AT91 MMC update for 2.6.19
The driver is usable on the newer SAM9 processors so replace all text
references to AT91RM9200 with just AT91.
The controller bug where all the words are byte-swapped is fixed on the
AT91SAM9 processors. The byte-swapping work-around therefore only needs
to be done if cpu_is_at91rm9200().
[Original patch from Wojtek Kaniewski]
The AT91RM9200 and AT91SAM9260 processors support two MMC/SD slots - the
slot which is connected is now passed via the platform_data and the
correct slot selected in the AT91_MCI_SDCR register.
The driver should not be calling at91_set_gpio_output() since the VCC
pin should have already been configured as an output in the
processor/board setup code. The driver should call
at91_set_gpio_value().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
diff --git a/drivers/mmc/at91_mci.c b/drivers/mmc/at91_mci.c
index d500b6b..08a33c3 100644
--- a/drivers/mmc/at91_mci.c
+++ b/drivers/mmc/at91_mci.c
@@ -1,5 +1,5 @@
/*
- * linux/drivers/mmc/at91_mci.c - ATMEL AT91RM9200 MCI Driver
+ * linux/drivers/mmc/at91_mci.c - ATMEL AT91 MCI Driver
*
* Copyright (C) 2005 Cougar Creek Computing Devices Ltd, All Rights Reserved
*
@@ -11,7 +11,7 @@
*/
/*
- This is the AT91RM9200 MCI driver that has been tested with both MMC cards
+ This is the AT91 MCI driver that has been tested with both MMC cards
and SD-cards. Boards that support write protect are now supported.
The CCAT91SBC001 board does not support SD cards.
@@ -38,8 +38,8 @@
controller to manage the transfers.
A read is done from the controller directly to the scatterlist passed in from the request.
- Due to a bug in the controller, when a read is completed, all the words are byte
- swapped in the scatterlist buffers.
+ Due to a bug in the AT91RM9200 controller, when a read is completed, all the words are byte
+ swapped in the scatterlist buffers. AT91SAM926x are not affected by this bug.
The sequence of read interrupts is: ENDRX, RXBUFF, CMDRDY
@@ -72,6 +72,7 @@
#include <asm/irq.h>
#include <asm/mach/mmc.h>
#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91_mci.h>
#include <asm/arch/at91_pdc.h>
@@ -147,7 +148,6 @@
for (i = 0; i < len; i++) {
struct scatterlist *sg;
int amount;
- int index;
unsigned int *sgbuffer;
sg = &data->sg[i];
@@ -155,10 +155,15 @@
sgbuffer = kmap_atomic(sg->page, KM_BIO_SRC_IRQ) + sg->offset;
amount = min(size, sg->length);
size -= amount;
- amount /= 4;
- for (index = 0; index < amount; index++)
- *dmabuf++ = swab32(sgbuffer[index]);
+ if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */
+ int index;
+
+ for (index = 0; index < (amount / 4); index++)
+ *dmabuf++ = swab32(sgbuffer[index]);
+ }
+ else
+ memcpy(dmabuf, sgbuffer, amount);
kunmap_atomic(sgbuffer, KM_BIO_SRC_IRQ);
@@ -265,8 +270,6 @@
while (host->in_use_index < host->transfer_index) {
unsigned int *buffer;
- int index;
- int len;
struct scatterlist *sg;
@@ -284,11 +287,13 @@
data->bytes_xfered += sg->length;
- len = sg->length / 4;
+ if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */
+ int index;
- for (index = 0; index < len; index++) {
- buffer[index] = swab32(buffer[index]);
+ for (index = 0; index < (sg->length / 4); index++)
+ buffer[index] = swab32(buffer[index]);
}
+
kunmap_atomic(buffer, KM_BIO_SRC_IRQ);
flush_dcache_page(sg->page);
}
@@ -339,7 +344,9 @@
at91_mci_write(host, AT91_MCI_IDR, 0xffffffff);
at91_mci_write(host, AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC);
at91_mci_write(host, AT91_MCI_MR, AT91_MCI_PDCMODE | 0x34a);
- at91_mci_write(host, AT91_MCI_SDCR, 0);
+
+ /* use Slot A or B (only one at same time) */
+ at91_mci_write(host, AT91_MCI_SDCR, host->board->slot_b);
}
/*
@@ -637,11 +644,11 @@
if (host->board->vcc_pin) {
switch (ios->power_mode) {
case MMC_POWER_OFF:
- at91_set_gpio_output(host->board->vcc_pin, 0);
+ at91_set_gpio_value(host->board->vcc_pin, 0);
break;
case MMC_POWER_UP:
case MMC_POWER_ON:
- at91_set_gpio_output(host->board->vcc_pin, 1);
+ at91_set_gpio_value(host->board->vcc_pin, 1);
break;
}
}
@@ -754,7 +761,7 @@
present ? "insert" : "remove");
if (!present) {
pr_debug("****** Resetting SD-card bus width ******\n");
- at91_mci_write(host, AT91_MCI_SDCR, 0);
+ at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS);
}
mmc_detect_change(host->mmc, msecs_to_jiffies(100));
}
