blob: f3db185a68090c50fc20f934e84913a2b8c22ce4 [file] [log] [blame]
/dts-v1/;
#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
model = "Qualcomm APQ8064";
compatible = "qcom,apq8064";
interrupt-parent = <&intc>;
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
smem_region: smem@80000000 {
reg = <0x80000000 0x200000>;
no-map;
};
wcnss_mem: wcnss@8f000000 {
reg = <0x8f000000 0x700000>;
no-map;
};
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
CPU0: cpu@0 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <0>;
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
cpu-idle-states = <&CPU_SPC>;
};
CPU1: cpu@1 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <1>;
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
cpu-idle-states = <&CPU_SPC>;
};
CPU2: cpu@2 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <2>;
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
cpu-idle-states = <&CPU_SPC>;
};
CPU3: cpu@3 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <3>;
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
cpu-idle-states = <&CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
};
idle-states {
CPU_SPC: spc {
compatible = "qcom,idle-state-spc",
"arm,idle-state";
entry-latency-us = <400>;
exit-latency-us = <900>;
min-residency-us = <3000>;
};
};
};
thermal-zones {
cpu-thermal0 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 7>;
coefficients = <1199 0>;
trips {
cpu_alert0: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit0: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal1 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 8>;
coefficients = <1132 0>;
trips {
cpu_alert1: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit1: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal2 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 9>;
coefficients = <1199 0>;
trips {
cpu_alert2: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit2: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cpu-thermal3 {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&gcc 10>;
coefficients = <1132 0>;
trips {
cpu_alert3: trip0 {
temperature = <75000>;
hysteresis = <2000>;
type = "passive";
};
cpu_crit3: trip1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
};
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 10 0x304>;
};
clocks {
cxo_board: cxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
pxo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <27000000>;
};
sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
sfpb_mutex: hwmutex {
compatible = "qcom,sfpb-mutex";
syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
#hwlock-cells = <1>;
};
smem {
compatible = "qcom,smem";
memory-region = <&smem_region>;
hwlocks = <&sfpb_mutex 3>;
};
smd {
compatible = "qcom,smd";
modem@0 {
interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 3>;
qcom,smd-edge = <0>;
status = "disabled";
};
q6@1 {
interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 15>;
qcom,smd-edge = <1>;
status = "disabled";
};
dsps@3 {
interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
qcom,smd-edge = <3>;
status = "disabled";
};
riva@6 {
interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 25>;
qcom,smd-edge = <6>;
status = "disabled";
};
};
smsm {
compatible = "qcom,smsm";
#address-cells = <1>;
#size-cells = <0>;
qcom,ipc-1 = <&l2cc 8 4>;
qcom,ipc-2 = <&l2cc 8 14>;
qcom,ipc-3 = <&l2cc 8 23>;
qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>;
apps_smsm: apps@0 {
reg = <0>;
#qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
reg = <1>;
interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
q6_smsm: q6@2 {
reg = <2>;
interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
wcnss_smsm: wcnss@3 {
reg = <3>;
interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
dsps_smsm: dsps@4 {
