# SPDX-License-Identifier: GPL-2.0
config BF52x
	def_bool y
	depends on (BF522 || BF523 || BF524 || BF525 || BF526 || BF527)

if (BF52x)

source "arch/blackfin/mach-bf527/boards/Kconfig"

menu "BF527 Specific Configuration"

comment "Alternative Multiplexing Scheme"

choice
	prompt "SPORT0"
	default BF527_SPORT0_PORTG
	help
	  Select PORT used for SPORT0. See Hardware Reference Manual

config BF527_SPORT0_PORTF
	bool "PORT F"
	help
	  PORT F

config BF527_SPORT0_PORTG
	bool "PORT G"
	help
	  PORT G
endchoice

choice
	prompt "SPORT0 TSCLK Location"
	depends on BF527_SPORT0_PORTG
	default BF527_SPORT0_TSCLK_PG10
	help
	  Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual

config BF527_SPORT0_TSCLK_PG10
	bool "PORT PG10"
	help
	  PORT PG10

config BF527_SPORT0_TSCLK_PG14
	bool "PORT PG14"
	help
	  PORT PG14
endchoice

choice
	prompt "UART1"
	default BF527_UART1_PORTF
	help
	  Select PORT used for UART1. See Hardware Reference Manual

config BF527_UART1_PORTF
	bool "PORT F"
	help
	  PORT F

config BF527_UART1_PORTG
	bool "PORT G"
	help
	  PORT G
endchoice

choice
	prompt "NAND (NFC) Data"
	default BF527_NAND_D_PORTH
	help
	  Select PORT used for NAND Data Bus. See Hardware Reference Manual

config BF527_NAND_D_PORTF
	bool "PORT F"
	help
	  PORT F

config BF527_NAND_D_PORTH
	bool "PORT H"
	help
	  PORT H
endchoice

comment "Hysteresis/Schmitt Trigger Control"
config BFIN_HYSTERESIS_CONTROL
	bool "Enable Hysteresis Control"
	help
	  The ADSP-BF52x allows to control input hysteresis for Port F,
	  Port G and Port H and other processor signal inputs.
	  The Schmitt trigger enables can be set only for pin groups.
	  Saying Y will overwrite the default reset or boot loader
	  initialization.

menu "PORT F"
	depends on BFIN_HYSTERESIS_CONTROL
config GPIO_HYST_PORTF_0_7
	bool "Enable Hysteresis on PORTF {0...7}"
config GPIO_HYST_PORTF_8_9
	bool "Enable Hysteresis on PORTF {8, 9}"
config GPIO_HYST_PORTF_10
	bool "Enable Hysteresis on PORTF 10"
config GPIO_HYST_PORTF_11
	bool "Enable Hysteresis on PORTF 11"
config GPIO_HYST_PORTF_12_13
	bool "Enable Hysteresis on PORTF {12, 13}"
config GPIO_HYST_PORTF_14_15
	bool "Enable Hysteresis on PORTF {14, 15}"
endmenu

menu "PORT G"
	depends on BFIN_HYSTERESIS_CONTROL
config GPIO_HYST_PORTG_0
	bool "Enable Hysteresis on PORTG 0"
config GPIO_HYST_PORTG_1_4
	bool "Enable Hysteresis on PORTG {1...4}"
config GPIO_HYST_PORTG_5_6
	bool "Enable Hysteresis on PORTG {5, 6}"
config GPIO_HYST_PORTG_7_8
	bool "Enable Hysteresis on PORTG {7, 8}"
config GPIO_HYST_PORTG_9
	bool "Enable Hysteresis on PORTG 9"
config GPIO_HYST_PORTG_10
	bool "Enable Hysteresis on PORTG 10"
config GPIO_HYST_PORTG_11_13
	bool "Enable Hysteresis on PORTG {11...13}"
config GPIO_HYST_PORTG_14_15
	bool "Enable Hysteresis on PORTG {14, 15}"
endmenu

menu "PORT H"
	depends on BFIN_HYSTERESIS_CONTROL
config GPIO_HYST_PORTH_0_7
	bool "Enable Hysteresis on PORTH {0...7}"
config GPIO_HYST_PORTH_8
	bool "Enable Hysteresis on PORTH 8"
config GPIO_HYST_PORTH_9_15
	bool "Enable Hysteresis on PORTH {9...15}"
endmenu

menu "None-GPIO"
	depends on BFIN_HYSTERESIS_CONTROL
config NONEGPIO_HYST_TMR0_FS1_PPICLK
	bool "Enable Hysteresis on {TMR0, PPI_FS1, PPI_CLK}"
config NONEGPIO_HYST_NMI_RST_BMODE
	bool "Enable Hysteresis on {NMI, RESET, BMODE}"
config NONEGPIO_HYST_JTAG
	bool "Enable Hysteresis on JTAG"
endmenu

comment "Interrupt Priority Assignment"
menu "Priority"

