| // SPDX-License-Identifier: GPL-2.0 | |
| #include "r8192U.h" | |
| #include "r8192U_hw.h" | |
| #include "r819xU_phy.h" | |
| #include "r819xU_phyreg.h" | |
| #include "r8190_rtl8256.h" | |
| #include "r8192U_dm.h" | |
| #include "r819xU_firmware_img.h" | |
| #include "dot11d.h" | |
| #include <linux/bitops.h> | |
| static u32 RF_CHANNEL_TABLE_ZEBRA[] = { | |
| 0, | |
| 0x085c, /* 2412 1 */ | |
| 0x08dc, /* 2417 2 */ | |
| 0x095c, /* 2422 3 */ | |
| 0x09dc, /* 2427 4 */ | |
| 0x0a5c, /* 2432 5 */ | |
| 0x0adc, /* 2437 6 */ | |
| 0x0b5c, /* 2442 7 */ | |
| 0x0bdc, /* 2447 8 */ | |
| 0x0c5c, /* 2452 9 */ | |
| 0x0cdc, /* 2457 10 */ | |
| 0x0d5c, /* 2462 11 */ | |
| 0x0ddc, /* 2467 12 */ | |
| 0x0e5c, /* 2472 13 */ | |
| 0x0f72, /* 2484 */ | |
| }; | |
| #define rtl819XPHY_REG_1T2RArray Rtl8192UsbPHY_REG_1T2RArray | |
| #define rtl819XMACPHY_Array_PG Rtl8192UsbMACPHY_Array_PG | |
| #define rtl819XMACPHY_Array Rtl8192UsbMACPHY_Array | |
| #define rtl819XRadioA_Array Rtl8192UsbRadioA_Array | |
| #define rtl819XRadioB_Array Rtl8192UsbRadioB_Array | |
| #define rtl819XRadioC_Array Rtl8192UsbRadioC_Array | |
| #define rtl819XRadioD_Array Rtl8192UsbRadioD_Array | |
| #define rtl819XAGCTAB_Array Rtl8192UsbAGCTAB_Array | |
| /****************************************************************************** | |
| * function: This function checks different RF type to execute legal judgement. | |
| * If RF Path is illegal, we will return false. | |
| * input: net_device *dev | |
| * u32 eRFPath | |
| * output: none | |
| * return: 0(illegal, false), 1(legal, true) | |
| *****************************************************************************/ | |
| u8 rtl8192_phy_CheckIsLegalRFPath(struct net_device *dev, u32 eRFPath) | |
| { | |
| u8 ret = 1; | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| if (priv->rf_type == RF_2T4R) { | |
| ret = 0; | |
| } else if (priv->rf_type == RF_1T2R) { | |
| if (eRFPath == RF90_PATH_A || eRFPath == RF90_PATH_B) | |
| ret = 1; | |
| else if (eRFPath == RF90_PATH_C || eRFPath == RF90_PATH_D) | |
| ret = 0; | |
| } | |
| return ret; | |
| } | |
| /****************************************************************************** | |
| * function: This function sets specific bits to BB register | |
| * input: net_device *dev | |
| * u32 reg_addr //target addr to be modified | |
| * u32 bitmask //taget bit pos to be modified | |
| * u32 data //value to be write | |
| * output: none | |
| * return: none | |
| * notice: | |
| ******************************************************************************/ | |
| void rtl8192_setBBreg(struct net_device *dev, u32 reg_addr, u32 bitmask, | |
| u32 data) | |
| { | |
| u32 reg, bitshift; | |
| if (bitmask != bMaskDWord) { | |
| read_nic_dword(dev, reg_addr, ®); | |
| bitshift = ffs(bitmask) - 1; | |
| reg &= ~bitmask; | |
| reg |= data << bitshift; | |
| write_nic_dword(dev, reg_addr, reg); | |
| } else { | |
| write_nic_dword(dev, reg_addr, data); | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function reads specific bits from BB register | |
| * input: net_device *dev | |
| * u32 reg_addr //target addr to be readback | |
| * u32 bitmask //taget bit pos to be readback | |
| * output: none | |
| * return: u32 data //the readback register value | |
| * notice: | |
| ******************************************************************************/ | |
| u32 rtl8192_QueryBBReg(struct net_device *dev, u32 reg_addr, u32 bitmask) | |
| { | |
| u32 reg, bitshift; | |
| read_nic_dword(dev, reg_addr, ®); | |
| bitshift = ffs(bitmask) - 1; | |
| return (reg & bitmask) >> bitshift; | |
| } | |
| static u32 phy_FwRFSerialRead(struct net_device *dev, RF90_RADIO_PATH_E eRFPath, | |
| u32 offset); | |
| static void phy_FwRFSerialWrite(struct net_device *dev, | |
| RF90_RADIO_PATH_E eRFPath, u32 offset, | |
| u32 data); | |
| /****************************************************************************** | |
| * function: This function reads register from RF chip | |
| * input: net_device *dev | |
| * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D | |
| * u32 offset //target address to be read | |
| * output: none | |
| * return: u32 readback value | |
| * notice: There are three types of serial operations: | |
| * (1) Software serial write. | |
| * (2)Hardware LSSI-Low Speed Serial Interface. | |
| * (3)Hardware HSSI-High speed serial write. | |
| * Driver here need to implement (1) and (2) | |
| * ---need more spec for this information. | |
| ******************************************************************************/ | |
| static u32 rtl8192_phy_RFSerialRead(struct net_device *dev, | |
| RF90_RADIO_PATH_E eRFPath, u32 offset) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u32 ret = 0; | |
| u32 new_offset = 0; | |
| BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath]; | |
| rtl8192_setBBreg(dev, pPhyReg->rfLSSIReadBack, bLSSIReadBackData, 0); | |
| /* Make sure RF register offset is correct */ | |
| offset &= 0x3f; | |
| /* Switch page for 8256 RF IC */ | |
| if (priv->rf_chip == RF_8256) { | |
| if (offset >= 31) { | |
| priv->RfReg0Value[eRFPath] |= 0x140; | |
| /* Switch to Reg_Mode2 for Reg 31-45 */ | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, | |
| bMaskDWord, | |
| priv->RfReg0Value[eRFPath]<<16); | |
| /* Modify offset */ | |
| new_offset = offset - 30; | |
| } else if (offset >= 16) { | |
| priv->RfReg0Value[eRFPath] |= 0x100; | |
| priv->RfReg0Value[eRFPath] &= (~0x40); | |
| /* Switch to Reg_Mode1 for Reg16-30 */ | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, | |
| bMaskDWord, | |
| priv->RfReg0Value[eRFPath]<<16); | |
| new_offset = offset - 15; | |
| } else { | |
| new_offset = offset; | |
| } | |
| } else { | |
| RT_TRACE((COMP_PHY|COMP_ERR), | |
| "check RF type here, need to be 8256\n"); | |
| new_offset = offset; | |
| } | |
| /* Put desired read addr to LSSI control Register */ | |
| rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadAddress, | |
| new_offset); | |
| /* Issue a posedge trigger */ | |
| rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x0); | |
| rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x1); | |
| /* TODO: we should not delay such a long time. Ask for help from SD3 */ | |
| usleep_range(1000, 1000); | |
| ret = rtl8192_QueryBBReg(dev, pPhyReg->rfLSSIReadBack, | |
| bLSSIReadBackData); | |
| /* Switch back to Reg_Mode0 */ | |
| if (priv->rf_chip == RF_8256) { | |
| priv->RfReg0Value[eRFPath] &= 0xebf; | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, | |
| priv->RfReg0Value[eRFPath] << 16); | |
| } | |
| return ret; | |
| } | |
| /****************************************************************************** | |
| * function: This function writes data to RF register | |
| * input: net_device *dev | |
| * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D | |
| * u32 offset //target address to be written | |
| * u32 data //the new register data to be written | |
| * output: none | |
| * return: none | |
| * notice: For RF8256 only. | |
| * =========================================================================== | |
| * Reg Mode RegCTL[1] RegCTL[0] Note | |
| * (Reg00[12]) (Reg00[10]) | |
| * =========================================================================== | |
| * Reg_Mode0 0 x Reg 0 ~ 15(0x0 ~ 0xf) | |
| * --------------------------------------------------------------------------- | |
| * Reg_Mode1 1 0 Reg 16 ~ 30(0x1 ~ 0xf) | |
| * --------------------------------------------------------------------------- | |
| * Reg_Mode2 1 1 Reg 31 ~ 45(0x1 ~ 0xf) | |
| * --------------------------------------------------------------------------- | |
| *****************************************************************************/ | |
