blob: 26ade8c0a9609629c8208ffe424d70b637f5733c [file] [log] [blame]
/*
* animeo_ip.dts - Device Tree file for Somfy Animeo IP Boards
*
* Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2 only.
*/
/dts-v1/;
#include "at91sam9260.dtsi"
/ {
model = "Somfy Animeo IP";
compatible = "somfy,animeo-ip", "atmel,at91sam9260", "atmel,at91sam9";
aliases {
serial0 = &usart1;
serial1 = &usart2;
serial2 = &usart0;
serial3 = &dbgu;
serial4 = &usart3;
serial5 = &uart0;
serial6 = &uart1;
};
chosen {
linux,stdout-path = &usart2;
};
memory {
reg = <0x20000000 0x4000000>;
};
clocks {
slow_xtal {
clock-frequency = <32768>;
};
main_xtal {
clock-frequency = <18432000>;
};
};
ahb {
apb {
usart0: serial@fffb0000 {
pinctrl-0 = <&pinctrl_usart0 &pinctrl_usart0_rts>;
linux,rs485-enabled-at-boot-time;
status = "okay";
};
usart1: serial@fffb4000 {
pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts>;
linux,rs485-enabled-at-boot-time;
status = "okay";
};
usart2: serial@fffb8000 {
pinctrl-0 = <&pinctrl_usart2>;
status = "okay";
};
macb0: ethernet@fffc4000 {
pinctrl-0 = <&pinctrl_macb_rmii &pinctrl_macb_rmii_mii>;
phy-mode = "mii";
status = "okay";
};
mmc0: mmc@fffa8000 {
pinctrl-0 = <&pinctrl_mmc0_clk
&pinctrl_mmc0_slot1_cmd_dat0
&pinctrl_mmc0_slot1_dat1_3>;
status = "okay";
slot@1 {
reg = <1>;
bus-width = <4>;
};
};
watchdog@fffffd40 {
status = "okay";
};
};
ebi: ebi@10000000 {
status = "okay";
nand_controller: nand-controller {
status = "okay";
pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>;
pinctrl-names = "default";
nand@3 {
reg = <0x3 0x0 0x800000>;
rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
label = "atmel_nand";
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
barebox@0 {
label = "barebox";
reg = <0x0 0x58000>;
};
u_boot_env@58000 {
label = "u_boot_env";
reg = <0x58000 0x8000>;
};
ubi@60000 {
label = "ubi";
reg = <0x60000 0x1FA0000>;
};
};
};
};
};
usb0: ohci@500000 {
num-ports = <2>;
atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
status = "okay";
};
};
leds {
compatible = "gpio-leds";
power_green {
label = "power_green";
gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
power_red {
label = "power_red";
gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
};
tx_green {
label = "tx_green";
gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
};
tx_red {
label = "tx_red";
gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
keyswitch_in {
label = "keyswitch_in";
gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
linux,code = <28>;
wakeup-source;
};
error_in {
label = "error_in";
gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
linux,code = <29>;
wakeup-source;
};
btn {
label = "btn";
gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
linux,code = <31>;
wakeup-source;
};
};
};