diff --git a/Documentation/arm/00-INDEX b/Documentation/arm/00-INDEX
index 8edb900..dea011c 100644
--- a/Documentation/arm/00-INDEX
+++ b/Documentation/arm/00-INDEX
@@ -10,8 +10,6 @@
 	- Intel IXP4xx Network processor.
 Makefile
 	- Build sourcefiles as part of the Documentation-build for arm
-msm/
-	- MSM specific documentation
 Netwinder
 	- Netwinder specific documentation
 Porting
diff --git a/Documentation/arm/msm/gpiomux.txt b/Documentation/arm/msm/gpiomux.txt
deleted file mode 100644
index 67a8162..0000000
--- a/Documentation/arm/msm/gpiomux.txt
+++ /dev/null
@@ -1,176 +0,0 @@
-This document provides an overview of the msm_gpiomux interface, which
-is used to provide gpio pin multiplexing and configuration on mach-msm
-targets.
-
-History
-=======
-
-The first-generation API for gpio configuration & multiplexing on msm
-is the function gpio_tlmm_config().  This function has a few notable
-shortcomings, which led to its deprecation and replacement by gpiomux:
-
-The 'disable' parameter:  Setting the second parameter to
-gpio_tlmm_config to GPIO_CFG_DISABLE tells the peripheral
-processor in charge of the subsystem to perform a look-up into a
-low-power table and apply the low-power/sleep setting for the pin.
-As the msm family evolved this became problematic. Not all pins
-have sleep settings, not all peripheral processors will accept requests
-to apply said sleep settings, and not all msm targets have their gpio
-subsystems managed by a peripheral processor. In order to get consistent
-behavior on all targets, drivers are forced to ignore this parameter,
-rendering it useless.
-
-The 'direction' flag: for all mux-settings other than raw-gpio (0),
-the output-enable bit of a gpio is hard-wired to a known
-input (usually VDD or ground).  For those settings, the direction flag
-is meaningless at best, and deceptive at worst.  In addition, using the
-direction flag to change output-enable (OE) directly can cause trouble in
-gpiolib, which has no visibility into gpio direction changes made
-in this way.  Direction control in gpio mode should be made through gpiolib.
-
-Key Features of gpiomux
-=======================
-
-- A consistent interface across all generations of msm.  Drivers can expect
-the same results on every target.
-- gpiomux plays nicely with gpiolib.  Functions that should belong to gpiolib
-are left to gpiolib and not duplicated here.  gpiomux is written with the
-intent that gpio_chips will call gpiomux reference-counting methods
-from their request() and free() hooks, providing full integration.
-- Tabular configuration.  Instead of having to call gpio_tlmm_config
-hundreds of times, gpio configuration is placed in a single table.
-- Per-gpio sleep.  Each gpio is individually reference counted, allowing only
-those lines which are in use to be put in high-power states.
-- 0 means 'do nothing': all flags are designed so that the default memset-zero
-equates to a sensible default of 'no configuration', preventing users
-from having to provide hundreds of 'no-op' configs for unused or
-unwanted lines.
-
-Usage
-=====
-
-To use gpiomux, provide configuration information for relevant gpio lines
-in the msm_gpiomux_configs table.  Since a 0 equates to "unconfigured",
-only those lines to be managed by gpiomux need to be specified.  Here
-is a completely fictional example:
-
-struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
-	[12] = {
-		.active = GPIOMUX_VALID | GPIOMUX_DRV_8MA | GPIOMUX_FUNC_1,
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-	[34] = {
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-};
-
-To indicate that a gpio is in use, call msm_gpiomux_get() to increase
-its reference count.  To decrease the reference count, call msm_gpiomux_put().
-
-The effect of this configuration is as follows:
-
-When the system boots, gpios 12 and 34 will be initialized with their
-'suspended' configurations.  All other gpios, which were left unconfigured,
-will not be touched.
-
-When msm_gpiomux_get() is called on gpio 12 to raise its reference count
-above 0, its active configuration will be applied.  Since no other gpio
-line has a valid active configuration, msm_gpiomux_get() will have no
-effect on any other line.
-
-When msm_gpiomux_put() is called on gpio 12 or 34 to drop their reference
-count to 0, their suspended configurations will be applied.
-Since no other gpio line has a valid suspended configuration, no other
-gpio line will be effected by msm_gpiomux_put().  Since gpio 34 has no valid
-active configuration, this is effectively a no-op for gpio 34 as well,
-with one small caveat, see the section "About Output-Enable Settings".
-
-All of the GPIOMUX_VALID flags may seem like unnecessary overhead, but
-they address some important issues.  As unused entries (all those
-except 12 and 34) are zero-filled, gpiomux needs a way to distinguish
-the used fields from the unused.  In addition, the all-zero pattern
-is a valid configuration!  Therefore, gpiomux defines an additional bit
-which is used to indicate when a field is used.  This has the pleasant
-side-effect of allowing calls to msm_gpiomux_write to use '0' to indicate
-that a value should not be changed:
-
-  msm_gpiomux_write(0, GPIOMUX_VALID, 0);
-
-replaces the active configuration of gpio 0 with an all-zero configuration,
-but leaves the suspended configuration as it was.
-
-Static Configurations
-=====================
-
-To install a static configuration, which is applied at boot and does
-not change after that, install a configuration with a suspended component
-but no active component, as in the previous example:
-
-	[34] = {
-		.suspended = GPIOMUX_VALID | GPIOMUX_PULL_DOWN,
-	},
-
-The suspended setting is applied during boot, and the lack of any valid
-active setting prevents any other setting from being applied at runtime.
-If other subsystems attempting to access the line is a concern, one could
-*really* anchor the configuration down by calling msm_gpiomux_get on the
-line at initialization to move the line into active mode.  With the line
-held, it will never be re-suspended, and with no valid active configuration,
-no new configurations will be applied.
-
-But then, if having other subsystems grabbing for the line is truly a concern,
-it should be reserved with gpio_request instead, which carries an implicit
-msm_gpiomux_get.
-
-gpiomux and gpiolib
-===================
-
-It is expected that msm gpio_chips will call msm_gpiomux_get() and
-msm_gpiomux_put() from their request and free hooks, like this fictional
-example:
-
-static int request(struct gpio_chip *chip, unsigned offset)
-{
-        return msm_gpiomux_get(chip->base + offset);
-}
-
-static void free(struct gpio_chip *chip, unsigned offset)
-{
-        msm_gpiomux_put(chip->base + offset);
-}
-
-	...somewhere in a gpio_chip declaration...
-	.request = request,
-	.free    = free,
-
-This provides important functionality:
-- It guarantees that a gpio line will have its 'active' config applied
-  when the line is requested, and will not be suspended while the line
-  remains requested; and
-- It guarantees that gpio-direction settings from gpiolib behave sensibly.
-  See "About Output-Enable Settings."
-
-This mechanism allows for "auto-request" of gpiomux lines via gpiolib
-when it is suitable.  Drivers wishing more exact control are, of course,
-free to also use msm_gpiomux_set and msm_gpiomux_get.
-
-About Output-Enable Settings
-============================
-
-Some msm targets do not have the ability to query the current gpio
-configuration setting.  This means that changes made to the output-enable
-(OE) bit by gpiolib cannot be consistently detected and preserved by gpiomux.
-Therefore, when gpiomux applies a configuration setting, any direction
-settings which may have been applied by gpiolib are lost and the default
-input settings are re-applied.
-
-For this reason, drivers should not assume that gpio direction settings
-continue to hold if they free and then re-request a gpio.  This seems like
-common sense - after all, anybody could have obtained the line in the
-meantime - but it needs saying.
-
-This also means that calls to msm_gpiomux_write will reset the OE bit,
-which means that if the gpio line is held by a client of gpiolib and
-msm_gpiomux_write is called, the direction setting has been lost and
-gpiolib's internal state has been broken.
-Release gpio lines before reconfiguring them.
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt
index a6391e7..90787aa 100644
--- a/Documentation/devicetree/bindings/serial/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt
@@ -1,9 +1,10 @@
 * Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
 
 Required properties:
-- compatible: Should be "atmel,<chip>-usart"
+- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu"
   The compatible <chip> indicated will be the first SoC to support an
   additional mode or an USART new feature.
+  For the dbgu UART, use "atmel,<chip>-dbgu", "atmel,<chip>-usart"
 - reg: Should contain registers location and length
 - interrupts: Should contain interrupt
 - clock-names: tuple listing input clock names.
diff --git a/MAINTAINERS b/MAINTAINERS
index 8e9ecbe..9988e1a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1261,22 +1261,6 @@
 W:	http://wiki.openmoko.org/wiki/Neo_FreeRunner
 S:	Supported
 
-ARM/QUALCOMM MSM MACHINE SUPPORT
-M:	David Brown <davidb@codeaurora.org>
-M:	Daniel Walker <dwalker@fifo99.com>
-M:	Bryan Huntsman <bryanh@codeaurora.org>
-L:	linux-arm-msm@vger.kernel.org
-F:	arch/arm/mach-msm/
-F:	drivers/video/fbdev/msm/
-F:	drivers/mmc/host/msm_sdcc.c
-F:	drivers/mmc/host/msm_sdcc.h
-F:	drivers/tty/serial/msm_serial.h
-F:	drivers/tty/serial/msm_serial.c
-F:	drivers/*/pm8???-*
-F:	drivers/mfd/ssbi.c
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git
-S:	Maintained
-
 ARM/TOSA MACHINE SUPPORT
 M:	Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
 M:	Dirk Opfer <dirk@opfer-online.de>
@@ -1334,6 +1318,10 @@
 S:	Maintained
 F:	arch/arm/mach-qcom/
 F:	drivers/soc/qcom/
+F:	drivers/tty/serial/msm_serial.h
+F:	drivers/tty/serial/msm_serial.c
+F:	drivers/*/pm8???-*
+F:	drivers/mfd/ssbi.c
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom.git
 
 ARM/RADISYS ENP2611 MACHINE SUPPORT
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 392e7ae..c8baa96 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -367,9 +367,9 @@
 	select ARCH_REQUIRE_GPIOLIB
 	select CLKDEV_LOOKUP
 	select IRQ_DOMAIN
-	select NEED_MACH_IO_H if PCCARD
 	select PINCTRL
 	select PINCTRL_AT91
+	select SOC_BUS
 	select USE_OF
 	help
 	  This enables support for systems based on Atmel
@@ -632,18 +632,6 @@
 	help
 	  Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
 
-config ARCH_MSM
-	bool "Qualcomm MSM (non-multiplatform)"
-	select ARCH_REQUIRE_GPIOLIB
-	select COMMON_CLK
-	select GENERIC_CLOCKEVENTS
-	help
-	  Support for Qualcomm MSM/QSD based systems.  This runs on the
-	  apps processor of the MSM/QSD and depends on a shared memory
-	  interface to the modem processor which runs the baseband
-	  stack and controls some vital subsystems
-	  (clock and power control, etc).
-
 config ARCH_SHMOBILE_LEGACY
 	bool "Renesas ARM SoCs (non-multiplatform)"
 	select ARCH_SHMOBILE
@@ -897,8 +885,6 @@
 
 source "arch/arm/mach-meson/Kconfig"
 
-source "arch/arm/mach-msm/Kconfig"
-
 source "arch/arm/mach-moxart/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 8b0183a..4cfb4b8 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -448,25 +448,6 @@
 		  Say Y here if you want kernel low-level debugging support
 		  on MMP UART3.
 
-	config DEBUG_MSM_UART
-		bool "Kernel low-level debugging messages via MSM UART"
-		depends on ARCH_MSM
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to the serial port on MSM devices.
-
-		  ARCH                DEBUG_UART_PHYS   DEBUG_UART_VIRT   #
-		  MSM7X00A, QSD8X50   0xa9a00000        0xe1000000        UART1
-		  MSM7X00A, QSD8X50   0xa9b00000        0xe1000000        UART2
-		  MSM7X00A, QSD8X50   0xa9c00000        0xe1000000        UART3
-
-		  MSM7X30             0xaca00000        0xe1000000        UART1
-		  MSM7X30             0xacb00000        0xe1000000        UART2
-		  MSM7X30             0xacc00000        0xe1000000        UART3
-
-		  Please adjust DEBUG_UART_PHYS and DEBUG_UART_BASE configuration
-		  options based on your needs.
-
 	config DEBUG_QCOM_UARTDM
 		bool "Kernel low-level debugging messages via QCOM UARTDM"
 		depends on ARCH_QCOM
@@ -806,7 +787,7 @@
 		  via SCIF2 on Renesas R-Car H1 (R8A7779).
 
 	config DEBUG_RCAR_GEN2_SCIF0
-		bool "Kernel low-level debugging messages via SCIF0 on R8A7790/R8A7791/R8A7793)"
+		bool "Kernel low-level debugging messages via SCIF0 on R8A7790/R8A7791/R8A7793"
 		depends on ARCH_R8A7790 || ARCH_R8A7791 || ARCH_R8A7793
 		help
 		  Say Y here if you want kernel low-level debugging support
@@ -1295,7 +1276,7 @@
 				 DEBUG_IMX6SL_UART || \
 				 DEBUG_IMX6SX_UART
 	default "debug/ks8695.S" if DEBUG_KS8695_UART
-	default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
+	default "debug/msm.S" if DEBUG_QCOM_UARTDM
 	default "debug/netx.S" if DEBUG_NETX_UART
 	default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
 	default "debug/renesas-scif.S" if DEBUG_R7S72100_SCIF2
@@ -1388,7 +1369,6 @@
 	default 0x80230000 if DEBUG_PICOXCELL_UART
 	default 0x808c0000 if ARCH_EP93XX
 	default 0x90020000 if DEBUG_NSPIRE_CLASSIC_UART || DEBUG_NSPIRE_CX_UART
-	default 0xa9a00000 if DEBUG_MSM_UART
 	default 0xb0060000 if DEBUG_SIRFPRIMA2_UART1
 	default 0xb0090000 if DEBUG_VEXPRESS_UART0_CRX
 	default 0xc0013000 if DEBUG_U300_UART
@@ -1433,7 +1413,7 @@
 	        DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
 		DEBUG_LL_UART_EFM32 || \
 		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
-		DEBUG_MSM_UART || DEBUG_NETX_UART || \
+		DEBUG_NETX_UART || \
 		DEBUG_QCOM_UARTDM || DEBUG_R7S72100_SCIF2 || \
 		DEBUG_RCAR_GEN1_SCIF0 || DEBUG_RCAR_GEN1_SCIF2 || \
 		DEBUG_RCAR_GEN2_SCIF0 || DEBUG_RCAR_GEN2_SCIF2 || \
@@ -1446,7 +1426,6 @@
 	hex "Virtual base address of debug UART"
 	default 0xe0000a00 if DEBUG_NETX_UART
 	default 0xe0010fe0 if ARCH_RPC
-	default 0xe1000000 if DEBUG_MSM_UART
 	default 0xf0000be0 if ARCH_EBSA110
 	default 0xf0010000 if DEBUG_ASM9260_UART
 	default 0xf01fb000 if DEBUG_NOMADIK_UART
@@ -1526,7 +1505,7 @@
 	default DEBUG_UART_PHYS if !MMU
 	depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
 		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
-		DEBUG_MSM_UART || DEBUG_NETX_UART || \
+		DEBUG_NETX_UART || \
 		DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
 		DEBUG_UART_BCM63XX || DEBUG_ASM9260_UART || \
 		DEBUG_SIRFSOC_UART || DEBUG_DIGICOLOR_UA0
@@ -1556,7 +1535,7 @@
 
 config DEBUG_UNCOMPRESS
 	bool
-	depends on ARCH_MULTIPLATFORM || ARCH_MSM || PLAT_SAMSUNG
+	depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG
 	default y if DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM)
 	help
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 5575d9f..cced41d 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -136,7 +136,6 @@
 ifeq ($(CONFIG_ARCH_SA1100),y)
 textofs-$(CONFIG_SA1111) := 0x00208000
 endif
-textofs-$(CONFIG_ARCH_MSM7X30) := 0x00208000
 textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
 textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
 textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
@@ -171,7 +170,6 @@
 machine-$(CONFIG_ARCH_MESON)		+= meson
 machine-$(CONFIG_ARCH_MMP)		+= mmp
 machine-$(CONFIG_ARCH_MOXART)		+= moxart
-machine-$(CONFIG_ARCH_MSM)		+= msm
 machine-$(CONFIG_ARCH_MV78XX0)		+= mv78xx0
 machine-$(CONFIG_ARCH_MVEBU)		+= mvebu
 machine-$(CONFIG_ARCH_MXC)		+= imx
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index 21c2b50..c515e4b 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -830,7 +830,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91rm9200-usart";
+				compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 62d25b1..d88fe62 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -753,7 +753,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index d55fdf2..bf8d185 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -276,7 +276,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index e4f61a9..111889b 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -762,7 +762,7 @@
 			};
 
 			dbgu: serial@ffffee00 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 8ec05b1..70e59c5 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -893,7 +893,7 @@
 			};
 
 			dbgu: serial@ffffee00 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 0c53a37..ea0af0f 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -757,7 +757,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 40f645b..ebfd5ce 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -377,7 +377,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index d221179..3aa56ae 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -860,7 +860,7 @@
 			};
 
 			dbgu: serial@fffff200 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 367af53..c0a8dfc 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -439,7 +439,7 @@
 			};
 
 			dbgu: serial@ffffee00 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>,
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index 4303874..782587d 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -1064,7 +1064,7 @@
 			};
 
 			dbgu: serial@fc069000 {
-				compatible = "atmel,at91sam9260-usart";
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfc069000 0x200>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index e6b0007..af07e05 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -24,9 +24,8 @@
 CONFIG_MACH_SCB9328=y
 CONFIG_MACH_APF9328=y
 CONFIG_MACH_MX21ADS=y
-CONFIG_MACH_MX25_3DS=y
 CONFIG_MACH_EUKREA_CPUIMX25SD=y
-CONFIG_MACH_IMX25_DT=y
+CONFIG_SOC_IMX25=y
 CONFIG_MACH_MX27ADS=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
diff --git a/arch/arm/configs/msm_defconfig b/arch/arm/configs/msm_defconfig
deleted file mode 100644
index dd18c9e..0000000
--- a/arch/arm/configs/msm_defconfig
+++ /dev/null
@@ -1,121 +0,0 @@
-CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS_ALL=y
-CONFIG_EMBEDDED=y
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_PROFILING=y
-CONFIG_OPROFILE=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_ARCH_MSM=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-CONFIG_HIGHMEM=y
-CONFIG_HIGHPTE=y
-CONFIG_CLEANCACHE=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_VFP=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_ADVANCED_ROUTER=y
-CONFIG_IP_MULTIPLE_TABLES=y
-CONFIG_IP_ROUTE_VERBOSE=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_CFG80211=y
-CONFIG_RFKILL=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_CHR_DEV_SG=y
-CONFIG_CHR_DEV_SCH=y
-CONFIG_SCSI_MULTI_LUN=y
-CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_LOGGING=y
-CONFIG_SCSI_SCAN_ASYNC=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-CONFIG_SLIP=y
-CONFIG_SLIP_COMPRESSED=y
-CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_USB_USBNET=y
-# CONFIG_USB_NET_AX8817X is not set
-# CONFIG_USB_NET_ZAURUS is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_MOUSE_PS2 is not set
-CONFIG_INPUT_JOYSTICK=y
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=y
-CONFIG_SERIO_LIBPS2=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_MSM=y
-CONFIG_SERIAL_MSM_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_SPI=y
-CONFIG_DEBUG_GPIO=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_THERMAL=y
-CONFIG_REGULATOR=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_FB=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_DYNAMIC_MINORS=y
-# CONFIG_SND_ARM is not set
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=y
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_MON=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_ACM=y
-CONFIG_USB_SERIAL=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_DEBUG_FILES=y
-CONFIG_USB_GADGET_VBUS_DRAW=500
-CONFIG_RTC_CLASS=y
-CONFIG_STAGING=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-CONFIG_EXT4_FS=y
-CONFIG_FUSE_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_CIFS=y
-CONFIG_PRINTK_TIME=y
-CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_LOCKUP_DETECTOR=y
-# CONFIG_DETECT_HUNG_TASK is not set
-# CONFIG_SCHED_DEBUG is not set
-CONFIG_TIMER_STATS=y
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index 9d56781..f69a459 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -13,7 +13,7 @@
 CONFIG_MACH_KIRKWOOD=y
 CONFIG_MACH_NETXBIG=y
 CONFIG_ARCH_MXC=y
-CONFIG_MACH_IMX25_DT=y
+CONFIG_SOC_IMX25=y
 CONFIG_MACH_IMX27_DT=y
 CONFIG_ARCH_U300=y
 CONFIG_PCI_MVEBU=y
diff --git a/arch/arm/include/debug/msm.S b/arch/arm/include/debug/msm.S
index e55a942..b03024f 100644
--- a/arch/arm/include/debug/msm.S
+++ b/arch/arm/include/debug/msm.S
@@ -16,24 +16,17 @@
  */
 
 	.macro	addruart, rp, rv, tmp
-#ifdef CONFIG_DEBUG_UART_PHYS
 	ldr	\rp, =CONFIG_DEBUG_UART_PHYS
 	ldr	\rv, =CONFIG_DEBUG_UART_VIRT
-#endif
 	.endm
 
 	.macro	senduart, rd, rx
 ARM_BE8(rev	\rd, \rd )
-#ifdef CONFIG_DEBUG_QCOM_UARTDM
 	@ Write the 1 character to UARTDM_TF
 	str	\rd, [\rx, #0x70]
-#else
-	str	\rd, [\rx, #0x0C]
-#endif
 	.endm
 
 	.macro	waituart, rd, rx
-#ifdef CONFIG_DEBUG_QCOM_UARTDM
 	@ check for TX_EMT in UARTDM_SR
 	ldr	\rd, [\rx, #0x08]
 ARM_BE8(rev     \rd, \rd )
@@ -55,13 +48,6 @@
 	str	\rd, [\rx, #0x40]
 	@ UARTDM reg. Read to induce delay
 	ldr	\rd, [\rx, #0x08]
-#else
-	@ wait for TX_READY
-1001:	ldr	\rd, [\rx, #0x08]
-ARM_BE8(rev     \rd, \rd )
-	tst	\rd, #0x04
-	beq	1001b
-#endif
 	.endm
 
 	.macro	busyuart, rd, rx
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index c74a443..4da6bae 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -24,7 +24,7 @@
 	select GENERIC_CLOCKEVENTS
 	select MEMORY
 	select ATMEL_SDRAMC
-	select PHYLIB if NETDEVICES
+	select SRAM if PM
 
 menu "Atmel AT91 System-on-Chip"
 
@@ -81,6 +81,8 @@
 	select CPU_ARM920T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_USB_CLK
+	select MIGHT_HAVE_PCI
+	select SRAM if PM
 
 config SOC_AT91SAM9
 	bool "AT91SAM9"
@@ -94,6 +96,7 @@
 	select HAVE_AT91_UTMI
 	select HAVE_FB_ATMEL
 	select MEMORY
+	select SRAM if PM
 	help
 	  Select this if you are using one of those Atmel SoC:
 	    AT91SAM9260
@@ -116,20 +119,6 @@
 
 comment "AT91 Feature Selections"
 
-config AT91_SLOW_CLOCK
-	bool "Suspend-to-RAM disables main oscillator"
-	select SRAM
-	depends on SUSPEND
-	help
-	  Select this if you want Suspend-to-RAM to save the most power
-	  possible (without powering off the CPU) by disabling the PLLs
-	  and main oscillator so that only the 32 KiHz clock is available.
-
-	  When only that slow-clock is available, some peripherals lose
-	  functionality.  Many can't issue wakeup events unless faster
-	  clocks are available.  Some lose their operating state and
-	  need to be completely re-initialized.
-
 config AT91_TIMER_HZ
        int "Kernel HZ (jiffies per second)"
        range 32 1024
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 827fdbc..ea54c98 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -2,7 +2,7 @@
 # Makefile for the linux kernel.
 #
 
-obj-y		:= setup.o
+obj-y		:= soc.o
 
 obj-$(CONFIG_SOC_AT91SAM9)	+= sam9_smc.o
 
@@ -13,7 +13,7 @@
 
 # Power Management
 obj-$(CONFIG_PM)		+= pm.o
-obj-$(CONFIG_AT91_SLOW_CLOCK)	+= pm_slowclock.o
+obj-$(CONFIG_PM)		+= pm_suspend.o
 
 ifeq ($(CONFIG_PM_DEBUG),y)
 CFLAGS_pm.o += -DDEBUG
diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c
index 8fcfb70..bfc9aed 100644
--- a/arch/arm/mach-at91/at91rm9200.c
+++ b/arch/arm/mach-at91/at91rm9200.c
@@ -8,25 +8,22 @@
  * Licensed under GPLv2 or later.
  */
 
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/gpio.h>
-#include <linux/of.h>
-#include <linux/of_irq.h>
-#include <linux/of_platform.h>
 #include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
 
-#include <asm/setup.h>
-#include <asm/irq.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
 #include <asm/system_misc.h>
 
 #include <mach/at91_st.h>
 
 #include "generic.h"
+#include "soc.h"
+
+static const struct at91_soc rm9200_socs[] = {
+	AT91_SOC(AT91RM9200_CIDR_MATCH, 0, "at91rm9200 BGA", "at91rm9200"),
+	{ /* sentinel */ },
+};
 
 static void at91rm9200_restart(enum reboot_mode reboot_mode, const char *cmd)
 {
@@ -45,15 +42,20 @@
 
 static void __init at91rm9200_dt_device_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+	struct soc_device *soc;
+	struct device *soc_dev = NULL;
+
+	soc = at91_soc_init(rm9200_socs);
+	if (soc != NULL)
+		soc_dev = soc_device_to_device(soc);
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev);
 
 	arm_pm_idle = at91rm9200_idle;
 	arm_pm_restart = at91rm9200_restart;
 	at91rm9200_pm_init();
 }
 
-
-
 static const char *at91rm9200_dt_board_compat[] __initconst = {
 	"atmel,at91rm9200",
 	NULL
@@ -61,7 +63,6 @@
 
 DT_MACHINE_START(at91rm9200_dt, "Atmel AT91RM9200")
 	.init_time      = at91rm9200_dt_timer_init,
-	.map_io		= at91_map_io,
 	.init_machine	= at91rm9200_dt_device_init,
 	.dt_compat	= at91rm9200_dt_board_compat,
 MACHINE_END
diff --git a/arch/arm/mach-at91/at91sam9.c b/arch/arm/mach-at91/at91sam9.c
index 56e3ba7..e47a209 100644
--- a/arch/arm/mach-at91/at91sam9.c
+++ b/arch/arm/mach-at91/at91sam9.c
@@ -7,29 +7,68 @@
  * Licensed under GPLv2 or later.
  */
 
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/gpio.h>
 #include <linux/of.h>
-#include <linux/of_irq.h>
 #include <linux/of_platform.h>
-#include <linux/clk-provider.h>
 
-#include <asm/system_misc.h>
-#include <asm/setup.h>
-#include <asm/irq.h>
 #include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
+#include <asm/system_misc.h>
 
 #include "generic.h"
+#include "soc.h"
+
+static const struct at91_soc at91sam9_socs[] = {
+	AT91_SOC(AT91SAM9260_CIDR_MATCH, 0, "at91sam9260", NULL),
+	AT91_SOC(AT91SAM9261_CIDR_MATCH, 0, "at91sam9261", NULL),
+	AT91_SOC(AT91SAM9263_CIDR_MATCH, 0, "at91sam9263", NULL),
+	AT91_SOC(AT91SAM9G20_CIDR_MATCH, 0, "at91sam9g20", NULL),
+	AT91_SOC(AT91SAM9RL64_CIDR_MATCH, 0, "at91sam9rl64", NULL),
+	AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9M11_EXID_MATCH,
+		 "at91sam9m11", "at91sam9g45"),
+	AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9M10_EXID_MATCH,
+		 "at91sam9m10", "at91sam9g45"),
+	AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9G46_EXID_MATCH,
+		 "at91sam9g46", "at91sam9g45"),
+	AT91_SOC(AT91SAM9G45_CIDR_MATCH, AT91SAM9G45_EXID_MATCH,
+		 "at91sam9g45", "at91sam9g45"),
+	AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G15_EXID_MATCH,
+		 "at91sam9g15", "at91sam9x5"),
+	AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G35_EXID_MATCH,
+		 "at91sam9g35", "at91sam9x5"),
+	AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9X35_EXID_MATCH,
+		 "at91sam9x35", "at91sam9x5"),
+	AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9G25_EXID_MATCH,
+		 "at91sam9g25", "at91sam9x5"),
+	AT91_SOC(AT91SAM9X5_CIDR_MATCH, AT91SAM9X25_EXID_MATCH,
+		 "at91sam9x25", "at91sam9x5"),
+	AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9CN12_EXID_MATCH,
+		 "at91sam9cn12", "at91sam9n12"),
+	AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9N12_EXID_MATCH,
+		 "at91sam9n12", "at91sam9n12"),
+	AT91_SOC(AT91SAM9N12_CIDR_MATCH, AT91SAM9CN11_EXID_MATCH,
+		 "at91sam9cn11", "at91sam9n12"),
+	AT91_SOC(AT91SAM9XE128_CIDR_MATCH, 0, "at91sam9xe128", "at91sam9xe128"),
+	AT91_SOC(AT91SAM9XE256_CIDR_MATCH, 0, "at91sam9xe256", "at91sam9xe256"),
+	AT91_SOC(AT91SAM9XE512_CIDR_MATCH, 0, "at91sam9xe512", "at91sam9xe512"),
+	{ /* sentinel */ },
+};
+
+static void __init at91sam9_common_init(void)
+{
+	struct soc_device *soc;
+	struct device *soc_dev = NULL;
+
+	soc = at91_soc_init(at91sam9_socs);
+	if (soc != NULL)
+		soc_dev = soc_device_to_device(soc);
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev);
+
+	arm_pm_idle = at91sam9_idle;
+}
 
 static void __init at91sam9_dt_device_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-
-	arm_pm_idle = at91sam9_idle;
+	at91sam9_common_init();
 	at91sam9260_pm_init();
 }
 
@@ -40,16 +79,13 @@
 
 DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM9")
 	/* Maintainer: Atmel */
-	.map_io		= at91_map_io,
 	.init_machine	= at91sam9_dt_device_init,
 	.dt_compat	= at91_dt_board_compat,
 MACHINE_END
 
 static void __init at91sam9g45_dt_device_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-
-	arm_pm_idle = at91sam9_idle;
+	at91sam9_common_init();
 	at91sam9g45_pm_init();
 }
 
@@ -60,16 +96,13 @@
 
 DT_MACHINE_START(at91sam9g45_dt, "Atmel AT91SAM9G45")
 	/* Maintainer: Atmel */
-	.map_io		= at91_map_io,
 	.init_machine	= at91sam9g45_dt_device_init,
 	.dt_compat	= at91sam9g45_board_compat,
 MACHINE_END
 
 static void __init at91sam9x5_dt_device_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
-
-	arm_pm_idle = at91sam9_idle;
+	at91sam9_common_init();
 	at91sam9x5_pm_init();
 }
 
@@ -81,7 +114,6 @@
 
 DT_MACHINE_START(at91sam9x5_dt, "Atmel AT91SAM9")
 	/* Maintainer: Atmel */
-	.map_io		= at91_map_io,
 	.init_machine	= at91sam9x5_dt_device_init,
 	.dt_compat	= at91sam9x5_board_compat,
 MACHINE_END
diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h
index 583369f..2b396c4 100644
--- a/arch/arm/mach-at91/generic.h
+++ b/arch/arm/mach-at91/generic.h
@@ -25,10 +25,6 @@
 extern void at91rm9200_idle(void);
 extern void at91sam9_idle(void);
 
