diff --git a/arch/arm/Kconfig-nommu b/arch/arm/Kconfig-nommu
index aed66d5..b757634 100644
--- a/arch/arm/Kconfig-nommu
+++ b/arch/arm/Kconfig-nommu
@@ -34,8 +34,7 @@
 	  used instead of the auto-probing which utilizes the register.
 
 config REMAP_VECTORS_TO_RAM
-	bool 'Install vectors to the beginning of RAM' if DRAM_BASE
-	depends on DRAM_BASE
+	bool 'Install vectors to the beginning of RAM'
 	help
 	  The kernel needs to change the hardware exception vectors.
 	  In nommu mode, the hardware exception vectors are normally
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index 76cbd9c..bee7511 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -111,6 +111,13 @@
 
 #endif /* !CONFIG_MMU */
 
+#ifdef CONFIG_XIP_KERNEL
+#define KERNEL_START		_sdata
+#else
+#define KERNEL_START		_stext
+#endif
+#define KERNEL_END		_end
+
 /*
  * We fix the TCM memories max 32 KiB ITCM resp DTCM at these
  * locations
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 34e3f3c..f4e5450 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -81,7 +81,7 @@ __setup("fpe=", fpe_setup);
 extern void init_default_cache_policy(unsigned long);
 extern void paging_init(const struct machine_desc *desc);
 extern void early_paging_init(const struct machine_desc *);
-extern void sanity_check_meminfo(void);
+extern void adjust_lowmem_bounds(void);
 extern enum reboot_mode reboot_mode;
 extern void setup_dma_zone(const struct machine_desc *desc);
 
@@ -1093,8 +1093,14 @@ void __init setup_arch(char **cmdline_p)
 	setup_dma_zone(mdesc);
 	xen_early_init();
 	efi_init();
-	sanity_check_meminfo();
+	/*
+	 * Make sure the calculation for lowmem/highmem is set appropriately
+	 * before reserving/allocating any mmeory
+	 */
+	adjust_lowmem_bounds();
 	arm_memblock_init(mdesc);
+	/* Memory may have been removed so recalculate the bounds. */
+	adjust_lowmem_bounds();
 
 	early_ioremap_reset();
 
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index ab77100..afa64ed 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -868,6 +868,9 @@ static int __arm_dma_mmap(struct device *dev, struct vm_area_struct *vma,
 				      vma->vm_end - vma->vm_start,
 				      vma->vm_page_prot);
 	}
+#else
+	ret = vm_iomap_memory(vma, vma->vm_start,
+			      (vma->vm_end - vma->vm_start));
 #endif	/* CONFIG_MMU */
 
 	return ret;
diff --git a/arch/arm/mm/flush.c b/arch/arm/mm/flush.c
index 3cced84..f1e6190 100644
--- a/arch/arm/mm/flush.c
+++ b/arch/arm/mm/flush.c
@@ -327,6 +327,12 @@ void flush_dcache_page(struct page *page)
 	if (page == ZERO_PAGE(0))
 		return;
 
+	if (!cache_ops_need_broadcast() && cache_is_vipt_nonaliasing()) {
+		if (test_bit(PG_dcache_clean, &page->flags))
+			clear_bit(PG_dcache_clean, &page->flags);
+		return;
+	}
+
 	mapping = page_mapping(page);
 
 	if (!cache_ops_need_broadcast() &&
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index 370581a..4127f57 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -230,11 +230,8 @@ phys_addr_t __init arm_memblock_steal(phys_addr_t size, phys_addr_t align)
 void __init arm_memblock_init(const struct machine_desc *mdesc)
 {
 	/* Register the kernel text, kernel data and initrd with memblock. */
-#ifdef CONFIG_XIP_KERNEL
-	memblock_reserve(__pa(_sdata), _end - _sdata);
-#else
-	memblock_reserve(__pa(_stext), _end - _stext);
-#endif
+	memblock_reserve(__pa(KERNEL_START), KERNEL_END - KERNEL_START);
+
 #ifdef CONFIG_BLK_DEV_INITRD
 	/* FDT scan will populate initrd_start */
 	if (initrd_start && !phys_initrd_size) {
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 4001dd1..4e016d7 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -1152,13 +1152,12 @@ early_param("vmalloc", early_vmalloc);
 
 phys_addr_t arm_lowmem_limit __initdata = 0;
 
