tree a83f85367817aac24f098efb904a98ba9337fede
parent 5b167c123b3c3582f62cf1896465019bc40fe526
author Maciej W. Rozycki <macro@linux-mips.org> 1378168198 +0100
committer Ralf Baechle <ralf@linux-mips.org> 1378212242 +0200

MIPS: R4k clock source initialization bug fix

This is a fix for a bug introduced with commit
447cdf2628b59aa513a42785450b348dced26d8a, submitted as archived here:
http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20080312235002.c717dde3.yoichi_yuasa%40tripeaks.co.jp
regrettably with no further explanation.

The issue is with the CP0 Count register read erratum present on R4000 and
some R4400 processors.  If this erratum is present, then a read from this
register that happens around the time it reaches the value stored in the
CP0 Compare register causes a CP0 timer interrupt that is supposed to
happen when the values in the two registers match to be missed.  The
implication for the chips affected is the CP0 timer can be used either as
a source of a timer interrupt (a clock event) or as a source of a
high-resolution counter (a clock source), but not both at a time.

The erratum does not affect timer interrupt operation itself, because in
this case the CP0 Count register is only read while the timer interrupt
has already been raised, while high-resolution counter references happen
at random times.

Additionally some systems apparently have issues with the timer interrupt
line being routed externally and not following the usual CP0 Count/Compare
semantics.  In this case we don't want to use the R4k clock event.

We've meant to address the erratum and the timer interrupt routing issue
in time_init, however the commit referred to above broke our solution.
What we currently have is we enable the R4k clock source if the R4k clock
event initialization has succeeded (the timer is present and has no timer
interrupt routing issue) or there is no CP0 Count register read erratum.
Which gives the following boolean matrix:

clock event | count erratum => clock source
------------+---------------+--------------
     0      |       0       |      1 (OK)
     0      |       1       |      0 (bug!) -> no interference, could use
     1      |       0       |      1 (OK)
     1      |       1       |      1 (bug!) -> can't use, interference

What we want instead is to enable the R4k clock source if there is no CP0
Count register read erratum (obviously) or the R4k clock event
initialization has *failed* -- because in the latter case we won't be
using the timer interrupt anyway, so we don't care about any interference
CP0 Count reads might cause with the interrupt.  This corresponds to the
following boolean matrix:

clock event | count erratum => clock source
------------+---------------+--------------
     0      |       0       |      1
     0      |       1       |      1
     1      |       0       |      1
     1      |       1       |      0

This is implemented here, effectively reverting the problematic commit,
and a short explanation is given next to code modified so that the
rationale is known to future readers and confusion is prevented from
happening here again.

It is worth noting that mips_clockevent_init returns 0 upon success while
cpu_has_mfc0_count_bug returns 0 upon failure.  This is because the former
function returns an error code while the latter returns a boolean value.
To signify the difference I have therefore chosen to compare the result of
the former call explicitly against 0.

Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5799/