blob: 39bc73db72e5da0d02d4a64c43a46e89ffc095c9 [file] [log] [blame]
/*
* Copyright 2015 Adam Sampson <ats@offog.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun7i-a20.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "LinkSprite pcDuino3 Nano";
compatible = "linksprite,pcduino3-nano", "allwinner,sun7i-a20";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_pcduino3_nano>;
/* Marked "LED3" on the PCB. */
usr1 {
label = "pcduino3-nano:green:usr1";
gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */
};
/* Marked "LED4" on the PCB. */
usr2 {
label = "pcduino3-nano:green:usr2";
gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */
};
};
};
&ahci {
target-supply = <&reg_ahci_5v>;
status = "okay";
};
&codec {
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
&ir0 {
pinctrl-names = "default";
pinctrl-0 = <&ir0_rx_pins_a>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&otg_sram {
status = "okay";
};
&pio {
ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
pins = "PH2";
function = "gpio_out";
};
led_pins_pcduino3_nano: led_pins@0 {
pins = "PH16", "PH15";
function = "gpio_out";
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
pins = "PH4";
function = "gpio_in";
bias-pull-up;
};
usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
pins = "PD2";
function = "gpio_out";
};
};
&reg_ahci_5v {
pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
#include "axp209.dtsi"
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-int-pll";
};
&reg_ldo1 {
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
/* A single regulator (U24) powers both USB host ports. */
&reg_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb1_vbus>;
status = "okay";
};