Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt

* ROCKCHIP type-c PHY
---------------------

Required properties:
 - compatible : must be "rockchip,rk3399-typec-phy"
 - reg: Address and length of the usb phy control register set
 - rockchip,grf : phandle to the syscon managing the "general
   register files"
 - clocks : phandle + clock specifier for the phy clocks
 - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
 - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or
		    <&cru SCLK_UPHY1_TCPDCORE>;
 - assigned-clock-rates : the phy core clk frequency, shall be: 50000000
 - resets : a list of phandle + reset specifier pairs
 - reset-names : string reset name, must be:
		 "uphy", "uphy-pipe", "uphy-tcphy"
 - extcon : extcon specifier for the Power Delivery

Note, there are 2 type-c phys for RK3399, and they are almost identical, except
these registers(description below), every register node contains 3 sections:
offset, enable bit, write mask bit.
 - rockchip,typec-conn-dir : the register of type-c connector direction,
   for type-c phy0, it must be <0xe580 0 16>;
   for type-c phy1, it must be <0xe58c 0 16>;
 - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
   control.
   for type-c phy0, it must be <0xe580 3 19>;
   for type-c phy1, it must be <0xe58c 3 19>;
 - rockchip,external-psm : the register of type-c phy external psm clock
   selection.
   for type-c phy0, it must be <0xe588 14 30>;
   for type-c phy1, it must be <0xe594 14 30>;
 - rockchip,pipe-status : the register of type-c phy pipe status.
   for type-c phy0, it must be <0xe5c0 0 0>;
   for type-c phy1, it must be <0xe5c0 16 16>;

Required nodes : a sub-node is required for each port the phy provides.
		 The sub-node name is used to identify dp or usb3 port,
		 and shall be the following entries:
	* "dp-port" : the name of DP port.
	* "usb3-port" : the name of USB3 port.

Required properties (port (child) node):
- #phy-cells : must be 0, See ./phy-bindings.txt for details.

Example:
	tcphy0: phy@ff7c0000 {
		compatible = "rockchip,rk3399-typec-phy";
		reg = <0x0 0xff7c0000 0x0 0x40000>;
		rockchip,grf = <&grf>;
		extcon = <&fusb0>;
		clocks = <&cru SCLK_UPHY0_TCPDCORE>,
			 <&cru SCLK_UPHY0_TCPDPHY_REF>;
		clock-names = "tcpdcore", "tcpdphy-ref";
		assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
		assigned-clock-rates = <50000000>;
		resets = <&cru SRST_UPHY0>,
			 <&cru SRST_UPHY0_PIPE_L00>,
			 <&cru SRST_P_UPHY0_TCPHY>;
		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
		rockchip,typec-conn-dir = <0xe580 0 16>;
		rockchip,usb3tousb2-en = <0xe580 3 19>;
		rockchip,external-psm = <0xe588 14 30>;
		rockchip,pipe-status = <0xe5c0 0 0>;

		tcphy0_dp: dp-port {
			#phy-cells = <0>;
		};

		tcphy0_usb3: usb3-port {
			#phy-cells = <0>;
		};
	};

	tcphy1: phy@ff800000 {
		compatible = "rockchip,rk3399-typec-phy";
		reg = <0x0 0xff800000 0x0 0x40000>;
		rockchip,grf = <&grf>;
		extcon = <&fusb1>;
		clocks = <&cru SCLK_UPHY1_TCPDCORE>,
			 <&cru SCLK_UPHY1_TCPDPHY_REF>;
		clock-names = "tcpdcore", "tcpdphy-ref";
		assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
		assigned-clock-rates = <50000000>;
		resets = <&cru SRST_UPHY1>,
			 <&cru SRST_UPHY1_PIPE_L00>,
			 <&cru SRST_P_UPHY1_TCPHY>;
		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
		rockchip,typec-conn-dir = <0xe58c 0 16>;
		rockchip,usb3tousb2-en = <0xe58c 3 19>;
		rockchip,external-psm = <0xe594 14 30>;
		rockchip,pipe-status = <0xe5c0 16 16>;

		tcphy1_dp: dp-port {
			#phy-cells = <0>;
		};

		tcphy1_usb3: usb3-port {
			#phy-cells = <0>;
		};
	};