-/* Matrix */
-extern void at91_ioremap_matrix(u32 base_addr);
-
-
 #ifdef CONFIG_PM
 extern void __init at91rm9200_pm_init(void);
 extern void __init at91sam9260_pm_init(void);
diff --git a/arch/arm/mach-at91/include/mach/at91_matrix.h b/arch/arm/mach-at91/include/mach/at91_matrix.h
deleted file mode 100644
index f8996c9..0000000
--- a/arch/arm/mach-at91/include/mach/at91_matrix.h
+++ /dev/null
@@ -1,23 +0,0 @@
-/*
- * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- *
- * Under GPLv2
- */
-
-#ifndef __MACH_AT91_MATRIX_H__
-#define __MACH_AT91_MATRIX_H__
-
-#ifndef __ASSEMBLY__
-extern void __iomem *at91_matrix_base;
-
-#define at91_matrix_read(field) \
-	__raw_readl(at91_matrix_base + field)
-
-#define at91_matrix_write(field, value) \
-	__raw_writel(value, at91_matrix_base + field)
-
-#else
-.extern at91_matrix_base
-#endif
-
-#endif /* __MACH_AT91_MATRIX_H__ */
diff --git a/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h
deleted file mode 100644
index f459df4..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9260_matrix.h
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9260_matrix.h
- *
- *  Copyright (C) 2007 Atmel Corporation.
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91SAM9260 datasheet revision B.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9260_MATRIX_H
-#define AT91SAM9260_MATRIX_H
-
-#define AT91_MATRIX_MCFG0	0x00			/* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1	0x04			/* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2	0x08			/* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3	0x0C			/* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4	0x10			/* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5	0x14			/* Master Configuration Register 5 */
-#define		AT91_MATRIX_ULBT		(7 << 0)	/* Undefined Length Burst Type */
-#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
-#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
-#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
-#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
-#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
-
-#define AT91_MATRIX_SCFG0	0x40			/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	0x44			/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	0x48			/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	0x4C			/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	0x50			/* Slave Configuration Register 4 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0xff <<  0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(7    << 18)	/* Fixed Index of Default Master */
-#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
-#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
-#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
-
-#define AT91_MATRIX_PRAS0	0x80			/* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRAS1	0x88			/* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRAS2	0x90			/* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRAS3	0x98			/* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRAS4	0xA0			/* Priority Register A for Slave 4 */
-#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
-#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
-#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
-#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
-#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
-#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
-
-#define AT91_MATRIX_MRCR	0x100			/* Master Remap Control Register */
-#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-
-#define AT91_MATRIX_EBICSA	0x11C			/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
-#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
-#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define		AT91_MATRIX_VDDIOMSEL		(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_VDDIOMSEL_1_8V	(0 << 16)
-#define			AT91_MATRIX_VDDIOMSEL_3_3V	(1 << 16)
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h
deleted file mode 100644
index a50cdf8..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9261_matrix.h
+++ /dev/null
@@ -1,64 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9261_matrix.h
- *
- *  Copyright (C) 2007 Atmel Corporation.
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91SAM9261 datasheet revision D.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9261_MATRIX_H
-#define AT91SAM9261_MATRIX_H
-
-#define AT91_MATRIX_MCFG	0x00			/* Master Configuration Register */
-#define		AT91_MATRIX_RCB0	(1 << 0)		/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1	(1 << 1)		/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-
-#define AT91_MATRIX_SCFG0	0x04			/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	0x08			/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	0x0C			/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	0x10			/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	0x14			/* Slave Configuration Register 4 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(7    << 18)	/* Fixed Index of Default Master */
-
-#define AT91_MATRIX_TCR		0x24			/* TCM Configuration Register */
-#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
-#define			AT91_MATRIX_ITCM_0		(0 << 0)
-#define			AT91_MATRIX_ITCM_16		(5 << 0)
-#define			AT91_MATRIX_ITCM_32		(6 << 0)
-#define			AT91_MATRIX_ITCM_64		(7 << 0)
-#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
-#define			AT91_MATRIX_DTCM_0		(0 << 4)
-#define			AT91_MATRIX_DTCM_16		(5 << 4)
-#define			AT91_MATRIX_DTCM_32		(6 << 4)
-#define			AT91_MATRIX_DTCM_64		(7 << 4)
-
-#define AT91_MATRIX_EBICSA	0x30			/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
-#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
-#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-
-#define AT91_MATRIX_USBPUCR	0x34			/* USB Pad Pull-Up Control Register */
-#define		AT91_MATRIX_USBPUCR_PUON	(1 << 30)	/* USB Device PAD Pull-up Enable */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h
deleted file mode 100644
index ebb5fdb..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9263_matrix.h
+++ /dev/null
@@ -1,129 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9263_matrix.h
- *
- *  Copyright (C) 2006 Atmel Corporation.
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91SAM9263 datasheet revision B (Preliminary).
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9263_MATRIX_H
-#define AT91SAM9263_MATRIX_H
-
-#define AT91_MATRIX_MCFG0	0x00			/* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1	0x04			/* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2	0x08			/* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3	0x0C			/* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4	0x10			/* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5	0x14			/* Master Configuration Register 5 */
-#define AT91_MATRIX_MCFG6	0x18			/* Master Configuration Register 6 */
-#define AT91_MATRIX_MCFG7	0x1C			/* Master Configuration Register 7 */
-#define AT91_MATRIX_MCFG8	0x20			/* Master Configuration Register 8 */
-#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
-#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
-#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
-#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
-#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
-#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
-
-#define AT91_MATRIX_SCFG0	0x40			/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	0x44			/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	0x48			/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	0x4C			/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	0x50			/* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5	0x54			/* Slave Configuration Register 5 */
-#define AT91_MATRIX_SCFG6	0x58			/* Slave Configuration Register 6 */
-#define AT91_MATRIX_SCFG7	0x5C			/* Slave Configuration Register 7 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(0xf  << 18)	/* Fixed Index of Default Master */
-#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
-#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
-#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
-
-#define AT91_MATRIX_PRAS0	0x80			/* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRBS0	0x84			/* Priority Register B for Slave 0 */
-#define AT91_MATRIX_PRAS1	0x88			/* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRBS1	0x8C			/* Priority Register B for Slave 1 */
-#define AT91_MATRIX_PRAS2	0x90			/* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRBS2	0x94			/* Priority Register B for Slave 2 */
-#define AT91_MATRIX_PRAS3	0x98			/* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRBS3	0x9C			/* Priority Register B for Slave 3 */
-#define AT91_MATRIX_PRAS4	0xA0			/* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRBS4	0xA4			/* Priority Register B for Slave 4 */
-#define AT91_MATRIX_PRAS5	0xA8			/* Priority Register A for Slave 5 */
-#define AT91_MATRIX_PRBS5	0xAC			/* Priority Register B for Slave 5 */
-#define AT91_MATRIX_PRAS6	0xB0			/* Priority Register A for Slave 6 */
-#define AT91_MATRIX_PRBS6	0xB4			/* Priority Register B for Slave 6 */
-#define AT91_MATRIX_PRAS7	0xB8			/* Priority Register A for Slave 7 */
-#define AT91_MATRIX_PRBS7	0xBC			/* Priority Register B for Slave 7 */
-#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
-#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
-#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
-#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
-#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
-#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
-#define		AT91_MATRIX_M6PR		(3 << 24)	/* Master 6 Priority */
-#define		AT91_MATRIX_M7PR		(3 << 28)	/* Master 7 Priority */
-#define		AT91_MATRIX_M8PR		(3 << 0)	/* Master 8 Priority (in Register B) */
-
-#define AT91_MATRIX_MRCR	0x100			/* Master Remap Control Register */
-#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define		AT91_MATRIX_RCB2		(1 << 2)
-#define		AT91_MATRIX_RCB3		(1 << 3)
-#define		AT91_MATRIX_RCB4		(1 << 4)
-#define		AT91_MATRIX_RCB5		(1 << 5)
-#define		AT91_MATRIX_RCB6		(1 << 6)
-#define		AT91_MATRIX_RCB7		(1 << 7)
-#define		AT91_MATRIX_RCB8		(1 << 8)
-
-#define AT91_MATRIX_TCMR	0x114			/* TCM Configuration Register */
-#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
-#define			AT91_MATRIX_ITCM_0		(0 << 0)
-#define			AT91_MATRIX_ITCM_16		(5 << 0)
-#define			AT91_MATRIX_ITCM_32		(6 << 0)
-#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
-#define			AT91_MATRIX_DTCM_0		(0 << 4)
-#define			AT91_MATRIX_DTCM_16		(5 << 4)
-#define			AT91_MATRIX_DTCM_32		(6 << 4)
-
-#define AT91_MATRIX_EBI0CSA	0x120			/* EBI0 Chip Select Assignment Register */
-#define		AT91_MATRIX_EBI0_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_EBI0_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_EBI0_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_EBI0_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_EBI0_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_EBI0_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_EBI0_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_EBI0_CS4A_SMC_CF1		(1 << 4)
-#define		AT91_MATRIX_EBI0_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_EBI0_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_EBI0_CS5A_SMC_CF2		(1 << 5)
-#define		AT91_MATRIX_EBI0_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define		AT91_MATRIX_EBI0_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_EBI0_VDDIOMSEL_1_8V		(0 << 16)
-#define			AT91_MATRIX_EBI0_VDDIOMSEL_3_3V		(1 << 16)
-
-#define AT91_MATRIX_EBI1CSA	0x124			/* EBI1 Chip Select Assignment Register */
-#define		AT91_MATRIX_EBI1_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_EBI1_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_EBI1_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_EBI1_CS2A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_EBI1_CS2A_SMC		(0 << 3)
-#define			AT91_MATRIX_EBI1_CS2A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_EBI1_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define		AT91_MATRIX_EBI1_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_EBI1_VDDIOMSEL_1_8V		(0 << 16)
-#define			AT91_MATRIX_EBI1_VDDIOMSEL_3_3V		(1 << 16)
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h
deleted file mode 100644
index b76e2ed..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9g45_matrix.h
+++ /dev/null
@@ -1,153 +0,0 @@
-/*
- * Matrix-centric header file for the AT91SAM9G45 family
- *
- *  Copyright (C) 2008-2009 Atmel Corporation.
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91SAM9G45 preliminary datasheet.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef AT91SAM9G45_MATRIX_H
-#define AT91SAM9G45_MATRIX_H
-
-#define AT91_MATRIX_MCFG0	0x00			/* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1	0x04			/* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2	0x08			/* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3	0x0C			/* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4	0x10			/* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5	0x14			/* Master Configuration Register 5 */
-#define AT91_MATRIX_MCFG6	0x18			/* Master Configuration Register 6 */
-#define AT91_MATRIX_MCFG7	0x1C			/* Master Configuration Register 7 */
-#define AT91_MATRIX_MCFG8	0x20			/* Master Configuration Register 8 */
-#define AT91_MATRIX_MCFG9	0x24			/* Master Configuration Register 9 */
-#define AT91_MATRIX_MCFG10	0x28			/* Master Configuration Register 10 */
-#define AT91_MATRIX_MCFG11	0x2C			/* Master Configuration Register 11 */
-#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
-#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
-#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
-#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
-#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
-#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
-#define			AT91_MATRIX_ULBT_THIRTYTWO	(5 << 0)
-#define			AT91_MATRIX_ULBT_SIXTYFOUR	(6 << 0)
-#define			AT91_MATRIX_ULBT_128		(7 << 0)
-
-#define AT91_MATRIX_SCFG0	0x40			/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	0x44			/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	0x48			/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	0x4C			/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	0x50			/* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5	0x54			/* Slave Configuration Register 5 */
-#define AT91_MATRIX_SCFG6	0x58			/* Slave Configuration Register 6 */
-#define AT91_MATRIX_SCFG7	0x5C			/* Slave Configuration Register 7 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0x1ff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(0xf  << 18)	/* Fixed Index of Default Master */
-
-#define AT91_MATRIX_PRAS0	0x80			/* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRBS0	0x84			/* Priority Register B for Slave 0 */
-#define AT91_MATRIX_PRAS1	0x88			/* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRBS1	0x8C			/* Priority Register B for Slave 1 */
-#define AT91_MATRIX_PRAS2	0x90			/* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRBS2	0x94			/* Priority Register B for Slave 2 */
-#define AT91_MATRIX_PRAS3	0x98			/* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRBS3	0x9C			/* Priority Register B for Slave 3 */
-#define AT91_MATRIX_PRAS4	0xA0			/* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRBS4	0xA4			/* Priority Register B for Slave 4 */
-#define AT91_MATRIX_PRAS5	0xA8			/* Priority Register A for Slave 5 */
-#define AT91_MATRIX_PRBS5	0xAC			/* Priority Register B for Slave 5 */
-#define AT91_MATRIX_PRAS6	0xB0			/* Priority Register A for Slave 6 */
-#define AT91_MATRIX_PRBS6	0xB4			/* Priority Register B for Slave 6 */
-#define AT91_MATRIX_PRAS7	0xB8			/* Priority Register A for Slave 7 */
-#define AT91_MATRIX_PRBS7	0xBC			/* Priority Register B for Slave 7 */
-#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
-#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
-#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
-#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
-#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
-#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
-#define		AT91_MATRIX_M6PR		(3 << 24)	/* Master 6 Priority */
-#define		AT91_MATRIX_M7PR		(3 << 28)	/* Master 7 Priority */
-#define		AT91_MATRIX_M8PR		(3 << 0)	/* Master 8 Priority (in Register B) */
-#define		AT91_MATRIX_M9PR		(3 << 4)	/* Master 9 Priority (in Register B) */
-#define		AT91_MATRIX_M10PR		(3 << 8)	/* Master 10 Priority (in Register B) */
-#define		AT91_MATRIX_M11PR		(3 << 12)	/* Master 11 Priority (in Register B) */
-
-#define AT91_MATRIX_MRCR	0x100			/* Master Remap Control Register */
-#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define		AT91_MATRIX_RCB2		(1 << 2)
-#define		AT91_MATRIX_RCB3		(1 << 3)
-#define		AT91_MATRIX_RCB4		(1 << 4)
-#define		AT91_MATRIX_RCB5		(1 << 5)
-#define		AT91_MATRIX_RCB6		(1 << 6)
-#define		AT91_MATRIX_RCB7		(1 << 7)
-#define		AT91_MATRIX_RCB8		(1 << 8)
-#define		AT91_MATRIX_RCB9		(1 << 9)
-#define		AT91_MATRIX_RCB10		(1 << 10)
-#define		AT91_MATRIX_RCB11		(1 << 11)
-
-#define AT91_MATRIX_TCMR	0x110			/* TCM Configuration Register */
-#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
-#define			AT91_MATRIX_ITCM_0		(0 << 0)
-#define			AT91_MATRIX_ITCM_32		(6 << 0)
-#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
-#define			AT91_MATRIX_DTCM_0		(0 << 4)
-#define			AT91_MATRIX_DTCM_32		(6 << 4)
-#define			AT91_MATRIX_DTCM_64		(7 << 4)
-#define		AT91_MATRIX_TCM_NWS		(0x1 << 11)	/* Wait state TCM register */
-#define			AT91_MATRIX_TCM_NO_WS		(0x0 << 11)
-#define			AT91_MATRIX_TCM_ONE_WS		(0x1 << 11)
-
-#define AT91_MATRIX_VIDEO	0x118			/* Video Mode Configuration Register */
-#define		AT91C_VDEC_SEL			(0x1 <<  0) /* Video Mode Selection */
-#define			AT91C_VDEC_SEL_OFF		(0 << 0)
-#define			AT91C_VDEC_SEL_ON		(1 << 0)
-
-#define AT91_MATRIX_EBICSA	0x128			/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_EBI_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_EBI_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_EBI_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_EBI_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_EBI_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_EBI_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_EBI_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_EBI_CS4A_SMC_CF0		(1 << 4)
-#define		AT91_MATRIX_EBI_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_EBI_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_EBI_CS5A_SMC_CF1		(1 << 5)
-#define		AT91_MATRIX_EBI_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define			AT91_MATRIX_EBI_DBPU_ON			(0 << 8)
-#define			AT91_MATRIX_EBI_DBPU_OFF		(1 << 8)
-#define		AT91_MATRIX_EBI_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_EBI_VDDIOMSEL_1_8V		(0 << 16)
-#define			AT91_MATRIX_EBI_VDDIOMSEL_3_3V		(1 << 16)
-#define		AT91_MATRIX_EBI_EBI_IOSR	(1 << 17)	/* EBI I/O slew rate selection */
-#define			AT91_MATRIX_EBI_EBI_IOSR_REDUCED	(0 << 17)
-#define			AT91_MATRIX_EBI_EBI_IOSR_NORMAL		(1 << 17)
-#define		AT91_MATRIX_EBI_DDR_IOSR	(1 << 18)	/* DDR2 dedicated port I/O slew rate selection */
-#define			AT91_MATRIX_EBI_DDR_IOSR_REDUCED	(0 << 18)
-#define			AT91_MATRIX_EBI_DDR_IOSR_NORMAL		(1 << 18)
-
-#define AT91_MATRIX_WPMR	0x1E4			/* Write Protect Mode Register */
-#define		AT91_MATRIX_WPMR_WPEN		(1 << 0)	/* Write Protect ENable */
-#define			AT91_MATRIX_WPMR_WP_WPDIS		(0 << 0)
-#define			AT91_MATRIX_WPMR_WP_WPEN		(1 << 0)
-#define		AT91_MATRIX_WPMR_WPKEY		(0xFFFFFF << 8)	/* Write Protect KEY */
-
-#define AT91_MATRIX_WPSR	0x1E8			/* Write Protect Status Register */
-#define		AT91_MATRIX_WPSR_WPVS		(1 << 0)	/* Write Protect Violation Status */
-#define			AT91_MATRIX_WPSR_NO_WPV		(0 << 0)
-#define			AT91_MATRIX_WPSR_WPV		(1 << 0)
-#define		AT91_MATRIX_WPSR_WPVSRC		(0xFFFF << 8)	/* Write Protect Violation Source */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h
deleted file mode 100644
index 40060cd..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9n12_matrix.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * Matrix-centric header file for the AT91SAM9N12
- *
- * Copyright (C) 2012 Atmel Corporation.
- *
- * Only EBI related registers.
- * Write Protect register definitions may be useful.
- *
- * Licensed under GPLv2 or later.
- */
-
-#ifndef _AT91SAM9N12_MATRIX_H_
-#define _AT91SAM9N12_MATRIX_H_
-
-#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x118)	/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_EBI_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_EBI_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_EBI_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_EBI_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_EBI_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH	(1 << 3)
-#define		AT91_MATRIX_EBI_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define			AT91_MATRIX_EBI_DBPU_ON			(0 << 8)
-#define			AT91_MATRIX_EBI_DBPU_OFF		(1 << 8)
-#define		AT91_MATRIX_EBI_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_EBI_VDDIOMSEL_1_8V		(0 << 16)
-#define			AT91_MATRIX_EBI_VDDIOMSEL_3_3V		(1 << 16)
-#define		AT91_MATRIX_EBI_EBI_IOSR	(1 << 17)	/* EBI I/O slew rate selection */
-#define			AT91_MATRIX_EBI_EBI_IOSR_REDUCED	(0 << 17)
-#define			AT91_MATRIX_EBI_EBI_IOSR_NORMAL		(1 << 17)
-#define		AT91_MATRIX_EBI_DDR_IOSR	(1 << 18)	/* DDR2 dedicated port I/O slew rate selection */
-#define			AT91_MATRIX_EBI_DDR_IOSR_REDUCED	(0 << 18)
-#define			AT91_MATRIX_EBI_DDR_IOSR_NORMAL		(1 << 18)
-#define		AT91_MATRIX_NFD0_SELECT		(1 << 24)	/* NAND Flash Data Bus Selection */
-#define			AT91_MATRIX_NFD0_ON_D0			(0 << 24)
-#define			AT91_MATRIX_NFD0_ON_D16			(1 << 24)
-#define		AT91_MATRIX_DDR_MP_EN		(1 << 25)	/* DDR Multi-port Enable */
-#define			AT91_MATRIX_MP_OFF			(0 << 25)
-#define			AT91_MATRIX_MP_ON			(1 << 25)
-
-#define AT91_MATRIX_WPMR	(AT91_MATRIX + 0x1E4)	/* Write Protect Mode Register */
-#define		AT91_MATRIX_WPMR_WPEN		(1 << 0)	/* Write Protect ENable */
-#define			AT91_MATRIX_WPMR_WP_WPDIS		(0 << 0)
-#define			AT91_MATRIX_WPMR_WP_WPEN		(1 << 0)
-#define		AT91_MATRIX_WPMR_WPKEY		(0xFFFFFF << 8)	/* Write Protect KEY */
-
-#define AT91_MATRIX_WPSR	(AT91_MATRIX + 0x1E8)	/* Write Protect Status Register */
-#define		AT91_MATRIX_WPSR_WPVS		(1 << 0)	/* Write Protect Violation Status */
-#define			AT91_MATRIX_WPSR_NO_WPV		(0 << 0)
-#define			AT91_MATRIX_WPSR_WPV		(1 << 0)
-#define		AT91_MATRIX_WPSR_WPVSRC		(0xFFFF << 8)	/* Write Protect Violation Source */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h
deleted file mode 100644
index 6d160ada..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/at91sam9rl_matrix.h
- *
- *  Copyright (C) 2007 Atmel Corporation
- *
- * Memory Controllers (MATRIX, EBI) - System peripherals registers.
- * Based on AT91SAM9RL datasheet revision A. (Preliminary)
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-#ifndef AT91SAM9RL_MATRIX_H
-#define AT91SAM9RL_MATRIX_H
-
-#define AT91_MATRIX_MCFG0	0x00			/* Master Configuration Register 0 */
-#define AT91_MATRIX_MCFG1	0x04			/* Master Configuration Register 1 */
-#define AT91_MATRIX_MCFG2	0x08			/* Master Configuration Register 2 */
-#define AT91_MATRIX_MCFG3	0x0C			/* Master Configuration Register 3 */
-#define AT91_MATRIX_MCFG4	0x10			/* Master Configuration Register 4 */
-#define AT91_MATRIX_MCFG5	0x14			/* Master Configuration Register 5 */
-#define		AT91_MATRIX_ULBT	(7 << 0)	/* Undefined Length Burst Type */
-#define			AT91_MATRIX_ULBT_INFINITE	(0 << 0)
-#define			AT91_MATRIX_ULBT_SINGLE		(1 << 0)
-#define			AT91_MATRIX_ULBT_FOUR		(2 << 0)
-#define			AT91_MATRIX_ULBT_EIGHT		(3 << 0)
-#define			AT91_MATRIX_ULBT_SIXTEEN	(4 << 0)
-
-#define AT91_MATRIX_SCFG0	0x40			/* Slave Configuration Register 0 */
-#define AT91_MATRIX_SCFG1	0x44			/* Slave Configuration Register 1 */
-#define AT91_MATRIX_SCFG2	0x48			/* Slave Configuration Register 2 */
-#define AT91_MATRIX_SCFG3	0x4C			/* Slave Configuration Register 3 */
-#define AT91_MATRIX_SCFG4	0x50			/* Slave Configuration Register 4 */
-#define AT91_MATRIX_SCFG5	0x54			/* Slave Configuration Register 5 */
-#define		AT91_MATRIX_SLOT_CYCLE		(0xff << 0)	/* Maximum Number of Allowed Cycles for a Burst */
-#define		AT91_MATRIX_DEFMSTR_TYPE	(3    << 16)	/* Default Master Type */
-#define			AT91_MATRIX_DEFMSTR_TYPE_NONE	(0 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_LAST	(1 << 16)
-#define			AT91_MATRIX_DEFMSTR_TYPE_FIXED	(2 << 16)
-#define		AT91_MATRIX_FIXED_DEFMSTR	(0xf  << 18)	/* Fixed Index of Default Master */
-#define		AT91_MATRIX_ARBT		(3    << 24)	/* Arbitration Type */
-#define			AT91_MATRIX_ARBT_ROUND_ROBIN	(0 << 24)
-#define			AT91_MATRIX_ARBT_FIXED_PRIORITY	(1 << 24)
-
-#define AT91_MATRIX_PRAS0	0x80			/* Priority Register A for Slave 0 */
-#define AT91_MATRIX_PRAS1	0x88			/* Priority Register A for Slave 1 */
-#define AT91_MATRIX_PRAS2	0x90			/* Priority Register A for Slave 2 */
-#define AT91_MATRIX_PRAS3	0x98			/* Priority Register A for Slave 3 */
-#define AT91_MATRIX_PRAS4	0xA0			/* Priority Register A for Slave 4 */
-#define AT91_MATRIX_PRAS5	0xA8			/* Priority Register A for Slave 5 */
-#define		AT91_MATRIX_M0PR		(3 << 0)	/* Master 0 Priority */
-#define		AT91_MATRIX_M1PR		(3 << 4)	/* Master 1 Priority */
-#define		AT91_MATRIX_M2PR		(3 << 8)	/* Master 2 Priority */
-#define		AT91_MATRIX_M3PR		(3 << 12)	/* Master 3 Priority */
-#define		AT91_MATRIX_M4PR		(3 << 16)	/* Master 4 Priority */
-#define		AT91_MATRIX_M5PR		(3 << 20)	/* Master 5 Priority */
-
-#define AT91_MATRIX_MRCR	0x100			/* Master Remap Control Register */
-#define		AT91_MATRIX_RCB0		(1 << 0)	/* Remap Command for AHB Master 0 (ARM926EJ-S Instruction Master) */
-#define		AT91_MATRIX_RCB1		(1 << 1)	/* Remap Command for AHB Master 1 (ARM926EJ-S Data Master) */
-#define		AT91_MATRIX_RCB2		(1 << 2)
-#define		AT91_MATRIX_RCB3		(1 << 3)
-#define		AT91_MATRIX_RCB4		(1 << 4)
-#define		AT91_MATRIX_RCB5		(1 << 5)
-
-#define AT91_MATRIX_TCMR	0x114			/* TCM Configuration Register */
-#define		AT91_MATRIX_ITCM_SIZE		(0xf << 0)	/* Size of ITCM enabled memory block */
-#define			AT91_MATRIX_ITCM_0		(0 << 0)
-#define			AT91_MATRIX_ITCM_16		(5 << 0)
-#define			AT91_MATRIX_ITCM_32		(6 << 0)
-#define		AT91_MATRIX_DTCM_SIZE		(0xf << 4)	/* Size of DTCM enabled memory block */
-#define			AT91_MATRIX_DTCM_0		(0 << 4)
-#define			AT91_MATRIX_DTCM_16		(5 << 4)
-#define			AT91_MATRIX_DTCM_32		(6 << 4)
-
-#define AT91_MATRIX_EBICSA	0x120			/* EBI0 Chip Select Assignment Register */
-#define		AT91_MATRIX_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_CS3A_SMC_SMARTMEDIA	(1 << 3)
-#define		AT91_MATRIX_CS4A		(1 << 4)	/* Chip Select 4 Assignment */
-#define			AT91_MATRIX_CS4A_SMC		(0 << 4)
-#define			AT91_MATRIX_CS4A_SMC_CF1	(1 << 4)
-#define		AT91_MATRIX_CS5A		(1 << 5)	/* Chip Select 5 Assignment */
-#define			AT91_MATRIX_CS5A_SMC		(0 << 5)
-#define			AT91_MATRIX_CS5A_SMC_CF2	(1 << 5)
-#define		AT91_MATRIX_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define		AT91_MATRIX_VDDIOMSEL		(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_VDDIOMSEL_1_8V	(0 << 16)
-#define			AT91_MATRIX_VDDIOMSEL_3_3V	(1 << 16)
-
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h b/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h
deleted file mode 100644
index a606d39..0000000
--- a/arch/arm/mach-at91/include/mach/at91sam9x5_matrix.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * Matrix-centric header file for the AT91SAM9x5 family
- *
- *  Copyright (C) 2009-2012 Atmel Corporation.
- *
- * Only EBI related registers.
- * Write Protect register definitions may be useful.
- *
- * Licensed under GPLv2 or later.
- */
-
-#ifndef AT91SAM9X5_MATRIX_H
-#define AT91SAM9X5_MATRIX_H
-
-#define AT91_MATRIX_EBICSA	(AT91_MATRIX + 0x120)	/* EBI Chip Select Assignment Register */
-#define		AT91_MATRIX_EBI_CS1A		(1 << 1)	/* Chip Select 1 Assignment */
-#define			AT91_MATRIX_EBI_CS1A_SMC		(0 << 1)
-#define			AT91_MATRIX_EBI_CS1A_SDRAMC		(1 << 1)
-#define		AT91_MATRIX_EBI_CS3A		(1 << 3)	/* Chip Select 3 Assignment */
-#define			AT91_MATRIX_EBI_CS3A_SMC		(0 << 3)
-#define			AT91_MATRIX_EBI_CS3A_SMC_NANDFLASH	(1 << 3)
-#define		AT91_MATRIX_EBI_DBPUC		(1 << 8)	/* Data Bus Pull-up Configuration */
-#define			AT91_MATRIX_EBI_DBPU_ON			(0 << 8)
-#define			AT91_MATRIX_EBI_DBPU_OFF		(1 << 8)
-#define		AT91_MATRIX_EBI_VDDIOMSEL	(1 << 16)	/* Memory voltage selection */
-#define			AT91_MATRIX_EBI_VDDIOMSEL_1_8V		(0 << 16)
-#define			AT91_MATRIX_EBI_VDDIOMSEL_3_3V		(1 << 16)
-#define		AT91_MATRIX_EBI_EBI_IOSR	(1 << 17)	/* EBI I/O slew rate selection */
-#define			AT91_MATRIX_EBI_EBI_IOSR_REDUCED	(0 << 17)
-#define			AT91_MATRIX_EBI_EBI_IOSR_NORMAL		(1 << 17)
-#define		AT91_MATRIX_EBI_DDR_IOSR	(1 << 18)	/* DDR2 dedicated port I/O slew rate selection */
-#define			AT91_MATRIX_EBI_DDR_IOSR_REDUCED	(0 << 18)
-#define			AT91_MATRIX_EBI_DDR_IOSR_NORMAL		(1 << 18)
-#define		AT91_MATRIX_NFD0_SELECT		(1 << 24)	/* NAND Flash Data Bus Selection */
-#define			AT91_MATRIX_NFD0_ON_D0			(0 << 24)
-#define			AT91_MATRIX_NFD0_ON_D16			(1 << 24)
-#define		AT91_MATRIX_DDR_MP_EN		(1 << 25)	/* DDR Multi-port Enable */
-#define			AT91_MATRIX_MP_OFF			(0 << 25)
-#define			AT91_MATRIX_MP_ON			(1 << 25)
-
-#define AT91_MATRIX_WPMR	(AT91_MATRIX + 0x1E4)	/* Write Protect Mode Register */
-#define		AT91_MATRIX_WPMR_WPEN		(1 << 0)	/* Write Protect ENable */
-#define			AT91_MATRIX_WPMR_WP_WPDIS		(0 << 0)
-#define			AT91_MATRIX_WPMR_WP_WPEN		(1 << 0)
-#define		AT91_MATRIX_WPMR_WPKEY		(0xFFFFFF << 8)	/* Write Protect KEY */
-
-#define AT91_MATRIX_WPSR	(AT91_MATRIX + 0x1E8)	/* Write Protect Status Register */
-#define		AT91_MATRIX_WPSR_WPVS		(1 << 0)	/* Write Protect Violation Status */
-#define			AT91_MATRIX_WPSR_NO_WPV		(0 << 0)
-#define			AT91_MATRIX_WPSR_WPV		(1 << 0)
-#define		AT91_MATRIX_WPSR_WPVSRC		(0xFFFF << 8)	/* Write Protect Violation Source */
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/io.h b/arch/arm/mach-at91/include/mach/io.h
deleted file mode 100644
index 2d9ca04..0000000
--- a/arch/arm/mach-at91/include/mach/io.h
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * arch/arm/mach-at91/include/mach/io.h
- *
- *  Copyright (C) 2003 SAN People
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#ifndef __ASM_ARCH_IO_H
-#define __ASM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT		0xFFFFFFFF
-#define __io(a)			__typesafe_io(a)
-
-#endif
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index aa4116e..ac947cd 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -29,6 +29,8 @@
 #include <linux/atomic.h>
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
+#include <asm/fncpy.h>
+#include <asm/cacheflush.h>
 
 #include <mach/cpu.h>
 #include <mach/hardware.h>
@@ -41,7 +43,6 @@
 	int memctrl;
 } at91_pm_data;
 
-static void (*at91_pm_standby)(void);
 void __iomem *at91_ramc_base[2];
 
 static int at91_pm_valid_state(suspend_state_t state)
@@ -119,76 +120,67 @@
 }
 EXPORT_SYMBOL(at91_suspend_entering_slow_clock);
 
-
-static void (*slow_clock)(void __iomem *pmc, void __iomem *ramc0,
+static void (*at91_suspend_sram_fn)(void __iomem *pmc, void __iomem *ramc0,
 			  void __iomem *ramc1, int memctrl);
 
-#ifdef CONFIG_AT91_SLOW_CLOCK
-extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0,
+extern void at91_pm_suspend_in_sram(void __iomem *pmc, void __iomem *ramc0,
 			    void __iomem *ramc1, int memctrl);
-extern u32 at91_slow_clock_sz;
-#endif
+extern u32 at91_pm_suspend_in_sram_sz;
+
+static void at91_pm_suspend(suspend_state_t state)
+{
+	unsigned int pm_data = at91_pm_data.memctrl;
+
+	pm_data |= (state == PM_SUSPEND_MEM) ?
+				AT91_PM_MODE(AT91_PM_SLOW_CLOCK) : 0;
+
+	flush_cache_all();
+	outer_disable();
+
+	at91_suspend_sram_fn(at91_pmc_base, at91_ramc_base[0],
+				at91_ramc_base[1], pm_data);
+
+	outer_resume();
+}
 
 static int at91_pm_enter(suspend_state_t state)
 {
 	at91_pinctrl_gpio_suspend();
 
 	switch (state) {
+	/*
+	 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
+	 * drivers must suspend more deeply, the master clock switches
+	 * to the clk32k and turns off the main oscillator
+	 */
+	case PM_SUSPEND_MEM:
 		/*
-		 * Suspend-to-RAM is like STANDBY plus slow clock mode, so
-		 * drivers must suspend more deeply:  only the master clock
-		 * controller may be using the main oscillator.
+		 * Ensure that clocks are in a valid state.
 		 */
-		case PM_SUSPEND_MEM:
-			/*
-			 * Ensure that clocks are in a valid state.
-			 */
-			if (!at91_pm_verify_clocks())
-				goto error;
-
-			/*
-			 * Enter slow clock mode by switching over to clk32k and
-			 * turning off the main oscillator; reverse on wakeup.
-			 */
-			if (slow_clock) {
-#ifdef CONFIG_AT91_SLOW_CLOCK
-				/* copy slow_clock handler to SRAM, and call it */
-				memcpy(slow_clock, at91_slow_clock, at91_slow_clock_sz);
-#endif
-				slow_clock(at91_pmc_base, at91_ramc_base[0],
-					   at91_ramc_base[1],
-					   at91_pm_data.memctrl);
-				break;
-			} else {
-				pr_info("AT91: PM - no slow clock mode enabled ...\n");
-				/* FALLTHROUGH leaving master clock alone */
-			}
-
-		/*
-		 * STANDBY mode has *all* drivers suspended; ignores irqs not
-		 * marked as 'wakeup' event sources; and reduces DRAM power.
-		 * But otherwise it's identical to PM_SUSPEND_ON:  cpu idle, and
-		 * nothing fancy done with main or cpu clocks.
-		 */
-		case PM_SUSPEND_STANDBY:
-			/*
-			 * NOTE: the Wait-for-Interrupt instruction needs to be
-			 * in icache so no SDRAM accesses are needed until the
-			 * wakeup IRQ occurs and self-refresh is terminated.
-			 * For ARM 926 based chips, this requirement is weaker
-			 * as at91sam9 can access a RAM in self-refresh mode.
-			 */
-			if (at91_pm_standby)
-				at91_pm_standby();
-			break;
-
-		case PM_SUSPEND_ON:
-			cpu_do_idle();
-			break;
-
-		default:
-			pr_debug("AT91: PM - bogus suspend state %d\n", state);
+		if (!at91_pm_verify_clocks())
 			goto error;
+
+		at91_pm_suspend(state);
+
+		break;
+
+	/*
+	 * STANDBY mode has *all* drivers suspended; ignores irqs not
+	 * marked as 'wakeup' event sources; and reduces DRAM power.
+	 * But otherwise it's identical to PM_SUSPEND_ON: cpu idle, and
+	 * nothing fancy done with main or cpu clocks.
+	 */
+	case PM_SUSPEND_STANDBY:
+		at91_pm_suspend(state);
+		break;
+
+	case PM_SUSPEND_ON:
+		cpu_do_idle();
+		break;
+
+	default:
+		pr_debug("AT91: PM - bogus suspend state %d\n", state);
+		goto error;
 	}
 
 error:
@@ -218,12 +210,10 @@
 	.name = "cpuidle-at91",
 };
 
-void at91_pm_set_standby(void (*at91_standby)(void))
+static void at91_pm_set_standby(void (*at91_standby)(void))
 {
-	if (at91_standby) {
+	if (at91_standby)
 		at91_cpuidle_device.dev.platform_data = at91_standby;
-		at91_pm_standby = at91_standby;
-	}
 }
 
 static const struct of_device_id ramc_ids[] __initconst = {
@@ -263,7 +253,6 @@
 	at91_pm_set_standby(standby);
 }
 
-#ifdef CONFIG_AT91_SLOW_CLOCK
 static void __init at91_pm_sram_init(void)
 {
 	struct gen_pool *sram_pool;
@@ -291,30 +280,36 @@
 		return;
 	}
 
-	sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz);
+	sram_base = gen_pool_alloc(sram_pool, at91_pm_suspend_in_sram_sz);
 	if (!sram_base) {
-		pr_warn("%s: unable to alloc ocram!\n", __func__);
+		pr_warn("%s: unable to alloc sram!\n", __func__);
 		return;
 	}
 
 	sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base);
-	slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false);
-}
-#endif
+	at91_suspend_sram_fn = __arm_ioremap_exec(sram_pbase,
+					at91_pm_suspend_in_sram_sz, false);
+	if (!at91_suspend_sram_fn) {
+		pr_warn("SRAM: Could not map\n");
+		return;
+	}
 
+	/* Copy the pm suspend handler to SRAM */
+	at91_suspend_sram_fn = fncpy(at91_suspend_sram_fn,
+			&at91_pm_suspend_in_sram, at91_pm_suspend_in_sram_sz);
+}
 
 static void __init at91_pm_init(void)
 {
-#ifdef CONFIG_AT91_SLOW_CLOCK
 	at91_pm_sram_init();
-#endif
-
-	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
 	if (at91_cpuidle_device.dev.platform_data)
 		platform_device_register(&at91_cpuidle_device);
 
-	suspend_set_ops(&at91_pm_ops);
+	if (at91_suspend_sram_fn)
+		suspend_set_ops(&at91_pm_ops);
+	else
+		pr_info("AT91: PM not supported, due to no SRAM allocated\n");
 }
 
 void __init at91rm9200_pm_init(void)
diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h
index 86c0aa8..dcacfa1 100644
--- a/arch/arm/mach-at91/pm.h
+++ b/arch/arm/mach-at91/pm.h
@@ -15,11 +15,13 @@
 
 #include <mach/at91_ramc.h>
 
-#ifdef CONFIG_PM
-extern void at91_pm_set_standby(void (*at91_standby)(void));
-#else
-static inline void at91_pm_set_standby(void (*at91_standby)(void)) { }
-#endif
+#define	AT91_PM_MEMTYPE_MASK	0x0f
+
+#define	AT91_PM_MODE_OFFSET	4
+#define	AT91_PM_MODE_MASK	0x01
+#define	AT91_PM_MODE(x)		(((x) & AT91_PM_MODE_MASK) << AT91_PM_MODE_OFFSET)
+
+#define	AT91_PM_SLOW_CLOCK	0x01
 
 /*
  * The AT91RM9200 goes into self-refresh mode with this command, and will
@@ -31,6 +33,7 @@
  * still in self-refresh is "not recommended", but seems to work.
  */
 
+#ifndef __ASSEMBLY__
 static inline void at91rm9200_standby(void)
 {
 	u32 lpr = at91_ramc_read(0, AT91RM9200_SDRAMC_LPR);
@@ -112,3 +115,4 @@
 }
 
