apbreg_resources),
 };
 
+/* Mfd 1 devices */
+
+/* Mfd 1, Bar 0 */
+enum mfd1_bar0_cells {
+	STA2X11_VIC = 0,
+};
+
+/* Mfd 1, Bar 1 */
+enum mfd1_bar1_cells {
+	STA2X11_APB_SOC_REGS = 0,
+};
+
+static const __devinitconst struct resource vic_resources[] = {
+	CELL_4K(STA2X11_MFD_VIC_NAME, STA2X11_VIC),
+};
+
+static const __devinitconst struct resource apb_soc_regs_resources[] = {
+	CELL_4K(STA2X11_MFD_APB_SOC_REGS_NAME, STA2X11_APB_SOC_REGS),
+};
+
+static __devinitdata struct mfd_cell sta2x11_mfd1_bar0[] = {
+	DEV(STA2X11_MFD_VIC_NAME, vic_resources),
+};
+
+static __devinitdata struct mfd_cell sta2x11_mfd1_bar1[] = {
+	DEV(STA2X11_MFD_APB_SOC_REGS_NAME, apb_soc_regs_resources),
+};
+
+
 static int sta2x11_mfd_suspend(struct pci_dev *pdev, pm_message_t state)
 {
 	pci_save_state(pdev);
@@ -363,11 +549,63 @@
 	return 0;
 }
 
+struct sta2x11_mfd_bar_setup_data {
+	struct mfd_cell *cells;
+	int ncells;
+};
+
+struct sta2x11_mfd_setup_data {
+	struct sta2x11_mfd_bar_setup_data bars[2];
+};
+
+#define STA2X11_MFD0 0
+#define STA2X11_MFD1 1
+
+static struct sta2x11_mfd_setup_data mfd_setup_data[] = {
+	/* Mfd 0: gpio, sctl, scr, timers / apbregs */
+	[STA2X11_MFD0] = {
+		.bars = {
+			[0] = {
+				.cells = sta2x11_mfd0_bar0,
+				.ncells = ARRAY_SIZE(sta2x11_mfd0_bar0),
+			},
+			[1] = {
+				.cells = sta2x11_mfd0_bar1,
+				.ncells = ARRAY_SIZE(sta2x11_mfd0_bar1),
+			},
+		},
+	},
+	/* Mfd 1: vic / apb-soc-regs */
+	[STA2X11_MFD1] = {
+		.bars = {
+			[0] = {
+				.cells = sta2x11_mfd1_bar0,
+				.ncells = ARRAY_SIZE(sta2x11_mfd1_bar0),
+			},
+			[1] = {
+				.cells = sta2x11_mfd1_bar1,
+				.ncells = ARRAY_SIZE(sta2x11_mfd1_bar1),
+			},
+		},
+	},
+};
+
+static void sta2x11_mfd_setup(struct pci_dev *pdev,
+			      struct sta2x11_mfd_setup_data *sd)
+{
+	int i, j;
+	for (i = 0; i < ARRAY_SIZE(sd->bars); i++)
+		for (j = 0; j < sd->bars[i].ncells; j++) {
+			sd->bars[i].cells[j].pdata_size = sizeof(pdev);
+			sd->bars[i].cells[j].platform_data = &pdev;
+		}
+}
+
 static int sta2x11_mfd_probe(struct pci_dev *pdev,
-				       const struct pci_device_id *pci_id)
+			     const struct pci_device_id *pci_id)
 {
 	int err, i;
-	struct sta2x11_gpio_pdata *gpio_data;
+	struct sta2x11_mfd_setup_data *setup_data;
 
 	dev_info(&pdev->dev, "%s\n", __func__);
 
@@ -381,46 +619,29 @@
 	if (err)
 		dev_info(&pdev->dev, "Enable msi failed\n");
 
-	/* Read gpio config data as pci device's platform data */
-	gpio_data = dev_get_platdata(&pdev->dev);
-	if (!gpio_data)
-		dev_warn(&pdev->dev, "no gpio configuration\n");
-
-	dev_dbg(&pdev->dev, "%s, gpio_data = %p (%p)\n", __func__,
-		gpio_data, &gpio_data);
-	dev_dbg(&pdev->dev, "%s, pdev = %p (%p)\n", __func__,
-		pdev, &pdev);
+	setup_data = pci_id->device == PCI_DEVICE_ID_STMICRO_GPIO ?
+		&mfd_setup_data[STA2X11_MFD0] :
+		&mfd_setup_data[STA2X11_MFD1];
 
 	/* platform data is the pci device for all of them */
-	for (i = 0; i < ARRAY_SIZE(sta2x11_mfd_bar0); i++) {
-		sta2x11_mfd_bar0[i].pdata_size = sizeof(pdev);
-		sta2x11_mfd_bar0[i].platform_data = &pdev;
-	}
-	sta2x11_mfd_bar1[0].pdata_size = sizeof(pdev);
-	sta2x11_mfd_bar1[0].platform_data = &pdev;
+	sta2x11_mfd_setup(pdev, setup_data);
 
 	/* Record this pdev before mfd_add_devices: their probe looks for it */
-	sta2x11_mfd_add(pdev, GFP_ATOMIC);
+	if (!sta2x11_mfd_find(pdev))
+		sta2x11_mfd_add(pdev, GFP_ATOMIC);
 
-
-	err = mfd_add_devices(&pdev->dev, -1,
-			      sta2x11_mfd_bar0,
-			      ARRAY_SIZE(sta2x11_mfd_bar0),
-			      &pdev->resource[0],
-			      0, NULL);
-	if (err) {
-		dev_err(&pdev->dev, "mfd_add_devices[0] failed: %d\n", err);
-		goto err_disable;
-	}
-
-	err = mfd_add_devices(&pdev->dev, -1,
-			      sta2x11_mfd_bar1,
-			      ARRAY_SIZE(sta2x11_mfd_bar1),
-			      &pdev->resource[1],
-			      0, NULL);
-	if (err) {
-		dev_err(&pdev->dev, "mfd_add_devices[1] failed: %d\n", err);
-		goto err_disable;
+	/* Just 2 bars for all mfd's at present */
+	for (i = 0; i < 2; i++) {
+		err = mfd_add_devices(&pdev->dev, -1,
+				      setup_data->bars[i].cells,
+				      setup_data->bars[i].ncells,
+				      &pdev->resource[i],
+				      0, NULL);
+		if (err) {
+			dev_err(&pdev->dev,
+				"mfd_add_devices[%d] failed: %d\n", i, err);
+			goto err_disable;
+		}
 	}
 
 	return 0;
@@ -434,6 +655,7 @@
 
 static DEFINE_PCI_DEVICE_TABLE(sta2x11_mfd_tbl) = {
 	{PCI_DEVICE(PCI_VENDOR_ID_STMICRO, PCI_DEVICE_ID_STMICRO_GPIO)},
+	{PCI_DEVICE(PCI_VENDOR_ID_STMICRO, PCI_DEVICE_ID_STMICRO_VIC)},
 	{0,},
 };
 
@@ -459,6 +681,8 @@
  */
 subsys_initcall(sta2x11_apbreg_init);
 subsys_initcall(sta2x11_sctl_init);
+subsys_initcall(sta2x11_apb_soc_regs_init);
+subsys_initcall(sta2x11_scr_init);
 rootfs_initcall(sta2x11_mfd_init);
 
 MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/stmpe-i2c.c b/drivers/mfd/stmpe-i2c.c
index 36df187..fd5fcb6 100644
--- a/drivers/mfd/stmpe-i2c.c
+++ b/drivers/mfd/stmpe-i2c.c
@@ -82,11 +82,13 @@
 MODULE_DEVICE_TABLE(i2c, stmpe_id);
 
 static struct i2c_driver stmpe_i2c_driver = {
-	.driver.name	= "stmpe-i2c",
-	.driver.owner	= THIS_MODULE,
+	.driver = {
+		.name = "stmpe-i2c",
+		.owner = THIS_MODULE,
 #ifdef CONFIG_PM
-	.driver.pm	= &stmpe_dev_pm_ops,
+		.pm = &stmpe_dev_pm_ops,
 #endif
+	},
 	.probe		= stmpe_i2c_probe,
 	.remove		= stmpe_i2c_remove,
 	.id_table	= stmpe_i2c_id,
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index 79e88d1..1963619 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -7,11 +7,15 @@
  * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
  */
 
+#include <linux/err.h>
 #include <linux/gpio.h>
 #include <linux/export.h>
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/pm.h>
 #include <linux/slab.h>
 #include <linux/mfd/core.h>
@@ -312,14 +316,10 @@
 static struct resource stmpe_keypad_resources[] = {
 	{
 		.name	= "KEYPAD",
-		.start	= 0,
-		.end	= 0,
 		.flags	= IORESOURCE_IRQ,
 	},
 	{
 		.name	= "KEYPAD_OVER",
-		.start	= 1,
-		.end	= 1,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -399,14 +399,10 @@
 static struct resource stmpe_ts_resources[] = {
 	{
 		.name	= "TOUCH_DET",
-		.start	= 0,
-		.end	= 0,
 		.flags	= IORESOURCE_IRQ,
 	},
 	{
 		.name	= "FIFO_TH",
-		.start	= 1,
-		.end	= 1,
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -528,12 +524,12 @@
 static struct stmpe_variant_block stmpe1601_blocks[] = {
 	{
 		.cell	= &stmpe_gpio_cell,
-		.irq	= STMPE24XX_IRQ_GPIOC,
+		.irq	= STMPE1601_IRQ_GPIOC,
 		.block	= STMPE_BLOCK_GPIO,
 	},
 	{
 		.cell	= &stmpe_keypad_cell,
-		.irq	= STMPE24XX_IRQ_KEYPAD,
+		.irq	= STMPE1601_IRQ_KEYPAD,
 		.block	= STMPE_BLOCK_KEYPAD,
 	},
 };
@@ -767,7 +763,9 @@
 	int i;
 
 	if (variant->id_val == STMPE801_ID) {
-		handle_nested_irq(stmpe->irq_base);
+		int base = irq_create_mapping(stmpe->domain, 0);
+
+		handle_nested_irq(base);
 		return IRQ_HANDLED;
 	}
 
@@ -788,8 +786,9 @@
 		while (status) {
 			int bit = __ffs(status);
 			int line = bank * 8 + bit;
+			int nestedirq = irq_create_mapping(stmpe->domain, line);
 
-			handle_nested_irq(stmpe->irq_base + line);
+			handle_nested_irq(nestedirq);
 			status &= ~(1 << bit);
 		}
 
@@ -830,7 +829,7 @@
 static void stmpe_irq_mask(struct irq_data *data)
 {
 	struct stmpe *stmpe = irq_data_get_irq_chip_data(data);
-	int offset = data->irq - stmpe->irq_base;
+	int offset = data->hwirq;
 	int regoffset = offset / 8;
 	int mask = 1 << (offset % 8);
 
@@ -840,7 +839,7 @@
 static void stmpe_irq_unmask(struct irq_data *data)
 {
 	struct stmpe *stmpe = irq_data_get_irq_chip_data(data);
-	int offset = data->irq - stmpe->irq_base;
+	int offset = data->hwirq;
 	int regoffset = offset / 8;
 	int mask = 1 << (offset % 8);
 
@@ -855,43 +854,59 @@
 	.irq_unmask		= stmpe_irq_unmask,
 };
 
-static int __devinit stmpe_irq_init(struct stmpe *stmpe)
+static int stmpe_irq_map(struct irq_domain *d, unsigned int virq,
+                                irq_hw_number_t hwirq)
 {
+	struct stmpe *stmpe = d->host_data;
 	struct irq_chip *chip = NULL;
-	int num_irqs = stmpe->variant->num_irqs;
-	int base = stmpe->irq_base;
-	int irq;
 
 	if (stmpe->variant->id_val != STMPE801_ID)
 		chip = &stmpe_irq_chip;
 
-	for (irq = base; irq < base + num_irqs; irq++) {
-		irq_set_chip_data(irq, stmpe);
-		irq_set_chip_and_handler(irq, chip, handle_edge_irq);
-		irq_set_nested_thread(irq, 1);
+	irq_set_chip_data(virq, stmpe);
+	irq_set_chip_and_handler(virq, chip, handle_edge_irq);
+	irq_set_nested_thread(virq, 1);
 #ifdef CONFIG_ARM
-		set_irq_flags(irq, IRQF_VALID);
+	set_irq_flags(virq, IRQF_VALID);
 #else
-		irq_set_noprobe(irq);
+	irq_set_noprobe(virq);
 #endif
-	}
 
 	return 0;
 }
 
-static void stmpe_irq_remove(struct stmpe *stmpe)
+static void stmpe_irq_unmap(struct irq_domain *d, unsigned int virq)
 {
-	int num_irqs = stmpe->variant->num_irqs;
-	int base = stmpe->irq_base;
-	int irq;
-
-	for (irq = base; irq < base + num_irqs; irq++) {
 #ifdef CONFIG_ARM
-		set_irq_flags(irq, 0);
+		set_irq_flags(virq, 0);
 #endif
-		irq_set_chip_and_handler(irq, NULL, NULL);
-		irq_set_chip_data(irq, NULL);
+		irq_set_chip_and_handler(virq, NULL, NULL);
+		irq_set_chip_data(virq, NULL);
+}
+
+static struct irq_domain_ops stmpe_irq_ops = {
+        .map    = stmpe_irq_map,
+        .unmap  = stmpe_irq_unmap,
+        .xlate  = irq_domain_xlate_twocell,
+};
+
+static int __devinit stmpe_irq_init(struct stmpe *stmpe,
+				struct device_node *np)
+{
+	int base = 0;
+	int num_irqs = stmpe->variant->num_irqs;
+
+	if (!np)
+		base = stmpe->irq_base;
+
+	stmpe->domain = irq_domain_add_simple(np, num_irqs, base,
+					      &stmpe_irq_ops, stmpe);
+	if (!stmpe->domain) {
+		dev_err(stmpe->dev, "Failed to create irqdomain\n");
+		return -ENOSYS;
 	}
+
+	return 0;
 }
 
 static int __devinit stmpe_chip_init(struct stmpe *stmpe)
@@ -942,13 +957,6 @@
 			else
 				icr |= STMPE_ICR_LSB_HIGH;
 		}
-
-		if (stmpe->pdata->irq_invert_polarity) {
-			if (id == STMPE801_ID)
-				icr ^= STMPE801_REG_SYS_CTRL_INT_HI;
-			else
-				icr ^= STMPE_ICR_LSB_HIGH;
-		}
 	}
 
 	if (stmpe->pdata->autosleep) {
@@ -961,10 +969,10 @@
 }
 
 static int __devinit stmpe_add_device(struct stmpe *stmpe,
-				      struct mfd_cell *cell, int irq)
+				      struct mfd_cell *cell)
 {
 	return mfd_add_devices(stmpe->dev, stmpe->pdata->id, cell, 1,
-			       NULL, stmpe->irq_base + irq, NULL);
+			       NULL, stmpe->irq_base, stmpe->domain);
 }
 
 static int __devinit stmpe_devices_init(struct stmpe *stmpe)
@@ -972,7 +980,7 @@
 	struct stmpe_variant_info *variant = stmpe->variant;
 	unsigned int platform_blocks = stmpe->pdata->blocks;
 	int ret = -EINVAL;
-	int i;
+	int i, j;
 
 	for (i = 0; i < variant->num_blocks; i++) {
 		struct stmpe_variant_block *block = &variant->blocks[i];
@@ -980,8 +988,17 @@
 		if (!(platform_blocks & block->block))
 			continue;
 
+		for (j = 0; j < block->cell->num_resources; j++) {
+			struct resource *res =
+				(struct resource *) &block->cell->resources[j];
+
+			/* Dynamically fill in a variant's IRQ. */
+			if (res->flags & IORESOURCE_IRQ)
+				res->start = res->end = block->irq + j;
+		}
+
 		platform_blocks &= ~block->block;
-		ret = stmpe_add_device(stmpe, block->cell, block->irq);
+		ret = stmpe_add_device(stmpe, block->cell);
 		if (ret)
 			return ret;
 	}
@@ -994,17 +1011,56 @@
 	return ret;
 }
 
+void __devinit stmpe_of_probe(struct stmpe_platform_data *pdata,
+			struct device_node *np)
+{
+	struct device_node *child;
+
+	pdata->id = -1;
+	pdata->irq_trigger = IRQF_TRIGGER_NONE;
+
+	of_property_read_u32(np, "st,autosleep-timeout",
+			&pdata->autosleep_timeout);
+
+	pdata->autosleep = (pdata->autosleep_timeout) ? true : false;
+
+	for_each_child_of_node(np, child) {
+		if (!strcmp(child->name, "stmpe_gpio")) {
+			pdata->blocks |= STMPE_BLOCK_GPIO;
+		} else if (!strcmp(child->name, "stmpe_keypad")) {
+			pdata->blocks |= STMPE_BLOCK_KEYPAD;
+		} else if (!strcmp(child->name, "stmpe_touchscreen")) {
+			pdata->blocks |= STMPE_BLOCK_TOUCHSCREEN;
+		} else if (!strcmp(child->name, "stmpe_adc")) {
+			pdata->blocks |= STMPE_BLOCK_ADC;
+		} else if (!strcmp(child->name, "stmpe_pwm")) {
+			pdata->blocks |= STMPE_BLOCK_PWM;
+		} else if (!strcmp(child->name, "stmpe_rotator")) {
+			pdata->blocks |= STMPE_BLOCK_ROTATOR;
+		}
+	}
+}
+
 /* Called from client specific probe routines */
 int __devinit stmpe_probe(struct stmpe_client_info *ci, int partnum)
 {
 	struct stmpe_platform_data *pdata = dev_get_platdata(ci->dev);
+	struct device_node *np = ci->dev->of_node;
 	struct stmpe *stmpe;
 	int ret;
 
-	if (!pdata)
-		return -EINVAL;
+	if (!pdata) {
+		if (!np)
+			return -EINVAL;
 
-	stmpe = kzalloc(sizeof(struct stmpe), GFP_KERNEL);
+		pdata = devm_kzalloc(ci->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata)
+			return -ENOMEM;
+
+		stmpe_of_probe(pdata, np);
+	}
+
+	stmpe = devm_kzalloc(ci->dev, sizeof(struct stmpe), GFP_KERNEL);
 	if (!stmpe)
 		return -ENOMEM;
 
@@ -1026,11 +1082,12 @@
 		ci->init(stmpe);
 
 	if (pdata->irq_over_gpio) {
-		ret = gpio_request_one(pdata->irq_gpio, GPIOF_DIR_IN, "stmpe");
+		ret = devm_gpio_request_one(ci->dev, pdata->irq_gpio,
+				GPIOF_DIR_IN, "stmpe");
 		if (ret) {
 			dev_err(stmpe->dev, "failed to request IRQ GPIO: %d\n",
 					ret);
-			goto out_free;
+			return ret;
 		}
 
 		stmpe->irq = gpio_to_irq(pdata->irq_gpio);
@@ -1047,51 +1104,40 @@
 			dev_err(stmpe->dev,
 				"%s does not support no-irq mode!\n",
 				stmpe->variant->name);
-			ret = -ENODEV;
-			goto free_gpio;
+			return -ENODEV;
 		}
 		stmpe->variant = stmpe_noirq_variant_info[stmpe->partnum];
+	} else if (pdata->irq_trigger == IRQF_TRIGGER_NONE) {
+		pdata->irq_trigger =
+			irqd_get_trigger_type(irq_get_irq_data(stmpe->irq));
 	}
 
 	ret = stmpe_chip_init(stmpe);
 	if (ret)
-		goto free_gpio;
+		return ret;
 
 	if (stmpe->irq >= 0) {
-		ret = stmpe_irq_init(stmpe);
+		ret = stmpe_irq_init(stmpe, np);
 		if (ret)
-			goto free_gpio;
+			return ret;
 
-		ret = request_threaded_irq(stmpe->irq, NULL, stmpe_irq,
-				pdata->irq_trigger | IRQF_ONESHOT,
+		ret = devm_request_threaded_irq(ci->dev, stmpe->irq, NULL,
+				stmpe_irq, pdata->irq_trigger | IRQF_ONESHOT,
 				"stmpe", stmpe);
 		if (ret) {
 			dev_err(stmpe->dev, "failed to request IRQ: %d\n",
 					ret);
-			goto out_removeirq;
+			return ret;
 		}
 	}
 
 	ret = stmpe_devices_init(stmpe);
-	if (ret) {
-		dev_err(stmpe->dev, "failed to add children\n");
-		goto out_removedevs;
-	}
+	if (!ret)
+		return 0;
 
-	return 0;
-
-out_removedevs:
+	dev_err(stmpe->dev, "failed to add children\n");
 	mfd_remove_devices(stmpe->dev);
-	if (stmpe->irq >= 0)
-		free_irq(stmpe->irq, stmpe);
-out_removeirq:
-	if (stmpe->irq >= 0)
-		stmpe_irq_remove(stmpe);
-free_gpio:
-	if (pdata->irq_over_gpio)
-		gpio_free(pdata->irq_gpio);
-out_free:
-	kfree(stmpe);
+
 	return ret;
 }
 
@@ -1099,16 +1145,6 @@
 {
 	mfd_remove_devices(stmpe->dev);
 
-	if (stmpe->irq >= 0) {
-		free_irq(stmpe->irq, stmpe);
-		stmpe_irq_remove(stmpe);
-	}
-
-	if (stmpe->pdata->irq_over_gpio)
-		gpio_free(stmpe->pdata->irq_gpio);
-
-	kfree(stmpe);
-
 	return 0;
 }
 
diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c
new file mode 100644
index 0000000..8ca3bf0
--- /dev/null
+++ b/drivers/mfd/ti_am335x_tscadc.c
@@ -0,0 +1,274 @@
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/mfd/core.h>
+#include <linux/pm_runtime.h>
+
+#include <linux/mfd/ti_am335x_tscadc.h>
+#include <linux/input/ti_am335x_tsc.h>
+#include <linux/platform_data/ti_am335x_adc.h>
+
+static unsigned int tscadc_readl(struct ti_tscadc_dev *tsadc, unsigned int reg)
+{
+	unsigned int val;
+
+	regmap_read(tsadc->regmap_tscadc, reg, &val);
+	return val;
+}
+
+static void tscadc_writel(struct ti_tscadc_dev *tsadc, unsigned int reg,
+					unsigned int val)
+{
+	regmap_write(tsadc->regmap_tscadc, reg, val);
+}
+
+static const struct regmap_config tscadc_regmap_config = {
+	.name = "ti_tscadc",
+	.reg_bits = 32,
+	.reg_stride = 4,
+	.val_bits = 32,
+};
+
+static void tscadc_idle_config(struct ti_tscadc_dev *config)
+{
+	unsigned int idleconfig;
+
+	idleconfig = STEPCONFIG_YNN | STEPCONFIG_INM_ADCREFM |
+			STEPCONFIG_INP_ADCREFM | STEPCONFIG_YPN;
+
+	tscadc_writel(config, REG_IDLECONFIG, idleconfig);
+}
+
+static	int __devinit ti_tscadc_probe(struct platform_device *pdev)
+{
+	struct ti_tscadc_dev	*tscadc;
+	struct resource		*res;
+	struct clk		*clk;
+	struct mfd_tscadc_board	*pdata = pdev->dev.platform_data;
+	struct mfd_cell		*cell;
+	int			err, ctrl;
+	int			clk_value, clock_rate;
+	int			tsc_wires, adc_channels = 0, total_channels;
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "Could not find platform data\n");
+		return -EINVAL;
+	}
+
+	if (pdata->adc_init)
+		adc_channels = pdata->adc_init->adc_channels;
+
+	tsc_wires = pdata->tsc_init->wires;
+	total_channels = tsc_wires + adc_channels;
+
+	if (total_channels > 8) {
+		dev_err(&pdev->dev, "Number of i/p channels more than 8\n");
+		return -EINVAL;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "no memory resource defined.\n");
+		return -EINVAL;
+	}
+
+	/* Allocate memory for device */
+	tscadc = devm_kzalloc(&pdev->dev,
+			sizeof(struct ti_tscadc_dev), GFP_KERNEL);
+	if (!tscadc) {
+		dev_err(&pdev->dev, "failed to allocate memory.\n");
+		return -ENOMEM;
+	}
+	tscadc->dev = &pdev->dev;
+
+	err = platform_get_irq(pdev, 0);
+	if (err < 0) {
+		dev_err(&pdev->dev, "no irq ID is specified.\n");
+		goto ret;
+	} else
+		tscadc->irq = err;
+
+	res = devm_request_mem_region(&pdev->dev,
+			res->start, resource_size(res), pdev->name);
+	if (!res) {
+		dev_err(&pdev->dev, "failed to reserve registers.\n");
+		return -EBUSY;
+	}
+
+	tscadc->tscadc_base = devm_ioremap(&pdev->dev,
+			res->start, resource_size(res));
+	if (!tscadc->tscadc_base) {
+		dev_err(&pdev->dev, "failed to map registers.\n");
+		return -ENOMEM;
+	}
+
+	tscadc->regmap_tscadc = devm_regmap_init_mmio(&pdev->dev,
+			tscadc->tscadc_base, &tscadc_regmap_config);
+	if (IS_ERR(tscadc->regmap_tscadc)) {
+		dev_err(&pdev->dev, "regmap init failed\n");
+		err = PTR_ERR(tscadc->regmap_tscadc);
+		goto ret;
+	}
+
+	pm_runtime_enable(&pdev->dev);
+	pm_runtime_get_sync(&pdev->dev);
+
+	/*
+	 * The TSC_ADC_Subsystem has 2 clock domains
+	 * OCP_CLK and ADC_CLK.
+	 * The ADC clock is expected to run at target of 3MHz,
+	 * and expected to capture 12-bit data at a rate of 200 KSPS.
+	 * The TSC_ADC_SS controller design assumes the OCP clock is
+	 * at least 6x faster than the ADC clock.
+	 */
+	clk = clk_get(&pdev->dev, "adc_tsc_fck");
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed to get TSC fck\n");
+		err = PTR_ERR(clk);
+		goto err_disable_clk;
+	}
+	clock_rate = clk_get_rate(clk);
+	clk_put(clk);
+	clk_value = clock_rate / ADC_CLK;
+	if (clk_value < MAX_CLK_DIV) {
+		dev_err(&pdev->dev, "clock input less than min clock requirement\n");
+		err = -EINVAL;
+		goto err_disable_clk;
+	}
+	/* TSCADC_CLKDIV needs to be configured to the value minus 1 */
+	clk_value = clk_value - 1;
+	tscadc_writel(tscadc, REG_CLKDIV, clk_value);
+
+	/* Set the control register bits */
+	ctrl = CNTRLREG_STEPCONFIGWRT |
+			CNTRLREG_TSCENB |
+			CNTRLREG_STEPID |
+			CNTRLREG_4WIRE;
+	tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+	/* Set register bits for Idle Config Mode */
+	tscadc_idle_config(tscadc);
+
+	/* Enable the TSC module enable bit */
+	ctrl = tscadc_readl(tscadc, REG_CTRL);
+	ctrl |= CNTRLREG_TSCSSENB;
+	tscadc_writel(tscadc, REG_CTRL, ctrl);
+
+	/* TSC Cell */
+	cell = &tscadc->cells[TSC_CELL];
+	cell->name = "tsc";
+	cell->platform_data = tscadc;
+	cell->pdata_size = sizeof(*tscadc);
+
+	/* ADC Cell */
+	cell = &tscadc->cells[ADC_CELL];
+	cell->name = "tiadc";
+	cell->platform_data = tscadc;
+	cell->pdata_size = sizeof(*tscadc);
+
+	err = mfd_add_devices(&pdev->dev, pdev->id, tscadc->cells,
+			TSCADC_CELLS, NULL, 0, NULL);
+	if (err < 0)
+		goto err_disable_clk;
+
+	device_init_wakeup(&pdev->dev, true);
+	platform_set_drvdata(pdev, tscadc);
+
+	return 0;
+
+err_disable_clk:
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+ret:
+	return err;
+}
+
+static int __devexit ti_tscadc_remove(struct platform_device *pdev)
+{
+	struct ti_tscadc_dev	*tscadc = platform_get_drvdata(pdev);
+
+	tscadc_writel(tscadc, REG_SE, 0x00);
+
+	pm_runtime_put_sync(&pdev->dev);
+	pm_runtime_disable(&pdev->dev);
+
+	mfd_remove_devices(tscadc->dev);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int tscadc_suspend(struct device *dev)
+{
+	struct ti_tscadc_dev	*tscadc_dev = dev_get_drvdata(dev);
+
+	tscadc_writel(tscadc_dev, REG_SE, 0x00);
+	pm_runtime_put_sync(dev);
+
+	return 0;
+}
+
+static int tscadc_resume(struct device *dev)
+{
+	struct ti_tscadc_dev	*tscadc_dev = dev_get_drvdata(dev);
+	unsigned int restore, ctrl;
+
+	pm_runtime_get_sync(dev);
+
+	/* context restore */
+	ctrl = CNTRLREG_STEPCONFIGWRT | CNTRLREG_TSCENB |
+			CNTRLREG_STEPID | CNTRLREG_4WIRE;
+	tscadc_writel(tscadc_dev, REG_CTRL, ctrl);
+	tscadc_idle_config(tscadc_dev);
+	tscadc_writel(tscadc_dev, REG_SE, STPENB_STEPENB);
+	restore = tscadc_readl(tscadc_dev, REG_CTRL);
+	tscadc_writel(tscadc_dev, REG_CTRL,
+			(restore | CNTRLREG_TSCSSENB));
+
+	return 0;
+}
+
+static const struct dev_pm_ops tscadc_pm_ops = {
+	.suspend = tscadc_suspend,
+	.resume = tscadc_resume,
+};
+#define TSCADC_PM_OPS (&tscadc_pm_ops)
+#else
+#define TSCADC_PM_OPS NULL
+#endif
+
+static struct platform_driver ti_tscadc_driver = {
+	.driver = {
+		.name   = "ti_tscadc",
+		.owner	= THIS_MODULE,
+		.pm	= TSCADC_PM_OPS,
+	},
+	.probe	= ti_tscadc_probe,
+	.remove	= __devexit_p(ti_tscadc_remove),
+
+};
+
+module_platform_driver(ti_tscadc_driver);
+
+MODULE_DESCRIPTION("TI touchscreen / ADC MFD controller driver");
+MODULE_AUTHOR("Rachna Patil <rachna@ti.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/tps6507x.c b/drivers/mfd/tps6507x.c
index 1b20349..409afa2 100644
--- a/drivers/mfd/tps6507x.c
+++ b/drivers/mfd/tps6507x.c
@@ -86,9 +86,9 @@
 			    const struct i2c_device_id *id)
 {
 	struct tps6507x_dev *tps6507x;
-	int ret = 0;
 
-	tps6507x = kzalloc(sizeof(struct tps6507x_dev), GFP_KERNEL);
+	tps6507x = devm_kzalloc(&i2c->dev, sizeof(struct tps6507x_dev),
+				GFP_KERNEL);
 	if (tps6507x == NULL)
 		return -ENOMEM;
 
@@ -98,19 +98,8 @@
 	tps6507x->read_dev = tps6507x_i2c_read_device;
 	tps6507x->write_dev = tps6507x_i2c_write_device;
 
-	ret = mfd_add_devices(tps6507x->dev, -1,
-			      tps6507x_devs, ARRAY_SIZE(tps6507x_devs),
-			      NULL, 0, NULL);
-
-	if (ret < 0)
-		goto err;
-
-	return ret;
-
-err:
-	mfd_remove_devices(tps6507x->dev);
-	kfree(tps6507x);
-	return ret;
+	return mfd_add_devices(tps6507x->dev, -1, tps6507x_devs,
+			       ARRAY_SIZE(tps6507x_devs), NULL, 0, NULL);
 }
 
 static int tps6507x_i2c_remove(struct i2c_client *i2c)
@@ -118,8 +107,6 @@
 	struct tps6507x_dev *tps6507x = i2c_get_clientdata(i2c);
 
 	mfd_remove_devices(tps6507x->dev);
-	kfree(tps6507x);
-
 	return 0;
 }
 
diff --git a/drivers/mfd/tps65090.c b/drivers/mfd/tps65090.c
index 382a857..8d12a8e 100644
--- a/drivers/mfd/tps65090.c
+++ b/drivers/mfd/tps65090.c
@@ -25,7 +25,6 @@
 #include <linux/i2c.h>
 #include <linux/mfd/core.h>
 #include <linux/mfd/tps65090.h>
-#include <linux/regmap.h>
 #include <linux/err.h>
 
