| Analog Devices ADF4350/ADF4351 device driver | |
| Required properties: | |
| - compatible: Should be one of | |
| * "adi,adf4350": When using the ADF4350 device | |
| * "adi,adf4351": When using the ADF4351 device | |
| - reg: SPI chip select numbert for the device | |
| - spi-max-frequency: Max SPI frequency to use (< 20000000) | |
| - clocks: From common clock binding. Clock is phandle to clock for | |
| ADF435x Reference Clock (CLKIN). | |
| Optional properties: | |
| - gpios: GPIO Lock detect - If set with a valid phandle and GPIO number, | |
| pll lock state is tested upon read. | |
| - adi,channel-spacing: Channel spacing in Hz (influences MODULUS). | |
| - adi,power-up-frequency: If set in Hz the PLL tunes to | |
| the desired frequency on probe. | |
| - adi,reference-div-factor: If set the driver skips dynamic calculation | |
| and uses this default value instead. | |
| - adi,reference-doubler-enable: Enables reference doubler. | |
| - adi,reference-div2-enable: Enables reference divider. | |
| - adi,phase-detector-polarity-positive-enable: Enables positive phase | |
| detector polarity. Default = negative. | |
| - adi,lock-detect-precision-6ns-enable: Enables 6ns lock detect precision. | |
| Default = 10ns. | |
| - adi,lock-detect-function-integer-n-enable: Enables lock detect | |
| for integer-N mode. Default = factional-N mode. | |
| - adi,charge-pump-current: Charge pump current in mA. | |
| Default = 2500mA. | |
| - adi,muxout-select: On chip multiplexer output selection. | |
| Valid values for the multiplexer output are: | |
| 0: Three-State Output (default) | |
| 1: DVDD | |
| 2: DGND | |
| 3: R-Counter output | |
| 4: N-Divider output | |
| 5: Analog lock detect | |
| 6: Digital lock detect | |
| - adi,low-spur-mode-enable: Enables low spur mode. | |
| Default = Low noise mode. | |
| - adi,cycle-slip-reduction-enable: Enables cycle slip reduction. | |
| - adi,charge-cancellation-enable: Enabled charge pump | |
| charge cancellation for integer-N modes. | |
| - adi,anti-backlash-3ns-enable: Enables 3ns antibacklash pulse width | |
| for integer-N modes. | |
| - adi,band-select-clock-mode-high-enable: Enables faster band | |
| selection logic. | |
| - adi,12bit-clk-divider: Clock divider value used when | |
| adi,12bit-clkdiv-mode != 0 | |
| - adi,clk-divider-mode: | |
| Valid values for the clkdiv mode are: | |
| 0: Clock divider off (default) | |
| 1: Fast lock enable | |
| 2: Phase resync enable | |
| - adi,aux-output-enable: Enables auxiliary RF output. | |
| - adi,aux-output-fundamental-enable: Selects fundamental VCO output on | |
| the auxiliary RF output. Default = Output of RF dividers. | |
| - adi,mute-till-lock-enable: Enables Mute-Till-Lock-Detect function. | |
| - adi,output-power: Output power selection. | |
| Valid values for the power mode are: | |
| 0: -4dBm (default) | |
| 1: -1dBm | |
| 2: +2dBm | |
| 3: +5dBm | |
| - adi,aux-output-power: Auxiliary output power selection. | |
| Valid values for the power mode are: | |
| 0: -4dBm (default) | |
| 1: -1dBm | |
| 2: +2dBm | |
| 3: +5dBm | |
| Example: | |
| lo_pll0_rx_adf4351: adf4351-rx-lpc@4 { | |
| compatible = "adi,adf4351"; | |
| reg = <4>; | |
| spi-max-frequency = <10000000>; | |
| clocks = <&clk0_ad9523 9>; | |
| clock-names = "clkin"; | |
| adi,channel-spacing = <10000>; | |
| adi,power-up-frequency = <2400000000>; | |
| adi,phase-detector-polarity-positive-enable; | |
| adi,charge-pump-current = <2500>; | |
| adi,output-power = <3>; | |
| adi,mute-till-lock-enable; | |
| }; |