 #endif
+#endif
diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S
deleted file mode 100644
index 931f0e3..0000000
--- a/arch/arm/mach-at91/pm_slowclock.S
+++ /dev/null
@@ -1,335 +0,0 @@
-/*
- * arch/arm/mach-at91/pm_slow_clock.S
- *
- *  Copyright (C) 2006 Savin Zlobec
- *
- * AT91SAM9 support:
- *  Copyright (C) 2007 Anti Sullin <anti.sullin@artecdesign.ee
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/linkage.h>
-#include <linux/clk/at91_pmc.h>
-#include <mach/hardware.h>
-#include <mach/at91_ramc.h>
-
-/*
- * When SLOWDOWN_MASTER_CLOCK is defined we will also slow down the Master
- * clock during suspend by adjusting its prescalar and divisor.
- * NOTE: This hasn't been shown to be stable on SAM9s; and on the RM9200 there
- *       are errata regarding adjusting the prescalar and divisor.
- */
-#undef SLOWDOWN_MASTER_CLOCK
-
-pmc	.req	r0
-sdramc	.req	r1
-ramc1	.req	r2
-memctrl	.req	r3
-tmp1	.req	r4
-tmp2	.req	r5
-
-/*
- * Wait until master clock is ready (after switching master clock source)
- */
-	.macro wait_mckrdy
-1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
-	tst	tmp1, #AT91_PMC_MCKRDY
-	beq	1b
-	.endm
-
-/*
- * Wait until master oscillator has stabilized.
- */
-	.macro wait_moscrdy
-1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
-	tst	tmp1, #AT91_PMC_MOSCS
-	beq	1b
-	.endm
-
-/*
- * Wait until PLLA has locked.
- */
-	.macro wait_pllalock
-1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
-	tst	tmp1, #AT91_PMC_LOCKA
-	beq	1b
-	.endm
-
-/*
- * Wait until PLLB has locked.
- */
-	.macro wait_pllblock
-1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
-	tst	tmp1, #AT91_PMC_LOCKB
-	beq	1b
-	.endm
-
-	.text
-
-	.arm
-
-/* void at91_slow_clock(void __iomem *pmc, void __iomem *sdramc,
- *			void __iomem *ramc1, int memctrl)
- */
-ENTRY(at91_slow_clock)
-	/* Save registers on stack */
-	stmfd	sp!, {r4 - r12, lr}
-
-	/*
-	 * Register usage:
-	 *  R0 = Base address of AT91_PMC
-	 *  R1 = Base address of RAM Controller (SDRAM, DDRSDR, or AT91_SYS)
-	 *  R2 = Base address of second RAM Controller or 0 if not present
-	 *  R3 = Memory controller
-	 *  R4 = temporary register
-	 *  R5 = temporary register
-	 */
-
-	/* Drain write buffer */
-	mov	tmp1, #0
-	mcr	p15, 0, tmp1, c7, c10, 4
-
-	cmp	memctrl, #AT91_MEMCTRL_MC
-	bne	ddr_sr_enable
-
-	/*
-	 * at91rm9200 Memory controller
-	 */
-	/* Put SDRAM in self-refresh mode */
-	mov	tmp1, #1
-	str	tmp1, [sdramc, #AT91RM9200_SDRAMC_SRR]
-	b	sdr_sr_done
-
-	/*
-	 * DDRSDR Memory controller
-	 */
-ddr_sr_enable:
-	cmp	memctrl, #AT91_MEMCTRL_DDRSDR
-	bne	sdr_sr_enable
-
-	/* LPDDR1 --> force DDR2 mode during self-refresh */
-	ldr	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
-	str	tmp1, .saved_sam9_mdr
-	bic	tmp1, tmp1, #~AT91_DDRSDRC_MD
-	cmp	tmp1, #AT91_DDRSDRC_MD_LOW_POWER_DDR
-	ldreq	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
-	biceq	tmp1, tmp1, #AT91_DDRSDRC_MD
-	orreq	tmp1, tmp1, #AT91_DDRSDRC_MD_DDR2
-	streq	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
-
-	/* prepare for DDRAM self-refresh mode */
-	ldr	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
-	str	tmp1, .saved_sam9_lpr
-	bic	tmp1, #AT91_DDRSDRC_LPCB
-	orr	tmp1, #AT91_DDRSDRC_LPCB_SELF_REFRESH
-
-	/* figure out if we use the second ram controller */
-	cmp	ramc1, #0
-	beq	ddr_no_2nd_ctrl
-
-	ldr	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
-	str	tmp2, .saved_sam9_mdr1
-	bic	tmp2, tmp2, #~AT91_DDRSDRC_MD
-	cmp	tmp2, #AT91_DDRSDRC_MD_LOW_POWER_DDR
-	ldreq	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
-	biceq	tmp2, tmp2, #AT91_DDRSDRC_MD
-	orreq	tmp2, tmp2, #AT91_DDRSDRC_MD_DDR2
-	streq	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
-
-	ldr	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
-	str	tmp2, .saved_sam9_lpr1
-	bic	tmp2, #AT91_DDRSDRC_LPCB
-	orr	tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
-
-	/* Enable DDRAM self-refresh mode */
-	str	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
-ddr_no_2nd_ctrl:
-	str	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
-
-	b	sdr_sr_done
-
-	/*
-	 * SDRAMC Memory controller
-	 */
-sdr_sr_enable:
-	/* Enable SDRAM self-refresh mode */
-	ldr	tmp1, [sdramc, #AT91_SDRAMC_LPR]
-	str	tmp1, .saved_sam9_lpr
-
-	bic	tmp1, #AT91_SDRAMC_LPCB
-	orr	tmp1, #AT91_SDRAMC_LPCB_SELF_REFRESH
-	str	tmp1, [sdramc, #AT91_SDRAMC_LPR]
-
-sdr_sr_done:
-	/* Save Master clock setting */
-	ldr	tmp1, [pmc, #AT91_PMC_MCKR]
-	str	tmp1, .saved_mckr
-
-	/*
-	 * Set the Master clock source to slow clock
-	 */
-	bic	tmp1, tmp1, #AT91_PMC_CSS
-	str	tmp1, [pmc, #AT91_PMC_MCKR]
-
-	wait_mckrdy
-
-#ifdef SLOWDOWN_MASTER_CLOCK
-	/*
-	 * Set the Master Clock PRES and MDIV fields.
-	 *
-	 * See AT91RM9200 errata #27 and #28 for details.
-	 */
-	mov	tmp1, #0
-	str	tmp1, [pmc, #AT91_PMC_MCKR]
-
-	wait_mckrdy
-#endif
-
-	/* Save PLLA setting and disable it */
-	ldr	tmp1, [pmc, #AT91_CKGR_PLLAR]
-	str	tmp1, .saved_pllar
-
-	mov	tmp1, #AT91_PMC_PLLCOUNT
-	orr	tmp1, tmp1, #(1 << 29)		/* bit 29 always set */
-	str	tmp1, [pmc, #AT91_CKGR_PLLAR]
-
-	/* Save PLLB setting and disable it */
-	ldr	tmp1, [pmc, #AT91_CKGR_PLLBR]
-	str	tmp1, .saved_pllbr
-
-	mov	tmp1, #AT91_PMC_PLLCOUNT
-	str	tmp1, [pmc, #AT91_CKGR_PLLBR]
-
-	/* Turn off the main oscillator */
-	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
-	bic	tmp1, tmp1, #AT91_PMC_MOSCEN
-	orr	tmp1, tmp1, #AT91_PMC_KEY
-	str	tmp1, [pmc, #AT91_CKGR_MOR]
-
-	/* Wait for interrupt */
-	mcr	p15, 0, tmp1, c7, c0, 4
-
-	/* Turn on the main oscillator */
-	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
-	orr	tmp1, tmp1, #AT91_PMC_MOSCEN
-	orr	tmp1, tmp1, #AT91_PMC_KEY
-	str	tmp1, [pmc, #AT91_CKGR_MOR]
-
-	wait_moscrdy
-
-	/* Restore PLLB setting */
-	ldr	tmp1, .saved_pllbr
-	str	tmp1, [pmc, #AT91_CKGR_PLLBR]
-
-	tst	tmp1, #(AT91_PMC_MUL &  0xff0000)
-	bne	1f
-	tst	tmp1, #(AT91_PMC_MUL & ~0xff0000)
-	beq	2f
-1:
-	wait_pllblock
-2:
-
-	/* Restore PLLA setting */
-	ldr	tmp1, .saved_pllar
-	str	tmp1, [pmc, #AT91_CKGR_PLLAR]
-
-	tst	tmp1, #(AT91_PMC_MUL &  0xff0000)
-	bne	3f
-	tst	tmp1, #(AT91_PMC_MUL & ~0xff0000)
-	beq	4f
-3:
-	wait_pllalock
-4:
-
-#ifdef SLOWDOWN_MASTER_CLOCK
-	/*
-	 * First set PRES if it was not 0,
-	 * than set CSS and MDIV fields.
-	 *
-	 * See AT91RM9200 errata #27 and #28 for details.
-	 */
-	ldr	tmp1, .saved_mckr
-	tst	tmp1, #AT91_PMC_PRES
-	beq	2f
-	and	tmp1, tmp1, #AT91_PMC_PRES
-	str	tmp1, [pmc, #AT91_PMC_MCKR]
-
-	wait_mckrdy
-#endif
-
-	/*
-	 * Restore master clock setting
-	 */
-2:	ldr	tmp1, .saved_mckr
-	str	tmp1, [pmc, #AT91_PMC_MCKR]
-
-	wait_mckrdy
-
-	/*
-	 * at91rm9200 Memory controller
-	 * Do nothing - self-refresh is automatically disabled.
-	 */
-	cmp	memctrl, #AT91_MEMCTRL_MC
-	beq	ram_restored
-
-	/*
-	 * DDRSDR Memory controller
-	 */
-	cmp	memctrl, #AT91_MEMCTRL_DDRSDR
-	bne	sdr_en_restore
-	/* Restore MDR in case of LPDDR1 */
-	ldr	tmp1, .saved_sam9_mdr
-	str	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
-	/* Restore LPR on AT91 with DDRAM */
-	ldr	tmp1, .saved_sam9_lpr
-	str	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
-
-	/* if we use the second ram controller */
-	cmp	ramc1, #0
-	ldrne	tmp2, .saved_sam9_mdr1
-	strne	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
-	ldrne	tmp2, .saved_sam9_lpr1
-	strne	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
-
-	b	ram_restored
-
-	/*
-	 * SDRAMC Memory controller
-	 */
-sdr_en_restore:
-	/* Restore LPR on AT91 with SDRAM */
-	ldr	tmp1, .saved_sam9_lpr
-	str	tmp1, [sdramc, #AT91_SDRAMC_LPR]
-
-ram_restored:
-	/* Restore registers, and return */
-	ldmfd	sp!, {r4 - r12, pc}
-
-
-.saved_mckr:
-	.word 0
-
-.saved_pllar:
-	.word 0
-
-.saved_pllbr:
-	.word 0
-
-.saved_sam9_lpr:
-	.word 0
-
-.saved_sam9_lpr1:
-	.word 0
-
-.saved_sam9_mdr:
-	.word 0
-
-.saved_sam9_mdr1:
-	.word 0
-
-ENTRY(at91_slow_clock_sz)
-	.word .-at91_slow_clock
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
new file mode 100644
index 0000000..7c444c2
--- /dev/null
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -0,0 +1,338 @@
+/*
+ * arch/arm/mach-at91/pm_slow_clock.S
+ *
+ *  Copyright (C) 2006 Savin Zlobec
+ *
+ * AT91SAM9 support:
+ *  Copyright (C) 2007 Anti Sullin <anti.sullin@artecdesign.ee
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include <linux/linkage.h>
+#include <linux/clk/at91_pmc.h>
+#include <mach/hardware.h>
+#include <mach/at91_ramc.h>
+#include "pm.h"
+
+#define	SRAMC_SELF_FRESH_ACTIVE		0x01
+#define	SRAMC_SELF_FRESH_EXIT		0x00
+
+pmc	.req	r0
+tmp1	.req	r4
+tmp2	.req	r5
+
+/*
+ * Wait until master clock is ready (after switching master clock source)
+ */
+	.macro wait_mckrdy
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
+	tst	tmp1, #AT91_PMC_MCKRDY
+	beq	1b
+	.endm
+
+/*
+ * Wait until master oscillator has stabilized.
+ */
+	.macro wait_moscrdy
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
+	tst	tmp1, #AT91_PMC_MOSCS
+	beq	1b
+	.endm
+
+/*
+ * Wait until PLLA has locked.
+ */
+	.macro wait_pllalock
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
+	tst	tmp1, #AT91_PMC_LOCKA
+	beq	1b
+	.endm
+
+/*
+ * Put the processor to enter the idle state
+ */
+	.macro at91_cpu_idle
+
+#if defined(CONFIG_CPU_V7)
+	mov	tmp1, #AT91_PMC_PCK
+	str	tmp1, [pmc, #AT91_PMC_SCDR]
+
+	dsb
+
+	wfi		@ Wait For Interrupt
+#else
+	mcr	p15, 0, tmp1, c7, c0, 4
+#endif
+
+	.endm
+
+	.text
+
+	.arm
+
+/*
+ * void at91_pm_suspend_in_sram(void __iomem *pmc, void __iomem *sdramc,
+ *			void __iomem *ramc1, int memctrl)
+ * @input param:
+ * 	@r0: base address of AT91_PMC
+ *  	@r1: base address of SDRAM Controller (SDRAM, DDRSDR, or AT91_SYS)
+ *	@r2: base address of second SDRAM Controller or 0 if not present
+ *	@r3: pm information
+ */
+ENTRY(at91_pm_suspend_in_sram)
+	/* Save registers on stack */
+	stmfd	sp!, {r4 - r12, lr}
+
+	/* Drain write buffer */
+	mov	tmp1, #0
+	mcr	p15, 0, tmp1, c7, c10, 4
+
+	str	r0, .pmc_base
+	str	r1, .sramc_base
+	str	r2, .sramc1_base
+
+	and	r0, r3, #AT91_PM_MEMTYPE_MASK
+	str	r0, .memtype
+
+	lsr	r0, r3, #AT91_PM_MODE_OFFSET
+	and	r0, r0, #AT91_PM_MODE_MASK
+	str	r0, .pm_mode
+
+	/* Active the self-refresh mode */
+	mov	r0, #SRAMC_SELF_FRESH_ACTIVE
+	bl	at91_sramc_self_refresh
+
+	ldr	r0, .pm_mode
+	tst	r0, #AT91_PM_SLOW_CLOCK
+	beq	skip_disable_main_clock
+
+	ldr	pmc, .pmc_base
+
+	/* Save Master clock setting */
+	ldr	tmp1, [pmc, #AT91_PMC_MCKR]
+	str	tmp1, .saved_mckr
+
+	/*
+	 * Set the Master clock source to slow clock
+	 */
+	bic	tmp1, tmp1, #AT91_PMC_CSS
+	str	tmp1, [pmc, #AT91_PMC_MCKR]
+
+	wait_mckrdy
+
+	/* Save PLLA setting and disable it */
+	ldr	tmp1, [pmc, #AT91_CKGR_PLLAR]
+	str	tmp1, .saved_pllar
+
+	mov	tmp1, #AT91_PMC_PLLCOUNT
+	orr	tmp1, tmp1, #(1 << 29)		/* bit 29 always set */
+	str	tmp1, [pmc, #AT91_CKGR_PLLAR]
+
+	/* Turn off the main oscillator */
+	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
+	bic	tmp1, tmp1, #AT91_PMC_MOSCEN
+	orr	tmp1, tmp1, #AT91_PMC_KEY
+	str	tmp1, [pmc, #AT91_CKGR_MOR]
+
+skip_disable_main_clock:
+	ldr	pmc, .pmc_base
+
+	/* Wait for interrupt */
+	at91_cpu_idle
+
+	ldr	r0, .pm_mode
+	tst	r0, #AT91_PM_SLOW_CLOCK
+	beq	skip_enable_main_clock
+
+	ldr	pmc, .pmc_base
+
+	/* Turn on the main oscillator */
+	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
+	orr	tmp1, tmp1, #AT91_PMC_MOSCEN
+	orr	tmp1, tmp1, #AT91_PMC_KEY
+	str	tmp1, [pmc, #AT91_CKGR_MOR]
+
+	wait_moscrdy
+
+	/* Restore PLLA setting */
+	ldr	tmp1, .saved_pllar
+	str	tmp1, [pmc, #AT91_CKGR_PLLAR]
+
+	tst	tmp1, #(AT91_PMC_MUL &  0xff0000)
+	bne	3f
+	tst	tmp1, #(AT91_PMC_MUL & ~0xff0000)
+	beq	4f
+3:
+	wait_pllalock
+4:
+
+	/*
+	 * Restore master clock setting
+	 */
+	ldr	tmp1, .saved_mckr
+	str	tmp1, [pmc, #AT91_PMC_MCKR]
+
+	wait_mckrdy
+
+skip_enable_main_clock:
+	/* Exit the self-refresh mode */
+	mov	r0, #SRAMC_SELF_FRESH_EXIT
+	bl	at91_sramc_self_refresh
+
+	/* Restore registers, and return */
+	ldmfd	sp!, {r4 - r12, pc}
+ENDPROC(at91_pm_suspend_in_sram)
+
+/*
+ * void at91_sramc_self_refresh(unsigned int is_active)
+ *
+ * @input param:
+ *	@r0: 1 - active self-refresh mode
+ *	     0 - exit self-refresh mode
+ * register usage:
+ * 	@r1: memory type
+ *	@r2: base address of the sram controller
+ */
+
+ENTRY(at91_sramc_self_refresh)
+	ldr	r1, .memtype
+	ldr	r2, .sramc_base
+
+	cmp	r1, #AT91_MEMCTRL_MC
+	bne	ddrc_sf
+
+	/*
+	 * at91rm9200 Memory controller
+	 */
+
+	 /*
+	  * For exiting the self-refresh mode, do nothing,
+	  * automatically exit the self-refresh mode.
+	  */
+	tst	r0, #SRAMC_SELF_FRESH_ACTIVE
+	beq	exit_sramc_sf
+
+	/* Active SDRAM self-refresh mode */
+	mov	r3, #1
+	str	r3, [r2, #AT91RM9200_SDRAMC_SRR]
+	b	exit_sramc_sf
+
+ddrc_sf:
+	cmp	r1, #AT91_MEMCTRL_DDRSDR
+	bne	sdramc_sf
+
+	/*
+	 * DDR Memory controller
+	 */
+	tst	r0, #SRAMC_SELF_FRESH_ACTIVE
+	beq	ddrc_exit_sf
+
+	/* LPDDR1 --> force DDR2 mode during self-refresh */
+	ldr	r3, [r2, #AT91_DDRSDRC_MDR]
+	str	r3, .saved_sam9_mdr
+	bic	r3, r3, #~AT91_DDRSDRC_MD
+	cmp	r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+	ldreq	r3, [r2, #AT91_DDRSDRC_MDR]
+	biceq	r3, r3, #AT91_DDRSDRC_MD
+	orreq	r3, r3, #AT91_DDRSDRC_MD_DDR2
+	streq	r3, [r2, #AT91_DDRSDRC_MDR]
+
+	/* Active DDRC self-refresh mode */
+	ldr	r3, [r2, #AT91_DDRSDRC_LPR]
+	str	r3, .saved_sam9_lpr
+	bic	r3, r3, #AT91_DDRSDRC_LPCB
+	orr	r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+	str	r3, [r2, #AT91_DDRSDRC_LPR]
+
+	/* If using the 2nd ddr controller */
+	ldr	r2, .sramc1_base
+	cmp	r2, #0
+	beq	no_2nd_ddrc
+
+	ldr	r3, [r2, #AT91_DDRSDRC_MDR]
+	str	r3, .saved_sam9_mdr1
+	bic	r3, r3, #~AT91_DDRSDRC_MD
+	cmp	r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+	ldreq	r3, [r2, #AT91_DDRSDRC_MDR]
+	biceq	r3, r3, #AT91_DDRSDRC_MD
+	orreq	r3, r3, #AT91_DDRSDRC_MD_DDR2
+	streq	r3, [r2, #AT91_DDRSDRC_MDR]
+
+	/* Active DDRC self-refresh mode */
+	ldr	r3, [r2, #AT91_DDRSDRC_LPR]
+	str	r3, .saved_sam9_lpr1
+	bic	r3, r3, #AT91_DDRSDRC_LPCB
+	orr	r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+	str	r3, [r2, #AT91_DDRSDRC_LPR]
+
+no_2nd_ddrc:
+	b	exit_sramc_sf
+
+ddrc_exit_sf:
+	/* Restore MDR in case of LPDDR1 */
+	ldr	r3, .saved_sam9_mdr
+	str	r3, [r2, #AT91_DDRSDRC_MDR]
+	/* Restore LPR on AT91 with DDRAM */
+	ldr	r3, .saved_sam9_lpr
+	str	r3, [r2, #AT91_DDRSDRC_LPR]
+
+	/* If using the 2nd ddr controller */
+	ldr	r2, .sramc1_base
+	cmp	r2, #0
+	ldrne	r3, .saved_sam9_mdr1
+	strne	r3, [r2, #AT91_DDRSDRC_MDR]
+	ldrne	r3, .saved_sam9_lpr1
+	strne	r3, [r2, #AT91_DDRSDRC_LPR]
+
+	b	exit_sramc_sf
+
+	/*
+	 * SDRAMC Memory controller
+	 */
+sdramc_sf:
+	tst	r0, #SRAMC_SELF_FRESH_ACTIVE
+	beq	sdramc_exit_sf
+
+	/* Active SDRAMC self-refresh mode */
+	ldr	r3, [r2, #AT91_SDRAMC_LPR]
+	str	r3, .saved_sam9_lpr
+	bic	r3, r3, #AT91_SDRAMC_LPCB
+	orr	r3, r3, #AT91_SDRAMC_LPCB_SELF_REFRESH
+	str	r3, [r2, #AT91_SDRAMC_LPR]
+
+sdramc_exit_sf:
+	ldr	r3, .saved_sam9_lpr
+	str	r3, [r2, #AT91_SDRAMC_LPR]
+
+exit_sramc_sf:
+	mov	pc, lr
+ENDPROC(at91_sramc_self_refresh)
+
+.pmc_base:
+	.word 0
+.sramc_base:
+	.word 0
+.sramc1_base:
+	.word 0
+.memtype:
+	.word 0
+.pm_mode:
+	.word 0
+.saved_mckr:
+	.word 0
+.saved_pllar:
+	.word 0
+.saved_sam9_lpr:
+	.word 0
+.saved_sam9_lpr1:
+	.word 0
+.saved_sam9_mdr:
+	.word 0
+.saved_sam9_mdr1:
+	.word 0
+
+ENTRY(at91_pm_suspend_in_sram_sz)
+	.word .-at91_pm_suspend_in_sram
diff --git a/arch/arm/mach-at91/sama5.c b/arch/arm/mach-at91/sama5.c
index 03dcb44..ef5d207 100644
--- a/arch/arm/mach-at91/sama5.c
+++ b/arch/arm/mach-at91/sama5.c
@@ -7,48 +7,50 @@
  * Licensed under GPLv2 or later.
  */
 
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/gpio.h>
-#include <linux/micrel_phy.h>
 #include <linux/of.h>
-#include <linux/of_irq.h>
 #include <linux/of_platform.h>
-#include <linux/phy.h>
-#include <linux/clk-provider.h>
-#include <linux/phy.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/system_misc.h>
 
 #include <mach/hardware.h>
 
-#include <asm/setup.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
 #include "generic.h"
+#include "soc.h"
 
-static int ksz8081_phy_fixup(struct phy_device *phy)
-{
-	int value;
-
-	value = phy_read(phy, 0x16);
-	value &= ~0x20;
-	phy_write(phy, 0x16, value);
-
-	return 0;
-}
+static const struct at91_soc sama5_socs[] = {
+	AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D31_EXID_MATCH,
+		 "sama5d31", "sama5d3"),
+	AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D33_EXID_MATCH,
+		 "sama5d33", "sama5d3"),
+	AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D34_EXID_MATCH,
+		 "sama5d34", "sama5d3"),
+	AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D35_EXID_MATCH,
+		 "sama5d35", "sama5d3"),
+	AT91_SOC(SAMA5D3_CIDR_MATCH, SAMA5D36_EXID_MATCH,
+		 "sama5d36", "sama5d3"),
+	AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D41_EXID_MATCH,
+		 "sama5d41", "sama5d4"),
+	AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D42_EXID_MATCH,
+		 "sama5d42", "sama5d4"),
+	AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D43_EXID_MATCH,
+		 "sama5d43", "sama5d4"),
+	AT91_SOC(SAMA5D4_CIDR_MATCH, SAMA5D44_EXID_MATCH,
+		 "sama5d44", "sama5d4"),
+	{ /* sentinel */ },
+};
 
 static void __init sama5_dt_device_init(void)
 {
-	if (of_machine_is_compatible("atmel,sama5d4ek") &&
-	   IS_ENABLED(CONFIG_PHYLIB)) {
-		phy_register_fixup_for_id("fc028000.etherne:00",
-						ksz8081_phy_fixup);
-	}
+	struct soc_device *soc;
+	struct device *soc_dev = NULL;
 
-	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+	soc = at91_soc_init(sama5_socs);
+	if (soc != NULL)
+		soc_dev = soc_device_to_device(soc);
+
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, soc_dev);
 	at91sam9x5_pm_init();
 }
 
@@ -59,44 +61,10 @@
 
 DT_MACHINE_START(sama5_dt, "Atmel SAMA5")
 	/* Maintainer: Atmel */
-	.map_io		= at91_map_io,
 	.init_machine	= sama5_dt_device_init,
 	.dt_compat	= sama5_dt_board_compat,
 MACHINE_END
 
-static struct map_desc at91_io_desc[] __initdata = {
-	{
-	.virtual        = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_MPDDRC),
-	.pfn            = __phys_to_pfn(SAMA5D4_BASE_MPDDRC),
-	.length         = SZ_512,
-	.type           = MT_DEVICE,
-	},
-	{
-	.virtual        = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_PMC),
-	.pfn            = __phys_to_pfn(SAMA5D4_BASE_PMC),
-	.length         = SZ_512,
-	.type           = MT_DEVICE,
-	},
-	{ /* On sama5d4, we use USART3 as serial console */
-	.virtual        = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_USART3),
-	.pfn            = __phys_to_pfn(SAMA5D4_BASE_USART3),
-	.length         = SZ_256,
-	.type           = MT_DEVICE,
-	},
-	{ /* A bunch of peripheral with fine grained IO space */
-	.virtual        = (unsigned long)AT91_ALT_IO_P2V(SAMA5D4_BASE_SYS2),
-	.pfn            = __phys_to_pfn(SAMA5D4_BASE_SYS2),
-	.length         = SZ_2K,
-	.type           = MT_DEVICE,
-	},
-};
-
-static void __init sama5_alt_map_io(void)
-{
-	at91_alt_map_io();
-	iotable_init(at91_io_desc, ARRAY_SIZE(at91_io_desc));
-}
-
 static const char *sama5_alt_dt_board_compat[] __initconst = {
 	"atmel,sama5d4",
 	NULL
@@ -104,7 +72,6 @@
 
 DT_MACHINE_START(sama5_alt_dt, "Atmel SAMA5")
 	/* Maintainer: Atmel */
-	.map_io		= sama5_alt_map_io,
 	.init_machine	= sama5_dt_device_init,
 	.dt_compat	= sama5_alt_dt_board_compat,
 	.l2c_aux_mask	= ~0UL,
diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c
deleted file mode 100644
index 4e58bc9..0000000
--- a/arch/arm/mach-at91/setup.c
+++ /dev/null
@@ -1,330 +0,0 @@
-/*
- * Copyright (C) 2007 Atmel Corporation.
- * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
- *
- * Under GPLv2
- */
-
-#define pr_fmt(fmt)	"AT91: " fmt
-
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/mm.h>
-#include <linux/pm.h>
-#include <linux/of_address.h>
-#include <linux/pinctrl/machine.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/system_misc.h>
-#include <asm/mach/map.h>
-
-#include <mach/hardware.h>
-#include <mach/cpu.h>
-#include <mach/at91_dbgu.h>
-
-#include "generic.h"
-#include "pm.h"
-
-struct at91_socinfo at91_soc_initdata;
-EXPORT_SYMBOL(at91_soc_initdata);
-
-static struct map_desc at91_io_desc __initdata __maybe_unused = {
-	.virtual	= (unsigned long)AT91_VA_BASE_SYS,
-	.pfn		= __phys_to_pfn(AT91_BASE_SYS),
-	.length		= SZ_16K,
-	.type		= MT_DEVICE,
-};
-
-static struct map_desc at91_alt_io_desc __initdata __maybe_unused = {
-	.virtual	= (unsigned long)AT91_ALT_VA_BASE_SYS,
-	.pfn		= __phys_to_pfn(AT91_ALT_BASE_SYS),
-	.length		= 24 * SZ_1K,
-	.type		= MT_DEVICE,
-};
-
-static void __init soc_detect(u32 dbgu_base)
-{
-	u32 cidr, socid;
-
-	cidr = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_CIDR);
-	socid = cidr & ~AT91_CIDR_VERSION;
-
-	switch (socid) {
-	case ARCH_ID_AT91RM9200:
-		at91_soc_initdata.type = AT91_SOC_RM9200;
-		if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_UNKNOWN)
-			at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA;
-		break;
-
-	case ARCH_ID_AT91SAM9260:
-		at91_soc_initdata.type = AT91_SOC_SAM9260;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-		break;
-
-	case ARCH_ID_AT91SAM9261:
-		at91_soc_initdata.type = AT91_SOC_SAM9261;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-		break;
-
-	case ARCH_ID_AT91SAM9263:
-		at91_soc_initdata.type = AT91_SOC_SAM9263;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-		break;
-
-	case ARCH_ID_AT91SAM9G20:
-		at91_soc_initdata.type = AT91_SOC_SAM9G20;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-		break;
-
-	case ARCH_ID_AT91SAM9G45:
-		at91_soc_initdata.type = AT91_SOC_SAM9G45;
-		if (cidr == ARCH_ID_AT91SAM9G45ES)
-			at91_soc_initdata.subtype = AT91_SOC_SAM9G45ES;
-		break;
-
-	case ARCH_ID_AT91SAM9RL64:
-		at91_soc_initdata.type = AT91_SOC_SAM9RL;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-		break;
-
-	case ARCH_ID_AT91SAM9X5:
-		at91_soc_initdata.type = AT91_SOC_SAM9X5;
-		break;
-
-	case ARCH_ID_AT91SAM9N12:
-		at91_soc_initdata.type = AT91_SOC_SAM9N12;
-		break;
-
-	case ARCH_ID_SAMA5:
-		at91_soc_initdata.exid = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_EXID);
-		if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D3) {
-			at91_soc_initdata.type = AT91_SOC_SAMA5D3;
-		}
-		break;
-	}
-
-	/* at91sam9g10 */
-	if ((socid & ~AT91_CIDR_EXT) == ARCH_ID_AT91SAM9G10) {
-		at91_soc_initdata.type = AT91_SOC_SAM9G10;
-		at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE;
-	}
-	/* at91sam9xe */
-	else if ((cidr & AT91_CIDR_ARCH) == ARCH_FAMILY_AT91SAM9XE) {
-		at91_soc_initdata.type = AT91_SOC_SAM9260;
-		at91_soc_initdata.subtype = AT91_SOC_SAM9XE;
-	}
-
-	if (!at91_soc_is_detected())
-		return;
-
-	at91_soc_initdata.cidr = cidr;
-
-	/* sub version of soc */
-	if (!at91_soc_initdata.exid)
-		at91_soc_initdata.exid = __raw_readl(AT91_IO_P2V(dbgu_base) + AT91_DBGU_EXID);
-
-	if (at91_soc_initdata.type == AT91_SOC_SAM9G45) {
-		switch (at91_soc_initdata.exid) {
-		case ARCH_EXID_AT91SAM9M10:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9M10;
-			break;
-		case ARCH_EXID_AT91SAM9G46:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9G46;
-			break;
-		case ARCH_EXID_AT91SAM9M11:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9M11;
-			break;
-		}
-	}
-
-	if (at91_soc_initdata.type == AT91_SOC_SAM9X5) {
-		switch (at91_soc_initdata.exid) {
-		case ARCH_EXID_AT91SAM9G15:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9G15;
-			break;
-		case ARCH_EXID_AT91SAM9G35:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9G35;
-			break;
-		case ARCH_EXID_AT91SAM9X35:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9X35;
-			break;
-		case ARCH_EXID_AT91SAM9G25:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9G25;
-			break;
-		case ARCH_EXID_AT91SAM9X25:
-			at91_soc_initdata.subtype = AT91_SOC_SAM9X25;
-			break;
-		}
-	}
-
-	if (at91_soc_initdata.type == AT91_SOC_SAMA5D3) {
-		switch (at91_soc_initdata.exid) {
-		case ARCH_EXID_SAMA5D31:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D31;
-			break;
-		case ARCH_EXID_SAMA5D33:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D33;
-			break;
-		case ARCH_EXID_SAMA5D34:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D34;
-			break;
-		case ARCH_EXID_SAMA5D35:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D35;
-			break;
-		case ARCH_EXID_SAMA5D36:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D36;
-			break;
-		}
-	}
-}
-
-static void __init alt_soc_detect(u32 dbgu_base)
-{
-	u32 cidr, socid;
-
-	/* SoC ID */
-	cidr = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_CIDR);
-	socid = cidr & ~AT91_CIDR_VERSION;
-
-	switch (socid) {
-	case ARCH_ID_SAMA5:
-		at91_soc_initdata.exid = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_EXID);
-		if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D3) {
-			at91_soc_initdata.type = AT91_SOC_SAMA5D3;
-		} else if (at91_soc_initdata.exid & ARCH_EXID_SAMA5D4) {
-			at91_soc_initdata.type = AT91_SOC_SAMA5D4;
-		}
-		break;
-	}
-
-	if (!at91_soc_is_detected())
-		return;
-
-	at91_soc_initdata.cidr = cidr;
-
-	/* sub version of soc */
-	if (!at91_soc_initdata.exid)
-		at91_soc_initdata.exid = __raw_readl(AT91_ALT_IO_P2V(dbgu_base) + AT91_DBGU_EXID);
-
-	if (at91_soc_initdata.type == AT91_SOC_SAMA5D4) {
-		switch (at91_soc_initdata.exid) {
-		case ARCH_EXID_SAMA5D41:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D41;
-			break;
-		case ARCH_EXID_SAMA5D42:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D42;
-			break;
-		case ARCH_EXID_SAMA5D43:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D43;
-			break;
-		case ARCH_EXID_SAMA5D44:
-			at91_soc_initdata.subtype = AT91_SOC_SAMA5D44;
-			break;
-		}
-	}
-}
-
-static const char *soc_name[] = {
-	[AT91_SOC_RM9200]	= "at91rm9200",
-	[AT91_SOC_SAM9260]	= "at91sam9260",
-	[AT91_SOC_SAM9261]	= "at91sam9261",
-	[AT91_SOC_SAM9263]	= "at91sam9263",
-	[AT91_SOC_SAM9G10]	= "at91sam9g10",
-	[AT91_SOC_SAM9G20]	= "at91sam9g20",
-	[AT91_SOC_SAM9G45]	= "at91sam9g45",
-	[AT91_SOC_SAM9RL]	= "at91sam9rl",
-	[AT91_SOC_SAM9X5]	= "at91sam9x5",
-	[AT91_SOC_SAM9N12]	= "at91sam9n12",
-	[AT91_SOC_SAMA5D3]	= "sama5d3",
-	[AT91_SOC_SAMA5D4]	= "sama5d4",
-	[AT91_SOC_UNKNOWN]	= "Unknown",
-};
-
-const char *at91_get_soc_type(struct at91_socinfo *c)
-{
-	return soc_name[c->type];
-}
-EXPORT_SYMBOL(at91_get_soc_type);
-
-static const char *soc_subtype_name[] = {
-	[AT91_SOC_RM9200_BGA]	= "at91rm9200 BGA",
-	[AT91_SOC_RM9200_PQFP]	= "at91rm9200 PQFP",
-	[AT91_SOC_SAM9XE]	= "at91sam9xe",
-	[AT91_SOC_SAM9G45ES]	= "at91sam9g45es",
-	[AT91_SOC_SAM9M10]	= "at91sam9m10",
-	[AT91_SOC_SAM9G46]	= "at91sam9g46",
-	[AT91_SOC_SAM9M11]	= "at91sam9m11",
-	[AT91_SOC_SAM9G15]	= "at91sam9g15",
-	[AT91_SOC_SAM9G35]	= "at91sam9g35",
-	[AT91_SOC_SAM9X35]	= "at91sam9x35",
-	[AT91_SOC_SAM9G25]	= "at91sam9g25",
-	[AT91_SOC_SAM9X25]	= "at91sam9x25",
-	[AT91_SOC_SAMA5D31]	= "sama5d31",
-	[AT91_SOC_SAMA5D33]	= "sama5d33",
-	[AT91_SOC_SAMA5D34]	= "sama5d34",
-	[AT91_SOC_SAMA5D35]	= "sama5d35",
-	[AT91_SOC_SAMA5D36]	= "sama5d36",
-	[AT91_SOC_SAMA5D41]	= "sama5d41",
-	[AT91_SOC_SAMA5D42]	= "sama5d42",
-	[AT91_SOC_SAMA5D43]	= "sama5d43",
-	[AT91_SOC_SAMA5D44]	= "sama5d44",
-	[AT91_SOC_SUBTYPE_NONE]	= "None",
-	[AT91_SOC_SUBTYPE_UNKNOWN] = "Unknown",
-};
-
-const char *at91_get_soc_subtype(struct at91_socinfo *c)
-{
-	return soc_subtype_name[c->subtype];
-}
-EXPORT_SYMBOL(at91_get_soc_subtype);
-
-void __init at91_map_io(void)
-{
-	/* Map peripherals */
-	iotable_init(&at91_io_desc, 1);
-
-	at91_soc_initdata.type = AT91_SOC_UNKNOWN;
-	at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_UNKNOWN;
-
-	soc_detect(AT91_BASE_DBGU0);
-	if (!at91_soc_is_detected())
-		soc_detect(AT91_BASE_DBGU1);
-
-	if (!at91_soc_is_detected())
-		panic(pr_fmt("Impossible to detect the SOC type"));
-
-	pr_info("Detected soc type: %s\n",
-		at91_get_soc_type(&at91_soc_initdata));
-	if (at91_soc_initdata.subtype != AT91_SOC_SUBTYPE_NONE)
-		pr_info("Detected soc subtype: %s\n",
-			at91_get_soc_subtype(&at91_soc_initdata));
-}
-
-void __init at91_alt_map_io(void)
-{
-	/* Map peripherals */
-	iotable_init(&at91_alt_io_desc, 1);
-
-	at91_soc_initdata.type = AT91_SOC_UNKNOWN;
-	at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_UNKNOWN;
-
-	alt_soc_detect(AT91_BASE_DBGU2);
-	if (!at91_soc_is_detected())
-		panic("AT91: Impossible to detect the SOC type");
-
-	pr_info("AT91: Detected soc type: %s\n",
-		at91_get_soc_type(&at91_soc_initdata));
-	if (at91_soc_initdata.subtype != AT91_SOC_SUBTYPE_NONE)
-		pr_info("AT91: Detected soc subtype: %s\n",
-			at91_get_soc_subtype(&at91_soc_initdata));
-}
-
-void __iomem *at91_matrix_base;
-EXPORT_SYMBOL_GPL(at91_matrix_base);
-
-void __init at91_ioremap_matrix(u32 base_addr)
-{
-	at91_matrix_base = ioremap(base_addr, 512);
-	if (!at91_matrix_base)
-		panic(pr_fmt("Impossible to ioremap at91_matrix_base\n"));
-}
diff --git a/arch/arm/mach-at91/soc.c b/arch/arm/mach-at91/soc.c
new file mode 100644
index 0000000..54343ff
--- /dev/null
+++ b/arch/arm/mach-at91/soc.c
@@ -0,0 +1,97 @@
+/*
+ * Copyright (C) 2015 Atmel
+ *
+ * Alexandre Belloni <alexandre.belloni@free-electrons.com
+ * Boris Brezillon <boris.brezillon@free-electrons.com
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ */
+
+#define pr_fmt(fmt)	"AT91: " fmt
+
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+#include <linux/sys_soc.h>
+
+#include "soc.h"
+
+#define AT91_DBGU_CIDR			0x40
+#define AT91_DBGU_CIDR_VERSION(x)	((x) & 0x1f)
+#define AT91_DBGU_CIDR_EXT		BIT(31)
+#define AT91_DBGU_CIDR_MATCH_MASK	0x7fffffe0
+#define AT91_DBGU_EXID			0x44
+
+struct soc_device * __init at91_soc_init(const struct at91_soc *socs)
+{
+	struct soc_device_attribute *soc_dev_attr;
+	const struct at91_soc *soc;
+	struct soc_device *soc_dev;
+	struct device_node *np;
+	void __iomem *regs;
+	u32 cidr, exid;
+
+	np = of_find_compatible_node(NULL, NULL, "atmel,at91rm9200-dbgu");
+	if (!np)
+		np = of_find_compatible_node(NULL, NULL,
+					     "atmel,at91sam9260-dbgu");
+
+	if (!np) {
+		pr_warn("Could not find DBGU node");
+		return NULL;
+	}
+
+	regs = of_iomap(np, 0);
+	of_node_put(np);
+
+	if (!regs) {
+		pr_warn("Could not map DBGU iomem range");
+		return NULL;
+	}
+
+	cidr = readl(regs + AT91_DBGU_CIDR);
+	exid = readl(regs + AT91_DBGU_EXID);
+
+	iounmap(regs);
+
+	for (soc = socs; soc->name; soc++) {
+		if (soc->cidr_match != (cidr & AT91_DBGU_CIDR_MATCH_MASK))
+			continue;
+
+		if (!(cidr & AT91_DBGU_CIDR_EXT) || soc->exid_match == exid)
+			break;
+	}
+
+	if (!soc->name) {
+		pr_warn("Could not find matching SoC description\n");
+		return NULL;
+	}
+
+	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
+	if (!soc_dev_attr)
+		return NULL;
+
+	soc_dev_attr->family = soc->family;
+	soc_dev_attr->soc_id = soc->name;
+	soc_dev_attr->revision = kasprintf(GFP_KERNEL, "%X",
+					   AT91_DBGU_CIDR_VERSION(cidr));
+	soc_dev = soc_device_register(soc_dev_attr);
+	if (IS_ERR(soc_dev)) {
+		kfree(soc_dev_attr->revision);
+		kfree(soc_dev_attr);
+		pr_warn("Could not register SoC device\n");
+		return NULL;
+	}
+
+	if (soc->family)
+		pr_info("Detected SoC family: %s\n", soc->family);
+	pr_info("Detected SoC: %s, revision %X\n", soc->name,
+		AT91_DBGU_CIDR_VERSION(cidr));
+
+	return soc_dev;
+}
diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h
new file mode 100644
index 0000000..be23c40
--- /dev/null
+++ b/arch/arm/mach-at91/soc.h
@@ -0,0 +1,78 @@
+/*
+ * Copyright (C) 2015 Atmel
+ *
+ * Boris Brezillon <boris.brezillon@free-electrons.com
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ */
+
+#ifndef __AT91_SOC_H
+#define __AT91_SOC_H
+
+#include <linux/sys_soc.h>
+
+struct at91_soc {
+	u32 cidr_match;
+	u32 exid_match;
+	const char *name;
+	const char *family;
+};
+
+#define AT91_SOC(__cidr, __exid, __name, __family)		\
+	{							\
+		.cidr_match = (__cidr),				\
+		.exid_match = (__exid),				\
+		.name = (__name),				\
+		.family = (__family),				\
+	}
+
+struct soc_device * __init
+at91_soc_init(const struct at91_soc *socs);
+
+#define AT91RM9200_CIDR_MATCH		0x09290780
+
+#define AT91SAM9260_CIDR_MATCH		0x019803a0
+#define AT91SAM9261_CIDR_MATCH		0x019703a0
+#define AT91SAM9263_CIDR_MATCH		0x019607a0
+#define AT91SAM9G20_CIDR_MATCH		0x019905a0
+#define AT91SAM9RL64_CIDR_MATCH		0x019b03a0
+#define AT91SAM9G45_CIDR_MATCH		0x019b05a0
+#define AT91SAM9X5_CIDR_MATCH		0x019a05a0
+#define AT91SAM9N12_CIDR_MATCH		0x019a07a0
+
+#define AT91SAM9M11_EXID_MATCH		0x00000001
+#define AT91SAM9M10_EXID_MATCH		0x00000002
+#define AT91SAM9G46_EXID_MATCH		0x00000003
+#define AT91SAM9G45_EXID_MATCH		0x00000004
+
+#define AT91SAM9G15_EXID_MATCH		0x00000000
+#define AT91SAM9G35_EXID_MATCH		0x00000001
+#define AT91SAM9X35_EXID_MATCH		0x00000002
+#define AT91SAM9G25_EXID_MATCH		0x00000003
+#define AT91SAM9X25_EXID_MATCH		0x00000004
+
+#define AT91SAM9CN12_EXID_MATCH		0x00000005
+#define AT91SAM9N12_EXID_MATCH		0x00000006
+#define AT91SAM9CN11_EXID_MATCH		0x00000009
+
+#define AT91SAM9XE128_CIDR_MATCH	0x329973a0
+#define AT91SAM9XE256_CIDR_MATCH	0x329a93a0
+#define AT91SAM9XE512_CIDR_MATCH	0x329aa3a0
+
+#define SAMA5D3_CIDR_MATCH		0x0a5c07c0
+#define SAMA5D31_EXID_MATCH		0x00444300
+#define SAMA5D33_EXID_MATCH		0x00414300
+#define SAMA5D34_EXID_MATCH		0x00414301
+#define SAMA5D35_EXID_MATCH		0x00584300
+#define SAMA5D36_EXID_MATCH		0x00004301
+
+#define SAMA5D4_CIDR_MATCH		0x0a5c07c0
+#define SAMA5D41_EXID_MATCH		0x00000001
+#define SAMA5D42_EXID_MATCH		0x00000002
+#define SAMA5D43_EXID_MATCH		0x00000003
+#define SAMA5D44_EXID_MATCH		0x00000004
+
+#endif /* __AT91_SOC_H */
diff --git a/arch/arm/mach-davinci/asp.h b/arch/arm/mach-davinci/asp.h
index d9b2acd..1128e1d 100644
--- a/arch/arm/mach-davinci/asp.h
+++ b/arch/arm/mach-davinci/asp.h
@@ -21,6 +21,9 @@
 /* Bases of da830 McASP1 register banks */
 #define DAVINCI_DA830_MCASP1_REG_BASE	0x01D04000
 
+/* Bases of da830 McASP2 register banks */
+#define DAVINCI_DA830_MCASP2_REG_BASE	0x01D08000
+
 /* EDMA channels of dm644x and dm355 */
 #define DAVINCI_DMA_ASP0_TX	2
 #define DAVINCI_DMA_ASP0_RX	3
@@ -40,6 +43,10 @@
 #define DAVINCI_DA830_DMA_MCASP1_AREVT	2
 #define DAVINCI_DA830_DMA_MCASP1_AXEVT	3
 
+/* EDMA channels of da830 McASP2 */
+#define DAVINCI_DA830_DMA_MCASP2_AREVT	4
+#define DAVINCI_DA830_DMA_MCASP2_AXEVT	5
+
 /* Interrupts */
 #define DAVINCI_ASP0_RX_INT	IRQ_MBRINT
 #define DAVINCI_ASP0_TX_INT	IRQ_MBXINT
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index b85b781..ddfdd82 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -463,16 +463,23 @@
 	},
 	/* TX event */
 	{
+		.name	= "tx",
 		.start	= DAVINCI_DA830_DMA_MCASP1_AXEVT,
 		.end	= DAVINCI_DA830_DMA_MCASP1_AXEVT,
 		.flags	= IORESOURCE_DMA,
 	},
 	/* RX event */
 	{
+		.name	= "rx",
 		.start	= DAVINCI_DA830_DMA_MCASP1_AREVT,
 		.end	= DAVINCI_DA830_DMA_MCASP1_AREVT,
 		.flags	= IORESOURCE_DMA,
 	},
+	{
+		.name	= "common",
+		.start	= IRQ_DA8XX_MCASPINT,
+		.flags	= IORESOURCE_IRQ,
+	},
 };
 
 static struct platform_device da830_mcasp1_device = {
@@ -482,6 +489,41 @@
 	.resource	= da830_mcasp1_resources,
 };
 
+static struct resource da830_mcasp2_resources[] = {
+	{
+		.name	= "mpu",
+		.start	= DAVINCI_DA830_MCASP2_REG_BASE,
+		.end	= DAVINCI_DA830_MCASP2_REG_BASE + (SZ_1K * 12) - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	/* TX event */
+	{
+		.name	= "tx",
+		.start	= DAVINCI_DA830_DMA_MCASP2_AXEVT,
+		.end	= DAVINCI_DA830_DMA_MCASP2_AXEVT,
+		.flags	= IORESOURCE_DMA,
+	},
+	/* RX event */
+	{
+		.name	= "rx",
+		.start	= DAVINCI_DA830_DMA_MCASP2_AREVT,
+		.end	= DAVINCI_DA830_DMA_MCASP2_AREVT,
+		.flags	= IORESOURCE_DMA,
+	},
+	{
+		.name	= "common",
+		.start	= IRQ_DA8XX_MCASPINT,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device da830_mcasp2_device = {
+	.name		= "davinci-mcasp",
+	.id		= 2,
+	.num_resources	= ARRAY_SIZE(da830_mcasp2_resources),
+	.resource	= da830_mcasp2_resources,
+};
+
 static struct resource da850_mcasp_resources[] = {
 	{
 		.name	= "mpu",
@@ -491,16 +533,23 @@
 	},
 	/* TX event */
 	{
+		.name	= "tx",
 		.start	= DAVINCI_DA8XX_DMA_MCASP0_AXEVT,
 		.end	= DAVINCI_DA8XX_DMA_MCASP0_AXEVT,
 		.flags	= IORESOURCE_DMA,
 	},
 	/* RX event */
 	{
+		.name	= "rx",
 		.start	= DAVINCI_DA8XX_DMA_MCASP0_AREVT,
 		.end	= DAVINCI_DA8XX_DMA_MCASP0_AREVT,
 		.flags	= IORESOURCE_DMA,
 	},
+	{
+		.name	= "common",
+		.start	= IRQ_DA8XX_MCASPINT,
+		.flags	= IORESOURCE_IRQ,
+	},
 };
 
 static struct platform_device da850_mcasp_device = {
@@ -512,14 +561,31 @@
 
 void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata)
 {
-	/* DA830/OMAP-L137 has 3 instances of McASP */
-	if (cpu_is_davinci_da830() && id == 1) {
-		da830_mcasp1_device.dev.platform_data = pdata;
-		platform_device_register(&da830_mcasp1_device);
-	} else if (cpu_is_davinci_da850()) {
-		da850_mcasp_device.dev.platform_data = pdata;
-		platform_device_register(&da850_mcasp_device);
+	struct platform_device *pdev;
+
+	switch (id) {
+	case 0:
+		/* Valid for DA830/OMAP-L137 or DA850/OMAP-L138 */
+		pdev = &da850_mcasp_device;
+		break;
+	case 1:
+		/* Valid for DA830/OMAP-L137 only */
+		if (!cpu_is_davinci_da830())
+			return;
+		pdev = &da830_mcasp1_device;
+		break;
+	case 2:
+		/* Valid for DA830/OMAP-L137 only */
+		if (!cpu_is_davinci_da830())
+			return;
+		pdev = &da830_mcasp2_device;
+		break;
+	default:
+		return;
 	}
+
+	pdev->dev.platform_data = pdata;
+	platform_device_register(pdev);
 }
 
 static struct resource da8xx_pruss_resources[] = {
diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
index 6c3bbea..3f842bb 100644
--- a/arch/arm/mach-davinci/dm646x.c
+++ b/arch/arm/mach-davinci/dm646x.c
@@ -493,7 +493,6 @@
 	[IRQ_DM646X_EMACMISCINT]        = 7,
 	[IRQ_DM646X_MCASP0TXINT]        = 7,
 	[IRQ_DM646X_MCASP0RXINT]        = 7,
-	[IRQ_AEMIFINT]                  = 7,
 	[IRQ_DM646X_RESERVED_3]         = 7,
 	[IRQ_DM646X_MCASP1TXINT]        = 7,    /* clockevent */
 	[IRQ_TINT0_TINT34]              = 7,    /* clocksource */
@@ -610,19 +609,31 @@
 		.end 	= DAVINCI_DM646X_MCASP0_REG_BASE + (SZ_1K << 1) - 1,
 		.flags 	= IORESOURCE_MEM,
 	},
-	/* first TX, then RX */
 	{
+		.name	= "tx",
 		.start	= DAVINCI_DM646X_DMA_MCASP0_AXEVT0,
 		.end	= DAVINCI_DM646X_DMA_MCASP0_AXEVT0,
 		.flags	= IORESOURCE_DMA,
 	},
 	{
+		.name	= "rx",
 		.start	= DAVINCI_DM646X_DMA_MCASP0_AREVT0,
 		.end	= DAVINCI_DM646X_DMA_MCASP0_AREVT0,
 		.flags	= IORESOURCE_DMA,
 	},
+	{
+		.name	= "tx",
+		.start	= IRQ_DM646X_MCASP0TXINT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	{
+		.name	= "rx",
+		.start	= IRQ_DM646X_MCASP0RXINT,
+		.flags	= IORESOURCE_IRQ,
+	},
 };
 
+/* DIT mode only, rx is not supported */
 static struct resource dm646x_mcasp1_resources[] = {
 	{
 		.name	= "mpu",
@@ -630,17 +641,16 @@
 		.end	= DAVINCI_DM646X_MCASP1_REG_BASE + (SZ_1K << 1) - 1,
 		.flags	= IORESOURCE_MEM,
 	},
-	/* DIT mode, only TX event */
 	{
+		.name	= "tx",
 		.start	= DAVINCI_DM646X_DMA_MCASP1_AXEVT1,
 		.end	= DAVINCI_DM646X_DMA_MCASP1_AXEVT1,
 		.flags	= IORESOURCE_DMA,
 	},
-	/* DIT mode, dummy entry */
 	{
-		.start	= -1,
-		.end	= -1,
-		.flags	= IORESOURCE_DMA,
+		.name	= "tx",
+		.start	= IRQ_DM646X_MCASP1TXINT,
+		.flags	= IORESOURCE_IRQ,
 	},
 };
 
diff --git a/arch/arm/mach-davinci/include/mach/irqs.h b/arch/arm/mach-davinci/include/mach/irqs.h
index 354af71..edb2ca6 100644
--- a/arch/arm/mach-davinci/include/mach/irqs.h
+++ b/arch/arm/mach-davinci/include/mach/irqs.h
@@ -129,8 +129,8 @@
 #define IRQ_DM646X_EMACMISCINT  27
 #define IRQ_DM646X_MCASP0TXINT  28
 #define IRQ_DM646X_MCASP0RXINT  29
+#define IRQ_DM646X_MCASP1TXINT  30
 #define IRQ_DM646X_RESERVED_3   31
-#define IRQ_DM646X_MCASP1TXINT  32
 #define IRQ_DM646X_VLQINT       38
 #define IRQ_DM646X_UARTINT2     42
 #define IRQ_DM646X_SPINT0       43
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index c8dffce..0748747 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -77,13 +77,6 @@
 	select IMX_HAVE_IOMUX_V1
 	select MXC_AVIC
 
-config SOC_IMX25
-	bool
-	select ARCH_MXC_IOMUX_V3
-	select CPU_ARM926T
-	select MXC_AVIC
-	select PINCTRL_IMX25
-
 config SOC_IMX27
 	bool
 	select CPU_ARM926T
@@ -149,62 +142,6 @@
 	  Include support for MX21ADS platform. This includes specific
 	  configurations for the board and its peripherals.
 
