| Allwinner sun4i USB PHY |
| ----------------------- |
| |
| Required properties: |
| - compatible : should be one of |
| * allwinner,sun4i-a10-usb-phy |
| * allwinner,sun5i-a13-usb-phy |
| * allwinner,sun6i-a31-usb-phy |
| * allwinner,sun7i-a20-usb-phy |
| * allwinner,sun8i-a23-usb-phy |
| * allwinner,sun8i-a33-usb-phy |
| * allwinner,sun8i-h3-usb-phy |
| * allwinner,sun8i-v3s-usb-phy |
| * allwinner,sun50i-a64-usb-phy |
| - reg : a list of offset + length pairs |
| - reg-names : |
| * "phy_ctrl" |
| * "pmu0" for H3, V3s and A64 |
| * "pmu1" |
| * "pmu2" for sun4i, sun6i or sun7i |
| - #phy-cells : from the generic phy bindings, must be 1 |
| - clocks : phandle + clock specifier for the phy clocks |
| - clock-names : |
| * "usb_phy" for sun4i, sun5i or sun7i |
| * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i |
| * "usb0_phy", "usb1_phy" for sun8i |
| - resets : a list of phandle + reset specifier pairs |
| - reset-names : |
| * "usb0_reset" |
| * "usb1_reset" |
| * "usb2_reset" for sun4i, sun6i or sun7i |
| |
| Optional properties: |
| - usb0_id_det-gpios : gpio phandle for reading the otg id pin value |
| - usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus |
| - usb0_vbus_power-supply: power-supply phandle for usb0 vbus presence detect |
| - usb0_vbus-supply : regulator phandle for controller usb0 vbus |
| - usb1_vbus-supply : regulator phandle for controller usb1 vbus |
| - usb2_vbus-supply : regulator phandle for controller usb2 vbus |
| |
| Example: |
| usbphy: phy@0x01c13400 { |
| #phy-cells = <1>; |
| compatible = "allwinner,sun4i-a10-usb-phy"; |
| /* phy base regs, phy1 pmu reg, phy2 pmu reg */ |
| reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>; |
| reg-names = "phy_ctrl", "pmu1", "pmu2"; |
| clocks = <&usb_clk 8>; |
| clock-names = "usb_phy"; |
| resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>; |
| reset-names = "usb0_reset", "usb1_reset", "usb2_reset"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; |
| usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */ |
| usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ |
| usb0_vbus-supply = <®_usb0_vbus>; |
| usb1_vbus-supply = <®_usb1_vbus>; |
| usb2_vbus-supply = <®_usb2_vbus>; |
| }; |