 #define NUM_INT_REG 2
@@ -39,204 +38,102 @@
 #define TPS65090_INT_MSK	0x2
 #define TPS65090_INT_MSK2	0x3
 
-struct tps65090_irq_data {
-	u8		mask_reg;
-	u8		mask_pos;
-};
-
-#define TPS65090_IRQ(_reg, _mask_pos)		\
-	{					\
-		.mask_reg	= (_reg),	\
-		.mask_pos	= (_mask_pos),	\
-	}
-
-static const struct tps65090_irq_data tps65090_irqs[] = {
-	[0]		= TPS65090_IRQ(0, 0),
-	[1]		= TPS65090_IRQ(0, 1),
-	[2]		= TPS65090_IRQ(0, 2),
-	[3]		= TPS65090_IRQ(0, 3),
-	[4]		= TPS65090_IRQ(0, 4),
-	[5]		= TPS65090_IRQ(0, 5),
-	[6]		= TPS65090_IRQ(0, 6),
-	[7]		= TPS65090_IRQ(0, 7),
-	[8]		= TPS65090_IRQ(1, 0),
-	[9]		= TPS65090_IRQ(1, 1),
-	[10]		= TPS65090_IRQ(1, 2),
-	[11]		= TPS65090_IRQ(1, 3),
-	[12]		= TPS65090_IRQ(1, 4),
-	[13]		= TPS65090_IRQ(1, 5),
-	[14]		= TPS65090_IRQ(1, 6),
-	[15]		= TPS65090_IRQ(1, 7),
-};
+#define TPS65090_INT1_MASK_VAC_STATUS_CHANGE		1
+#define TPS65090_INT1_MASK_VSYS_STATUS_CHANGE		2
+#define TPS65090_INT1_MASK_BAT_STATUS_CHANGE		3
+#define TPS65090_INT1_MASK_CHARGING_STATUS_CHANGE	4
+#define TPS65090_INT1_MASK_CHARGING_COMPLETE		5
+#define TPS65090_INT1_MASK_OVERLOAD_DCDC1		6
+#define TPS65090_INT1_MASK_OVERLOAD_DCDC2		7
+#define TPS65090_INT2_MASK_OVERLOAD_DCDC3		0
+#define TPS65090_INT2_MASK_OVERLOAD_FET1		1
+#define TPS65090_INT2_MASK_OVERLOAD_FET2		2
+#define TPS65090_INT2_MASK_OVERLOAD_FET3		3
+#define TPS65090_INT2_MASK_OVERLOAD_FET4		4
+#define TPS65090_INT2_MASK_OVERLOAD_FET5		5
+#define TPS65090_INT2_MASK_OVERLOAD_FET6		6
+#define TPS65090_INT2_MASK_OVERLOAD_FET7		7
 
 static struct mfd_cell tps65090s[] = {
 	{
 		.name = "tps65090-pmic",
 	},
 	{
-		.name = "tps65090-regulator",
+		.name = "tps65090-charger",
 	},
 };
 
-int tps65090_write(struct device *dev, int reg, uint8_t val)
-{
-	struct tps65090 *tps = dev_get_drvdata(dev);
-	return regmap_write(tps->rmap, reg, val);
-}
-EXPORT_SYMBOL_GPL(tps65090_write);
+static const struct regmap_irq tps65090_irqs[] = {
+	/* INT1 IRQs*/
+	[TPS65090_IRQ_VAC_STATUS_CHANGE] = {
+			.mask = TPS65090_INT1_MASK_VAC_STATUS_CHANGE,
+	},
+	[TPS65090_IRQ_VSYS_STATUS_CHANGE] = {
+			.mask = TPS65090_INT1_MASK_VSYS_STATUS_CHANGE,
+	},
+	[TPS65090_IRQ_BAT_STATUS_CHANGE] = {
+			.mask = TPS65090_INT1_MASK_BAT_STATUS_CHANGE,
+	},
+	[TPS65090_IRQ_CHARGING_STATUS_CHANGE] = {
+			.mask = TPS65090_INT1_MASK_CHARGING_STATUS_CHANGE,
+	},
+	[TPS65090_IRQ_CHARGING_COMPLETE] = {
+			.mask = TPS65090_INT1_MASK_CHARGING_COMPLETE,
+	},
+	[TPS65090_IRQ_OVERLOAD_DCDC1] = {
+			.mask = TPS65090_INT1_MASK_OVERLOAD_DCDC1,
+	},
+	[TPS65090_IRQ_OVERLOAD_DCDC2] = {
+			.mask = TPS65090_INT1_MASK_OVERLOAD_DCDC2,
+	},
+	/* INT2 IRQs*/
+	[TPS65090_IRQ_OVERLOAD_DCDC3] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_DCDC3,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET1] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET1,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET2] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET2,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET3] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET3,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET4] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET4,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET5] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET5,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET6] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET6,
+	},
+	[TPS65090_IRQ_OVERLOAD_FET7] = {
+			.reg_offset = 1,
+			.mask = TPS65090_INT2_MASK_OVERLOAD_FET7,
+	},
+};
 
-int tps65090_read(struct device *dev, int reg, uint8_t *val)
-{
-	struct tps65090 *tps = dev_get_drvdata(dev);
-	unsigned int temp_val;
-	int ret;
-	ret = regmap_read(tps->rmap, reg, &temp_val);
-	if (!ret)
-		*val = temp_val;
-	return ret;
-}
-EXPORT_SYMBOL_GPL(tps65090_read);
-
-int tps65090_set_bits(struct device *dev, int reg, uint8_t bit_num)
-{
-	struct tps65090 *tps = dev_get_drvdata(dev);
-	return regmap_update_bits(tps->rmap, reg, BIT(bit_num), ~0u);
-}
-EXPORT_SYMBOL_GPL(tps65090_set_bits);
-
-int tps65090_clr_bits(struct device *dev, int reg, uint8_t bit_num)
-{
-	struct tps65090 *tps = dev_get_drvdata(dev);
-	return regmap_update_bits(tps->rmap, reg, BIT(bit_num), 0u);
-}
-EXPORT_SYMBOL_GPL(tps65090_clr_bits);
-
-static void tps65090_irq_lock(struct irq_data *data)
-{
-	struct tps65090 *tps65090 = irq_data_get_irq_chip_data(data);
-
-	mutex_lock(&tps65090->irq_lock);
-}
-
-static void tps65090_irq_mask(struct irq_data *irq_data)
-{
-	struct tps65090 *tps65090 = irq_data_get_irq_chip_data(irq_data);
-	unsigned int __irq = irq_data->hwirq;
-	const struct tps65090_irq_data *data = &tps65090_irqs[__irq];
-
-	tps65090_set_bits(tps65090->dev, (TPS65090_INT_MSK + data->mask_reg),
-		data->mask_pos);
-}
-
-static void tps65090_irq_unmask(struct irq_data *irq_data)
-{
-	struct tps65090 *tps65090 = irq_data_get_irq_chip_data(irq_data);
-	unsigned int __irq = irq_data->irq - tps65090->irq_base;
-	const struct tps65090_irq_data *data = &tps65090_irqs[__irq];
-
-	tps65090_clr_bits(tps65090->dev, (TPS65090_INT_MSK + data->mask_reg),
-		data->mask_pos);
-}
-
-static void tps65090_irq_sync_unlock(struct irq_data *data)
-{
-	struct tps65090 *tps65090 = irq_data_get_irq_chip_data(data);
-
-	mutex_unlock(&tps65090->irq_lock);
-}
-
-static irqreturn_t tps65090_irq(int irq, void *data)
-{
-	struct tps65090 *tps65090 = data;
-	int ret = 0;
-	u8 status, mask;
-	unsigned long int acks = 0;
-	int i;
-
-	for (i = 0; i < NUM_INT_REG; i++) {
-		ret = tps65090_read(tps65090->dev, TPS65090_INT_MSK + i, &mask);
-		if (ret < 0) {
-			dev_err(tps65090->dev,
-				"failed to read mask reg [addr:%d]\n",
-				TPS65090_INT_MSK + i);
-			return IRQ_NONE;
-		}
-		ret = tps65090_read(tps65090->dev, TPS65090_INT_STS + i,
-			&status);
-		if (ret < 0) {
-			dev_err(tps65090->dev,
-				"failed to read status reg [addr:%d]\n",
-				 TPS65090_INT_STS + i);
-			return IRQ_NONE;
-		}
-		if (status) {
-			/* Ack only those interrupts which are not masked */
-			status &= (~mask);
-			ret = tps65090_write(tps65090->dev,
-					TPS65090_INT_STS + i, status);
-			if (ret < 0) {
-				dev_err(tps65090->dev,
-					"failed to write interrupt status\n");
-				return IRQ_NONE;
-			}
-			acks |= (status << (i * 8));
-		}
-	}
-
-	for_each_set_bit(i, &acks, ARRAY_SIZE(tps65090_irqs))
-		handle_nested_irq(tps65090->irq_base + i);
-	return acks ? IRQ_HANDLED : IRQ_NONE;
-}
-
-static int tps65090_irq_init(struct tps65090 *tps65090, int irq,
-	int irq_base)
-{
-	int i, ret;
-
-	if (!irq_base) {
-		dev_err(tps65090->dev, "IRQ base not set\n");
-		return -EINVAL;
-	}
-
-	mutex_init(&tps65090->irq_lock);
-
-	for (i = 0; i < NUM_INT_REG; i++)
-		tps65090_write(tps65090->dev, TPS65090_INT_MSK + i, 0xFF);
-
-	for (i = 0; i < NUM_INT_REG; i++)
-		tps65090_write(tps65090->dev, TPS65090_INT_STS + i, 0xff);
-
-	tps65090->irq_base = irq_base;
-	tps65090->irq_chip.name = "tps65090";
-	tps65090->irq_chip.irq_mask = tps65090_irq_mask;
-	tps65090->irq_chip.irq_unmask = tps65090_irq_unmask;
-	tps65090->irq_chip.irq_bus_lock = tps65090_irq_lock;
-	tps65090->irq_chip.irq_bus_sync_unlock = tps65090_irq_sync_unlock;
-
-	for (i = 0; i < ARRAY_SIZE(tps65090_irqs); i++) {
-		int __irq = i + tps65090->irq_base;
-		irq_set_chip_data(__irq, tps65090);
-		irq_set_chip_and_handler(__irq, &tps65090->irq_chip,
-					 handle_simple_irq);
-		irq_set_nested_thread(__irq, 1);
-#ifdef CONFIG_ARM
-		set_irq_flags(__irq, IRQF_VALID);
-#endif
-	}
-
-	ret = request_threaded_irq(irq, NULL, tps65090_irq, IRQF_ONESHOT,
-				"tps65090", tps65090);
-	if (!ret) {
-		device_init_wakeup(tps65090->dev, 1);
-		enable_irq_wake(irq);
-	}
-
-	return ret;
-}
+static struct regmap_irq_chip tps65090_irq_chip = {
+	.name = "tps65090",
+	.irqs = tps65090_irqs,
+	.num_irqs = ARRAY_SIZE(tps65090_irqs),
+	.num_regs = NUM_INT_REG,
+	.status_base = TPS65090_INT_STS,
+	.mask_base = TPS65090_INT_MSK,
+	.mask_invert = true,
+};
 
 static bool is_volatile_reg(struct device *dev, unsigned int reg)
 {
-	if (reg == TPS65090_INT_STS)
+	if ((reg == TPS65090_INT_STS) || (reg == TPS65090_INT_STS2))
 		return true;
 	else
 		return false;
@@ -263,36 +160,36 @@
 		return -EINVAL;
 	}
 
-	tps65090 = devm_kzalloc(&client->dev, sizeof(struct tps65090),
-		GFP_KERNEL);
-	if (tps65090 == NULL)
+	tps65090 = devm_kzalloc(&client->dev, sizeof(*tps65090), GFP_KERNEL);
+	if (!tps65090) {
+		dev_err(&client->dev, "mem alloc for tps65090 failed\n");
 		return -ENOMEM;
+	}
 
-	tps65090->client = client;
 	tps65090->dev = &client->dev;
 	i2c_set_clientdata(client, tps65090);
 
-	mutex_init(&tps65090->lock);
-
-	if (client->irq) {
-		ret = tps65090_irq_init(tps65090, client->irq, pdata->irq_base);
-		if (ret) {
-			dev_err(&client->dev, "IRQ init failed with err: %d\n",
-				ret);
-			goto err_exit;
-		}
-	}
-
-	tps65090->rmap = devm_regmap_init_i2c(tps65090->client,
-					      &tps65090_regmap_config);
+	tps65090->rmap = devm_regmap_init_i2c(client, &tps65090_regmap_config);
 	if (IS_ERR(tps65090->rmap)) {
 		ret = PTR_ERR(tps65090->rmap);
 		dev_err(&client->dev, "regmap_init failed with err: %d\n", ret);
-		goto err_irq_exit;
+		return ret;
+	}
+
+	if (client->irq) {
+		ret = regmap_add_irq_chip(tps65090->rmap, client->irq,
+			IRQF_ONESHOT | IRQF_TRIGGER_LOW, pdata->irq_base,
+			&tps65090_irq_chip, &tps65090->irq_data);
+			if (ret) {
+				dev_err(&client->dev,
+					"IRQ init failed with err: %d\n", ret);
+			return ret;
+		}
 	}
 
 	ret = mfd_add_devices(tps65090->dev, -1, tps65090s,
-			      ARRAY_SIZE(tps65090s), NULL, 0, NULL);
+		ARRAY_SIZE(tps65090s), NULL,
+		regmap_irq_chip_get_base(tps65090->irq_data), NULL);
 	if (ret) {
 		dev_err(&client->dev, "add mfd devices failed with err: %d\n",
 			ret);
@@ -303,8 +200,7 @@
 
 err_irq_exit:
 	if (client->irq)
-		free_irq(client->irq, tps65090);
-err_exit:
+		regmap_del_irq_chip(client->irq, tps65090->irq_data);
 	return ret;
 }
 
@@ -314,7 +210,7 @@
 
 	mfd_remove_devices(tps65090->dev);
 	if (client->irq)
-		free_irq(client->irq, tps65090);
+		regmap_del_irq_chip(client->irq, tps65090->irq_data);
 
 	return 0;
 }
diff --git a/drivers/mfd/tps65217.c b/drivers/mfd/tps65217.c
index e14e252..b8f4864 100644
--- a/drivers/mfd/tps65217.c
+++ b/drivers/mfd/tps65217.c
@@ -160,6 +160,7 @@
 	unsigned int version;
 	unsigned int chip_id = ids->driver_data;
 	const struct of_device_id *match;
+	bool status_off = false;
 	int ret;
 
 	if (client->dev.of_node) {
@@ -170,6 +171,8 @@
 			return -EINVAL;
 		}
 		chip_id = (unsigned int)match->data;
+		status_off = of_property_read_bool(client->dev.of_node,
+					"ti,pmic-shutdown-controller");
 	}
 
 	if (!chip_id) {
@@ -207,6 +210,15 @@
 		return ret;
 	}
 
+	/* Set the PMIC to shutdown on PWR_EN toggle */
+	if (status_off) {
+		ret = tps65217_set_bits(tps, TPS65217_REG_STATUS,
+				TPS65217_STATUS_OFF, TPS65217_STATUS_OFF,
+				TPS65217_PROTECT_NONE);
+		if (ret)
+			dev_warn(tps->dev, "unable to set the status OFF\n");
+	}
+
 	dev_info(tps->dev, "TPS65217 ID %#x version 1.%d\n",
 			(version & TPS65217_CHIPID_CHIP_MASK) >> 4,
 			version & TPS65217_CHIPID_REV_MASK);
diff --git a/drivers/mfd/tps6586x.c b/drivers/mfd/tps6586x.c
index 87ba7ad..721b918 100644
--- a/drivers/mfd/tps6586x.c
+++ b/drivers/mfd/tps6586x.c
@@ -17,12 +17,14 @@
 
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqdomain.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/slab.h>
 #include <linux/err.h>
 #include <linux/i2c.h>
+#include <linux/platform_device.h>
 #include <linux/regmap.h>
 
 #include <linux/mfd/core.h>
@@ -92,6 +94,14 @@
 	[TPS6586X_INT_RTC_ALM2] = TPS6586X_IRQ(TPS6586X_INT_MASK4, 1 << 1),
 };
 
+static struct resource tps6586x_rtc_resources[] = {
+	{
+		.start  = TPS6586X_INT_RTC_ALM1,
+		.end	= TPS6586X_INT_RTC_ALM1,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
 static struct mfd_cell tps6586x_cell[] = {
 	{
 		.name = "tps6586x-gpio",
@@ -101,6 +111,8 @@
 	},
 	{
 		.name = "tps6586x-rtc",
+		.num_resources = ARRAY_SIZE(tps6586x_rtc_resources),
+		.resources = &tps6586x_rtc_resources[0],
 	},
 	{
 		.name = "tps6586x-onkey",
@@ -117,6 +129,7 @@
 	int			irq_base;
 	u32			irq_en;
 	u8			mask_reg[5];
+	struct irq_domain	*irq_domain;
 };
 
 static inline struct tps6586x *dev_to_tps6586x(struct device *dev)
@@ -185,6 +198,14 @@
 }
 EXPORT_SYMBOL_GPL(tps6586x_update);
 
+int tps6586x_irq_get_virq(struct device *dev, int irq)
+{
+	struct tps6586x *tps6586x = dev_to_tps6586x(dev);
+
+	return irq_create_mapping(tps6586x->irq_domain, irq);
+}
+EXPORT_SYMBOL_GPL(tps6586x_irq_get_virq);
+
 static int __remove_subdev(struct device *dev, void *unused)
 {
 	platform_device_unregister(to_platform_device(dev));
@@ -206,7 +227,7 @@
 static void tps6586x_irq_enable(struct irq_data *irq_data)
 {
 	struct tps6586x *tps6586x = irq_data_get_irq_chip_data(irq_data);
-	unsigned int __irq = irq_data->irq - tps6586x->irq_base;
+	unsigned int __irq = irq_data->hwirq;
 	const struct tps6586x_irq_data *data = &tps6586x_irqs[__irq];
 
 	tps6586x->mask_reg[data->mask_reg] &= ~data->mask_mask;
@@ -217,7 +238,7 @@
 {
 	struct tps6586x *tps6586x = irq_data_get_irq_chip_data(irq_data);
 
-	unsigned int __irq = irq_data->irq - tps6586x->irq_base;
+	unsigned int __irq = irq_data->hwirq;
 	const struct tps6586x_irq_data *data = &tps6586x_irqs[__irq];
 
 	tps6586x->mask_reg[data->mask_reg] |= data->mask_mask;
@@ -240,6 +261,39 @@
 	mutex_unlock(&tps6586x->irq_lock);
 }
 
+static struct irq_chip tps6586x_irq_chip = {
+	.name = "tps6586x",
+	.irq_bus_lock = tps6586x_irq_lock,
+	.irq_bus_sync_unlock = tps6586x_irq_sync_unlock,
+	.irq_disable = tps6586x_irq_disable,
+	.irq_enable = tps6586x_irq_enable,
+};
+
+static int tps6586x_irq_map(struct irq_domain *h, unsigned int virq,
+				irq_hw_number_t hw)
+{
+	struct tps6586x *tps6586x = h->host_data;
+
+	irq_set_chip_data(virq, tps6586x);
+	irq_set_chip_and_handler(virq, &tps6586x_irq_chip, handle_simple_irq);
+	irq_set_nested_thread(virq, 1);
+
+	/* ARM needs us to explicitly flag the IRQ as valid
+	 * and will set them noprobe when we do so. */
+#ifdef CONFIG_ARM
+	set_irq_flags(virq, IRQF_VALID);
+#else
+	irq_set_noprobe(virq);
+#endif
+
+	return 0;
+}
+
+static struct irq_domain_ops tps6586x_domain_ops = {
+	.map    = tps6586x_irq_map,
+	.xlate  = irq_domain_xlate_twocell,
+};
+
 static irqreturn_t tps6586x_irq(int irq, void *data)
 {
 	struct tps6586x *tps6586x = data;
@@ -260,7 +314,8 @@
 		int i = __ffs(acks);
 
 		if (tps6586x->irq_en & (1 << i))
-			handle_nested_irq(tps6586x->irq_base + i);
+			handle_nested_irq(
+				irq_find_mapping(tps6586x->irq_domain, i));
 
 		acks &= ~(1 << i);
 	}
@@ -273,11 +328,8 @@
 {
 	int i, ret;
 	u8 tmp[4];
-
-	if (!irq_base) {
-		dev_warn(tps6586x->dev, "No interrupt support on IRQ base\n");
-		return -EINVAL;
-	}
+	int new_irq_base;
+	int irq_num = ARRAY_SIZE(tps6586x_irqs);
 
 	mutex_init(&tps6586x->irq_lock);
 	for (i = 0; i < 5; i++) {
@@ -287,25 +339,24 @@
 
 	tps6586x_reads(tps6586x->dev, TPS6586X_INT_ACK1, sizeof(tmp), tmp);
 
-	tps6586x->irq_base = irq_base;
-
-	tps6586x->irq_chip.name = "tps6586x";
-	tps6586x->irq_chip.irq_enable = tps6586x_irq_enable;
-	tps6586x->irq_chip.irq_disable = tps6586x_irq_disable;
-	tps6586x->irq_chip.irq_bus_lock = tps6586x_irq_lock;
-	tps6586x->irq_chip.irq_bus_sync_unlock = tps6586x_irq_sync_unlock;
-
-	for (i = 0; i < ARRAY_SIZE(tps6586x_irqs); i++) {
-		int __irq = i + tps6586x->irq_base;
-		irq_set_chip_data(__irq, tps6586x);
-		irq_set_chip_and_handler(__irq, &tps6586x->irq_chip,
-					 handle_simple_irq);
-		irq_set_nested_thread(__irq, 1);
-#ifdef CONFIG_ARM
-		set_irq_flags(__irq, IRQF_VALID);
-#endif
+	if  (irq_base > 0) {
+		new_irq_base = irq_alloc_descs(irq_base, 0, irq_num, -1);
+		if (new_irq_base < 0) {
+			dev_err(tps6586x->dev,
+				"Failed to alloc IRQs: %d\n", new_irq_base);
+			return new_irq_base;
+		}
+	} else {
+		new_irq_base = 0;
 	}
 
+	tps6586x->irq_domain = irq_domain_add_simple(tps6586x->dev->of_node,
+				irq_num, new_irq_base, &tps6586x_domain_ops,
+				tps6586x);
+	if (!tps6586x->irq_domain) {
+		dev_err(tps6586x->dev, "Failed to create IRQ domain\n");
+		return -ENOMEM;
+	}
 	ret = request_threaded_irq(irq, NULL, tps6586x_irq, IRQF_ONESHOT,
 				   "tps6586x", tps6586x);
 
@@ -461,7 +512,7 @@
 
 	ret = mfd_add_devices(tps6586x->dev, -1,
 			      tps6586x_cell, ARRAY_SIZE(tps6586x_cell),
-			      NULL, 0, NULL);
+			      NULL, 0, tps6586x->irq_domain);
 	if (ret < 0) {
 		dev_err(&client->dev, "mfd_add_devices failed: %d\n", ret);
 		goto err_mfd_add;
diff --git a/drivers/mfd/tps65910-irq.c b/drivers/mfd/tps65910-irq.c
deleted file mode 100644
index 09aab3e4..0000000
--- a/drivers/mfd/tps65910-irq.c
+++ /dev/null
@@ -1,260 +0,0 @@
-/*
- * tps65910-irq.c  --  TI TPS6591x
- *
- * Copyright 2010 Texas Instruments Inc.
- *
- * Author: Graeme Gregory <gg@slimlogic.co.uk>
- * Author: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under  the terms of the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the License, or (at your
- *  option) any later version.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/bug.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/gpio.h>
-#include <linux/mfd/tps65910.h>
-
-/*
- * This is a threaded IRQ handler so can access I2C/SPI.  Since all
- * interrupts are clear on read the IRQ line will be reasserted and
- * the physical IRQ will be handled again if another interrupt is
- * asserted while we run - in the normal course of events this is a
- * rare occurrence so we save I2C/SPI reads.  We're also assuming that
- * it's rare to get lots of interrupts firing simultaneously so try to
- * minimise I/O.
- */
-static irqreturn_t tps65910_irq(int irq, void *irq_data)
-{
-	struct tps65910 *tps65910 = irq_data;
-	unsigned int reg;
-	u32 irq_sts;
-	u32 irq_mask;
-	int i;
-
-	tps65910_reg_read(tps65910, TPS65910_INT_STS, &reg);
-	irq_sts = reg;
-	tps65910_reg_read(tps65910, TPS65910_INT_STS2, &reg);
-	irq_sts |= reg << 8;
-	switch (tps65910_chip_id(tps65910)) {
-	case TPS65911:
-		tps65910_reg_read(tps65910, TPS65910_INT_STS3, &reg);
-		irq_sts |= reg << 16;
-	}
-
-	tps65910_reg_read(tps65910, TPS65910_INT_MSK, &reg);
-	irq_mask = reg;
-	tps65910_reg_read(tps65910, TPS65910_INT_MSK2, &reg);
-	irq_mask |= reg << 8;
-	switch (tps65910_chip_id(tps65910)) {
-	case TPS65911:
-		tps65910_reg_read(tps65910, TPS65910_INT_MSK3, &reg);
-		irq_mask |= reg << 16;
-	}
-
-	irq_sts &= ~irq_mask;
-
-	if (!irq_sts)
-		return IRQ_NONE;
-
-	for (i = 0; i < tps65910->irq_num; i++) {
-
-		if (!(irq_sts & (1 << i)))
-			continue;
-
-		handle_nested_irq(irq_find_mapping(tps65910->domain, i));
-	}
-
-	/* Write the STS register back to clear IRQs we handled */
-	reg = irq_sts & 0xFF;
-	irq_sts >>= 8;
-	tps65910_reg_write(tps65910, TPS65910_INT_STS, reg);
-	reg = irq_sts & 0xFF;
-	tps65910_reg_write(tps65910, TPS65910_INT_STS2, reg);
-	switch (tps65910_chip_id(tps65910)) {
-	case TPS65911:
-		reg = irq_sts >> 8;
-		tps65910_reg_write(tps65910, TPS65910_INT_STS3, reg);
-	}
-
-	return IRQ_HANDLED;
-}
-
-static void tps65910_irq_lock(struct irq_data *data)
-{
-	struct tps65910 *tps65910 = irq_data_get_irq_chip_data(data);
-
-	mutex_lock(&tps65910->irq_lock);
-}
-
-static void tps65910_irq_sync_unlock(struct irq_data *data)
-{
-	struct tps65910 *tps65910 = irq_data_get_irq_chip_data(data);
-	u32 reg_mask;
-	unsigned int reg;
-
-	tps65910_reg_read(tps65910, TPS65910_INT_MSK, &reg);
-	reg_mask = reg;
-	tps65910_reg_read(tps65910, TPS65910_INT_MSK2, &reg);
-	reg_mask |= reg << 8;
-	switch (tps65910_chip_id(tps65910)) {
-	case TPS65911:
-		tps65910_reg_read(tps65910, TPS65910_INT_MSK3, &reg);
-		reg_mask |= reg << 16;
-	}
-
-	if (tps65910->irq_mask != reg_mask) {
-		reg = tps65910->irq_mask & 0xFF;
-		tps65910_reg_write(tps65910, TPS65910_INT_MSK, reg);
-		reg = tps65910->irq_mask >> 8 & 0xFF;
-		tps65910_reg_write(tps65910, TPS65910_INT_MSK2, reg);
-		switch (tps65910_chip_id(tps65910)) {
-		case TPS65911:
-			reg = tps65910->irq_mask >> 16;
-			tps65910_reg_write(tps65910, TPS65910_INT_MSK3, reg);
-		}
-	}
-	mutex_unlock(&tps65910->irq_lock);
-}
-
-static void tps65910_irq_enable(struct irq_data *data)
-{
-	struct tps65910 *tps65910 = irq_data_get_irq_chip_data(data);
-
-	tps65910->irq_mask &= ~(1 << data->hwirq);
-}
-
-static void tps65910_irq_disable(struct irq_data *data)
-{
-	struct tps65910 *tps65910 = irq_data_get_irq_chip_data(data);
-
-	tps65910->irq_mask |= (1 << data->hwirq);
-}
-
-#ifdef CONFIG_PM_SLEEP
-static int tps65910_irq_set_wake(struct irq_data *data, unsigned int enable)
-{
-	struct tps65910 *tps65910 = irq_data_get_irq_chip_data(data);
-	return irq_set_irq_wake(tps65910->chip_irq, enable);
-}
-#else
-#define tps65910_irq_set_wake NULL
-#endif
-
-static struct irq_chip tps65910_irq_chip = {
-	.name = "tps65910",
-	.irq_bus_lock = tps65910_irq_lock,
-	.irq_bus_sync_unlock = tps65910_irq_sync_unlock,
-	.irq_disable = tps65910_irq_disable,
-	.irq_enable = tps65910_irq_enable,
-	.irq_set_wake = tps65910_irq_set_wake,
-};
-
-static int tps65910_irq_map(struct irq_domain *h, unsigned int virq,
-				irq_hw_number_t hw)
-{
-	struct tps65910 *tps65910 = h->host_data;
-
-	irq_set_chip_data(virq, tps65910);
-	irq_set_chip_and_handler(virq, &tps65910_irq_chip, handle_edge_irq);
-	irq_set_nested_thread(virq, 1);
-
-	/* ARM needs us to explicitly flag the IRQ as valid
-	 * and will set them noprobe when we do so. */
-#ifdef CONFIG_ARM
-	set_irq_flags(virq, IRQF_VALID);
-#else
-	irq_set_noprobe(virq);
-#endif
-
-	return 0;
-}
-
-static struct irq_domain_ops tps65910_domain_ops = {
-	.map	= tps65910_irq_map,
-	.xlate	= irq_domain_xlate_twocell,
-};
-
-int tps65910_irq_init(struct tps65910 *tps65910, int irq,
-		    struct tps65910_platform_data *pdata)
-{
-	int ret;
-	int flags = IRQF_ONESHOT;
-
-	if (!irq) {
-		dev_warn(tps65910->dev, "No interrupt support, no core IRQ\n");
-		return -EINVAL;
-	}
-
-	if (!pdata) {
-		dev_warn(tps65910->dev, "No interrupt support, no pdata\n");
-		return -EINVAL;
-	}
-
-	switch (tps65910_chip_id(tps65910)) {
-	case TPS65910:
-		tps65910->irq_num = TPS65910_NUM_IRQ;
-		break;
-	case TPS65911:
-		tps65910->irq_num = TPS65911_NUM_IRQ;
-		break;
-	}
-
-	if (pdata->irq_base > 0) {
-		pdata->irq_base = irq_alloc_descs(pdata->irq_base, 0,
-					tps65910->irq_num, -1);
-		if (pdata->irq_base < 0) {
-			dev_warn(tps65910->dev, "Failed to alloc IRQs: %d\n",
-					pdata->irq_base);
-			return pdata->irq_base;
-		}
-	}
-
-	tps65910->irq_mask = 0xFFFFFF;
-
-	mutex_init(&tps65910->irq_lock);
-	tps65910->chip_irq = irq;
-	tps65910->irq_base = pdata->irq_base;
-
-	if (pdata->irq_base > 0)
-		tps65910->domain = irq_domain_add_legacy(tps65910->dev->of_node,
-					tps65910->irq_num,
-					pdata->irq_base,
-					0,
-					&tps65910_domain_ops, tps65910);
-	else
-		tps65910->domain = irq_domain_add_linear(tps65910->dev->of_node,
-					tps65910->irq_num,
-					&tps65910_domain_ops, tps65910);
-
-	if (!tps65910->domain) {
-		dev_err(tps65910->dev, "Failed to create IRQ domain\n");
-		return -ENOMEM;
-	}
-
-	ret = request_threaded_irq(irq, NULL, tps65910_irq, flags,
-				   "tps65910", tps65910);
-
-	irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
-
-	if (ret != 0)
-		dev_err(tps65910->dev, "Failed to request IRQ: %d\n", ret);
-
-	return ret;
-}
-
-int tps65910_irq_exit(struct tps65910 *tps65910)
-{
-	if (tps65910->chip_irq)
-		free_irq(tps65910->chip_irq, tps65910);
-	return 0;
-}
diff --git a/drivers/mfd/tps65910.c b/drivers/mfd/tps65910.c
index ce05465..d792772 100644
--- a/drivers/mfd/tps65910.c
+++ b/drivers/mfd/tps65910.c
@@ -19,6 +19,9 @@
 #include <linux/err.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
 #include <linux/mfd/core.h>
 #include <linux/regmap.h>
 #include <linux/mfd/tps65910.h>
@@ -50,6 +53,219 @@
 };
 