| static void rtl8192_phy_RFSerialWrite(struct net_device *dev, | |
| RF90_RADIO_PATH_E eRFPath, u32 offset, | |
| u32 data) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u32 DataAndAddr = 0, new_offset = 0; | |
| BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath]; | |
| offset &= 0x3f; | |
| if (priv->rf_chip == RF_8256) { | |
| if (offset >= 31) { | |
| priv->RfReg0Value[eRFPath] |= 0x140; | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, | |
| bMaskDWord, | |
| priv->RfReg0Value[eRFPath] << 16); | |
| new_offset = offset - 30; | |
| } else if (offset >= 16) { | |
| priv->RfReg0Value[eRFPath] |= 0x100; | |
| priv->RfReg0Value[eRFPath] &= (~0x40); | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, | |
| bMaskDWord, | |
| priv->RfReg0Value[eRFPath]<<16); | |
| new_offset = offset - 15; | |
| } else { | |
| new_offset = offset; | |
| } | |
| } else { | |
| RT_TRACE((COMP_PHY|COMP_ERR), | |
| "check RF type here, need to be 8256\n"); | |
| new_offset = offset; | |
| } | |
| /* Put write addr in [5:0] and write data in [31:16] */ | |
| DataAndAddr = (data<<16) | (new_offset&0x3f); | |
| /* Write operation */ | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, DataAndAddr); | |
| if (offset == 0x0) | |
| priv->RfReg0Value[eRFPath] = data; | |
| /* Switch back to Reg_Mode0 */ | |
| if (priv->rf_chip == RF_8256) { | |
| if (offset != 0) { | |
| priv->RfReg0Value[eRFPath] &= 0xebf; | |
| rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, | |
| bMaskDWord, | |
| priv->RfReg0Value[eRFPath] << 16); | |
| } | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function set specific bits to RF register | |
| * input: net_device dev | |
| * RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D | |
| * u32 reg_addr //target addr to be modified | |
| * u32 bitmask //taget bit pos to be modified | |
| * u32 data //value to be written | |
| * output: none | |
| * return: none | |
| * notice: | |
| *****************************************************************************/ | |
| void rtl8192_phy_SetRFReg(struct net_device *dev, RF90_RADIO_PATH_E eRFPath, | |
| u32 reg_addr, u32 bitmask, u32 data) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u32 reg, bitshift; | |
| if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath)) | |
| return; | |
| if (priv->Rf_Mode == RF_OP_By_FW) { | |
| if (bitmask != bMask12Bits) { | |
| /* RF data is 12 bits only */ | |
| reg = phy_FwRFSerialRead(dev, eRFPath, reg_addr); | |
| bitshift = ffs(bitmask) - 1; | |
| reg &= ~bitmask; | |
| reg |= data << bitshift; | |
| phy_FwRFSerialWrite(dev, eRFPath, reg_addr, reg); | |
| } else { | |
| phy_FwRFSerialWrite(dev, eRFPath, reg_addr, data); | |
| } | |
| udelay(200); | |
| } else { | |
| if (bitmask != bMask12Bits) { | |
| /* RF data is 12 bits only */ | |
| reg = rtl8192_phy_RFSerialRead(dev, eRFPath, reg_addr); | |
| bitshift = ffs(bitmask) - 1; | |
| reg &= ~bitmask; | |
| reg |= data << bitshift; | |
| rtl8192_phy_RFSerialWrite(dev, eRFPath, reg_addr, reg); | |
| } else { | |
| rtl8192_phy_RFSerialWrite(dev, eRFPath, reg_addr, data); | |
| } | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function reads specific bits from RF register | |
| * input: net_device *dev | |
| * u32 reg_addr //target addr to be readback | |
| * u32 bitmask //taget bit pos to be readback | |
| * output: none | |
| * return: u32 data //the readback register value | |
| * notice: | |
| *****************************************************************************/ | |
| u32 rtl8192_phy_QueryRFReg(struct net_device *dev, RF90_RADIO_PATH_E eRFPath, | |
| u32 reg_addr, u32 bitmask) | |
| { | |
| u32 reg, bitshift; | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath)) | |
| return 0; | |
| if (priv->Rf_Mode == RF_OP_By_FW) { | |
| reg = phy_FwRFSerialRead(dev, eRFPath, reg_addr); | |
| udelay(200); | |
| } else { | |
| reg = rtl8192_phy_RFSerialRead(dev, eRFPath, reg_addr); | |
| } | |
| bitshift = ffs(bitmask) - 1; | |
| reg = (reg & bitmask) >> bitshift; | |
| return reg; | |
| } | |
| /****************************************************************************** | |
| * function: We support firmware to execute RF-R/W. | |
| * input: net_device *dev | |
| * RF90_RADIO_PATH_E eRFPath | |
| * u32 offset | |
| * output: none | |
| * return: u32 | |
| * notice: | |
| ****************************************************************************/ | |
| static u32 phy_FwRFSerialRead(struct net_device *dev, RF90_RADIO_PATH_E eRFPath, | |
| u32 offset) | |
| { | |
| u32 reg = 0; | |
| u32 data = 0; | |
| u8 time = 0; | |
| u32 tmp; | |
| /* Firmware RF Write control. | |
| * We can not execute the scheme in the initial step. | |
| * Otherwise, RF-R/W will waste much time. | |
| * This is only for site survey. | |
| */ | |
| /* 1. Read operation need not insert data. bit 0-11 */ | |
| /* 2. Write RF register address. bit 12-19 */ | |
| data |= ((offset&0xFF)<<12); | |
| /* 3. Write RF path. bit 20-21 */ | |
| data |= ((eRFPath&0x3)<<20); | |
| /* 4. Set RF read indicator. bit 22=0 */ | |
| /* 5. Trigger Fw to operate the command. bit 31 */ | |
| data |= 0x80000000; | |
| /* 6. We can not execute read operation if bit 31 is 1. */ | |
| read_nic_dword(dev, QPNR, &tmp); | |
| while (tmp & 0x80000000) { | |
| /* If FW can not finish RF-R/W for more than ?? times. | |
| * We must reset FW. | |
| */ | |
| if (time++ < 100) { | |
| udelay(10); | |
| read_nic_dword(dev, QPNR, &tmp); | |
| } else { | |
| break; | |
| } | |
| } | |
| /* 7. Execute read operation. */ | |
| write_nic_dword(dev, QPNR, data); | |
| /* 8. Check if firmware send back RF content. */ | |
| read_nic_dword(dev, QPNR, &tmp); | |
| while (tmp & 0x80000000) { | |
| /* If FW can not finish RF-R/W for more than ?? times. | |
| * We must reset FW. | |
| */ | |
| if (time++ < 100) { | |
| udelay(10); | |
| read_nic_dword(dev, QPNR, &tmp); | |
| } else { | |
| return 0; | |
| } | |
| } | |
| read_nic_dword(dev, RF_DATA, ®); | |
| return reg; | |
| } | |
| /****************************************************************************** | |
| * function: We support firmware to execute RF-R/W. | |
| * input: net_device *dev | |
| * RF90_RADIO_PATH_E eRFPath | |
| * u32 offset | |
| * u32 data | |
| * output: none | |
| * return: none | |
| * notice: | |
| ****************************************************************************/ | |
| static void phy_FwRFSerialWrite(struct net_device *dev, | |
| RF90_RADIO_PATH_E eRFPath, u32 offset, u32 data) | |
| { | |
| u8 time = 0; | |
| u32 tmp; | |
| /* Firmware RF Write control. | |
| * We can not execute the scheme in the initial step. | |
| * Otherwise, RF-R/W will waste much time. | |
| * This is only for site survey. | |
| */ | |
| /* 1. Set driver write bit and 12 bit data. bit 0-11 */ | |
| /* 2. Write RF register address. bit 12-19 */ | |
| data |= ((offset&0xFF)<<12); | |
| /* 3. Write RF path. bit 20-21 */ | |
| data |= ((eRFPath&0x3)<<20); | |
| /* 4. Set RF write indicator. bit 22=1 */ | |
| data |= 0x400000; | |
| /* 5. Trigger Fw to operate the command. bit 31=1 */ | |
| data |= 0x80000000; | |
| /* 6. Write operation. We can not write if bit 31 is 1. */ | |
| read_nic_dword(dev, QPNR, &tmp); | |
| while (tmp & 0x80000000) { | |
| /* If FW can not finish RF-R/W for more than ?? times. | |
| * We must reset FW. | |
| */ | |
| if (time++ < 100) { | |
| udelay(10); | |
| read_nic_dword(dev, QPNR, &tmp); | |
| } else { | |
| break; | |
| } | |
| } | |
| /* 7. No matter check bit. We always force the write. | |
| * Because FW will not accept the command. | |
| */ | |
| write_nic_dword(dev, QPNR, data); | |