-comment "MX25 platforms:"
-
-config MACH_MX25_3DS
-	bool "Support MX25PDK (3DS) Platform"
-	select IMX_HAVE_PLATFORM_FLEXCAN
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMXDI_RTC
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_KEYPAD
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	select SOC_IMX25
-
-config MACH_EUKREA_CPUIMX25SD
-	bool "Support Eukrea CPUIMX25 Platform"
-	select IMX_HAVE_PLATFORM_FLEXCAN
-	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMXDI_RTC
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX25
-
-choice
-	prompt "Baseboard"
-	depends on MACH_EUKREA_CPUIMX25SD
-	default MACH_EUKREA_MBIMXSD25_BASEBOARD
-
-config MACH_EUKREA_MBIMXSD25_BASEBOARD
-	bool "Eukrea MBIMXSD development board"
-	select IMX_HAVE_PLATFORM_GPIO_KEYS
-	select IMX_HAVE_PLATFORM_IMX_SSI
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select LEDS_GPIO_REGISTER
-	help
-	  This adds board specific devices that can be found on Eukrea's
-	  MBIMXSD evaluation board.
-
-endchoice
-
-config MACH_IMX25_DT
-	bool "Support i.MX25 platforms from device tree"
-	select SOC_IMX25
-	help
-	  Include support for Freescale i.MX25 based platforms
-	  using the device tree for discovery
-
 comment "MX27 platforms:"
 
 config MACH_MX27ADS
@@ -557,6 +494,20 @@
 
 endif
 
+if ARCH_MULTI_V5
+
+comment "Device tree only"
+
+config SOC_IMX25
+	bool "i.MX25 support"
+	select ARCH_MXC_IOMUX_V3
+	select CPU_ARM926T
+	select MXC_AVIC
+	select PINCTRL_IMX25
+	help
+	  This enables support for Freescale i.MX25 processor
+endif
+
 if ARCH_MULTI_V7
 
 comment "Device tree only"
@@ -637,7 +588,7 @@
 	select PL310_ERRATA_769419 if CACHE_L2X0
 
 	help
-	  This enable support for Freescale Vybrid VF610 processor.
+	  This enables support for Freescale Vybrid VF610 processor.
 
 choice
 	prompt "Clocksource for scheduler clock"
@@ -667,7 +618,7 @@
 	select ZONE_DMA if ARM_LPAE
 
 	help
-	  This enable support for Freescale LS1021A processor.
+	  This enables support for Freescale LS1021A processor.
 
 endif
 
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 8d1b101..3244cf1 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -3,7 +3,7 @@
 obj-$(CONFIG_SOC_IMX1) += clk-imx1.o mm-imx1.o
 obj-$(CONFIG_SOC_IMX21) += clk-imx21.o mm-imx21.o
 
-obj-$(CONFIG_SOC_IMX25) += clk-imx25.o mm-imx25.o ehci-imx25.o cpu-imx25.o
+obj-$(CONFIG_SOC_IMX25) += clk-imx25.o cpu-imx25.o mach-imx25.o
 
 obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
 obj-$(CONFIG_SOC_IMX27) += clk-imx27.o mm-imx27.o ehci-imx27.o
@@ -48,12 +48,6 @@
 # i.MX21 based machines
 obj-$(CONFIG_MACH_MX21ADS) += mach-mx21ads.o
 
-# i.MX25 based machines
-obj-$(CONFIG_MACH_MX25_3DS) += mach-mx25_3ds.o
-obj-$(CONFIG_MACH_EUKREA_CPUIMX25SD) += mach-eukrea_cpuimx25.o
-obj-$(CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD) += eukrea_mbimxsd25-baseboard.o
-obj-$(CONFIG_MACH_IMX25_DT) += imx25-dt.o
-
 # i.MX27 based machines
 obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
 obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
diff --git a/arch/arm/mach-imx/clk-imx25.c b/arch/arm/mach-imx/clk-imx25.c
index 59c0c85..9c2633a 100644
--- a/arch/arm/mach-imx/clk-imx25.c
+++ b/arch/arm/mach-imx/clk-imx25.c
@@ -30,7 +30,6 @@
 #include "clk.h"
 #include "common.h"
 #include "hardware.h"
-#include "mx25.h"
 
 #define CCM_MPCTL	0x00
 #define CCM_UPCTL	0x04
@@ -239,80 +238,6 @@
 	return 0;
 }
 
-int __init mx25_clocks_init(void)
-{
-	void __iomem *ccm;
-
-	ccm = ioremap(MX25_CRM_BASE_ADDR, SZ_16K);
-
-	__mx25_clocks_init(24000000, ccm);
-
-	clk_register_clkdev(clk[gpt1_ipg], "ipg", "imx-gpt.0");
-	clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0");
-	/* i.mx25 has the i.mx21 type uart */
-	clk_register_clkdev(clk[uart1_ipg], "ipg", "imx21-uart.0");
-	clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.0");
-	clk_register_clkdev(clk[uart2_ipg], "ipg", "imx21-uart.1");
-	clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.1");
-	clk_register_clkdev(clk[uart3_ipg], "ipg", "imx21-uart.2");
-	clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.2");
-	clk_register_clkdev(clk[uart4_ipg], "ipg", "imx21-uart.3");
-	clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.3");
-	clk_register_clkdev(clk[uart5_ipg], "ipg", "imx21-uart.4");
-	clk_register_clkdev(clk[uart_ipg_per], "per", "imx21-uart.4");
-	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.0");
-	clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.0");
-	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0");
-	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.1");
-	clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.1");
-	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.1");
-	clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2");
-	clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.2");
-	clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2");
-	clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27");
-	clk_register_clkdev(clk[usbotg_ahb], "ahb", "imx-udc-mx27");
-	clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27");
-	clk_register_clkdev(clk[nfc_ipg_per], NULL, "imx25-nand.0");
-	/* i.mx25 has the i.mx35 type cspi */
-	clk_register_clkdev(clk[cspi1_ipg], NULL, "imx35-cspi.0");
-	clk_register_clkdev(clk[cspi2_ipg], NULL, "imx35-cspi.1");
-	clk_register_clkdev(clk[cspi3_ipg], NULL, "imx35-cspi.2");
-	clk_register_clkdev(clk[kpp_ipg], NULL, "imx-keypad");
-	clk_register_clkdev(clk[tsc_ipg], NULL, "mx25-adc");
-	clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.0");
-	clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.1");
-	clk_register_clkdev(clk[i2c_ipg_per], NULL, "imx21-i2c.2");
-	clk_register_clkdev(clk[fec_ipg], "ipg", "imx25-fec.0");
-	clk_register_clkdev(clk[fec_ahb], "ahb", "imx25-fec.0");
-	clk_register_clkdev(clk[dryice_ipg], NULL, "imxdi_rtc.0");
-	clk_register_clkdev(clk[lcdc_ipg_per], "per", "imx21-fb.0");
-	clk_register_clkdev(clk[lcdc_ipg], "ipg", "imx21-fb.0");
-	clk_register_clkdev(clk[lcdc_ahb], "ahb", "imx21-fb.0");
-	clk_register_clkdev(clk[wdt_ipg], NULL, "imx2-wdt.0");
-	clk_register_clkdev(clk[ssi1_ipg], NULL, "imx-ssi.0");
-	clk_register_clkdev(clk[ssi2_ipg], NULL, "imx-ssi.1");
-	clk_register_clkdev(clk[esdhc1_ipg_per], "per", "sdhci-esdhc-imx25.0");
-	clk_register_clkdev(clk[esdhc1_ipg], "ipg", "sdhci-esdhc-imx25.0");
-	clk_register_clkdev(clk[esdhc1_ahb], "ahb", "sdhci-esdhc-imx25.0");
-	clk_register_clkdev(clk[esdhc2_ipg_per], "per", "sdhci-esdhc-imx25.1");
-	clk_register_clkdev(clk[esdhc2_ipg], "ipg", "sdhci-esdhc-imx25.1");
-	clk_register_clkdev(clk[esdhc2_ahb], "ahb", "sdhci-esdhc-imx25.1");
-	clk_register_clkdev(clk[csi_ipg_per], "per", "imx25-camera.0");
-	clk_register_clkdev(clk[csi_ipg], "ipg", "imx25-camera.0");
-	clk_register_clkdev(clk[csi_ahb], "ahb", "imx25-camera.0");
-	clk_register_clkdev(clk[dummy], "audmux", NULL);
-	clk_register_clkdev(clk[can1_ipg], NULL, "flexcan.0");
-	clk_register_clkdev(clk[can2_ipg], NULL, "flexcan.1");
-	/* i.mx25 has the i.mx35 type sdma */
-	clk_register_clkdev(clk[sdma_ipg], "ipg", "imx35-sdma");
-	clk_register_clkdev(clk[sdma_ahb], "ahb", "imx35-sdma");
-	clk_register_clkdev(clk[iim_ipg], "iim", NULL);
-
-	mxc_timer_init(MX25_IO_ADDRESS(MX25_GPT1_BASE_ADDR), MX25_INT_GPT1);
-
-	return 0;
-}
-
 static void __init mx25_clocks_init_dt(struct device_node *np)
 {
 	struct device_node *refnp;
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 1028b6c..771ecfe 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -23,13 +23,11 @@
 
 void mx1_map_io(void);
 void mx21_map_io(void);
-void mx25_map_io(void);
 void mx27_map_io(void);
 void mx31_map_io(void);
 void mx35_map_io(void);
 void imx1_init_early(void);
 void imx21_init_early(void);
-void imx25_init_early(void);
 void imx27_init_early(void);
 void imx31_init_early(void);
 void imx35_init_early(void);
@@ -37,13 +35,11 @@
 void tzic_init_irq(void);
 void mx1_init_irq(void);
 void mx21_init_irq(void);
-void mx25_init_irq(void);
 void mx27_init_irq(void);
 void mx31_init_irq(void);
 void mx35_init_irq(void);
 void imx1_soc_init(void);
 void imx21_soc_init(void);
-void imx25_soc_init(void);
 void imx27_soc_init(void);
 void imx31_soc_init(void);
 void imx35_soc_init(void);
@@ -51,7 +47,6 @@
 void mxc_timer_init(void __iomem *, int);
 int mx1_clocks_init(unsigned long fref);
 int mx21_clocks_init(unsigned long lref, unsigned long fref);
-int mx25_clocks_init(void);
 int mx27_clocks_init(unsigned long fref);
 int mx31_clocks_init(unsigned long fref);
 int mx35_clocks_init(void);
diff --git a/arch/arm/mach-imx/cpu-imx25.c b/arch/arm/mach-imx/cpu-imx25.c
index 96ec64b..d0ad67e 100644
--- a/arch/arm/mach-imx/cpu-imx25.c
+++ b/arch/arm/mach-imx/cpu-imx25.c
@@ -11,6 +11,8 @@
  */
 #include <linux/module.h>
 #include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
 
 #include "iim.h"
 #include "hardware.h"
@@ -20,8 +22,15 @@
 static int mx25_read_cpu_rev(void)
 {
 	u32 rev;
+	void __iomem *iim_base;
+	struct device_node *np;
 
-	rev = __raw_readl(MX25_IO_ADDRESS(MX25_IIM_BASE_ADDR + MXC_IIMSREV));
+	np = of_find_compatible_node(NULL, NULL, "fsl,imx25-iim");
+	iim_base = of_iomap(np, 0);
+	BUG_ON(!iim_base);
+	rev = readl(iim_base + MXC_IIMSREV);
+	iounmap(iim_base);
+
 	switch (rev) {
 	case 0x00:
 		return IMX_CHIP_REVISION_1_0;
diff --git a/arch/arm/mach-imx/devices-imx25.h b/arch/arm/mach-imx/devices-imx25.h
deleted file mode 100644
index 61a114c..0000000
--- a/arch/arm/mach-imx/devices-imx25.h
+++ /dev/null
@@ -1,85 +0,0 @@
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or modify it under
- * the terms of the GNU General Public License version 2 as published by the
- * Free Software Foundation.
- */
-#include "devices/devices-common.h"
-
-extern const struct imx_fec_data imx25_fec_data;
-#define imx25_add_fec(pdata)	\
-	imx_add_fec(&imx25_fec_data, pdata)
-
-extern const struct imx_flexcan_data imx25_flexcan_data[];
-#define imx25_add_flexcan(id)	\
-	imx_add_flexcan(&imx25_flexcan_data[id])
-#define imx25_add_flexcan0()		imx25_add_flexcan(0)
-#define imx25_add_flexcan1()		imx25_add_flexcan(1)
-
-extern const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data;
-#define imx25_add_fsl_usb2_udc(pdata)	\
-	imx_add_fsl_usb2_udc(&imx25_fsl_usb2_udc_data, pdata)
-
-extern struct imx_imxdi_rtc_data imx25_imxdi_rtc_data;
-#define imx25_add_imxdi_rtc()	\
-	imx_add_imxdi_rtc(&imx25_imxdi_rtc_data)
-
-extern const struct imx_imx2_wdt_data imx25_imx2_wdt_data;
-#define imx25_add_imx2_wdt()	\
-	imx_add_imx2_wdt(&imx25_imx2_wdt_data)
-
-extern const struct imx_imx_fb_data imx25_imx_fb_data;
-#define imx25_add_imx_fb(pdata)	\
-	imx_add_imx_fb(&imx25_imx_fb_data, pdata)
-
-extern const struct imx_imx_i2c_data imx25_imx_i2c_data[];
-#define imx25_add_imx_i2c(id, pdata)	\
-	imx_add_imx_i2c(&imx25_imx_i2c_data[id], pdata)
-#define imx25_add_imx_i2c0(pdata)	imx25_add_imx_i2c(0, pdata)
-#define imx25_add_imx_i2c1(pdata)	imx25_add_imx_i2c(1, pdata)
-#define imx25_add_imx_i2c2(pdata)	imx25_add_imx_i2c(2, pdata)
-
-extern const struct imx_imx_keypad_data imx25_imx_keypad_data;
-#define imx25_add_imx_keypad(pdata)	\
-	imx_add_imx_keypad(&imx25_imx_keypad_data, pdata)
-
-extern const struct imx_imx_ssi_data imx25_imx_ssi_data[];
-#define imx25_add_imx_ssi(id, pdata)	\
-	imx_add_imx_ssi(&imx25_imx_ssi_data[id], pdata)
-
-extern const struct imx_imx_uart_1irq_data imx25_imx_uart_data[];
-#define imx25_add_imx_uart(id, pdata)	\
-	imx_add_imx_uart_1irq(&imx25_imx_uart_data[id], pdata)
-#define imx25_add_imx_uart0(pdata)	imx25_add_imx_uart(0, pdata)
-#define imx25_add_imx_uart1(pdata)	imx25_add_imx_uart(1, pdata)
-#define imx25_add_imx_uart2(pdata)	imx25_add_imx_uart(2, pdata)
-#define imx25_add_imx_uart3(pdata)	imx25_add_imx_uart(3, pdata)
-#define imx25_add_imx_uart4(pdata)	imx25_add_imx_uart(4, pdata)
-
-extern const struct imx_mx2_camera_data imx25_mx2_camera_data;
-#define imx25_add_mx2_camera(pdata)	\
-	imx_add_mx2_camera(&imx25_mx2_camera_data, pdata)
-
-extern const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data;
-#define imx25_add_mxc_ehci_otg(pdata)	\
-	imx_add_mxc_ehci(&imx25_mxc_ehci_otg_data, pdata)
-extern const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data;
-#define imx25_add_mxc_ehci_hs(pdata)	\
-	imx_add_mxc_ehci(&imx25_mxc_ehci_hs_data, pdata)
-
-extern const struct imx_mxc_nand_data imx25_mxc_nand_data;
-#define imx25_add_mxc_nand(pdata)	\
-	imx_add_mxc_nand(&imx25_mxc_nand_data, pdata)
-
-extern const struct imx_sdhci_esdhc_imx_data imx25_sdhci_esdhc_imx_data[];
-#define imx25_add_sdhci_esdhc_imx(id, pdata)	\
-	imx_add_sdhci_esdhc_imx(&imx25_sdhci_esdhc_imx_data[id], pdata)
-
-extern const struct imx_spi_imx_data imx25_cspi_data[];
-#define imx25_add_spi_imx(id, pdata)	\
-	imx_add_spi_imx(&imx25_cspi_data[id], pdata)
-#define imx25_add_spi_imx0(pdata)	imx25_add_spi_imx(0, pdata)
-#define imx25_add_spi_imx1(pdata)	imx25_add_spi_imx(1, pdata)
-#define imx25_add_spi_imx2(pdata)	imx25_add_spi_imx(2, pdata)
diff --git a/arch/arm/mach-imx/devices/Kconfig b/arch/arm/mach-imx/devices/Kconfig
index 1d2cc18..3a55298 100644
--- a/arch/arm/mach-imx/devices/Kconfig
+++ b/arch/arm/mach-imx/devices/Kconfig
@@ -21,9 +21,6 @@
 config IMX_HAVE_PLATFORM_IMX2_WDT
 	bool
 
-config IMX_HAVE_PLATFORM_IMXDI_RTC
-	bool
-
 config IMX_HAVE_PLATFORM_IMX_FB
 	bool
 
diff --git a/arch/arm/mach-imx/devices/Makefile b/arch/arm/mach-imx/devices/Makefile
index 8fdb12b..e5cf587 100644
--- a/arch/arm/mach-imx/devices/Makefile
+++ b/arch/arm/mach-imx/devices/Makefile
@@ -8,7 +8,6 @@
 obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX21_HCD) += platform-imx21-hcd.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX27_CODA) += platform-imx27-coda.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX2_WDT) += platform-imx2-wdt.o
-obj-$(CONFIG_IMX_HAVE_PLATFORM_IMXDI_RTC) += platform-imxdi_rtc.o
 obj-y += platform-imx-dma.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_FB) += platform-imx-fb.o
 obj-$(CONFIG_IMX_HAVE_PLATFORM_IMX_I2C) += platform-imx-i2c.o
diff --git a/arch/arm/mach-imx/devices/platform-fec.c b/arch/arm/mach-imx/devices/platform-fec.c
index d86f925..b403a4f 100644
--- a/arch/arm/mach-imx/devices/platform-fec.c
+++ b/arch/arm/mach-imx/devices/platform-fec.c
@@ -19,11 +19,6 @@
 		.irq = soc ## _INT_FEC,					\
 	}
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_fec_data imx25_fec_data __initconst =
-	imx_fec_data_entry_single(MX25, "imx25-fec");
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_fec_data imx27_fec_data __initconst =
 	imx_fec_data_entry_single(MX27, "imx27-fec");
diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
index 23b0061..25e1de6 100644
--- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
+++ b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c
@@ -18,11 +18,6 @@
 		.irq = soc ## _INT_USB_OTG,				\
 	}
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data __initconst =
-	imx_fsl_usb2_udc_data_entry_single(MX25, "imx-udc-mx27");
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst =
 	imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27");
diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c
index 25a47c6..7df6328 100644
--- a/arch/arm/mach-imx/devices/platform-imx-fb.c
+++ b/arch/arm/mach-imx/devices/platform-imx-fb.c
@@ -29,11 +29,6 @@
 	imx_imx_fb_data_entry_single(MX21, "imx21-fb", SZ_4K);
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx_fb_data imx25_imx_fb_data __initconst =
-	imx_imx_fb_data_entry_single(MX25, "imx21-fb", SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx_fb_data imx27_imx_fb_data __initconst =
 	imx_imx_fb_data_entry_single(MX27, "imx21-fb", SZ_4K);
diff --git a/arch/arm/mach-imx/devices/platform-imx-i2c.c b/arch/arm/mach-imx/devices/platform-imx-i2c.c
index 644ac26..ae97915 100644
--- a/arch/arm/mach-imx/devices/platform-imx-i2c.c
+++ b/arch/arm/mach-imx/devices/platform-imx-i2c.c
@@ -31,16 +31,6 @@
 	imx_imx_i2c_data_entry_single(MX21, "imx21-i2c", 0, , SZ_4K);
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx_i2c_data imx25_imx_i2c_data[] __initconst = {
-#define imx25_imx_i2c_data_entry(_id, _hwid)				\
-	imx_imx_i2c_data_entry(MX25, "imx21-i2c", _id, _hwid, SZ_16K)
-	imx25_imx_i2c_data_entry(0, 1),
-	imx25_imx_i2c_data_entry(1, 2),
-	imx25_imx_i2c_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx_i2c_data imx27_imx_i2c_data[] __initconst = {
 #define imx27_imx_i2c_data_entry(_id, _hwid)				\
diff --git a/arch/arm/mach-imx/devices/platform-imx-keypad.c b/arch/arm/mach-imx/devices/platform-imx-keypad.c
index f42200b..479e4d7 100644
--- a/arch/arm/mach-imx/devices/platform-imx-keypad.c
+++ b/arch/arm/mach-imx/devices/platform-imx-keypad.c
@@ -21,11 +21,6 @@
 	imx_imx_keypad_data_entry_single(MX21, SZ_16);
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx_keypad_data imx25_imx_keypad_data __initconst =
-	imx_imx_keypad_data_entry_single(MX25, SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx_keypad_data imx27_imx_keypad_data __initconst =
 	imx_imx_keypad_data_entry_single(MX27, SZ_16);
diff --git a/arch/arm/mach-imx/devices/platform-imx-ssi.c b/arch/arm/mach-imx/devices/platform-imx-ssi.c
index 1c7c721..6f0e94e 100644
--- a/arch/arm/mach-imx/devices/platform-imx-ssi.c
+++ b/arch/arm/mach-imx/devices/platform-imx-ssi.c
@@ -30,15 +30,6 @@
 };
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx_ssi_data imx25_imx_ssi_data[] __initconst = {
-#define imx25_imx_ssi_data_entry(_id, _hwid)				\
-	imx_imx_ssi_data_entry(MX25, _id, _hwid, SZ_4K)
-	imx25_imx_ssi_data_entry(0, 1),
-	imx25_imx_ssi_data_entry(1, 2),
-};
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx_ssi_data imx27_imx_ssi_data[] __initconst = {
 #define imx27_imx_ssi_data_entry(_id, _hwid)				\
diff --git a/arch/arm/mach-imx/devices/platform-imx-uart.c b/arch/arm/mach-imx/devices/platform-imx-uart.c
index 8c01836..6962cff 100644
--- a/arch/arm/mach-imx/devices/platform-imx-uart.c
+++ b/arch/arm/mach-imx/devices/platform-imx-uart.c
@@ -47,18 +47,6 @@
 };
 #endif
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx_uart_1irq_data imx25_imx_uart_data[] __initconst = {
-#define imx25_imx_uart_data_entry(_id, _hwid)				\
-	imx_imx_uart_1irq_data_entry(MX25, _id, _hwid, SZ_16K)
-	imx25_imx_uart_data_entry(0, 1),
-	imx25_imx_uart_data_entry(1, 2),
-	imx25_imx_uart_data_entry(2, 3),
-	imx25_imx_uart_data_entry(3, 4),
-	imx25_imx_uart_data_entry(4, 5),
-};
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx_uart_1irq_data imx27_imx_uart_data[] __initconst = {
 #define imx27_imx_uart_data_entry(_id, _hwid)				\
diff --git a/arch/arm/mach-imx/devices/platform-imx2-wdt.c b/arch/arm/mach-imx/devices/platform-imx2-wdt.c
index 54f63bc..8c134c8 100644
--- a/arch/arm/mach-imx/devices/platform-imx2-wdt.c
+++ b/arch/arm/mach-imx/devices/platform-imx2-wdt.c
@@ -25,11 +25,6 @@
 	imx_imx2_wdt_data_entry_single(MX21, 0, , SZ_4K);
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imx2_wdt_data imx25_imx2_wdt_data __initconst =
-	imx_imx2_wdt_data_entry_single(MX25, 0, , SZ_16K);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_imx2_wdt_data imx27_imx2_wdt_data __initconst =
 	imx_imx2_wdt_data_entry_single(MX27, 0, , SZ_4K);
diff --git a/arch/arm/mach-imx/devices/platform-imxdi_rtc.c b/arch/arm/mach-imx/devices/platform-imxdi_rtc.c
deleted file mode 100644
index 5bb490d..0000000
--- a/arch/arm/mach-imx/devices/platform-imxdi_rtc.c
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
- * Copyright (C) 2010 Pengutronix
- * Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or modify it under
- * the terms of the GNU General Public License version 2 as published by the
- * Free Software Foundation.
- */
-#include <asm/sizes.h>
-
-#include "../hardware.h"
-#include "devices-common.h"
-
-#define imx_imxdi_rtc_data_entry_single(soc)				\
-	{								\
-		.iobase = soc ## _DRYICE_BASE_ADDR,			\
-		.irq = soc ## _INT_DRYICE,				\
-	}
-
-#ifdef CONFIG_SOC_IMX25
-const struct imx_imxdi_rtc_data imx25_imxdi_rtc_data __initconst =
-	imx_imxdi_rtc_data_entry_single(MX25);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
-struct platform_device *__init imx_add_imxdi_rtc(
-		const struct imx_imxdi_rtc_data *data)
-{
-	struct resource res[] = {
-		{
-			.start = data->iobase,
-			.end = data->iobase + SZ_16K - 1,
-			.flags = IORESOURCE_MEM,
-		}, {
-			.start = data->irq,
-			.end = data->irq,
-			.flags = IORESOURCE_IRQ,
-		},
-	};
-
-	return imx_add_platform_device("imxdi_rtc", 0,
-			res, ARRAY_SIZE(res), NULL, 0);
-}
diff --git a/arch/arm/mach-imx/devices/platform-mx2-camera.c b/arch/arm/mach-imx/devices/platform-mx2-camera.c
index b53e1f3..4c377c3 100644
--- a/arch/arm/mach-imx/devices/platform-mx2-camera.c
+++ b/arch/arm/mach-imx/devices/platform-mx2-camera.c
@@ -27,11 +27,6 @@
 		.irqemmaprp = soc ## _INT_EMMAPRP,			\
 	}
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_mx2_camera_data imx25_mx2_camera_data __initconst =
-	imx_mx2_camera_data_entry_single(MX25, "imx25-camera");
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_mx2_camera_data imx27_mx2_camera_data __initconst =
 	imx_mx2_camera_data_entry_single_emma(MX27, "imx27-camera");
diff --git a/arch/arm/mach-imx/devices/platform-mxc-ehci.c b/arch/arm/mach-imx/devices/platform-mxc-ehci.c
index 2963536..4537abd 100644
--- a/arch/arm/mach-imx/devices/platform-mxc-ehci.c
+++ b/arch/arm/mach-imx/devices/platform-mxc-ehci.c
@@ -18,13 +18,6 @@
 		.irq = soc ## _INT_USB_ ## hs,				\
 	}
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_mxc_ehci_data imx25_mxc_ehci_otg_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX25, 0, OTG);
-const struct imx_mxc_ehci_data imx25_mxc_ehci_hs_data __initconst =
-	imx_mxc_ehci_data_entry_single(MX25, 1, HS);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_mxc_ehci_data imx27_mxc_ehci_otg_data __initconst =
 	imx_mxc_ehci_data_entry_single(MX27, 0, OTG);
diff --git a/arch/arm/mach-imx/devices/platform-mxc_nand.c b/arch/arm/mach-imx/devices/platform-mxc_nand.c
index fa618a3..676df49 100644
--- a/arch/arm/mach-imx/devices/platform-mxc_nand.c
+++ b/arch/arm/mach-imx/devices/platform-mxc_nand.c
@@ -34,11 +34,6 @@
 	imx_mxc_nand_data_entry_single(MX21, "imx21-nand", SZ_4K);
 #endif /* ifdef CONFIG_SOC_IMX21 */
 
-#ifdef CONFIG_SOC_IMX25
-const struct imx_mxc_nand_data imx25_mxc_nand_data __initconst =
-	imx_mxc_nand_data_entry_single(MX25, "imx25-nand", SZ_8K);
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_mxc_nand_data imx27_mxc_nand_data __initconst =
 	imx_mxc_nand_data_entry_single(MX27, "imx27-nand", SZ_4K);
diff --git a/arch/arm/mach-imx/devices/platform-spi_imx.c b/arch/arm/mach-imx/devices/platform-spi_imx.c
index aca825d..5e9707b 100644
--- a/arch/arm/mach-imx/devices/platform-spi_imx.c
+++ b/arch/arm/mach-imx/devices/platform-spi_imx.c
@@ -39,17 +39,6 @@
 };
 #endif
 