reg = <4>;
interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
firmware {
scm {
compatible = "qcom,scm-apq8064";
clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
clock-names = "core";
};
};
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "simple-bus";
tlmm_pinmux: pinctrl@800000 {
compatible = "qcom,apq8064-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&ps_hold>;
};
sfpb_wrapper_mutex: syscon@1200000 {
compatible = "syscon";
reg = <0x01200000 0x8000>;
};
intc: interrupt-controller@2000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x02000000 0x1000>,
<0x02002000 0x1000>;
};
timer@200a000 {
compatible = "qcom,kpss-timer",
"qcom,kpss-wdt-apq8064", "qcom,msm-timer";
interrupts = <1 1 0x301>,
<1 2 0x301>,
<1 3 0x301>;
reg = <0x0200a000 0x100>;
clock-frequency = <27000000>,
<32768>;
cpu-offset = <0x80000>;
};
acc0: clock-controller@2088000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
};
acc1: clock-controller@2098000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
};
acc2: clock-controller@20a8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
};
acc3: clock-controller@20b8000 {
compatible = "qcom,kpss-acc-v1";
reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
};
saw0: power-controller@2089000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw1: power-controller@2099000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw2: power-controller@20a9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw3: power-controller@20b9000 {
compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
sps_sic_non_secure: sps-sic-non-secure@12100000 {
compatible = "syscon";
reg = <0x12100000 0x10000>;
};
gsbi1: gsbi@12440000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <1>;
reg = <0x12440000 0x100>;
clocks = <&gcc GSBI1_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi1_serial: serial@12450000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x12450000 0x100>,
<0x12400000 0x03>;
interrupts = <0 193 0x0>;
clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi1_i2c: i2c@12460000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c1_pins>;
pinctrl-1 = <&i2c1_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x12460000 0x1000>;
interrupts = <0 194 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi2: gsbi@12480000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
reg = <0x12480000 0x100>;
clocks = <&gcc GSBI2_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi2_i2c: i2c@124a0000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x124a0000 0x1000>;
pinctrl-0 = <&i2c2_pins>;
pinctrl-1 = <&i2c2_pins_sleep>;
pinctrl-names = "default", "sleep";
interrupts = <0 196 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi3: gsbi@16200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <3>;
reg = <0x16200000 0x100>;
clocks = <&gcc GSBI3_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi3_i2c: i2c@16280000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c3_pins>;
pinctrl-1 = <&i2c3_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16280000 0x1000>;
interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI3_QUP_CLK>,
<&gcc GSBI3_H_CLK>;
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi4: gsbi@16300000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <4>;
reg = <0x16300000 0x03>;
clocks = <&gcc GSBI4_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi4_i2c: i2c@16380000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c4_pins>;
pinctrl-1 = <&i2c4_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16380000 0x1000>;
interrupts = <GIC_SPI 153 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI4_QUP_CLK>,
<&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
};
};
gsbi5: gsbi@1a200000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <5>;
reg = <0x1a200000 0x03>;