| /* According to test, we must delay 20us to wait firmware | |
| * to finish RF write operation. | |
| */ | |
| /* We support delay in firmware side now. */ | |
| } | |
| /****************************************************************************** | |
| * function: This function reads BB parameters from header file we generate, | |
| * and do register read/write | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| * notice: BB parameters may change all the time, so please make | |
| * sure it has been synced with the newest. | |
| *****************************************************************************/ | |
| void rtl8192_phy_configmac(struct net_device *dev) | |
| { | |
| u32 dwArrayLen = 0, i; | |
| u32 *pdwArray = NULL; | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| if (priv->btxpowerdata_readfromEEPORM) { | |
| RT_TRACE(COMP_PHY, "Rtl819XMACPHY_Array_PG\n"); | |
| dwArrayLen = MACPHY_Array_PGLength; | |
| pdwArray = rtl819XMACPHY_Array_PG; | |
| } else { | |
| RT_TRACE(COMP_PHY, "Rtl819XMACPHY_Array\n"); | |
| dwArrayLen = MACPHY_ArrayLength; | |
| pdwArray = rtl819XMACPHY_Array; | |
| } | |
| for (i = 0; i < dwArrayLen; i = i+3) { | |
| if (pdwArray[i] == 0x318) | |
| pdwArray[i+2] = 0x00000800; | |
| RT_TRACE(COMP_DBG, | |
| "Rtl8190MACPHY_Array[0]=%x Rtl8190MACPHY_Array[1]=%x Rtl8190MACPHY_Array[2]=%x\n", | |
| pdwArray[i], pdwArray[i+1], pdwArray[i+2]); | |
| rtl8192_setBBreg(dev, pdwArray[i], pdwArray[i+1], | |
| pdwArray[i+2]); | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function does dirty work | |
| * input: net_device *dev | |
| * u8 ConfigType | |
| * output: none | |
| * return: none | |
| * notice: BB parameters may change all the time, so please make | |
| * sure it has been synced with the newest. | |
| *****************************************************************************/ | |
| void rtl8192_phyConfigBB(struct net_device *dev, u8 ConfigType) | |
| { | |
| u32 i; | |
| #ifdef TO_DO_LIST | |
| u32 *rtl8192PhyRegArrayTable = NULL, *rtl8192AgcTabArrayTable = NULL; | |
| if (Adapter->bInHctTest) { | |
| PHY_REGArrayLen = PHY_REGArrayLengthDTM; | |
| AGCTAB_ArrayLen = AGCTAB_ArrayLengthDTM; | |
| Rtl8190PHY_REGArray_Table = Rtl819XPHY_REGArrayDTM; | |
| Rtl8190AGCTAB_Array_Table = Rtl819XAGCTAB_ArrayDTM; | |
| } | |
| #endif | |
| if (ConfigType == BaseBand_Config_PHY_REG) { | |
| for (i = 0; i < PHY_REG_1T2RArrayLength; i += 2) { | |
| rtl8192_setBBreg(dev, rtl819XPHY_REG_1T2RArray[i], | |
| bMaskDWord, | |
| rtl819XPHY_REG_1T2RArray[i+1]); | |
| RT_TRACE(COMP_DBG, | |
| "i: %x, Rtl819xUsbPHY_REGArray[0]=%x Rtl819xUsbPHY_REGArray[1]=%x\n", | |
| i, rtl819XPHY_REG_1T2RArray[i], | |
| rtl819XPHY_REG_1T2RArray[i+1]); | |
| } | |
| } else if (ConfigType == BaseBand_Config_AGC_TAB) { | |
| for (i = 0; i < AGCTAB_ArrayLength; i += 2) { | |
| rtl8192_setBBreg(dev, rtl819XAGCTAB_Array[i], | |
| bMaskDWord, rtl819XAGCTAB_Array[i+1]); | |
| RT_TRACE(COMP_DBG, | |
| "i: %x, rtl819XAGCTAB_Array[0]=%x rtl819XAGCTAB_Array[1]=%x\n", | |
| i, rtl819XAGCTAB_Array[i], | |
| rtl819XAGCTAB_Array[i+1]); | |
| } | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function initializes Register definition offset for | |
| * Radio Path A/B/C/D | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| * notice: Initialization value here is constant and it should never | |
| * be changed | |
| *****************************************************************************/ | |
| static void rtl8192_InitBBRFRegDef(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| /* RF Interface Software Control */ | |
| /* 16 LSBs if read 32-bit from 0x870 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfintfs = rFPGA0_XAB_RFInterfaceSW; | |
| /* 16 MSBs if read 32-bit from 0x870 (16-bit for 0x872) */ | |
| priv->PHYRegDef[RF90_PATH_B].rfintfs = rFPGA0_XAB_RFInterfaceSW; | |
| /* 16 LSBs if read 32-bit from 0x874 */ | |
| priv->PHYRegDef[RF90_PATH_C].rfintfs = rFPGA0_XCD_RFInterfaceSW; | |
| /* 16 MSBs if read 32-bit from 0x874 (16-bit for 0x876) */ | |
| priv->PHYRegDef[RF90_PATH_D].rfintfs = rFPGA0_XCD_RFInterfaceSW; | |
| /* RF Interface Readback Value */ | |
| /* 16 LSBs if read 32-bit from 0x8E0 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfintfi = rFPGA0_XAB_RFInterfaceRB; | |
| /* 16 MSBs if read 32-bit from 0x8E0 (16-bit for 0x8E2) */ | |
| priv->PHYRegDef[RF90_PATH_B].rfintfi = rFPGA0_XAB_RFInterfaceRB; | |
| /* 16 LSBs if read 32-bit from 0x8E4 */ | |
| priv->PHYRegDef[RF90_PATH_C].rfintfi = rFPGA0_XCD_RFInterfaceRB; | |
| /* 16 MSBs if read 32-bit from 0x8E4 (16-bit for 0x8E6) */ | |
| priv->PHYRegDef[RF90_PATH_D].rfintfi = rFPGA0_XCD_RFInterfaceRB; | |
| /* RF Interface Output (and Enable) */ | |
| /* 16 LSBs if read 32-bit from 0x860 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfintfo = rFPGA0_XA_RFInterfaceOE; | |
| /* 16 LSBs if read 32-bit from 0x864 */ | |
| priv->PHYRegDef[RF90_PATH_B].rfintfo = rFPGA0_XB_RFInterfaceOE; | |
| /* 16 LSBs if read 32-bit from 0x868 */ | |
| priv->PHYRegDef[RF90_PATH_C].rfintfo = rFPGA0_XC_RFInterfaceOE; | |
| /* 16 LSBs if read 32-bit from 0x86C */ | |
| priv->PHYRegDef[RF90_PATH_D].rfintfo = rFPGA0_XD_RFInterfaceOE; | |
| /* RF Interface (Output and) Enable */ | |
| /* 16 MSBs if read 32-bit from 0x860 (16-bit for 0x862) */ | |
| priv->PHYRegDef[RF90_PATH_A].rfintfe = rFPGA0_XA_RFInterfaceOE; | |
| /* 16 MSBs if read 32-bit from 0x864 (16-bit for 0x866) */ | |
| priv->PHYRegDef[RF90_PATH_B].rfintfe = rFPGA0_XB_RFInterfaceOE; | |
| /* 16 MSBs if read 32-bit from 0x86A (16-bit for 0x86A) */ | |
| priv->PHYRegDef[RF90_PATH_C].rfintfe = rFPGA0_XC_RFInterfaceOE; | |
| /* 16 MSBs if read 32-bit from 0x86C (16-bit for 0x86E) */ | |
| priv->PHYRegDef[RF90_PATH_D].rfintfe = rFPGA0_XD_RFInterfaceOE; | |
| /* Addr of LSSI. Write RF register by driver */ | |
| priv->PHYRegDef[RF90_PATH_A].rf3wireOffset = rFPGA0_XA_LSSIParameter; | |
| priv->PHYRegDef[RF90_PATH_B].rf3wireOffset = rFPGA0_XB_LSSIParameter; | |
| priv->PHYRegDef[RF90_PATH_C].rf3wireOffset = rFPGA0_XC_LSSIParameter; | |
| priv->PHYRegDef[RF90_PATH_D].rf3wireOffset = rFPGA0_XD_LSSIParameter; | |
| /* RF parameter */ | |
| /* BB Band Select */ | |
| priv->PHYRegDef[RF90_PATH_A].rfLSSI_Select = rFPGA0_XAB_RFParameter; | |
| priv->PHYRegDef[RF90_PATH_B].rfLSSI_Select = rFPGA0_XAB_RFParameter; | |
| priv->PHYRegDef[RF90_PATH_C].rfLSSI_Select = rFPGA0_XCD_RFParameter; | |
| priv->PHYRegDef[RF90_PATH_D].rfLSSI_Select = rFPGA0_XCD_RFParameter; | |
| /* Tx AGC Gain Stage (same for all path. Should we remove this?) */ | |
| priv->PHYRegDef[RF90_PATH_A].rfTxGainStage = rFPGA0_TxGainStage; | |
| priv->PHYRegDef[RF90_PATH_B].rfTxGainStage = rFPGA0_TxGainStage; | |
| priv->PHYRegDef[RF90_PATH_C].rfTxGainStage = rFPGA0_TxGainStage; | |
| priv->PHYRegDef[RF90_PATH_D].rfTxGainStage = rFPGA0_TxGainStage; | |
| /* Tranceiver A~D HSSI Parameter-1 */ | |
| /* wire control parameter1 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfHSSIPara1 = rFPGA0_XA_HSSIParameter1; | |
| priv->PHYRegDef[RF90_PATH_B].rfHSSIPara1 = rFPGA0_XB_HSSIParameter1; | |
| priv->PHYRegDef[RF90_PATH_C].rfHSSIPara1 = rFPGA0_XC_HSSIParameter1; | |
| priv->PHYRegDef[RF90_PATH_D].rfHSSIPara1 = rFPGA0_XD_HSSIParameter1; | |
| /* Tranceiver A~D HSSI Parameter-2 */ | |
| /* wire control parameter2 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfHSSIPara2 = rFPGA0_XA_HSSIParameter2; | |
| priv->PHYRegDef[RF90_PATH_B].rfHSSIPara2 = rFPGA0_XB_HSSIParameter2; | |
| priv->PHYRegDef[RF90_PATH_C].rfHSSIPara2 = rFPGA0_XC_HSSIParameter2; | |
| priv->PHYRegDef[RF90_PATH_D].rfHSSIPara2 = rFPGA0_XD_HSSIParameter2; | |
| /* RF Switch Control */ | |
| /* TR/Ant switch control */ | |