-#ifdef CONFIG_SOC_IMX25
-/* i.mx25 has the i.mx35 type cspi */
-const struct imx_spi_imx_data imx25_cspi_data[] __initconst = {
-#define imx25_cspi_data_entry(_id, _hwid)				\
-	imx_spi_imx_data_entry(MX25, CSPI, "imx35-cspi", _id, _hwid, SZ_16K)
-	imx25_cspi_data_entry(0, 1),
-	imx25_cspi_data_entry(1, 2),
-	imx25_cspi_data_entry(2, 3),
-};
-#endif /* ifdef CONFIG_SOC_IMX25 */
-
 #ifdef CONFIG_SOC_IMX27
 const struct imx_spi_imx_data imx27_cspi_data[] __initconst = {
 #define imx27_cspi_data_entry(_id, _hwid)				\
diff --git a/arch/arm/mach-imx/ehci-imx25.c b/arch/arm/mach-imx/ehci-imx25.c
deleted file mode 100644
index 42a5a3d..0000000
--- a/arch/arm/mach-imx/ehci-imx25.c
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
- * Copyright (C) 2010 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
- * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- * for more details.
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/platform_data/usb-ehci-mxc.h>
-
-#include "ehci.h"
-#include "hardware.h"
-
-#define USBCTRL_OTGBASE_OFFSET	0x600
-
-#define MX25_OTG_SIC_SHIFT	29
-#define MX25_OTG_SIC_MASK	(0x3 << MX25_OTG_SIC_SHIFT)
-#define MX25_OTG_PM_BIT		(1 << 24)
-#define MX25_OTG_PP_BIT		(1 << 11)
-#define MX25_OTG_OCPOL_BIT	(1 << 3)
-
-#define MX25_H1_SIC_SHIFT	21
-#define MX25_H1_SIC_MASK	(0x3 << MX25_H1_SIC_SHIFT)
-#define MX25_H1_PP_BIT		(1 << 18)
-#define MX25_H1_PM_BIT		(1 << 16)
-#define MX25_H1_IPPUE_UP_BIT	(1 << 7)
-#define MX25_H1_IPPUE_DOWN_BIT	(1 << 6)
-#define MX25_H1_TLL_BIT		(1 << 5)
-#define MX25_H1_USBTE_BIT	(1 << 4)
-#define MX25_H1_OCPOL_BIT	(1 << 2)
-
-int mx25_initialize_usb_hw(int port, unsigned int flags)
-{
-	unsigned int v;
-
-	v = readl(MX25_IO_ADDRESS(MX25_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	switch (port) {
-	case 0:	/* OTG port */
-		v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT |
-			MX25_OTG_OCPOL_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX25_OTG_PM_BIT;
-
-		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
-			v |= MX25_OTG_PP_BIT;
-
-		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
-			v |= MX25_OTG_OCPOL_BIT;
-
-		break;
-	case 1: /* H1 port */
-		v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT |
-			MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | MX25_H1_USBTE_BIT |
-			MX25_H1_IPPUE_DOWN_BIT | MX25_H1_IPPUE_UP_BIT);
-		v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT;
-
-		if (!(flags & MXC_EHCI_POWER_PINS_ENABLED))
-			v |= MX25_H1_PM_BIT;
-
-		if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH)
-			v |= MX25_H1_PP_BIT;
-
-		if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW))
-			v |= MX25_H1_OCPOL_BIT;
-
-		if (!(flags & MXC_EHCI_TTL_ENABLED))
-			v |= MX25_H1_TLL_BIT;
-
-		if (flags & MXC_EHCI_INTERNAL_PHY)
-			v |= MX25_H1_USBTE_BIT;
-
-		if (flags & MXC_EHCI_IPPUE_DOWN)
-			v |= MX25_H1_IPPUE_DOWN_BIT;
-
-		if (flags & MXC_EHCI_IPPUE_UP)
-			v |= MX25_H1_IPPUE_UP_BIT;
-
-		break;
-	default:
-		return -EINVAL;
-	}
-
-	writel(v, MX25_IO_ADDRESS(MX25_USB_BASE_ADDR + USBCTRL_OTGBASE_OFFSET));
-
-	return 0;
-}
-
diff --git a/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c b/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c
deleted file mode 100644
index e77cc3af..0000000
--- a/arch/arm/mach-imx/eukrea_mbimxsd25-baseboard.c
+++ /dev/null
@@ -1,310 +0,0 @@
-/*
- * Copyright (C) 2010 Eric Benard - eric@eukrea.com
- *
- * Based on pcm970-baseboard.c which is :
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/spi/spi.h>
-#include <video/platform_lcd.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx25.h"
-#include "hardware.h"
-#include "iomux-mx25.h"
-#include "mx25.h"
-
-static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
-	/* LCD */
-	MX25_PAD_LD0__LD0,
-	MX25_PAD_LD1__LD1,
-	MX25_PAD_LD2__LD2,
-	MX25_PAD_LD3__LD3,
-	MX25_PAD_LD4__LD4,
-	MX25_PAD_LD5__LD5,
-	MX25_PAD_LD6__LD6,
-	MX25_PAD_LD7__LD7,
-	MX25_PAD_LD8__LD8,
-	MX25_PAD_LD9__LD9,
-	MX25_PAD_LD10__LD10,
-	MX25_PAD_LD11__LD11,
-	MX25_PAD_LD12__LD12,
-	MX25_PAD_LD13__LD13,
-	MX25_PAD_LD14__LD14,
-	MX25_PAD_LD15__LD15,
-	MX25_PAD_GPIO_E__LD16,
-	MX25_PAD_GPIO_F__LD17,
-	MX25_PAD_HSYNC__HSYNC,
-	MX25_PAD_VSYNC__VSYNC,
-	MX25_PAD_LSCLK__LSCLK,
-	MX25_PAD_OE_ACD__OE_ACD,
-	MX25_PAD_CONTRAST__CONTRAST,
-	/* LCD_PWR */
-	MX25_PAD_PWM__GPIO_1_26,
-	/* LED */
-	MX25_PAD_POWER_FAIL__GPIO_3_19,
-	/* SWITCH */
-	MX25_PAD_VSTBY_ACK__GPIO_3_18,
-	/* UART2 */
-	MX25_PAD_UART2_RTS__UART2_RTS,
-	MX25_PAD_UART2_CTS__UART2_CTS,
-	MX25_PAD_UART2_TXD__UART2_TXD,
-	MX25_PAD_UART2_RXD__UART2_RXD,
-	/* SD1 */
-	MX25_PAD_SD1_CMD__SD1_CMD,
-	MX25_PAD_SD1_CLK__SD1_CLK,
-	MX25_PAD_SD1_DATA0__SD1_DATA0,
-	MX25_PAD_SD1_DATA1__SD1_DATA1,
-	MX25_PAD_SD1_DATA2__SD1_DATA2,
-	MX25_PAD_SD1_DATA3__SD1_DATA3,
-	/* SD1 CD */
-	MX25_PAD_DE_B__GPIO_2_20,
-	/* I2S */
-	MX25_PAD_KPP_COL3__AUD5_TXFS,
-	MX25_PAD_KPP_COL2__AUD5_TXC,
-	MX25_PAD_KPP_COL1__AUD5_RXD,
-	MX25_PAD_KPP_COL0__AUD5_TXD,
-	/* CAN */
-	MX25_PAD_GPIO_D__CAN2_RX,
-	MX25_PAD_GPIO_C__CAN2_TX,
-	/* SPI1 */
-	MX25_PAD_CSPI1_MOSI__CSPI1_MOSI,
-	MX25_PAD_CSPI1_MISO__CSPI1_MISO,
-	MX25_PAD_CSPI1_SS0__GPIO_1_16,
-	MX25_PAD_CSPI1_SS1__GPIO_1_17,
-	MX25_PAD_CSPI1_SCLK__CSPI1_SCLK,
-	MX25_PAD_CSPI1_RDY__GPIO_2_22,
-};
-
-#define GPIO_LED1		IMX_GPIO_NR(3, 19)
-#define GPIO_SWITCH1	IMX_GPIO_NR(3, 18)
-#define GPIO_SD1CD		IMX_GPIO_NR(2, 20)
-#define GPIO_LCDPWR		IMX_GPIO_NR(1, 26)
-#define	GPIO_SPI1_SS0	IMX_GPIO_NR(1, 16)
-#define	GPIO_SPI1_SS1	IMX_GPIO_NR(1, 17)
-#define	GPIO_SPI1_IRQ	IMX_GPIO_NR(2, 22)
-
-static struct imx_fb_videomode eukrea_mximxsd_modes[] = {
-	{
-		.mode	= {
-			.name		= "CMO-QVGA",
-			.refresh	= 60,
-			.xres		= 320,
-			.yres		= 240,
-			.pixclock	= KHZ2PICOS(6500),
-			.left_margin	= 30,
-			.right_margin	= 38,
-			.upper_margin	= 20,
-			.lower_margin	= 3,
-			.hsync_len	= 15,
-			.vsync_len	= 4,
-		},
-		.bpp	= 16,
-		.pcr	= 0xCAD08B80,
-	}, {
-		.mode = {
-			.name		= "DVI-VGA",
-			.refresh	= 60,
-			.xres		= 640,
-			.yres		= 480,
-			.pixclock	= 32000,
-			.hsync_len	= 7,
-			.left_margin	= 100,
-			.right_margin	= 100,
-			.vsync_len	= 7,
-			.upper_margin	= 7,
-			.lower_margin	= 100,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "DVI-SVGA",
-			.refresh	= 60,
-			.xres		= 800,
-			.yres		= 600,
-			.pixclock	= 25000,
-			.hsync_len	= 7,
-			.left_margin	= 75,
-			.right_margin	= 75,
-			.vsync_len	= 7,
-			.upper_margin	= 7,
-			.lower_margin	= 75,
-		},
-		.pcr		= 0xFA208B80,
-		.bpp		= 16,
-	},
-};
-
-static const struct imx_fb_platform_data eukrea_mximxsd_fb_pdata __initconst = {
-	.mode		= eukrea_mximxsd_modes,
-	.num_modes	= ARRAY_SIZE(eukrea_mximxsd_modes),
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00040060,
-};
-
-static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd,
-				   unsigned int power)
-{
-	if (power)
-		gpio_direction_output(GPIO_LCDPWR, 1);
-	else
-		gpio_direction_output(GPIO_LCDPWR, 0);
-}
-
-static struct plat_lcd_data eukrea_mbimxsd_lcd_power_data = {
-	.set_power		= eukrea_mbimxsd_lcd_power_set,
-};
-
-static struct platform_device eukrea_mbimxsd_lcd_powerdev = {
-	.name			= "platform-lcd",
-	.dev.platform_data	= &eukrea_mbimxsd_lcd_power_data,
-};
-
-static const struct gpio_led eukrea_mbimxsd_leds[] __initconst = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.active_low		= 1,
-		.gpio			= GPIO_LED1,
-	},
-};
-
-static const struct gpio_led_platform_data
-		eukrea_mbimxsd_led_info __initconst = {
-	.leds		= eukrea_mbimxsd_leds,
-	.num_leds	= ARRAY_SIZE(eukrea_mbimxsd_leds),
-};
-
-static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
-	{
-		.gpio		= GPIO_SWITCH1,
-		.code		= BTN_0,
-		.desc		= "BP1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-};
-
-static const struct gpio_keys_platform_data
-		eukrea_mbimxsd_button_data __initconst = {
-	.buttons	= eukrea_mbimxsd_gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&eukrea_mbimxsd_lcd_powerdev,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("tlv320aic23", 0x1a),
-	},
-};
-
-static const
-struct imx_ssi_platform_data eukrea_mbimxsd_ssi_pdata __initconst = {
-	.flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE,
-};
-
-static struct esdhc_platform_data sd1_pdata = {
-	.cd_gpio = GPIO_SD1CD,
-	.cd_type = ESDHC_CD_GPIO,
-	.wp_type = ESDHC_WP_NONE,
-};
-
-static struct spi_board_info eukrea_mbimxsd25_spi_board_info[] __initdata = {
-	{
-		.modalias = "spidev",
-		.max_speed_hz = 20000000,
-		.bus_num = 0,
-		.chip_select = 0,
-		.mode = SPI_MODE_0,
-	},
-	{
-		.modalias = "spidev",
-		.max_speed_hz = 20000000,
-		.bus_num = 0,
-		.chip_select = 1,
-		.mode = SPI_MODE_0,
-	},
-};
-
-static int eukrea_mbimxsd25_spi_cs[] = {GPIO_SPI1_SS0, GPIO_SPI1_SS1};
-
-static const struct spi_imx_master eukrea_mbimxsd25_spi0_data __initconst = {
-	.chipselect     = eukrea_mbimxsd25_spi_cs,
-	.num_chipselect = ARRAY_SIZE(eukrea_mbimxsd25_spi_cs),
-};
-
-/*
- * system init for baseboard usage. Will be called by cpuimx25 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init eukrea_mbimxsd25_baseboard_init(void)
-{
-	if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
-			ARRAY_SIZE(eukrea_mbimxsd_pads)))
-		printk(KERN_ERR "error setting mbimxsd pads !\n");
-
-	imx25_add_imx_uart1(&uart_pdata);
-	imx25_add_imx_fb(&eukrea_mximxsd_fb_pdata);
-	imx25_add_imx_ssi(0, &eukrea_mbimxsd_ssi_pdata);
-
-	imx25_add_flexcan1();
-	imx25_add_sdhci_esdhc_imx(0, &sd1_pdata);
-
-	gpio_request(GPIO_LED1, "LED1");
-	gpio_direction_output(GPIO_LED1, 1);
-	gpio_free(GPIO_LED1);
-
-	gpio_request(GPIO_SWITCH1, "SWITCH1");
-	gpio_direction_input(GPIO_SWITCH1);
-	gpio_free(GPIO_SWITCH1);
-
-	gpio_request(GPIO_LCDPWR, "LCDPWR");
-	gpio_direction_output(GPIO_LCDPWR, 1);
-
-	i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
-				ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
-
-	gpio_request(GPIO_SPI1_IRQ, "SPI1_IRQ");
-	gpio_direction_input(GPIO_SPI1_IRQ);
-	gpio_free(GPIO_SPI1_IRQ);
-	imx25_add_spi_imx0(&eukrea_mbimxsd25_spi0_data);
-	spi_register_board_info(eukrea_mbimxsd25_spi_board_info,
-		ARRAY_SIZE(eukrea_mbimxsd25_spi_board_info));
-
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
-	imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
-	imx_add_platform_device("eukrea_tlv320", 0, NULL, 0, NULL, 0);
-}
diff --git a/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c b/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c
index 14d6c82..6edc940 100644
--- a/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c
+++ b/arch/arm/mach-imx/eukrea_mbimxsd35-baseboard.c
@@ -100,7 +100,7 @@
 	.num_modes	= ARRAY_SIZE(fb_modedb),
 };
 
-static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
+static const iomux_v3_cfg_t eukrea_mbimxsd_pads[] __initconst = {
 	/* LCD */
 	MX35_PAD_LD0__IPU_DISPB_DAT_0,
 	MX35_PAD_LD1__IPU_DISPB_DAT_1,
diff --git a/arch/arm/mach-imx/hardware.h b/arch/arm/mach-imx/hardware.h
index 66b2b56..76af2c0 100644
--- a/arch/arm/mach-imx/hardware.h
+++ b/arch/arm/mach-imx/hardware.h
@@ -112,7 +112,6 @@
 #include "mx21.h"
 #include "mx27.h"
 #include "mx1.h"
-#include "mx25.h"
 
 #define imx_map_entry(soc, name, _type)	{				\
 	.virtual = soc ## _IO_P2V(soc ## _ ## name ## _BASE_ADDR),	\
diff --git a/arch/arm/mach-imx/iomux-mx25.h b/arch/arm/mach-imx/iomux-mx25.h
deleted file mode 100644
index be51e83..0000000
--- a/arch/arm/mach-imx/iomux-mx25.h
+++ /dev/null
@@ -1,524 +0,0 @@
-/*
- * arch/arm/plat-mxc/include/mach/iomux-mx25.h
- *
- * Copyright (C) 2009 by Lothar Wassmann <LW@KARO-electronics.de>
- *
- * based on arch/arm/mach-mx25/mx25_pins.h
- *    Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
- * and
- * arch/arm/plat-mxc/include/mach/iomux-mx35.h
- *    Copyright (C) 2009 by Jan Weitzel Phytec Messtechnik GmbH <armlinux@phytec.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-#ifndef __MACH_IOMUX_MX25_H__
-#define __MACH_IOMUX_MX25_H__
-
-#include "iomux-v3.h"
-
-/*
- * IOMUX/PAD Bit field definitions
- */
-
-#define MX25_PAD_A10__A10		IOMUX_PAD(0x000, 0x008, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A10__GPIO_4_0		IOMUX_PAD(0x000, 0x008, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A13__A13		IOMUX_PAD(0x22C, 0x00c, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A13__GPIO_4_1		IOMUX_PAD(0x22C, 0x00c, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A14__A14		IOMUX_PAD(0x230, 0x010, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A14__GPIO_2_0		IOMUX_PAD(0x230, 0x010, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A15__A15		IOMUX_PAD(0x234, 0x014, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A15__GPIO_2_1		IOMUX_PAD(0x234, 0x014, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A16__A16		IOMUX_PAD(0x000, 0x018, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A16__GPIO_2_2		IOMUX_PAD(0x000, 0x018, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A17__A17		IOMUX_PAD(0x238, 0x01c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A17__GPIO_2_3		IOMUX_PAD(0x238, 0x01c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A18__A18		IOMUX_PAD(0x23c, 0x020, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A18__GPIO_2_4		IOMUX_PAD(0x23c, 0x020, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A18__FEC_COL		IOMUX_PAD(0x23c, 0x020, 0x17, 0x504, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A19__A19		IOMUX_PAD(0x240, 0x024, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A19__FEC_RX_ER		IOMUX_PAD(0x240, 0x024, 0x17, 0x518, 0, NO_PAD_CTRL)
-#define MX25_PAD_A19__GPIO_2_5		IOMUX_PAD(0x240, 0x024, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A20__A20		IOMUX_PAD(0x244, 0x028, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A20__GPIO_2_6		IOMUX_PAD(0x244, 0x028, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A20__FEC_RDATA2	IOMUX_PAD(0x244, 0x028, 0x17, 0x50c, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A21__A21		IOMUX_PAD(0x248, 0x02c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A21__GPIO_2_7		IOMUX_PAD(0x248, 0x02c, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A21__FEC_RDATA3	IOMUX_PAD(0x248, 0x02c, 0x17, 0x510, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A22__A22		IOMUX_PAD(0x000, 0x030, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A22__GPIO_2_8		IOMUX_PAD(0x000, 0x030, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A23__A23		IOMUX_PAD(0x24c, 0x034, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A23__GPIO_2_9		IOMUX_PAD(0x24c, 0x034, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A24__A24		IOMUX_PAD(0x250, 0x038, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A24__GPIO_2_10		IOMUX_PAD(0x250, 0x038, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A24__FEC_RX_CLK	IOMUX_PAD(0x250, 0x038, 0x17, 0x514, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_A25__A25		IOMUX_PAD(0x254, 0x03c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A25__GPIO_2_11		IOMUX_PAD(0x254, 0x03c, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_A25__FEC_CRS		IOMUX_PAD(0x254, 0x03c, 0x17, 0x508, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_EB0__EB0		IOMUX_PAD(0x258, 0x040, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_EB0__AUD4_TXD		IOMUX_PAD(0x258, 0x040, 0x14, 0x464, 0, NO_PAD_CTRL)
-#define MX25_PAD_EB0__GPIO_2_12		IOMUX_PAD(0x258, 0x040, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_EB1__EB1		IOMUX_PAD(0x25c, 0x044, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_EB1__AUD4_RXD		IOMUX_PAD(0x25c, 0x044, 0x14, 0x460, 0, NO_PAD_CTRL)
-#define MX25_PAD_EB1__GPIO_2_13		IOMUX_PAD(0x25c, 0x044, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_OE__OE			IOMUX_PAD(0x260, 0x048, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_OE__AUD4_TXC		IOMUX_PAD(0x260, 0x048, 0x14, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_OE__GPIO_2_14		IOMUX_PAD(0x260, 0x048, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CS0__CS0		IOMUX_PAD(0x000, 0x04c, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS0__GPIO_4_2		IOMUX_PAD(0x000, 0x04c, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CS1__CS1		IOMUX_PAD(0x000, 0x050, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS1__NF_CE3		IOMUX_PAD(0x000, 0x050, 0x01, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS1__GPIO_4_3		IOMUX_PAD(0x000, 0x050, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CS4__CS4		IOMUX_PAD(0x264, 0x054, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS4__NF_CE1		IOMUX_PAD(0x264, 0x054, 0x01, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS4__UART5_CTS		IOMUX_PAD(0x264, 0x054, 0x13, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS4__GPIO_3_20		IOMUX_PAD(0x264, 0x054, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CS5__CS5		IOMUX_PAD(0x268, 0x058, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS5__NF_CE2		IOMUX_PAD(0x268, 0x058, 0x01, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS5__UART5_RTS		IOMUX_PAD(0x268, 0x058, 0x13, 0x574, 0, NO_PAD_CTRL)
-#define MX25_PAD_CS5__GPIO_3_21		IOMUX_PAD(0x268, 0x058, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NF_CE0__NF_CE0		IOMUX_PAD(0x26c, 0x05c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NF_CE0__GPIO_3_22	IOMUX_PAD(0x26c, 0x05c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_ECB__ECB		IOMUX_PAD(0x270, 0x060, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_ECB__UART5_TXD_MUX	IOMUX_PAD(0x270, 0x060, 0x13, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_ECB__GPIO_3_23		IOMUX_PAD(0x270, 0x060, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LBA__LBA		IOMUX_PAD(0x274, 0x064, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_LBA__UART5_RXD_MUX	IOMUX_PAD(0x274, 0x064, 0x13, 0x578, 0, NO_PAD_CTRL)
-#define MX25_PAD_LBA__GPIO_3_24		IOMUX_PAD(0x274, 0x064, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_BCLK__BCLK		IOMUX_PAD(0x000, 0x068, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_BCLK__GPIO_4_4		IOMUX_PAD(0x000, 0x068, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_RW__RW			IOMUX_PAD(0x278, 0x06c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_RW__AUD4_TXFS		IOMUX_PAD(0x278, 0x06c, 0x14, 0x474, 0, NO_PAD_CTRL)
-#define MX25_PAD_RW__GPIO_3_25		IOMUX_PAD(0x278, 0x06c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFWE_B__NFWE_B		IOMUX_PAD(0x000, 0x070, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NFWE_B__GPIO_3_26	IOMUX_PAD(0x000, 0x070, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFRE_B__NFRE_B		IOMUX_PAD(0x000, 0x074, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NFRE_B__GPIO_3_27	IOMUX_PAD(0x000, 0x074, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFALE__NFALE		IOMUX_PAD(0x000, 0x078, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NFALE__GPIO_3_28	IOMUX_PAD(0x000, 0x078, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFCLE__NFCLE		IOMUX_PAD(0x000, 0x07c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NFCLE__GPIO_3_29	IOMUX_PAD(0x000, 0x07c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFWP_B__NFWP_B		IOMUX_PAD(0x000, 0x080, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_NFWP_B__GPIO_3_30	IOMUX_PAD(0x000, 0x080, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_NFRB__NFRB		IOMUX_PAD(0x27c, 0x084, 0x10, 0, 0, PAD_CTL_PKE)
-#define MX25_PAD_NFRB__GPIO_3_31	IOMUX_PAD(0x27c, 0x084, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D15__D15		IOMUX_PAD(0x280, 0x088, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D15__LD16		IOMUX_PAD(0x280, 0x088, 0x01, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_D15__GPIO_4_5		IOMUX_PAD(0x280, 0x088, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D14__D14		IOMUX_PAD(0x284, 0x08c, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D14__LD17		IOMUX_PAD(0x284, 0x08c, 0x01, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_D14__GPIO_4_6		IOMUX_PAD(0x284, 0x08c, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D13__D13		IOMUX_PAD(0x288, 0x090, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D13__LD18		IOMUX_PAD(0x288, 0x090, 0x01, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_D13__GPIO_4_7		IOMUX_PAD(0x288, 0x090, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D12__D12		IOMUX_PAD(0x28c, 0x094, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D12__GPIO_4_8		IOMUX_PAD(0x28c, 0x094, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D11__D11		IOMUX_PAD(0x290, 0x098, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D11__GPIO_4_9		IOMUX_PAD(0x290, 0x098, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D10__D10		IOMUX_PAD(0x294, 0x09c, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D10__GPIO_4_10		IOMUX_PAD(0x294, 0x09c, 0x05, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D10__USBOTG_OC		IOMUX_PAD(0x294, 0x09c, 0x06, 0x57c, 0, PAD_CTL_PUS_100K_UP)
-
-#define MX25_PAD_D9__D9			IOMUX_PAD(0x298, 0x0a0, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D9__GPIO_4_11		IOMUX_PAD(0x298, 0x0a0, 0x05, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D9__USBH2_PWR		IOMUX_PAD(0x298, 0x0a0, 0x06, 0, 0, PAD_CTL_PKE)
-
-#define MX25_PAD_D8__D8			IOMUX_PAD(0x29c, 0x0a4, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D8__GPIO_4_12		IOMUX_PAD(0x29c, 0x0a4, 0x05, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D8__USBH2_OC		IOMUX_PAD(0x29c, 0x0a4, 0x06, 0x580, 0, PAD_CTL_PUS_100K_UP)
-
-#define MX25_PAD_D7__D7			IOMUX_PAD(0x2a0, 0x0a8, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D7__GPIO_4_13		IOMUX_PAD(0x2a0, 0x0a8, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D6__D6			IOMUX_PAD(0x2a4, 0x0ac, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D6__GPIO_4_14		IOMUX_PAD(0x2a4, 0x0ac, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D5__D5			IOMUX_PAD(0x2a8, 0x0b0, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D5__GPIO_4_15		IOMUX_PAD(0x2a8, 0x0b0, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D4__D4			IOMUX_PAD(0x2ac, 0x0b4, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D4__GPIO_4_16		IOMUX_PAD(0x2ac, 0x0b4, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D3__D3			IOMUX_PAD(0x2b0, 0x0b8, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D3__GPIO_4_17		IOMUX_PAD(0x2b0, 0x0b8, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D2__D2			IOMUX_PAD(0x2b4, 0x0bc, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D2__GPIO_4_18		IOMUX_PAD(0x2b4, 0x0bc, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D1__D1			IOMUX_PAD(0x2b8, 0x0c0, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D1__GPIO_4_19		IOMUX_PAD(0x2b8, 0x0c0, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_D0__D0			IOMUX_PAD(0x2bc, 0x0c4, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_D0__GPIO_4_20		IOMUX_PAD(0x2bc, 0x0c4, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD0__LD0		IOMUX_PAD(0x2c0, 0x0c8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD0__CSI_D0		IOMUX_PAD(0x2c0, 0x0c8, 0x12, 0x488, 0, NO_PAD_CTRL)
-#define MX25_PAD_LD0__GPIO_2_15		IOMUX_PAD(0x2c0, 0x0c8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD1__LD1		IOMUX_PAD(0x2c4, 0x0cc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD1__CSI_D1		IOMUX_PAD(0x2c4, 0x0cc, 0x12, 0x48c, 0, NO_PAD_CTRL)
-#define MX25_PAD_LD1__GPIO_2_16		IOMUX_PAD(0x2c4, 0x0cc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD2__LD2		IOMUX_PAD(0x2c8, 0x0d0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD2__GPIO_2_17		IOMUX_PAD(0x2c8, 0x0d0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD3__LD3		IOMUX_PAD(0x2cc, 0x0d4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD3__GPIO_2_18		IOMUX_PAD(0x2cc, 0x0d4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD4__LD4		IOMUX_PAD(0x2d0, 0x0d8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD4__GPIO_2_19		IOMUX_PAD(0x2d0, 0x0d8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD5__LD5		IOMUX_PAD(0x2d4, 0x0dc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD5__GPIO_1_19		IOMUX_PAD(0x2d4, 0x0dc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD6__LD6		IOMUX_PAD(0x2d8, 0x0e0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD6__GPIO_1_20		IOMUX_PAD(0x2d8, 0x0e0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD7__LD7		IOMUX_PAD(0x2dc, 0x0e4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD7__GPIO_1_21		IOMUX_PAD(0x2dc, 0x0e4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD8__LD8		IOMUX_PAD(0x2e0, 0x0e8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD8__FEC_TX_ERR	IOMUX_PAD(0x2e0, 0x0e8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD9__LD9		IOMUX_PAD(0x2e4, 0x0ec, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD9__FEC_COL		IOMUX_PAD(0x2e4, 0x0ec, 0x15, 0x504, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_LD10__LD10		IOMUX_PAD(0x2e8, 0x0f0, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD10__FEC_RX_ER	IOMUX_PAD(0x2e8, 0x0f0, 0x15, 0x518, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_LD11__LD11		IOMUX_PAD(0x2ec, 0x0f4, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD11__FEC_RDATA2	IOMUX_PAD(0x2ec, 0x0f4, 0x15, 0x50c, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_LD12__LD12		IOMUX_PAD(0x2f0, 0x0f8, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD12__FEC_RDATA3	IOMUX_PAD(0x2f0, 0x0f8, 0x15, 0x510, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_LD13__LD13		IOMUX_PAD(0x2f4, 0x0fc, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD13__FEC_TDATA2	IOMUX_PAD(0x2f4, 0x0fc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD14__LD14		IOMUX_PAD(0x2f8, 0x100, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD14__FEC_TDATA3	IOMUX_PAD(0x2f8, 0x100, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LD15__LD15		IOMUX_PAD(0x2fc, 0x104, 0x10, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_LD15__FEC_RX_CLK	IOMUX_PAD(0x2fc, 0x104, 0x15, 0x514, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_HSYNC__HSYNC		IOMUX_PAD(0x300, 0x108, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_HSYNC__GPIO_1_22	IOMUX_PAD(0x300, 0x108, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_VSYNC__VSYNC		IOMUX_PAD(0x304, 0x10c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_VSYNC__GPIO_1_23	IOMUX_PAD(0x304, 0x10c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_LSCLK__LSCLK		IOMUX_PAD(0x308, 0x110, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_LSCLK__GPIO_1_24	IOMUX_PAD(0x308, 0x110, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_OE_ACD__OE_ACD		IOMUX_PAD(0x30c, 0x114, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_OE_ACD__GPIO_1_25	IOMUX_PAD(0x30c, 0x114, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CONTRAST__CONTRAST	IOMUX_PAD(0x310, 0x118, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CONTRAST__PWM4_PWMO	IOMUX_PAD(0x310, 0x118, 0x14, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CONTRAST__FEC_CRS	IOMUX_PAD(0x310, 0x118, 0x15, 0x508, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_PWM__PWM		IOMUX_PAD(0x314, 0x11c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_PWM__GPIO_1_26		IOMUX_PAD(0x314, 0x11c, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_PWM__USBH2_OC		IOMUX_PAD(0x314, 0x11c, 0x16, 0x580, 1, PAD_CTL_PUS_100K_UP)
-
-#define MX25_PAD_CSI_D2__CSI_D2		IOMUX_PAD(0x318, 0x120, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D2__UART5_RXD_MUX	IOMUX_PAD(0x318, 0x120, 0x11, 0x578, 1, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D2__GPIO_1_27	IOMUX_PAD(0x318, 0x120, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D2__CSPI3_MOSI	IOMUX_PAD(0x318, 0x120, 0x17, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D3__CSI_D3		IOMUX_PAD(0x31c, 0x124, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D3__GPIO_1_28	IOMUX_PAD(0x31c, 0x124, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D3__CSPI3_MISO	IOMUX_PAD(0x31c, 0x124, 0x17, 0x4b4, 1, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D4__CSI_D4		IOMUX_PAD(0x320, 0x128, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D4__UART5_RTS	IOMUX_PAD(0x320, 0x128, 0x11, 0x574, 1, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D4__GPIO_1_29	IOMUX_PAD(0x320, 0x128, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D4__CSPI3_SCLK	IOMUX_PAD(0x320, 0x128, 0x17, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D5__CSI_D5		IOMUX_PAD(0x324, 0x12c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D5__GPIO_1_30	IOMUX_PAD(0x324, 0x12c, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D5__CSPI3_RDY	IOMUX_PAD(0x324, 0x12c, 0x17, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D6__CSI_D6		IOMUX_PAD(0x328, 0x130, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D6__GPIO_1_31	IOMUX_PAD(0x328, 0x130, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D7__CSI_D7		IOMUX_PAD(0x32c, 0x134, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D7__GPIO_1_6	IOMUX_PAD(0x32c, 0x134, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D8__CSI_D8		IOMUX_PAD(0x330, 0x138, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D8__GPIO_1_7	IOMUX_PAD(0x330, 0x138, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_D9__CSI_D9		IOMUX_PAD(0x334, 0x13c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_D9__GPIO_4_21	IOMUX_PAD(0x334, 0x13c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_MCLK__CSI_MCLK	IOMUX_PAD(0x338, 0x140, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_MCLK__GPIO_1_8	IOMUX_PAD(0x338, 0x140, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_VSYNC__CSI_VSYNC	IOMUX_PAD(0x33c, 0x144, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_VSYNC__GPIO_1_9	IOMUX_PAD(0x33c, 0x144, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_HSYNC__CSI_HSYNC	IOMUX_PAD(0x340, 0x148, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_HSYNC__GPIO_1_10	IOMUX_PAD(0x340, 0x148, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK	IOMUX_PAD(0x344, 0x14c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSI_PIXCLK__GPIO_1_11	IOMUX_PAD(0x344, 0x14c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_I2C1_CLK__I2C1_CLK	IOMUX_PAD(0x348, 0x150, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_I2C1_CLK__GPIO_1_12	IOMUX_PAD(0x348, 0x150, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_I2C1_DAT__I2C1_DAT	IOMUX_PAD(0x34c, 0x154, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_I2C1_DAT__GPIO_1_13	IOMUX_PAD(0x34c, 0x154, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI	IOMUX_PAD(0x350, 0x158, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSPI1_MOSI__GPIO_1_14	IOMUX_PAD(0x350, 0x158, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_MISO__CSPI1_MISO	IOMUX_PAD(0x354, 0x15c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSPI1_MISO__GPIO_1_15	IOMUX_PAD(0x354, 0x15c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_SS0__CSPI1_SS0	IOMUX_PAD(0x358, 0x160, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSPI1_SS0__GPIO_1_16	IOMUX_PAD(0x358, 0x160, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_SS1__CSPI1_SS1	IOMUX_PAD(0x35c, 0x164, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSPI1_SS1__GPIO_1_17	IOMUX_PAD(0x35c, 0x164, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK	IOMUX_PAD(0x360, 0x168, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CSPI1_SCLK__GPIO_1_18	IOMUX_PAD(0x360, 0x168, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CSPI1_RDY__CSPI1_RDY	IOMUX_PAD(0x364, 0x16c, 0x10, 0, 0, PAD_CTL_PKE)
-#define MX25_PAD_CSPI1_RDY__GPIO_2_22	IOMUX_PAD(0x364, 0x16c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART1_RXD__UART1_RXD	IOMUX_PAD(0x368, 0x170, 0x10, 0, 0, PAD_CTL_PUS_100K_DOWN)
-#define MX25_PAD_UART1_RXD__GPIO_4_22	IOMUX_PAD(0x368, 0x170, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART1_TXD__UART1_TXD	IOMUX_PAD(0x36c, 0x174, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UART1_TXD__GPIO_4_23	IOMUX_PAD(0x36c, 0x174, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART1_RTS__UART1_RTS	IOMUX_PAD(0x370, 0x178, 0x10, 0, 0, PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_UART1_RTS__CSI_D0	IOMUX_PAD(0x370, 0x178, 0x11, 0x488, 1, NO_PAD_CTRL)
-#define MX25_PAD_UART1_RTS__GPIO_4_24	IOMUX_PAD(0x370, 0x178, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART1_CTS__UART1_CTS	IOMUX_PAD(0x374, 0x17c, 0x10, 0, 0, PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_UART1_CTS__CSI_D1	IOMUX_PAD(0x374, 0x17c, 0x11, 0x48c, 1, NO_PAD_CTRL)
-#define MX25_PAD_UART1_CTS__GPIO_4_25	IOMUX_PAD(0x374, 0x17c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART2_RXD__UART2_RXD	IOMUX_PAD(0x378, 0x180, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UART2_RXD__GPIO_4_26	IOMUX_PAD(0x378, 0x180, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART2_TXD__UART2_TXD	IOMUX_PAD(0x37c, 0x184, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UART2_TXD__GPIO_4_27	IOMUX_PAD(0x37c, 0x184, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART2_RTS__UART2_RTS	IOMUX_PAD(0x380, 0x188, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UART2_RTS__FEC_COL	IOMUX_PAD(0x380, 0x188, 0x12, 0x504, 2, NO_PAD_CTRL)
-#define MX25_PAD_UART2_RTS__GPIO_4_28	IOMUX_PAD(0x380, 0x188, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UART2_CTS__FEC_RX_ER	IOMUX_PAD(0x384, 0x18c, 0x12, 0x518, 2, NO_PAD_CTRL)
-#define MX25_PAD_UART2_CTS__UART2_CTS	IOMUX_PAD(0x384, 0x18c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UART2_CTS__GPIO_4_29	IOMUX_PAD(0x384, 0x18c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_CMD__SD1_CMD	IOMUX_PAD(0x388, 0x190, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_CMD__FEC_RDATA2	IOMUX_PAD(0x388, 0x190, 0x12, 0x50c, 2, NO_PAD_CTRL)
-#define MX25_PAD_SD1_CMD__GPIO_2_23	IOMUX_PAD(0x388, 0x190, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_CLK__SD1_CLK	IOMUX_PAD(0x38c, 0x194, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_CLK__FEC_RDATA3	IOMUX_PAD(0x38c, 0x194, 0x12, 0x510, 2, NO_PAD_CTRL)
-#define MX25_PAD_SD1_CLK__GPIO_2_24	IOMUX_PAD(0x38c, 0x194, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_DATA0__SD1_DATA0	IOMUX_PAD(0x390, 0x198, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_DATA0__GPIO_2_25	IOMUX_PAD(0x390, 0x198, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_DATA1__SD1_DATA1	IOMUX_PAD(0x394, 0x19c, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_DATA1__AUD7_RXD	IOMUX_PAD(0x394, 0x19c, 0x13, 0x478, 0, NO_PAD_CTRL)
-#define MX25_PAD_SD1_DATA1__GPIO_2_26	IOMUX_PAD(0x394, 0x19c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_DATA2__SD1_DATA2	IOMUX_PAD(0x398, 0x1a0, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_DATA2__FEC_RX_CLK	IOMUX_PAD(0x398, 0x1a0, 0x15, 0x514, 2, NO_PAD_CTRL)
-#define MX25_PAD_SD1_DATA2__GPIO_2_27	IOMUX_PAD(0x398, 0x1a0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_SD1_DATA3__SD1_DATA3	IOMUX_PAD(0x39c, 0x1a4, 0x10, 0, 0, PAD_CTL_PUS_47K_UP)
-#define MX25_PAD_SD1_DATA3__FEC_CRS	IOMUX_PAD(0x39c, 0x1a4, 0x10, 0x508, 2, NO_PAD_CTRL)
-#define MX25_PAD_SD1_DATA3__GPIO_2_28	IOMUX_PAD(0x39c, 0x1a4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define KPP_CTL_ROW	(PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
-#define KPP_CTL_COL	(PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
-
-#define MX25_PAD_KPP_ROW0__KPP_ROW0	IOMUX_PAD(0x3a0, 0x1a8, 0x10, 0, 0, KPP_CTL_ROW)
-#define MX25_PAD_KPP_ROW0__GPIO_2_29	IOMUX_PAD(0x3a0, 0x1a8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_ROW1__KPP_ROW1	IOMUX_PAD(0x3a4, 0x1ac, 0x10, 0, 0, KPP_CTL_ROW)
-#define MX25_PAD_KPP_ROW1__GPIO_2_30	IOMUX_PAD(0x3a4, 0x1ac, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_ROW2__KPP_ROW2	IOMUX_PAD(0x3a8, 0x1b0, 0x10, 0, 0, KPP_CTL_ROW)
-#define MX25_PAD_KPP_ROW2__CSI_D0	IOMUX_PAD(0x3a8, 0x1b0, 0x13, 0x488, 2, NO_PAD_CTRL)
-#define MX25_PAD_KPP_ROW2__GPIO_2_31	IOMUX_PAD(0x3a8, 0x1b0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_ROW3__KPP_ROW3	IOMUX_PAD(0x3ac, 0x1b4, 0x10, 0, 0, KPP_CTL_ROW)
-#define MX25_PAD_KPP_ROW3__CSI_LD1	IOMUX_PAD(0x3ac, 0x1b4, 0x13, 0x48c, 2, NO_PAD_CTRL)
-#define MX25_PAD_KPP_ROW3__GPIO_3_0	IOMUX_PAD(0x3ac, 0x1b4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_COL0__KPP_COL0	IOMUX_PAD(0x3b0, 0x1b8, 0x10, 0, 0, KPP_CTL_COL)
-#define MX25_PAD_KPP_COL0__UART4_RXD_MUX IOMUX_PAD(0x3b0, 0x1b8, 0x11, 0x570, 1, NO_PAD_CTRL)
-#define MX25_PAD_KPP_COL0__AUD5_TXD	IOMUX_PAD(0x3b0, 0x1b8, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_KPP_COL0__GPIO_3_1	IOMUX_PAD(0x3b0, 0x1b8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_COL1__KPP_COL1	IOMUX_PAD(0x3b4, 0x1bc, 0x10, 0, 0, KPP_CTL_COL)
-#define MX25_PAD_KPP_COL1__UART4_TXD_MUX IOMUX_PAD(0x3b4, 0x1bc, 0x11, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_KPP_COL1__AUD5_RXD	IOMUX_PAD(0x3b4, 0x1bc, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_KPP_COL1__GPIO_3_2	IOMUX_PAD(0x3b4, 0x1bc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_COL2__KPP_COL2	IOMUX_PAD(0x3b8, 0x1c0, 0x10, 0, 0, KPP_CTL_COL)
-#define MX25_PAD_KPP_COL2__UART4_RTS	IOMUX_PAD(0x3b8, 0x1c0, 0x11, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_KPP_COL2__AUD5_TXC	IOMUX_PAD(0x3b8, 0x1c0, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_KPP_COL2__GPIO_3_3	IOMUX_PAD(0x3b8, 0x1c0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_KPP_COL3__KPP_COL3	IOMUX_PAD(0x3bc, 0x1c4, 0x10, 0, 0, KPP_CTL_COL)
-#define MX25_PAD_KPP_COL3__UART4_CTS	IOMUX_PAD(0x3bc, 0x1c4, 0x11, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_KPP_COL3__AUD5_TXFS	IOMUX_PAD(0x3bc, 0x1c4, 0x12, 0, 0, PAD_CTL_PKE | PAD_CTL_PUS_100K_UP)
-#define MX25_PAD_KPP_COL3__GPIO_3_4	IOMUX_PAD(0x3bc, 0x1c4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_MDC__FEC_MDC	IOMUX_PAD(0x3c0, 0x1c8, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_FEC_MDC__AUD4_TXD	IOMUX_PAD(0x3c0, 0x1c8, 0x12, 0x464, 1, NO_PAD_CTRL)
-#define MX25_PAD_FEC_MDC__GPIO_3_5	IOMUX_PAD(0x3c0, 0x1c8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_MDIO__FEC_MDIO	IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)
-#define MX25_PAD_FEC_MDIO__AUD4_RXD	IOMUX_PAD(0x3c4, 0x1cc, 0x12, 0x460, 1, NO_PAD_CTRL)
-#define MX25_PAD_FEC_MDIO__GPIO_3_6	IOMUX_PAD(0x3c4, 0x1cc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_TDATA0__FEC_TDATA0	IOMUX_PAD(0x3c8, 0x1d0, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_FEC_TDATA0__GPIO_3_7	IOMUX_PAD(0x3c8, 0x1d0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_TDATA1__FEC_TDATA1	IOMUX_PAD(0x3cc, 0x1d4, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_FEC_TDATA1__AUD4_TXFS	IOMUX_PAD(0x3cc, 0x1d4, 0x12, 0x474, 1, NO_PAD_CTRL)
-#define MX25_PAD_FEC_TDATA1__GPIO_3_8	IOMUX_PAD(0x3cc, 0x1d4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_TX_EN__FEC_TX_EN	IOMUX_PAD(0x3d0, 0x1d8, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_FEC_TX_EN__GPIO_3_9   	IOMUX_PAD(0x3d0, 0x1d8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_RDATA0__FEC_RDATA0	IOMUX_PAD(0x3d4, 0x1dc, 0x10, 0, 0, PAD_CTL_PUS_100K_DOWN | NO_PAD_CTRL)
-#define MX25_PAD_FEC_RDATA0__GPIO_3_10	IOMUX_PAD(0x3d4, 0x1dc, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_RDATA1__FEC_RDATA1	IOMUX_PAD(0x3d8, 0x1e0, 0x10, 0, 0, PAD_CTL_PUS_100K_DOWN | NO_PAD_CTRL)
-#define MX25_PAD_FEC_RDATA1__GPIO_3_11	IOMUX_PAD(0x3d8, 0x1e0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_RX_DV__FEC_RX_DV	IOMUX_PAD(0x3dc, 0x1e4, 0x10, 0, 0, PAD_CTL_PUS_100K_DOWN | NO_PAD_CTRL)
-#define MX25_PAD_FEC_RX_DV__CAN2_RX	IOMUX_PAD(0x3dc, 0x1e4, 0x14, 0x484, 0, PAD_CTL_PUS_22K_UP)
-#define MX25_PAD_FEC_RX_DV__GPIO_3_12	IOMUX_PAD(0x3dc, 0x1e4, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK	IOMUX_PAD(0x3e0, 0x1e8, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN)
-#define MX25_PAD_FEC_TX_CLK__GPIO_3_13	IOMUX_PAD(0x3e0, 0x1e8, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_RTCK__RTCK		IOMUX_PAD(0x3e4, 0x1ec, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_RTCK__OWIRE		IOMUX_PAD(0x3e4, 0x1ec, 0x11, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_RTCK__GPIO_3_14	IOMUX_PAD(0x3e4, 0x1ec, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_DE_B__DE_B		IOMUX_PAD(0x3ec, 0x1f0, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_DE_B__GPIO_2_20	IOMUX_PAD(0x3ec, 0x1f0, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_TDO__TDO		IOMUX_PAD(0x3e8, 0x000, 0x00, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_GPIO_A__GPIO_A		IOMUX_PAD(0x3f0, 0x1f4, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_A__CAN1_TX	IOMUX_PAD(0x3f0, 0x1f4, 0x16, 0, 0, PAD_CTL_PUS_22K_UP)
-#define MX25_PAD_GPIO_A__USBOTG_PWR	IOMUX_PAD(0x3f0, 0x1f4, 0x12, 0, 0, PAD_CTL_PKE)
-
-#define MX25_PAD_GPIO_B__GPIO_B		IOMUX_PAD(0x3f4, 0x1f8, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_B__CAN1_RX	IOMUX_PAD(0x3f4, 0x1f8, 0x16, 0x480, 1, PAD_CTL_PUS_22K_UP)
-#define MX25_PAD_GPIO_B__USBOTG_OC	IOMUX_PAD(0x3f4, 0x1f8, 0x12, 0x57c, 1, PAD_CTL_PUS_100K_UP)
-
-#define MX25_PAD_GPIO_C__GPIO_C		IOMUX_PAD(0x3f8, 0x1fc, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_C__CAN2_TX	IOMUX_PAD(0x3f8, 0x1fc, 0x16, 0, 0, PAD_CTL_PUS_22K_UP)
-
-#define MX25_PAD_GPIO_D__GPIO_D		IOMUX_PAD(0x3fc, 0x200, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_E__LD16		IOMUX_PAD(0x400, 0x204, 0x02, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_GPIO_D__CAN2_RX	IOMUX_PAD(0x3fc, 0x200, 0x16, 0x484, 1, PAD_CTL_PUS_22K_UP)
-
-#define MX25_PAD_GPIO_E__GPIO_E		IOMUX_PAD(0x400, 0x204, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_F__LD17		IOMUX_PAD(0x404, 0x208, 0x02, 0, 0, PAD_CTL_SRE_FAST)
-#define MX25_PAD_GPIO_E__AUD7_TXD	IOMUX_PAD(0x400, 0x204, 0x14, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_GPIO_F__GPIO_F		IOMUX_PAD(0x404, 0x208, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_GPIO_F__AUD7_TXC	IOMUX_PAD(0x404, 0x208, 0x14, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK	IOMUX_PAD(0x000, 0x20c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_EXT_ARMCLK__GPIO_3_15	IOMUX_PAD(0x000, 0x20c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK IOMUX_PAD(0x000, 0x210, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16	IOMUX_PAD(0x000, 0x210, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_VSTBY_REQ__VSTBY_REQ	IOMUX_PAD(0x408, 0x214, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_VSTBY_REQ__AUD7_TXFS	IOMUX_PAD(0x408, 0x214, 0x14, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_VSTBY_REQ__GPIO_3_17	IOMUX_PAD(0x408, 0x214, 0x15, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_VSTBY_ACK__VSTBY_ACK	IOMUX_PAD(0x40c, 0x218, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_VSTBY_ACK__GPIO_3_18	IOMUX_PAD(0x40c, 0x218, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_POWER_FAIL__POWER_FAIL	IOMUX_PAD(0x410, 0x21c, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_POWER_FAIL__AUD7_RXD	IOMUX_PAD(0x410, 0x21c, 0x14, 0x478, 1, NO_PAD_CTRL)
-#define MX25_PAD_POWER_FAIL__GPIO_3_19	IOMUX_PAD(0x410, 0x21c, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CLKO__CLKO		IOMUX_PAD(0x414, 0x220, 0x10, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CLKO__GPIO_2_21	IOMUX_PAD(0x414, 0x220, 0x15, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_BOOT_MODE0__BOOT_MODE0	IOMUX_PAD(0x000, 0x224, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_BOOT_MODE0__GPIO_4_30	IOMUX_PAD(0x000, 0x224, 0x05, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_BOOT_MODE1__BOOT_MODE1	IOMUX_PAD(0x000, 0x228, 0x00, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_BOOT_MODE1__GPIO_4_31	IOMUX_PAD(0x000, 0x228, 0x05, 0, 0, NO_PAD_CTRL)
-
-#define MX25_PAD_CTL_GRP_DVS_MISC	IOMUX_PAD(0x418, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_FEC	IOMUX_PAD(0x41c, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_JTAG	IOMUX_PAD(0x420, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_NFC	IOMUX_PAD(0x424, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_CSI	IOMUX_PAD(0x428, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_WEIM	IOMUX_PAD(0x42c, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_DDR	IOMUX_PAD(0x430, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_CRM	IOMUX_PAD(0x434, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_KPP	IOMUX_PAD(0x438, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_SDHC1	IOMUX_PAD(0x43c, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_LCD	IOMUX_PAD(0x440, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_UART	IOMUX_PAD(0x444, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_NFC	IOMUX_PAD(0x448, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_CSI	IOMUX_PAD(0x44c, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DSE_CSPI1	IOMUX_PAD(0x450, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DDRTYPE	IOMUX_PAD(0x454, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_SDHC1	IOMUX_PAD(0x458, 0x000, 0, 0, 0, NO_PAD_CTRL)
-#define MX25_PAD_CTL_GRP_DVS_LCD	IOMUX_PAD(0x45c, 0x000, 0, 0, 0, NO_PAD_CTRL)
-
-#endif /* __MACH_IOMUX_MX25_H__ */
diff --git a/arch/arm/mach-imx/iomux-mx3.h b/arch/arm/mach-imx/iomux-mx3.h
index 0a5adba..2e4a0dd 100644
--- a/arch/arm/mach-imx/iomux-mx3.h
+++ b/arch/arm/mach-imx/iomux-mx3.h
@@ -114,7 +114,7 @@
  */
 int mxc_iomux_alloc_pin(unsigned int pin, const char *label);
 /*
- * setups mutliple pins
+ * setups multiple pins
  * convenient way to call the above function with tables
  */
 int mxc_iomux_setup_multiple_pins(const unsigned int *pin_list, unsigned count,
diff --git a/arch/arm/mach-imx/iomux-v3.c b/arch/arm/mach-imx/iomux-v3.c
index d61f960..a53b2e6 100644
--- a/arch/arm/mach-imx/iomux-v3.c
+++ b/arch/arm/mach-imx/iomux-v3.c
@@ -56,9 +56,10 @@
 	return 0;
 }
 