-void __init sanity_check_meminfo(void)
+void __init adjust_lowmem_bounds(void)
 {
 	phys_addr_t memblock_limit = 0;
-	int highmem = 0;
 	u64 vmalloc_limit;
 	struct memblock_region *reg;
-	bool should_use_highmem = false;
+	phys_addr_t lowmem_limit = 0;
 
 	/*
 	 * Let's use our own (unoptimized) equivalent of __pa() that is
@@ -1172,43 +1171,18 @@ void __init sanity_check_meminfo(void)
 	for_each_memblock(memory, reg) {
 		phys_addr_t block_start = reg->base;
 		phys_addr_t block_end = reg->base + reg->size;
-		phys_addr_t size_limit = reg->size;
 
-		if (reg->base >= vmalloc_limit)
-			highmem = 1;
-		else
-			size_limit = vmalloc_limit - reg->base;
-
-
-		if (!IS_ENABLED(CONFIG_HIGHMEM) || cache_is_vipt_aliasing()) {
-
-			if (highmem) {
-				pr_notice("Ignoring RAM at %pa-%pa (!CONFIG_HIGHMEM)\n",
-					  &block_start, &block_end);
-				memblock_remove(reg->base, reg->size);
-				should_use_highmem = true;
-				continue;
-			}
-
-			if (reg->size > size_limit) {
-				phys_addr_t overlap_size = reg->size - size_limit;
-
-				pr_notice("Truncating RAM at %pa-%pa",
-					  &block_start, &block_end);
-				block_end = vmalloc_limit;
-				pr_cont(" to -%pa", &block_end);
-				memblock_remove(vmalloc_limit, overlap_size);
-				should_use_highmem = true;
-			}
-		}
-
-		if (!highmem) {
-			if (block_end > arm_lowmem_limit) {
-				if (reg->size > size_limit)
-					arm_lowmem_limit = vmalloc_limit;
-				else
-					arm_lowmem_limit = block_end;
-			}
+		if (reg->base < vmalloc_limit) {
+			if (block_end > lowmem_limit)
+				/*
+				 * Compare as u64 to ensure vmalloc_limit does
+				 * not get truncated. block_end should always
+				 * fit in phys_addr_t so there should be no
+				 * issue with assignment.
+				 */
+				lowmem_limit = min_t(u64,
+							 vmalloc_limit,
+							 block_end);
 
 			/*
 			 * Find the first non-pmd-aligned page, and point
@@ -1227,14 +1201,13 @@ void __init sanity_check_meminfo(void)
 				if (!IS_ALIGNED(block_start, PMD_SIZE))
 					memblock_limit = block_start;
 				else if (!IS_ALIGNED(block_end, PMD_SIZE))
-					memblock_limit = arm_lowmem_limit;
+					memblock_limit = lowmem_limit;
 			}
 
 		}
 	}
 
-	if (should_use_highmem)
-		pr_notice("Consider using a HIGHMEM enabled kernel.\n");
+	arm_lowmem_limit = lowmem_limit;
 
 	high_memory = __va(arm_lowmem_limit - 1) + 1;
 
@@ -1248,6 +1221,18 @@ void __init sanity_check_meminfo(void)
 	if (!memblock_limit)
 		memblock_limit = arm_lowmem_limit;
 
+	if (!IS_ENABLED(CONFIG_HIGHMEM) || cache_is_vipt_aliasing()) {
+		if (memblock_end_of_DRAM() > arm_lowmem_limit) {
+			phys_addr_t end = memblock_end_of_DRAM();
+
+			pr_notice("Ignoring RAM at %pa-%pa\n",
+				  &memblock_limit, &end);
+			pr_notice("Consider using a HIGHMEM enabled kernel.\n");
+
+			memblock_remove(memblock_limit, end - memblock_limit);
+		}
+	}
+
 	memblock_set_current_limit(memblock_limit);
 }
 
@@ -1437,11 +1422,7 @@ static void __init kmap_init(void)
 static void __init map_lowmem(void)
 {
 	struct memblock_region *reg;
-#ifdef CONFIG_XIP_KERNEL
-	phys_addr_t kernel_x_start = round_down(__pa(_sdata), SECTION_SIZE);
-#else
-	phys_addr_t kernel_x_start = round_down(__pa(_stext), SECTION_SIZE);
-#endif
+	phys_addr_t kernel_x_start = round_down(__pa(KERNEL_START), SECTION_SIZE);
 	phys_addr_t kernel_x_end = round_up(__pa(__init_end), SECTION_SIZE);
 