 
+static const struct regmap_irq tps65911_irqs[] = {
+	/* INT_STS */
+	[TPS65911_IRQ_PWRHOLD_F] = {
+		.mask = INT_MSK_PWRHOLD_F_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_VBAT_VMHI] = {
+		.mask = INT_MSK_VMBHI_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_PWRON] = {
+		.mask = INT_MSK_PWRON_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_PWRON_LP] = {
+		.mask = INT_MSK_PWRON_LP_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_PWRHOLD_R] = {
+		.mask = INT_MSK_PWRHOLD_R_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_HOTDIE] = {
+		.mask = INT_MSK_HOTDIE_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_RTC_ALARM] = {
+		.mask = INT_MSK_RTC_ALARM_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65911_IRQ_RTC_PERIOD] = {
+		.mask = INT_MSK_RTC_PERIOD_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+
+	/* INT_STS2 */
+	[TPS65911_IRQ_GPIO0_R] = {
+		.mask = INT_MSK2_GPIO0_R_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO0_F] = {
+		.mask = INT_MSK2_GPIO0_F_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO1_R] = {
+		.mask = INT_MSK2_GPIO1_R_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO1_F] = {
+		.mask = INT_MSK2_GPIO1_F_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO2_R] = {
+		.mask = INT_MSK2_GPIO2_R_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO2_F] = {
+		.mask = INT_MSK2_GPIO2_F_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO3_R] = {
+		.mask = INT_MSK2_GPIO3_R_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65911_IRQ_GPIO3_F] = {
+		.mask = INT_MSK2_GPIO3_F_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+
+	/* INT_STS2 */
+	[TPS65911_IRQ_GPIO4_R] = {
+		.mask = INT_MSK3_GPIO4_R_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_GPIO4_F] = {
+		.mask = INT_MSK3_GPIO4_F_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_GPIO5_R] = {
+		.mask = INT_MSK3_GPIO5_R_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_GPIO5_F] = {
+		.mask = INT_MSK3_GPIO5_F_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_WTCHDG] = {
+		.mask = INT_MSK3_WTCHDG_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_VMBCH2_H] = {
+		.mask = INT_MSK3_VMBCH2_H_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_VMBCH2_L] = {
+		.mask = INT_MSK3_VMBCH2_L_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+	[TPS65911_IRQ_PWRDN] = {
+		.mask = INT_MSK3_PWRDN_IT_MSK_MASK,
+		.reg_offset = 2,
+	},
+};
+
+static const struct regmap_irq tps65910_irqs[] = {
+	/* INT_STS */
+	[TPS65910_IRQ_VBAT_VMBDCH] = {
+		.mask = TPS65910_INT_MSK_VMBDCH_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_VBAT_VMHI] = {
+		.mask = TPS65910_INT_MSK_VMBHI_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_PWRON] = {
+		.mask = TPS65910_INT_MSK_PWRON_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_PWRON_LP] = {
+		.mask = TPS65910_INT_MSK_PWRON_LP_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_PWRHOLD] = {
+		.mask = TPS65910_INT_MSK_PWRHOLD_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_HOTDIE] = {
+		.mask = TPS65910_INT_MSK_HOTDIE_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_RTC_ALARM] = {
+		.mask = TPS65910_INT_MSK_RTC_ALARM_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+	[TPS65910_IRQ_RTC_PERIOD] = {
+		.mask = TPS65910_INT_MSK_RTC_PERIOD_IT_MSK_MASK,
+		.reg_offset = 0,
+	},
+
+	/* INT_STS2 */
+	[TPS65910_IRQ_GPIO_R] = {
+		.mask = TPS65910_INT_MSK2_GPIO0_F_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+	[TPS65910_IRQ_GPIO_F] = {
+		.mask = TPS65910_INT_MSK2_GPIO0_R_IT_MSK_MASK,
+		.reg_offset = 1,
+	},
+};
+
+static struct regmap_irq_chip tps65911_irq_chip = {
+	.name = "tps65910",
+	.irqs = tps65911_irqs,
+	.num_irqs = ARRAY_SIZE(tps65911_irqs),
+	.num_regs = 3,
+	.irq_reg_stride = 2,
+	.status_base = TPS65910_INT_STS,
+	.mask_base = TPS65910_INT_MSK,
+	.ack_base = TPS65910_INT_STS,
+};
+
+static struct regmap_irq_chip tps65910_irq_chip = {
+	.name = "tps65910",
+	.irqs = tps65910_irqs,
+	.num_irqs = ARRAY_SIZE(tps65910_irqs),
+	.num_regs = 2,
+	.irq_reg_stride = 2,
+	.status_base = TPS65910_INT_STS,
+	.mask_base = TPS65910_INT_MSK,
+	.ack_base = TPS65910_INT_STS,
+};
+
+static int tps65910_irq_init(struct tps65910 *tps65910, int irq,
+		    struct tps65910_platform_data *pdata)
+{
+	int ret = 0;
+	static struct regmap_irq_chip *tps6591x_irqs_chip;
+
+	if (!irq) {
+		dev_warn(tps65910->dev, "No interrupt support, no core IRQ\n");
+		return -EINVAL;
+	}
+
+	if (!pdata) {
+		dev_warn(tps65910->dev, "No interrupt support, no pdata\n");
+		return -EINVAL;
+	}
+
+	switch (tps65910_chip_id(tps65910)) {
+	case TPS65910:
+		tps6591x_irqs_chip = &tps65910_irq_chip;
+		break;
+	case TPS65911:
+		tps6591x_irqs_chip = &tps65911_irq_chip;
+		break;
+	}
+
+	tps65910->chip_irq = irq;
+	ret = regmap_add_irq_chip(tps65910->regmap, tps65910->chip_irq,
+		IRQF_ONESHOT, pdata->irq_base,
+		tps6591x_irqs_chip, &tps65910->irq_data);
+	if (ret < 0)
+		dev_warn(tps65910->dev, "Failed to add irq_chip %d\n", ret);
+	return ret;
+}
+
+static int tps65910_irq_exit(struct tps65910 *tps65910)
+{
+	if (tps65910->chip_irq > 0)
+		regmap_del_irq_chip(tps65910->chip_irq, tps65910->irq_data);
+	return 0;
+}
+
 static bool is_volatile_reg(struct device *dev, unsigned int reg)
 {
 	struct tps65910 *tps65910 = dev_get_drvdata(dev);
@@ -270,7 +486,6 @@
 	tps65910->dev = &i2c->dev;
 	tps65910->i2c_client = i2c;
 	tps65910->id = chip_id;
-	mutex_init(&tps65910->io_mutex);
 
 	tps65910->regmap = devm_regmap_init_i2c(i2c, &tps65910_regmap_config);
 	if (IS_ERR(tps65910->regmap)) {
@@ -279,14 +494,6 @@
 		return ret;
 	}
 
-	ret = mfd_add_devices(tps65910->dev, -1,
-			      tps65910s, ARRAY_SIZE(tps65910s),
-			      NULL, 0, NULL);
-	if (ret < 0) {
-		dev_err(&i2c->dev, "mfd_add_devices failed: %d\n", ret);
-		return ret;
-	}
-
 	init_data->irq = pmic_plat_data->irq;
 	init_data->irq_base = pmic_plat_data->irq_base;
 
@@ -299,6 +506,15 @@
 		pm_power_off = tps65910_power_off;
 	}
 
+	ret = mfd_add_devices(tps65910->dev, -1,
+			      tps65910s, ARRAY_SIZE(tps65910s),
+			      NULL, 0,
+			      regmap_irq_get_domain(tps65910->irq_data));
+	if (ret < 0) {
+		dev_err(&i2c->dev, "mfd_add_devices failed: %d\n", ret);
+		return ret;
+	}
+
 	return ret;
 }
 
diff --git a/drivers/mfd/tps80031.c b/drivers/mfd/tps80031.c
new file mode 100644
index 0000000..10b51f7
--- /dev/null
+++ b/drivers/mfd/tps80031.c
@@ -0,0 +1,574 @@
+/*
+ * tps80031.c -- TI TPS80031/TPS80032 mfd core driver.
+ *
+ * MFD core driver for TI TPS80031/TPS80032 Fully Integrated
+ * Power Management with Power Path and Battery Charger
+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <ldewangan@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/tps80031.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+static struct resource tps80031_rtc_resources[] = {
+	{
+		.start = TPS80031_INT_RTC_ALARM,
+		.end = TPS80031_INT_RTC_ALARM,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+/* TPS80031 sub mfd devices */
+static struct mfd_cell tps80031_cell[] = {
+	{
+		.name = "tps80031-pmic",
+	},
+	{
+		.name = "tps80031-clock",
+	},
+	{
+		.name = "tps80031-rtc",
+		.num_resources = ARRAY_SIZE(tps80031_rtc_resources),
+		.resources = tps80031_rtc_resources,
+	},
+	{
+		.name = "tps80031-gpadc",
+	},
+	{
+		.name = "tps80031-fuel-gauge",
+	},
+	{
+		.name = "tps80031-charger",
+	},
+};
+
+static int tps80031_slave_address[TPS80031_NUM_SLAVES] = {
+	TPS80031_I2C_ID0_ADDR,
+	TPS80031_I2C_ID1_ADDR,
+	TPS80031_I2C_ID2_ADDR,
+	TPS80031_I2C_ID3_ADDR,
+};
+
+struct tps80031_pupd_data {
+	u8	reg;
+	u8	pullup_bit;
+	u8	pulldown_bit;
+};
+
+#define TPS80031_IRQ(_reg, _mask)			\
+	{							\
+		.reg_offset = (TPS80031_INT_MSK_LINE_##_reg) -	\
+				TPS80031_INT_MSK_LINE_A,	\
+		.mask = BIT(_mask),				\
+	}
+
+static const struct regmap_irq tps80031_main_irqs[] = {
+	[TPS80031_INT_PWRON]		= TPS80031_IRQ(A, 0),
+	[TPS80031_INT_RPWRON]		= TPS80031_IRQ(A, 1),
+	[TPS80031_INT_SYS_VLOW]		= TPS80031_IRQ(A, 2),
+	[TPS80031_INT_RTC_ALARM]	= TPS80031_IRQ(A, 3),
+	[TPS80031_INT_RTC_PERIOD]	= TPS80031_IRQ(A, 4),
+	[TPS80031_INT_HOT_DIE]		= TPS80031_IRQ(A, 5),
+	[TPS80031_INT_VXX_SHORT]	= TPS80031_IRQ(A, 6),
+	[TPS80031_INT_SPDURATION]	= TPS80031_IRQ(A, 7),
+	[TPS80031_INT_WATCHDOG]		= TPS80031_IRQ(B, 0),
+	[TPS80031_INT_BAT]		= TPS80031_IRQ(B, 1),
+	[TPS80031_INT_SIM]		= TPS80031_IRQ(B, 2),
+	[TPS80031_INT_MMC]		= TPS80031_IRQ(B, 3),
+	[TPS80031_INT_RES]		= TPS80031_IRQ(B, 4),
+	[TPS80031_INT_GPADC_RT]		= TPS80031_IRQ(B, 5),
+	[TPS80031_INT_GPADC_SW2_EOC]	= TPS80031_IRQ(B, 6),
+	[TPS80031_INT_CC_AUTOCAL]	= TPS80031_IRQ(B, 7),
+	[TPS80031_INT_ID_WKUP]		= TPS80031_IRQ(C, 0),
+	[TPS80031_INT_VBUSS_WKUP]	= TPS80031_IRQ(C, 1),
+	[TPS80031_INT_ID]		= TPS80031_IRQ(C, 2),
+	[TPS80031_INT_VBUS]		= TPS80031_IRQ(C, 3),
+	[TPS80031_INT_CHRG_CTRL]	= TPS80031_IRQ(C, 4),
+	[TPS80031_INT_EXT_CHRG]		= TPS80031_IRQ(C, 5),
+	[TPS80031_INT_INT_CHRG]		= TPS80031_IRQ(C, 6),
+	[TPS80031_INT_RES2]		= TPS80031_IRQ(C, 7),
+};
+
+static struct regmap_irq_chip tps80031_irq_chip = {
+	.name = "tps80031",
+	.irqs = tps80031_main_irqs,
+	.num_irqs = ARRAY_SIZE(tps80031_main_irqs),
+	.num_regs = 3,
+	.status_base = TPS80031_INT_STS_A,
+	.mask_base = TPS80031_INT_MSK_LINE_A,
+};
+
+#define PUPD_DATA(_reg, _pulldown_bit, _pullup_bit)	\
+	{						\
+		.reg = TPS80031_CFG_INPUT_PUPD##_reg,	\
+		.pulldown_bit = _pulldown_bit,		\
+		.pullup_bit = _pullup_bit,		\
+	}
+
+static const struct tps80031_pupd_data tps80031_pupds[] = {
+	[TPS80031_PREQ1]		= PUPD_DATA(1, BIT(0),	BIT(1)),
+	[TPS80031_PREQ2A]		= PUPD_DATA(1, BIT(2),	BIT(3)),
+	[TPS80031_PREQ2B]		= PUPD_DATA(1, BIT(4),	BIT(5)),
+	[TPS80031_PREQ2C]		= PUPD_DATA(1, BIT(6),	BIT(7)),
+	[TPS80031_PREQ3]		= PUPD_DATA(2, BIT(0),	BIT(1)),
+	[TPS80031_NRES_WARM]		= PUPD_DATA(2, 0,	BIT(2)),
+	[TPS80031_PWM_FORCE]		= PUPD_DATA(2, BIT(5),	0),
+	[TPS80031_CHRG_EXT_CHRG_STATZ]	= PUPD_DATA(2, 0,	BIT(6)),
+	[TPS80031_SIM]			= PUPD_DATA(3, BIT(0),	BIT(1)),
+	[TPS80031_MMC]			= PUPD_DATA(3, BIT(2),	BIT(3)),
+	[TPS80031_GPADC_START]		= PUPD_DATA(3, BIT(4),	0),
+	[TPS80031_DVSI2C_SCL]		= PUPD_DATA(4, 0,	BIT(0)),
+	[TPS80031_DVSI2C_SDA]		= PUPD_DATA(4, 0,	BIT(1)),
+	[TPS80031_CTLI2C_SCL]		= PUPD_DATA(4, 0,	BIT(2)),
+	[TPS80031_CTLI2C_SDA]		= PUPD_DATA(4, 0,	BIT(3)),
+};
+static struct tps80031 *tps80031_power_off_dev;
+
+int tps80031_ext_power_req_config(struct device *dev,
+		unsigned long ext_ctrl_flag, int preq_bit,
+		int state_reg_add, int trans_reg_add)
+{
+	u8 res_ass_reg = 0;
+	int preq_mask_bit = 0;
+	int ret;
+
+	if (!(ext_ctrl_flag & TPS80031_EXT_PWR_REQ))
+		return 0;
+
+	if (ext_ctrl_flag & TPS80031_PWR_REQ_INPUT_PREQ1) {
+		res_ass_reg = TPS80031_PREQ1_RES_ASS_A + (preq_bit >> 3);
+		preq_mask_bit = 5;
+	} else if (ext_ctrl_flag & TPS80031_PWR_REQ_INPUT_PREQ2) {
+		res_ass_reg = TPS80031_PREQ2_RES_ASS_A + (preq_bit >> 3);
+		preq_mask_bit = 6;
+	} else if (ext_ctrl_flag & TPS80031_PWR_REQ_INPUT_PREQ3) {
+		res_ass_reg = TPS80031_PREQ3_RES_ASS_A + (preq_bit >> 3);
+		preq_mask_bit = 7;
+	}
+
+	/* Configure REQ_ASS registers */
+	ret = tps80031_set_bits(dev, TPS80031_SLAVE_ID1, res_ass_reg,
+					BIT(preq_bit & 0x7));
+	if (ret < 0) {
+		dev_err(dev, "reg 0x%02x setbit failed, err = %d\n",
+				res_ass_reg, ret);
+		return ret;
+	}
+
+	/* Unmask the PREQ */
+	ret = tps80031_clr_bits(dev, TPS80031_SLAVE_ID1,
+			TPS80031_PHOENIX_MSK_TRANSITION, BIT(preq_mask_bit));
+	if (ret < 0) {
+		dev_err(dev, "reg 0x%02x clrbit failed, err = %d\n",
+			TPS80031_PHOENIX_MSK_TRANSITION, ret);
+		return ret;
+	}
+
+	/* Switch regulator control to resource now */
+	if (ext_ctrl_flag & (TPS80031_PWR_REQ_INPUT_PREQ2 |
+					TPS80031_PWR_REQ_INPUT_PREQ3)) {
+		ret = tps80031_update(dev, TPS80031_SLAVE_ID1, state_reg_add,
+						0x0, TPS80031_STATE_MASK);
+		if (ret < 0)
+			dev_err(dev, "reg 0x%02x update failed, err = %d\n",
+				state_reg_add, ret);
+	} else {
+		ret = tps80031_update(dev, TPS80031_SLAVE_ID1, trans_reg_add,
+				TPS80031_TRANS_SLEEP_OFF,
+				TPS80031_TRANS_SLEEP_MASK);
+		if (ret < 0)
+			dev_err(dev, "reg 0x%02x update failed, err = %d\n",
+				trans_reg_add, ret);
+	}
+	return ret;
+}
+EXPORT_SYMBOL_GPL(tps80031_ext_power_req_config);
+
+static void tps80031_power_off(void)
+{
+	dev_info(tps80031_power_off_dev->dev, "switching off PMU\n");
+	tps80031_write(tps80031_power_off_dev->dev, TPS80031_SLAVE_ID1,
+				TPS80031_PHOENIX_DEV_ON, TPS80031_DEVOFF);
+}
+
+static void tps80031_pupd_init(struct tps80031 *tps80031,
+			       struct tps80031_platform_data *pdata)
+{
+	struct tps80031_pupd_init_data *pupd_init_data = pdata->pupd_init_data;
+	int data_size = pdata->pupd_init_data_size;
+	int i;
+
+	for (i = 0; i < data_size; ++i) {
+		struct tps80031_pupd_init_data *pupd_init = &pupd_init_data[i];
+		const struct tps80031_pupd_data *pupd =
+			&tps80031_pupds[pupd_init->input_pin];
+		u8 update_value = 0;
+		u8 update_mask = pupd->pulldown_bit | pupd->pullup_bit;
+
+		if (pupd_init->setting == TPS80031_PUPD_PULLDOWN)
+			update_value = pupd->pulldown_bit;
+		else if (pupd_init->setting == TPS80031_PUPD_PULLUP)
+			update_value = pupd->pullup_bit;
+
+		tps80031_update(tps80031->dev, TPS80031_SLAVE_ID1, pupd->reg,
+				update_value, update_mask);
+	}
+}
+
+static int tps80031_init_ext_control(struct tps80031 *tps80031,
+			struct tps80031_platform_data *pdata)
+{
+	struct device *dev = tps80031->dev;
+	int ret;
+	int i;
+
+	/* Clear all external control for this rail */
+	for (i = 0; i < 9; ++i) {
+		ret = tps80031_write(dev, TPS80031_SLAVE_ID1,
+				TPS80031_PREQ1_RES_ASS_A + i, 0);
+		if (ret < 0) {
+			dev_err(dev, "reg 0x%02x write failed, err = %d\n",
+				TPS80031_PREQ1_RES_ASS_A + i, ret);
+			return ret;
+		}
+	}
+
+	/* Mask the PREQ */
+	ret = tps80031_set_bits(dev, TPS80031_SLAVE_ID1,
+			TPS80031_PHOENIX_MSK_TRANSITION, 0x7 << 5);
+	if (ret < 0) {
+		dev_err(dev, "reg 0x%02x set_bits failed, err = %d\n",
+			TPS80031_PHOENIX_MSK_TRANSITION, ret);
+		return ret;
+	}
+	return ret;
+}
+
+static int __devinit tps80031_irq_init(struct tps80031 *tps80031, int irq,
+				int irq_base)
+{
+	struct device *dev = tps80031->dev;
+	int i, ret;
+
+	/*
+	 * The MASK register used for updating status register when
+	 * interrupt occurs and LINE register used to pass the status
+	 * to actual interrupt line.  As per datasheet:
+	 * When INT_MSK_LINE [i] is set to 1, the associated interrupt
+	 * number i is INT line masked, which means that no interrupt is
+	 * generated on the INT line.
+	 * When INT_MSK_LINE [i] is set to 0, the associated interrupt
+	 * number i is  line enabled: An interrupt is generated on the
+	 * INT line.
+	 * In any case, the INT_STS [i] status bit may or may not be updated,
+	 * only linked to the INT_MSK_STS [i] configuration register bit.
+	 *
+	 * When INT_MSK_STS [i] is set to 1, the associated interrupt number
+	 * i is status masked, which means that no interrupt is stored in
+	 * the INT_STS[i] status bit. Note that no interrupt number i is
+	 * generated on the INT line, even if the INT_MSK_LINE [i] register
+	 * bit is set to 0.
+	 * When INT_MSK_STS [i] is set to 0, the associated interrupt number i
+	 * is status enabled: An interrupt status is updated in the INT_STS [i]
+	 * register. The interrupt may or may not be generated on the INT line,
+	 * depending on the INT_MSK_LINE [i] configuration register bit.
+	 */
+	for (i = 0; i < 3; i++)
+		tps80031_write(dev, TPS80031_SLAVE_ID2,
+				TPS80031_INT_MSK_STS_A + i, 0x00);
+
+	ret = regmap_add_irq_chip(tps80031->regmap[TPS80031_SLAVE_ID2], irq,
+			IRQF_ONESHOT, irq_base,
+			&tps80031_irq_chip, &tps80031->irq_data);
+	if (ret < 0) {
+		dev_err(dev, "add irq failed, err = %d\n", ret);
+		return ret;
+	}
+	return ret;
+}
+
+static bool rd_wr_reg_id0(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case TPS80031_SMPS1_CFG_FORCE ... TPS80031_SMPS2_CFG_VOLTAGE:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool rd_wr_reg_id1(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case TPS80031_SECONDS_REG ... TPS80031_RTC_RESET_STATUS_REG:
+	case TPS80031_VALIDITY0 ... TPS80031_VALIDITY7:
+	case TPS80031_PHOENIX_START_CONDITION ... TPS80031_KEY_PRESS_DUR_CFG:
+	case TPS80031_SMPS4_CFG_TRANS ... TPS80031_SMPS3_CFG_VOLTAGE:
+	case TPS80031_BROADCAST_ADDR_ALL ... TPS80031_BROADCAST_ADDR_CLK_RST:
+	case TPS80031_VANA_CFG_TRANS ... TPS80031_LDO7_CFG_VOLTAGE:
+	case TPS80031_REGEN1_CFG_TRANS ... TPS80031_TMP_CFG_STATE:
+	case TPS80031_PREQ1_RES_ASS_A ... TPS80031_PREQ3_RES_ASS_C:
+	case TPS80031_SMPS_OFFSET ... TPS80031_BATDEBOUNCING:
+	case TPS80031_CFG_INPUT_PUPD1 ... TPS80031_CFG_SMPS_PD:
+	case TPS80031_BACKUP_REG:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool is_volatile_reg_id1(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case TPS80031_SMPS4_CFG_TRANS ... TPS80031_SMPS3_CFG_VOLTAGE:
+	case TPS80031_VANA_CFG_TRANS ... TPS80031_LDO7_CFG_VOLTAGE:
+	case TPS80031_REGEN1_CFG_TRANS ... TPS80031_TMP_CFG_STATE:
+	case TPS80031_PREQ1_RES_ASS_A ... TPS80031_PREQ3_RES_ASS_C:
+	case TPS80031_SMPS_OFFSET ... TPS80031_BATDEBOUNCING:
+	case TPS80031_CFG_INPUT_PUPD1 ... TPS80031_CFG_SMPS_PD:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool rd_wr_reg_id2(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case TPS80031_USB_VENDOR_ID_LSB ... TPS80031_USB_OTG_REVISION:
+	case TPS80031_GPADC_CTRL ... TPS80031_CTRL_P1:
+	case TPS80031_RTCH0_LSB ... TPS80031_GPCH0_MSB:
+	case TPS80031_TOGGLE1 ... TPS80031_VIBMODE:
+	case TPS80031_PWM1ON ... TPS80031_PWM2OFF:
+	case TPS80031_FG_REG_00 ... TPS80031_FG_REG_11:
+	case TPS80031_INT_STS_A ... TPS80031_INT_MSK_STS_C:
+	case TPS80031_CONTROLLER_CTRL2 ... TPS80031_LED_PWM_CTRL2:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool rd_wr_reg_id3(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case TPS80031_GPADC_TRIM0 ... TPS80031_GPADC_TRIM18:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static const struct regmap_config tps80031_regmap_configs[] = {
+	{
+		.reg_bits = 8,
+		.val_bits = 8,
+		.writeable_reg = rd_wr_reg_id0,
+		.readable_reg = rd_wr_reg_id0,
+		.max_register = TPS80031_MAX_REGISTER,
+	},
+	{
+		.reg_bits = 8,
+		.val_bits = 8,
+		.writeable_reg = rd_wr_reg_id1,
+		.readable_reg = rd_wr_reg_id1,
+		.volatile_reg = is_volatile_reg_id1,
+		.max_register = TPS80031_MAX_REGISTER,
+	},
+	{
+		.reg_bits = 8,
+		.val_bits = 8,
+		.writeable_reg = rd_wr_reg_id2,
+		.readable_reg = rd_wr_reg_id2,
+		.max_register = TPS80031_MAX_REGISTER,
+	},
+	{
+		.reg_bits = 8,
+		.val_bits = 8,
+		.writeable_reg = rd_wr_reg_id3,
+		.readable_reg = rd_wr_reg_id3,
+		.max_register = TPS80031_MAX_REGISTER,
+	},
+};
+
+static int __devinit tps80031_probe(struct i2c_client *client,
+					const struct i2c_device_id *id)
+{
+	struct tps80031_platform_data *pdata = client->dev.platform_data;
+	struct tps80031 *tps80031;
+	int ret;
+	uint8_t es_version;
+	uint8_t ep_ver;
+	int i;
+
+	if (!pdata) {
+		dev_err(&client->dev, "tps80031 requires platform data\n");
+		return -EINVAL;
+	}
+
+	tps80031 = devm_kzalloc(&client->dev, sizeof(*tps80031), GFP_KERNEL);
+	if (!tps80031) {
+		dev_err(&client->dev, "Malloc failed for tps80031\n");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < TPS80031_NUM_SLAVES; i++) {
+		if (tps80031_slave_address[i] == client->addr)
+			tps80031->clients[i] = client;
+		else
+			tps80031->clients[i] = i2c_new_dummy(client->adapter,
+						tps80031_slave_address[i]);
+		if (!tps80031->clients[i]) {
+			dev_err(&client->dev, "can't attach client %d\n", i);
+			ret = -ENOMEM;
+			goto fail_client_reg;
+		}
+
+		i2c_set_clientdata(tps80031->clients[i], tps80031);
+		tps80031->regmap[i] = devm_regmap_init_i2c(tps80031->clients[i],
+					&tps80031_regmap_configs[i]);
+		if (IS_ERR(tps80031->regmap[i])) {
+			ret = PTR_ERR(tps80031->regmap[i]);
+			dev_err(&client->dev,
+				"regmap %d init failed, err %d\n", i, ret);
+			goto fail_client_reg;
+		}
+	}
+
+	ret = tps80031_read(&client->dev, TPS80031_SLAVE_ID3,
+			TPS80031_JTAGVERNUM, &es_version);
+	if (ret < 0) {
+		dev_err(&client->dev,
+			"Silicon version number read failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	ret = tps80031_read(&client->dev, TPS80031_SLAVE_ID3,
+			TPS80031_EPROM_REV, &ep_ver);
+	if (ret < 0) {
+		dev_err(&client->dev,
+			"Silicon eeprom version read failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	dev_info(&client->dev, "ES version 0x%02x and EPROM version 0x%02x\n",
+					es_version, ep_ver);
+	tps80031->es_version = es_version;
+	tps80031->dev = &client->dev;
+	i2c_set_clientdata(client, tps80031);
+	tps80031->chip_info = id->driver_data;
+
+	ret = tps80031_irq_init(tps80031, client->irq, pdata->irq_base);
+	if (ret) {
+		dev_err(&client->dev, "IRQ init failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	tps80031_pupd_init(tps80031, pdata);
+
+	tps80031_init_ext_control(tps80031, pdata);
+
+	ret = mfd_add_devices(tps80031->dev, -1,
+			tps80031_cell, ARRAY_SIZE(tps80031_cell),
+			NULL, 0,
+			regmap_irq_get_domain(tps80031->irq_data));
+	if (ret < 0) {
+		dev_err(&client->dev, "mfd_add_devices failed: %d\n", ret);
+		goto fail_mfd_add;
+	}
+
+	if (pdata->use_power_off && !pm_power_off) {
+		tps80031_power_off_dev = tps80031;
+		pm_power_off = tps80031_power_off;
+	}
+	return 0;
+
+fail_mfd_add:
+	regmap_del_irq_chip(client->irq, tps80031->irq_data);
+
+fail_client_reg:
+	for (i = 0; i < TPS80031_NUM_SLAVES; i++) {
+		if (tps80031->clients[i]  && (tps80031->clients[i] != client))
+			i2c_unregister_device(tps80031->clients[i]);
+	}
+	return ret;
+}
+
+static int __devexit tps80031_remove(struct i2c_client *client)
+{
+	struct tps80031 *tps80031 = i2c_get_clientdata(client);
+	int i;
+
+	if (tps80031_power_off_dev == tps80031) {
+		tps80031_power_off_dev = NULL;
+		pm_power_off = NULL;
+	}
+
+	mfd_remove_devices(tps80031->dev);
+
+	regmap_del_irq_chip(client->irq, tps80031->irq_data);
+
+	for (i = 0; i < TPS80031_NUM_SLAVES; i++) {
+		if (tps80031->clients[i] != client)
+			i2c_unregister_device(tps80031->clients[i]);
+	}
+	return 0;
+}
+
+static const struct i2c_device_id tps80031_id_table[] = {
+	{ "tps80031", TPS80031 },
+	{ "tps80032", TPS80032 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, tps80031_id_table);
+
+static struct i2c_driver tps80031_driver = {
+	.driver	= {
+		.name	= "tps80031",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= tps80031_probe,
+	.remove		= __devexit_p(tps80031_remove),
+	.id_table	= tps80031_id_table,
+};
+
+static int __init tps80031_init(void)
+{
+	return i2c_add_driver(&tps80031_driver);
+}
+subsys_initcall(tps80031_init);
+
+static void __exit tps80031_exit(void)
+{
+	i2c_del_driver(&tps80031_driver);
+}
+module_exit(tps80031_exit);
+
+MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
+MODULE_DESCRIPTION("TPS80031 core driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c
index 11b76c0..4f3baad 100644
--- a/drivers/mfd/twl-core.c
+++ b/drivers/mfd/twl-core.c
@@ -32,6 +32,7 @@
 #include <linux/mutex.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/device.h>
@@ -65,9 +66,6 @@
 
 /* Triton Core internal information (BEGIN) */
 
-/* Last - for index max*/
-#define TWL4030_MODULE_LAST		TWL4030_MODULE_SECURED_REG
-
 #define TWL_NUM_SLAVES		4
 