-int mxc_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t *pad_list, unsigned count)
+int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
+		unsigned count)
 {
-	iomux_v3_cfg_t *p = pad_list;
+	const iomux_v3_cfg_t *p = pad_list;
 	int i;
 	int ret;
 
diff --git a/arch/arm/mach-imx/iomux-v3.h b/arch/arm/mach-imx/iomux-v3.h
index 2fa3b54..f79e165 100644
--- a/arch/arm/mach-imx/iomux-v3.h
+++ b/arch/arm/mach-imx/iomux-v3.h
@@ -128,10 +128,11 @@
 int mxc_iomux_v3_setup_pad(iomux_v3_cfg_t pad);
 
 /*
- * setups mutliple pads
+ * setups multiple pads
  * convenient way to call the above function with tables
  */
-int mxc_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t *pad_list, unsigned count);
+int mxc_iomux_v3_setup_multiple_pads(const iomux_v3_cfg_t *pad_list,
+		unsigned count);
 
 /*
  * Initialise the iomux controller
diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
index 62a6e02..922ffd6 100644
--- a/arch/arm/mach-imx/mach-cpuimx35.c
+++ b/arch/arm/mach-imx/mach-cpuimx35.c
@@ -75,7 +75,7 @@
 	},
 };
 
-static iomux_v3_cfg_t eukrea_cpuimx35_pads[] = {
+static const iomux_v3_cfg_t eukrea_cpuimx35_pads[] __initconst = {
 	/* UART1 */
 	MX35_PAD_CTS1__UART1_CTS,
 	MX35_PAD_RTS1__UART1_RTS,
diff --git a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
deleted file mode 100644
index b2ee6e0..0000000
--- a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
+++ /dev/null
@@ -1,172 +0,0 @@
-/*
- * Copyright 2009 Sascha Hauer, <kernel@pengutronix.de>
- * Copyright 2010 Eric Bénard - Eukréa Electromatique, <eric@eukrea.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor,
- * Boston, MA  02110-1301, USA.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/ulpi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx25.h"
-#include "ehci.h"
-#include "eukrea-baseboards.h"
-#include "hardware.h"
-#include "iomux-mx25.h"
-#include "mx25.h"
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static iomux_v3_cfg_t eukrea_cpuimx25_pads[] = {
-	/* FEC - RMII */
-	MX25_PAD_FEC_MDC__FEC_MDC,
-	MX25_PAD_FEC_MDIO__FEC_MDIO,
-	MX25_PAD_FEC_TDATA0__FEC_TDATA0,
-	MX25_PAD_FEC_TDATA1__FEC_TDATA1,
-	MX25_PAD_FEC_TX_EN__FEC_TX_EN,
-	MX25_PAD_FEC_RDATA0__FEC_RDATA0,
-	MX25_PAD_FEC_RDATA1__FEC_RDATA1,
-	MX25_PAD_FEC_RX_DV__FEC_RX_DV,
-	MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
-	/* I2C1 */
-	MX25_PAD_I2C1_CLK__I2C1_CLK,
-	MX25_PAD_I2C1_DAT__I2C1_DAT,
-};
-
-static const struct fec_platform_data mx25_fec_pdata __initconst = {
-	.phy	= PHY_INTERFACE_MODE_RMII,
-};
-
-static const struct mxc_nand_platform_data
-eukrea_cpuimx25_nand_board_info __initconst = {
-	.width		= 1,
-	.hw_ecc		= 1,
-	.flash_bbt	= 1,
-};
-
-static const struct imxi2c_platform_data
-eukrea_cpuimx25_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct i2c_board_info eukrea_cpuimx25_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	},
-};
-
-static int eukrea_cpuimx25_otg_init(struct platform_device *pdev)
-{
-	return mx25_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static const struct mxc_usbh_platform_data otg_pdata __initconst = {
-	.init	= eukrea_cpuimx25_otg_init,
-	.portsc	= MXC_EHCI_MODE_UTMI,
-};
-
-static int eukrea_cpuimx25_usbh2_init(struct platform_device *pdev)
-{
-	return mx25_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_SINGLE_UNI |
-			MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN);
-}
-
-static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
-	.init	= eukrea_cpuimx25_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_SERIAL,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_UTMI,
-	.workaround     = FLS_USB2_WORKAROUND_ENGCM09152,
-};
-
-static bool otg_mode_host __initdata;
-
-static int __init eukrea_cpuimx25_otg_mode(char *options)
-{
-	if (!strcmp(options, "host"))
-		otg_mode_host = true;
-	else if (!strcmp(options, "device"))
-		otg_mode_host = false;
-	else
-		pr_info("otg_mode neither \"host\" nor \"device\". "
-			"Defaulting to device\n");
-	return 1;
-}
-__setup("otg_mode=", eukrea_cpuimx25_otg_mode);
-
-static void __init eukrea_cpuimx25_init(void)
-{
-	imx25_soc_init();
-
-	if (mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx25_pads,
-			ARRAY_SIZE(eukrea_cpuimx25_pads)))
-		printk(KERN_ERR "error setting cpuimx25 pads !\n");
-
-	imx25_add_imx_uart0(&uart_pdata);
-	imx25_add_mxc_nand(&eukrea_cpuimx25_nand_board_info);
-	imx25_add_imxdi_rtc();
-	imx25_add_fec(&mx25_fec_pdata);
-	imx25_add_imx2_wdt();
-
-	i2c_register_board_info(0, eukrea_cpuimx25_i2c_devices,
-				ARRAY_SIZE(eukrea_cpuimx25_i2c_devices));
-	imx25_add_imx_i2c0(&eukrea_cpuimx25_i2c0_data);
-
-	if (otg_mode_host)
-		imx25_add_mxc_ehci_otg(&otg_pdata);
-	else
-		imx25_add_fsl_usb2_udc(&otg_device_pdata);
-
-	imx25_add_mxc_ehci_hs(&usbh2_pdata);
-
-#ifdef CONFIG_MACH_EUKREA_MBIMXSD25_BASEBOARD
-	eukrea_mbimxsd25_baseboard_init();
-#endif
-}
-
-static void __init eukrea_cpuimx25_timer_init(void)
-{
-	mx25_clocks_init();
-}
-
-MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25")
-	/* Maintainer: Eukrea Electromatique */
-	.atag_offset = 0x100,
-	.map_io = mx25_map_io,
-	.init_early = imx25_init_early,
-	.init_irq = mx25_init_irq,
-	.init_time = eukrea_cpuimx25_timer_init,
-	.init_machine = eukrea_cpuimx25_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/imx25-dt.c b/arch/arm/mach-imx/mach-imx25.c
similarity index 67%
rename from arch/arm/mach-imx/imx25-dt.c
rename to arch/arm/mach-imx/mach-imx25.c
index 25defbd..9379fd0 100644
--- a/arch/arm/mach-imx/imx25-dt.c
+++ b/arch/arm/mach-imx/mach-imx25.c
@@ -10,12 +10,29 @@
  */
 
 #include <linux/irq.h>
+#include <linux/of_address.h>
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
 #include "common.h"
-#include "mx25.h"
+#include "hardware.h"
+
+static void __init imx25_init_early(void)
+{
+	mxc_set_cpu_type(MXC_CPU_MX25);
+}
+
+static void __init mx25_init_irq(void)
+{
+	struct device_node *np;
+	void __iomem *avic_base;
+
+	np = of_find_compatible_node(NULL, NULL, "fsl,avic");
+	avic_base = of_iomap(np, 0);
+	BUG_ON(!avic_base);
+	mxc_init_irq(avic_base);
+}
 
 static const char * const imx25_dt_board_compat[] __initconst = {
 	"fsl,imx25",
@@ -23,7 +40,6 @@
 };
 
 DT_MACHINE_START(IMX25_DT, "Freescale i.MX25 (Device Tree Support)")
-	.map_io		= mx25_map_io,
 	.init_early	= imx25_init_early,
 	.init_irq	= mx25_init_irq,
 	.dt_compat	= imx25_dt_board_compat,
diff --git a/arch/arm/mach-imx/mach-mx25_3ds.c b/arch/arm/mach-imx/mach-mx25_3ds.c
deleted file mode 100644
index 0d01e36..0000000
--- a/arch/arm/mach-imx/mach-mx25_3ds.c
+++ /dev/null
@@ -1,270 +0,0 @@
-/*
- * Copyright 2009 Sascha Hauer, <kernel@pengutronix.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor,
- * Boston, MA  02110-1301, USA.
- */
-
-/*
- * This machine is known as:
- *  - i.MX25 3-Stack Development System
- *  - i.MX25 Platform Development Kit (i.MX25 PDK)
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/usb/otg.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/memory.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices-imx25.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx25.h"
-#include "mx25.h"
-
-#define MX25PDK_CAN_PWDN	IMX_GPIO_NR(4, 6)
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static iomux_v3_cfg_t mx25pdk_pads[] = {
-	MX25_PAD_FEC_MDC__FEC_MDC,
-	MX25_PAD_FEC_MDIO__FEC_MDIO,
-	MX25_PAD_FEC_TDATA0__FEC_TDATA0,
-	MX25_PAD_FEC_TDATA1__FEC_TDATA1,
-	MX25_PAD_FEC_TX_EN__FEC_TX_EN,
-	MX25_PAD_FEC_RDATA0__FEC_RDATA0,
-	MX25_PAD_FEC_RDATA1__FEC_RDATA1,
-	MX25_PAD_FEC_RX_DV__FEC_RX_DV,
-	MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
-	MX25_PAD_A17__GPIO_2_3, /* FEC_EN, GPIO 35 */
-	MX25_PAD_D12__GPIO_4_8, /* FEC_RESET_B, GPIO 104 */
-
-	/* LCD */
-	MX25_PAD_LD0__LD0,
-	MX25_PAD_LD1__LD1,
-	MX25_PAD_LD2__LD2,
-	MX25_PAD_LD3__LD3,
-	MX25_PAD_LD4__LD4,
-	MX25_PAD_LD5__LD5,
-	MX25_PAD_LD6__LD6,
-	MX25_PAD_LD7__LD7,
-	MX25_PAD_LD8__LD8,
-	MX25_PAD_LD9__LD9,
-	MX25_PAD_LD10__LD10,
-	MX25_PAD_LD11__LD11,
-	MX25_PAD_LD12__LD12,
-	MX25_PAD_LD13__LD13,
-	MX25_PAD_LD14__LD14,
-	MX25_PAD_LD15__LD15,
-	MX25_PAD_GPIO_E__LD16,
-	MX25_PAD_GPIO_F__LD17,
-	MX25_PAD_HSYNC__HSYNC,
-	MX25_PAD_VSYNC__VSYNC,
-	MX25_PAD_LSCLK__LSCLK,
-	MX25_PAD_OE_ACD__OE_ACD,
-	MX25_PAD_CONTRAST__CONTRAST,
-
-	/* Keypad */
-	MX25_PAD_KPP_ROW0__KPP_ROW0,
-	MX25_PAD_KPP_ROW1__KPP_ROW1,
-	MX25_PAD_KPP_ROW2__KPP_ROW2,
-	MX25_PAD_KPP_ROW3__KPP_ROW3,
-	MX25_PAD_KPP_COL0__KPP_COL0,
-	MX25_PAD_KPP_COL1__KPP_COL1,
-	MX25_PAD_KPP_COL2__KPP_COL2,
-	MX25_PAD_KPP_COL3__KPP_COL3,
-
-	/* SD1 */
-	MX25_PAD_SD1_CMD__SD1_CMD,
-	MX25_PAD_SD1_CLK__SD1_CLK,
-	MX25_PAD_SD1_DATA0__SD1_DATA0,
-	MX25_PAD_SD1_DATA1__SD1_DATA1,
-	MX25_PAD_SD1_DATA2__SD1_DATA2,
-	MX25_PAD_SD1_DATA3__SD1_DATA3,
-	MX25_PAD_A14__GPIO_2_0, /* WriteProtect */
-	MX25_PAD_A15__GPIO_2_1, /* CardDetect */
-
-	/* I2C1 */
-	MX25_PAD_I2C1_CLK__I2C1_CLK,
-	MX25_PAD_I2C1_DAT__I2C1_DAT,
-
-	/* CAN1 */
-	MX25_PAD_GPIO_A__CAN1_TX,
-	MX25_PAD_GPIO_B__CAN1_RX,
-	MX25_PAD_D14__GPIO_4_6,	/* CAN_PWDN */
-};
-
-static const struct fec_platform_data mx25_fec_pdata __initconst = {
-	.phy    = PHY_INTERFACE_MODE_RMII,
-};
-
-#define FEC_ENABLE_GPIO		IMX_GPIO_NR(2, 3)
-#define FEC_RESET_B_GPIO	IMX_GPIO_NR(4, 8)
-
-static void __init mx25pdk_fec_reset(void)
-{
-	gpio_request(FEC_ENABLE_GPIO, "FEC PHY enable");
-	gpio_request(FEC_RESET_B_GPIO, "FEC PHY reset");
-
-	gpio_direction_output(FEC_ENABLE_GPIO, 0);  /* drop PHY power */
-	gpio_direction_output(FEC_RESET_B_GPIO, 0); /* assert reset */
-	udelay(2);
-
-	/* turn on PHY power and lift reset */
-	gpio_set_value(FEC_ENABLE_GPIO, 1);
-	gpio_set_value(FEC_RESET_B_GPIO, 1);
-}
-
-static const struct mxc_nand_platform_data
-mx25pdk_nand_board_info __initconst = {
-	.width		= 1,
-	.hw_ecc		= 1,
-	.flash_bbt	= 1,
-};
-
-static struct imx_fb_videomode mx25pdk_modes[] = {
-	{
-		.mode	= {
-			.name		= "CRT-VGA",
-			.refresh	= 60,
-			.xres		= 640,
-			.yres		= 480,
-			.pixclock	= 39683,
-			.left_margin	= 45,
-			.right_margin	= 114,
-			.upper_margin	= 33,
-			.lower_margin	= 11,
-			.hsync_len	= 1,
-			.vsync_len	= 1,
-		},
-		.bpp	= 16,
-		.pcr	= 0xFA208B80,
-	},
-};
-
-static const struct imx_fb_platform_data mx25pdk_fb_pdata __initconst = {
-	.mode		= mx25pdk_modes,
-	.num_modes	= ARRAY_SIZE(mx25pdk_modes),
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static const uint32_t mx25pdk_keymap[] = {
-	KEY(0, 0, KEY_UP),
-	KEY(0, 1, KEY_DOWN),
-	KEY(0, 2, KEY_VOLUMEDOWN),
-	KEY(0, 3, KEY_HOME),
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_LEFT),
-	KEY(1, 2, KEY_ENTER),
-	KEY(1, 3, KEY_VOLUMEUP),
-	KEY(2, 0, KEY_F6),
-	KEY(2, 1, KEY_F8),
-	KEY(2, 2, KEY_F9),
-	KEY(2, 3, KEY_F10),
-	KEY(3, 0, KEY_F1),
-	KEY(3, 1, KEY_F2),
-	KEY(3, 2, KEY_F3),
-	KEY(3, 3, KEY_POWER),
-};
-
-static const struct matrix_keymap_data mx25pdk_keymap_data __initconst = {
-	.keymap		= mx25pdk_keymap,
-	.keymap_size	= ARRAY_SIZE(mx25pdk_keymap),
-};
-
-static int mx25pdk_usbh2_init(struct platform_device *pdev)
-{
-	return mx25_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
-}
-
-static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
-	.init	= mx25pdk_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_SERIAL,
-};
-
-static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
-	.operating_mode = FSL_USB2_DR_DEVICE,
-	.phy_mode       = FSL_USB2_PHY_UTMI,
-};
-
-static const struct imxi2c_platform_data mx25_3ds_i2c0_data __initconst = {
-	.bitrate = 100000,
-};
-
-#define SD1_GPIO_WP	IMX_GPIO_NR(2, 0)
-#define SD1_GPIO_CD	IMX_GPIO_NR(2, 1)
-
-static const struct esdhc_platform_data mx25pdk_esdhc_pdata __initconst = {
-	.wp_gpio = SD1_GPIO_WP,
-	.cd_gpio = SD1_GPIO_CD,
-	.wp_type = ESDHC_WP_GPIO,
-	.cd_type = ESDHC_CD_GPIO,
-};
-
-static void __init mx25pdk_init(void)
-{
-	imx25_soc_init();
-
-	mxc_iomux_v3_setup_multiple_pads(mx25pdk_pads,
-			ARRAY_SIZE(mx25pdk_pads));
-
-	imx25_add_imx_uart0(&uart_pdata);
-	imx25_add_fsl_usb2_udc(&otg_device_pdata);
-	imx25_add_mxc_ehci_hs(&usbh2_pdata);
-	imx25_add_mxc_nand(&mx25pdk_nand_board_info);
-	imx25_add_imxdi_rtc();
-	imx25_add_imx_fb(&mx25pdk_fb_pdata);
-	imx25_add_imx2_wdt();
-
-	mx25pdk_fec_reset();
-	imx25_add_fec(&mx25_fec_pdata);
-	imx25_add_imx_keypad(&mx25pdk_keymap_data);
-
-	imx25_add_sdhci_esdhc_imx(0, &mx25pdk_esdhc_pdata);
-	imx25_add_imx_i2c0(&mx25_3ds_i2c0_data);
-
-	gpio_request_one(MX25PDK_CAN_PWDN, GPIOF_OUT_INIT_LOW, "can-pwdn");
-	imx25_add_flexcan0();
-}
-
-static void __init mx25pdk_timer_init(void)
-{
-	mx25_clocks_init();
-}
-
-MACHINE_START(MX25_3DS, "Freescale MX25PDK (3DS)")
-	/* Maintainer: Freescale Semiconductor, Inc. */
-	.atag_offset = 0x100,
-	.map_io = mx25_map_io,
-	.init_early = imx25_init_early,
-	.init_irq = mx25_init_irq,
-	.init_time	= mx25pdk_timer_init,
-	.init_machine = mx25pdk_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/mach-mx35_3ds.c b/arch/arm/mach-imx/mach-mx35_3ds.c
index 72cd77d..7e315f0 100644
--- a/arch/arm/mach-imx/mach-mx35_3ds.c
+++ b/arch/arm/mach-imx/mach-mx35_3ds.c
@@ -166,7 +166,7 @@
 	&mx35pdk_flash,
 };
 
-static iomux_v3_cfg_t mx35pdk_pads[] = {
+static const iomux_v3_cfg_t mx35pdk_pads[] __initconst = {
 	/* UART1 */
 	MX35_PAD_CTS1__UART1_CTS,
 	MX35_PAD_RTS1__UART1_RTS,
diff --git a/arch/arm/mach-imx/mach-pcm043.c b/arch/arm/mach-imx/mach-pcm043.c
index b623bca..e447e59 100644
--- a/arch/arm/mach-imx/mach-pcm043.c
+++ b/arch/arm/mach-imx/mach-pcm043.c
@@ -129,7 +129,7 @@
 	&pcm043_flash,
 };
 
-static iomux_v3_cfg_t pcm043_pads[] = {
+static const iomux_v3_cfg_t pcm043_pads[] __initconst = {
 	/* UART1 */
 	MX35_PAD_CTS1__UART1_CTS,
 	MX35_PAD_RTS1__UART1_RTS,
diff --git a/arch/arm/mach-imx/mach-vpr200.c b/arch/arm/mach-imx/mach-vpr200.c
index 97836e9..27a8f7e 100644
--- a/arch/arm/mach-imx/mach-vpr200.c
+++ b/arch/arm/mach-imx/mach-vpr200.c
@@ -161,7 +161,7 @@
 	}
 };
 