| priv->PHYRegDef[RF90_PATH_A].rfSwitchControl = rFPGA0_XAB_SwitchControl; | |
| priv->PHYRegDef[RF90_PATH_B].rfSwitchControl = rFPGA0_XAB_SwitchControl; | |
| priv->PHYRegDef[RF90_PATH_C].rfSwitchControl = rFPGA0_XCD_SwitchControl; | |
| priv->PHYRegDef[RF90_PATH_D].rfSwitchControl = rFPGA0_XCD_SwitchControl; | |
| /* AGC control 1 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfAGCControl1 = rOFDM0_XAAGCCore1; | |
| priv->PHYRegDef[RF90_PATH_B].rfAGCControl1 = rOFDM0_XBAGCCore1; | |
| priv->PHYRegDef[RF90_PATH_C].rfAGCControl1 = rOFDM0_XCAGCCore1; | |
| priv->PHYRegDef[RF90_PATH_D].rfAGCControl1 = rOFDM0_XDAGCCore1; | |
| /* AGC control 2 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfAGCControl2 = rOFDM0_XAAGCCore2; | |
| priv->PHYRegDef[RF90_PATH_B].rfAGCControl2 = rOFDM0_XBAGCCore2; | |
| priv->PHYRegDef[RF90_PATH_C].rfAGCControl2 = rOFDM0_XCAGCCore2; | |
| priv->PHYRegDef[RF90_PATH_D].rfAGCControl2 = rOFDM0_XDAGCCore2; | |
| /* RX AFE control 1 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfRxIQImbalance = rOFDM0_XARxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_B].rfRxIQImbalance = rOFDM0_XBRxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_C].rfRxIQImbalance = rOFDM0_XCRxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_D].rfRxIQImbalance = rOFDM0_XDRxIQImbalance; | |
| /* RX AFE control 1 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfRxAFE = rOFDM0_XARxAFE; | |
| priv->PHYRegDef[RF90_PATH_B].rfRxAFE = rOFDM0_XBRxAFE; | |
| priv->PHYRegDef[RF90_PATH_C].rfRxAFE = rOFDM0_XCRxAFE; | |
| priv->PHYRegDef[RF90_PATH_D].rfRxAFE = rOFDM0_XDRxAFE; | |
| /* Tx AFE control 1 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfTxIQImbalance = rOFDM0_XATxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_B].rfTxIQImbalance = rOFDM0_XBTxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_C].rfTxIQImbalance = rOFDM0_XCTxIQImbalance; | |
| priv->PHYRegDef[RF90_PATH_D].rfTxIQImbalance = rOFDM0_XDTxIQImbalance; | |
| /* Tx AFE control 2 */ | |
| priv->PHYRegDef[RF90_PATH_A].rfTxAFE = rOFDM0_XATxAFE; | |
| priv->PHYRegDef[RF90_PATH_B].rfTxAFE = rOFDM0_XBTxAFE; | |
| priv->PHYRegDef[RF90_PATH_C].rfTxAFE = rOFDM0_XCTxAFE; | |
| priv->PHYRegDef[RF90_PATH_D].rfTxAFE = rOFDM0_XDTxAFE; | |
| /* Tranceiver LSSI Readback */ | |
| priv->PHYRegDef[RF90_PATH_A].rfLSSIReadBack = rFPGA0_XA_LSSIReadBack; | |
| priv->PHYRegDef[RF90_PATH_B].rfLSSIReadBack = rFPGA0_XB_LSSIReadBack; | |
| priv->PHYRegDef[RF90_PATH_C].rfLSSIReadBack = rFPGA0_XC_LSSIReadBack; | |
| priv->PHYRegDef[RF90_PATH_D].rfLSSIReadBack = rFPGA0_XD_LSSIReadBack; | |
| } | |
| /****************************************************************************** | |
| * function: This function is to write register and then readback to make | |
| * sure whether BB and RF is OK | |
| * input: net_device *dev | |
| * HW90_BLOCK_E CheckBlock | |
| * RF90_RADIO_PATH_E eRFPath //only used when checkblock is | |
| * //HW90_BLOCK_RF | |
| * output: none | |
| * return: return whether BB and RF is ok (0:OK, 1:Fail) | |
| * notice: This function may be removed in the ASIC | |
| ******************************************************************************/ | |
| u8 rtl8192_phy_checkBBAndRF(struct net_device *dev, HW90_BLOCK_E CheckBlock, | |
| RF90_RADIO_PATH_E eRFPath) | |
| { | |
| u8 ret = 0; | |
| u32 i, CheckTimes = 4, reg = 0; | |
| u32 WriteAddr[4]; | |
| u32 WriteData[] = {0xfffff027, 0xaa55a02f, 0x00000027, 0x55aa502f}; | |
| /* Initialize register address offset to be checked */ | |
| WriteAddr[HW90_BLOCK_MAC] = 0x100; | |
| WriteAddr[HW90_BLOCK_PHY0] = 0x900; | |
| WriteAddr[HW90_BLOCK_PHY1] = 0x800; | |
| WriteAddr[HW90_BLOCK_RF] = 0x3; | |
| RT_TRACE(COMP_PHY, "%s(), CheckBlock: %d\n", __func__, CheckBlock); | |
| for (i = 0; i < CheckTimes; i++) { | |
| /* Write data to register and readback */ | |
| switch (CheckBlock) { | |
| case HW90_BLOCK_MAC: | |
| RT_TRACE(COMP_ERR, | |
| "PHY_CheckBBRFOK(): Never Write 0x100 here!\n"); | |
| break; | |
| case HW90_BLOCK_PHY0: | |
| case HW90_BLOCK_PHY1: | |
| write_nic_dword(dev, WriteAddr[CheckBlock], | |
| WriteData[i]); | |
| read_nic_dword(dev, WriteAddr[CheckBlock], ®); | |
| break; | |
| case HW90_BLOCK_RF: | |
| WriteData[i] &= 0xfff; | |
| rtl8192_phy_SetRFReg(dev, eRFPath, | |
| WriteAddr[HW90_BLOCK_RF], | |
| bMask12Bits, WriteData[i]); | |
| /* TODO: we should not delay for such a long time. | |
| * Ask SD3 | |
| */ | |
| usleep_range(1000, 1000); | |
| reg = rtl8192_phy_QueryRFReg(dev, eRFPath, | |
| WriteAddr[HW90_BLOCK_RF], | |
| bMask12Bits); | |
| usleep_range(1000, 1000); | |
| break; | |
| default: | |
| ret = 1; | |
| break; | |
| } | |
| /* Check whether readback data is correct */ | |
| if (reg != WriteData[i]) { | |
| RT_TRACE((COMP_PHY|COMP_ERR), | |
| "error reg: %x, WriteData: %x\n", | |
| reg, WriteData[i]); | |
| ret = 1; | |
| break; | |
| } | |
| } | |
| return ret; | |
| } | |
| /****************************************************************************** | |
| * function: This function initializes BB&RF | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| * notice: Initialization value may change all the time, so please make | |
| * sure it has been synced with the newest. | |
| ******************************************************************************/ | |
| static void rtl8192_BB_Config_ParaFile(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u8 reg_u8 = 0, eCheckItem = 0, status = 0; | |
| u32 reg_u32 = 0; | |
| /************************************** | |
| * <1> Initialize BaseBand | |
| *************************************/ | |
| /* --set BB Global Reset-- */ | |
| read_nic_byte(dev, BB_GLOBAL_RESET, ®_u8); | |
| write_nic_byte(dev, BB_GLOBAL_RESET, (reg_u8|BB_GLOBAL_RESET_BIT)); | |
| mdelay(50); | |
| /* ---set BB reset Active--- */ | |
| read_nic_dword(dev, CPU_GEN, ®_u32); | |
| write_nic_dword(dev, CPU_GEN, (reg_u32&(~CPU_GEN_BB_RST))); | |
| /* ----Ckeck FPGAPHY0 and PHY1 board is OK---- */ | |
| /* TODO: this function should be removed on ASIC */ | |
| for (eCheckItem = (HW90_BLOCK_E)HW90_BLOCK_PHY0; | |
| eCheckItem <= HW90_BLOCK_PHY1; eCheckItem++) { | |
| /* don't care RF path */ | |
| status = rtl8192_phy_checkBBAndRF(dev, (HW90_BLOCK_E)eCheckItem, | |
| (RF90_RADIO_PATH_E)0); | |
| if (status != 0) { | |
| RT_TRACE((COMP_ERR | COMP_PHY), | |
| "PHY_RF8256_Config(): Check PHY%d Fail!!\n", | |
| eCheckItem-1); | |
| return; | |
| } | |
| } | |
| /* ---- Set CCK and OFDM Block "OFF"---- */ | |
| rtl8192_setBBreg(dev, rFPGA0_RFMOD, bCCKEn|bOFDMEn, 0x0); | |
| /* ----BB Register Initilazation---- */ | |
| /* ==m==>Set PHY REG From Header<==m== */ | |
| rtl8192_phyConfigBB(dev, BaseBand_Config_PHY_REG); | |
| /* ----Set BB reset de-Active---- */ | |
| read_nic_dword(dev, CPU_GEN, ®_u32); | |
| write_nic_dword(dev, CPU_GEN, (reg_u32|CPU_GEN_BB_RST)); | |
| /* ----BB AGC table Initialization---- */ | |
| /* ==m==>Set PHY REG From Header<==m== */ | |
| rtl8192_phyConfigBB(dev, BaseBand_Config_AGC_TAB); | |
| /* ----Enable XSTAL ---- */ | |
| write_nic_byte_E(dev, 0x5e, 0x00); | |
| if (priv->card_8192_version == (u8)VERSION_819xU_A) { | |
| /* Antenna gain offset from B/C/D to A */ | |
| reg_u32 = priv->AntennaTxPwDiff[1]<<4 | | |
| priv->AntennaTxPwDiff[0]; | |
| rtl8192_setBBreg(dev, rFPGA0_TxGainStage, (bXBTxAGC|bXCTxAGC), | |
| reg_u32); | |
| /* XSTALLCap */ | |
| reg_u32 = priv->CrystalCap & 0xf; | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bXtalCap, | |
| reg_u32); | |
| } | |
| /* Check if the CCK HighPower is turned ON. | |
| * This is used to calculate PWDB. | |
| */ | |
| priv->bCckHighPower = (u8)rtl8192_QueryBBReg(dev, | |
| rFPGA0_XA_HSSIParameter2, | |