 #define SUB_CHIP_ID0 0
@@ -171,13 +169,7 @@
 /* Structure for each TWL4030/TWL6030 Slave */
 struct twl_client {
 	struct i2c_client *client;
-	u8 address;
-
-	/* max numb of i2c_msg required is for read =2 */
-	struct i2c_msg xfer_msg[2];
-
-	/* To lock access to xfer_msg */
-	struct mutex xfer_lock;
+	struct regmap *regmap;
 };
 
 static struct twl_client twl_modules[TWL_NUM_SLAVES];
@@ -189,7 +181,7 @@
 };
 static struct twl_mapping *twl_map;
 
-static struct twl_mapping twl4030_map[TWL4030_MODULE_LAST + 1] = {
+static struct twl_mapping twl4030_map[] = {
 	/*
 	 * NOTE:  don't change this table without updating the
 	 * <linux/i2c/twl.h> defines for TWL4030_MODULE_*
@@ -197,34 +189,62 @@
 	 */
 
 	{ 0, TWL4030_BASEADD_USB },
-
 	{ 1, TWL4030_BASEADD_AUDIO_VOICE },
 	{ 1, TWL4030_BASEADD_GPIO },
 	{ 1, TWL4030_BASEADD_INTBR },
 	{ 1, TWL4030_BASEADD_PIH },
-	{ 1, TWL4030_BASEADD_TEST },
 
+	{ 1, TWL4030_BASEADD_TEST },
 	{ 2, TWL4030_BASEADD_KEYPAD },
 	{ 2, TWL4030_BASEADD_MADC },
 	{ 2, TWL4030_BASEADD_INTERRUPTS },
 	{ 2, TWL4030_BASEADD_LED },
+
 	{ 2, TWL4030_BASEADD_MAIN_CHARGE },
 	{ 2, TWL4030_BASEADD_PRECHARGE },
 	{ 2, TWL4030_BASEADD_PWM0 },
 	{ 2, TWL4030_BASEADD_PWM1 },
 	{ 2, TWL4030_BASEADD_PWMA },
+
 	{ 2, TWL4030_BASEADD_PWMB },
 	{ 2, TWL5031_BASEADD_ACCESSORY },
 	{ 2, TWL5031_BASEADD_INTERRUPTS },
-
 	{ 3, TWL4030_BASEADD_BACKUP },
 	{ 3, TWL4030_BASEADD_INT },
+
 	{ 3, TWL4030_BASEADD_PM_MASTER },
 	{ 3, TWL4030_BASEADD_PM_RECEIVER },
 	{ 3, TWL4030_BASEADD_RTC },
 	{ 3, TWL4030_BASEADD_SECURED_REG },
 };
 
+static struct regmap_config twl4030_regmap_config[4] = {
+	{
+		/* Address 0x48 */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+	{
+		/* Address 0x49 */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+	{
+		/* Address 0x4a */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+	{
+		/* Address 0x4b */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+};
+
 static struct twl_mapping twl6030_map[] = {
 	/*
 	 * NOTE:  don't change this table without updating the
@@ -254,14 +274,35 @@
 	{ SUB_CHIP_ID2, TWL6030_BASEADD_RSV },
 	{ SUB_CHIP_ID2, TWL6030_BASEADD_RSV },
 	{ SUB_CHIP_ID2, TWL6030_BASEADD_RSV },
+
 	{ SUB_CHIP_ID0, TWL6030_BASEADD_PM_MASTER },
 	{ SUB_CHIP_ID0, TWL6030_BASEADD_PM_SLAVE_MISC },
-
 	{ SUB_CHIP_ID0, TWL6030_BASEADD_RTC },
 	{ SUB_CHIP_ID0, TWL6030_BASEADD_MEM },
 	{ SUB_CHIP_ID1, TWL6025_BASEADD_CHARGER },
 };
 
+static struct regmap_config twl6030_regmap_config[3] = {
+	{
+		/* Address 0x48 */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+	{
+		/* Address 0x49 */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+	{
+		/* Address 0x4a */
+		.reg_bits = 8,
+		.val_bits = 8,
+		.max_register = 0xff,
+	},
+};
+
 /*----------------------------------------------------------------------*/
 
 /* Exported Functions */
@@ -283,9 +324,8 @@
 	int ret;
 	int sid;
 	struct twl_client *twl;
-	struct i2c_msg *msg;
 
-	if (unlikely(mod_no > TWL_MODULE_LAST)) {
+	if (unlikely(mod_no >= TWL_MODULE_LAST)) {
 		pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no);
 		return -EPERM;
 	}
@@ -301,32 +341,14 @@
 	}
 	twl = &twl_modules[sid];
 
-	mutex_lock(&twl->xfer_lock);
-	/*
-	 * [MSG1]: fill the register address data
-	 * fill the data Tx buffer
-	 */
-	msg = &twl->xfer_msg[0];
-	msg->addr = twl->address;
-	msg->len = num_bytes + 1;
-	msg->flags = 0;
-	msg->buf = value;
-	/* over write the first byte of buffer with the register address */
-	*value = twl_map[mod_no].base + reg;
-	ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 1);
-	mutex_unlock(&twl->xfer_lock);
+	ret = regmap_bulk_write(twl->regmap, twl_map[mod_no].base + reg,
+				value, num_bytes);
 
-	/* i2c_transfer returns number of messages transferred */
-	if (ret != 1) {
-		pr_err("%s: i2c_write failed to transfer all messages\n",
-			DRIVER_NAME);
-		if (ret < 0)
-			return ret;
-		else
-			return -EIO;
-	} else {
-		return 0;
-	}
+	if (ret)
+		pr_err("%s: Write failed (mod %d, reg 0x%02x count %d)\n",
+		       DRIVER_NAME, mod_no, reg, num_bytes);
+
+	return ret;
 }
 EXPORT_SYMBOL(twl_i2c_write);
 
@@ -342,12 +364,10 @@
 int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes)
 {
 	int ret;
-	u8 val;
 	int sid;
 	struct twl_client *twl;
-	struct i2c_msg *msg;
 
-	if (unlikely(mod_no > TWL_MODULE_LAST)) {
+	if (unlikely(mod_no >= TWL_MODULE_LAST)) {
 		pr_err("%s: invalid module number %d\n", DRIVER_NAME, mod_no);
 		return -EPERM;
 	}
@@ -363,34 +383,14 @@
 	}
 	twl = &twl_modules[sid];
 
-	mutex_lock(&twl->xfer_lock);
-	/* [MSG1] fill the register address data */
-	msg = &twl->xfer_msg[0];
-	msg->addr = twl->address;
-	msg->len = 1;
-	msg->flags = 0;	/* Read the register value */
-	val = twl_map[mod_no].base + reg;
-	msg->buf = &val;
-	/* [MSG2] fill the data rx buffer */
-	msg = &twl->xfer_msg[1];
-	msg->addr = twl->address;
-	msg->flags = I2C_M_RD;	/* Read the register value */
-	msg->len = num_bytes;	/* only n bytes */
-	msg->buf = value;
-	ret = i2c_transfer(twl->client->adapter, twl->xfer_msg, 2);
-	mutex_unlock(&twl->xfer_lock);
+	ret = regmap_bulk_read(twl->regmap, twl_map[mod_no].base + reg,
+			       value, num_bytes);
 
-	/* i2c_transfer returns number of messages transferred */
-	if (ret != 2) {
-		pr_err("%s: i2c_read failed to transfer all messages\n",
-			DRIVER_NAME);
-		if (ret < 0)
-			return ret;
-		else
-			return -EIO;
-	} else {
-		return 0;
-	}
+	if (ret)
+		pr_err("%s: Read failed (mod %d, reg 0x%02x count %d)\n",
+		       DRIVER_NAME, mod_no, reg, num_bytes);
+
+	return ret;
 }
 EXPORT_SYMBOL(twl_i2c_read);
 
@@ -404,12 +404,7 @@
  */
 int twl_i2c_write_u8(u8 mod_no, u8 value, u8 reg)
 {
-
-	/* 2 bytes offset 1 contains the data offset 0 is used by i2c_write */
-	u8 temp_buffer[2] = { 0 };
-	/* offset 1 contains the data */
-	temp_buffer[1] = value;
-	return twl_i2c_write(mod_no, temp_buffer, reg, 1);
+	return twl_i2c_write(mod_no, &value, reg, 1);
 }
 EXPORT_SYMBOL(twl_i2c_write_u8);
 
@@ -646,8 +641,9 @@
 			return PTR_ERR(child);
 	}
 
-	if (IS_ENABLED(CONFIG_TWL4030_MADC) && pdata->madc) {
-		child = add_child(2, "twl4030_madc",
+	if (IS_ENABLED(CONFIG_TWL4030_MADC) && pdata->madc &&
+	    twl_class_is_4030()) {
+		child = add_child(SUB_CHIP_ID2, "twl4030_madc",
 				pdata->madc, sizeof(*pdata->madc),
 				true, irq_base + MADC_INTR_OFFSET, 0);
 		if (IS_ERR(child))
@@ -663,15 +659,21 @@
 		 * HW security concerns, and "least privilege".
 		 */
 		sub_chip_id = twl_map[TWL_MODULE_RTC].sid;
-		child = add_child(sub_chip_id, "twl_rtc",
-				NULL, 0,
+		child = add_child(sub_chip_id, "twl_rtc", NULL, 0,
 				true, irq_base + RTC_INTR_OFFSET, 0);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
 	}
 
-	if (IS_ENABLED(CONFIG_PWM_TWL6030) && twl_class_is_6030()) {
-		child = add_child(SUB_CHIP_ID1, "twl6030-pwm", NULL, 0,
+	if (IS_ENABLED(CONFIG_PWM_TWL)) {
+		child = add_child(SUB_CHIP_ID1, "twl-pwm", NULL, 0,
+				  false, 0, 0);
+		if (IS_ERR(child))
+			return PTR_ERR(child);
+	}
+
+	if (IS_ENABLED(CONFIG_PWM_TWL_LED)) {
+		child = add_child(SUB_CHIP_ID1, "twl-pwmled", NULL, 0,
 				  false, 0, 0);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
@@ -723,9 +725,8 @@
 
 		}
 
-		child = add_child(0, "twl4030_usb",
-				pdata->usb, sizeof(*pdata->usb),
-				true,
+		child = add_child(SUB_CHIP_ID0, "twl4030_usb",
+				pdata->usb, sizeof(*pdata->usb), true,
 				/* irq0 = USB_PRES, irq1 = USB */
 				irq_base + USB_PRES_INTR_OFFSET,
 				irq_base + USB_INTR_OFFSET);
@@ -773,9 +774,8 @@
 
 		pdata->usb->features = features;
 
-		child = add_child(0, "twl6030_usb",
-			pdata->usb, sizeof(*pdata->usb),
-			true,
+		child = add_child(SUB_CHIP_ID0, "twl6030_usb",
+			pdata->usb, sizeof(*pdata->usb), true,
 			/* irq1 = VBUS_PRES, irq0 = USB ID */
 			irq_base + USBOTG_INTR_OFFSET,
 			irq_base + USB_PRES_INTR_OFFSET);
@@ -799,22 +799,22 @@
 	}
 
 	if (IS_ENABLED(CONFIG_TWL4030_WATCHDOG) && twl_class_is_4030()) {
-		child = add_child(0, "twl4030_wdt", NULL, 0, false, 0, 0);
+		child = add_child(SUB_CHIP_ID3, "twl4030_wdt", NULL, 0,
+				  false, 0, 0);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
 	}
 
 	if (IS_ENABLED(CONFIG_INPUT_TWL4030_PWRBUTTON) && twl_class_is_4030()) {
-		child = add_child(1, "twl4030_pwrbutton",
-				NULL, 0, true, irq_base + 8 + 0, 0);
+		child = add_child(SUB_CHIP_ID3, "twl4030_pwrbutton", NULL, 0,
+				  true, irq_base + 8 + 0, 0);
 		if (IS_ERR(child))
 			return PTR_ERR(child);
 	}
 
 	if (IS_ENABLED(CONFIG_MFD_TWL4030_AUDIO) && pdata->audio &&
 	    twl_class_is_4030()) {
-		sub_chip_id = twl_map[TWL_MODULE_AUDIO_VOICE].sid;
-		child = add_child(sub_chip_id, "twl4030-audio",
+		child = add_child(SUB_CHIP_ID1, "twl4030-audio",
 				pdata->audio, sizeof(*pdata->audio),
 				false, 0, 0);
 		if (IS_ERR(child))
@@ -1054,7 +1054,7 @@
 
 	if (IS_ENABLED(CONFIG_CHARGER_TWL4030) && pdata->bci &&
 			!(features & (TPS_SUBSET | TWL5031))) {
-		child = add_child(3, "twl4030_bci",
+		child = add_child(SUB_CHIP_ID3, "twl4030_bci",
 				pdata->bci, sizeof(*pdata->bci), false,
 				/* irq0 = CHG_PRES, irq1 = BCI */
 				irq_base + BCI_PRES_INTR_OFFSET,
@@ -1077,8 +1077,8 @@
 {
 	int e = 0;
 
-	e = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	e = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
+			     TWL4030_PM_MASTER_PROTECT_KEY);
 	return e;
 }
 
@@ -1086,12 +1086,10 @@
 {
 	int e = 0;
 
-	e |= twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG1,
-			TWL4030_PM_MASTER_PROTECT_KEY);
-	e |= twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG2,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	e |= twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
+			      TWL4030_PM_MASTER_PROTECT_KEY);
+	e |= twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
+			      TWL4030_PM_MASTER_PROTECT_KEY);
 
 	return e;
 }
@@ -1176,6 +1174,7 @@
 	struct twl4030_platform_data	*pdata = client->dev.platform_data;
 	struct device_node		*node = client->dev.of_node;
 	struct platform_device		*pdev;
+	struct regmap_config		*twl_regmap_config;
 	int				irq_base = 0;
 	int				status;
 	unsigned			i, num_slaves;
@@ -1229,22 +1228,23 @@
 	if ((id->driver_data) & TWL6030_CLASS) {
 		twl_id = TWL6030_CLASS_ID;
 		twl_map = &twl6030_map[0];
+		twl_regmap_config = twl6030_regmap_config;
 		num_slaves = TWL_NUM_SLAVES - 1;
 	} else {
 		twl_id = TWL4030_CLASS_ID;
 		twl_map = &twl4030_map[0];
+		twl_regmap_config = twl4030_regmap_config;
 		num_slaves = TWL_NUM_SLAVES;
 	}
 
 	for (i = 0; i < num_slaves; i++) {
 		struct twl_client *twl = &twl_modules[i];
 
-		twl->address = client->addr + i;
 		if (i == 0) {
 			twl->client = client;
 		} else {
 			twl->client = i2c_new_dummy(client->adapter,
-					twl->address);
+						    client->addr + i);
 			if (!twl->client) {
 				dev_err(&client->dev,
 					"can't attach client %d\n", i);
@@ -1252,7 +1252,16 @@
 				goto fail;
 			}
 		}
-		mutex_init(&twl->xfer_lock);
+
+		twl->regmap = devm_regmap_init_i2c(twl->client,
+						   &twl_regmap_config[i]);
+		if (IS_ERR(twl->regmap)) {
+			status = PTR_ERR(twl->regmap);
+			dev_err(&client->dev,
+				"Failed to allocate regmap %d, err: %d\n", i,
+				status);
+			goto fail;
+		}
 	}
 
 	inuse = true;
diff --git a/drivers/mfd/twl4030-irq.c b/drivers/mfd/twl4030-irq.c
index cdd1173..a5f9888 100644
--- a/drivers/mfd/twl4030-irq.c
+++ b/drivers/mfd/twl4030-irq.c
@@ -295,8 +295,8 @@
 	irqreturn_t	ret;
 	u8		pih_isr;
 
-	ret = twl_i2c_read_u8(TWL4030_MODULE_PIH, &pih_isr,
-			REG_PIH_ISR_P1);
+	ret = twl_i2c_read_u8(TWL_MODULE_PIH, &pih_isr,
+			      REG_PIH_ISR_P1);
 	if (ret) {
 		pr_warning("twl4030: I2C error %d reading PIH ISR\n", ret);
 		return IRQ_NONE;
@@ -501,7 +501,7 @@
 		} imr;
 
 		/* byte[0] gets overwritten as we write ... */
-		imr.word = cpu_to_le32(agent->imr << 8);
+		imr.word = cpu_to_le32(agent->imr);
 		agent->imr_change_pending = false;
 
 		/* write the whole mask ... simpler than subsetting it */
@@ -526,7 +526,7 @@
 		 * any processor on the other IRQ line, EDR registers are
 		 * shared.
 		 */
-		status = twl_i2c_read(sih->module, bytes + 1,
+		status = twl_i2c_read(sih->module, bytes,
 				sih->edr_offset, sih->bytes_edr);
 		if (status) {
 			pr_err("twl4030: %s, %s --> %d\n", __func__,
@@ -538,7 +538,7 @@
 		while (edge_change) {
 			int		i = fls(edge_change) - 1;
 			struct irq_data	*idata;
-			int		byte = 1 + (i >> 2);
+			int		byte = i >> 2;
 			int		off = (i & 0x3) * 2;
 			unsigned int	type;
 
diff --git a/drivers/mfd/twl4030-madc.c b/drivers/mfd/twl4030-madc.c
index a39dcf3..88ff9dc 100644
--- a/drivers/mfd/twl4030-madc.c
+++ b/drivers/mfd/twl4030-madc.c
@@ -173,7 +173,7 @@
 
 	volt = (raw_volt * TEMP_STEP_SIZE) / TEMP_PSR_R;
 	/* Getting and calculating the supply current in micro ampers */
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE, &val,
+	ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE, &val,
 		REG_BCICTL2);
 	if (ret < 0)
 		return ret;
@@ -196,7 +196,7 @@
 	int ret;
 	u8 val;
 
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE, &val,
+	ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE, &val,
 		TWL4030_BCI_BCICTL1);
 	if (ret)
 		return ret;
@@ -635,7 +635,7 @@
 	int ret;
 	u8 regval;
 
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+	ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE,
 			      &regval, TWL4030_BCI_BCICTL1);
 	if (ret) {
 		dev_err(madc->dev, "unable to read BCICTL1 reg 0x%X",
@@ -646,7 +646,7 @@
 		regval |= chan ? TWL4030_BCI_ITHEN : TWL4030_BCI_TYPEN;
 	else
 		regval &= chan ? ~TWL4030_BCI_ITHEN : ~TWL4030_BCI_TYPEN;
-	ret = twl_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE,
+	ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
 			       regval, TWL4030_BCI_BCICTL1);
 	if (ret) {
 		dev_err(madc->dev, "unable to write BCICTL1 reg 0x%X\n",
@@ -668,7 +668,7 @@
 	u8 regval;
 	int ret;
 
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+	ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE,
 			      &regval, TWL4030_MADC_CTRL1);
 	if (ret) {
 		dev_err(madc->dev, "unable to read madc ctrl1 reg 0x%X\n",
@@ -725,7 +725,7 @@
 	if (ret < 0)
 		goto err_current_generator;
 
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
+	ret = twl_i2c_read_u8(TWL_MODULE_MAIN_CHARGE,
 			      &regval, TWL4030_BCI_BCICTL1);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to read reg BCI CTL1 0x%X\n",
@@ -733,7 +733,7 @@
 		goto err_i2c;
 	}
 	regval |= TWL4030_BCI_MESBAT;
-	ret = twl_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE,
+	ret = twl_i2c_write_u8(TWL_MODULE_MAIN_CHARGE,
 			       regval, TWL4030_BCI_BCICTL1);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to write reg BCI Ctl1 0x%X\n",
diff --git a/drivers/mfd/twl4030-power.c b/drivers/mfd/twl4030-power.c
index a533206..4dae241 100644
--- a/drivers/mfd/twl4030-power.c
+++ b/drivers/mfd/twl4030-power.c
@@ -128,12 +128,10 @@
 {
 	int err;
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, address,
-				R_MEMORY_ADDRESS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, address, R_MEMORY_ADDRESS);
 	if (err)
 		goto out;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, byte,
-				R_MEMORY_DATA);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, byte, R_MEMORY_DATA);
 out:
 	return err;
 }
@@ -189,19 +187,16 @@
 	u8 data;
 
 	/* Set SLEEP to ACTIVE SEQ address for P3 */
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, address,
-				R_SEQ_ADD_S2A3);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, address, R_SEQ_ADD_S2A3);
 	if (err)
 		goto out;
 
 	/* P3 LVL_WAKEUP should be on LEVEL */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &data,
-				R_P3_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data, R_P3_SW_EVENTS);
 	if (err)
 		goto out;
 	data |= LVL_WAKEUP;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, data,
-				R_P3_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P3_SW_EVENTS);
 out:
 	if (err)
 		pr_err("TWL4030 wakeup sequence for P3 config error\n");
@@ -214,43 +209,38 @@
 	u8 data;
 
 	/* Set SLEEP to ACTIVE SEQ address for P1 and P2 */
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, address,
-				R_SEQ_ADD_S2A12);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, address, R_SEQ_ADD_S2A12);
 	if (err)
 		goto out;
 
 	/* P1/P2 LVL_WAKEUP should be on LEVEL */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &data,
-				R_P1_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data, R_P1_SW_EVENTS);
 	if (err)
 		goto out;
 
 	data |= LVL_WAKEUP;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, data,
-				R_P1_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P1_SW_EVENTS);
 	if (err)
 		goto out;
 
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &data,
-				R_P2_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data, R_P2_SW_EVENTS);
 	if (err)
 		goto out;
 
 	data |= LVL_WAKEUP;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, data,
-				R_P2_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data, R_P2_SW_EVENTS);
 	if (err)
 		goto out;
 
 	if (machine_is_omap_3430sdp() || machine_is_omap_ldp()) {
 		/* Disabling AC charger effect on sleep-active transitions */
-		err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &data,
-					R_CFG_P1_TRANSITION);
+		err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &data,
+				      R_CFG_P1_TRANSITION);
 		if (err)
 			goto out;
 		data &= ~(1<<1);
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, data ,
-					R_CFG_P1_TRANSITION);
+		err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, data,
+				       R_CFG_P1_TRANSITION);
 		if (err)
 			goto out;
 	}
@@ -267,8 +257,7 @@
 	int err;
 
 	/* Set ACTIVE to SLEEP SEQ address in T2 memory*/
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, address,
-				R_SEQ_ADD_A2S);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, address, R_SEQ_ADD_A2S);
 
 	if (err)
 		pr_err("TWL4030 sleep sequence config error\n");
@@ -282,42 +271,35 @@
 	u8 rd_data;
 
 	/* Set WARM RESET SEQ address for P1 */
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, address,
-				R_SEQ_ADD_WARM);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, address, R_SEQ_ADD_WARM);
 	if (err)
 		goto out;
 
 	/* P1/P2/P3 enable WARMRESET */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &rd_data,
-				R_P1_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &rd_data, R_P1_SW_EVENTS);
 	if (err)
 		goto out;
 
 	rd_data |= ENABLE_WARMRESET;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, rd_data,
-				R_P1_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P1_SW_EVENTS);
 	if (err)
 		goto out;
 
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &rd_data,
-				R_P2_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &rd_data, R_P2_SW_EVENTS);
 	if (err)
 		goto out;
 
 	rd_data |= ENABLE_WARMRESET;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, rd_data,
-				R_P2_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P2_SW_EVENTS);
 	if (err)
 		goto out;
 
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &rd_data,
-				R_P3_SW_EVENTS);
+	err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &rd_data, R_P3_SW_EVENTS);
 	if (err)
 		goto out;
 
 	rd_data |= ENABLE_WARMRESET;
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, rd_data,
-				R_P3_SW_EVENTS);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, rd_data, R_P3_SW_EVENTS);
 out:
 	if (err)
 		pr_err("TWL4030 warmreset seq config error\n");
@@ -341,7 +323,7 @@
 	rconfig_addr = res_config_addrs[rconfig->resource];
 
 	/* Set resource group */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &grp,
+	err = twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &grp,
 			      rconfig_addr + DEV_GRP_OFFSET);
 	if (err) {
 		pr_err("TWL4030 Resource %d group could not be read\n",
@@ -352,7 +334,7 @@
 	if (rconfig->devgroup != TWL4030_RESCONFIG_UNDEF) {
 		grp &= ~DEV_GRP_MASK;
 		grp |= rconfig->devgroup << DEV_GRP_SHIFT;
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
+		err = twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER,
 				       grp, rconfig_addr + DEV_GRP_OFFSET);
 		if (err < 0) {
 			pr_err("TWL4030 failed to program devgroup\n");
@@ -361,7 +343,7 @@
 	}
 
 	/* Set resource types */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &type,
+	err = twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &type,
 				rconfig_addr + TYPE_OFFSET);
 	if (err < 0) {
 		pr_err("TWL4030 Resource %d type could not be read\n",
@@ -379,7 +361,7 @@
 		type |= rconfig->type2 << TYPE2_SHIFT;
 	}
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
+	err = twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER,
 				type, rconfig_addr + TYPE_OFFSET);
 	if (err < 0) {
 		pr_err("TWL4030 failed to program resource type\n");
@@ -387,7 +369,7 @@
 	}
 
 	/* Set remap states */
-	err = twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &remap,
+	err = twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &remap,
 			      rconfig_addr + REMAP_OFFSET);
 	if (err < 0) {
 		pr_err("TWL4030 Resource %d remap could not be read\n",
@@ -405,7 +387,7 @@
 		remap |= rconfig->remap_sleep << SLEEP_STATE_SHIFT;
 	}
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
+	err = twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER,
 			       remap,
 			       rconfig_addr + REMAP_OFFSET);
 	if (err < 0) {
@@ -463,49 +445,47 @@
 {
 	int err = 0;
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG1,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err) {
 		pr_err("twl4030: unable to unlock PROTECT_KEY\n");
 		return err;
 	}
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG2,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err) {
 		pr_err("twl4030: unable to unlock PROTECT_KEY\n");
 		return err;
 	}
 
 	if (flags & TWL4030_WRST_SCRIPT) {
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, END_OF_SCRIPT,
-				R_SEQ_ADD_WARM);
+		err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT,
+				       R_SEQ_ADD_WARM);
 		if (err)
 			return err;
 	}
 	if (flags & TWL4030_WAKEUP12_SCRIPT) {
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, END_OF_SCRIPT,
-				R_SEQ_ADD_S2A12);
+		err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT,
+				       R_SEQ_ADD_S2A12);
 		if (err)
 			return err;
 	}
 	if (flags & TWL4030_WAKEUP3_SCRIPT) {
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, END_OF_SCRIPT,
-				R_SEQ_ADD_S2A3);
+		err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT,
+				       R_SEQ_ADD_S2A3);
 		if (err)
 			return err;
 	}
 	if (flags & TWL4030_SLEEP_SCRIPT) {
-		err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, END_OF_SCRIPT,
-				R_SEQ_ADD_A2S);
+		err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, END_OF_SCRIPT,
+				       R_SEQ_ADD_A2S);
 		if (err)
 			return err;
 	}
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err)
 		pr_err("TWL4030 Unable to relock registers\n");
 
@@ -521,7 +501,7 @@
 {
 	int err;
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, PWR_DEVOFF,
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, PWR_DEVOFF,
 			       TWL4030_PM_MASTER_P1_SW_EVENTS);
 	if (err)
 		pr_err("TWL4030 Unable to power off\n");
@@ -534,15 +514,13 @@
 	struct twl4030_resconfig *resconfig;
 	u8 val, address = twl4030_start_script_address;
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG1,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG1,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err)
 		goto unlock;
 
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER,
-			TWL4030_PM_MASTER_KEY_CFG2,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, TWL4030_PM_MASTER_KEY_CFG2,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err)
 		goto unlock;
 
@@ -567,14 +545,14 @@
 	/* Board has to be wired properly to use this feature */
 	if (twl4030_scripts->use_poweroff && !pm_power_off) {
 		/* Default for SEQ_OFFSYNC is set, lets ensure this */
-		err = twl_i2c_read_u8(TWL4030_MODULE_PM_MASTER, &val,
+		err = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &val,
 				      TWL4030_PM_MASTER_CFG_P123_TRANSITION);
 		if (err) {
 			pr_warning("TWL4030 Unable to read registers\n");
 
 		} else if (!(val & SEQ_OFFSYNC)) {
 			val |= SEQ_OFFSYNC;
-			err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, val,
+			err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, val,
 					TWL4030_PM_MASTER_CFG_P123_TRANSITION);
 			if (err) {
 				pr_err("TWL4030 Unable to setup SEQ_OFFSYNC\n");
@@ -586,8 +564,8 @@
 	}
 
 relock:
-	err = twl_i2c_write_u8(TWL4030_MODULE_PM_MASTER, 0,
-			TWL4030_PM_MASTER_PROTECT_KEY);
+	err = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, 0,
+			       TWL4030_PM_MASTER_PROTECT_KEY);
 	if (err)
 		pr_err("TWL4030 Unable to relock registers\n");
 	return;
diff --git a/drivers/mfd/twl6030-irq.c b/drivers/mfd/twl6030-irq.c
index b76902f..277a8db 100644
--- a/drivers/mfd/twl6030-irq.c
+++ b/drivers/mfd/twl6030-irq.c
@@ -355,7 +355,7 @@
 	static struct irq_chip  twl6030_irq_chip;
 	int			status = 0;
 	int			i;
-	u8			mask[4];
+	u8			mask[3];
 
 	nr_irqs = TWL6030_NR_IRQS;
 
@@ -370,9 +370,9 @@
 
 	irq_end = irq_base + nr_irqs;
 
+	mask[0] = 0xFF;
 	mask[1] = 0xFF;
 	mask[2] = 0xFF;
-	mask[3] = 0xFF;
 