config IRQ_PLL_WAKEUP
	int "IRQ_PLL_WAKEUP"
	default 7
config IRQ_DMA0_ERROR
	int "IRQ_DMA0_ERROR"
	default 7
config IRQ_DMAR0_BLK
	int "IRQ_DMAR0_BLK"
	default 7
config IRQ_DMAR1_BLK
	int "IRQ_DMAR1_BLK"
	default 7
config IRQ_DMAR0_OVR
	int "IRQ_DMAR0_OVR"
	default 7
config IRQ_DMAR1_OVR
	int "IRQ_DMAR1_OVR"
	default 7
config IRQ_PPI_ERROR
	int "IRQ_PPI_ERROR"
	default 7
config IRQ_MAC_ERROR
	int "IRQ_MAC_ERROR"
	default 7
config IRQ_SPORT0_ERROR
	int "IRQ_SPORT0_ERROR"
	default 7
config IRQ_SPORT1_ERROR
	int "IRQ_SPORT1_ERROR"
	default 7
config IRQ_UART0_ERROR
	int "IRQ_UART0_ERROR"
	default 7
config IRQ_UART1_ERROR
	int "IRQ_UART1_ERROR"
	default 7
config IRQ_RTC
	int "IRQ_RTC"
	default 8
config IRQ_PPI
	int "IRQ_PPI"
	default 8
config IRQ_SPORT0_RX
	int "IRQ_SPORT0_RX"
	default 9
config IRQ_SPORT0_TX
	int "IRQ_SPORT0_TX"
	default 9
config IRQ_SPORT1_RX
	int "IRQ_SPORT1_RX"
	default 9
config IRQ_SPORT1_TX
	int "IRQ_SPORT1_TX"
	default 9
config IRQ_TWI
	int "IRQ_TWI"
	default 10
config IRQ_SPI
	int "IRQ_SPI"
	default 10
config IRQ_UART0_RX
	int "IRQ_UART0_RX"
	default 10
config IRQ_UART0_TX
	int "IRQ_UART0_TX"
	default 10
config IRQ_UART1_RX
	int "IRQ_UART1_RX"
	default 10
config IRQ_UART1_TX
	int "IRQ_UART1_TX"
	default 10
config IRQ_OPTSEC
	int "IRQ_OPTSEC"
	default 11
config IRQ_CNT
	int "IRQ_CNT"
	default 11
config IRQ_MAC_RX
	int "IRQ_MAC_RX"
	default 11
config IRQ_PORTH_INTA
	int "IRQ_PORTH_INTA"
	default 11
config IRQ_MAC_TX
	int "IRQ_MAC_TX/NFC"
	default 11
config IRQ_PORTH_INTB
	int "IRQ_PORTH_INTB"
	default 11
config IRQ_TIMER0
	int "IRQ_TIMER0"
	default 7 if TICKSOURCE_GPTMR0
	default 8
config IRQ_TIMER1
	int "IRQ_TIMER1"
	default 12
config IRQ_TIMER2
	int "IRQ_TIMER2"
	default 12
config IRQ_TIMER3
	int "IRQ_TIMER3"
	default 12
config IRQ_TIMER4
	int "IRQ_TIMER4"
	default 12
config IRQ_TIMER5
	int "IRQ_TIMER5"
	default 12
config IRQ_TIMER6
	int "IRQ_TIMER6"
	default 12
config IRQ_TIMER7
	int "IRQ_TIMER7"
	default 12
config IRQ_PORTG_INTA
	int "IRQ_PORTG_INTA"
	default 12
config IRQ_PORTG_INTB
	int "IRQ_PORTG_INTB"
	default 12
config IRQ_MEM_DMA0
	int "IRQ_MEM_DMA0"
	default 13
config IRQ_MEM_DMA1
	int "IRQ_MEM_DMA1"
	default 13
config IRQ_WATCH
	int "IRQ_WATCH"
	default 13
config IRQ_PORTF_INTA
	int "IRQ_PORTF_INTA"
	default 13
config IRQ_PORTF_INTB
	int "IRQ_PORTF_INTB"
	default 13
config IRQ_SPI_ERROR
	int "IRQ_SPI_ERROR"
	default 7
config IRQ_NFC_ERROR
	int "IRQ_NFC_ERROR"
	default 7
config IRQ_HDMA_ERROR
	int "IRQ_HDMA_ERROR"
	default 7
config IRQ_HDMA
	int "IRQ_HDMA"
	default 7
config IRQ_USB_EINT
	int "IRQ_USB_EINT"
	default 10
config IRQ_USB_INT0
	int "IRQ_USB_INT0"
	default 10
config IRQ_USB_INT1
	int "IRQ_USB_INT1"
	default 10
config IRQ_USB_INT2
	int "IRQ_USB_INT2"
	default 10
config IRQ_USB_DMA
	int "IRQ_USB_DMA"
	default 10

	help
	  Enter the priority numbers between 7-13 ONLY.  Others are Reserved.
	  This applies to all the above.  It is not recommended to assign the
	  highest priority number 7 to UART or any other device.

endmenu

endmenu

endif