| 0x200); | |
| } | |
| /****************************************************************************** | |
| * function: This function initializes BB&RF | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| * notice: Initialization value may change all the time, so please make | |
| * sure it has been synced with the newest. | |
| *****************************************************************************/ | |
| void rtl8192_BBConfig(struct net_device *dev) | |
| { | |
| rtl8192_InitBBRFRegDef(dev); | |
| /* config BB&RF. As hardCode based initialization has not been well | |
| * implemented, so use file first. | |
| * FIXME: should implement it for hardcode? | |
| */ | |
| rtl8192_BB_Config_ParaFile(dev); | |
| } | |
| /****************************************************************************** | |
| * function: This function obtains the initialization value of Tx power Level | |
| * offset | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| *****************************************************************************/ | |
| void rtl8192_phy_getTxPower(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u8 tmp; | |
| read_nic_dword(dev, rTxAGC_Rate18_06, | |
| &priv->MCSTxPowerLevelOriginalOffset[0]); | |
| read_nic_dword(dev, rTxAGC_Rate54_24, | |
| &priv->MCSTxPowerLevelOriginalOffset[1]); | |
| read_nic_dword(dev, rTxAGC_Mcs03_Mcs00, | |
| &priv->MCSTxPowerLevelOriginalOffset[2]); | |
| read_nic_dword(dev, rTxAGC_Mcs07_Mcs04, | |
| &priv->MCSTxPowerLevelOriginalOffset[3]); | |
| read_nic_dword(dev, rTxAGC_Mcs11_Mcs08, | |
| &priv->MCSTxPowerLevelOriginalOffset[4]); | |
| read_nic_dword(dev, rTxAGC_Mcs15_Mcs12, | |
| &priv->MCSTxPowerLevelOriginalOffset[5]); | |
| /* Read rx initial gain */ | |
| read_nic_byte(dev, rOFDM0_XAAGCCore1, &priv->DefaultInitialGain[0]); | |
| read_nic_byte(dev, rOFDM0_XBAGCCore1, &priv->DefaultInitialGain[1]); | |
| read_nic_byte(dev, rOFDM0_XCAGCCore1, &priv->DefaultInitialGain[2]); | |
| read_nic_byte(dev, rOFDM0_XDAGCCore1, &priv->DefaultInitialGain[3]); | |
| RT_TRACE(COMP_INIT, | |
| "Default initial gain (c50=0x%x, c58=0x%x, c60=0x%x, c68=0x%x)\n", | |
| priv->DefaultInitialGain[0], priv->DefaultInitialGain[1], | |
| priv->DefaultInitialGain[2], priv->DefaultInitialGain[3]); | |
| /* Read framesync */ | |
| read_nic_byte(dev, rOFDM0_RxDetector3, &priv->framesync); | |
| read_nic_byte(dev, rOFDM0_RxDetector2, &tmp); | |
| priv->framesyncC34 = tmp; | |
| RT_TRACE(COMP_INIT, "Default framesync (0x%x) = 0x%x\n", | |
| rOFDM0_RxDetector3, priv->framesync); | |
| /* Read SIFS (save the value read fome MACPHY_REG.txt) */ | |
| read_nic_word(dev, SIFS, &priv->SifsTime); | |
| } | |
| /****************************************************************************** | |
| * function: This function sets the initialization value of Tx power Level | |
| * offset | |
| * input: net_device *dev | |
| * u8 channel | |
| * output: none | |
| * return: none | |
| ******************************************************************************/ | |
| void rtl8192_phy_setTxPower(struct net_device *dev, u8 channel) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u8 powerlevel = priv->TxPowerLevelCCK[channel-1]; | |
| u8 powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1]; | |
| switch (priv->rf_chip) { | |
| case RF_8256: | |
| /* need further implement */ | |
| PHY_SetRF8256CCKTxPower(dev, powerlevel); | |
| PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G); | |
| break; | |
| default: | |
| RT_TRACE((COMP_PHY|COMP_ERR), | |
| "error RF chipID(8225 or 8258) in function %s()\n", | |
| __func__); | |
| break; | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function checks Rf chip to do RF config | |
| * input: net_device *dev | |
| * output: none | |
| * return: only 8256 is supported | |
| ******************************************************************************/ | |
| void rtl8192_phy_RFConfig(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| switch (priv->rf_chip) { | |
| case RF_8256: | |
| PHY_RF8256_Config(dev); | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, "error chip id\n"); | |
| break; | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function updates Initial gain | |
| * input: net_device *dev | |
| * output: none | |
| * return: As Windows has not implemented this, wait for complement | |
| ******************************************************************************/ | |
| void rtl8192_phy_updateInitGain(struct net_device *dev) | |
| { | |
| } | |
| /****************************************************************************** | |
| * function: This function read RF parameters from general head file, | |
| * and do RF 3-wire | |
| * input: net_device *dev | |
| * RF90_RADIO_PATH_E eRFPath | |
| * output: none | |
| * return: return code show if RF configuration is successful(0:pass, 1:fail) | |
| * notice: Delay may be required for RF configuration | |
| *****************************************************************************/ | |
| u8 rtl8192_phy_ConfigRFWithHeaderFile(struct net_device *dev, | |
| RF90_RADIO_PATH_E eRFPath) | |
| { | |
| int i; | |
| switch (eRFPath) { | |
| case RF90_PATH_A: | |
| for (i = 0; i < RadioA_ArrayLength; i = i+2) { | |
| if (rtl819XRadioA_Array[i] == 0xfe) { | |
| mdelay(100); | |
| continue; | |
| } | |
| rtl8192_phy_SetRFReg(dev, eRFPath, | |
| rtl819XRadioA_Array[i], | |
| bMask12Bits, | |
| rtl819XRadioA_Array[i+1]); | |
| mdelay(1); | |
| } | |
| break; | |
| case RF90_PATH_B: | |
| for (i = 0; i < RadioB_ArrayLength; i = i+2) { | |
| if (rtl819XRadioB_Array[i] == 0xfe) { | |
| mdelay(100); | |
| continue; | |
| } | |
| rtl8192_phy_SetRFReg(dev, eRFPath, | |
| rtl819XRadioB_Array[i], | |
| bMask12Bits, | |
| rtl819XRadioB_Array[i+1]); | |
| mdelay(1); | |
| } | |
| break; | |
| case RF90_PATH_C: | |
| for (i = 0; i < RadioC_ArrayLength; i = i+2) { | |
| if (rtl819XRadioC_Array[i] == 0xfe) { | |
| mdelay(100); | |
| continue; | |
| } | |
| rtl8192_phy_SetRFReg(dev, eRFPath, | |
| rtl819XRadioC_Array[i], | |
| bMask12Bits, | |
| rtl819XRadioC_Array[i+1]); | |
| mdelay(1); | |
| } | |
| break; | |
| case RF90_PATH_D: | |
| for (i = 0; i < RadioD_ArrayLength; i = i+2) { | |
| if (rtl819XRadioD_Array[i] == 0xfe) { | |
| mdelay(100); | |
| continue; | |
| } | |
| rtl8192_phy_SetRFReg(dev, eRFPath, | |
| rtl819XRadioD_Array[i], | |
| bMask12Bits, | |
| rtl819XRadioD_Array[i+1]); | |
| mdelay(1); | |
| } | |
| break; | |
| default: | |
| break; | |
| } | |
| return 0; | |
| } | |
| /****************************************************************************** | |
| * function: This function sets Tx Power of the channel | |
| * input: net_device *dev | |
| * u8 channel | |
| * output: none | |
| * return: none | |
| * notice: | |
| ******************************************************************************/ | |
| static void rtl8192_SetTxPowerLevel(struct net_device *dev, u8 channel) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u8 powerlevel = priv->TxPowerLevelCCK[channel-1]; | |
| u8 powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1]; | |
| switch (priv->rf_chip) { | |
| case RF_8225: | |
| #ifdef TO_DO_LIST | |
| PHY_SetRF8225CckTxPower(Adapter, powerlevel); | |
| PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G); | |
| #endif | |
| break; | |
| case RF_8256: | |
| PHY_SetRF8256CCKTxPower(dev, powerlevel); | |
| PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G); | |
| break; | |
| case RF_8258: | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, "unknown rf chip ID in %s()\n", __func__); | |
| break; | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: This function sets RF state on or off | |
