/*
 * Device Tree file for Marvell Armada 375 evaluation board
 * (DB-88F6720)
 *
 *  Copyright (C) 2014 Marvell
 *
 * Gregory CLEMENT <gregory.clement@free-electrons.com>
 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 *
 * This file is dual-licensed: you can use it either under the terms
 * of the GPL or the X11 license, at your option. Note that this dual
 * licensing only applies to this file, and not this project as a
 * whole.
 *
 *  a) This file is free software; you can redistribute it and/or
 *     modify it under the terms of the GNU General Public License as
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
 *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
 * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
 *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
 *     conditions:
 *
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
 */

/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-375.dtsi"

/ {
	model = "Marvell Armada 375 Development Board";
	compatible = "marvell,a375-db", "marvell,armada375";

	chosen {
		stdout-path = "serial0:115200n8";
	};

	memory@0 {
		device_type = "memory";
		reg = <0x00000000 0x40000000>; /* 1 GB */
	};

	soc {
		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
			  MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000
			  MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>;

	};
};
&pciec {
	status = "okay";
};

/*
 * The two PCIe units are accessible through
 * standard PCIe slots on the board.
 */
&pcie0 {
	/* Port 0, Lane 0 */
	status = "okay";
};

&pcie1 {
	/* Port 1, Lane 0 */
	status = "okay";
};


&spi0 {
	pinctrl-0 = <&spi0_pins>;
	pinctrl-names = "default";

	/*
	 * SPI conflicts with NAND, so we disable it here, and
	 * select NAND as the enabled device by default.
	 */

	status = "disabled";

	spi-flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "n25q128a13", "jedec,spi-nor";
		reg = <0>; /* Chip select 0 */
		spi-max-frequency = <108000000>;
	};
};

&i2c0 {
	status = "okay";
	clock-frequency = <100000>;
	pinctrl-0 = <&i2c0_pins>;
	pinctrl-names = "default";
};

&i2c1 {
	status = "okay";
	clock-frequency = <100000>;
	pinctrl-0 = <&i2c1_pins>;
	pinctrl-names = "default";
};

&uart0 {
	status = "okay";
};

&pinctrl {
	sdio_st_pins: sdio-st-pins {
		marvell,pins = "mpp44", "mpp45";
		marvell,function = "gpio";
	};
};

&sata {
	status = "okay";
	nr-ports = <2>;
};

&nand {
	pinctrl-0 = <&nand_pins>;
	pinctrl-names = "default";
	status = "okay";
	num-cs = <1>;
	marvell,nand-keep-config;
	marvell,nand-enable-arbiter;
	nand-on-flash-bbt;
	nand-ecc-strength = <4>;
	nand-ecc-step-size = <512>;

	partition@0 {
		label = "U-Boot";
		reg = <0 0x800000>;
	};
	partition@800000 {
		label = "Linux";
		reg = <0x800000 0x800000>;
	};
	partition@1000000 {
		label = "Filesystem";
		reg = <0x1000000 0x3f000000>;
	};
};

&usb1 {
	status = "okay";
};

&usb2 {
	status = "okay";
};

&sdio {
	pinctrl-0 = <&sdio_pins &sdio_st_pins>;
	pinctrl-names = "default";
	status = "okay";
	cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
	wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
};

&mdio {
	phy0: ethernet-phy@0 {
		reg = <0>;
	};

	phy3: ethernet-phy@3 {
		reg = <3>;
	};
};

&ethernet {
	status = "okay";
};


&eth0 {
	status = "okay";
	phy = <&phy0>;
	phy-mode = "rgmii-id";
};

&eth1 {
	status = "okay";
	phy = <&phy3>;
	phy-mode = "gmii";
};