 	/* mask all int lines */
 	twl_i2c_write(TWL_MODULE_PIH, &mask[0], REG_INT_MSK_LINE_A, 3);
diff --git a/drivers/mfd/twl6040-irq.c b/drivers/mfd/twl6040-irq.c
deleted file mode 100644
index 4b42543..0000000
--- a/drivers/mfd/twl6040-irq.c
+++ /dev/null
@@ -1,205 +0,0 @@
-/*
- * Interrupt controller support for TWL6040
- *
- * Author:     Misael Lopez Cruz <misael.lopez@ti.com>
- *
- * Copyright:   (C) 2011 Texas Instruments, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/err.h>
-#include <linux/irq.h>
-#include <linux/of.h>
-#include <linux/irqdomain.h>
-#include <linux/interrupt.h>
-#include <linux/mfd/core.h>
-#include <linux/mfd/twl6040.h>
-
-struct twl6040_irq_data {
-	int mask;
-	int status;
-};
-
-static struct twl6040_irq_data twl6040_irqs[] = {
-	{
-		.mask = TWL6040_THMSK,
-		.status = TWL6040_THINT,
-	},
-	{
-		.mask = TWL6040_PLUGMSK,
-		.status = TWL6040_PLUGINT | TWL6040_UNPLUGINT,
-	},
-	{
-		.mask = TWL6040_HOOKMSK,
-		.status = TWL6040_HOOKINT,
-	},
-	{
-		.mask = TWL6040_HFMSK,
-		.status = TWL6040_HFINT,
-	},
-	{
-		.mask = TWL6040_VIBMSK,
-		.status = TWL6040_VIBINT,
-	},
-	{
-		.mask = TWL6040_READYMSK,
-		.status = TWL6040_READYINT,
-	},
-};
-
-static inline
-struct twl6040_irq_data *irq_to_twl6040_irq(struct twl6040 *twl6040,
-					    int irq)
-{
-	return &twl6040_irqs[irq - twl6040->irq_base];
-}
-
-static void twl6040_irq_lock(struct irq_data *data)
-{
-	struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data);
-
-	mutex_lock(&twl6040->irq_mutex);
-}
-
-static void twl6040_irq_sync_unlock(struct irq_data *data)
-{
-	struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data);
-
-	/* write back to hardware any change in irq mask */
-	if (twl6040->irq_masks_cur != twl6040->irq_masks_cache) {
-		twl6040->irq_masks_cache = twl6040->irq_masks_cur;
-		twl6040_reg_write(twl6040, TWL6040_REG_INTMR,
-				  twl6040->irq_masks_cur);
-	}
-
-	mutex_unlock(&twl6040->irq_mutex);
-}
-
-static void twl6040_irq_enable(struct irq_data *data)
-{
-	struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data);
-	struct twl6040_irq_data *irq_data = irq_to_twl6040_irq(twl6040,
-							       data->irq);
-
-	twl6040->irq_masks_cur &= ~irq_data->mask;
-}
-
-static void twl6040_irq_disable(struct irq_data *data)
-{
-	struct twl6040 *twl6040 = irq_data_get_irq_chip_data(data);
-	struct twl6040_irq_data *irq_data = irq_to_twl6040_irq(twl6040,
-							       data->irq);
-
-	twl6040->irq_masks_cur |= irq_data->mask;
-}
-
-static struct irq_chip twl6040_irq_chip = {
-	.name			= "twl6040",
-	.irq_bus_lock		= twl6040_irq_lock,
-	.irq_bus_sync_unlock	= twl6040_irq_sync_unlock,
-	.irq_enable		= twl6040_irq_enable,
-	.irq_disable		= twl6040_irq_disable,
-};
-
-static irqreturn_t twl6040_irq_thread(int irq, void *data)
-{
-	struct twl6040 *twl6040 = data;
-	u8 intid;
-	int i;
-
-	intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID);
-
-	/* apply masking and report (backwards to handle READYINT first) */
-	for (i = ARRAY_SIZE(twl6040_irqs) - 1; i >= 0; i--) {
-		if (twl6040->irq_masks_cur & twl6040_irqs[i].mask)
-			intid &= ~twl6040_irqs[i].status;
-		if (intid & twl6040_irqs[i].status)
-			handle_nested_irq(twl6040->irq_base + i);
-	}
-
-	/* ack unmasked irqs */
-	twl6040_reg_write(twl6040, TWL6040_REG_INTID, intid);
-
-	return IRQ_HANDLED;
-}
-
-int twl6040_irq_init(struct twl6040 *twl6040)
-{
-	struct device_node *node = twl6040->dev->of_node;
-	int i, nr_irqs, irq_base, ret;
-	u8 val;
-
-	mutex_init(&twl6040->irq_mutex);
-
-	/* mask the individual interrupt sources */
-	twl6040->irq_masks_cur = TWL6040_ALLINT_MSK;
-	twl6040->irq_masks_cache = TWL6040_ALLINT_MSK;
-	twl6040_reg_write(twl6040, TWL6040_REG_INTMR, TWL6040_ALLINT_MSK);
-
-	nr_irqs = ARRAY_SIZE(twl6040_irqs);
-
-	irq_base = irq_alloc_descs(-1, 0, nr_irqs, 0);
-	if (IS_ERR_VALUE(irq_base)) {
-		dev_err(twl6040->dev, "Fail to allocate IRQ descs\n");
-		return irq_base;
-	}
-	twl6040->irq_base = irq_base;
-
-	irq_domain_add_legacy(node, ARRAY_SIZE(twl6040_irqs), irq_base, 0,
-			      &irq_domain_simple_ops, NULL);
-
-	/* Register them with genirq */
-	for (i = irq_base; i < irq_base + nr_irqs; i++) {
-		irq_set_chip_data(i, twl6040);
-		irq_set_chip_and_handler(i, &twl6040_irq_chip,
-					 handle_level_irq);
-		irq_set_nested_thread(i, 1);
-
-		/* ARM needs us to explicitly flag the IRQ as valid
-		 * and will set them noprobe when we do so. */
-#ifdef CONFIG_ARM
-		set_irq_flags(i, IRQF_VALID);
-#else
-		irq_set_noprobe(i);
-#endif
-	}
-
-	ret = request_threaded_irq(twl6040->irq, NULL, twl6040_irq_thread,
-				   IRQF_ONESHOT, "twl6040", twl6040);
-	if (ret) {
-		dev_err(twl6040->dev, "failed to request IRQ %d: %d\n",
-			twl6040->irq, ret);
-		return ret;
-	}
-
-	/* reset interrupts */
-	val = twl6040_reg_read(twl6040, TWL6040_REG_INTID);
-
-	/* interrupts cleared on write */
-	twl6040_clear_bits(twl6040, TWL6040_REG_ACCCTL, TWL6040_INTCLRMODE);
-
-	return 0;
-}
-EXPORT_SYMBOL(twl6040_irq_init);
-
-void twl6040_irq_exit(struct twl6040 *twl6040)
-{
-	free_irq(twl6040->irq, twl6040);
-}
-EXPORT_SYMBOL(twl6040_irq_exit);
diff --git a/drivers/mfd/twl6040-core.c b/drivers/mfd/twl6040.c
similarity index 84%
rename from drivers/mfd/twl6040-core.c
rename to drivers/mfd/twl6040.c
index 3f2a1cf..583be76 100644
--- a/drivers/mfd/twl6040-core.c
+++ b/drivers/mfd/twl6040.c
@@ -37,7 +37,6 @@
 #include <linux/delay.h>
 #include <linux/i2c.h>
 #include <linux/regmap.h>
-#include <linux/err.h>
 #include <linux/mfd/core.h>
 #include <linux/mfd/twl6040.h>
 #include <linux/regulator/consumer.h>
@@ -104,7 +103,7 @@
 EXPORT_SYMBOL(twl6040_clear_bits);
 
 /* twl6040 codec manual power-up sequence */
-static int twl6040_power_up(struct twl6040 *twl6040)
+static int twl6040_power_up_manual(struct twl6040 *twl6040)
 {
 	u8 ldoctl, ncpctl, lppllctl;
 	int ret;
@@ -158,11 +157,12 @@
 	ldoctl &= ~(TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA);
 	twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl);
 
+	dev_err(twl6040->dev, "manual power-up failed\n");
 	return ret;
 }
 
 /* twl6040 manual power-down sequence */
-static void twl6040_power_down(struct twl6040 *twl6040)
+static void twl6040_power_down_manual(struct twl6040 *twl6040)
 {
 	u8 ncpctl, ldoctl, lppllctl;
 
@@ -192,45 +192,48 @@
 	twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl);
 }
 
-static irqreturn_t twl6040_naudint_handler(int irq, void *data)
+static irqreturn_t twl6040_readyint_handler(int irq, void *data)
 {
 	struct twl6040 *twl6040 = data;
-	u8 intid, status;
 
-	intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID);
+	complete(&twl6040->ready);
 
-	if (intid & TWL6040_READYINT)
-		complete(&twl6040->ready);
+	return IRQ_HANDLED;
+}
 
-	if (intid & TWL6040_THINT) {
-		status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS);
-		if (status & TWL6040_TSHUTDET) {
-			dev_warn(twl6040->dev,
-				 "Thermal shutdown, powering-off");
-			twl6040_power(twl6040, 0);
-		} else {
-			dev_warn(twl6040->dev,
-				 "Leaving thermal shutdown, powering-on");
-			twl6040_power(twl6040, 1);
-		}
+static irqreturn_t twl6040_thint_handler(int irq, void *data)
+{
+	struct twl6040 *twl6040 = data;
+	u8 status;
+
+	status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS);
+	if (status & TWL6040_TSHUTDET) {
+		dev_warn(twl6040->dev, "Thermal shutdown, powering-off");
+		twl6040_power(twl6040, 0);
+	} else {
+		dev_warn(twl6040->dev, "Leaving thermal shutdown, powering-on");
+		twl6040_power(twl6040, 1);
 	}
 
 	return IRQ_HANDLED;
 }
 
-static int twl6040_power_up_completion(struct twl6040 *twl6040,
-				       int naudint)
+static int twl6040_power_up_automatic(struct twl6040 *twl6040)
 {
 	int time_left;
-	u8 intid;
+
+	gpio_set_value(twl6040->audpwron, 1);
 
 	time_left = wait_for_completion_timeout(&twl6040->ready,
 						msecs_to_jiffies(144));
 	if (!time_left) {
+		u8 intid;
+
+		dev_warn(twl6040->dev, "timeout waiting for READYINT\n");
 		intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID);
 		if (!(intid & TWL6040_READYINT)) {
-			dev_err(twl6040->dev,
-				"timeout waiting for READYINT\n");
+			dev_err(twl6040->dev, "automatic power-up failed\n");
+			gpio_set_value(twl6040->audpwron, 0);
 			return -ETIMEDOUT;
 		}
 	}
@@ -240,8 +243,6 @@
 
 int twl6040_power(struct twl6040 *twl6040, int on)
 {
-	int audpwron = twl6040->audpwron;
-	int naudint = twl6040->irq;
 	int ret = 0;
 
 	mutex_lock(&twl6040->mutex);
@@ -251,23 +252,17 @@
 		if (twl6040->power_count++)
 			goto out;
 
-		if (gpio_is_valid(audpwron)) {
-			/* use AUDPWRON line */
-			gpio_set_value(audpwron, 1);
-			/* wait for power-up completion */
-			ret = twl6040_power_up_completion(twl6040, naudint);
+		if (gpio_is_valid(twl6040->audpwron)) {
+			/* use automatic power-up sequence */
+			ret = twl6040_power_up_automatic(twl6040);
 			if (ret) {
-				dev_err(twl6040->dev,
-					"automatic power-down failed\n");
 				twl6040->power_count = 0;
 				goto out;
 			}
 		} else {
 			/* use manual power-up sequence */
-			ret = twl6040_power_up(twl6040);
+			ret = twl6040_power_up_manual(twl6040);
 			if (ret) {
-				dev_err(twl6040->dev,
-					"manual power-up failed\n");
 				twl6040->power_count = 0;
 				goto out;
 			}
@@ -288,15 +283,15 @@
 		if (--twl6040->power_count)
 			goto out;
 
-		if (gpio_is_valid(audpwron)) {
+		if (gpio_is_valid(twl6040->audpwron)) {
 			/* use AUDPWRON line */
-			gpio_set_value(audpwron, 0);
+			gpio_set_value(twl6040->audpwron, 0);
 
 			/* power-down sequence latency */
 			usleep_range(500, 700);
 		} else {
 			/* use manual power-down sequence */
-			twl6040_power_down(twl6040);
+			twl6040_power_down_manual(twl6040);
 		}
 		twl6040->sysclk = 0;
 		twl6040->mclk = 0;
@@ -503,6 +498,25 @@
 	.readable_reg = twl6040_readable_reg,
 };
 
+static const struct regmap_irq twl6040_irqs[] = {
+	{ .reg_offset = 0, .mask = TWL6040_THINT, },
+	{ .reg_offset = 0, .mask = TWL6040_PLUGINT | TWL6040_UNPLUGINT, },
+	{ .reg_offset = 0, .mask = TWL6040_HOOKINT, },
+	{ .reg_offset = 0, .mask = TWL6040_HFINT, },
+	{ .reg_offset = 0, .mask = TWL6040_VIBINT, },
+	{ .reg_offset = 0, .mask = TWL6040_READYINT, },
+};
+
+static struct regmap_irq_chip twl6040_irq_chip = {
+	.name = "twl6040",
+	.irqs = twl6040_irqs,
+	.num_irqs = ARRAY_SIZE(twl6040_irqs),
+
+	.num_regs = 1,
+	.status_base = TWL6040_REG_INTID,
+	.mask_base = TWL6040_REG_INTMR,
+};
+
 static int __devinit twl6040_probe(struct i2c_client *client,
 				     const struct i2c_device_id *id)
 {
@@ -578,18 +592,31 @@
 			goto gpio_err;
 	}
 
-	/* codec interrupt */
-	ret = twl6040_irq_init(twl6040);
-	if (ret)
+	ret = regmap_add_irq_chip(twl6040->regmap, twl6040->irq,
+			IRQF_ONESHOT, 0, &twl6040_irq_chip,
+			&twl6040->irq_data);
+	if (ret < 0)
 		goto irq_init_err;
 
-	ret = request_threaded_irq(twl6040->irq_base + TWL6040_IRQ_READY,
-				   NULL, twl6040_naudint_handler, IRQF_ONESHOT,
+	twl6040->irq_ready = regmap_irq_get_virq(twl6040->irq_data,
+					       TWL6040_IRQ_READY);
+	twl6040->irq_th = regmap_irq_get_virq(twl6040->irq_data,
+					       TWL6040_IRQ_TH);
+
+	ret = request_threaded_irq(twl6040->irq_ready, NULL,
+				   twl6040_readyint_handler, IRQF_ONESHOT,
 				   "twl6040_irq_ready", twl6040);
 	if (ret) {
-		dev_err(twl6040->dev, "READY IRQ request failed: %d\n",
-			ret);
-		goto irq_err;
+		dev_err(twl6040->dev, "READY IRQ request failed: %d\n", ret);
+		goto readyirq_err;
+	}
+
+	ret = request_threaded_irq(twl6040->irq_th, NULL,
+				   twl6040_thint_handler, IRQF_ONESHOT,
+				   "twl6040_irq_th", twl6040);
+	if (ret) {
+		dev_err(twl6040->dev, "Thermal IRQ request failed: %d\n", ret);
+		goto thirq_err;
 	}
 
 	/* dual-access registers controlled by I2C only */
@@ -601,7 +628,7 @@
 	 * The ASoC codec can work without pdata, pass the platform_data only if
 	 * it has been provided.
 	 */
-	irq = twl6040->irq_base + TWL6040_IRQ_PLUG;
+	irq = regmap_irq_get_virq(twl6040->irq_data, TWL6040_IRQ_PLUG);
 	cell = &twl6040->cells[children];
 	cell->name = "twl6040-codec";
 	twl6040_codec_rsrc[0].start = irq;
@@ -615,7 +642,7 @@
 	children++;
 
 	if (twl6040_has_vibra(pdata, node)) {
-		irq = twl6040->irq_base + TWL6040_IRQ_VIB;
+		irq = regmap_irq_get_virq(twl6040->irq_data, TWL6040_IRQ_VIB);
 
 		cell = &twl6040->cells[children];
 		cell->name = "twl6040-vibra";
@@ -654,9 +681,11 @@
 	return 0;
 
 mfd_err:
-	free_irq(twl6040->irq_base + TWL6040_IRQ_READY, twl6040);
-irq_err:
-	twl6040_irq_exit(twl6040);
+	free_irq(twl6040->irq_th, twl6040);
+thirq_err:
+	free_irq(twl6040->irq_ready, twl6040);
+readyirq_err:
+	regmap_del_irq_chip(twl6040->irq, twl6040->irq_data);
 irq_init_err:
 	if (gpio_is_valid(twl6040->audpwron))
 		gpio_free(twl6040->audpwron);
@@ -680,8 +709,9 @@
 	if (gpio_is_valid(twl6040->audpwron))
 		gpio_free(twl6040->audpwron);
 
-	free_irq(twl6040->irq_base + TWL6040_IRQ_READY, twl6040);
-	twl6040_irq_exit(twl6040);
+	free_irq(twl6040->irq_ready, twl6040);
+	free_irq(twl6040->irq_th, twl6040);
+	regmap_del_irq_chip(twl6040->irq, twl6040->irq_data);
 
 	mfd_remove_devices(&client->dev);
 	i2c_set_clientdata(client, NULL);
diff --git a/drivers/mfd/viperboard.c b/drivers/mfd/viperboard.c
new file mode 100644
index 0000000..af2a670
--- /dev/null
+++ b/drivers/mfd/viperboard.c
@@ -0,0 +1,137 @@
+/*
+ *  Nano River Technologies viperboard driver
+ *
+ *  This is the core driver for the viperboard. There are cell drivers
+ *  available for I2C, ADC and both GPIOs. SPI is not yet supported.
+ *  The drivers do not support all features the board exposes. See user
+ *  manual of the viperboard.
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/mutex.h>
+
+#include <linux/mfd/core.h>
+#include <linux/mfd/viperboard.h>
+
+#include <linux/usb.h>
+
+
+static const struct usb_device_id vprbrd_table[] = {
+	{ USB_DEVICE(0x2058, 0x1005) },   /* Nano River Technologies */
+	{ }                               /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, vprbrd_table);
+
+static struct mfd_cell vprbrd_devs[] = {
+	{
+		.name = "viperboard-gpio",
+	},
+	{
+		.name = "viperboard-i2c",
+	},
+	{
+		.name = "viperboard-adc",
+	},
+};
+
+static int vprbrd_probe(struct usb_interface *interface,
+			      const struct usb_device_id *id)
+{
+	struct vprbrd *vb;
+
+	u16 version = 0;
+	int pipe, ret;
+
+	/* allocate memory for our device state and initialize it */
+	vb = kzalloc(sizeof(*vb), GFP_KERNEL);
+	if (vb == NULL) {
+		dev_err(&interface->dev, "Out of memory\n");
+		return -ENOMEM;
+	}
+
+	mutex_init(&vb->lock);
+
+	vb->usb_dev = usb_get_dev(interface_to_usbdev(interface));
+
+	/* save our data pointer in this interface device */
+	usb_set_intfdata(interface, vb);
+	dev_set_drvdata(&vb->pdev.dev, vb);
+
+	/* get version information, major first, minor then */
+	pipe = usb_rcvctrlpipe(vb->usb_dev, 0);
+	ret = usb_control_msg(vb->usb_dev, pipe, VPRBRD_USB_REQUEST_MAJOR,
+		VPRBRD_USB_TYPE_IN, 0x0000, 0x0000, vb->buf, 1,
+		VPRBRD_USB_TIMEOUT_MS);
+	if (ret == 1)
+		version = vb->buf[0];
+
+	ret = usb_control_msg(vb->usb_dev, pipe, VPRBRD_USB_REQUEST_MINOR,
+		VPRBRD_USB_TYPE_IN, 0x0000, 0x0000, vb->buf, 1,
+		VPRBRD_USB_TIMEOUT_MS);
+	if (ret == 1) {
+		version <<= 8;
+		version = version | vb->buf[0];
+	}
+
+	dev_info(&interface->dev,
+		 "version %x.%02x found at bus %03d address %03d\n",
+		 version >> 8, version & 0xff,
+		 vb->usb_dev->bus->busnum, vb->usb_dev->devnum);
+
+	ret = mfd_add_devices(&interface->dev, -1, vprbrd_devs,
+				ARRAY_SIZE(vprbrd_devs), NULL, 0, NULL);
+	if (ret != 0) {
+		dev_err(&interface->dev, "Failed to add mfd devices to core.");
+		goto error;
+	}
+
+	return 0;
+
+error:
+	if (vb) {
+		usb_put_dev(vb->usb_dev);
+		kfree(vb);
+	}
+
+	return ret;
+}
+
+static void vprbrd_disconnect(struct usb_interface *interface)
+{
+	struct vprbrd *vb = usb_get_intfdata(interface);
+
+	mfd_remove_devices(&interface->dev);
+	usb_set_intfdata(interface, NULL);
+	usb_put_dev(vb->usb_dev);
+	kfree(vb);
+
+	dev_dbg(&interface->dev, "disconnected\n");
+}
+
+static struct usb_driver vprbrd_driver = {
+	.name		= "viperboard",
+	.probe		= vprbrd_probe,
+	.disconnect	= vprbrd_disconnect,
+	.id_table	= vprbrd_table,
+};
+
+module_usb_driver(vprbrd_driver);
+
+MODULE_DESCRIPTION("Nano River Technologies viperboard mfd core driver");
+MODULE_AUTHOR("Lars Poeschel <poeschel@lemonage.de>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mfd/wm5102-tables.c b/drivers/mfd/wm5102-tables.c
index 3141c4a..088872a 100644
--- a/drivers/mfd/wm5102-tables.c
+++ b/drivers/mfd/wm5102-tables.c
@@ -56,6 +56,18 @@
 	{ 0x80, 0x0000 },
 };
 
+static const struct reg_default wm5102_revb_patch[] = {
+	{ 0x80, 0x0003 },
+	{ 0x081, 0xE022 },
+	{ 0x410, 0x6080 },
+	{ 0x418, 0x6080 },
+	{ 0x420, 0x6080 },
+	{ 0x428, 0xC000 },
+	{ 0x441, 0x8014 },
+	{ 0x458, 0x000b },
+	{ 0x80, 0x0000 },
+};
+
 /* We use a function so we can use ARRAY_SIZE() */
 int wm5102_patch(struct arizona *arizona)
 {
@@ -65,7 +77,9 @@
 					     wm5102_reva_patch,
 					     ARRAY_SIZE(wm5102_reva_patch));
 	default:
-		return 0;
+		return regmap_register_patch(arizona->regmap,
+					     wm5102_revb_patch,
+					     ARRAY_SIZE(wm5102_revb_patch));
 	}
 }
 
@@ -291,6 +305,7 @@
 	{ 0x000001AA, 0x0004 },   /* R426   - FLL2 GPIO Clock */ 
 	{ 0x00000200, 0x0006 },   /* R512   - Mic Charge Pump 1 */ 
 	{ 0x00000210, 0x00D4 },   /* R528   - LDO1 Control 1 */ 
+	{ 0x00000212, 0x0001 },   /* R530   - LDO1 Control 2 */
 	{ 0x00000213, 0x0344 },   /* R531   - LDO2 Control 1 */ 
 	{ 0x00000218, 0x01A6 },   /* R536   - Mic Bias Ctrl 1 */ 
 	{ 0x00000219, 0x01A6 },   /* R537   - Mic Bias Ctrl 2 */ 
@@ -1056,6 +1071,7 @@
 	case ARIZONA_FLL1_CONTROL_5:
 	case ARIZONA_FLL1_CONTROL_6:
 	case ARIZONA_FLL1_LOOP_FILTER_TEST_1:
+	case ARIZONA_FLL1_NCO_TEST_0:
 	case ARIZONA_FLL1_SYNCHRONISER_1:
 	case ARIZONA_FLL1_SYNCHRONISER_2:
 	case ARIZONA_FLL1_SYNCHRONISER_3:
@@ -1071,6 +1087,7 @@
 	case ARIZONA_FLL2_CONTROL_5:
 	case ARIZONA_FLL2_CONTROL_6:
 	case ARIZONA_FLL2_LOOP_FILTER_TEST_1:
+	case ARIZONA_FLL2_NCO_TEST_0:
 	case ARIZONA_FLL2_SYNCHRONISER_1:
 	case ARIZONA_FLL2_SYNCHRONISER_2:
 	case ARIZONA_FLL2_SYNCHRONISER_3:
@@ -1805,6 +1822,7 @@
 	case ARIZONA_DSP1_CLOCKING_1:
 	case ARIZONA_DSP1_STATUS_1:
 	case ARIZONA_DSP1_STATUS_2:
+	case ARIZONA_DSP1_STATUS_3:
 		return true;
 	default:
 		return false;
@@ -1813,15 +1831,23 @@
 
 static bool wm5102_volatile_register(struct device *dev, unsigned int reg)
 {
+	if (reg > 0xffff)
+		return true;
+
 	switch (reg) {
 	case ARIZONA_SOFTWARE_RESET:
 	case ARIZONA_DEVICE_REVISION:
 	case ARIZONA_OUTPUT_STATUS_1:
+	case ARIZONA_RAW_OUTPUT_STATUS_1:
+	case ARIZONA_SLIMBUS_RX_PORT_STATUS:
+	case ARIZONA_SLIMBUS_TX_PORT_STATUS:
 	case ARIZONA_SAMPLE_RATE_1_STATUS:
 	case ARIZONA_SAMPLE_RATE_2_STATUS:
 	case ARIZONA_SAMPLE_RATE_3_STATUS:
 	case ARIZONA_HAPTICS_STATUS:
 	case ARIZONA_ASYNC_SAMPLE_RATE_1_STATUS:
+	case ARIZONA_FLL1_NCO_TEST_0:
+	case ARIZONA_FLL2_NCO_TEST_0:
 	case ARIZONA_FX_CTRL2:
 	case ARIZONA_INTERRUPT_STATUS_1:
 	case ARIZONA_INTERRUPT_STATUS_2:
@@ -1847,6 +1873,7 @@
 	case ARIZONA_AOD_IRQ_RAW_STATUS:
 	case ARIZONA_DSP1_STATUS_1:
 	case ARIZONA_DSP1_STATUS_2:
+	case ARIZONA_DSP1_STATUS_3:
 	case ARIZONA_HEADPHONE_DETECT_2:
 	case ARIZONA_MIC_DETECT_3:
 		return true;
@@ -1855,12 +1882,14 @@
 	}
 }
 
+#define WM5102_MAX_REGISTER 0x1a8fff
+
 const struct regmap_config wm5102_spi_regmap = {
 	.reg_bits = 32,
 	.pad_bits = 16,
 	.val_bits = 16,
 
-	.max_register = ARIZONA_DSP1_STATUS_2,
+	.max_register = WM5102_MAX_REGISTER,
 	.readable_reg = wm5102_readable_register,
 	.volatile_reg = wm5102_volatile_register,
 
@@ -1874,7 +1903,7 @@
 	.reg_bits = 32,
 	.val_bits = 16,
 
-	.max_register = ARIZONA_DSP1_STATUS_2,
+	.max_register = WM5102_MAX_REGISTER,
 	.readable_reg = wm5102_readable_register,
 	.volatile_reg = wm5102_volatile_register,
 
diff --git a/drivers/mfd/wm8994-core.c b/drivers/mfd/wm8994-core.c
index bcb226f..57c488d 100644
--- a/drivers/mfd/wm8994-core.c
+++ b/drivers/mfd/wm8994-core.c
@@ -535,11 +535,10 @@
 			break;
 		case 2:
 		case 3:
+		default:
 			regmap_patch = wm8994_revc_patch;
 			patch_regs = ARRAY_SIZE(wm8994_revc_patch);
 			break;
-		default:
-			break;
 		}
 		break;
 
@@ -558,17 +557,9 @@
 		/* Revision C did not change the relevant layer */
 		if (wm8994->revision > 1)
 			wm8994->revision++;
-		switch (wm8994->revision) {
-		case 0:
-		case 1:
-		case 2:
-		case 3:
-			regmap_patch = wm1811_reva_patch;
-			patch_regs = ARRAY_SIZE(wm1811_reva_patch);
-			break;
-		default:
-			break;
-		}
+
+		regmap_patch = wm1811_reva_patch;
+		patch_regs = ARRAY_SIZE(wm1811_reva_patch);
 		break;
 
 	default:
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index b648058..e4e218c 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -49,6 +49,8 @@
 
 obj-$(CONFIG_MMC_REALTEK_PCI)	+= rtsx_pci_sdmmc.o
 
+obj-$(CONFIG_MMC_REALTEK_PCI)	+= rtsx_pci_sdmmc.o
+
 obj-$(CONFIG_MMC_SDHCI_PLTFM)		+= sdhci-pltfm.o
 obj-$(CONFIG_MMC_SDHCI_CNS3XXX)		+= sdhci-cns3xxx.o
 obj-$(CONFIG_MMC_SDHCI_ESDHC_IMX)	+= sdhci-esdhc-imx.o
diff --git a/drivers/mmc/host/rtsx_pci_sdmmc.c b/drivers/mmc/host/rtsx_pci_sdmmc.c
index 12eff6f..571915d 100644
--- a/drivers/mmc/host/rtsx_pci_sdmmc.c
+++ b/drivers/mmc/host/rtsx_pci_sdmmc.c
@@ -21,6 +21,7 @@
  */
 
 #include <linux/module.h>
+#include <linux/slab.h>
 #include <linux/highmem.h>
 #include <linux/delay.h>
 #include <linux/platform_device.h>
@@ -382,8 +383,6 @@
 			0xFF, (u8)data->blocks);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD_BLOCK_CNT_H,
 			0xFF, (u8)(data->blocks >> 8));
-	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD,
-			CARD_DATA_SOURCE, 0x01, RING_BUFFER);
 
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, IRQSTAT0,
 			DMA_DONE_INT, DMA_DONE_INT);
@@ -407,6 +406,7 @@
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, CARD_DATA_SOURCE,
 			0x01, RING_BUFFER);
 
+	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD_CFG2, 0xFF, cfg2);
 	rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, SD_TRANSFER, 0xFF,
 			trans_mode | SD_TRANSFER_START);
 	rtsx_pci_add_cmd(pcr, CHECK_REG_CMD, SD_TRANSFER,
diff --git a/drivers/power/da9052-battery.c b/drivers/power/da9052-battery.c
index bb0df89..3c5c2e4 100644
--- a/drivers/power/da9052-battery.c
+++ b/drivers/power/da9052-battery.c
@@ -440,8 +440,10 @@
 static irqreturn_t da9052_bat_irq(int irq, void *data)
 {
 	struct da9052_battery *bat = data;
+	int virq;
 
-	irq -= bat->da9052->irq_base;
+	virq = regmap_irq_get_virq(bat->da9052->irq_data, irq);
+	irq -= virq;
 
 	if (irq == DA9052_IRQ_CHGEND)
 		bat->status = POWER_SUPPLY_STATUS_FULL;
@@ -567,7 +569,7 @@
 	.get_property	= da9052_bat_get_property,
 };
 
-static const char *const da9052_bat_irqs[] = {
+static char *da9052_bat_irqs[] = {
 	"BATT TEMP",
 	"DCIN DET",
 	"DCIN REM",
@@ -576,12 +578,20 @@
 	"CHG END",
 };
 
+static int da9052_bat_irq_bits[] = {
+	DA9052_IRQ_TBAT,
+	DA9052_IRQ_DCIN,
+	DA9052_IRQ_DCINREM,
+	DA9052_IRQ_VBUS,
+	DA9052_IRQ_VBUSREM,
+	DA9052_IRQ_CHGEND,
+};
+
 static s32 da9052_bat_probe(struct platform_device *pdev)
 {
 	struct da9052_pdata *pdata;
 	struct da9052_battery *bat;
 	int ret;
-	int irq;
 	int i;
 
 	bat = kzalloc(sizeof(struct da9052_battery), GFP_KERNEL);
@@ -602,15 +612,14 @@
 		bat->psy.use_for_apm = 1;
 
 	for (i = 0; i < ARRAY_SIZE(da9052_bat_irqs); i++) {
-		irq = platform_get_irq_byname(pdev, da9052_bat_irqs[i]);
-		ret = request_threaded_irq(bat->da9052->irq_base + irq,
-					   NULL, da9052_bat_irq,
-					   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-					   da9052_bat_irqs[i], bat);
+		ret = da9052_request_irq(bat->da9052,
+				da9052_bat_irq_bits[i], da9052_bat_irqs[i],
+				da9052_bat_irq, bat);
+
 		if (ret != 0) {
 			dev_err(bat->da9052->dev,
-				"DA9052 failed to request %s IRQ %d: %d\n",
-				da9052_bat_irqs[i], irq, ret);
+				"DA9052 failed to request %s IRQ: %d\n",
+				da9052_bat_irqs[i], ret);
 			goto err;
 		}
 	}
@@ -623,23 +632,20 @@
 	return 0;
 
 err:
-	while (--i >= 0) {
-		irq = platform_get_irq_byname(pdev, da9052_bat_irqs[i]);
-		free_irq(bat->da9052->irq_base + irq, bat);
-	}
+	while (--i >= 0)
+		da9052_free_irq(bat->da9052, da9052_bat_irq_bits[i], bat);
+
 	kfree(bat);
 	return ret;
 }
 static int da9052_bat_remove(struct platform_device *pdev)
 {
 	int i;
-	int irq;
 	struct da9052_battery *bat = platform_get_drvdata(pdev);
 
-	for (i = 0; i < ARRAY_SIZE(da9052_bat_irqs); i++) {
-		irq = platform_get_irq_byname(pdev, da9052_bat_irqs[i]);
-		free_irq(bat->da9052->irq_base + irq, bat);
-	}
+	for (i = 0; i < ARRAY_SIZE(da9052_bat_irqs); i++)
+		da9052_free_irq(bat->da9052, da9052_bat_irq_bits[i], bat);
+
 	power_supply_unregister(&bat->psy);
 	kfree(bat);
 
diff --git a/drivers/rtc/rtc-twl.c b/drivers/rtc/rtc-twl.c
index 9277d94..8b7464c 100644
--- a/drivers/rtc/rtc-twl.c
+++ b/drivers/rtc/rtc-twl.c
@@ -233,7 +233,7 @@
  */
 static int twl_rtc_read_time(struct device *dev, struct rtc_time *tm)
 {
-	unsigned char rtc_data[ALL_TIME_REGS + 1];
+	unsigned char rtc_data[ALL_TIME_REGS];
 	int ret;
 	u8 save_control;
 	u8 rtc_control;
@@ -300,15 +300,15 @@
 static int twl_rtc_set_time(struct device *dev, struct rtc_time *tm)
 {
 	unsigned char save_control;
-	unsigned char rtc_data[ALL_TIME_REGS + 1];
+	unsigned char rtc_data[ALL_TIME_REGS];
 	int ret;
 