| * input: net_device *dev | |
| * RT_RF_POWER_STATE eRFPowerState //Power State to set | |
| * output: none | |
| * return: none | |
| * notice: | |
| *****************************************************************************/ | |
| bool rtl8192_SetRFPowerState(struct net_device *dev, | |
| RT_RF_POWER_STATE eRFPowerState) | |
| { | |
| bool bResult = true; | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| if (eRFPowerState == priv->ieee80211->eRFPowerState) | |
| return false; | |
| if (priv->SetRFPowerStateInProgress) | |
| return false; | |
| priv->SetRFPowerStateInProgress = true; | |
| switch (priv->rf_chip) { | |
| case RF_8256: | |
| switch (eRFPowerState) { | |
| case eRfOn: | |
| /* RF-A, RF-B */ | |
| /* enable RF-Chip A/B - 0x860[4] */ | |
| rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT(4), | |
| 0x1); | |
| /* analog to digital on - 0x88c[9:8] */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300, | |
| 0x3); | |
| /* digital to analog on - 0x880[4:3] */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18, | |
| 0x3); | |
| /* rx antenna on - 0xc04[1:0] */ | |
| rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0x3, 0x3); | |
| /* rx antenna on - 0xd04[1:0] */ | |
| rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0x3, 0x3); | |
| /* analog to digital part2 on - 0x880[6:5] */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60, | |
| 0x3); | |
| break; | |
| case eRfSleep: | |
| break; | |
| case eRfOff: | |
| /* RF-A, RF-B */ | |
| /* disable RF-Chip A/B - 0x860[4] */ | |
| rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT(4), | |
| 0x0); | |
| /* analog to digital off, for power save */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00, | |
| 0x0); /* 0x88c[11:8] */ | |
| /* digital to analog off, for power save - 0x880[4:3] */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18, | |
| 0x0); | |
| /* rx antenna off - 0xc04[3:0] */ | |
| rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0xf, 0x0); | |
| /* rx antenna off - 0xd04[3:0] */ | |
| rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x0); | |
| /* analog to digital part2 off, for power save */ | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60, | |
| 0x0); /* 0x880[6:5] */ | |
| break; | |
| default: | |
| bResult = false; | |
| RT_TRACE(COMP_ERR, "%s(): unknown state to set: 0x%X\n", | |
| __func__, eRFPowerState); | |
| break; | |
| } | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, "Not support rf_chip(%x)\n", priv->rf_chip); | |
| break; | |
| } | |
| #ifdef TO_DO_LIST | |
| if (bResult) { | |
| /* Update current RF state variable. */ | |
| pHalData->eRFPowerState = eRFPowerState; | |
| switch (pHalData->RFChipID) { | |
| case RF_8256: | |
| switch (pHalData->eRFPowerState) { | |
| case eRfOff: | |
| /* If Rf off reason is from IPS, | |
| * LED should blink with no link | |
| */ | |
| if (pMgntInfo->RfOffReason == RF_CHANGE_BY_IPS) | |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_NO_LINK); | |
| else | |
| /* Turn off LED if RF is not ON. */ | |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_POWER_OFF); | |
| break; | |
| case eRfOn: | |
| /* Turn on RF we are still linked, which might | |
| * happen when we quickly turn off and on HW RF. | |
| */ | |
| if (pMgntInfo->bMediaConnect) | |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_LINK); | |
| else | |
| /* Turn off LED if RF is not ON. */ | |
| Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_NO_LINK); | |
| break; | |
| default: | |
| break; | |
| } | |
| break; | |
| default: | |
| RT_TRACE(COMP_RF, DBG_LOUD, "%s(): Unknown RF type\n", | |
| __func__); | |
| break; | |
| } | |
| } | |
| #endif | |
| priv->SetRFPowerStateInProgress = false; | |
| return bResult; | |
| } | |
| /****************************************************************************** | |
| * function: This function sets command table variable (struct SwChnlCmd). | |
| * input: SwChnlCmd *CmdTable //table to be set | |
| * u32 CmdTableIdx //variable index in table to be set | |
| * u32 CmdTableSz //table size | |
| * SwChnlCmdID CmdID //command ID to set | |
| * u32 Para1 | |
| * u32 Para2 | |
| * u32 msDelay | |
| * output: | |
| * return: true if finished, false otherwise | |
| * notice: | |
| ******************************************************************************/ | |
| static u8 rtl8192_phy_SetSwChnlCmdArray(SwChnlCmd *CmdTable, u32 CmdTableIdx, | |
| u32 CmdTableSz, SwChnlCmdID CmdID, | |
| u32 Para1, u32 Para2, u32 msDelay) | |
| { | |
| SwChnlCmd *pCmd; | |
| if (CmdTable == NULL) { | |
| RT_TRACE(COMP_ERR, "%s(): CmdTable cannot be NULL\n", __func__); | |
| return false; | |
| } | |
| if (CmdTableIdx >= CmdTableSz) { | |
| RT_TRACE(COMP_ERR, "%s(): Access invalid index, please check size of the table, CmdTableIdx:%d, CmdTableSz:%d\n", | |
| __func__, CmdTableIdx, CmdTableSz); | |
| return false; | |
| } | |
| pCmd = CmdTable + CmdTableIdx; | |
| pCmd->CmdID = CmdID; | |
| pCmd->Para1 = Para1; | |
| pCmd->Para2 = Para2; | |
| pCmd->msDelay = msDelay; | |
| return true; | |
| } | |
| /****************************************************************************** | |
| * function: This function sets channel step by step | |
| * input: net_device *dev | |
| * u8 channel | |
| * u8 *stage //3 stages | |
| * u8 *step | |
| * u32 *delay //whether need to delay | |
| * output: store new stage, step and delay for next step | |
| * (combine with function above) | |
| * return: true if finished, false otherwise | |
| * notice: Wait for simpler function to replace it | |
| *****************************************************************************/ | |
| static u8 rtl8192_phy_SwChnlStepByStep(struct net_device *dev, u8 channel, | |
| u8 *stage, u8 *step, u32 *delay) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| SwChnlCmd PreCommonCmd[MAX_PRECMD_CNT]; | |
| u32 PreCommonCmdCnt; | |
| SwChnlCmd PostCommonCmd[MAX_POSTCMD_CNT]; | |
| u32 PostCommonCmdCnt; | |
| SwChnlCmd RfDependCmd[MAX_RFDEPENDCMD_CNT]; | |
| u32 RfDependCmdCnt; | |
| SwChnlCmd *CurrentCmd = NULL; | |
| u8 eRFPath; | |
| RT_TRACE(COMP_CH, "%s() stage: %d, step: %d, channel: %d\n", | |
| __func__, *stage, *step, channel); | |
| if (!IsLegalChannel(priv->ieee80211, channel)) { | |
| RT_TRACE(COMP_ERR, "set to illegal channel: %d\n", channel); | |
| /* return true to tell upper caller function this channel | |
| * setting is finished! Or it will in while loop. | |
| */ | |
| return true; | |
| } | |
| /* FIXME: need to check whether channel is legal or not here */ | |
| /* <1> Fill up pre common command. */ | |
| PreCommonCmdCnt = 0; | |
| rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++, | |
| MAX_PRECMD_CNT, CmdID_SetTxPowerLevel, | |
| 0, 0, 0); | |
| rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++, | |
| MAX_PRECMD_CNT, CmdID_End, 0, 0, 0); | |
| /* <2> Fill up post common command. */ | |
| PostCommonCmdCnt = 0; | |
| rtl8192_phy_SetSwChnlCmdArray(PostCommonCmd, PostCommonCmdCnt++, | |
| MAX_POSTCMD_CNT, CmdID_End, 0, 0, 0); | |
| /* <3> Fill up RF dependent command. */ | |
| RfDependCmdCnt = 0; | |
| switch (priv->rf_chip) { | |
| case RF_8225: | |
| if (!(channel >= 1 && channel <= 14)) { | |
| RT_TRACE(COMP_ERR, | |
| "illegal channel for Zebra 8225: %d\n", | |
| channel); | |
| return true; | |
| } | |
| rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, | |
| MAX_RFDEPENDCMD_CNT, | |
| CmdID_RF_WriteReg, | |
| rZebra1_Channel, | |
| RF_CHANNEL_TABLE_ZEBRA[channel], | |
| 10); | |
| rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, | |
| MAX_RFDEPENDCMD_CNT, | |
| CmdID_End, 0, 0, 0); | |
| break; | |
| case RF_8256: | |