clocks = <&gcc GSBI5_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi5_serial: serial@1a240000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x100>,
<0x1a200000 0x03>;
interrupts = <0 154 0x0>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi5_spi: spi@1a280000 {
compatible = "qcom,spi-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
interrupts = <0 155 0>;
pinctrl-0 = <&spi5_default>;
pinctrl-1 = <&spi5_sleep>;
pinctrl-names = "default", "sleep";
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
};
gsbi6: gsbi@16500000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <6>;
reg = <0x16500000 0x03>;
clocks = <&gcc GSBI6_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gsbi6_serial: serial@16540000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16540000 0x100>,
<0x16500000 0x03>;
interrupts = <0 156 0x0>;
clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi6_i2c: i2c@16580000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c6_pins>;
pinctrl-1 = <&i2c6_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16580000 0x1000>;
interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI6_QUP_CLK>,
<&gcc GSBI6_H_CLK>;
clock-names = "core", "iface";
};
};
gsbi7: gsbi@16600000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
cell-index = <7>;
reg = <0x16600000 0x100>;
clocks = <&gcc GSBI7_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon-tcsr = <&tcsr>;
gsbi7_serial: serial@16640000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16640000 0x1000>,
<0x16600000 0x1000>;
interrupts = <0 158 0x0>;
clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
gsbi7_i2c: i2c@16680000 {
compatible = "qcom,i2c-qup-v1.1.1";
pinctrl-0 = <&i2c7_pins>;
pinctrl-1 = <&i2c7_pins_sleep>;
pinctrl-names = "default", "sleep";
reg = <0x16680000 0x1000>;
interrupts = <GIC_SPI 159 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI7_QUP_CLK>,
<&gcc GSBI7_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
};
rng@1a500000 {
compatible = "qcom,prng";
reg = <0x1a500000 0x200>;
clocks = <&gcc PRNG_CLK>;
clock-names = "core";
};
ssbi@c00000 {
compatible = "qcom,ssbi";
reg = <0x00c00000 0x1000>;
qcom,controller-type = "pmic-arbiter";
pm8821: pmic@1 {
compatible = "qcom,pm8821";
interrupt-parent = <&tlmm_pinmux>;
interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
#interrupt-cells = <2>;
interrupt-controller;
#address-cells = <1>;
#size-cells = <0>;
pm8821_mpps: mpps@50 {
compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
reg = <0x50>;
interrupts = <24 IRQ_TYPE_NONE>,
<25 IRQ_TYPE_NONE>,
<26 IRQ_TYPE_NONE>,
<27 IRQ_TYPE_NONE>;
gpio-controller;
#gpio-cells = <2>;
};
};
};
qcom,ssbi@500000 {
compatible = "qcom,ssbi";
reg = <0x00500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
pmicintc: pmic@0 {
compatible = "qcom,pm8921";
interrupt-parent = <&tlmm_pinmux>;
interrupts = <74 8>;
#interrupt-cells = <2>;
interrupt-controller;
#address-cells = <1>;
#size-cells = <0>;
pm8921_gpio: gpio@150 {
compatible = "qcom,pm8921-gpio",
"qcom,ssbi-gpio";
reg = <0x150>;
interrupts = <192 IRQ_TYPE_NONE>,
<193 IRQ_TYPE_NONE>,
<194 IRQ_TYPE_NONE>,
<195 IRQ_TYPE_NONE>,
<196 IRQ_TYPE_NONE>,
<197 IRQ_TYPE_NONE>,
<198 IRQ_TYPE_NONE>,
<199 IRQ_TYPE_NONE>,
<200 IRQ_TYPE_NONE>,
<201 IRQ_TYPE_NONE>,
<202 IRQ_TYPE_NONE>,
<203 IRQ_TYPE_NONE>,
<204 IRQ_TYPE_NONE>,
<205 IRQ_TYPE_NONE>,
<206 IRQ_TYPE_NONE>,
<207 IRQ_TYPE_NONE>,
<208 IRQ_TYPE_NONE>,
<209 IRQ_TYPE_NONE>,
<210 IRQ_TYPE_NONE>,
<211 IRQ_TYPE_NONE>,
<212 IRQ_TYPE_NONE>,
<213 IRQ_TYPE_NONE>,
<214 IRQ_TYPE_NONE>,
<215 IRQ_TYPE_NONE>,
<216 IRQ_TYPE_NONE>,
<217 IRQ_TYPE_NONE>,
<218 IRQ_TYPE_NONE>,
<219 IRQ_TYPE_NONE>,
<220 IRQ_TYPE_NONE>,
<221 IRQ_TYPE_NONE>,
<222 IRQ_TYPE_NONE>,
<223 IRQ_TYPE_NONE>,
<224 IRQ_TYPE_NONE>,
<225 IRQ_TYPE_NONE>,
<226 IRQ_TYPE_NONE>,
<227 IRQ_TYPE_NONE>,