-	rtc_data[1] = bin2bcd(tm->tm_sec);
-	rtc_data[2] = bin2bcd(tm->tm_min);
-	rtc_data[3] = bin2bcd(tm->tm_hour);
-	rtc_data[4] = bin2bcd(tm->tm_mday);
-	rtc_data[5] = bin2bcd(tm->tm_mon + 1);
-	rtc_data[6] = bin2bcd(tm->tm_year - 100);
+	rtc_data[0] = bin2bcd(tm->tm_sec);
+	rtc_data[1] = bin2bcd(tm->tm_min);
+	rtc_data[2] = bin2bcd(tm->tm_hour);
+	rtc_data[3] = bin2bcd(tm->tm_mday);
+	rtc_data[4] = bin2bcd(tm->tm_mon + 1);
+	rtc_data[5] = bin2bcd(tm->tm_year - 100);
 
 	/* Stop RTC while updating the TC registers */
 	ret = twl_rtc_read_u8(&save_control, REG_RTC_CTRL_REG);
@@ -341,7 +341,7 @@
  */
 static int twl_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm)
 {
-	unsigned char rtc_data[ALL_TIME_REGS + 1];
+	unsigned char rtc_data[ALL_TIME_REGS];
 	int ret;
 
 	ret = twl_i2c_read(TWL_MODULE_RTC, rtc_data,
@@ -368,19 +368,19 @@
 
 static int twl_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm)
 {
-	unsigned char alarm_data[ALL_TIME_REGS + 1];
+	unsigned char alarm_data[ALL_TIME_REGS];
 	int ret;
 
 	ret = twl_rtc_alarm_irq_enable(dev, 0);
 	if (ret)
 		goto out;
 
-	alarm_data[1] = bin2bcd(alm->time.tm_sec);
-	alarm_data[2] = bin2bcd(alm->time.tm_min);
-	alarm_data[3] = bin2bcd(alm->time.tm_hour);
-	alarm_data[4] = bin2bcd(alm->time.tm_mday);
-	alarm_data[5] = bin2bcd(alm->time.tm_mon + 1);
-	alarm_data[6] = bin2bcd(alm->time.tm_year - 100);
+	alarm_data[0] = bin2bcd(alm->time.tm_sec);
+	alarm_data[1] = bin2bcd(alm->time.tm_min);
+	alarm_data[2] = bin2bcd(alm->time.tm_hour);
+	alarm_data[3] = bin2bcd(alm->time.tm_mday);
+	alarm_data[4] = bin2bcd(alm->time.tm_mon + 1);
+	alarm_data[5] = bin2bcd(alm->time.tm_year - 100);
 
 	/* update all the alarm registers in one shot */
 	ret = twl_i2c_write(TWL_MODULE_RTC, alarm_data,
diff --git a/include/linux/i2c/twl.h b/include/linux/i2c/twl.h
index 9a5e284..1ff54b1 100644
--- a/include/linux/i2c/twl.h
+++ b/include/linux/i2c/twl.h
@@ -39,52 +39,51 @@
  * address each module uses within a given i2c slave.
  */
 
-/* Slave 0 (i2c address 0x48) */
-#define TWL4030_MODULE_USB		0x00
+enum twl4030_module_ids {
+	TWL4030_MODULE_USB = 0,		/* Slave 0 (i2c address 0x48) */
+	TWL4030_MODULE_AUDIO_VOICE,	/* Slave 1 (i2c address 0x49) */
+	TWL4030_MODULE_GPIO,
+	TWL4030_MODULE_INTBR,
+	TWL4030_MODULE_PIH,
 
-/* Slave 1 (i2c address 0x49) */
-#define TWL4030_MODULE_AUDIO_VOICE	0x01
-#define TWL4030_MODULE_GPIO		0x02
-#define TWL4030_MODULE_INTBR		0x03
-#define TWL4030_MODULE_PIH		0x04
-#define TWL4030_MODULE_TEST		0x05
+	TWL4030_MODULE_TEST,
+	TWL4030_MODULE_KEYPAD,		/* Slave 2 (i2c address 0x4a) */
+	TWL4030_MODULE_MADC,
+	TWL4030_MODULE_INTERRUPTS,
+	TWL4030_MODULE_LED,
 
-/* Slave 2 (i2c address 0x4a) */
-#define TWL4030_MODULE_KEYPAD		0x06
-#define TWL4030_MODULE_MADC		0x07
-#define TWL4030_MODULE_INTERRUPTS	0x08
-#define TWL4030_MODULE_LED		0x09
-#define TWL4030_MODULE_MAIN_CHARGE	0x0A
-#define TWL4030_MODULE_PRECHARGE	0x0B
-#define TWL4030_MODULE_PWM0		0x0C
-#define TWL4030_MODULE_PWM1		0x0D
-#define TWL4030_MODULE_PWMA		0x0E
-#define TWL4030_MODULE_PWMB		0x0F
+	TWL4030_MODULE_MAIN_CHARGE,
+	TWL4030_MODULE_PRECHARGE,
+	TWL4030_MODULE_PWM0,
+	TWL4030_MODULE_PWM1,
+	TWL4030_MODULE_PWMA,
 
-#define TWL5031_MODULE_ACCESSORY	0x10
-#define TWL5031_MODULE_INTERRUPTS	0x11
+	TWL4030_MODULE_PWMB,
+	TWL5031_MODULE_ACCESSORY,
+	TWL5031_MODULE_INTERRUPTS,
+	TWL4030_MODULE_BACKUP,		/* Slave 3 (i2c address 0x4b) */
+	TWL4030_MODULE_INT,
 
-/* Slave 3 (i2c address 0x4b) */
-#define TWL4030_MODULE_BACKUP		0x12
-#define TWL4030_MODULE_INT		0x13
-#define TWL4030_MODULE_PM_MASTER	0x14
-#define TWL4030_MODULE_PM_RECEIVER	0x15
-#define TWL4030_MODULE_RTC		0x16
-#define TWL4030_MODULE_SECURED_REG	0x17
+	TWL4030_MODULE_PM_MASTER,
+	TWL4030_MODULE_PM_RECEIVER,
+	TWL4030_MODULE_RTC,
+	TWL4030_MODULE_SECURED_REG,
+	TWL4030_MODULE_LAST,
+};
 
+/* Similar functionalities implemented in TWL4030/6030 */
 #define TWL_MODULE_USB		TWL4030_MODULE_USB
-#define TWL_MODULE_AUDIO_VOICE	TWL4030_MODULE_AUDIO_VOICE
 #define TWL_MODULE_PIH		TWL4030_MODULE_PIH
-#define TWL_MODULE_MADC		TWL4030_MODULE_MADC
 #define TWL_MODULE_MAIN_CHARGE	TWL4030_MODULE_MAIN_CHARGE
 #define TWL_MODULE_PM_MASTER	TWL4030_MODULE_PM_MASTER
 #define TWL_MODULE_PM_RECEIVER	TWL4030_MODULE_PM_RECEIVER
 #define TWL_MODULE_RTC		TWL4030_MODULE_RTC
 #define TWL_MODULE_PWM		TWL4030_MODULE_PWM0
+#define TWL_MODULE_LED		TWL4030_MODULE_LED
 
-#define TWL6030_MODULE_ID0	0x0D
-#define TWL6030_MODULE_ID1	0x0E
-#define TWL6030_MODULE_ID2	0x0F
+#define TWL6030_MODULE_ID0	13
+#define TWL6030_MODULE_ID1	14
+#define TWL6030_MODULE_ID2	15
 
 #define GPIO_INTR_OFFSET	0
 #define KEYPAD_INTR_OFFSET	1
diff --git a/include/linux/input/ti_am335x_tsc.h b/include/linux/input/ti_am335x_tsc.h
new file mode 100644
index 0000000..49269a2
--- /dev/null
+++ b/include/linux/input/ti_am335x_tsc.h
@@ -0,0 +1,23 @@
+#ifndef __LINUX_TI_AM335X_TSC_H
+#define __LINUX_TI_AM335X_TSC_H
+
+/**
+ * struct tsc_data	Touchscreen wire configuration
+ * @wires:		Wires refer to application modes
+ *			i.e. 4/5/8 wire touchscreen support
+ *			on the platform.
+ * @x_plate_resistance:	X plate resistance.
+ * @steps_to_configure:	The sequencer supports a total of
+ *			16 programmable steps.
+ *			A step configured to read a single
+ *			co-ordinate value, can be applied
+ *			more number of times for better results.
+ */
+
+struct tsc_data {
+	int wires;
+	int x_plate_resistance;
+	int steps_to_configure;
+};
+
+#endif
diff --git a/include/linux/input/ti_tscadc.h b/include/linux/input/ti_tscadc.h
deleted file mode 100644
index b10a527..0000000
--- a/include/linux/input/ti_tscadc.h
+++ /dev/null
@@ -1,17 +0,0 @@
-#ifndef __LINUX_TI_TSCADC_H
-#define __LINUX_TI_TSCADC_H
-
-/**
- * struct tsc_data	Touchscreen wire configuration
- * @wires:		Wires refer to application modes
- *			i.e. 4/5/8 wire touchscreen support
- *			on the platform.
- * @x_plate_resistance:	X plate resistance.
- */
-
-struct tsc_data {
-	int wires;
-	int x_plate_resistance;
-};
-
-#endif
diff --git a/include/linux/mfd/arizona/registers.h b/include/linux/mfd/arizona/registers.h
index ba26e99..1f6fe31 100644
--- a/include/linux/mfd/arizona/registers.h
+++ b/include/linux/mfd/arizona/registers.h
@@ -981,6 +981,7 @@
 #define ARIZONA_DSP1_CLOCKING_1                  0x1101
 #define ARIZONA_DSP1_STATUS_1                    0x1104
 #define ARIZONA_DSP1_STATUS_2                    0x1105
+#define ARIZONA_DSP1_STATUS_3                    0x1106
 #define ARIZONA_DSP2_CONTROL_1                   0x1200
 #define ARIZONA_DSP2_CLOCKING_1                  0x1201
 #define ARIZONA_DSP2_STATUS_1                    0x1204
diff --git a/include/linux/mfd/as3711.h b/include/linux/mfd/as3711.h
new file mode 100644
index 0000000..38452ce
--- /dev/null
+++ b/include/linux/mfd/as3711.h
@@ -0,0 +1,126 @@
+/*
+ * AS3711 PMIC MFC driver header
+ *
+ * Copyright (C) 2012 Renesas Electronics Corporation
+ * Author: Guennadi Liakhovetski, <g.liakhovetski@gmx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#ifndef MFD_AS3711_H
+#define MFD_AS3711_H
+
+/*
+ * Client data
+ */
+
+/* Register addresses */
+#define AS3711_SD_1_VOLTAGE		0	/* Digital Step-Down */
+#define AS3711_SD_2_VOLTAGE		1
+#define AS3711_SD_3_VOLTAGE		2
+#define AS3711_SD_4_VOLTAGE		3
+#define AS3711_LDO_1_VOLTAGE		4	/* Analog LDO */
+#define AS3711_LDO_2_VOLTAGE		5
+#define AS3711_LDO_3_VOLTAGE		6	/* Digital LDO */
+#define AS3711_LDO_4_VOLTAGE		7
+#define AS3711_LDO_5_VOLTAGE		8
+#define AS3711_LDO_6_VOLTAGE		9
+#define AS3711_LDO_7_VOLTAGE		0xa
+#define AS3711_LDO_8_VOLTAGE		0xb
+#define AS3711_SD_CONTROL		0x10
+#define AS3711_GPIO_SIGNAL_OUT		0x20
+#define AS3711_GPIO_SIGNAL_IN		0x21
+#define AS3711_SD_CONTROL_1		0x30
+#define AS3711_SD_CONTROL_2		0x31
+#define AS3711_CURR_CONTROL		0x40
+#define AS3711_CURR1_VALUE		0x43
+#define AS3711_CURR2_VALUE		0x44
+#define AS3711_CURR3_VALUE		0x45
+#define AS3711_STEPUP_CONTROL_1		0x50
+#define AS3711_STEPUP_CONTROL_2		0x51
+#define AS3711_STEPUP_CONTROL_4		0x53
+#define AS3711_STEPUP_CONTROL_5		0x54
+#define AS3711_REG_STATUS		0x73
+#define AS3711_INTERRUPT_STATUS_1	0x77
+#define AS3711_INTERRUPT_STATUS_2	0x78
+#define AS3711_INTERRUPT_STATUS_3	0x79
+#define AS3711_CHARGER_STATUS_1		0x86
+#define AS3711_CHARGER_STATUS_2		0x87
+#define AS3711_ASIC_ID_1		0x90
+#define AS3711_ASIC_ID_2		0x91
+
+#define AS3711_MAX_REGS			0x92
+
+/* Regulators */
+enum {
+	AS3711_REGULATOR_SD_1,
+	AS3711_REGULATOR_SD_2,
+	AS3711_REGULATOR_SD_3,
+	AS3711_REGULATOR_SD_4,
+	AS3711_REGULATOR_LDO_1,
+	AS3711_REGULATOR_LDO_2,
+	AS3711_REGULATOR_LDO_3,
+	AS3711_REGULATOR_LDO_4,
+	AS3711_REGULATOR_LDO_5,
+	AS3711_REGULATOR_LDO_6,
+	AS3711_REGULATOR_LDO_7,
+	AS3711_REGULATOR_LDO_8,
+
+	AS3711_REGULATOR_MAX,
+};
+
+struct device;
+struct regmap;
+
+struct as3711 {
+	struct device *dev;
+	struct regmap *regmap;
+};
+
+#define AS3711_MAX_STEPDOWN 4
+#define AS3711_MAX_STEPUP 2
+#define AS3711_MAX_LDO 8
+
+enum as3711_su2_feedback {
+	AS3711_SU2_VOLTAGE,
+	AS3711_SU2_CURR1,
+	AS3711_SU2_CURR2,
+	AS3711_SU2_CURR3,
+	AS3711_SU2_CURR_AUTO,
+};
+
+enum as3711_su2_fbprot {
+	AS3711_SU2_LX_SD4,
+	AS3711_SU2_GPIO2,
+	AS3711_SU2_GPIO3,
+	AS3711_SU2_GPIO4,
+};
+
+/*
+ * Platform data
+ */
+
+struct as3711_regulator_pdata {
+	struct regulator_init_data *init_data[AS3711_REGULATOR_MAX];
+};
+
+struct as3711_bl_pdata {
+	const char *su1_fb;
+	int su1_max_uA;
+	const char *su2_fb;
+	int su2_max_uA;
+	enum as3711_su2_feedback su2_feedback;
+	enum as3711_su2_fbprot su2_fbprot;
+	bool su2_auto_curr1;
+	bool su2_auto_curr2;
+	bool su2_auto_curr3;
+};
+
+struct as3711_platform_data {
+	struct as3711_regulator_pdata regulator;
+	struct as3711_bl_pdata backlight;
+};
+
+#endif
diff --git a/include/linux/mfd/da9052/da9052.h b/include/linux/mfd/da9052/da9052.h
index 0507c4c..86dd93d 100644
--- a/include/linux/mfd/da9052/da9052.h
+++ b/include/linux/mfd/da9052/da9052.h
@@ -146,4 +146,14 @@
 
 extern struct regmap_config da9052_regmap_config;
 
+int da9052_irq_init(struct da9052 *da9052);
+int da9052_irq_exit(struct da9052 *da9052);
+int da9052_request_irq(struct da9052 *da9052, int irq, char *name,
+			   irq_handler_t handler, void *data);
+void da9052_free_irq(struct da9052 *da9052, int irq, void *data);
+
+int da9052_enable_irq(struct da9052 *da9052, int irq);
+int da9052_disable_irq(struct da9052 *da9052, int irq);
+int da9052_disable_irq_nosync(struct da9052 *da9052, int irq);
+
 #endif /* __MFD_DA9052_DA9052_H */
diff --git a/include/linux/mfd/da9055/core.h b/include/linux/mfd/da9055/core.h
index c96ad68..956afa4 100644
--- a/include/linux/mfd/da9055/core.h
+++ b/include/linux/mfd/da9055/core.h
@@ -1,4 +1,4 @@
-﻿/*
+/*
  * da9055 declarations for DA9055 PMICs.
  *
  * Copyright(c) 2012 Dialog Semiconductor Ltd.
diff --git a/include/linux/mfd/da9055/pdata.h b/include/linux/mfd/da9055/pdata.h
index f87a6c1..04e092b 100644
--- a/include/linux/mfd/da9055/pdata.h
+++ b/include/linux/mfd/da9055/pdata.h
@@ -1,4 +1,4 @@
-﻿/* Copyright (C) 2012 Dialog Semiconductor Ltd.
+/* Copyright (C) 2012 Dialog Semiconductor Ltd.
  *
  *  This program is free software; you can redistribute it and/or modify
  *  it under the terms of the GNU General Public License as published by
diff --git a/include/linux/mfd/da9055/reg.h b/include/linux/mfd/da9055/reg.h
index df237ee..2b592e0 100644
--- a/include/linux/mfd/da9055/reg.h
+++ b/include/linux/mfd/da9055/reg.h
@@ -1,4 +1,4 @@
-﻿/*
+/*
  * DA9055 declarations for DA9055 PMICs.
  *
  * Copyright(c) 2012 Dialog Semiconductor Ltd.
diff --git a/include/linux/mfd/rc5t583.h b/include/linux/mfd/rc5t583.h
index 36c242e..fd413cc 100644
--- a/include/linux/mfd/rc5t583.h
+++ b/include/linux/mfd/rc5t583.h
@@ -33,6 +33,7 @@
 /* Maximum number of main interrupts */
 #define MAX_MAIN_INTERRUPT		5
 #define RC5T583_MAX_GPEDGE_REG		2
+#define RC5T583_MAX_INTERRUPT_EN_REGS	8
 #define RC5T583_MAX_INTERRUPT_MASK_REGS	9
 
 /* Interrupt enable register */
@@ -304,7 +305,7 @@
 	uint8_t		intc_inten_reg;
 
 	/* For group interrupt bits and address */
-	uint8_t		irq_en_reg[RC5T583_MAX_INTERRUPT_MASK_REGS];
+	uint8_t		irq_en_reg[RC5T583_MAX_INTERRUPT_EN_REGS];
 
 	/* For gpio edge */
 	uint8_t		gpedge_reg[RC5T583_MAX_GPEDGE_REG];
diff --git a/include/linux/mfd/retu.h b/include/linux/mfd/retu.h
new file mode 100644
index 0000000..1e2715d
--- /dev/null
+++ b/include/linux/mfd/retu.h
@@ -0,0 +1,22 @@
+/*
+ * Retu MFD driver interface
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ */
+
+#ifndef __LINUX_MFD_RETU_H
+#define __LINUX_MFD_RETU_H
+
+struct retu_dev;
+
+int retu_read(struct retu_dev *, u8);
+int retu_write(struct retu_dev *, u8, u16);
+
+/* Registers */
+#define RETU_REG_WATCHDOG	0x17		/* Watchdog */
+#define RETU_REG_CC1		0x0d		/* Common control register 1 */
+#define RETU_REG_STATUS		0x16		/* Status register */
+
+#endif /* __LINUX_MFD_RETU_H */
diff --git a/include/linux/mfd/sta2x11-mfd.h b/include/linux/mfd/sta2x11-mfd.h
index d179227..9a855ac 100644
--- a/include/linux/mfd/sta2x11-mfd.h
+++ b/include/linux/mfd/sta2x11-mfd.h
@@ -26,6 +26,28 @@
 #include <linux/types.h>
 #include <linux/pci.h>
 
+enum sta2x11_mfd_plat_dev {
+	sta2x11_sctl = 0,
+	sta2x11_gpio,
+	sta2x11_scr,
+	sta2x11_time,
+	sta2x11_apbreg,
+	sta2x11_apb_soc_regs,
+	sta2x11_vic,
+	sta2x11_n_mfd_plat_devs,
+};
+
+#define STA2X11_MFD_SCTL_NAME	       "sta2x11-sctl"
+#define STA2X11_MFD_GPIO_NAME	       "sta2x11-gpio"
+#define STA2X11_MFD_SCR_NAME	       "sta2x11-scr"
+#define STA2X11_MFD_TIME_NAME	       "sta2x11-time"
+#define STA2X11_MFD_APBREG_NAME	       "sta2x11-apbreg"
+#define STA2X11_MFD_APB_SOC_REGS_NAME  "sta2x11-apb-soc-regs"
+#define STA2X11_MFD_VIC_NAME	       "sta2x11-vic"
+
+extern u32
+__sta2x11_mfd_mask(struct pci_dev *, u32, u32, u32, enum sta2x11_mfd_plat_dev);
+
 /*
  * The MFD PCI block includes the GPIO peripherals and other register blocks.
  * For GPIO, we have 32*4 bits (I use "gsta" for "gpio sta2x11".)
@@ -182,7 +204,11 @@
  * The APB bridge has its own registers, needed by our users as well.
  * They are accessed with the following read/mask/write function.
  */
-u32 sta2x11_apbreg_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val);
+static inline u32
+sta2x11_apbreg_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+{
+	return __sta2x11_mfd_mask(pdev, reg, mask, val, sta2x11_apbreg);
+}
 
 /* CAN and MLB */
 #define APBREG_BSR	0x00	/* Bridge Status Reg */
@@ -211,19 +237,45 @@
  * The system controller has its own registers. Some of these are accessed
  * by out users as well, using the following read/mask/write/function
  */
-u32 sta2x11_sctl_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val);
+static inline
+u32 sta2x11_sctl_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+{
+	return __sta2x11_mfd_mask(pdev, reg, mask, val, sta2x11_sctl);
+}
 
 #define SCTL_SCCTL		0x00	/* System controller control register */
 #define SCTL_ARMCFG		0x04	/* ARM configuration register */
 #define SCTL_SCPLLCTL		0x08	/* PLL control status register */
+
+#define SCTL_SCPLLCTL_AUDIO_PLL_PD	     BIT(1)
+#define SCTL_SCPLLCTL_FRAC_CONTROL	     BIT(3)
+#define SCTL_SCPLLCTL_STRB_BYPASS	     BIT(6)
+#define SCTL_SCPLLCTL_STRB_INPUT	     BIT(8)
+
 #define SCTL_SCPLLFCTRL		0x0c	/* PLL frequency control register */
+
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_NDIV_MASK	0xff
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_NDIV_SHIFT	  10
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_IDF_MASK	   7
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_IDF_SHIFT	  21
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_ODF_MASK	   7
+#define SCTL_SCPLLFCTRL_AUDIO_PLL_ODF_SHIFT	  18
+#define SCTL_SCPLLFCTRL_DITHER_DISABLE_MASK     0x03
+#define SCTL_SCPLLFCTRL_DITHER_DISABLE_SHIFT       4
+
+
 #define SCTL_SCRESFRACT		0x10	/* PLL fractional input register */
+
+#define SCTL_SCRESFRACT_MASK	0x0000ffff
+
+
 #define SCTL_SCRESCTRL1		0x14	/* Peripheral reset control 1 */
 #define SCTL_SCRESXTRL2		0x18	/* Peripheral reset control 2 */
 #define SCTL_SCPEREN0		0x1c	/* Peripheral clock enable register 0 */
 #define SCTL_SCPEREN1		0x20	/* Peripheral clock enable register 1 */
 #define SCTL_SCPEREN2		0x24	/* Peripheral clock enable register 2 */
 #define SCTL_SCGRST		0x28	/* Peripheral global reset */
+#define SCTL_SCPCIECSBRST       0x2c    /* PCIe PAB CSB reset status register */
 #define SCTL_SCPCIPMCR1		0x30	/* PCI power management control 1 */
 #define SCTL_SCPCIPMCR2		0x34	/* PCI power management control 2 */
 #define SCTL_SCPCIPMSR1		0x38	/* PCI power management status 1 */
@@ -321,4 +373,146 @@
 #define SCTL_SCPEREN1_I2C3		(1 << 16)
 #define SCTL_SCPEREN1_USB_PHY		(1 << 17)
 