| /* TEST!! This is not the table for 8256!! */ | |
| if (!(channel >= 1 && channel <= 14)) { | |
| RT_TRACE(COMP_ERR, | |
| "illegal channel for Zebra 8256: %d\n", | |
| channel); | |
| return true; | |
| } | |
| rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, | |
| MAX_RFDEPENDCMD_CNT, | |
| CmdID_RF_WriteReg, | |
| rZebra1_Channel, channel, 10); | |
| rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++, | |
| MAX_RFDEPENDCMD_CNT, | |
| CmdID_End, 0, 0, 0); | |
| break; | |
| case RF_8258: | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip); | |
| return true; | |
| } | |
| do { | |
| switch (*stage) { | |
| case 0: | |
| CurrentCmd = &PreCommonCmd[*step]; | |
| break; | |
| case 1: | |
| CurrentCmd = &RfDependCmd[*step]; | |
| break; | |
| case 2: | |
| CurrentCmd = &PostCommonCmd[*step]; | |
| break; | |
| } | |
| if (CurrentCmd->CmdID == CmdID_End) { | |
| if ((*stage) == 2) { | |
| (*delay) = CurrentCmd->msDelay; | |
| return true; | |
| } | |
| (*stage)++; | |
| (*step) = 0; | |
| continue; | |
| } | |
| switch (CurrentCmd->CmdID) { | |
| case CmdID_SetTxPowerLevel: | |
| if (priv->card_8192_version == (u8)VERSION_819xU_A) | |
| /* consider it later! */ | |
| rtl8192_SetTxPowerLevel(dev, channel); | |
| break; | |
| case CmdID_WritePortUlong: | |
| write_nic_dword(dev, CurrentCmd->Para1, | |
| CurrentCmd->Para2); | |
| break; | |
| case CmdID_WritePortUshort: | |
| write_nic_word(dev, CurrentCmd->Para1, | |
| (u16)CurrentCmd->Para2); | |
| break; | |
| case CmdID_WritePortUchar: | |
| write_nic_byte(dev, CurrentCmd->Para1, | |
| (u8)CurrentCmd->Para2); | |
| break; | |
| case CmdID_RF_WriteReg: | |
| for (eRFPath = 0; eRFPath < RF90_PATH_MAX; eRFPath++) { | |
| rtl8192_phy_SetRFReg(dev, | |
| (RF90_RADIO_PATH_E)eRFPath, | |
| CurrentCmd->Para1, | |
| bZebra1_ChannelNum, | |
| CurrentCmd->Para2); | |
| } | |
| break; | |
| default: | |
| break; | |
| } | |
| break; | |
| } while (true); | |
| (*delay) = CurrentCmd->msDelay; | |
| (*step)++; | |
| return false; | |
| } | |
| /****************************************************************************** | |
| * function: This function does actually set channel work | |
| * input: net_device *dev | |
| * u8 channel | |
| * output: none | |
| * return: none | |
| * notice: We should not call this function directly | |
| *****************************************************************************/ | |
| static void rtl8192_phy_FinishSwChnlNow(struct net_device *dev, u8 channel) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u32 delay = 0; | |
| while (!rtl8192_phy_SwChnlStepByStep(dev, channel, &priv->SwChnlStage, | |
| &priv->SwChnlStep, &delay)) { | |
| if (!priv->up) | |
| break; | |
| } | |
| } | |
| /****************************************************************************** | |
| * function: Callback routine of the work item for switch channel. | |
| * input: net_device *dev | |
| * | |
| * output: none | |
| * return: none | |
| *****************************************************************************/ | |
| void rtl8192_SwChnl_WorkItem(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| RT_TRACE(COMP_CH, "==> SwChnlCallback819xUsbWorkItem(), chan:%d\n", | |
| priv->chan); | |
| rtl8192_phy_FinishSwChnlNow(dev, priv->chan); | |
| RT_TRACE(COMP_CH, "<== SwChnlCallback819xUsbWorkItem()\n"); | |
| } | |
| /****************************************************************************** | |
| * function: This function scheduled actual work item to set channel | |
| * input: net_device *dev | |
| * u8 channel //channel to set | |
| * output: none | |
| * return: return code show if workitem is scheduled (1:pass, 0:fail) | |
| * notice: Delay may be required for RF configuration | |
| ******************************************************************************/ | |
| u8 rtl8192_phy_SwChnl(struct net_device *dev, u8 channel) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| RT_TRACE(COMP_CH, "%s(), SwChnlInProgress: %d\n", __func__, | |
| priv->SwChnlInProgress); | |
| if (!priv->up) | |
| return false; | |
| if (priv->SwChnlInProgress) | |
| return false; | |
| /* -------------------------------------------- */ | |
| switch (priv->ieee80211->mode) { | |
| case WIRELESS_MODE_A: | |
| case WIRELESS_MODE_N_5G: | |
| if (channel <= 14) { | |
| RT_TRACE(COMP_ERR, "WIRELESS_MODE_A but channel<=14\n"); | |
| return false; | |
| } | |
| break; | |
| case WIRELESS_MODE_B: | |
| if (channel > 14) { | |
| RT_TRACE(COMP_ERR, "WIRELESS_MODE_B but channel>14\n"); | |
| return false; | |
| } | |
| break; | |
| case WIRELESS_MODE_G: | |
| case WIRELESS_MODE_N_24G: | |
| if (channel > 14) { | |
| RT_TRACE(COMP_ERR, "WIRELESS_MODE_G but channel>14\n"); | |
| return false; | |
| } | |
| break; | |
| } | |
| /* -------------------------------------------- */ | |
| priv->SwChnlInProgress = true; | |
| if (channel == 0) | |
| channel = 1; | |
| priv->chan = channel; | |
| priv->SwChnlStage = 0; | |
| priv->SwChnlStep = 0; | |
| if (priv->up) | |
| rtl8192_SwChnl_WorkItem(dev); | |
| priv->SwChnlInProgress = false; | |
| return true; | |
| } | |
| /****************************************************************************** | |
| * function: Callback routine of the work item for set bandwidth mode. | |
| * input: net_device *dev | |
| * output: none | |
| * return: none | |
| * notice: I doubt whether SetBWModeInProgress flag is necessary as we can | |
| * test whether current work in the queue or not.//do I? | |
| *****************************************************************************/ | |
| void rtl8192_SetBWModeWorkItem(struct net_device *dev) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| u8 regBwOpMode; | |
| RT_TRACE(COMP_SWBW, "%s() Switch to %s bandwidth\n", __func__, | |
| priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20?"20MHz":"40MHz"); | |
| if (priv->rf_chip == RF_PSEUDO_11N) { | |
| priv->SetBWModeInProgress = false; | |
| return; | |
| } | |
| /* <1> Set MAC register */ | |
| read_nic_byte(dev, BW_OPMODE, ®BwOpMode); | |
| switch (priv->CurrentChannelBW) { | |
| case HT_CHANNEL_WIDTH_20: | |
| regBwOpMode |= BW_OPMODE_20MHZ; | |
| /* We have not verify whether this register works */ | |
| write_nic_byte(dev, BW_OPMODE, regBwOpMode); | |
| break; | |
| case HT_CHANNEL_WIDTH_20_40: | |
| regBwOpMode &= ~BW_OPMODE_20MHZ; | |
| /* We have not verify whether this register works */ | |
| write_nic_byte(dev, BW_OPMODE, regBwOpMode); | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, | |
| "SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n", | |
| priv->CurrentChannelBW); | |
| break; | |
| } | |
| /* <2> Set PHY related register */ | |
| switch (priv->CurrentChannelBW) { | |
| case HT_CHANNEL_WIDTH_20: | |
| rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x0); | |
| rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x0); | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, | |
| 0x00100000, 1); | |
| /* Correct the tx power for CCK rate in 20M. */ | |
| priv->cck_present_attenuation = | |
| priv->cck_present_attenuation_20Mdefault + | |
| priv->cck_present_attenuation_difference; | |
| if (priv->cck_present_attenuation > 22) | |
| priv->cck_present_attenuation = 22; | |
| if (priv->cck_present_attenuation < 0) | |
| priv->cck_present_attenuation = 0; | |
| RT_TRACE(COMP_INIT, | |
| "20M, pHalData->CCKPresentAttentuation = %d\n", | |
| priv->cck_present_attenuation); | |
| if (priv->chan == 14 && !priv->bcck_in_ch14) { | |
| priv->bcck_in_ch14 = true; | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } else if (priv->chan != 14 && priv->bcck_in_ch14) { | |
| priv->bcck_in_ch14 = false; | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } else { | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } | |
