usb: musb: Remove try_idle for 2430 glue layer
This is no longer needed with PM runtime at least for 2430 glue.
We can now rely only on PM runtime and cable detection.
The other glue layers can probably remove try_idle too, but that
needs to be tested for each platform before doing it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index b81216d..5365394 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -57,92 +57,6 @@
static struct omap2430_glue *_glue;
-static struct timer_list musb_idle_timer;
-
-static void musb_do_idle(unsigned long _musb)
-{
- struct musb *musb = (void *)_musb;
- unsigned long flags;
- u8 power;
- u8 devctl;
-
- spin_lock_irqsave(&musb->lock, flags);
-
- switch (musb->xceiv->otg->state) {
- case OTG_STATE_A_WAIT_BCON:
-
- devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
- if (devctl & MUSB_DEVCTL_BDEVICE) {
- musb->xceiv->otg->state = OTG_STATE_B_IDLE;
- MUSB_DEV_MODE(musb);
- } else {
- musb->xceiv->otg->state = OTG_STATE_A_IDLE;
- MUSB_HST_MODE(musb);
- }
- break;
- case OTG_STATE_A_SUSPEND:
- /* finish RESUME signaling? */
- if (musb->port1_status & MUSB_PORT_STAT_RESUME) {
- power = musb_readb(musb->mregs, MUSB_POWER);
- power &= ~MUSB_POWER_RESUME;
- dev_dbg(musb->controller, "root port resume stopped, power %02x\n", power);
- musb_writeb(musb->mregs, MUSB_POWER, power);
- musb->is_active = 1;
- musb->port1_status &= ~(USB_PORT_STAT_SUSPEND
- | MUSB_PORT_STAT_RESUME);
- musb->port1_status |= USB_PORT_STAT_C_SUSPEND << 16;
- usb_hcd_poll_rh_status(musb->hcd);
- /* NOTE: it might really be A_WAIT_BCON ... */
- musb->xceiv->otg->state = OTG_STATE_A_HOST;
- }
- break;
- case OTG_STATE_A_HOST:
- devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
- if (devctl & MUSB_DEVCTL_BDEVICE)
- musb->xceiv->otg->state = OTG_STATE_B_IDLE;
- else
- musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
- default:
- break;
- }
- spin_unlock_irqrestore(&musb->lock, flags);
-}
-
-
-static void omap2430_musb_try_idle(struct musb *musb, unsigned long timeout)
-{
- unsigned long default_timeout = jiffies + msecs_to_jiffies(3);
- static unsigned long last_timer;
-
- if (timeout == 0)
- timeout = default_timeout;
-
- /* Never idle if active, or when VBUS timeout is not set as host */
- if (musb->is_active || ((musb->a_wait_bcon == 0)
- && (musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON))) {
- dev_dbg(musb->controller, "%s active, deleting timer\n",
- usb_otg_state_string(musb->xceiv->otg->state));
- del_timer(&musb_idle_timer);
- last_timer = jiffies;
- return;
- }
-
- if (time_after(last_timer, timeout)) {
- if (!timer_pending(&musb_idle_timer))
- last_timer = timeout;
- else {
- dev_dbg(musb->controller, "Longer idle timer already pending, ignoring\n");
- return;
- }
- }
- last_timer = timeout;
-
- dev_dbg(musb->controller, "%s inactive, for idle timer for %lu ms\n",
- usb_otg_state_string(musb->xceiv->otg->state),
- (unsigned long)jiffies_to_msecs(timeout - jiffies));
- mod_timer(&musb_idle_timer, timeout);
-}
-
static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
{
struct usb_otg *otg = musb->xceiv->otg;
@@ -467,8 +381,6 @@
musb_readl(musb->mregs, OTG_INTERFSEL),
musb_readl(musb->mregs, OTG_SIMENABLE));
- setup_timer(&musb_idle_timer, musb_do_idle, (unsigned long) musb);
-
if (glue->status != MUSB_UNKNOWN)
omap_musb_set_mailbox(glue);
@@ -543,7 +455,6 @@
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
- del_timer_sync(&musb_idle_timer);
omap2430_low_level_exit(musb);
phy_exit(musb->phy);
musb->phy = NULL;
@@ -562,8 +473,6 @@
.exit = omap2430_musb_exit,
.set_mode = omap2430_musb_set_mode,
- .try_idle = omap2430_musb_try_idle,
-
.set_vbus = omap2430_musb_set_vbus,
.enable = omap2430_musb_enable,