+/*
+ * APB-SOC registers
+ */
+static inline
+u32 sta2x11_apb_soc_regs_mask(struct pci_dev *pdev, u32 reg, u32 mask, u32 val)
+{
+	return __sta2x11_mfd_mask(pdev, reg, mask, val, sta2x11_apb_soc_regs);
+}
+
+#define PCIE_EP1_FUNC3_0_INTR_REG	0x000
+#define PCIE_EP1_FUNC7_4_INTR_REG	0x004
+#define PCIE_EP2_FUNC3_0_INTR_REG	0x008
+#define PCIE_EP2_FUNC7_4_INTR_REG	0x00c
+#define PCIE_EP3_FUNC3_0_INTR_REG	0x010
+#define PCIE_EP3_FUNC7_4_INTR_REG	0x014
+#define PCIE_EP4_FUNC3_0_INTR_REG	0x018
+#define PCIE_EP4_FUNC7_4_INTR_REG	0x01c
+#define PCIE_INTR_ENABLE0_REG		0x020
+#define PCIE_INTR_ENABLE1_REG		0x024
+#define PCIE_EP1_FUNC_TC_REG		0x028
+#define PCIE_EP2_FUNC_TC_REG		0x02c
+#define PCIE_EP3_FUNC_TC_REG		0x030
+#define PCIE_EP4_FUNC_TC_REG		0x034
+#define PCIE_EP1_FUNC_F_REG		0x038
+#define PCIE_EP2_FUNC_F_REG		0x03c
+#define PCIE_EP3_FUNC_F_REG		0x040
+#define PCIE_EP4_FUNC_F_REG		0x044
+#define PCIE_PAB_AMBA_SW_RST_REG	0x048
+#define PCIE_PM_STATUS_0_PORT_0_4	0x04c
+#define PCIE_PM_STATUS_7_0_EP1		0x050
+#define PCIE_PM_STATUS_7_0_EP2		0x054
+#define PCIE_PM_STATUS_7_0_EP3		0x058
+#define PCIE_PM_STATUS_7_0_EP4		0x05c
+#define PCIE_DEV_ID_0_EP1_REG		0x060
+#define PCIE_CC_REV_ID_0_EP1_REG	0x064
+#define PCIE_DEV_ID_1_EP1_REG		0x068
+#define PCIE_CC_REV_ID_1_EP1_REG	0x06c
+#define PCIE_DEV_ID_2_EP1_REG		0x070
+#define PCIE_CC_REV_ID_2_EP1_REG	0x074
+#define PCIE_DEV_ID_3_EP1_REG		0x078
+#define PCIE_CC_REV_ID_3_EP1_REG	0x07c
+#define PCIE_DEV_ID_4_EP1_REG		0x080
+#define PCIE_CC_REV_ID_4_EP1_REG	0x084
+#define PCIE_DEV_ID_5_EP1_REG		0x088
+#define PCIE_CC_REV_ID_5_EP1_REG	0x08c
+#define PCIE_DEV_ID_6_EP1_REG		0x090
+#define PCIE_CC_REV_ID_6_EP1_REG	0x094
+#define PCIE_DEV_ID_7_EP1_REG		0x098
+#define PCIE_CC_REV_ID_7_EP1_REG	0x09c
+#define PCIE_DEV_ID_0_EP2_REG		0x0a0
+#define PCIE_CC_REV_ID_0_EP2_REG	0x0a4
+#define PCIE_DEV_ID_1_EP2_REG		0x0a8
+#define PCIE_CC_REV_ID_1_EP2_REG	0x0ac
+#define PCIE_DEV_ID_2_EP2_REG		0x0b0
+#define PCIE_CC_REV_ID_2_EP2_REG	0x0b4
+#define PCIE_DEV_ID_3_EP2_REG		0x0b8
+#define PCIE_CC_REV_ID_3_EP2_REG	0x0bc
+#define PCIE_DEV_ID_4_EP2_REG		0x0c0
+#define PCIE_CC_REV_ID_4_EP2_REG	0x0c4
+#define PCIE_DEV_ID_5_EP2_REG		0x0c8
+#define PCIE_CC_REV_ID_5_EP2_REG	0x0cc
+#define PCIE_DEV_ID_6_EP2_REG		0x0d0
+#define PCIE_CC_REV_ID_6_EP2_REG	0x0d4
+#define PCIE_DEV_ID_7_EP2_REG		0x0d8
+#define PCIE_CC_REV_ID_7_EP2_REG	0x0dC
+#define PCIE_DEV_ID_0_EP3_REG		0x0e0
+#define PCIE_CC_REV_ID_0_EP3_REG	0x0e4
+#define PCIE_DEV_ID_1_EP3_REG		0x0e8
+#define PCIE_CC_REV_ID_1_EP3_REG	0x0ec
+#define PCIE_DEV_ID_2_EP3_REG		0x0f0
+#define PCIE_CC_REV_ID_2_EP3_REG	0x0f4
+#define PCIE_DEV_ID_3_EP3_REG		0x0f8
+#define PCIE_CC_REV_ID_3_EP3_REG	0x0fc
+#define PCIE_DEV_ID_4_EP3_REG		0x100
+#define PCIE_CC_REV_ID_4_EP3_REG	0x104
+#define PCIE_DEV_ID_5_EP3_REG		0x108
+#define PCIE_CC_REV_ID_5_EP3_REG	0x10c
+#define PCIE_DEV_ID_6_EP3_REG		0x110
+#define PCIE_CC_REV_ID_6_EP3_REG	0x114
+#define PCIE_DEV_ID_7_EP3_REG		0x118
+#define PCIE_CC_REV_ID_7_EP3_REG	0x11c
+#define PCIE_DEV_ID_0_EP4_REG		0x120
+#define PCIE_CC_REV_ID_0_EP4_REG	0x124
+#define PCIE_DEV_ID_1_EP4_REG		0x128
+#define PCIE_CC_REV_ID_1_EP4_REG	0x12c
+#define PCIE_DEV_ID_2_EP4_REG		0x130
+#define PCIE_CC_REV_ID_2_EP4_REG	0x134
+#define PCIE_DEV_ID_3_EP4_REG		0x138
+#define PCIE_CC_REV_ID_3_EP4_REG	0x13c
+#define PCIE_DEV_ID_4_EP4_REG		0x140
+#define PCIE_CC_REV_ID_4_EP4_REG	0x144
+#define PCIE_DEV_ID_5_EP4_REG		0x148
+#define PCIE_CC_REV_ID_5_EP4_REG	0x14c
+#define PCIE_DEV_ID_6_EP4_REG		0x150
+#define PCIE_CC_REV_ID_6_EP4_REG	0x154
+#define PCIE_DEV_ID_7_EP4_REG		0x158
+#define PCIE_CC_REV_ID_7_EP4_REG	0x15c
+#define PCIE_SUBSYS_VEN_ID_REG		0x160
+#define PCIE_COMMON_CLOCK_CONFIG_0_4_0	0x164
+#define PCIE_MIPHYP_SSC_EN_REG		0x168
+#define PCIE_MIPHYP_ADDR_REG		0x16c
+#define PCIE_L1_ASPM_READY_REG		0x170
+#define PCIE_EXT_CFG_RDY_REG		0x174
+#define PCIE_SoC_INT_ROUTER_STATUS0_REG 0x178
+#define PCIE_SoC_INT_ROUTER_STATUS1_REG 0x17c
+#define PCIE_SoC_INT_ROUTER_STATUS2_REG 0x180
+#define PCIE_SoC_INT_ROUTER_STATUS3_REG 0x184
+#define DMA_IP_CTRL_REG			0x324
+#define DISP_BRIDGE_PU_PD_CTRL_REG	0x328
+#define VIP_PU_PD_CTRL_REG		0x32c
+#define USB_MLB_PU_PD_CTRL_REG		0x330
+#define SDIO_PU_PD_MISCFUNC_CTRL_REG1	0x334
+#define SDIO_PU_PD_MISCFUNC_CTRL_REG2	0x338
+#define UART_PU_PD_CTRL_REG		0x33c
+#define ARM_Lock			0x340
+#define SYS_IO_CHAR_REG1		0x344
+#define SYS_IO_CHAR_REG2		0x348
+#define SATA_CORE_ID_REG		0x34c
+#define SATA_CTRL_REG			0x350
+#define I2C_HSFIX_MISC_REG		0x354
+#define SPARE2_RESERVED			0x358
+#define SPARE3_RESERVED			0x35c
+#define MASTER_LOCK_REG			0x368
+#define SYSTEM_CONFIG_STATUS_REG	0x36c
+#define MSP_CLK_CTRL_REG		0x39c
+#define COMPENSATION_REG1		0x3c4
+#define COMPENSATION_REG2		0x3c8
+#define COMPENSATION_REG3		0x3cc
+#define TEST_CTL_REG			0x3d0
+
+/*
+ * SECR (OTP) registers
+ */
+#define STA2X11_SECR_CR			0x00
+#define STA2X11_SECR_FVR0		0x10
+#define STA2X11_SECR_FVR1		0x14
+
+extern int sta2x11_mfd_get_regs_data(struct platform_device *pdev,
+				     enum sta2x11_mfd_plat_dev index,
+				     void __iomem **regs,
+				     spinlock_t **lock);
+
 #endif /* __STA2X11_MFD_H */
diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
index f8d5b4d..383ac15 100644
--- a/include/linux/mfd/stmpe.h
+++ b/include/linux/mfd/stmpe.h
@@ -62,6 +62,7 @@
  * @lock: lock protecting I/O operations
  * @irq_lock: IRQ bus lock
  * @dev: device, mostly for dev_dbg()
+ * @irq_domain: IRQ domain
  * @client: client - i2c or spi
  * @ci: client specific information
  * @partnum: part number
@@ -79,6 +80,7 @@
 	struct mutex lock;
 	struct mutex irq_lock;
 	struct device *dev;
+	struct irq_domain *domain;
 	void *client;
 	struct stmpe_client_info *ci;
 	enum stmpe_partnum partnum;
@@ -188,7 +190,6 @@
  * @id: device id to distinguish between multiple STMPEs on the same board
  * @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
  * @irq_trigger: IRQ trigger to use for the interrupt to the host
- * @irq_invert_polarity: IRQ line is connected with reversed polarity
  * @autosleep: bool to enable/disable stmpe autosleep
  * @autosleep_timeout: inactivity timeout in milliseconds for autosleep
  * @irq_base: base IRQ number.  %STMPE_NR_IRQS irqs will be used, or
@@ -205,7 +206,6 @@
 	unsigned int blocks;
 	int irq_base;
 	unsigned int irq_trigger;
-	bool irq_invert_polarity;
 	bool autosleep;
 	bool irq_over_gpio;
 	int irq_gpio;
diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h
new file mode 100644
index 0000000..c79ad5d
--- /dev/null
+++ b/include/linux/mfd/ti_am335x_tscadc.h
@@ -0,0 +1,152 @@
+#ifndef __LINUX_TI_AM335X_TSCADC_MFD_H
+#define __LINUX_TI_AM335X_TSCADC_MFD_H
+
+/*
+ * TI Touch Screen / ADC MFD driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/mfd/core.h>
+
+#define REG_RAWIRQSTATUS	0x024
+#define REG_IRQSTATUS		0x028
+#define REG_IRQENABLE		0x02C
+#define REG_IRQCLR		0x030
+#define REG_IRQWAKEUP		0x034
+#define REG_CTRL		0x040
+#define REG_ADCFSM		0x044
+#define REG_CLKDIV		0x04C
+#define REG_SE			0x054
+#define REG_IDLECONFIG		0x058
+#define REG_CHARGECONFIG	0x05C
+#define REG_CHARGEDELAY		0x060
+#define REG_STEPCONFIG(n)	(0x64 + ((n - 1) * 8))
+#define REG_STEPDELAY(n)	(0x68 + ((n - 1) * 8))
+#define REG_FIFO0CNT		0xE4
+#define REG_FIFO0THR		0xE8
+#define REG_FIFO1CNT		0xF0
+#define REG_FIFO1THR		0xF4
+#define REG_FIFO0		0x100
+#define REG_FIFO1		0x200
+
+/*	Register Bitfields	*/
+/* IRQ wakeup enable */
+#define IRQWKUP_ENB		BIT(0)
+
+/* Step Enable */
+#define STEPENB_MASK		(0x1FFFF << 0)
+#define STEPENB(val)		((val) << 0)
+#define STPENB_STEPENB		STEPENB(0x1FFFF)
+#define STPENB_STEPENB_TC	STEPENB(0x1FFF)
+
+/* IRQ enable */
+#define IRQENB_HW_PEN		BIT(0)
+#define IRQENB_FIFO0THRES	BIT(2)
+#define IRQENB_FIFO1THRES	BIT(5)
+#define IRQENB_PENUP		BIT(9)
+
+/* Step Configuration */
+#define STEPCONFIG_MODE_MASK	(3 << 0)
+#define STEPCONFIG_MODE(val)	((val) << 0)
+#define STEPCONFIG_MODE_HWSYNC	STEPCONFIG_MODE(2)
+#define STEPCONFIG_AVG_MASK	(7 << 2)
+#define STEPCONFIG_AVG(val)	((val) << 2)
+#define STEPCONFIG_AVG_16	STEPCONFIG_AVG(4)
+#define STEPCONFIG_XPP		BIT(5)
+#define STEPCONFIG_XNN		BIT(6)
+#define STEPCONFIG_YPP		BIT(7)
+#define STEPCONFIG_YNN		BIT(8)
+#define STEPCONFIG_XNP		BIT(9)
+#define STEPCONFIG_YPN		BIT(10)
+#define STEPCONFIG_INM_MASK	(0xF << 15)
+#define STEPCONFIG_INM(val)	((val) << 15)
+#define STEPCONFIG_INM_ADCREFM	STEPCONFIG_INM(8)
+#define STEPCONFIG_INP_MASK	(0xF << 19)
+#define STEPCONFIG_INP(val)	((val) << 19)
+#define STEPCONFIG_INP_AN2	STEPCONFIG_INP(2)
+#define STEPCONFIG_INP_AN3	STEPCONFIG_INP(3)
+#define STEPCONFIG_INP_AN4	STEPCONFIG_INP(4)
+#define STEPCONFIG_INP_ADCREFM	STEPCONFIG_INP(8)
+#define STEPCONFIG_FIFO1	BIT(26)
+
+/* Delay register */
+#define STEPDELAY_OPEN_MASK	(0x3FFFF << 0)
+#define STEPDELAY_OPEN(val)	((val) << 0)
+#define STEPCONFIG_OPENDLY	STEPDELAY_OPEN(0x098)
+#define STEPDELAY_SAMPLE_MASK	(0xFF << 24)
+#define STEPDELAY_SAMPLE(val)	((val) << 24)
+#define STEPCONFIG_SAMPLEDLY	STEPDELAY_SAMPLE(0)
+
+/* Charge Config */
+#define STEPCHARGE_RFP_MASK	(7 << 12)
+#define STEPCHARGE_RFP(val)	((val) << 12)
+#define STEPCHARGE_RFP_XPUL	STEPCHARGE_RFP(1)
+#define STEPCHARGE_INM_MASK	(0xF << 15)
+#define STEPCHARGE_INM(val)	((val) << 15)
+#define STEPCHARGE_INM_AN1	STEPCHARGE_INM(1)
+#define STEPCHARGE_INP_MASK	(0xF << 19)
+#define STEPCHARGE_INP(val)	((val) << 19)
+#define STEPCHARGE_INP_AN1	STEPCHARGE_INP(1)
+#define STEPCHARGE_RFM_MASK	(3 << 23)
+#define STEPCHARGE_RFM(val)	((val) << 23)
+#define STEPCHARGE_RFM_XNUR	STEPCHARGE_RFM(1)
+
+/* Charge delay */
+#define CHARGEDLY_OPEN_MASK	(0x3FFFF << 0)
+#define CHARGEDLY_OPEN(val)	((val) << 0)
+#define CHARGEDLY_OPENDLY	CHARGEDLY_OPEN(1)
+
+/* Control register */
+#define CNTRLREG_TSCSSENB	BIT(0)
+#define CNTRLREG_STEPID		BIT(1)
+#define CNTRLREG_STEPCONFIGWRT	BIT(2)
+#define CNTRLREG_POWERDOWN	BIT(4)
+#define CNTRLREG_AFE_CTRL_MASK	(3 << 5)
+#define CNTRLREG_AFE_CTRL(val)	((val) << 5)
+#define CNTRLREG_4WIRE		CNTRLREG_AFE_CTRL(1)
+#define CNTRLREG_5WIRE		CNTRLREG_AFE_CTRL(2)
+#define CNTRLREG_8WIRE		CNTRLREG_AFE_CTRL(3)
+#define CNTRLREG_TSCENB		BIT(7)
+
+#define ADC_CLK			3000000
+#define	MAX_CLK_DIV		7
+#define TOTAL_STEPS		16
+#define TOTAL_CHANNELS		8
+
+#define TSCADC_CELLS		2
+
+enum tscadc_cells {
+	TSC_CELL,
+	ADC_CELL,
+};
+
+struct mfd_tscadc_board {
+	struct tsc_data *tsc_init;
+	struct adc_data *adc_init;
+};
+
+struct ti_tscadc_dev {
+	struct device *dev;
+	struct regmap *regmap_tscadc;
+	void __iomem *tscadc_base;
+	int irq;
+	struct mfd_cell cells[TSCADC_CELLS];
+
+	/* tsc device */
+	struct titsc *tsc;
+
+	/* adc device */
+	struct adc_device *adc;
+};
+
+#endif
diff --git a/include/linux/mfd/tps65090.h b/include/linux/mfd/tps65090.h
index 804e280..6694cf4 100644
--- a/include/linux/mfd/tps65090.h
+++ b/include/linux/mfd/tps65090.h
@@ -23,6 +23,26 @@
 #define __LINUX_MFD_TPS65090_H
 
 #include <linux/irq.h>
+#include <linux/regmap.h>
+
+/* TPS65090 IRQs */
+enum {
+	TPS65090_IRQ_VAC_STATUS_CHANGE,
+	TPS65090_IRQ_VSYS_STATUS_CHANGE,
+	TPS65090_IRQ_BAT_STATUS_CHANGE,
+	TPS65090_IRQ_CHARGING_STATUS_CHANGE,
+	TPS65090_IRQ_CHARGING_COMPLETE,
+	TPS65090_IRQ_OVERLOAD_DCDC1,
+	TPS65090_IRQ_OVERLOAD_DCDC2,
+	TPS65090_IRQ_OVERLOAD_DCDC3,
+	TPS65090_IRQ_OVERLOAD_FET1,
+	TPS65090_IRQ_OVERLOAD_FET2,
+	TPS65090_IRQ_OVERLOAD_FET3,
+	TPS65090_IRQ_OVERLOAD_FET4,
+	TPS65090_IRQ_OVERLOAD_FET5,
+	TPS65090_IRQ_OVERLOAD_FET6,
+	TPS65090_IRQ_OVERLOAD_FET7,
+};
 
 /* TPS65090 Regulator ID */
 enum {
@@ -44,20 +64,9 @@
 };
 
 struct tps65090 {
-	struct mutex		lock;
 	struct device		*dev;
-	struct i2c_client	*client;
 	struct regmap		*rmap;
-	struct irq_chip		irq_chip;
-	struct mutex		irq_lock;
-	int			irq_base;
-	unsigned int		id;
-};
-
-struct tps65090_subdev_info {
-	int		id;
-	const char	*name;
-	void		*platform_data;
+	struct regmap_irq_chip_data *irq_data;
 };
 
 /*
@@ -77,8 +86,6 @@
 
 struct tps65090_platform_data {
 	int irq_base;
-	int num_subdevs;
-	struct tps65090_subdev_info *subdevs;
 	struct tps65090_regulator_plat_data *reg_pdata[TPS65090_REGULATOR_MAX];
 };
 
@@ -86,9 +93,39 @@
  * NOTE: the functions below are not intended for use outside
  * of the TPS65090 sub-device drivers
  */
-extern int tps65090_write(struct device *dev, int reg, uint8_t val);
-extern int tps65090_read(struct device *dev, int reg, uint8_t *val);
-extern int tps65090_set_bits(struct device *dev, int reg, uint8_t bit_num);
-extern int tps65090_clr_bits(struct device *dev, int reg, uint8_t bit_num);
+static inline int tps65090_write(struct device *dev, int reg, uint8_t val)
+{
+	struct tps65090 *tps = dev_get_drvdata(dev);
+
+	return regmap_write(tps->rmap, reg, val);
+}
+
+static inline int tps65090_read(struct device *dev, int reg, uint8_t *val)
+{
+	struct tps65090 *tps = dev_get_drvdata(dev);
+	unsigned int temp_val;
+	int ret;
+
+	ret = regmap_read(tps->rmap, reg, &temp_val);
+	if (!ret)
+		*val = temp_val;
+	return ret;
+}
+
+static inline int tps65090_set_bits(struct device *dev, int reg,
+		uint8_t bit_num)
+{
+	struct tps65090 *tps = dev_get_drvdata(dev);
+
+	return regmap_update_bits(tps->rmap, reg, BIT(bit_num), ~0u);
+}
+
+static inline int tps65090_clr_bits(struct device *dev, int reg,
+		uint8_t bit_num)
+{
+	struct tps65090 *tps = dev_get_drvdata(dev);
+
+	return regmap_update_bits(tps->rmap, reg, BIT(bit_num), 0u);
+}
 
 #endif /*__LINUX_MFD_TPS65090_H */
diff --git a/include/linux/mfd/tps6586x.h b/include/linux/mfd/tps6586x.h
index f8da0e1..8799454 100644
--- a/include/linux/mfd/tps6586x.h
+++ b/include/linux/mfd/tps6586x.h
@@ -96,5 +96,6 @@
 extern int tps6586x_clr_bits(struct device *dev, int reg, uint8_t bit_mask);
 extern int tps6586x_update(struct device *dev, int reg, uint8_t val,
 			   uint8_t mask);
+extern int tps6586x_irq_get_virq(struct device *dev, int irq);
 
 #endif /*__LINUX_MFD_TPS6586X_H */
diff --git a/include/linux/mfd/tps65910.h b/include/linux/mfd/tps65910.h
index 02e894f..20e433e 100644
--- a/include/linux/mfd/tps65910.h
+++ b/include/linux/mfd/tps65910.h
@@ -572,6 +572,49 @@
 #define SPARE_SPARE_MASK				0xFF
 #define SPARE_SPARE_SHIFT				0
 
+#define TPS65910_INT_STS_RTC_PERIOD_IT_MASK			0x80
+#define TPS65910_INT_STS_RTC_PERIOD_IT_SHIFT			7
+#define TPS65910_INT_STS_RTC_ALARM_IT_MASK			0x40
+#define TPS65910_INT_STS_RTC_ALARM_IT_SHIFT			6
+#define TPS65910_INT_STS_HOTDIE_IT_MASK				0x20
+#define TPS65910_INT_STS_HOTDIE_IT_SHIFT			5
+#define TPS65910_INT_STS_PWRHOLD_F_IT_MASK			0x10
+#define TPS65910_INT_STS_PWRHOLD_F_IT_SHIFT			4
+#define TPS65910_INT_STS_PWRON_LP_IT_MASK			0x08
+#define TPS65910_INT_STS_PWRON_LP_IT_SHIFT			3
+#define TPS65910_INT_STS_PWRON_IT_MASK				0x04
+#define TPS65910_INT_STS_PWRON_IT_SHIFT				2
+#define TPS65910_INT_STS_VMBHI_IT_MASK				0x02
+#define TPS65910_INT_STS_VMBHI_IT_SHIFT				1
+#define TPS65910_INT_STS_VMBDCH_IT_MASK				0x01
+#define TPS65910_INT_STS_VMBDCH_IT_SHIFT			0
+
+#define TPS65910_INT_MSK_RTC_PERIOD_IT_MSK_MASK			0x80
+#define TPS65910_INT_MSK_RTC_PERIOD_IT_MSK_SHIFT		7
+#define TPS65910_INT_MSK_RTC_ALARM_IT_MSK_MASK			0x40
+#define TPS65910_INT_MSK_RTC_ALARM_IT_MSK_SHIFT			6
+#define TPS65910_INT_MSK_HOTDIE_IT_MSK_MASK			0x20
+#define TPS65910_INT_MSK_HOTDIE_IT_MSK_SHIFT			5
+#define TPS65910_INT_MSK_PWRHOLD_IT_MSK_MASK			0x10
+#define TPS65910_INT_MSK_PWRHOLD_IT_MSK_SHIFT			4
+#define TPS65910_INT_MSK_PWRON_LP_IT_MSK_MASK			0x08
+#define TPS65910_INT_MSK_PWRON_LP_IT_MSK_SHIFT			3
+#define TPS65910_INT_MSK_PWRON_IT_MSK_MASK			0x04
+#define TPS65910_INT_MSK_PWRON_IT_MSK_SHIFT			2
+#define TPS65910_INT_MSK_VMBHI_IT_MSK_MASK			0x02
+#define TPS65910_INT_MSK_VMBHI_IT_MSK_SHIFT			1
+#define TPS65910_INT_MSK_VMBDCH_IT_MSK_MASK			0x01
+#define TPS65910_INT_MSK_VMBDCH_IT_MSK_SHIFT			0
+
+#define TPS65910_INT_STS2_GPIO0_F_IT_SHIFT			2
+#define TPS65910_INT_STS2_GPIO0_F_IT_MASK			0x02
+#define TPS65910_INT_STS2_GPIO0_R_IT_SHIFT			1
+#define TPS65910_INT_STS2_GPIO0_R_IT_MASK			0x01
+
+#define TPS65910_INT_MSK2_GPIO0_F_IT_MSK_SHIFT			2
+#define TPS65910_INT_MSK2_GPIO0_F_IT_MSK_MASK			0x02
+#define TPS65910_INT_MSK2_GPIO0_R_IT_MSK_SHIFT			1
+#define TPS65910_INT_MSK2_GPIO0_R_IT_MSK_MASK			0x01
 
 /*Register INT_STS  (0x80) register.RegisterDescription */
 #define INT_STS_RTC_PERIOD_IT_MASK			0x80
@@ -580,16 +623,16 @@
 #define INT_STS_RTC_ALARM_IT_SHIFT			6
 #define INT_STS_HOTDIE_IT_MASK				0x20
 #define INT_STS_HOTDIE_IT_SHIFT				5
-#define INT_STS_PWRHOLD_IT_MASK				0x10
-#define INT_STS_PWRHOLD_IT_SHIFT			4
+#define INT_STS_PWRHOLD_R_IT_MASK			0x10
+#define INT_STS_PWRHOLD_R_IT_SHIFT			4
 #define INT_STS_PWRON_LP_IT_MASK			0x08
 #define INT_STS_PWRON_LP_IT_SHIFT			3
 #define INT_STS_PWRON_IT_MASK				0x04
 #define INT_STS_PWRON_IT_SHIFT				2
 #define INT_STS_VMBHI_IT_MASK				0x02
 #define INT_STS_VMBHI_IT_SHIFT				1
-#define INT_STS_VMBDCH_IT_MASK				0x01
-#define INT_STS_VMBDCH_IT_SHIFT				0
+#define INT_STS_PWRHOLD_F_IT_MASK			0x01
+#define INT_STS_PWRHOLD_F_IT_SHIFT			0
 
 
 /*Register INT_MSK  (0x80) register.RegisterDescription */
@@ -599,16 +642,16 @@
 #define INT_MSK_RTC_ALARM_IT_MSK_SHIFT			6
 #define INT_MSK_HOTDIE_IT_MSK_MASK			0x20
 #define INT_MSK_HOTDIE_IT_MSK_SHIFT			5
-#define INT_MSK_PWRHOLD_IT_MSK_MASK			0x10
-#define INT_MSK_PWRHOLD_IT_MSK_SHIFT			4
+#define INT_MSK_PWRHOLD_R_IT_MSK_MASK			0x10
+#define INT_MSK_PWRHOLD_R_IT_MSK_SHIFT			4
 #define INT_MSK_PWRON_LP_IT_MSK_MASK			0x08
 #define INT_MSK_PWRON_LP_IT_MSK_SHIFT			3
 #define INT_MSK_PWRON_IT_MSK_MASK			0x04
 #define INT_MSK_PWRON_IT_MSK_SHIFT			2
 #define INT_MSK_VMBHI_IT_MSK_MASK			0x02
 #define INT_MSK_VMBHI_IT_MSK_SHIFT			1
-#define INT_MSK_VMBDCH_IT_MSK_MASK			0x01
-#define INT_MSK_VMBDCH_IT_MSK_SHIFT			0
+#define INT_MSK_PWRHOLD_F_IT_MSK_MASK			0x01
+#define INT_MSK_PWRHOLD_F_IT_MSK_SHIFT			0
 
 
 /*Register INT_STS2  (0x80) register.RegisterDescription */
@@ -650,6 +693,14 @@
 
 
 /*Register INT_STS3  (0x80) register.RegisterDescription */
+#define INT_STS3_PWRDN_IT_MASK				0x80
+#define INT_STS3_PWRDN_IT_SHIFT				7
+#define INT_STS3_VMBCH2_L_IT_MASK			0x40
+#define INT_STS3_VMBCH2_L_IT_SHIFT			6
+#define INT_STS3_VMBCH2_H_IT_MASK			0x20
+#define INT_STS3_VMBCH2_H_IT_SHIFT			5
+#define INT_STS3_WTCHDG_IT_MASK				0x10
+#define INT_STS3_WTCHDG_IT_SHIFT			4
 #define INT_STS3_GPIO5_F_IT_MASK			0x08
 #define INT_STS3_GPIO5_F_IT_SHIFT			3
 #define INT_STS3_GPIO5_R_IT_MASK			0x04
@@ -661,6 +712,14 @@
 
 
 /*Register INT_MSK3  (0x80) register.RegisterDescription */
+#define INT_MSK3_PWRDN_IT_MSK_MASK			0x80
+#define INT_MSK3_PWRDN_IT_MSK_SHIFT			7
+#define INT_MSK3_VMBCH2_L_IT_MSK_MASK			0x40
+#define INT_MSK3_VMBCH2_L_IT_MSK_SHIFT			6
+#define INT_MSK3_VMBCH2_H_IT_MSK_MASK			0x20
+#define INT_MSK3_VMBCH2_H_IT_MSK_SHIFT			5
+#define INT_MSK3_WTCHDG_IT_MSK_MASK			0x10
+#define INT_MSK3_WTCHDG_IT_MSK_SHIFT			4
 #define INT_MSK3_GPIO5_F_IT_MSK_MASK			0x08
 #define INT_MSK3_GPIO5_F_IT_MSK_SHIFT			3
 #define INT_MSK3_GPIO5_R_IT_MSK_MASK			0x04
@@ -721,34 +780,32 @@
 #define TPS65910_IRQ_GPIO_F				9
 #define TPS65910_NUM_IRQ				10
 
-#define TPS65911_IRQ_VBAT_VMBDCH			0
-#define TPS65911_IRQ_VBAT_VMBDCH2L			1
-#define TPS65911_IRQ_VBAT_VMBDCH2H			2
-#define TPS65911_IRQ_VBAT_VMHI				3
-#define TPS65911_IRQ_PWRON				4
-#define TPS65911_IRQ_PWRON_LP				5
-#define TPS65911_IRQ_PWRHOLD_F				6
-#define TPS65911_IRQ_PWRHOLD_R				7
-#define TPS65911_IRQ_HOTDIE				8
-#define TPS65911_IRQ_RTC_ALARM				9
-#define TPS65911_IRQ_RTC_PERIOD				10
-#define TPS65911_IRQ_GPIO0_R				11
-#define TPS65911_IRQ_GPIO0_F				12
-#define TPS65911_IRQ_GPIO1_R				13
-#define TPS65911_IRQ_GPIO1_F				14
-#define TPS65911_IRQ_GPIO2_R				15
-#define TPS65911_IRQ_GPIO2_F				16
-#define TPS65911_IRQ_GPIO3_R				17
-#define TPS65911_IRQ_GPIO3_F				18
-#define TPS65911_IRQ_GPIO4_R				19
-#define TPS65911_IRQ_GPIO4_F				20
-#define TPS65911_IRQ_GPIO5_R				21
-#define TPS65911_IRQ_GPIO5_F				22
-#define TPS65911_IRQ_WTCHDG				23
-#define TPS65911_IRQ_PWRDN				24
+#define TPS65911_IRQ_PWRHOLD_F				0
+#define TPS65911_IRQ_VBAT_VMHI				1
+#define TPS65911_IRQ_PWRON				2
+#define TPS65911_IRQ_PWRON_LP				3
+#define TPS65911_IRQ_PWRHOLD_R				4
+#define TPS65911_IRQ_HOTDIE				5
+#define TPS65911_IRQ_RTC_ALARM				6
+#define TPS65911_IRQ_RTC_PERIOD				7
+#define TPS65911_IRQ_GPIO0_R				8
+#define TPS65911_IRQ_GPIO0_F				9
+#define TPS65911_IRQ_GPIO1_R				10
+#define TPS65911_IRQ_GPIO1_F				11
+#define TPS65911_IRQ_GPIO2_R				12
+#define TPS65911_IRQ_GPIO2_F				13
+#define TPS65911_IRQ_GPIO3_R				14
+#define TPS65911_IRQ_GPIO3_F				15
+#define TPS65911_IRQ_GPIO4_R				16
+#define TPS65911_IRQ_GPIO4_F				17
+#define TPS65911_IRQ_GPIO5_R				18
+#define TPS65911_IRQ_GPIO5_F				19
+#define TPS65911_IRQ_WTCHDG				20
+#define TPS65911_IRQ_VMBCH2_H				21
+#define TPS65911_IRQ_VMBCH2_L				22
+#define TPS65911_IRQ_PWRDN				23
 
-#define TPS65911_NUM_IRQ				25
-
+#define TPS65911_NUM_IRQ				24
 
 /* GPIO Register Definitions */
 #define TPS65910_GPIO_DEB				BIT(2)
@@ -836,7 +893,6 @@
 	struct device *dev;
 	struct i2c_client *i2c_client;
 	struct regmap *regmap;
-	struct mutex io_mutex;
 	unsigned int id;
 
 	/* Client devices */
@@ -848,12 +904,8 @@
 	struct tps65910_board *of_plat_data;
 
 	/* IRQ Handling */
-	struct mutex irq_lock;
 	int chip_irq;
-	int irq_base;
-	int irq_num;
-	u32 irq_mask;
-	struct irq_domain *domain;
+	struct regmap_irq_chip_data *irq_data;
 };
 
 struct tps65910_platform_data {
@@ -861,10 +913,6 @@
 	int irq_base;
 };
 
-int tps65910_irq_init(struct tps65910 *tps65910, int irq,
-		struct tps65910_platform_data *pdata);
-int tps65910_irq_exit(struct tps65910 *tps65910);
-
 static inline int tps65910_chip_id(struct tps65910 *tps65910)
 {
 	return tps65910->id;
@@ -900,4 +948,9 @@
 	return regmap_update_bits(tps65910->regmap, reg, mask, val);
 }
 