| break; | |
| case HT_CHANNEL_WIDTH_20_40: | |
| rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x1); | |
| rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x1); | |
| rtl8192_setBBreg(dev, rCCK0_System, bCCKSideBand, | |
| priv->nCur40MhzPrimeSC>>1); | |
| rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 0); | |
| rtl8192_setBBreg(dev, rOFDM1_LSTF, 0xC00, | |
| priv->nCur40MhzPrimeSC); | |
| priv->cck_present_attenuation = | |
| priv->cck_present_attenuation_40Mdefault + | |
| priv->cck_present_attenuation_difference; | |
| if (priv->cck_present_attenuation > 22) | |
| priv->cck_present_attenuation = 22; | |
| if (priv->cck_present_attenuation < 0) | |
| priv->cck_present_attenuation = 0; | |
| RT_TRACE(COMP_INIT, | |
| "40M, pHalData->CCKPresentAttentuation = %d\n", | |
| priv->cck_present_attenuation); | |
| if (priv->chan == 14 && !priv->bcck_in_ch14) { | |
| priv->bcck_in_ch14 = true; | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } else if (priv->chan != 14 && priv->bcck_in_ch14) { | |
| priv->bcck_in_ch14 = false; | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } else { | |
| dm_cck_txpower_adjust(dev, priv->bcck_in_ch14); | |
| } | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, | |
| "SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n", | |
| priv->CurrentChannelBW); | |
| break; | |
| } | |
| /* Skip over setting of J-mode in BB register here. | |
| * Default value is "None J mode". | |
| */ | |
| /* <3> Set RF related register */ | |
| switch (priv->rf_chip) { | |
| case RF_8225: | |
| #ifdef TO_DO_LIST | |
| PHY_SetRF8225Bandwidth(Adapter, pHalData->CurrentChannelBW); | |
| #endif | |
| break; | |
| case RF_8256: | |
| PHY_SetRF8256Bandwidth(dev, priv->CurrentChannelBW); | |
| break; | |
| case RF_8258: | |
| break; | |
| case RF_PSEUDO_11N: | |
| break; | |
| default: | |
| RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip); | |
| break; | |
| } | |
| priv->SetBWModeInProgress = false; | |
| RT_TRACE(COMP_SWBW, "<==SetBWMode819xUsb(), %d\n", | |
| atomic_read(&priv->ieee80211->atm_swbw)); | |
| } | |
| /****************************************************************************** | |
| * function: This function schedules bandwidth switch work. | |
| * input: struct net_deviceq *dev | |
| * HT_CHANNEL_WIDTH bandwidth //20M or 40M | |
| * HT_EXTCHNL_OFFSET offset //Upper, Lower, or Don't care | |
| * output: none | |
| * return: none | |
| * notice: I doubt whether SetBWModeInProgress flag is necessary as we can | |
| * test whether current work in the queue or not.//do I? | |
| *****************************************************************************/ | |
| void rtl8192_SetBWMode(struct net_device *dev, HT_CHANNEL_WIDTH bandwidth, | |
| HT_EXTCHNL_OFFSET offset) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| if (priv->SetBWModeInProgress) | |
| return; | |
| priv->SetBWModeInProgress = true; | |
| priv->CurrentChannelBW = bandwidth; | |
| if (offset == HT_EXTCHNL_OFFSET_LOWER) | |
| priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_UPPER; | |
| else if (offset == HT_EXTCHNL_OFFSET_UPPER) | |
| priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_LOWER; | |
| else | |
| priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_DONT_CARE; | |
| rtl8192_SetBWModeWorkItem(dev); | |
| } | |
| void InitialGain819xUsb(struct net_device *dev, u8 Operation) | |
| { | |
| struct r8192_priv *priv = ieee80211_priv(dev); | |
| priv->InitialGainOperateType = Operation; | |
| if (priv->up) | |
| queue_delayed_work(priv->priv_wq, &priv->initialgain_operate_wq, 0); | |
| } | |
| void InitialGainOperateWorkItemCallBack(struct work_struct *work) | |
| { | |
| struct delayed_work *dwork = to_delayed_work(work); | |
| struct r8192_priv *priv = container_of(dwork, struct r8192_priv, | |
| initialgain_operate_wq); | |
| struct net_device *dev = priv->ieee80211->dev; | |
| #define SCAN_RX_INITIAL_GAIN 0x17 | |
| #define POWER_DETECTION_TH 0x08 | |
| u32 bitmask; | |
| u8 initial_gain; | |
| u8 Operation; | |
| Operation = priv->InitialGainOperateType; | |
| switch (Operation) { | |
| case IG_Backup: | |
| RT_TRACE(COMP_SCAN, "IG_Backup, backup the initial gain.\n"); | |
| initial_gain = SCAN_RX_INITIAL_GAIN; | |
| bitmask = bMaskByte0; | |
| if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM) | |
| /* FW DIG OFF */ | |
| rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8); | |
| priv->initgain_backup.xaagccore1 = | |
| (u8)rtl8192_QueryBBReg(dev, rOFDM0_XAAGCCore1, bitmask); | |
| priv->initgain_backup.xbagccore1 = | |
| (u8)rtl8192_QueryBBReg(dev, rOFDM0_XBAGCCore1, bitmask); | |
| priv->initgain_backup.xcagccore1 = | |
| (u8)rtl8192_QueryBBReg(dev, rOFDM0_XCAGCCore1, bitmask); | |
| priv->initgain_backup.xdagccore1 = | |
| (u8)rtl8192_QueryBBReg(dev, rOFDM0_XDAGCCore1, bitmask); | |
| bitmask = bMaskByte2; | |
| priv->initgain_backup.cca = | |
| (u8)rtl8192_QueryBBReg(dev, rCCK0_CCA, bitmask); | |
| RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc50 is %x\n", | |
| priv->initgain_backup.xaagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc58 is %x\n", | |
| priv->initgain_backup.xbagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc60 is %x\n", | |
| priv->initgain_backup.xcagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc68 is %x\n", | |
| priv->initgain_backup.xdagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xa0a is %x\n", | |
| priv->initgain_backup.cca); | |
| RT_TRACE(COMP_SCAN, "Write scan initial gain = 0x%x\n", | |
| initial_gain); | |
| write_nic_byte(dev, rOFDM0_XAAGCCore1, initial_gain); | |
| write_nic_byte(dev, rOFDM0_XBAGCCore1, initial_gain); | |
| write_nic_byte(dev, rOFDM0_XCAGCCore1, initial_gain); | |
| write_nic_byte(dev, rOFDM0_XDAGCCore1, initial_gain); | |
| RT_TRACE(COMP_SCAN, "Write scan 0xa0a = 0x%x\n", | |
| POWER_DETECTION_TH); | |
| write_nic_byte(dev, 0xa0a, POWER_DETECTION_TH); | |
| break; | |
| case IG_Restore: | |
| RT_TRACE(COMP_SCAN, "IG_Restore, restore the initial gain.\n"); | |
| bitmask = 0x7f; /* Bit0 ~ Bit6 */ | |
| if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM) | |
| /* FW DIG OFF */ | |
| rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8); | |
| rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bitmask, | |
| (u32)priv->initgain_backup.xaagccore1); | |
| rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bitmask, | |
| (u32)priv->initgain_backup.xbagccore1); | |
| rtl8192_setBBreg(dev, rOFDM0_XCAGCCore1, bitmask, | |
| (u32)priv->initgain_backup.xcagccore1); | |
| rtl8192_setBBreg(dev, rOFDM0_XDAGCCore1, bitmask, | |
| (u32)priv->initgain_backup.xdagccore1); | |
| bitmask = bMaskByte2; | |
| rtl8192_setBBreg(dev, rCCK0_CCA, bitmask, | |
| (u32)priv->initgain_backup.cca); | |
| RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc50 is %x\n", | |
| priv->initgain_backup.xaagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc58 is %x\n", | |
| priv->initgain_backup.xbagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc60 is %x\n", | |
| priv->initgain_backup.xcagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc68 is %x\n", | |
| priv->initgain_backup.xdagccore1); | |
| RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xa0a is %x\n", | |
| priv->initgain_backup.cca); | |
| rtl8192_phy_setTxPower(dev, priv->ieee80211->current_network.channel); | |
| if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM) | |
| /* FW DIG ON */ | |
| rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x1); | |
| break; | |
| default: | |
| RT_TRACE(COMP_SCAN, "Unknown IG Operation.\n"); | |
| break; | |
| } | |
| } |