<228 IRQ_TYPE_NONE>,
<229 IRQ_TYPE_NONE>,
<230 IRQ_TYPE_NONE>,
<231 IRQ_TYPE_NONE>,
<232 IRQ_TYPE_NONE>,
<233 IRQ_TYPE_NONE>,
<234 IRQ_TYPE_NONE>,
<235 IRQ_TYPE_NONE>;
gpio-controller;
#gpio-cells = <2>;
};
pm8921_mpps: mpps@50 {
compatible = "qcom,pm8921-mpp",
"qcom,ssbi-mpp";
reg = <0x50>;
gpio-controller;
#gpio-cells = <2>;
interrupts =
<128 IRQ_TYPE_NONE>,
<129 IRQ_TYPE_NONE>,
<130 IRQ_TYPE_NONE>,
<131 IRQ_TYPE_NONE>,
<132 IRQ_TYPE_NONE>,
<133 IRQ_TYPE_NONE>,
<134 IRQ_TYPE_NONE>,
<135 IRQ_TYPE_NONE>,
<136 IRQ_TYPE_NONE>,
<137 IRQ_TYPE_NONE>,
<138 IRQ_TYPE_NONE>,
<139 IRQ_TYPE_NONE>;
};
rtc@11d {
compatible = "qcom,pm8921-rtc";
interrupt-parent = <&pmicintc>;
interrupts = <39 1>;
reg = <0x11d>;
allow-set-time;
};
pwrkey@1c {
compatible = "qcom,pm8921-pwrkey";
reg = <0x1c>;
interrupt-parent = <&pmicintc>;
interrupts = <50 1>, <51 1>;
debounce = <15625>;
pull-up;
};
};
};
qfprom: qfprom@700000 {
compatible = "qcom,qfprom";
reg = <0x00700000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
tsens_calib: calib {
reg = <0x404 0x10>;
};
tsens_backup: backup_calib {
reg = <0x414 0x10>;
};
};
gcc: clock-controller@900000 {
compatible = "qcom,gcc-apq8064";
reg = <0x00900000 0x4000>;
nvmem-cells = <&tsens_calib>, <&tsens_backup>;
nvmem-cell-names = "calib", "calib_backup";
#clock-cells = <1>;
#reset-cells = <1>;
#thermal-sensor-cells = <1>;
};
lcc: clock-controller@28000000 {
compatible = "qcom,lcc-apq8064";
reg = <0x28000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
mmcc: clock-controller@4000000 {
compatible = "qcom,mmcc-apq8064";
reg = <0x4000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
l2cc: clock-controller@2011000 {
compatible = "syscon";
reg = <0x2011000 0x1000>;
};
rpm@108000 {
compatible = "qcom,rpm-apq8064";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "ack", "err", "wakeup";
rpmcc: clock-controller {
compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
#clock-cells = <1>;
};
regulators {
compatible = "qcom,rpm-pm8921-regulators";
pm8921_s1: s1 {};
pm8921_s2: s2 {};
pm8921_s3: s3 {};
pm8921_s4: s4 {};
pm8921_s7: s7 {};
pm8921_s8: s8 {};
pm8921_l1: l1 {};
pm8921_l2: l2 {};
pm8921_l3: l3 {};
pm8921_l4: l4 {};
pm8921_l5: l5 {};
pm8921_l6: l6 {};
pm8921_l7: l7 {};
pm8921_l8: l8 {};
pm8921_l9: l9 {};
pm8921_l10: l10 {};
pm8921_l11: l11 {};
pm8921_l12: l12 {};
pm8921_l14: l14 {};
pm8921_l15: l15 {};
pm8921_l16: l16 {};
pm8921_l17: l17 {};
pm8921_l18: l18 {};
pm8921_l21: l21 {};
pm8921_l22: l22 {};
pm8921_l23: l23 {};
pm8921_l24: l24 {};
pm8921_l25: l25 {};
pm8921_l26: l26 {};
pm8921_l27: l27 {};
pm8921_l28: l28 {};
pm8921_l29: l29 {};
pm8921_lvs1: lvs1 {};
pm8921_lvs2: lvs2 {};
pm8921_lvs3: lvs3 {};
pm8921_lvs4: lvs4 {};
pm8921_lvs5: lvs5 {};
pm8921_lvs6: lvs6 {};
pm8921_lvs7: lvs7 {};
pm8921_usb_switch: usb-switch {};
pm8921_hdmi_switch: hdmi-switch {
bias-pull-down;
};
pm8921_ncp: ncp {};
};
};
usb1: usb@12500000 {
compatible = "qcom,ci-hdrc";
reg = <0x12500000 0x200>,
<0x12500200 0x200>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS1_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs1_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs1_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
#phy-cells = <0>;
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb1 0>;
reset-names = "por";
};
};
};
usb3: usb@12520000 {
compatible = "qcom,ci-hdrc";
reg = <0x12520000 0x200>,
<0x12520200 0x200>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS3_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs3_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs3_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
#phy-cells = <0>;
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb3 0>;
reset-names = "por";
};
};
};
usb4: usb@12530000 {
compatible = "qcom,ci-hdrc";
reg = <0x12530000 0x200>,