-static iomux_v3_cfg_t vpr200_pads[] = {
+static const iomux_v3_cfg_t vpr200_pads[] __initconst = {
 	/* UART1 */
 	MX35_PAD_TXD1__UART1_TXD_MUX,
 	MX35_PAD_RXD1__UART1_RXD_MUX,
diff --git a/arch/arm/mach-imx/mm-imx25.c b/arch/arm/mach-imx/mm-imx25.c
deleted file mode 100644
index 5211f62..0000000
--- a/arch/arm/mach-imx/mm-imx25.c
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- *  Copyright (C) 1999,2000 Arm Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *  Copyright (C) 2002 Shane Nay (shane@minirl.com)
- *  Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- *    - add MX31 specific definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/err.h>
-#include <linux/pinctrl/machine.h>
-
-#include <asm/pgtable.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "devices/devices-common.h"
-#include "hardware.h"
-#include "iomux-v3.h"
-#include "mx25.h"
-
-/*
- * This table defines static virtual address mappings for I/O regions.
- * These are the mappings common across all MX25 boards.
- */
-static struct map_desc mx25_io_desc[] __initdata = {
-	imx_map_entry(MX25, AVIC, MT_DEVICE_NONSHARED),
-	imx_map_entry(MX25, AIPS1, MT_DEVICE_NONSHARED),
-	imx_map_entry(MX25, AIPS2, MT_DEVICE_NONSHARED),
-};
-
-/*
- * This function initializes the memory map. It is called during the
- * system startup to create static physical to virtual memory mappings
- * for the IO modules.
- */
-void __init mx25_map_io(void)
-{
-	iotable_init(mx25_io_desc, ARRAY_SIZE(mx25_io_desc));
-}
-
-void __init imx25_init_early(void)
-{
-	mxc_set_cpu_type(MXC_CPU_MX25);
-	mxc_iomux_v3_init(MX25_IO_ADDRESS(MX25_IOMUXC_BASE_ADDR));
-}
-
-void __init mx25_init_irq(void)
-{
-	mxc_init_irq(MX25_IO_ADDRESS(MX25_AVIC_BASE_ADDR));
-}
-
-static struct sdma_platform_data imx25_sdma_pdata __initdata = {
-	.fw_name = "sdma-imx25.bin",
-};
-
-static const struct resource imx25_audmux_res[] __initconst = {
-	DEFINE_RES_MEM(MX25_AUDMUX_BASE_ADDR, SZ_16K),
-};
-
-void __init imx25_soc_init(void)
-{
-	mxc_arch_reset_init(MX25_IO_ADDRESS(MX25_WDOG_BASE_ADDR));
-	mxc_device_init();
-
-	/* i.mx25 has the i.mx35 type gpio */
-	mxc_register_gpio("imx35-gpio", 0, MX25_GPIO1_BASE_ADDR, SZ_16K, MX25_INT_GPIO1, 0);
-	mxc_register_gpio("imx35-gpio", 1, MX25_GPIO2_BASE_ADDR, SZ_16K, MX25_INT_GPIO2, 0);
-	mxc_register_gpio("imx35-gpio", 2, MX25_GPIO3_BASE_ADDR, SZ_16K, MX25_INT_GPIO3, 0);
-	mxc_register_gpio("imx35-gpio", 3, MX25_GPIO4_BASE_ADDR, SZ_16K, MX25_INT_GPIO4, 0);
-
-	pinctrl_provide_dummies();
-	/* i.mx25 has the i.mx35 type sdma */
-	imx_add_imx_sdma("imx35-sdma", MX25_SDMA_BASE_ADDR, MX25_INT_SDMA, &imx25_sdma_pdata);
-	/* i.mx25 has the i.mx31 type audmux */
-	platform_device_register_simple("imx31-audmux", 0, imx25_audmux_res,
-					ARRAY_SIZE(imx25_audmux_res));
-}
diff --git a/arch/arm/mach-imx/mx25.h b/arch/arm/mach-imx/mx25.h
deleted file mode 100644
index ec46640..0000000
--- a/arch/arm/mach-imx/mx25.h
+++ /dev/null
@@ -1,117 +0,0 @@
-#ifndef __MACH_MX25_H__
-#define __MACH_MX25_H__
-
-#define MX25_AIPS1_BASE_ADDR		0x43f00000
-#define MX25_AIPS1_SIZE			SZ_1M
-#define MX25_AIPS2_BASE_ADDR		0x53f00000
-#define MX25_AIPS2_SIZE			SZ_1M
-#define MX25_AVIC_BASE_ADDR		0x68000000
-#define MX25_AVIC_SIZE			SZ_1M
-
-#define MX25_I2C1_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0x80000)
-#define MX25_I2C3_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0x84000)
-#define MX25_CAN1_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0x88000)
-#define MX25_CAN2_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0x8c000)
-#define MX25_I2C2_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0x98000)
-#define MX25_CSPI1_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0xa4000)
-#define MX25_IOMUXC_BASE_ADDR		(MX25_AIPS1_BASE_ADDR + 0xac000)
-
-#define MX25_CRM_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0x80000)
-#define MX25_GPT1_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0x90000)
-#define MX25_GPIO4_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0x9c000)
-#define MX25_PWM2_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xa0000)
-#define MX25_GPIO3_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xa4000)
-#define MX25_PWM3_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xa8000)
-#define MX25_PWM4_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xc8000)
-#define MX25_GPIO1_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xcc000)
-#define MX25_GPIO2_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xd0000)
-#define MX25_WDOG_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xdc000)
-#define MX25_PWM1_BASE_ADDR		(MX25_AIPS2_BASE_ADDR + 0xe0000)
-
-#define MX25_UART1_BASE_ADDR		0x43f90000
-#define MX25_UART2_BASE_ADDR		0x43f94000
-#define MX25_AUDMUX_BASE_ADDR		0x43fb0000
-#define MX25_UART3_BASE_ADDR		0x5000c000
-#define MX25_UART4_BASE_ADDR		0x50008000
-#define MX25_UART5_BASE_ADDR		0x5002c000
-
-#define MX25_CSPI3_BASE_ADDR		0x50004000
-#define MX25_CSPI2_BASE_ADDR		0x50010000
-#define MX25_FEC_BASE_ADDR		0x50038000
-#define MX25_SSI2_BASE_ADDR		0x50014000
-#define MX25_SSI1_BASE_ADDR		0x50034000
-#define MX25_NFC_BASE_ADDR		0xbb000000
-#define MX25_IIM_BASE_ADDR		0x53ff0000
-#define MX25_DRYICE_BASE_ADDR		0x53ffc000
-#define MX25_ESDHC1_BASE_ADDR		0x53fb4000
-#define MX25_ESDHC2_BASE_ADDR		0x53fb8000
-#define MX25_LCDC_BASE_ADDR		0x53fbc000
-#define MX25_KPP_BASE_ADDR		0x43fa8000
-#define MX25_SDMA_BASE_ADDR		0x53fd4000
-#define MX25_USB_BASE_ADDR		0x53ff4000
-#define MX25_USB_OTG_BASE_ADDR			(MX25_USB_BASE_ADDR + 0x0000)
-/*
- * The reference manual (IMX25RM, Rev. 1, 06/2009) specifies an offset of 0x200
- * for the host controller.  Early documentation drafts specified 0x400 and
- * Freescale internal sources confirm only the latter value to work.
- */
-#define MX25_USB_HS_BASE_ADDR			(MX25_USB_BASE_ADDR + 0x0400)
-#define MX25_CSI_BASE_ADDR		0x53ff8000
-
-#define MX25_IO_P2V(x)			IMX_IO_P2V(x)
-#define MX25_IO_ADDRESS(x)		IOMEM(MX25_IO_P2V(x))
-
-/*
- * Interrupt numbers
- */
-#include <asm/irq.h>
-#define MX25_INT_CSPI3		(NR_IRQS_LEGACY + 0)
-#define MX25_INT_I2C1		(NR_IRQS_LEGACY + 3)
-#define MX25_INT_I2C2		(NR_IRQS_LEGACY + 4)
-#define MX25_INT_UART4		(NR_IRQS_LEGACY + 5)
-#define MX25_INT_ESDHC2		(NR_IRQS_LEGACY + 8)
-#define MX25_INT_ESDHC1		(NR_IRQS_LEGACY + 9)
-#define MX25_INT_I2C3		(NR_IRQS_LEGACY + 10)
-#define MX25_INT_SSI2		(NR_IRQS_LEGACY + 11)
-#define MX25_INT_SSI1		(NR_IRQS_LEGACY + 12)
-#define MX25_INT_CSPI2		(NR_IRQS_LEGACY + 13)
-#define MX25_INT_CSPI1		(NR_IRQS_LEGACY + 14)
-#define MX25_INT_GPIO3		(NR_IRQS_LEGACY + 16)
-#define MX25_INT_CSI		(NR_IRQS_LEGACY + 17)
-#define MX25_INT_UART3		(NR_IRQS_LEGACY + 18)
-#define MX25_INT_GPIO4		(NR_IRQS_LEGACY + 23)
-#define MX25_INT_KPP		(NR_IRQS_LEGACY + 24)
-#define MX25_INT_DRYICE		(NR_IRQS_LEGACY + 25)
-#define MX25_INT_PWM1		(NR_IRQS_LEGACY + 26)
-#define MX25_INT_UART2		(NR_IRQS_LEGACY + 32)
-#define MX25_INT_NFC		(NR_IRQS_LEGACY + 33)
-#define MX25_INT_SDMA		(NR_IRQS_LEGACY + 34)
-#define MX25_INT_USB_HS		(NR_IRQS_LEGACY + 35)
-#define MX25_INT_PWM2		(NR_IRQS_LEGACY + 36)
-#define MX25_INT_USB_OTG	(NR_IRQS_LEGACY + 37)
-#define MX25_INT_LCDC		(NR_IRQS_LEGACY + 39)
-#define MX25_INT_UART5		(NR_IRQS_LEGACY + 40)
-#define MX25_INT_PWM3		(NR_IRQS_LEGACY + 41)
-#define MX25_INT_PWM4		(NR_IRQS_LEGACY + 42)
-#define MX25_INT_CAN1		(NR_IRQS_LEGACY + 43)
-#define MX25_INT_CAN2		(NR_IRQS_LEGACY + 44)
-#define MX25_INT_UART1		(NR_IRQS_LEGACY + 45)
-#define MX25_INT_GPIO2		(NR_IRQS_LEGACY + 51)
-#define MX25_INT_GPIO1		(NR_IRQS_LEGACY + 52)
-#define MX25_INT_GPT1		(NR_IRQS_LEGACY + 54)
-#define MX25_INT_FEC		(NR_IRQS_LEGACY + 57)
-
-#define MX25_DMA_REQ_SSI2_RX1	22
-#define MX25_DMA_REQ_SSI2_TX1	23
-#define MX25_DMA_REQ_SSI2_RX0	24
-#define MX25_DMA_REQ_SSI2_TX0	25
-#define MX25_DMA_REQ_SSI1_RX1	26
-#define MX25_DMA_REQ_SSI1_TX1	27
-#define MX25_DMA_REQ_SSI1_RX0	28
-#define MX25_DMA_REQ_SSI1_TX0	29
-
-#ifndef __ASSEMBLY__
-extern int mx25_revision(void);
-#endif
-
-#endif /* ifndef __MACH_MX25_H__ */
diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
deleted file mode 100644
index a6b50e6..0000000
--- a/arch/arm/mach-msm/Kconfig
+++ /dev/null
@@ -1,109 +0,0 @@
-if ARCH_MSM
-
-choice
-	prompt "Qualcomm MSM SoC Type"
-	default ARCH_MSM7X00A
-	depends on ARCH_MSM
-
-config ARCH_MSM7X00A
-	bool "MSM7x00A / MSM7x01A"
-	select ARCH_MSM_ARM11
-	select CPU_V6
-	select GPIO_MSM_V1
-	select MACH_TROUT if !MACH_HALIBUT
-	select MSM_PROC_COMM
-	select MSM_SMD
-	select CLKSRC_QCOM
-	select MSM_SMD_PKG3
-
-config ARCH_MSM7X30
-	bool "MSM7x30"
-	select ARCH_MSM_SCORPION
-	select CPU_V7
-	select GPIO_MSM_V1
-	select MACH_MSM7X30_SURF # if !
-	select MSM_GPIOMUX
-	select MSM_PROC_COMM
-	select MSM_SMD
-	select CLKSRC_QCOM
-	select MSM_VIC
-
-config ARCH_QSD8X50
-	bool "QSD8X50"
-	select ARCH_MSM_SCORPION
-	select CPU_V7
-	select GPIO_MSM_V1
-	select MACH_QSD8X50_SURF if !MACH_QSD8X50A_ST1_5
-	select MSM_GPIOMUX
-	select MSM_PROC_COMM
-	select MSM_SMD
-	select CLKSRC_QCOM
-	select MSM_VIC
-
-endchoice
-
-config MSM_SOC_REV_A
-	bool
-
-config  ARCH_MSM_ARM11
-	bool
-
-config  ARCH_MSM_SCORPION
-	bool
-
-config  MSM_VIC
-	bool
-
-menu "Qualcomm MSM Board Type"
-	depends on ARCH_MSM
-
-config MACH_HALIBUT
-	depends on ARCH_MSM
-	depends on ARCH_MSM7X00A
-	bool "Halibut Board (QCT SURF7201A)"
-	help
-	  Support for the Qualcomm SURF7201A eval board.
-
-config MACH_TROUT
-	depends on ARCH_MSM
-	depends on ARCH_MSM7X00A
-	bool "HTC Dream (aka trout)"
-	help
-	  Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
-
-config MACH_MSM7X30_SURF
-	depends on ARCH_MSM7X30
-	bool "MSM7x30 SURF"
-	help
-	  Support for the Qualcomm MSM7x30 SURF eval board.
-
-config MACH_QSD8X50_SURF
-	depends on ARCH_QSD8X50
-	bool "QSD8x50 SURF"
-	help
-	  Support for the Qualcomm QSD8x50 SURF eval board.
-
-config MACH_QSD8X50A_ST1_5
-	depends on ARCH_QSD8X50
-	bool "QSD8x50A ST1.5"
-	select MSM_SOC_REV_A
-	help
-	  Support for the Qualcomm ST1.5.
-
-endmenu
-
-config MSM_SMD_PKG3
-	bool
-
-config MSM_PROC_COMM
-	bool
-
-config MSM_SMD
-	bool
-
-config MSM_GPIOMUX
-	bool
-	help
-	  Support for MSM V1 TLMM GPIOMUX architecture.
-
-endif
diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
deleted file mode 100644
index 27c078a..0000000
--- a/arch/arm/mach-msm/Makefile
+++ /dev/null
@@ -1,23 +0,0 @@
-obj-$(CONFIG_MSM_PROC_COMM) += clock.o
-
-obj-$(CONFIG_MSM_VIC) += irq-vic.o
-
-obj-$(CONFIG_ARCH_MSM7X00A) += irq.o
-obj-$(CONFIG_ARCH_QSD8X50) += sirc.o
-
-obj-$(CONFIG_MSM_PROC_COMM) += proc_comm.o clock-pcom.o vreg.o
-
-obj-$(CONFIG_ARCH_MSM7X00A) += dma.o io.o
-obj-$(CONFIG_ARCH_MSM7X30) += dma.o io.o
-obj-$(CONFIG_ARCH_QSD8X50) += dma.o io.o
-
-obj-$(CONFIG_MSM_SMD) += smd.o smd_debug.o
-obj-$(CONFIG_MSM_SMD) += last_radio_log.o
-
-obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o devices-msm7x00.o
-obj-$(CONFIG_MACH_TROUT) += board-trout.o board-trout-gpio.o board-trout-mmc.o board-trout-panel.o devices-msm7x00.o
-obj-$(CONFIG_MACH_HALIBUT) += board-halibut.o devices-msm7x00.o
-obj-$(CONFIG_ARCH_MSM7X30) += board-msm7x30.o devices-msm7x30.o
-obj-$(CONFIG_ARCH_QSD8X50) += board-qsd8x50.o devices-qsd8x50.o
-obj-$(CONFIG_MSM_GPIOMUX) += gpiomux.o
-obj-$(CONFIG_ARCH_QSD8X50) += gpiomux-8x50.o
diff --git a/arch/arm/mach-msm/Makefile.boot b/arch/arm/mach-msm/Makefile.boot
deleted file mode 100644
index 9b803a5..0000000
--- a/arch/arm/mach-msm/Makefile.boot
+++ /dev/null
@@ -1,3 +0,0 @@
-  zreladdr-y		+= 0x10008000
-params_phys-y		:= 0x10000100
-initrd_phys-y		:= 0x10800000
diff --git a/arch/arm/mach-msm/board-halibut.c b/arch/arm/mach-msm/board-halibut.c
deleted file mode 100644
index fc83204..0000000
--- a/arch/arm/mach-msm/board-halibut.c
+++ /dev/null
@@ -1,110 +0,0 @@
-/* linux/arch/arm/mach-msm/board-halibut.c
- *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/io.h>
-#include <linux/delay.h>
-#include <linux/smc91x.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/setup.h>
-
-#include <mach/irqs.h>
-#include <mach/msm_iomap.h>
-
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-
-#include "devices.h"
-#include "common.h"
-
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.start	= 0x9C004300,
-		.end	= 0x9C004400,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= MSM_GPIO_TO_INT(49),
-		.end	= MSM_GPIO_TO_INT(49),
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-static struct smc91x_platdata smc91x_platdata = {
-	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
-};
-
-static struct platform_device smc91x_device = {
-	.name		= "smc91x",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(smc91x_resources),
-	.resource	= smc91x_resources,
-	.dev.platform_data = &smc91x_platdata,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&msm_clock_7x01a,
-	&msm_device_gpio_7201,
-	&msm_device_uart3,
-	&msm_device_smd,
-	&msm_device_nand,
-	&msm_device_hsusb,
-	&msm_device_i2c,
-	&smc91x_device,
-};
-
-static void __init halibut_init_early(void)
-{
-	arch_ioremap_caller = __msm_ioremap_caller;
-}
-
-static void __init halibut_init_irq(void)
-{
-	msm_init_irq();
-}
-
-static void __init halibut_init(void)
-{
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-static void __init halibut_map_io(void)
-{
-	msm_map_common_io();
-}
-
-static void __init halibut_init_late(void)
-{
-	smd_debugfs_init();
-}
-
-MACHINE_START(HALIBUT, "Halibut Board (QCT SURF7200A)")
-	.atag_offset	= 0x100,
-	.map_io		= halibut_map_io,
-	.init_early	= halibut_init_early,
-	.init_irq	= halibut_init_irq,
-	.init_machine	= halibut_init,
-	.init_late	= halibut_init_late,
-	.init_time	= msm7x01_timer_init,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-msm7x30.c b/arch/arm/mach-msm/board-msm7x30.c
deleted file mode 100644
index 8f5ecdc..0000000
--- a/arch/arm/mach-msm/board-msm7x30.c
+++ /dev/null
@@ -1,191 +0,0 @@
-/* Copyright (c) 2009-2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/smsc911x.h>
-#include <linux/usb/msm_hsusb.h>
-#include <linux/clkdev.h>
-#include <linux/memblock.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/memory.h>
-#include <asm/setup.h>
-
-#include <mach/clk.h>
-#include <mach/msm_iomap.h>
-#include <mach/dma.h>
-
-#include <mach/vreg.h>
-#include "devices.h"
-#include "gpiomux.h"
-#include "proc_comm.h"
-#include "common.h"
-
-static void __init msm7x30_fixup(struct tag *tag, char **cmdline)
-{
-	for (; tag->hdr.size; tag = tag_next(tag))
-		if (tag->hdr.tag == ATAG_MEM && tag->u.mem.start == 0x200000) {
-			tag->u.mem.start = 0;
-			tag->u.mem.size += SZ_2M;
-		}
-}
-
-static void __init msm7x30_reserve(void)
-{
-	memblock_remove(0x0, SZ_2M);
-}
-
-static int hsusb_phy_init_seq[] = {
-	0x30, 0x32,	/* Enable and set Pre-Emphasis Depth to 20% */
-	0x02, 0x36,	/* Disable CDR Auto Reset feature */
-	-1
-};
-
-static int hsusb_link_clk_reset(struct clk *link_clk, bool assert)
-{
-	int ret;
-
-	if (assert) {
-		ret = clk_reset(link_clk, CLK_RESET_ASSERT);
-		if (ret)
-			pr_err("usb hs_clk assert failed\n");
-	} else {
-		ret = clk_reset(link_clk, CLK_RESET_DEASSERT);
-		if (ret)
-			pr_err("usb hs_clk deassert failed\n");
-	}
-	return ret;
-}
-
-static int hsusb_phy_clk_reset(struct clk *phy_clk)
-{
-	int ret;
-
-	ret = clk_reset(phy_clk, CLK_RESET_ASSERT);
-	if (ret) {
-		pr_err("usb phy clk assert failed\n");
-		return ret;
-	}
-	usleep_range(10000, 12000);
-	ret = clk_reset(phy_clk, CLK_RESET_DEASSERT);
-	if (ret)
-		pr_err("usb phy clk deassert failed\n");
-	return ret;
-}
-
-static struct msm_otg_platform_data msm_otg_pdata = {
-	.phy_init_seq		= hsusb_phy_init_seq,
-	.mode                   = USB_DR_MODE_PERIPHERAL,
-	.otg_control		= OTG_PHY_CONTROL,
-	.link_clk_reset		= hsusb_link_clk_reset,
-	.phy_clk_reset		= hsusb_phy_clk_reset,
-};
-
-struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
-#ifdef CONFIG_SERIAL_MSM_CONSOLE
-	[49] = { /* UART2 RFR */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
-	},
-	[50] = { /* UART2 CTS */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
-	},
-	[51] = { /* UART2 RX */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
-	},
-	[52] = { /* UART2 TX */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_2 | GPIOMUX_VALID,
-	},
-#endif
-};
-
-static struct platform_device *devices[] __initdata = {
-	&msm_clock_7x30,
-	&msm_device_gpio_7x30,
-#if defined(CONFIG_SERIAL_MSM)
-        &msm_device_uart2,
-#endif
-	&msm_device_smd,
-	&msm_device_otg,
-	&msm_device_hsusb,
-	&msm_device_hsusb_host,
-};
-
-static void __init msm7x30_init_irq(void)
-{
-	msm_init_irq();
-}
-
-static void __init msm7x30_init(void)
-{
-	msm_device_otg.dev.platform_data = &msm_otg_pdata;
-	msm_device_hsusb.dev.parent = &msm_device_otg.dev;
-	msm_device_hsusb_host.dev.parent = &msm_device_otg.dev;
-
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-static void __init msm7x30_map_io(void)
-{
-	msm_map_msm7x30_io();
-}
-
-static void __init msm7x30_init_late(void)
-{
-	smd_debugfs_init();
-}
-
-MACHINE_START(MSM7X30_SURF, "QCT MSM7X30 SURF")
-	.atag_offset = 0x100,
-	.fixup = msm7x30_fixup,
-	.reserve = msm7x30_reserve,
-	.map_io = msm7x30_map_io,
-	.init_irq = msm7x30_init_irq,
-	.init_machine = msm7x30_init,
-	.init_late = msm7x30_init_late,
-	.init_time	= msm7x30_timer_init,
-MACHINE_END
-
-MACHINE_START(MSM7X30_FFA, "QCT MSM7X30 FFA")
-	.atag_offset = 0x100,
-	.fixup = msm7x30_fixup,
-	.reserve = msm7x30_reserve,
-	.map_io = msm7x30_map_io,
-	.init_irq = msm7x30_init_irq,
-	.init_machine = msm7x30_init,
-	.init_late = msm7x30_init_late,
-	.init_time	= msm7x30_timer_init,
-MACHINE_END
-
-MACHINE_START(MSM7X30_FLUID, "QCT MSM7X30 FLUID")
-	.atag_offset = 0x100,
-	.fixup = msm7x30_fixup,
-	.reserve = msm7x30_reserve,
-	.map_io = msm7x30_map_io,
-	.init_irq = msm7x30_init_irq,
-	.init_machine = msm7x30_init,
-	.init_late = msm7x30_init_late,
-	.init_time	= msm7x30_timer_init,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-qsd8x50.c b/arch/arm/mach-msm/board-qsd8x50.c
deleted file mode 100644
index 10016a3..0000000
--- a/arch/arm/mach-msm/board-qsd8x50.c
+++ /dev/null
@@ -1,254 +0,0 @@
-/* Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/usb/msm_hsusb.h>
-#include <linux/err.h>
-#include <linux/clkdev.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/io.h>
-#include <asm/setup.h>
-
-#include <mach/irqs.h>
-#include <mach/sirc.h>
-#include <mach/vreg.h>
-#include <mach/clk.h>
-#include <linux/platform_data/mmc-msm_sdcc.h>
-
-#include "devices.h"
-#include "common.h"
-
-static const resource_size_t qsd8x50_surf_smc91x_base __initconst = 0x70000300;
-static const unsigned        qsd8x50_surf_smc91x_gpio __initconst = 156;
-
-/* Leave smc91x resources empty here, as we'll fill them in
- * at run-time: they vary from board to board, and the true
- * configuration won't be known until boot.
- */
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-static struct smc91x_platdata smc91x_platdata = {
-	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
-};
-
-static struct platform_device smc91x_device = {
-	.name           = "smc91x",
-	.id             = 0,
-	.num_resources  = ARRAY_SIZE(smc91x_resources),
-	.resource       = smc91x_resources,
-	.dev.platform_data = &smc91x_platdata,
-};
-
-static int __init msm_init_smc91x(void)
-{
-	if (machine_is_qsd8x50_surf()) {
-		smc91x_resources[0].start = qsd8x50_surf_smc91x_base;
-		smc91x_resources[0].end   = qsd8x50_surf_smc91x_base + 0xff;
-		smc91x_resources[1].start =
-			gpio_to_irq(qsd8x50_surf_smc91x_gpio);
-		smc91x_resources[1].end   =
-			gpio_to_irq(qsd8x50_surf_smc91x_gpio);
-		platform_device_register(&smc91x_device);
-	}
-
-	return 0;
-}
-module_init(msm_init_smc91x);
-
-static int hsusb_phy_init_seq[] = {
-	0x08, 0x31,	/* Increase HS Driver Amplitude */
-	0x20, 0x32,	/* Enable and set Pre-Emphasis Depth to 10% */
-	-1
-};
-
-static int hsusb_link_clk_reset(struct clk *link_clk, bool assert)
-{
-	int ret;
-
-	if (assert) {
-		ret = clk_reset(link_clk, CLK_RESET_ASSERT);
-		if (ret)
-			pr_err("usb hs_clk assert failed\n");
-	} else {
-		ret = clk_reset(link_clk, CLK_RESET_DEASSERT);
-		if (ret)
-			pr_err("usb hs_clk deassert failed\n");
-	}
-	return ret;
-}
-
-static int hsusb_phy_clk_reset(struct clk *phy_clk)
-{
-	int ret;
-
-	ret = clk_reset(phy_clk, CLK_RESET_ASSERT);
-	if (ret) {
-		pr_err("usb phy clk assert failed\n");
-		return ret;
-	}
-	usleep_range(10000, 12000);
-	ret = clk_reset(phy_clk, CLK_RESET_DEASSERT);
-	if (ret)
-		pr_err("usb phy clk deassert failed\n");
-	return ret;
-}
-
-static struct msm_otg_platform_data msm_otg_pdata = {
-	.phy_init_seq		= hsusb_phy_init_seq,
-	.mode                   = USB_DR_MODE_PERIPHERAL,
-	.otg_control		= OTG_PHY_CONTROL,
-	.link_clk_reset		= hsusb_link_clk_reset,
-	.phy_clk_reset		= hsusb_phy_clk_reset,
-};
-
-static struct platform_device *devices[] __initdata = {
-	&msm_clock_8x50,
-	&msm_device_gpio_8x50,
-	&msm_device_uart3,
-	&msm_device_smd,
-	&msm_device_otg,
-	&msm_device_hsusb,
-	&msm_device_hsusb_host,
-};
-
-static struct msm_mmc_gpio sdc1_gpio_cfg[] = {
-	{51, "sdc1_dat_3"},
-	{52, "sdc1_dat_2"},
-	{53, "sdc1_dat_1"},
-	{54, "sdc1_dat_0"},
-	{55, "sdc1_cmd"},
-	{56, "sdc1_clk"}
-};
-
-static struct vreg *vreg_mmc;
-static unsigned long vreg_sts;
-
-static uint32_t msm_sdcc_setup_power(struct device *dv, unsigned int vdd)
-{
-	int rc = 0;
-	struct platform_device *pdev;
-
-	pdev = container_of(dv, struct platform_device, dev);
-
-	if (vdd == 0) {
-		if (!vreg_sts)
-			return 0;
-
-		clear_bit(pdev->id, &vreg_sts);
-
-		if (!vreg_sts) {
-			rc = vreg_disable(vreg_mmc);
-			if (rc)
-				pr_err("vreg_mmc disable failed for slot "
-						"%d: %d\n", pdev->id, rc);
-		}
-		return 0;
-	}
-
-	if (!vreg_sts) {
-		rc = vreg_set_level(vreg_mmc, 2900);
-		if (rc)
-			pr_err("vreg_mmc set level failed for slot %d: %d\n",
-					pdev->id, rc);
-		rc = vreg_enable(vreg_mmc);
-		if (rc)
-			pr_err("vreg_mmc enable failed for slot %d: %d\n",
-					pdev->id, rc);
-	}
-	set_bit(pdev->id, &vreg_sts);
-	return 0;
-}
-
-static struct msm_mmc_gpio_data sdc1_gpio = {
-	.gpio = sdc1_gpio_cfg,
-	.size = ARRAY_SIZE(sdc1_gpio_cfg),
-};
-
-static struct msm_mmc_platform_data qsd8x50_sdc1_data = {
-	.ocr_mask	= MMC_VDD_27_28 | MMC_VDD_28_29,
-	.translate_vdd	= msm_sdcc_setup_power,
-	.gpio_data = &sdc1_gpio,
-};
-
-static void __init qsd8x50_init_mmc(void)
-{
-	vreg_mmc = vreg_get(NULL, "gp5");
-
-	if (IS_ERR(vreg_mmc)) {
-		pr_err("vreg get for vreg_mmc failed (%ld)\n",
-				PTR_ERR(vreg_mmc));
-		return;
-	}
-
-	msm_add_sdcc(1, &qsd8x50_sdc1_data, 0, 0);
-}
-
-static void __init qsd8x50_map_io(void)
-{
-	msm_map_qsd8x50_io();
-}
-
-static void __init qsd8x50_init_irq(void)
-{
-	msm_init_irq();
-	msm_init_sirc();
-}
-
-static void __init qsd8x50_init(void)
-{
-	msm_device_otg.dev.platform_data = &msm_otg_pdata;
-	msm_device_hsusb.dev.parent = &msm_device_otg.dev;
-	msm_device_hsusb_host.dev.parent = &msm_device_otg.dev;
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-	qsd8x50_init_mmc();
-}
-
-static void __init qsd8x50_init_late(void)
-{
-	smd_debugfs_init();
-}
-
-MACHINE_START(QSD8X50_SURF, "QCT QSD8X50 SURF")
-	.atag_offset = 0x100,
-	.map_io = qsd8x50_map_io,
-	.init_irq = qsd8x50_init_irq,
-	.init_machine = qsd8x50_init,
-	.init_late = qsd8x50_init_late,
-	.init_time	= qsd8x50_timer_init,
-MACHINE_END
-
-MACHINE_START(QSD8X50A_ST1_5, "QCT QSD8X50A ST1.5")
-	.atag_offset = 0x100,
-	.map_io = qsd8x50_map_io,
-	.init_irq = qsd8x50_init_irq,
-	.init_machine = qsd8x50_init,
-	.init_late = qsd8x50_init_late,
-	.init_time	= qsd8x50_timer_init,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-sapphire.c b/arch/arm/mach-msm/board-sapphire.c
deleted file mode 100644
index e509679..0000000
--- a/arch/arm/mach-msm/board-sapphire.c
+++ /dev/null
@@ -1,114 +0,0 @@
-/* linux/arch/arm/mach-msm/board-sapphire.c
- * Copyright (C) 2007-2009 HTC Corporation.
- * Author: Thomas Tsai <thomas_tsai@htc.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
-*/
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/device.h>
-
-#include <linux/delay.h>
-
-#include <mach/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <mach/vreg.h>
-
-#include <asm/io.h>
-#include <asm/delay.h>
-#include <asm/setup.h>
-
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/memblock.h>
-
-#include "gpio_chip.h"
-#include "board-sapphire.h"
-#include "proc_comm.h"
-#include "devices.h"
-#include "common.h"
-
-void msm_init_irq(void);
-void msm_init_gpio(void);
-
-static struct platform_device *devices[] __initdata = {
-	&msm_device_smd,
-	&msm_device_dmov,
-	&msm_device_nand,
-	&msm_device_uart1,
-	&msm_device_uart3,
-};
-
-void msm_timer_init(void);
-
-static void __init sapphire_init_irq(void)
-{
-	msm_init_irq();
-}
-
-static void __init sapphire_init(void)
-{
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-static struct map_desc sapphire_io_desc[] __initdata = {
-	{
-		.virtual = SAPPHIRE_CPLD_BASE,
-		.pfn     = __phys_to_pfn(SAPPHIRE_CPLD_START),
-		.length  = SAPPHIRE_CPLD_SIZE,
-		.type    = MT_DEVICE_NONSHARED
-	}
-};
-
-static void __init sapphire_fixup(struct tag *tags, char **cmdline)
-{
-	int smi_sz = parse_tag_smi((const struct tag *)tags);
-
-	if (smi_sz == 32) {
-		memblock_add(PHYS_OFFSET, 84*SZ_1M);
-	} else if (smi_sz == 64) {
-		memblock_add(PHYS_OFFSET, 101*SZ_1M);
-	} else {
-		memblock_add(PHYS_OFFSET, 101*SZ_1M);
-		/* Give a default value when not get smi size */
-		smi_sz = 64;
-	}
-}
-
-static void __init sapphire_map_io(void)
-{
-	msm_map_common_io();
-	iotable_init(sapphire_io_desc, ARRAY_SIZE(sapphire_io_desc));
-	msm_clock_init();
-}
-
-static void __init sapphire_init_late(void)
-{
-	smd_debugfs_init();
-}
-
-MACHINE_START(SAPPHIRE, "sapphire")
-/* Maintainer: Brian Swetland <swetland@google.com> */
-	.atag_offset    = 0x100,
-	.fixup          = sapphire_fixup,
-	.map_io         = sapphire_map_io,
-	.init_irq       = sapphire_init_irq,
-	.init_machine   = sapphire_init,
-	.init_late      = sapphire_init_late,
-	.init_time	= msm_timer_init,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
deleted file mode 100644
index 722ad63..0000000
--- a/arch/arm/mach-msm/board-trout-gpio.c
+++ /dev/null
@@ -1,233 +0,0 @@
-/*
- * linux/arch/arm/mach-msm/gpio.c
- *
- * Copyright (C) 2005 HP Labs
- * Copyright (C) 2008 Google, Inc.
- * Copyright (C) 2009 Pavel Machek <pavel@ucw.cz>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/gpio.h>
-
-#include "board-trout.h"
-
-static uint8_t trout_int_mask[2] = {
-	[0] = 0xff, /* mask all interrupts */
-	[1] = 0xff,
-};
-static uint8_t trout_sleep_int_mask[] = {
-	[0] = 0xff,
-	[1] = 0xff,
-};
-
-struct msm_gpio_chip {
-	struct gpio_chip	chip;
-	void __iomem		*reg;	/* Base of register bank */
-	u8			shadow;
-};
-
-#define to_msm_gpio_chip(c) container_of(c, struct msm_gpio_chip, chip)
-
-static int msm_gpiolib_get(struct gpio_chip *chip, unsigned offset)
-{
-	struct msm_gpio_chip *msm_gpio = to_msm_gpio_chip(chip);
-	unsigned mask = 1 << offset;
-
-	return !!(readb(msm_gpio->reg) & mask);
-}
-
-static void msm_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val)
-{
-	struct msm_gpio_chip *msm_gpio = to_msm_gpio_chip(chip);
-	unsigned mask = 1 << offset;
-
-	if (val)
-		msm_gpio->shadow |= mask;
-	else
-		msm_gpio->shadow &= ~mask;
-
-	writeb(msm_gpio->shadow, msm_gpio->reg);
-}
-
-static int msm_gpiolib_direction_input(struct gpio_chip *chip,
-					unsigned offset)
-{
-	msm_gpiolib_set(chip, offset, 0);
-	return 0;
-}
-
-static int msm_gpiolib_direction_output(struct gpio_chip *chip,
-					 unsigned offset, int val)
-{
-	msm_gpiolib_set(chip, offset, val);
-	return 0;
-}
-
-static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	return TROUT_GPIO_TO_INT(offset + chip->base);
-}
-
-#define TROUT_GPIO_BANK(name, reg_num, base_gpio, shadow_val)		\
-	{								\
-		.chip = {						\
-			.label		  = name,			\
-			.direction_input  = msm_gpiolib_direction_input,\
-			.direction_output = msm_gpiolib_direction_output, \
-			.get		  = msm_gpiolib_get,		\
-			.set		  = msm_gpiolib_set,		\
-			.to_irq		  = trout_gpio_to_irq,		\
-			.base		  = base_gpio,			\
-			.ngpio		  = 8,				\
-		},							\
-		.reg = reg_num + TROUT_CPLD_BASE,			\
-		.shadow = shadow_val,					\
-	}
-
-static struct msm_gpio_chip msm_gpio_banks[] = {
-#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9a00000)
-	/* H2W pins <-> UART1 */
-	TROUT_GPIO_BANK("MISC2", 0x00,   TROUT_GPIO_MISC2_BASE, 0x40),
-#else
-	/* H2W pins <-> UART3, Bluetooth <-> UART1 */
-	TROUT_GPIO_BANK("MISC2", 0x00,   TROUT_GPIO_MISC2_BASE, 0x80),
-#endif
-	/* I2C pull */
-	TROUT_GPIO_BANK("MISC3", 0x02,   TROUT_GPIO_MISC3_BASE, 0x04),
-	TROUT_GPIO_BANK("MISC4", 0x04,   TROUT_GPIO_MISC4_BASE, 0),
-	/* mmdi 32k en */
-	TROUT_GPIO_BANK("MISC5", 0x06,   TROUT_GPIO_MISC5_BASE, 0x04),
-	TROUT_GPIO_BANK("INT2", 0x08,    TROUT_GPIO_INT2_BASE,  0),
-	TROUT_GPIO_BANK("MISC1", 0x0a,   TROUT_GPIO_MISC1_BASE, 0),
-	TROUT_GPIO_BANK("VIRTUAL", 0x12, TROUT_GPIO_VIRTUAL_BASE, 0),
-};
-
-static void trout_gpio_irq_ack(struct irq_data *d)
-{
-	int bank = TROUT_INT_TO_BANK(d->irq);
-	uint8_t mask = TROUT_INT_TO_MASK(d->irq);
-	int reg = TROUT_BANK_TO_STAT_REG(bank);
-	/*printk(KERN_INFO "trout_gpio_irq_ack irq %d\n", d->irq);*/
-	writeb(mask, TROUT_CPLD_BASE + reg);
-}
-
-static void trout_gpio_irq_mask(struct irq_data *d)
-{
-	unsigned long flags;
-	uint8_t reg_val;
-	int bank = TROUT_INT_TO_BANK(d->irq);
-	uint8_t mask = TROUT_INT_TO_MASK(d->irq);
-	int reg = TROUT_BANK_TO_MASK_REG(bank);
-
-	local_irq_save(flags);
-	reg_val = trout_int_mask[bank] |= mask;
-	/*printk(KERN_INFO "trout_gpio_irq_mask irq %d => %d:%02x\n",
-	       d->irq, bank, reg_val);*/
-	writeb(reg_val, TROUT_CPLD_BASE + reg);
-	local_irq_restore(flags);
-}
-
-static void trout_gpio_irq_unmask(struct irq_data *d)
-{
-	unsigned long flags;
-	uint8_t reg_val;
-	int bank = TROUT_INT_TO_BANK(d->irq);
-	uint8_t mask = TROUT_INT_TO_MASK(d->irq);
-	int reg = TROUT_BANK_TO_MASK_REG(bank);
-
-	local_irq_save(flags);
-	reg_val = trout_int_mask[bank] &= ~mask;
-	/*printk(KERN_INFO "trout_gpio_irq_unmask irq %d => %d:%02x\n",
-	       d->irq, bank, reg_val);*/
-	writeb(reg_val, TROUT_CPLD_BASE + reg);
-	local_irq_restore(flags);
-}
-
-int trout_gpio_irq_set_wake(struct irq_data *d, unsigned int on)
-{
-	unsigned long flags;
-	int bank = TROUT_INT_TO_BANK(d->irq);
-	uint8_t mask = TROUT_INT_TO_MASK(d->irq);
-
-	local_irq_save(flags);
-	if(on)
-		trout_sleep_int_mask[bank] &= ~mask;
-	else
-		trout_sleep_int_mask[bank] |= mask;
-	local_irq_restore(flags);
-	return 0;
-}
-
-static void trout_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	int j, m;
-	unsigned v;
-	int bank;
-	int stat_reg;
-	int int_base = TROUT_INT_START;
-	uint8_t int_mask;
-
-	for (bank = 0; bank < 2; bank++) {
-		stat_reg = TROUT_BANK_TO_STAT_REG(bank);
-		v = readb(TROUT_CPLD_BASE + stat_reg);
-		int_mask = trout_int_mask[bank];
-		if (v & int_mask) {
-			writeb(v & int_mask, TROUT_CPLD_BASE + stat_reg);
-			printk(KERN_ERR "trout_gpio_irq_handler: got masked "
-			       "interrupt: %d:%02x\n", bank, v & int_mask);
-		}
-		v &= ~int_mask;
-		while (v) {
-			m = v & -v;
-			j = fls(m) - 1;
-			/*printk(KERN_INFO "msm_gpio_irq_handler %d:%02x %02x b"
-			       "it %d irq %d\n", bank, v, m, j, int_base + j);*/
-			v &= ~m;
-			generic_handle_irq(int_base + j);
-		}
-		int_base += TROUT_INT_BANK0_COUNT;
-	}
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-}
-
-static struct irq_chip trout_gpio_irq_chip = {
-	.name          = "troutgpio",
-	.irq_ack       = trout_gpio_irq_ack,
-	.irq_mask      = trout_gpio_irq_mask,
-	.irq_unmask    = trout_gpio_irq_unmask,
-	.irq_set_wake  = trout_gpio_irq_set_wake,
-};
-
-/*
- * Called from the processor-specific init to enable GPIO pin support.
- */
-int __init trout_init_gpio(void)
-{
-	int i;
-	for(i = TROUT_INT_START; i <= TROUT_INT_END; i++) {
-		irq_set_chip_and_handler(i, &trout_gpio_irq_chip,
-					 handle_edge_irq);
-		set_irq_flags(i, IRQF_VALID);
-	}
-
-	for (i = 0; i < ARRAY_SIZE(msm_gpio_banks); i++)
-		gpiochip_add(&msm_gpio_banks[i].chip);
-
-	irq_set_irq_type(MSM_GPIO_TO_INT(17), IRQF_TRIGGER_HIGH);
-	irq_set_chained_handler(MSM_GPIO_TO_INT(17), trout_gpio_irq_handler);
-	irq_set_irq_wake(MSM_GPIO_TO_INT(17), 1);
-
-	return 0;
-}
-
-postcore_initcall(trout_init_gpio);
-
diff --git a/arch/arm/mach-msm/board-trout-mmc.c b/arch/arm/mach-msm/board-trout-mmc.c
deleted file mode 100644
index 3723e55..0000000
--- a/arch/arm/mach-msm/board-trout-mmc.c
+++ /dev/null
@@ -1,185 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout-mmc.c
-** Author: Brian Swetland <swetland@google.com>
-*/
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/sdio_ids.h>
-#include <linux/err.h>
-#include <linux/debugfs.h>
-
-#include <asm/io.h>
-
-#include <mach/vreg.h>
-
-#include <linux/platform_data/mmc-msm_sdcc.h>
-
-#include "devices.h"
-
-#include "board-trout.h"
-
-#include "proc_comm.h"
-
-#define DEBUG_SDSLOT_VDD 1
-
-/* ---- COMMON ---- */
-static void config_gpio_table(uint32_t *table, int len)
-{
-	int n;
-	unsigned id;
-	for(n = 0; n < len; n++) {
-		id = table[n];
-		msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &id, 0);
-	}
-}
-
-/* ---- SDCARD ---- */
-
-static uint32_t sdcard_on_gpio_table[] = {
-	PCOM_GPIO_CFG(62, 2, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_8MA), /* CLK */
-	PCOM_GPIO_CFG(63, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* CMD */
-	PCOM_GPIO_CFG(64, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* DAT3 */
-	PCOM_GPIO_CFG(65, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_8MA), /* DAT2 */
-	PCOM_GPIO_CFG(66, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT1 */
-	PCOM_GPIO_CFG(67, 2, GPIO_OUTPUT, GPIO_PULL_UP, GPIO_4MA), /* DAT0 */
-};
-
-static uint32_t sdcard_off_gpio_table[] = {
-	PCOM_GPIO_CFG(62, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CLK */
-	PCOM_GPIO_CFG(63, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* CMD */
-	PCOM_GPIO_CFG(64, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT3 */
-	PCOM_GPIO_CFG(65, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT2 */
-	PCOM_GPIO_CFG(66, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT1 */
-	PCOM_GPIO_CFG(67, 0, GPIO_OUTPUT, GPIO_NO_PULL, GPIO_4MA), /* DAT0 */
-};
-
-static uint opt_disable_sdcard;
-
-static int __init trout_disablesdcard_setup(char *str)
-{
-	int cal = simple_strtol(str, NULL, 0);
-	
-	opt_disable_sdcard = cal;
-	return 1;
-}
-
-__setup("board_trout.disable_sdcard=", trout_disablesdcard_setup);
-
-static struct vreg *vreg_sdslot;	/* SD slot power */
-
-struct mmc_vdd_xlat {
-	int mask;
-	int level;
-};
-
-static struct mmc_vdd_xlat mmc_vdd_table[] = {
-	{ MMC_VDD_165_195,	1800 },
-	{ MMC_VDD_20_21,	2050 },
-	{ MMC_VDD_21_22,	2150 },
-	{ MMC_VDD_22_23,	2250 },
-	{ MMC_VDD_23_24,	2350 },
-	{ MMC_VDD_24_25,	2450 },
-	{ MMC_VDD_25_26,	2550 },
-	{ MMC_VDD_26_27,	2650 },
-	{ MMC_VDD_27_28,	2750 },
-	{ MMC_VDD_28_29,	2850 },
-	{ MMC_VDD_29_30,	2950 },
-};
-
-static unsigned int sdslot_vdd = 0xffffffff;
-static unsigned int sdslot_vreg_enabled;
-