+static inline int tps65910_irq_get_virq(struct tps65910 *tps65910, int irq)
+{
+	return regmap_irq_get_virq(tps65910->irq_data, irq);
+}
+
 #endif /*  __LINUX_MFD_TPS65910_H */
diff --git a/include/linux/mfd/tps80031.h b/include/linux/mfd/tps80031.h
new file mode 100644
index 0000000..2c75c9c
--- /dev/null
+++ b/include/linux/mfd/tps80031.h
@@ -0,0 +1,637 @@
+/*
+ * tps80031.h -- TI TPS80031 and TI TPS80032 PMIC driver.
+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <ldewangan@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */
+
+#ifndef __LINUX_MFD_TPS80031_H
+#define __LINUX_MFD_TPS80031_H
+
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+/* Pull-ups/Pull-downs */
+#define TPS80031_CFG_INPUT_PUPD1			0xF0
+#define TPS80031_CFG_INPUT_PUPD2			0xF1
+#define TPS80031_CFG_INPUT_PUPD3			0xF2
+#define TPS80031_CFG_INPUT_PUPD4			0xF3
+#define TPS80031_CFG_LDO_PD1				0xF4
+#define TPS80031_CFG_LDO_PD2				0xF5
+#define TPS80031_CFG_SMPS_PD				0xF6
+
+/* Real Time Clock */
+#define TPS80031_SECONDS_REG				0x00
+#define TPS80031_MINUTES_REG				0x01
+#define TPS80031_HOURS_REG				0x02
+#define TPS80031_DAYS_REG				0x03
+#define TPS80031_MONTHS_REG				0x04
+#define TPS80031_YEARS_REG				0x05
+#define TPS80031_WEEKS_REG				0x06
+#define TPS80031_ALARM_SECONDS_REG			0x08
+#define TPS80031_ALARM_MINUTES_REG			0x09
+#define TPS80031_ALARM_HOURS_REG			0x0A
+#define TPS80031_ALARM_DAYS_REG				0x0B
+#define TPS80031_ALARM_MONTHS_REG			0x0C
+#define TPS80031_ALARM_YEARS_REG			0x0D
+#define TPS80031_RTC_CTRL_REG				0x10
+#define TPS80031_RTC_STATUS_REG				0x11
+#define TPS80031_RTC_INTERRUPTS_REG			0x12
+#define TPS80031_RTC_COMP_LSB_REG			0x13
+#define TPS80031_RTC_COMP_MSB_REG			0x14
+#define TPS80031_RTC_RESET_STATUS_REG			0x16
+
+/*PMC Master Module */
+#define TPS80031_PHOENIX_START_CONDITION		0x1F
+#define TPS80031_PHOENIX_MSK_TRANSITION			0x20
+#define TPS80031_STS_HW_CONDITIONS			0x21
+#define TPS80031_PHOENIX_LAST_TURNOFF_STS		0x22
+#define TPS80031_VSYSMIN_LO_THRESHOLD			0x23
+#define TPS80031_VSYSMIN_HI_THRESHOLD			0x24
+#define TPS80031_PHOENIX_DEV_ON				0x25
+#define TPS80031_STS_PWR_GRP_STATE			0x27
+#define TPS80031_PH_CFG_VSYSLOW				0x28
+#define TPS80031_PH_STS_BOOT				0x29
+#define TPS80031_PHOENIX_SENS_TRANSITION		0x2A
+#define TPS80031_PHOENIX_SEQ_CFG			0x2B
+#define TPS80031_PRIMARY_WATCHDOG_CFG			0X2C
+#define TPS80031_KEY_PRESS_DUR_CFG			0X2D
+#define TPS80031_SMPS_LDO_SHORT_STS			0x2E
+
+/* PMC Slave Module - Broadcast */
+#define TPS80031_BROADCAST_ADDR_ALL			0x31
+#define TPS80031_BROADCAST_ADDR_REF			0x32
+#define TPS80031_BROADCAST_ADDR_PROV			0x33
+#define TPS80031_BROADCAST_ADDR_CLK_RST			0x34
+
+/* PMC Slave Module  SMPS Regulators */
+#define TPS80031_SMPS4_CFG_TRANS			0x41
+#define TPS80031_SMPS4_CFG_STATE			0x42
+#define TPS80031_SMPS4_CFG_VOLTAGE			0x44
+#define TPS80031_VIO_CFG_TRANS				0x47
+#define TPS80031_VIO_CFG_STATE				0x48
+#define TPS80031_VIO_CFG_FORCE				0x49
+#define TPS80031_VIO_CFG_VOLTAGE			0x4A
+#define TPS80031_VIO_CFG_STEP				0x48
+#define TPS80031_SMPS1_CFG_TRANS			0x53
+#define TPS80031_SMPS1_CFG_STATE			0x54
+#define TPS80031_SMPS1_CFG_FORCE			0x55
+#define TPS80031_SMPS1_CFG_VOLTAGE			0x56
+#define TPS80031_SMPS1_CFG_STEP				0x57
+#define TPS80031_SMPS2_CFG_TRANS			0x59
+#define TPS80031_SMPS2_CFG_STATE			0x5A
+#define TPS80031_SMPS2_CFG_FORCE			0x5B
+#define TPS80031_SMPS2_CFG_VOLTAGE			0x5C
+#define TPS80031_SMPS2_CFG_STEP				0x5D
+#define TPS80031_SMPS3_CFG_TRANS			0x65
+#define TPS80031_SMPS3_CFG_STATE			0x66
+#define TPS80031_SMPS3_CFG_VOLTAGE			0x68
+
+/* PMC Slave Module  LDO Regulators */
+#define TPS80031_VANA_CFG_TRANS				0x81
+#define TPS80031_VANA_CFG_STATE				0x82
+#define TPS80031_VANA_CFG_VOLTAGE			0x83
+#define TPS80031_LDO2_CFG_TRANS				0x85
+#define TPS80031_LDO2_CFG_STATE				0x86
+#define TPS80031_LDO2_CFG_VOLTAGE			0x87
+#define TPS80031_LDO4_CFG_TRANS				0x89
+#define TPS80031_LDO4_CFG_STATE				0x8A
+#define TPS80031_LDO4_CFG_VOLTAGE			0x8B
+#define TPS80031_LDO3_CFG_TRANS				0x8D
+#define TPS80031_LDO3_CFG_STATE				0x8E
+#define TPS80031_LDO3_CFG_VOLTAGE			0x8F
+#define TPS80031_LDO6_CFG_TRANS				0x91
+#define TPS80031_LDO6_CFG_STATE				0x92
+#define TPS80031_LDO6_CFG_VOLTAGE			0x93
+#define TPS80031_LDOLN_CFG_TRANS			0x95
+#define TPS80031_LDOLN_CFG_STATE			0x96
+#define TPS80031_LDOLN_CFG_VOLTAGE			0x97
+#define TPS80031_LDO5_CFG_TRANS				0x99
+#define TPS80031_LDO5_CFG_STATE				0x9A
+#define TPS80031_LDO5_CFG_VOLTAGE			0x9B
+#define TPS80031_LDO1_CFG_TRANS				0x9D
+#define TPS80031_LDO1_CFG_STATE				0x9E
+#define TPS80031_LDO1_CFG_VOLTAGE			0x9F
+#define TPS80031_LDOUSB_CFG_TRANS			0xA1
+#define TPS80031_LDOUSB_CFG_STATE			0xA2
+#define TPS80031_LDOUSB_CFG_VOLTAGE			0xA3
+#define TPS80031_LDO7_CFG_TRANS				0xA5
+#define TPS80031_LDO7_CFG_STATE				0xA6
+#define TPS80031_LDO7_CFG_VOLTAGE			0xA7
+
+/* PMC Slave Module  External Control */
+#define TPS80031_REGEN1_CFG_TRANS			0xAE
+#define TPS80031_REGEN1_CFG_STATE			0xAF
+#define TPS80031_REGEN2_CFG_TRANS			0xB1
+#define TPS80031_REGEN2_CFG_STATE			0xB2
+#define TPS80031_SYSEN_CFG_TRANS			0xB4
+#define TPS80031_SYSEN_CFG_STATE			0xB5
+
+/* PMC Slave Module  Internal Control */
+#define TPS80031_NRESPWRON_CFG_TRANS			0xB7
+#define TPS80031_NRESPWRON_CFG_STATE			0xB8
+#define TPS80031_CLK32KAO_CFG_TRANS			0xBA
+#define TPS80031_CLK32KAO_CFG_STATE			0xBB
+#define TPS80031_CLK32KG_CFG_TRANS			0xBD
+#define TPS80031_CLK32KG_CFG_STATE			0xBE
+#define TPS80031_CLK32KAUDIO_CFG_TRANS			0xC0
+#define TPS80031_CLK32KAUDIO_CFG_STATE			0xC1
+#define TPS80031_VRTC_CFG_TRANS				0xC3
+#define TPS80031_VRTC_CFG_STATE				0xC4
+#define TPS80031_BIAS_CFG_TRANS				0xC6
+#define TPS80031_BIAS_CFG_STATE				0xC7
+#define TPS80031_VSYSMIN_HI_CFG_TRANS			0xC9
+#define TPS80031_VSYSMIN_HI_CFG_STATE			0xCA
+#define TPS80031_RC6MHZ_CFG_TRANS			0xCC
+#define TPS80031_RC6MHZ_CFG_STATE			0xCD
+#define TPS80031_TMP_CFG_TRANS				0xCF
+#define TPS80031_TMP_CFG_STATE				0xD0
+
+/* PMC Slave Module  resources assignment */
+#define TPS80031_PREQ1_RES_ASS_A			0xD7
+#define TPS80031_PREQ1_RES_ASS_B			0xD8
+#define TPS80031_PREQ1_RES_ASS_C			0xD9
+#define TPS80031_PREQ2_RES_ASS_A			0xDA
+#define TPS80031_PREQ2_RES_ASS_B			0xDB
+#define TPS80031_PREQ2_RES_ASS_C			0xDC
+#define TPS80031_PREQ3_RES_ASS_A			0xDD
+#define TPS80031_PREQ3_RES_ASS_B			0xDE
+#define TPS80031_PREQ3_RES_ASS_C			0xDF
+
+/* PMC Slave Module  Miscellaneous */
+#define TPS80031_SMPS_OFFSET				0xE0
+#define TPS80031_SMPS_MULT				0xE3
+#define TPS80031_MISC1					0xE4
+#define TPS80031_MISC2					0xE5
+#define TPS80031_BBSPOR_CFG				0xE6
+#define TPS80031_TMP_CFG				0xE7
+
+/* Battery Charging Controller and Indicator LED */
+#define TPS80031_CONTROLLER_CTRL2			0xDA
+#define TPS80031_CONTROLLER_VSEL_COMP			0xDB
+#define TPS80031_CHARGERUSB_VSYSREG			0xDC
+#define TPS80031_CHARGERUSB_VICHRG_PC			0xDD
+#define TPS80031_LINEAR_CHRG_STS			0xDE
+#define TPS80031_CONTROLLER_INT_MASK			0xE0
+#define TPS80031_CONTROLLER_CTRL1			0xE1
+#define TPS80031_CONTROLLER_WDG				0xE2
+#define TPS80031_CONTROLLER_STAT1			0xE3
+#define TPS80031_CHARGERUSB_INT_STATUS			0xE4
+#define TPS80031_CHARGERUSB_INT_MASK			0xE5
+#define TPS80031_CHARGERUSB_STATUS_INT1			0xE6
+#define TPS80031_CHARGERUSB_STATUS_INT2			0xE7
+#define TPS80031_CHARGERUSB_CTRL1			0xE8
+#define TPS80031_CHARGERUSB_CTRL2			0xE9
+#define TPS80031_CHARGERUSB_CTRL3			0xEA
+#define TPS80031_CHARGERUSB_STAT1			0xEB
+#define TPS80031_CHARGERUSB_VOREG			0xEC
+#define TPS80031_CHARGERUSB_VICHRG			0xED
+#define TPS80031_CHARGERUSB_CINLIMIT			0xEE
+#define TPS80031_CHARGERUSB_CTRLLIMIT1			0xEF
+#define TPS80031_CHARGERUSB_CTRLLIMIT2			0xF0
+#define TPS80031_LED_PWM_CTRL1				0xF4
+#define TPS80031_LED_PWM_CTRL2				0xF5
+
+/* USB On-The-Go  */
+#define TPS80031_BACKUP_REG				0xFA
+#define TPS80031_USB_VENDOR_ID_LSB			0x00
+#define TPS80031_USB_VENDOR_ID_MSB			0x01
+#define TPS80031_USB_PRODUCT_ID_LSB			0x02
+#define TPS80031_USB_PRODUCT_ID_MSB			0x03
+#define TPS80031_USB_VBUS_CTRL_SET			0x04
+#define TPS80031_USB_VBUS_CTRL_CLR			0x05
+#define TPS80031_USB_ID_CTRL_SET			0x06
+#define TPS80031_USB_ID_CTRL_CLR			0x07
+#define TPS80031_USB_VBUS_INT_SRC			0x08
+#define TPS80031_USB_VBUS_INT_LATCH_SET			0x09
+#define TPS80031_USB_VBUS_INT_LATCH_CLR			0x0A
+#define TPS80031_USB_VBUS_INT_EN_LO_SET			0x0B
+#define TPS80031_USB_VBUS_INT_EN_LO_CLR			0x0C
+#define TPS80031_USB_VBUS_INT_EN_HI_SET			0x0D
+#define TPS80031_USB_VBUS_INT_EN_HI_CLR			0x0E
+#define TPS80031_USB_ID_INT_SRC				0x0F
+#define TPS80031_USB_ID_INT_LATCH_SET			0x10
+#define TPS80031_USB_ID_INT_LATCH_CLR			0x11
+#define TPS80031_USB_ID_INT_EN_LO_SET			0x12
+#define TPS80031_USB_ID_INT_EN_LO_CLR			0x13
+#define TPS80031_USB_ID_INT_EN_HI_SET			0x14
+#define TPS80031_USB_ID_INT_EN_HI_CLR			0x15
+#define TPS80031_USB_OTG_ADP_CTRL			0x16
+#define TPS80031_USB_OTG_ADP_HIGH			0x17
+#define TPS80031_USB_OTG_ADP_LOW			0x18
+#define TPS80031_USB_OTG_ADP_RISE			0x19
+#define TPS80031_USB_OTG_REVISION			0x1A
+
+/* Gas Gauge */
+#define TPS80031_FG_REG_00				0xC0
+#define TPS80031_FG_REG_01				0xC1
+#define TPS80031_FG_REG_02				0xC2
+#define TPS80031_FG_REG_03				0xC3
+#define TPS80031_FG_REG_04				0xC4
+#define TPS80031_FG_REG_05				0xC5
+#define TPS80031_FG_REG_06				0xC6
+#define TPS80031_FG_REG_07				0xC7
+#define TPS80031_FG_REG_08				0xC8
+#define TPS80031_FG_REG_09				0xC9
+#define TPS80031_FG_REG_10				0xCA
+#define TPS80031_FG_REG_11				0xCB
+
+/* General Purpose ADC */
+#define TPS80031_GPADC_CTRL				0x2E
+#define TPS80031_GPADC_CTRL2				0x2F
+#define TPS80031_RTSELECT_LSB				0x32
+#define TPS80031_RTSELECT_ISB				0x33
+#define TPS80031_RTSELECT_MSB				0x34
+#define TPS80031_GPSELECT_ISB				0x35
+#define TPS80031_CTRL_P1				0x36
+#define TPS80031_RTCH0_LSB				0x37
+#define TPS80031_RTCH0_MSB				0x38
+#define TPS80031_RTCH1_LSB				0x39
+#define TPS80031_RTCH1_MSB				0x3A
+#define TPS80031_GPCH0_LSB				0x3B
+#define TPS80031_GPCH0_MSB				0x3C
+
+/* SIM, MMC and Battery Detection */
+#define TPS80031_SIMDEBOUNCING				0xEB
+#define TPS80031_SIMCTRL				0xEC
+#define TPS80031_MMCDEBOUNCING				0xED
+#define TPS80031_MMCCTRL				0xEE
+#define TPS80031_BATDEBOUNCING				0xEF
+
+/* Vibrator Driver and PWMs */
+#define TPS80031_VIBCTRL				0x9B
+#define TPS80031_VIBMODE				0x9C
+#define TPS80031_PWM1ON					0xBA
+#define TPS80031_PWM1OFF				0xBB
+#define TPS80031_PWM2ON					0xBD
+#define TPS80031_PWM2OFF				0xBE
+
+/* Control Interface */
+#define TPS80031_INT_STS_A				0xD0
+#define TPS80031_INT_STS_B				0xD1
+#define TPS80031_INT_STS_C				0xD2
+#define TPS80031_INT_MSK_LINE_A				0xD3
+#define TPS80031_INT_MSK_LINE_B				0xD4
+#define TPS80031_INT_MSK_LINE_C				0xD5
+#define TPS80031_INT_MSK_STS_A				0xD6
+#define TPS80031_INT_MSK_STS_B				0xD7
+#define TPS80031_INT_MSK_STS_C				0xD8
+#define TPS80031_TOGGLE1				0x90
+#define TPS80031_TOGGLE2				0x91
+#define TPS80031_TOGGLE3				0x92
+#define TPS80031_PWDNSTATUS1				0x93
+#define TPS80031_PWDNSTATUS2				0x94
+#define TPS80031_VALIDITY0				0x17
+#define TPS80031_VALIDITY1				0x18
+#define TPS80031_VALIDITY2				0x19
+#define TPS80031_VALIDITY3				0x1A
+#define TPS80031_VALIDITY4				0x1B
+#define TPS80031_VALIDITY5				0x1C
+#define TPS80031_VALIDITY6				0x1D
+#define TPS80031_VALIDITY7				0x1E
+
+/* Version number related register */
+#define TPS80031_JTAGVERNUM				0x87
+#define TPS80031_EPROM_REV				0xDF
+
+/* GPADC Trimming Bits. */
+#define TPS80031_GPADC_TRIM0				0xCC
+#define TPS80031_GPADC_TRIM1				0xCD
+#define TPS80031_GPADC_TRIM2				0xCE
+#define TPS80031_GPADC_TRIM3				0xCF
+#define TPS80031_GPADC_TRIM4				0xD0
+#define TPS80031_GPADC_TRIM5				0xD1
+#define TPS80031_GPADC_TRIM6				0xD2
+#define TPS80031_GPADC_TRIM7				0xD3
+#define TPS80031_GPADC_TRIM8				0xD4
+#define TPS80031_GPADC_TRIM9				0xD5
+#define TPS80031_GPADC_TRIM10				0xD6
+#define TPS80031_GPADC_TRIM11				0xD7
+#define TPS80031_GPADC_TRIM12				0xD8
+#define TPS80031_GPADC_TRIM13				0xD9
+#define TPS80031_GPADC_TRIM14				0xDA
+#define TPS80031_GPADC_TRIM15				0xDB
+#define TPS80031_GPADC_TRIM16				0xDC
+#define TPS80031_GPADC_TRIM17				0xDD
+#define TPS80031_GPADC_TRIM18				0xDE
+
+/* TPS80031_CONTROLLER_STAT1 bit fields */
+#define TPS80031_CONTROLLER_STAT1_BAT_TEMP		0
+#define TPS80031_CONTROLLER_STAT1_BAT_REMOVED		1
+#define TPS80031_CONTROLLER_STAT1_VBUS_DET		2
+#define TPS80031_CONTROLLER_STAT1_VAC_DET		3
+#define TPS80031_CONTROLLER_STAT1_FAULT_WDG		4
+#define TPS80031_CONTROLLER_STAT1_LINCH_GATED		6
+/* TPS80031_CONTROLLER_INT_MASK bit filed */
+#define TPS80031_CONTROLLER_INT_MASK_MVAC_DET		0
+#define TPS80031_CONTROLLER_INT_MASK_MVBUS_DET		1
+#define TPS80031_CONTROLLER_INT_MASK_MBAT_TEMP		2
+#define TPS80031_CONTROLLER_INT_MASK_MFAULT_WDG		3
+#define TPS80031_CONTROLLER_INT_MASK_MBAT_REMOVED	4
+#define TPS80031_CONTROLLER_INT_MASK_MLINCH_GATED	5
+
+#define TPS80031_CHARGE_CONTROL_SUB_INT_MASK		0x3F
+
+/* TPS80031_PHOENIX_DEV_ON bit field */
+#define TPS80031_DEVOFF					0x1
+
+#define TPS80031_EXT_CONTROL_CFG_TRANS			0
+#define TPS80031_EXT_CONTROL_CFG_STATE			1
+
+/* State register field */
+#define TPS80031_STATE_OFF				0x00
+#define TPS80031_STATE_ON				0x01
+#define TPS80031_STATE_MASK				0x03
+
+/* Trans register field */
+#define TPS80031_TRANS_ACTIVE_OFF			0x00
+#define TPS80031_TRANS_ACTIVE_ON			0x01
+#define TPS80031_TRANS_ACTIVE_MASK			0x03
+#define TPS80031_TRANS_SLEEP_OFF			0x00
+#define TPS80031_TRANS_SLEEP_ON				0x04
+#define TPS80031_TRANS_SLEEP_MASK			0x0C
+#define TPS80031_TRANS_OFF_OFF				0x00
+#define TPS80031_TRANS_OFF_ACTIVE			0x10
+#define TPS80031_TRANS_OFF_MASK				0x30
+
+#define TPS80031_EXT_PWR_REQ		(TPS80031_PWR_REQ_INPUT_PREQ1 | \
+					TPS80031_PWR_REQ_INPUT_PREQ2 | \
+					TPS80031_PWR_REQ_INPUT_PREQ3)
+
+/* TPS80031_BBSPOR_CFG bit field */
+#define TPS80031_BBSPOR_CHG_EN				0x8
+#define TPS80031_MAX_REGISTER				0xFF
+
+struct i2c_client;
+
+/* Supported chips */
+enum chips {
+	TPS80031 = 0x00000001,
+	TPS80032 = 0x00000002,
+};
+
+enum {
+	TPS80031_INT_PWRON,
+	TPS80031_INT_RPWRON,
+	TPS80031_INT_SYS_VLOW,
+	TPS80031_INT_RTC_ALARM,
+	TPS80031_INT_RTC_PERIOD,
+	TPS80031_INT_HOT_DIE,
+	TPS80031_INT_VXX_SHORT,
+	TPS80031_INT_SPDURATION,
+	TPS80031_INT_WATCHDOG,
+	TPS80031_INT_BAT,
+	TPS80031_INT_SIM,
+	TPS80031_INT_MMC,
+	TPS80031_INT_RES,
+	TPS80031_INT_GPADC_RT,
+	TPS80031_INT_GPADC_SW2_EOC,
+	TPS80031_INT_CC_AUTOCAL,
+	TPS80031_INT_ID_WKUP,
+	TPS80031_INT_VBUSS_WKUP,
+	TPS80031_INT_ID,
+	TPS80031_INT_VBUS,
+	TPS80031_INT_CHRG_CTRL,
+	TPS80031_INT_EXT_CHRG,
+	TPS80031_INT_INT_CHRG,
+	TPS80031_INT_RES2,
+	TPS80031_INT_BAT_TEMP_OVRANGE,
+	TPS80031_INT_BAT_REMOVED,
+	TPS80031_INT_VBUS_DET,
+	TPS80031_INT_VAC_DET,
+	TPS80031_INT_FAULT_WDG,
+	TPS80031_INT_LINCH_GATED,
+
+	/* Last interrupt id to get the end number */
+	TPS80031_INT_NR,
+};
+
+/* TPS80031 Slave IDs */
+#define TPS80031_NUM_SLAVES				4
+#define TPS80031_SLAVE_ID0				0
+#define TPS80031_SLAVE_ID1				1
+#define TPS80031_SLAVE_ID2				2
+#define TPS80031_SLAVE_ID3				3
+
+/* TPS80031 I2C addresses */
+#define TPS80031_I2C_ID0_ADDR				0x12
+#define TPS80031_I2C_ID1_ADDR				0x48
+#define TPS80031_I2C_ID2_ADDR				0x49
+#define TPS80031_I2C_ID3_ADDR				0x4A
+
+enum {
+	TPS80031_REGULATOR_VIO,
+	TPS80031_REGULATOR_SMPS1,
+	TPS80031_REGULATOR_SMPS2,
+	TPS80031_REGULATOR_SMPS3,
+	TPS80031_REGULATOR_SMPS4,
+	TPS80031_REGULATOR_VANA,
+	TPS80031_REGULATOR_LDO1,
+	TPS80031_REGULATOR_LDO2,
+	TPS80031_REGULATOR_LDO3,
+	TPS80031_REGULATOR_LDO4,
+	TPS80031_REGULATOR_LDO5,
+	TPS80031_REGULATOR_LDO6,
+	TPS80031_REGULATOR_LDO7,
+	TPS80031_REGULATOR_LDOLN,
+	TPS80031_REGULATOR_LDOUSB,
+	TPS80031_REGULATOR_VBUS,
+	TPS80031_REGULATOR_REGEN1,
+	TPS80031_REGULATOR_REGEN2,
+	TPS80031_REGULATOR_SYSEN,
+	TPS80031_REGULATOR_MAX,
+};
+
+/* Different configurations for the rails */
+enum {
+	/* USBLDO input selection */
+	TPS80031_USBLDO_INPUT_VSYS		= 0x00000001,
+	TPS80031_USBLDO_INPUT_PMID		= 0x00000002,
+
+	/* LDO3 output mode */
+	TPS80031_LDO3_OUTPUT_VIB		= 0x00000004,
+
+	/* VBUS configuration */
+	TPS80031_VBUS_DISCHRG_EN_PDN		= 0x00000004,
+	TPS80031_VBUS_SW_ONLY			= 0x00000008,
+	TPS80031_VBUS_SW_N_ID			= 0x00000010,
+};
+
+/* External controls requests */
+enum tps80031_ext_control {
+	TPS80031_PWR_REQ_INPUT_NONE		= 0x00000000,
+	TPS80031_PWR_REQ_INPUT_PREQ1		= 0x00000001,
+	TPS80031_PWR_REQ_INPUT_PREQ2		= 0x00000002,
+	TPS80031_PWR_REQ_INPUT_PREQ3		= 0x00000004,
+	TPS80031_PWR_OFF_ON_SLEEP		= 0x00000008,
+	TPS80031_PWR_ON_ON_SLEEP		= 0x00000010,
+};
+
+enum tps80031_pupd_pins {
+	TPS80031_PREQ1 = 0,
+	TPS80031_PREQ2A,
+	TPS80031_PREQ2B,
+	TPS80031_PREQ2C,
+	TPS80031_PREQ3,
+	TPS80031_NRES_WARM,
+	TPS80031_PWM_FORCE,
+	TPS80031_CHRG_EXT_CHRG_STATZ,
+	TPS80031_SIM,
+	TPS80031_MMC,
+	TPS80031_GPADC_START,
+	TPS80031_DVSI2C_SCL,
+	TPS80031_DVSI2C_SDA,
+	TPS80031_CTLI2C_SCL,
+	TPS80031_CTLI2C_SDA,
+};
+
+enum tps80031_pupd_settings {
+	TPS80031_PUPD_NORMAL,
+	TPS80031_PUPD_PULLDOWN,
+	TPS80031_PUPD_PULLUP,
+};
+
+struct tps80031 {
+	struct device		*dev;
+	unsigned long		chip_info;
+	int			es_version;
+	struct i2c_client	*clients[TPS80031_NUM_SLAVES];
+	struct regmap		*regmap[TPS80031_NUM_SLAVES];
+	struct regmap_irq_chip_data *irq_data;
+};
+
+struct tps80031_pupd_init_data {
+	int input_pin;
+	int setting;
+};
+
+/*
+ * struct tps80031_regulator_platform_data - tps80031 regulator platform data.
+ *
+ * @reg_init_data: The regulator init data.
+ * @ext_ctrl_flag: External control flag for sleep/power request control.
+ * @config_flags: Configuration flag to configure the rails.
+ *		  It should be ORed of config enums.
+ */
+
+struct tps80031_regulator_platform_data {
+	struct regulator_init_data *reg_init_data;
+	unsigned int ext_ctrl_flag;
+	unsigned int config_flags;
+};
+
+struct tps80031_platform_data {
+	int irq_base;
+	bool use_power_off;
+	struct tps80031_pupd_init_data *pupd_init_data;
+	int pupd_init_data_size;
+	struct tps80031_regulator_platform_data
+			*regulator_pdata[TPS80031_REGULATOR_MAX];
+};
+
+static inline int tps80031_write(struct device *dev, int sid,
+		int reg, uint8_t val)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_write(tps80031->regmap[sid], reg, val);
+}
+
+static inline int tps80031_writes(struct device *dev, int sid, int reg,
+		int len, uint8_t *val)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_bulk_write(tps80031->regmap[sid], reg, val, len);
+}
+
+static inline int tps80031_read(struct device *dev, int sid,
+		int reg, uint8_t *val)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+	unsigned int ival;
+	int ret;
+
+	ret = regmap_read(tps80031->regmap[sid], reg, &ival);
+	if (ret < 0) {
+		dev_err(dev, "failed reading from reg 0x%02x\n", reg);
+		return ret;
+	}
+
+	*val = ival;
+	return ret;
+}
+
+static inline int tps80031_reads(struct device *dev, int sid,
+		int reg, int len, uint8_t *val)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_bulk_read(tps80031->regmap[sid], reg, val, len);
+}
+
+static inline int tps80031_set_bits(struct device *dev, int sid,
+		int reg, uint8_t bit_mask)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_update_bits(tps80031->regmap[sid], reg,
+				bit_mask, bit_mask);
+}
+
+static inline int tps80031_clr_bits(struct device *dev, int sid,
+		int reg, uint8_t bit_mask)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_update_bits(tps80031->regmap[sid], reg, bit_mask, 0);
+}
+
+static inline int tps80031_update(struct device *dev, int sid,
+		int reg, uint8_t val, uint8_t mask)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_update_bits(tps80031->regmap[sid], reg, mask, val);
+}
+
+static inline unsigned long tps80031_get_chip_info(struct device *dev)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return tps80031->chip_info;
+}
+
+static inline int tps80031_get_pmu_version(struct device *dev)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return tps80031->es_version;
+}
+
+static inline int tps80031_irq_get_virq(struct device *dev, int irq)
+{
+	struct tps80031 *tps80031 = dev_get_drvdata(dev);
+
+	return regmap_irq_get_virq(tps80031->irq_data, irq);
+}
+
+extern int tps80031_ext_power_req_config(struct device *dev,
+		unsigned long ext_ctrl_flag, int preq_bit,
+		int state_reg_add, int trans_reg_add);
+#endif /*__LINUX_MFD_TPS80031_H */
diff --git a/include/linux/mfd/twl6040.h b/include/linux/mfd/twl6040.h
index a8eff4a..94ac944 100644
--- a/include/linux/mfd/twl6040.h
+++ b/include/linux/mfd/twl6040.h
@@ -207,10 +207,12 @@
 };
 
 struct regmap;
+struct regmap_irq_chips_data;
 
 struct twl6040 {
 	struct device *dev;
 	struct regmap *regmap;
+	struct regmap_irq_chip_data *irq_data;
 	struct regulator_bulk_data supplies[2]; /* supplies for vio, v2v1 */
 	struct mutex mutex;
 	struct mutex irq_mutex;
@@ -228,9 +230,8 @@
 	unsigned int mclk;
 
 	unsigned int irq;
-	unsigned int irq_base;
-	u8 irq_masks_cur;
-	u8 irq_masks_cache;
+	unsigned int irq_ready;
+	unsigned int irq_th;
 };
 
 int twl6040_reg_read(struct twl6040 *twl6040, unsigned int reg);
@@ -245,8 +246,7 @@
 		    unsigned int freq_in, unsigned int freq_out);
 int twl6040_get_pll(struct twl6040 *twl6040);
 unsigned int twl6040_get_sysclk(struct twl6040 *twl6040);
-int twl6040_irq_init(struct twl6040 *twl6040);
-void twl6040_irq_exit(struct twl6040 *twl6040);
+
 /* Get the combined status of the vibra control register */
 int twl6040_get_vibralr_status(struct twl6040 *twl6040);
 
diff --git a/include/linux/mfd/viperboard.h b/include/linux/mfd/viperboard.h
new file mode 100644
index 0000000..1934528
--- /dev/null
+++ b/include/linux/mfd/viperboard.h
@@ -0,0 +1,110 @@
+/*
+ *  include/linux/mfd/viperboard.h
+ *
+ *  Nano River Technologies viperboard definitions
+ *
+ *  (C) 2012 by Lemonage GmbH
+ *  Author: Lars Poeschel <poeschel@lemonage.de>
+ *  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#ifndef __MFD_VIPERBOARD_H__
+#define __MFD_VIPERBOARD_H__
+
+#include <linux/types.h>
+#include <linux/usb.h>
+
+#define VPRBRD_EP_OUT               0x02
+#define VPRBRD_EP_IN                0x86
+
+#define VPRBRD_I2C_MSG_LEN          512 /* max length of a msg on USB level */
+
+#define VPRBRD_I2C_FREQ_6MHZ        1                        /*   6 MBit/s */
+#define VPRBRD_I2C_FREQ_3MHZ        2                        /*   3 MBit/s */
+#define VPRBRD_I2C_FREQ_1MHZ        3                        /*   1 MBit/s */
+#define VPRBRD_I2C_FREQ_FAST        4                        /* 400 kbit/s */
+#define VPRBRD_I2C_FREQ_400KHZ      VPRBRD_I2C_FREQ_FAST
+#define VPRBRD_I2C_FREQ_200KHZ      5                        /* 200 kbit/s */
+#define VPRBRD_I2C_FREQ_STD         6                        /* 100 kbit/s */
+#define VPRBRD_I2C_FREQ_100KHZ      VPRBRD_I2C_FREQ_STD
+#define VPRBRD_I2C_FREQ_10KHZ       7                        /*  10 kbit/s */
+
+#define VPRBRD_I2C_CMD_WRITE        0x00
+#define VPRBRD_I2C_CMD_READ         0x01
+#define VPRBRD_I2C_CMD_ADDR         0x02
+
+#define VPRBRD_USB_TYPE_OUT	    0x40
+#define VPRBRD_USB_TYPE_IN	    0xc0
+#define VPRBRD_USB_TIMEOUT_MS       100
+#define VPRBRD_USB_REQUEST_I2C_FREQ 0xe6
+#define VPRBRD_USB_REQUEST_I2C      0xe9
+#define VPRBRD_USB_REQUEST_MAJOR    0xea
+#define VPRBRD_USB_REQUEST_MINOR    0xeb
+#define VPRBRD_USB_REQUEST_ADC      0xec
+#define VPRBRD_USB_REQUEST_GPIOA    0xed
+#define VPRBRD_USB_REQUEST_GPIOB    0xdd
+
+struct vprbrd_i2c_write_hdr {
+	u8 cmd;
+	u16 addr;
+	u8 len1;
+	u8 len2;
+	u8 last;
+	u8 chan;
+	u16 spi;
+} __packed;
+
+struct vprbrd_i2c_read_hdr {
+	u8 cmd;
+	u16 addr;
+	u8 len0;
+	u8 len1;
+	u8 len2;
+	u8 len3;
+	u8 len4;
+	u8 len5;
+	u16 tf1;                        /* transfer 1 length */
+	u16 tf2;                        /* transfer 2 length */
+} __packed;
+
+struct vprbrd_i2c_status {
+	u8 unknown[11];
+	u8 status;
+} __packed;
+
+struct vprbrd_i2c_write_msg {
+	struct vprbrd_i2c_write_hdr header;
+	u8 data[VPRBRD_I2C_MSG_LEN
+		- sizeof(struct vprbrd_i2c_write_hdr)];
+} __packed;
+
+struct vprbrd_i2c_read_msg {
+	struct vprbrd_i2c_read_hdr header;
+	u8 data[VPRBRD_I2C_MSG_LEN
+		- sizeof(struct vprbrd_i2c_read_hdr)];
+} __packed;
+
+struct vprbrd_i2c_addr_msg {
+	u8 cmd;
+	u8 addr;
+	u8 unknown1;
+	u16 len;
+	u8 unknown2;
+	u8 unknown3;
+} __packed;
+
+/* Structure to hold all device specific stuff */
+struct vprbrd {
+	struct usb_device *usb_dev; /* the usb device for this device */
+	struct mutex lock;
+	u8 buf[sizeof(struct vprbrd_i2c_write_msg)];
+	struct platform_device pdev;
+};
+
+#endif /* __MFD_VIPERBOARD_H__ */
diff --git a/include/linux/platform_data/ti_am335x_adc.h b/include/linux/platform_data/ti_am335x_adc.h
new file mode 100644
index 0000000..e41d583
--- /dev/null
+++ b/include/linux/platform_data/ti_am335x_adc.h
@@ -0,0 +1,14 @@
+#ifndef __LINUX_TI_AM335X_ADC_H
+#define __LINUX_TI_AM335X_ADC_H
+
+/**
+ * struct adc_data	ADC Input information
+ * @adc_channels:	Number of analog inputs
+ *			available for ADC.
+ */
+
+struct adc_data {
+	unsigned int adc_channels;
+};
+
+#endif