<0x12530200 0x200>;
interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
clock-names = "core", "iface";
assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
assigned-clock-rates = <60000000>;
resets = <&gcc USB_HS4_RESET>;
reset-names = "core";
phy_type = "ulpi";
ahb-burst-config = <0>;
phys = <&usb_hs4_phy>;
phy-names = "usb-phy";
status = "disabled";
#reset-cells = <1>;
ulpi {
usb_hs4_phy: phy {
compatible = "qcom,usb-hs-phy-apq8064",
"qcom,usb-hs-phy";
#phy-cells = <0>;
clocks = <&sleep_clk>, <&cxo_board>;
clock-names = "sleep", "ref";
resets = <&usb4 0>;
reset-names = "por";
};
};
};
sata_phy0: phy@1b400000 {
compatible = "qcom,apq8064-sata-phy";
status = "disabled";
reg = <0x1b400000 0x200>;
reg-names = "phy_mem";
clocks = <&gcc SATA_PHY_CFG_CLK>;
clock-names = "cfg";
#phy-cells = <0>;
};
sata0: sata@29000000 {
compatible = "qcom,apq8064-ahci", "generic-ahci";
status = "disabled";
reg = <0x29000000 0x180>;
interrupts = <GIC_SPI 209 IRQ_TYPE_NONE>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
<&gcc SATA_A_CLK>,
<&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
clock-names = "slave_iface",
"iface",
"bus",
"rxoob",
"core_pmalive";
assigned-clocks = <&gcc SATA_RXOOB_CLK>,
<&gcc SATA_PMALIVE_CLK>;
assigned-clock-rates = <100000000>, <100000000>;
phys = <&sata_phy0>;
phy-names = "sata-phy";
ports-implemented = <0x1>;
};
/* Temporary fixed regulator */
sdcc1bam:dma@12402000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
interrupts = <0 98 0>;
clocks = <&gcc SDC1_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc3bam:dma@12182000{
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
interrupts = <0 96 0>;
clocks = <&gcc SDC3_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
sdcc4bam:dma@121c2000{
compatible = "qcom,bam-v1.3.0";
reg = <0x121c2000 0x8000>;
interrupts = <0 95 0>;
clocks = <&gcc SDC4_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
amba {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
pinctrl-names = "default";
pinctrl-0 = <&sdcc1_pins>;
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <8>;
max-frequency = <96000000>;
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
dma-names = "tx", "rx";
};
sdcc3: sdcc@12180000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x12180000 0x2000>;
interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <192000000>;
no-1-8-v;
dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
dma-names = "tx", "rx";
};
sdcc4: sdcc@121c0000 {
compatible = "arm,pl18x", "arm,primecell";
arm,primecell-periphid = <0x00051180>;
status = "disabled";
reg = <0x121c0000 0x2000>;
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cmd_irq";
clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
clock-names = "mclk", "apb_pclk";
bus-width = <4>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <48000000>;
dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&sdc4_gpios>;
};
};
tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-apq8064", "syscon";
reg = <0x1a400000 0x100>;
};
gpu: adreno-3xx@4300000 {
compatible = "qcom,adreno-3xx";
reg = <0x04300000 0x20000>;
reg-names = "kgsl_3d0_reg_memory";
interrupts = <GIC_SPI 80 0>;
interrupt-names = "kgsl_3d0_irq";
clock-names =
"core_clk",
"iface_clk",
"mem_clk",
"mem_iface_clk";
clocks =
<&mmcc GFX3D_CLK>,
<&mmcc GFX3D_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>,
<&mmcc MMSS_IMEM_AHB_CLK>;
qcom,chipid = <0x03020002>;
iommus = <&gfx3d 0
&gfx3d 1
&gfx3d 2
&gfx3d 3
&gfx3d 4
&gfx3d 5
&gfx3d 6
&gfx3d 7
&gfx3d 8
&gfx3d 9
&gfx3d 10
&gfx3d 11
&gfx3d 12
&gfx3d 13
&gfx3d 14
&gfx3d 15
&gfx3d 16
&gfx3d 17
&gfx3d 18
&gfx3d 19
&gfx3d 20
&gfx3d 21
&gfx3d 22
&gfx3d 23
&gfx3d 24
&gfx3d 25
&gfx3d 26
&gfx3d 27
&gfx3d 28
&gfx3d 29
&gfx3d 30
&gfx3d 31
&gfx3d1 0
&gfx3d1 1
&gfx3d1 2
&gfx3d1 3
&gfx3d1 4
&gfx3d1 5
&gfx3d1 6