 	/* Map all the lowmem memory banks. */
diff --git a/arch/arm/mm/nommu.c b/arch/arm/mm/nommu.c
index 2740967..13a25d6 100644
--- a/arch/arm/mm/nommu.c
+++ b/arch/arm/mm/nommu.c
@@ -85,7 +85,7 @@ static unsigned long irbar_read(void)
 }
 
 /* MPU initialisation functions */
-void __init sanity_check_meminfo_mpu(void)
+void __init adjust_lowmem_bounds_mpu(void)
 {
 	phys_addr_t phys_offset = PHYS_OFFSET;
 	phys_addr_t aligned_region_size, specified_mem_size, rounded_mem_size;
@@ -274,7 +274,7 @@ void __init mpu_setup(void)
 	}
 }
 #else
-static void sanity_check_meminfo_mpu(void) {}
+static void adjust_lowmem_bounds_mpu(void) {}
 static void __init mpu_setup(void) {}
 #endif /* CONFIG_ARM_MPU */
 
@@ -295,10 +295,10 @@ void __init arm_mm_memblock_reserve(void)
 #endif
 }
 
-void __init sanity_check_meminfo(void)
+void __init adjust_lowmem_bounds(void)
 {
 	phys_addr_t end;
-	sanity_check_meminfo_mpu();
+	adjust_lowmem_bounds_mpu();
 	end = memblock_end_of_DRAM();
 	high_memory = __va(end - 1) + 1;
 	memblock_set_current_limit(end);
diff --git a/drivers/mtd/devices/lart.c b/drivers/mtd/devices/lart.c
index 82bd00a..268aae4 100644
--- a/drivers/mtd/devices/lart.c
+++ b/drivers/mtd/devices/lart.c
@@ -75,18 +75,18 @@ static char module_name[] = "lart";
 
 /* blob */
 #define NUM_BLOB_BLOCKS		FLASH_NUMBLOCKS_16m_PARAM
-#define BLOB_START			0x00000000
-#define BLOB_LEN			(NUM_BLOB_BLOCKS * FLASH_BLOCKSIZE_PARAM)
+#define PART_BLOB_START		0x00000000
+#define PART_BLOB_LEN		(NUM_BLOB_BLOCKS * FLASH_BLOCKSIZE_PARAM)
 
 /* kernel */
 #define NUM_KERNEL_BLOCKS	7
-#define KERNEL_START		(BLOB_START + BLOB_LEN)
-#define KERNEL_LEN			(NUM_KERNEL_BLOCKS * FLASH_BLOCKSIZE_MAIN)
+#define PART_KERNEL_START	(PART_BLOB_START + PART_BLOB_LEN)
+#define PART_KERNEL_LEN		(NUM_KERNEL_BLOCKS * FLASH_BLOCKSIZE_MAIN)
 
 /* initial ramdisk */
 #define NUM_INITRD_BLOCKS	24
-#define INITRD_START		(KERNEL_START + KERNEL_LEN)
-#define INITRD_LEN			(NUM_INITRD_BLOCKS * FLASH_BLOCKSIZE_MAIN)
+#define PART_INITRD_START	(PART_KERNEL_START + PART_KERNEL_LEN)
+#define PART_INITRD_LEN		(NUM_INITRD_BLOCKS * FLASH_BLOCKSIZE_MAIN)
 
 /*
  * See section 4.0 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
@@ -587,20 +587,20 @@ static struct mtd_partition lart_partitions[] = {
 	/* blob */
 	{
 		.name	= "blob",
-		.offset	= BLOB_START,
-		.size	= BLOB_LEN,
+		.offset	= PART_BLOB_START,
+		.size	= PART_BLOB_LEN,
 	},
 	/* kernel */
 	{
 		.name	= "kernel",
-		.offset	= KERNEL_START,		/* MTDPART_OFS_APPEND */
-		.size	= KERNEL_LEN,
+		.offset	= PART_KERNEL_START,	/* MTDPART_OFS_APPEND */
+		.size	= PART_KERNEL_LEN,
 	},
 	/* initial ramdisk / file system */
 	{
 		.name	= "file system",
-		.offset	= INITRD_START,		/* MTDPART_OFS_APPEND */
-		.size	= INITRD_LEN,		/* MTDPART_SIZ_FULL */
+		.offset	= PART_INITRD_START,	/* MTDPART_OFS_APPEND */
+		.size	= PART_INITRD_LEN,	/* MTDPART_SIZ_FULL */
 	}
 };
 #define NUM_PARTITIONS ARRAY_SIZE(lart_partitions)