&gfx3d1 7
&gfx3d1 8
&gfx3d1 9
&gfx3d1 10
&gfx3d1 11
&gfx3d1 12
&gfx3d1 13
&gfx3d1 14
&gfx3d1 15
&gfx3d1 16
&gfx3d1 17
&gfx3d1 18
&gfx3d1 19
&gfx3d1 20
&gfx3d1 21
&gfx3d1 22
&gfx3d1 23
&gfx3d1 24
&gfx3d1 25
&gfx3d1 26
&gfx3d1 27
&gfx3d1 28
&gfx3d1 29
&gfx3d1 30
&gfx3d1 31>;
qcom,gpu-pwrlevels {
compatible = "qcom,gpu-pwrlevels";
qcom,gpu-pwrlevel@0 {
qcom,gpu-freq = <450000000>;
};
qcom,gpu-pwrlevel@1 {
qcom,gpu-freq = <27000000>;
};
};
};
mmss_sfpb: syscon@5700000 {
compatible = "syscon";
reg = <0x5700000 0x70>;
};
dsi0: mdss_dsi@4700000 {
compatible = "qcom,mdss-dsi-ctrl";
label = "MDSS DSI CTRL->0";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <GIC_SPI 82 0>;
reg = <0x04700000 0x200>;
reg-names = "dsi_ctrl";
clocks = <&mmcc DSI_M_AHB_CLK>,
<&mmcc DSI_S_AHB_CLK>,
<&mmcc AMP_AHB_CLK>,
<&mmcc DSI_CLK>,
<&mmcc DSI1_BYTE_CLK>,
<&mmcc DSI_PIXEL_CLK>,
<&mmcc DSI1_ESC_CLK>;
clock-names = "iface_clk", "bus_clk", "core_mmss_clk",
"src_clk", "byte_clk", "pixel_clk",
"core_clk";
assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
<&mmcc DSI1_ESC_SRC>,
<&mmcc DSI_SRC>,
<&mmcc DSI_PIXEL_SRC>;
assigned-clock-parents = <&dsi0_phy 0>,
<&dsi0_phy 0>,
<&dsi0_phy 1>,
<&dsi0_phy 1>;
syscon-sfpb = <&mmss_sfpb>;
phys = <&dsi0_phy>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dsi0_in: endpoint {
};
};
port@1 {
reg = <1>;
dsi0_out: endpoint {
};
};
};
};
dsi0_phy: dsi-phy@4700200 {
compatible = "qcom,dsi-phy-28nm-8960";
#clock-cells = <1>;
reg = <0x04700200 0x100>,
<0x04700300 0x200>,
<0x04700500 0x5c>;
reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
clock-names = "iface_clk";
clocks = <&mmcc DSI_M_AHB_CLK>;
};
mdp_port0: iommu@7500000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc MDP_AXI_CLK>;
reg = <0x07500000 0x100000>;
interrupts =
<GIC_SPI 63 0>,
<GIC_SPI 64 0>;
qcom,ncb = <2>;
};
mdp_port1: iommu@7600000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc MDP_AXI_CLK>;
reg = <0x07600000 0x100000>;
interrupts =
<GIC_SPI 61 0>,
<GIC_SPI 62 0>;
qcom,ncb = <2>;
};
gfx3d: iommu@7c00000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>;
reg = <0x07c00000 0x100000>;
interrupts =
<GIC_SPI 69 0>,
<GIC_SPI 70 0>;
qcom,ncb = <3>;
};
gfx3d1: iommu@7d00000 {
compatible = "qcom,apq8064-iommu";
#iommu-cells = <1>;
clock-names =
"smmu_pclk",
"iommu_clk";
clocks =
<&mmcc SMMU_AHB_CLK>,
<&mmcc GFX3D_AXI_CLK>;
reg = <0x07d00000 0x100000>;
interrupts =
<GIC_SPI 210 0>,
<GIC_SPI 211 0>;
qcom,ncb = <3>;
};
pcie: pci@1b500000 {
compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */
0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_REF_CLK>;
clock-names = "core", "iface", "phy";
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy";
status = "disabled";
};
hdmi: hdmi-tx@4a00000 {
compatible = "qcom,hdmi-tx-8960";
pinctrl-names = "default";
pinctrl-0 = <&hdmi_pinctrl>;
reg = <0x04a00000 0x2f0>;
reg-names = "core_physical";
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mmcc HDMI_APP_CLK>,
<&mmcc HDMI_M_AHB_CLK>,
<&mmcc HDMI_S_AHB_CLK>;
clock-names = "core_clk",
"master_iface_clk",
"slave_iface_clk";
phys = <&hdmi_phy>;
phy-names = "hdmi-phy";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
hdmi_in: endpoint {
};
};
port@1 {
reg = <1>;
hdmi_out: endpoint {
};
};
};
};
hdmi_phy: hdmi-phy@4a00400 {
compatible = "qcom,hdmi-phy-8960";
reg = <0x4a00400 0x60>,
<0x4a00500 0x100>;
reg-names = "hdmi_phy",
"hdmi_pll";
clocks = <&mmcc HDMI_S_AHB_CLK>;
clock-names = "slave_iface_clk";
};
mdp: mdp@5100000 {
compatible = "qcom,mdp4";
reg = <0x05100000 0xf0000>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mmcc MDP_CLK>,
<&mmcc MDP_AHB_CLK>,
<&mmcc MDP_AXI_CLK>,
<&mmcc MDP_LUT_CLK>,
<&mmcc HDMI_TV_CLK>,
<&mmcc MDP_TV_CLK>;
clock-names = "core_clk",
"iface_clk",
"bus_clk",
"lut_clk",
"hdmi_clk",
"tv_clk";
iommus = <&mdp_port0 0
&mdp_port0 2
&mdp_port1 0
&mdp_port1 2>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
mdp_lvds_out: endpoint {
};
};
port@1 {
reg = <1>;
mdp_dsi1_out: endpoint {
};
};
port@2 {
reg = <2>;
mdp_dsi2_out: endpoint {
};
};
port@3 {
reg = <3>;
mdp_dtv_out: endpoint {
};
};
};
};
riva: riva-pil@3204000 {
compatible = "qcom,riva-pil";
reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
reg-names = "ccu", "dxe", "pmu";
interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>,
<&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal";
memory-region = <&wcnss_mem>;
vddcx-supply = <&pm8921_s3>;
vddmx-supply = <&pm8921_l24>;
vddpx-supply = <&pm8921_s4>;
status = "disabled";
iris {
compatible = "qcom,wcn3660";
clocks = <&cxo_board>;
clock-names = "xo";
vddxo-supply = <&pm8921_l4>;
vddrfa-supply = <&pm8921_s2>;
vddpa-supply = <&pm8921_l10>;
vdddig-supply = <&pm8921_lvs2>;
};
smd-edge {
interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>;
qcom,ipc = <&l2cc 8 25>;
qcom,smd-edge = <6>;
label = "riva";
wcnss {
compatible = "qcom,wcnss";
qcom,smd-channels = "WCNSS_CTRL";
qcom,mmio = <&riva>;
bt {
compatible = "qcom,wcnss-bt";
};
wifi {
compatible = "qcom,wcnss-wlan";
interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "tx", "rx";
qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
qcom,smem-state-names = "tx-enable", "tx-rings-empty";
};
};
};
};
etb@1a01000 {
compatible = "coresight-etb10", "arm,primecell";
reg = <0x1a01000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
port {
etb_in: endpoint {
slave-mode;
remote-endpoint = <&replicator_out0>;
};
};
};
tpiu@1a03000 {
compatible = "arm,coresight-tpiu", "arm,primecell";
reg = <0x1a03000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
port {
tpiu_in: endpoint {
slave-mode;
remote-endpoint = <&replicator_out1>;
};
};
};
replicator {
compatible = "arm,coresight-replicator";
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
replicator_out0: endpoint {
remote-endpoint = <&etb_in>;
};
};
port@1 {
reg = <1>;
replicator_out1: endpoint {
remote-endpoint = <&tpiu_in>;
};
};
port@2 {
reg = <0>;
replicator_in: endpoint {
slave-mode;
remote-endpoint = <&funnel_out>;
};
};
};
};
funnel@1a04000 {
compatible = "arm,coresight-funnel", "arm,primecell";
reg = <0x1a04000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
ports {
#address-cells = <1>;
#size-cells = <0>;
/*
* Not described input ports:
* 2 - connected to STM component
* 3 - not-connected
* 6 - not-connected
* 7 - not-connected
*/
port@0 {
reg = <0>;
funnel_in0: endpoint {
slave-mode;
remote-endpoint = <&etm0_out>;
};
};
port@1 {
reg = <1>;
funnel_in1: endpoint {
slave-mode;
remote-endpoint = <&etm1_out>;
};
};
port@4 {
reg = <4>;
funnel_in4: endpoint {
slave-mode;
remote-endpoint = <&etm2_out>;
};
};
port@5 {
reg = <5>;
funnel_in5: endpoint {
slave-mode;
remote-endpoint = <&etm3_out>;
};
};
port@8 {
reg = <0>;
funnel_out: endpoint {
remote-endpoint = <&replicator_in>;
};
};
};
};
etm@1a1c000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1c000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU0>;
port {
etm0_out: endpoint {
remote-endpoint = <&funnel_in0>;
};
};
};
etm@1a1d000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1d000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU1>;
port {
etm1_out: endpoint {
remote-endpoint = <&funnel_in1>;
};
};
};
etm@1a1e000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1e000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU2>;
port {
etm2_out: endpoint {
remote-endpoint = <&funnel_in4>;
};
};
};
etm@1a1f000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x1a1f000 0x1000>;
clocks = <&rpmcc RPM_QDSS_CLK>;
clock-names = "apb_pclk";
cpu = <&CPU3>;
port {
etm3_out: endpoint {
remote-endpoint = <&funnel_in5>;
};
};
};
};
};
#include "qcom-apq8064-pins.dtsi"