-static uint32_t trout_sdslot_switchvdd(struct device *dev, unsigned int vdd)
-{
-	int i, rc;
-
-	BUG_ON(!vreg_sdslot);
-
-	if (vdd == sdslot_vdd)
-		return 0;
-
-	sdslot_vdd = vdd;
-
-	if (vdd == 0) {
-#if DEBUG_SDSLOT_VDD
-		printk("%s: Disabling SD slot power\n", __func__);
-#endif
-		config_gpio_table(sdcard_off_gpio_table,
-				  ARRAY_SIZE(sdcard_off_gpio_table));
-		vreg_disable(vreg_sdslot);
-		sdslot_vreg_enabled = 0;
-		return 0;
-	}
-
-	if (!sdslot_vreg_enabled) {
-		rc = vreg_enable(vreg_sdslot);
-		if (rc) {
-			printk(KERN_ERR "%s: Error enabling vreg (%d)\n",
-			       __func__, rc);
-		}
-		config_gpio_table(sdcard_on_gpio_table,
-				  ARRAY_SIZE(sdcard_on_gpio_table));
-		sdslot_vreg_enabled = 1;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(mmc_vdd_table); i++) {
-		if (mmc_vdd_table[i].mask == (1 << vdd)) {
-#if DEBUG_SDSLOT_VDD
-			printk("%s: Setting level to %u\n",
-			        __func__, mmc_vdd_table[i].level);
-#endif
-			rc = vreg_set_level(vreg_sdslot,
-					    mmc_vdd_table[i].level);
-			if (rc) {
-				printk(KERN_ERR
-				       "%s: Error setting vreg level (%d)\n",
-				       __func__, rc);
-			}
-			return 0;
-		}
-	}
-
-	printk(KERN_ERR "%s: Invalid VDD %d specified\n", __func__, vdd);
-	return 0;
-}
-
-static unsigned int trout_sdslot_status(struct device *dev)
-{
-	unsigned int status;
-
-	status = (unsigned int) gpio_get_value(TROUT_GPIO_SDMC_CD_N);
-	return (!status);
-}
-
-#define TROUT_MMC_VDD	MMC_VDD_165_195 | MMC_VDD_20_21 | MMC_VDD_21_22 \
-			| MMC_VDD_22_23 | MMC_VDD_23_24 | MMC_VDD_24_25 \
-			| MMC_VDD_25_26 | MMC_VDD_26_27 | MMC_VDD_27_28 \
-			| MMC_VDD_28_29 | MMC_VDD_29_30
-
-static struct msm_mmc_platform_data trout_sdslot_data = {
-	.ocr_mask	= TROUT_MMC_VDD,
-	.status		= trout_sdslot_status,
-	.translate_vdd	= trout_sdslot_switchvdd,
-};
-
-int __init trout_init_mmc(unsigned int sys_rev)
-{
-	sdslot_vreg_enabled = 0;
-
-	vreg_sdslot = vreg_get(0, "gp6");
-	if (IS_ERR(vreg_sdslot))
-		return PTR_ERR(vreg_sdslot);
-
-	irq_set_irq_wake(TROUT_GPIO_TO_INT(TROUT_GPIO_SDMC_CD_N), 1);
-
-	if (!opt_disable_sdcard)
-		msm_add_sdcc(2, &trout_sdslot_data,
-			     TROUT_GPIO_TO_INT(TROUT_GPIO_SDMC_CD_N), 0);
-	else
-		printk(KERN_INFO "trout: SD-Card interface disabled\n");
-	return 0;
-}
-
diff --git a/arch/arm/mach-msm/board-trout-panel.c b/arch/arm/mach-msm/board-trout-panel.c
deleted file mode 100644
index 77b0a26..0000000
--- a/arch/arm/mach-msm/board-trout-panel.c
+++ /dev/null
@@ -1,292 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout-mddi.c
-** Author: Brian Swetland <swetland@google.com>
-*/
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/leds.h>
-#include <linux/err.h>
-
-#include <asm/io.h>
-#include <asm/mach-types.h>
-#include <asm/system_info.h>
-
-#include <linux/platform_data/video-msm_fb.h>
-#include <mach/vreg.h>
-
-#include "board-trout.h"
-#include "proc_comm.h"
-#include "clock-pcom.h"
-#include "devices.h"
-
-#define TROUT_DEFAULT_BACKLIGHT_BRIGHTNESS 255
-
-#define MDDI_CLIENT_CORE_BASE  0x108000
-#define LCD_CONTROL_BLOCK_BASE 0x110000
-#define SPI_BLOCK_BASE         0x120000
-#define I2C_BLOCK_BASE         0x130000
-#define PWM_BLOCK_BASE         0x140000
-#define GPIO_BLOCK_BASE        0x150000
-#define SYSTEM_BLOCK1_BASE     0x160000
-#define SYSTEM_BLOCK2_BASE     0x170000
-
-
-#define	DPSUS       (MDDI_CLIENT_CORE_BASE|0x24)
-#define	SYSCLKENA   (MDDI_CLIENT_CORE_BASE|0x2C)
-#define	PWM0OFF	      (PWM_BLOCK_BASE|0x1C)
-
-#define V_VDDE2E_VDD2_GPIO 0
-#define MDDI_RST_N 82
-
-#define	MDDICAP0    (MDDI_CLIENT_CORE_BASE|0x00)
-#define	MDDICAP1    (MDDI_CLIENT_CORE_BASE|0x04)
-#define	MDDICAP2    (MDDI_CLIENT_CORE_BASE|0x08)
-#define	MDDICAP3    (MDDI_CLIENT_CORE_BASE|0x0C)
-#define	MDCAPCHG    (MDDI_CLIENT_CORE_BASE|0x10)
-#define	MDCRCERC    (MDDI_CLIENT_CORE_BASE|0x14)
-#define	TTBUSSEL    (MDDI_CLIENT_CORE_BASE|0x18)
-#define	DPSET0      (MDDI_CLIENT_CORE_BASE|0x1C)
-#define	DPSET1      (MDDI_CLIENT_CORE_BASE|0x20)
-#define	DPSUS       (MDDI_CLIENT_CORE_BASE|0x24)
-#define	DPRUN       (MDDI_CLIENT_CORE_BASE|0x28)
-#define	SYSCKENA    (MDDI_CLIENT_CORE_BASE|0x2C)
-#define	TESTMODE    (MDDI_CLIENT_CORE_BASE|0x30)
-#define	FIFOMONI    (MDDI_CLIENT_CORE_BASE|0x34)
-#define	INTMONI     (MDDI_CLIENT_CORE_BASE|0x38)
-#define	MDIOBIST    (MDDI_CLIENT_CORE_BASE|0x3C)
-#define	MDIOPSET    (MDDI_CLIENT_CORE_BASE|0x40)
-#define	BITMAP0     (MDDI_CLIENT_CORE_BASE|0x44)
-#define	BITMAP1     (MDDI_CLIENT_CORE_BASE|0x48)
-#define	BITMAP2     (MDDI_CLIENT_CORE_BASE|0x4C)
-#define	BITMAP3     (MDDI_CLIENT_CORE_BASE|0x50)
-#define	BITMAP4     (MDDI_CLIENT_CORE_BASE|0x54)
-
-#define	SRST        (LCD_CONTROL_BLOCK_BASE|0x00)
-#define	PORT_ENB    (LCD_CONTROL_BLOCK_BASE|0x04)
-#define	START       (LCD_CONTROL_BLOCK_BASE|0x08)
-#define	PORT        (LCD_CONTROL_BLOCK_BASE|0x0C)
-#define	CMN         (LCD_CONTROL_BLOCK_BASE|0x10)
-#define	GAMMA       (LCD_CONTROL_BLOCK_BASE|0x14)
-#define	INTFLG      (LCD_CONTROL_BLOCK_BASE|0x18)
-#define	INTMSK      (LCD_CONTROL_BLOCK_BASE|0x1C)
-#define	MPLFBUF     (LCD_CONTROL_BLOCK_BASE|0x20)
-#define	HDE_LEFT    (LCD_CONTROL_BLOCK_BASE|0x24)
-#define	VDE_TOP     (LCD_CONTROL_BLOCK_BASE|0x28)
-#define	PXL         (LCD_CONTROL_BLOCK_BASE|0x30)
-#define	HCYCLE      (LCD_CONTROL_BLOCK_BASE|0x34)
-#define	HSW         (LCD_CONTROL_BLOCK_BASE|0x38)
-#define	HDE_START   (LCD_CONTROL_BLOCK_BASE|0x3C)
-#define	HDE_SIZE    (LCD_CONTROL_BLOCK_BASE|0x40)
-#define	VCYCLE      (LCD_CONTROL_BLOCK_BASE|0x44)
-#define	VSW         (LCD_CONTROL_BLOCK_BASE|0x48)
-#define	VDE_START   (LCD_CONTROL_BLOCK_BASE|0x4C)
-#define	VDE_SIZE    (LCD_CONTROL_BLOCK_BASE|0x50)
-#define	WAKEUP      (LCD_CONTROL_BLOCK_BASE|0x54)
-#define	WSYN_DLY    (LCD_CONTROL_BLOCK_BASE|0x58)
-#define	REGENB      (LCD_CONTROL_BLOCK_BASE|0x5C)
-#define	VSYNIF      (LCD_CONTROL_BLOCK_BASE|0x60)
-#define	WRSTB       (LCD_CONTROL_BLOCK_BASE|0x64)
-#define	RDSTB       (LCD_CONTROL_BLOCK_BASE|0x68)
-#define	ASY_DATA    (LCD_CONTROL_BLOCK_BASE|0x6C)
-#define	ASY_DATB    (LCD_CONTROL_BLOCK_BASE|0x70)
-#define	ASY_DATC    (LCD_CONTROL_BLOCK_BASE|0x74)
-#define	ASY_DATD    (LCD_CONTROL_BLOCK_BASE|0x78)
-#define	ASY_DATE    (LCD_CONTROL_BLOCK_BASE|0x7C)
-#define	ASY_DATF    (LCD_CONTROL_BLOCK_BASE|0x80)
-#define	ASY_DATG    (LCD_CONTROL_BLOCK_BASE|0x84)
-#define	ASY_DATH    (LCD_CONTROL_BLOCK_BASE|0x88)
-#define	ASY_CMDSET  (LCD_CONTROL_BLOCK_BASE|0x8C)
-
-#define	SSICTL      (SPI_BLOCK_BASE|0x00)
-#define	SSITIME     (SPI_BLOCK_BASE|0x04)
-#define	SSITX       (SPI_BLOCK_BASE|0x08)
-#define	SSIRX       (SPI_BLOCK_BASE|0x0C)
-#define	SSIINTC     (SPI_BLOCK_BASE|0x10)
-#define	SSIINTS     (SPI_BLOCK_BASE|0x14)
-#define	SSIDBG1     (SPI_BLOCK_BASE|0x18)
-#define	SSIDBG2     (SPI_BLOCK_BASE|0x1C)
-#define	SSIID       (SPI_BLOCK_BASE|0x20)
-
-#define	WKREQ       (SYSTEM_BLOCK1_BASE|0x00)
-#define	CLKENB      (SYSTEM_BLOCK1_BASE|0x04)
-#define	DRAMPWR     (SYSTEM_BLOCK1_BASE|0x08)
-#define	INTMASK     (SYSTEM_BLOCK1_BASE|0x0C)
-#define	GPIOSEL     (SYSTEM_BLOCK2_BASE|0x00)
-
-#define	GPIODATA    (GPIO_BLOCK_BASE|0x00)
-#define	GPIODIR     (GPIO_BLOCK_BASE|0x04)
-#define	GPIOIS      (GPIO_BLOCK_BASE|0x08)
-#define	GPIOIBE     (GPIO_BLOCK_BASE|0x0C)
-#define	GPIOIEV     (GPIO_BLOCK_BASE|0x10)
-#define	GPIOIE      (GPIO_BLOCK_BASE|0x14)
-#define	GPIORIS     (GPIO_BLOCK_BASE|0x18)
-#define	GPIOMIS     (GPIO_BLOCK_BASE|0x1C)
-#define	GPIOIC      (GPIO_BLOCK_BASE|0x20)
-#define	GPIOOMS     (GPIO_BLOCK_BASE|0x24)
-#define	GPIOPC      (GPIO_BLOCK_BASE|0x28)
-#define	GPIOID      (GPIO_BLOCK_BASE|0x30)
-
-#define SPI_WRITE(reg, val) \
-	{ SSITX,        0x00010000 | (((reg) & 0xff) << 8) | ((val) & 0xff) }, \
-	{ 0, 5 },
-
-#define SPI_WRITE1(reg) \
-	{ SSITX,        (reg) & 0xff }, \
-	{ 0, 5 },
-
-struct mddi_table {
-	uint32_t reg;
-	uint32_t value;
-};
-static struct mddi_table mddi_toshiba_init_table[] = {
-	{ DPSET0,       0x09e90046 },
-	{ DPSET1,       0x00000118 },
-	{ DPSUS,        0x00000000 },
-	{ DPRUN,        0x00000001 },
-	{ 1,            14         }, /* msleep 14 */
-	{ SYSCKENA,     0x00000001 },
-	{ CLKENB,       0x0000A1EF },  /*    # SYS.CLKENB  # Enable clocks for each module (without DCLK , i2cCLK) */
-
-	{ GPIODATA,     0x02000200 },  /*   # GPI .GPIODATA  # GPIO2(RESET_LCD_N) set to 0 , GPIO3(eDRAM_Power) set to 0 */
-	{ GPIODIR,      0x000030D  },  /* 24D   # GPI .GPIODIR  # Select direction of GPIO port (0,2,3,6,9 output) */
-	{ GPIOSEL,      0/*0x00000173*/},  /*   # SYS.GPIOSEL  # GPIO port multiplexing control */
-	{ GPIOPC,       0x03C300C0 },  /*   # GPI .GPIOPC  # GPIO2,3 PD cut */
-	{ WKREQ,        0x00000000 },  /*   # SYS.WKREQ  # Wake-up request event is VSYNC alignment */
-
-	{ GPIOIBE,      0x000003FF },
-	{ GPIOIS,       0x00000000 },
-	{ GPIOIC,       0x000003FF },
-	{ GPIOIE,       0x00000000 },
-
-	{ GPIODATA,     0x00040004 },  /*   # GPI .GPIODATA  # eDRAM VD supply */
-	{ 1,            1          }, /* msleep 1 */
-	{ GPIODATA,     0x02040004 },  /*   # GPI .GPIODATA  # eDRAM VD supply */
-	{ DRAMPWR,      0x00000001 }, /* eDRAM power */
-};
-
-#define GPIOSEL_VWAKEINT (1U << 0)
-#define INTMASK_VWAKEOUT (1U << 0)
-
-
-static int trout_new_backlight = 1;
-static struct vreg *vreg_mddi_1v5;
-static struct vreg *vreg_lcm_2v85;
-
-static void trout_process_mddi_table(struct msm_mddi_client_data *client_data,
-				     struct mddi_table *table, size_t count)
-{
-	int i;
-	for (i = 0; i < count; i++) {
-		uint32_t reg = table[i].reg;
-		uint32_t value = table[i].value;
-
-		if (reg == 0)
-			udelay(value);
-		else if (reg == 1)
-			msleep(value);
-		else
-			client_data->remote_write(client_data, value, reg);
-	}
-}
-
-static int trout_mddi_toshiba_client_init(
-	struct msm_mddi_bridge_platform_data *bridge_data,
-	struct msm_mddi_client_data *client_data)
-{
-	int panel_id;
-
-	client_data->auto_hibernate(client_data, 0);
-	trout_process_mddi_table(client_data, mddi_toshiba_init_table,
-				 ARRAY_SIZE(mddi_toshiba_init_table));
-	client_data->auto_hibernate(client_data, 1);
-	panel_id = (client_data->remote_read(client_data, GPIODATA) >> 4) & 3;
-	if (panel_id > 1) {
-		printk(KERN_WARNING "unknown panel id at mddi_enable\n");
-		return -1;
-	}
-	return 0;
-}
-
-static int trout_mddi_toshiba_client_uninit(
-	struct msm_mddi_bridge_platform_data *bridge_data,
-	struct msm_mddi_client_data *client_data)
-{
-	return 0;
-}
-
-static struct resource resources_msm_fb[] = {
-	{
-		.start = MSM_FB_BASE,
-		.end = MSM_FB_BASE + MSM_FB_SIZE,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-struct msm_mddi_bridge_platform_data toshiba_client_data = {
-	.init = trout_mddi_toshiba_client_init,
-	.uninit = trout_mddi_toshiba_client_uninit,
-	.fb_data = {
-		.xres = 320,
-		.yres = 480,
-		.width = 45,
-		.height = 67,
-		.output_format = 0,
-	},
-};
-
-static struct msm_mddi_platform_data mddi_pdata = {
-	.clk_rate = 122880000,
-	.fb_resource = resources_msm_fb,
-	.num_clients = 1,
-	.client_platform_data = {
-		{
-			.product_id = (0xd263 << 16 | 0),
-			.name = "mddi_c_d263_0000",
-			.id = 0,
-			.client_data = &toshiba_client_data,
-			.clk_rate = 0,
-		},
-	},
-};
-
-int __init trout_init_panel(void)
-{
-	int rc;
-
-	if (!machine_is_trout())
-		return 0;
-	vreg_mddi_1v5 = vreg_get(0, "gp2");
-	if (IS_ERR(vreg_mddi_1v5))
-		return PTR_ERR(vreg_mddi_1v5);
-	vreg_lcm_2v85 = vreg_get(0, "gp4");
-	if (IS_ERR(vreg_lcm_2v85))
-		return PTR_ERR(vreg_lcm_2v85);
-
-	trout_new_backlight = system_rev >= 5;
-	if (trout_new_backlight) {
-		uint32_t config = PCOM_GPIO_CFG(27, 0, GPIO_OUTPUT,
-						GPIO_NO_PULL, GPIO_8MA);
-		msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &config, 0);
-	} else {
-		uint32_t config = PCOM_GPIO_CFG(27, 1, GPIO_OUTPUT,
-						GPIO_NO_PULL, GPIO_8MA);
-		uint32_t id = P_GP_CLK;
-		uint32_t rate = 19200000;
-
-		msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX, &config, 0);
-
-		msm_proc_comm(PCOM_CLKCTL_RPC_SET_RATE, &id, &rate);
-		if (id < 0)
-			pr_err("trout_init_panel: set clock rate failed\n");
-	}
-
-	rc = platform_device_register(&msm_device_mdp);
-	if (rc)
-		return rc;
-	msm_device_mddi0.dev.platform_data = &mddi_pdata;
-	return platform_device_register(&msm_device_mddi0);
-}
-
-device_initcall(trout_init_panel);
diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
deleted file mode 100644
index ba3edd3..0000000
--- a/arch/arm/mach-msm/board-trout.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout.c
- *
- * Copyright (C) 2009 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-#define pr_fmt(fmt) "%s: " fmt, __func__
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/clkdev.h>
-#include <linux/memblock.h>
-
-#include <asm/system_info.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/setup.h>
-
-#include <mach/hardware.h>
-#include <mach/msm_iomap.h>
-
-#include "devices.h"
-#include "board-trout.h"
-#include "common.h"
-
-extern int trout_init_mmc(unsigned int);
-
-static struct platform_device *devices[] __initdata = {
-	&msm_clock_7x01a,
-	&msm_device_gpio_7201,
-	&msm_device_uart3,
-	&msm_device_smd,
-	&msm_device_nand,
-	&msm_device_hsusb,
-	&msm_device_i2c,
-};
-
-static void __init trout_init_early(void)
-{
-	arch_ioremap_caller = __msm_ioremap_caller;
-}
-
-static void __init trout_init_irq(void)
-{
-	msm_init_irq();
-}
-
-static void __init trout_fixup(struct tag *tags, char **cmdline)
-{
-	memblock_add(PHYS_OFFSET, 101*SZ_1M);
-}
-
-static void __init trout_init(void)
-{
-	int rc;
-
-	platform_add_devices(devices, ARRAY_SIZE(devices));
-
-	if (IS_ENABLED(CONFIG_MMC)) {
-		rc = trout_init_mmc(system_rev);
-		if (rc)
-			pr_crit("MMC init failure (%d)\n", rc);
-	}
-}
-
-static struct map_desc trout_io_desc[] __initdata = {
-	{
-		.virtual = (unsigned long)TROUT_CPLD_BASE,
-		.pfn     = __phys_to_pfn(TROUT_CPLD_START),
-		.length  = TROUT_CPLD_SIZE,
-		.type    = MT_DEVICE_NONSHARED
-	}
-};
-
-static void __init trout_map_io(void)
-{
-	msm_map_common_io();
-	iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
-
-#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9c00000)
-	/* route UART3 to the "H2W" extended usb connector */
-	writeb(0x80, TROUT_CPLD_BASE + 0x00);
-#endif
-}
-
-static void __init trout_init_late(void)
-{
-	smd_debugfs_init();
-}
-
-MACHINE_START(TROUT, "HTC Dream")
-	.atag_offset	= 0x100,
-	.fixup		= trout_fixup,
-	.map_io		= trout_map_io,
-	.init_early	= trout_init_early,
-	.init_irq	= trout_init_irq,
-	.init_machine	= trout_init,
-	.init_late	= trout_init_late,
-	.init_time	= msm7x01_timer_init,
-MACHINE_END
diff --git a/arch/arm/mach-msm/board-trout.h b/arch/arm/mach-msm/board-trout.h
deleted file mode 100644
index adb757a..0000000
--- a/arch/arm/mach-msm/board-trout.h
+++ /dev/null
@@ -1,162 +0,0 @@
-/* linux/arch/arm/mach-msm/board-trout.h
-** Author: Brian Swetland <swetland@google.com>
-*/
-#ifndef __ARCH_ARM_MACH_MSM_BOARD_TROUT_H
-#define __ARCH_ARM_MACH_MSM_BOARD_TROUT_H
-
-#include "common.h"
-
-#define MSM_SMI_BASE		0x00000000
-#define MSM_SMI_SIZE		0x00800000
-
-#define MSM_EBI_BASE		0x10000000
-#define MSM_EBI_SIZE		0x06e00000
-
-#define MSM_PMEM_GPU0_BASE	0x00000000
-#define MSM_PMEM_GPU0_SIZE	0x00700000
-
-#define MSM_PMEM_MDP_BASE	0x02000000
-#define MSM_PMEM_MDP_SIZE	0x00800000
-
-#define MSM_PMEM_ADSP_BASE      0x02800000
-#define MSM_PMEM_ADSP_SIZE	0x00800000
-
-#define MSM_PMEM_CAMERA_BASE	0x03000000
-#define MSM_PMEM_CAMERA_SIZE	0x00800000
-
-#define MSM_FB_BASE		0x03800000
-#define MSM_FB_SIZE		0x00100000
-
-#define MSM_LINUX_BASE		MSM_EBI_BASE
-#define MSM_LINUX_SIZE		0x06500000
-
-#define MSM_PMEM_GPU1_SIZE	0x800000
-#define MSM_PMEM_GPU1_BASE	(MSM_RAM_CONSOLE_BASE - MSM_PMEM_GPU1_SIZE)
-
-#define MSM_RAM_CONSOLE_BASE	(MSM_EBI_BASE + 0x6d00000)
-#define MSM_RAM_CONSOLE_SIZE	(128 * SZ_1K)
-
-#if (MSM_FB_BASE + MSM_FB_SIZE) >= (MSM_PMEM_GPU1_BASE)
-#error invalid memory map
-#endif
-
-#define DECLARE_MSM_IOMAP
-#include <mach/msm_iomap.h>
-
-#define TROUT_4_BALL_UP_0     1
-#define TROUT_4_BALL_LEFT_0   18
-#define TROUT_4_BALL_DOWN_0   57
-#define TROUT_4_BALL_RIGHT_0  91
-
-#define TROUT_5_BALL_UP_0     94
-#define TROUT_5_BALL_LEFT_0   18
-#define TROUT_5_BALL_DOWN_0   90
-#define TROUT_5_BALL_RIGHT_0  19
-
-#define TROUT_POWER_KEY     20
-
-#define TROUT_4_TP_LS_EN    19
-#define TROUT_5_TP_LS_EN    1
-
-#define TROUT_CPLD_BASE   IOMEM(0xE8100000)
-#define TROUT_CPLD_START  0x98000000
-#define TROUT_CPLD_SIZE   SZ_4K
-
-#define TROUT_GPIO_CABLE_IN1		(83)
-#define TROUT_GPIO_CABLE_IN2		(49)
-
-#define TROUT_GPIO_START (128)
-
-#define TROUT_GPIO_INT_MASK0_REG            (0x0c)
-#define TROUT_GPIO_INT_STAT0_REG            (0x0e)
-#define TROUT_GPIO_INT_MASK1_REG            (0x14)
-#define TROUT_GPIO_INT_STAT1_REG            (0x10)
-
-#define TROUT_GPIO_HAPTIC_PWM               (28)
-#define TROUT_GPIO_PS_HOLD                  (25)
-
-#define TROUT_GPIO_MISC2_BASE               (TROUT_GPIO_START + 0x00)
-#define TROUT_GPIO_MISC3_BASE               (TROUT_GPIO_START + 0x08)
-#define TROUT_GPIO_MISC4_BASE               (TROUT_GPIO_START + 0x10)
-#define TROUT_GPIO_MISC5_BASE               (TROUT_GPIO_START + 0x18)
-#define TROUT_GPIO_INT2_BASE                (TROUT_GPIO_START + 0x20)
-#define TROUT_GPIO_MISC1_BASE               (TROUT_GPIO_START + 0x28)
-#define TROUT_GPIO_VIRTUAL_BASE             (TROUT_GPIO_START + 0x30)
-#define TROUT_GPIO_INT5_BASE                (TROUT_GPIO_START + 0x48)
-
-#define TROUT_GPIO_CHARGER_EN               (TROUT_GPIO_MISC2_BASE + 0)
-#define TROUT_GPIO_ISET                     (TROUT_GPIO_MISC2_BASE + 1)
-#define TROUT_GPIO_H2W_DAT_DIR              (TROUT_GPIO_MISC2_BASE + 2)
-#define TROUT_GPIO_H2W_CLK_DIR              (TROUT_GPIO_MISC2_BASE + 3)
-#define TROUT_GPIO_H2W_DAT_GPO              (TROUT_GPIO_MISC2_BASE + 4)
-#define TROUT_GPIO_H2W_CLK_GPO              (TROUT_GPIO_MISC2_BASE + 5)
-#define TROUT_GPIO_H2W_SEL0                 (TROUT_GPIO_MISC2_BASE + 6)
-#define TROUT_GPIO_H2W_SEL1                 (TROUT_GPIO_MISC2_BASE + 7)
-
-#define TROUT_GPIO_SPOTLIGHT_EN             (TROUT_GPIO_MISC3_BASE + 0)
-#define TROUT_GPIO_FLASH_EN                 (TROUT_GPIO_MISC3_BASE + 1)
-#define TROUT_GPIO_I2C_PULL                 (TROUT_GPIO_MISC3_BASE + 2)
-#define TROUT_GPIO_TP_I2C_PULL              (TROUT_GPIO_MISC3_BASE + 3)
-#define TROUT_GPIO_TP_EN                    (TROUT_GPIO_MISC3_BASE + 4)
-#define TROUT_GPIO_JOG_EN                   (TROUT_GPIO_MISC3_BASE + 5)
-#define TROUT_GPIO_UI_LED_EN                (TROUT_GPIO_MISC3_BASE + 6)
-#define TROUT_GPIO_QTKEY_LED_EN             (TROUT_GPIO_MISC3_BASE + 7)
-
-#define TROUT_GPIO_VCM_PWDN                 (TROUT_GPIO_MISC4_BASE + 0)
-#define TROUT_GPIO_USB_H2W_SW               (TROUT_GPIO_MISC4_BASE + 1)
-#define TROUT_GPIO_COMPASS_RST_N            (TROUT_GPIO_MISC4_BASE + 2)
-#define TROUT_GPIO_HAPTIC_EN_UP             (TROUT_GPIO_MISC4_BASE + 3)
-#define TROUT_GPIO_HAPTIC_EN_MAIN           (TROUT_GPIO_MISC4_BASE + 4)
-#define TROUT_GPIO_USB_PHY_RST_N            (TROUT_GPIO_MISC4_BASE + 5)
-#define TROUT_GPIO_WIFI_PA_RESETX           (TROUT_GPIO_MISC4_BASE + 6)
-#define TROUT_GPIO_WIFI_EN                  (TROUT_GPIO_MISC4_BASE + 7)
-
-#define TROUT_GPIO_BT_32K_EN                (TROUT_GPIO_MISC5_BASE + 0)
-#define TROUT_GPIO_MAC_32K_EN               (TROUT_GPIO_MISC5_BASE + 1)
-#define TROUT_GPIO_MDDI_32K_EN              (TROUT_GPIO_MISC5_BASE + 2)
-#define TROUT_GPIO_COMPASS_32K_EN           (TROUT_GPIO_MISC5_BASE + 3)
-
-#define TROUT_GPIO_NAVI_ACT_N               (TROUT_GPIO_INT2_BASE + 0)
-#define TROUT_GPIO_COMPASS_IRQ              (TROUT_GPIO_INT2_BASE + 1)
-#define TROUT_GPIO_SLIDING_DET              (TROUT_GPIO_INT2_BASE + 2)
-#define TROUT_GPIO_AUD_HSMIC_DET_N          (TROUT_GPIO_INT2_BASE + 3)
-#define TROUT_GPIO_SD_DOOR_N                (TROUT_GPIO_INT2_BASE + 4)
-#define TROUT_GPIO_CAM_BTN_STEP1_N          (TROUT_GPIO_INT2_BASE + 5)
-#define TROUT_GPIO_CAM_BTN_STEP2_N          (TROUT_GPIO_INT2_BASE + 6)
-#define TROUT_GPIO_TP_ATT_N                 (TROUT_GPIO_INT2_BASE + 7)
-#define TROUT_GPIO_BANK0_FIRST_INT_SOURCE   (TROUT_GPIO_NAVI_ACT_N)
-#define TROUT_GPIO_BANK0_LAST_INT_SOURCE    (TROUT_GPIO_TP_ATT_N)
-
-#define TROUT_GPIO_H2W_DAT_GPI              (TROUT_GPIO_MISC1_BASE + 0)
-#define TROUT_GPIO_H2W_CLK_GPI              (TROUT_GPIO_MISC1_BASE + 1)
-#define TROUT_GPIO_CPLD128_VER_0            (TROUT_GPIO_MISC1_BASE + 4)
-#define TROUT_GPIO_CPLD128_VER_1            (TROUT_GPIO_MISC1_BASE + 5)
-#define TROUT_GPIO_CPLD128_VER_2            (TROUT_GPIO_MISC1_BASE + 6)
-#define TROUT_GPIO_CPLD128_VER_3            (TROUT_GPIO_MISC1_BASE + 7)
-
-#define TROUT_GPIO_SDMC_CD_N                (TROUT_GPIO_VIRTUAL_BASE + 0)
-#define TROUT_GPIO_END                      (TROUT_GPIO_SDMC_CD_N)
-#define TROUT_GPIO_BANK1_FIRST_INT_SOURCE   (TROUT_GPIO_SDMC_CD_N)
-#define TROUT_GPIO_BANK1_LAST_INT_SOURCE    (TROUT_GPIO_SDMC_CD_N)
-
-#define TROUT_GPIO_VIRTUAL_TO_REAL_OFFSET \
-	(TROUT_GPIO_INT5_BASE - TROUT_GPIO_VIRTUAL_BASE)
-
-#define TROUT_INT_START (NR_MSM_IRQS + NR_GPIO_IRQS)
-#define TROUT_INT_BANK0_COUNT (8)
-#define TROUT_INT_BANK1_START (TROUT_INT_START + TROUT_INT_BANK0_COUNT)
-#define TROUT_INT_BANK1_COUNT (1)
-#define TROUT_INT_END (TROUT_INT_START + TROUT_INT_BANK0_COUNT + \
-			TROUT_INT_BANK1_COUNT - 1)
-#define TROUT_GPIO_TO_INT(n) (((n) <= TROUT_GPIO_BANK0_LAST_INT_SOURCE) ? \
-	(TROUT_INT_START - TROUT_GPIO_BANK0_FIRST_INT_SOURCE + (n)) : \
-	(TROUT_INT_BANK1_START - TROUT_GPIO_BANK1_FIRST_INT_SOURCE + (n)))
-
-#define TROUT_INT_TO_BANK(n) ((n - TROUT_INT_START) / TROUT_INT_BANK0_COUNT)
-#define TROUT_INT_TO_MASK(n) (1U << ((n - TROUT_INT_START) & 7))
-#define TROUT_BANK_TO_MASK_REG(bank) \
-	(bank ? TROUT_GPIO_INT_MASK1_REG : TROUT_GPIO_INT_MASK0_REG)
-#define TROUT_BANK_TO_STAT_REG(bank) \
-	(bank ? TROUT_GPIO_INT_STAT1_REG : TROUT_GPIO_INT_STAT0_REG)
-
-#endif /* GUARD */
diff --git a/arch/arm/mach-msm/clock-pcom.c b/arch/arm/mach-msm/clock-pcom.c
deleted file mode 100644
index f5b69d7..0000000
--- a/arch/arm/mach-msm/clock-pcom.c
+++ /dev/null
@@ -1,176 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/err.h>
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/clk-provider.h>
-#include <linux/clkdev.h>
-
-#include <mach/clk.h>
-
-#include "proc_comm.h"
-#include "clock.h"
-#include "clock-pcom.h"
-
-struct clk_pcom {
-	unsigned id;
-	unsigned long flags;
-	struct msm_clk msm_clk;
-};
-
-static inline struct clk_pcom *to_clk_pcom(struct clk_hw *hw)
-{
-	return container_of(to_msm_clk(hw), struct clk_pcom, msm_clk);
-}
-
-static int pc_clk_enable(struct clk_hw *hw)
-{
-	unsigned id = to_clk_pcom(hw)->id;
-	int rc = msm_proc_comm(PCOM_CLKCTL_RPC_ENABLE, &id, NULL);
-	if (rc < 0)
-		return rc;
-	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
-static void pc_clk_disable(struct clk_hw *hw)
-{
-	unsigned id = to_clk_pcom(hw)->id;
-	msm_proc_comm(PCOM_CLKCTL_RPC_DISABLE, &id, NULL);
-}
-
-static int pc_clk_reset(struct clk_hw *hw, enum clk_reset_action action)
-{
-	int rc;
-	unsigned id = to_clk_pcom(hw)->id;
-
-	if (action == CLK_RESET_ASSERT)
-		rc = msm_proc_comm(PCOM_CLKCTL_RPC_RESET_ASSERT, &id, NULL);
-	else
-		rc = msm_proc_comm(PCOM_CLKCTL_RPC_RESET_DEASSERT, &id, NULL);
-
-	if (rc < 0)
-		return rc;
-	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
-static int pc_clk_set_rate(struct clk_hw *hw, unsigned long new_rate,
-			   unsigned long p_rate)
-{
-	struct clk_pcom *p = to_clk_pcom(hw);
-	unsigned id = p->id, rate = new_rate;
-	int rc;
-
-	/*
-	 * The rate _might_ be rounded off to the nearest KHz value by the
-	 * remote function. So a return value of 0 doesn't necessarily mean
-	 * that the exact rate was set successfully.
-	 */
-	if (p->flags & CLKFLAG_MIN)
-		rc = msm_proc_comm(PCOM_CLKCTL_RPC_MIN_RATE, &id, &rate);
-	else
-		rc = msm_proc_comm(PCOM_CLKCTL_RPC_SET_RATE, &id, &rate);
-	if (rc < 0)
-		return rc;
-	else
-		return (int)id < 0 ? -EINVAL : 0;
-}
-
-static unsigned long pc_clk_recalc_rate(struct clk_hw *hw, unsigned long p_rate)
-{
-	unsigned id = to_clk_pcom(hw)->id;
-	if (msm_proc_comm(PCOM_CLKCTL_RPC_RATE, &id, NULL))
-		return 0;
-	else
-		return id;
-}
-
-static int pc_clk_is_enabled(struct clk_hw *hw)
-{
-	unsigned id = to_clk_pcom(hw)->id;
-	if (msm_proc_comm(PCOM_CLKCTL_RPC_ENABLED, &id, NULL))
-		return 0;
-	else
-		return id;
-}
-
-static long pc_clk_round_rate(struct clk_hw *hw, unsigned long rate,
-			      unsigned long *p_rate)
-{
-	/* Not really supported; pc_clk_set_rate() does rounding on it's own. */
-	return rate;
-}
-
-static struct clk_ops clk_ops_pcom = {
-	.enable = pc_clk_enable,
-	.disable = pc_clk_disable,
-	.set_rate = pc_clk_set_rate,
-	.recalc_rate = pc_clk_recalc_rate,
-	.is_enabled = pc_clk_is_enabled,
-	.round_rate = pc_clk_round_rate,
-};
-
-static int msm_clock_pcom_probe(struct platform_device *pdev)
-{
-	const struct pcom_clk_pdata *pdata = pdev->dev.platform_data;
-	int i, ret;
-
-	for (i = 0; i < pdata->num_lookups; i++) {
-		const struct clk_pcom_desc *desc = &pdata->lookup[i];
-		struct clk *c;
-		struct clk_pcom *p;
-		struct clk_hw *hw;
-		struct clk_init_data init;
-
-		p = devm_kzalloc(&pdev->dev, sizeof(*p), GFP_KERNEL);
-		if (!p)
-			return -ENOMEM;
-
-		p->id = desc->id;
-		p->flags = desc->flags;
-		p->msm_clk.reset = pc_clk_reset;
-
-		hw = &p->msm_clk.hw;
-		hw->init = &init;
-
-		init.name = desc->name;
-		init.ops = &clk_ops_pcom;
-		init.num_parents = 0;
-		init.flags = CLK_IS_ROOT;
-
-		if (!(p->flags & CLKFLAG_AUTO_OFF))
-			init.flags |= CLK_IGNORE_UNUSED;
-
-		c = devm_clk_register(&pdev->dev, hw);
-		ret = clk_register_clkdev(c, desc->con, desc->dev);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
-}
-
-static struct platform_driver msm_clock_pcom_driver = {
-	.probe		= msm_clock_pcom_probe,
-	.driver		= {
-		.name	= "msm-clock-pcom",
-	},
-};
-module_platform_driver(msm_clock_pcom_driver);
-
-MODULE_LICENSE("GPL v2");
diff --git a/arch/arm/mach-msm/clock-pcom.h b/arch/arm/mach-msm/clock-pcom.h
deleted file mode 100644
index 5bb164f..0000000
--- a/arch/arm/mach-msm/clock-pcom.h
+++ /dev/null
@@ -1,145 +0,0 @@
-/*
- * Copyright (c) 2009-2012, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_CLOCK_PCOM_H
-#define __ARCH_ARM_MACH_MSM_CLOCK_PCOM_H
-
-/* clock IDs used by the modem processor */
-
-#define P_ACPU_CLK	0   /* Applications processor clock */
-#define P_ADM_CLK	1   /* Applications data mover clock */
-#define P_ADSP_CLK	2   /* ADSP clock */
-#define P_EBI1_CLK	3   /* External bus interface 1 clock */
-#define P_EBI2_CLK	4   /* External bus interface 2 clock */
-#define P_ECODEC_CLK	5   /* External CODEC clock */
-#define P_EMDH_CLK	6   /* External MDDI host clock */
-#define P_GP_CLK	7   /* General purpose clock */
-#define P_GRP_3D_CLK	8   /* Graphics clock */
-#define P_I2C_CLK	9   /* I2C clock */
-#define P_ICODEC_RX_CLK	10  /* Internal CODEX RX clock */
-#define P_ICODEC_TX_CLK	11  /* Internal CODEX TX clock */
-#define P_IMEM_CLK	12  /* Internal graphics memory clock */
-#define P_MDC_CLK	13  /* MDDI client clock */
-#define P_MDP_CLK	14  /* Mobile display processor clock */
-#define P_PBUS_CLK	15  /* Peripheral bus clock */
-#define P_PCM_CLK	16  /* PCM clock */
-#define P_PMDH_CLK	17  /* Primary MDDI host clock */
-#define P_SDAC_CLK	18  /* Stereo DAC clock */
-#define P_SDC1_CLK	19  /* Secure Digital Card clocks */
-#define P_SDC1_P_CLK	20
-#define P_SDC2_CLK	21
-#define P_SDC2_P_CLK	22
-#define P_SDC3_CLK	23
-#define P_SDC3_P_CLK	24
-#define P_SDC4_CLK	25
-#define P_SDC4_P_CLK	26
-#define P_TSIF_CLK	27  /* Transport Stream Interface clocks */
-#define P_TSIF_REF_CLK	28
-#define P_TV_DAC_CLK	29  /* TV clocks */
-#define P_TV_ENC_CLK	30
-#define P_UART1_CLK	31  /* UART clocks */
-#define P_UART2_CLK	32
-#define P_UART3_CLK	33
-#define P_UART1DM_CLK	34
-#define P_UART2DM_CLK	35
-#define P_USB_HS_CLK	36  /* High speed USB core clock */
-#define P_USB_HS_P_CLK	37  /* High speed USB pbus clock */
-#define P_USB_OTG_CLK	38  /* Full speed USB clock */
-#define P_VDC_CLK	39  /* Video controller clock */
-#define P_VFE_MDC_CLK	40  /* Camera / Video Front End clock */
-#define P_VFE_CLK	41  /* VFE MDDI client clock */
-#define P_MDP_LCDC_PCLK_CLK	42
-#define P_MDP_LCDC_PAD_PCLK_CLK 43
-#define P_MDP_VSYNC_CLK	44
-#define P_SPI_CLK	45
-#define P_VFE_AXI_CLK	46
-#define P_USB_HS2_CLK	47  /* High speed USB 2 core clock */
-#define P_USB_HS2_P_CLK	48  /* High speed USB 2 pbus clock */
-#define P_USB_HS3_CLK	49  /* High speed USB 3 core clock */
-#define P_USB_HS3_P_CLK	50  /* High speed USB 3 pbus clock */
-#define P_GRP_3D_P_CLK	51  /* Graphics pbus clock */
-#define P_USB_PHY_CLK	52  /* USB PHY clock */
-#define P_USB_HS_CORE_CLK	53  /* High speed USB 1 core clock */
-#define P_USB_HS2_CORE_CLK	54  /* High speed USB 2 core clock */
-#define P_USB_HS3_CORE_CLK	55  /* High speed USB 3 core clock */
-#define P_CAM_M_CLK		56
-#define P_CAMIF_PAD_P_CLK	57
-#define P_GRP_2D_CLK		58
-#define P_GRP_2D_P_CLK		59
-#define P_I2S_CLK		60
-#define P_JPEG_CLK		61
-#define P_JPEG_P_CLK		62
-#define P_LPA_CODEC_CLK		63
-#define P_LPA_CORE_CLK		64
-#define P_LPA_P_CLK		65
-#define P_MDC_IO_CLK		66
-#define P_MDC_P_CLK		67
-#define P_MFC_CLK		68
-#define P_MFC_DIV2_CLK		69
-#define P_MFC_P_CLK		70
-#define P_QUP_I2C_CLK		71
-#define P_ROTATOR_IMEM_CLK	72
-#define P_ROTATOR_P_CLK		73
-#define P_VFE_CAMIF_CLK		74
-#define P_VFE_P_CLK		75
-#define P_VPE_CLK		76
-#define P_I2C_2_CLK		77
-#define P_MI2S_CODEC_RX_S_CLK	78
-#define P_MI2S_CODEC_RX_M_CLK	79
-#define P_MI2S_CODEC_TX_S_CLK	80
-#define P_MI2S_CODEC_TX_M_CLK	81
-#define P_PMDH_P_CLK		82
-#define P_EMDH_P_CLK		83
-#define P_SPI_P_CLK		84
-#define P_TSIF_P_CLK		85
-#define P_MDP_P_CLK		86
-#define P_SDAC_M_CLK		87
-#define P_MI2S_S_CLK		88
-#define P_MI2S_M_CLK		89
-#define P_AXI_ROTATOR_CLK	90
-#define P_HDMI_CLK		91
-#define P_CSI0_CLK		92
-#define P_CSI0_VFE_CLK		93
-#define P_CSI0_P_CLK		94
-#define P_CSI1_CLK		95
-#define P_CSI1_VFE_CLK		96
-#define P_CSI1_P_CLK		97
-#define P_GSBI_CLK		98
-#define P_GSBI_P_CLK		99
-#define P_CE_CLK		100 /* Crypto engine */
-#define P_CODEC_SSBI_CLK	101
-
-#define P_NR_CLKS		102
-
-struct clk_pcom_desc {
-	unsigned id;
-	const char *name;
-	const char *con;
-	const char *dev;
-	unsigned long flags;
-};
-
-struct pcom_clk_pdata {
-	struct clk_pcom_desc *lookup;
-	u32 num_lookups;
-};
-
-#define CLK_PCOM(clk_name, clk_id, clk_dev, clk_flags) {	\
-	.id = P_##clk_id,					\
-	.name = #clk_id,					\
-	.con = clk_name,					\
-	.dev = clk_dev,						\
-	.flags = clk_flags,					\
-	}
-
-#endif
diff --git a/arch/arm/mach-msm/clock.c b/arch/arm/mach-msm/clock.c
deleted file mode 100644
index 35ea02b5..0000000
--- a/arch/arm/mach-msm/clock.c
+++ /dev/null
@@ -1,28 +0,0 @@
-/* arch/arm/mach-msm/clock.c
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/clk-provider.h>
-#include <linux/module.h>
-
-#include "clock.h"
-
-int clk_reset(struct clk *clk, enum clk_reset_action action)
-{
-	struct clk_hw *hw = __clk_get_hw(clk);
-	struct msm_clk *m = to_msm_clk(hw);
-	return m->reset(hw, action);
-}
-EXPORT_SYMBOL(clk_reset);
diff --git a/arch/arm/mach-msm/clock.h b/arch/arm/mach-msm/clock.h
deleted file mode 100644
index 42d29dd..0000000
--- a/arch/arm/mach-msm/clock.h
+++ /dev/null
@@ -1,43 +0,0 @@
-/* arch/arm/mach-msm/clock.h
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007-2012, The Linux Foundation. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_CLOCK_H
-#define __ARCH_ARM_MACH_MSM_CLOCK_H
-
-#include <linux/clk-provider.h>
-#include <mach/clk.h>
-
-#define CLK_FIRST_AVAILABLE_FLAG	0x00000100
-#define CLKFLAG_AUTO_OFF		0x00000200
-#define CLKFLAG_MIN			0x00000400
-#define CLKFLAG_MAX			0x00000800
-
-#define OFF CLKFLAG_AUTO_OFF
-#define CLK_MIN CLKFLAG_MIN
-#define CLK_MAX CLKFLAG_MAX
-#define CLK_MINMAX (CLK_MIN | CLK_MAX)
-
-struct msm_clk {
-	int (*reset)(struct clk_hw *hw, enum clk_reset_action action);
-	struct clk_hw hw;
-};
-
-static inline struct msm_clk *to_msm_clk(struct clk_hw *hw)
-{
-	return container_of(hw, struct msm_clk, hw);
-}
-
-#endif
diff --git a/arch/arm/mach-msm/common.h b/arch/arm/mach-msm/common.h
deleted file mode 100644
index 572479a..0000000
--- a/arch/arm/mach-msm/common.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/* Copyright (c) 2012, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-#ifndef __MACH_COMMON_H
-#define __MACH_COMMON_H
-
-extern void msm7x01_timer_init(void);
-extern void msm7x30_timer_init(void);
-extern void qsd8x50_timer_init(void);
-
-extern void msm_map_common_io(void);
-extern void msm_map_msm7x30_io(void);
-extern void msm_map_qsd8x50_io(void);
-
-extern void __iomem *__msm_ioremap_caller(phys_addr_t phys_addr, size_t size,
-					  unsigned int mtype, void *caller);
-
-struct msm_mmc_platform_data;
-
-extern void msm_add_devices(void);
-extern void msm_init_irq(void);
-extern void msm_init_gpio(void);
-extern int msm_add_sdcc(unsigned int controller,
-			struct msm_mmc_platform_data *plat,
-			unsigned int stat_irq, unsigned long stat_irq_flags);
-
-#if defined(CONFIG_MSM_SMD) && defined(CONFIG_DEBUG_FS)
-extern int smd_debugfs_init(void);
-#else
-static inline int smd_debugfs_init(void) { return 0; }
-#endif
-
-#endif
diff --git a/arch/arm/mach-msm/devices-msm7x00.c b/arch/arm/mach-msm/devices-msm7x00.c
deleted file mode 100644
index d83404d..0000000
--- a/arch/arm/mach-msm/devices-msm7x00.c
+++ /dev/null
@@ -1,480 +0,0 @@
-/* linux/arch/arm/mach-msm/devices.c
- *
- * Copyright (C) 2008 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/clkdev.h>
-
-#include <mach/irqs.h>
-#include <mach/msm_iomap.h>
-#include "devices.h"
-
-#include <asm/mach/flash.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-
-#include "clock.h"
-#include "clock-pcom.h"
-#include <linux/platform_data/mmc-msm_sdcc.h>
-
-static struct resource msm_gpio_resources[] = {
-	{
-		.start	= 32 + 0,
-		.end	= 32 + 0,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 32 + 1,
-		.end	= 32 + 1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 0xa9200800,
-		.end	= 0xa9200800 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio1"
-	},
-	{
-		.start	= 0xa9300C00,
-		.end	= 0xa9300C00 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio2"
-	},
-};
-
-struct platform_device msm_device_gpio_7201 = {
-	.name	= "gpio-msm-7201",
-	.num_resources	= ARRAY_SIZE(msm_gpio_resources),
-	.resource	= msm_gpio_resources,
-};
-
-static struct resource resources_uart1[] = {
-	{
-		.start	= INT_UART1,
-		.end	= INT_UART1,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= MSM_UART1_PHYS,
-		.end	= MSM_UART1_PHYS + MSM_UART1_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "uart_resource"
-	},
-};
-
-static struct resource resources_uart2[] = {
-	{
-		.start	= INT_UART2,
-		.end	= INT_UART2,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= MSM_UART2_PHYS,
-		.end	= MSM_UART2_PHYS + MSM_UART2_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "uart_resource"
-	},
-};
-
-static struct resource resources_uart3[] = {
-	{
-		.start	= INT_UART3,
-		.end	= INT_UART3,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= MSM_UART3_PHYS,
-		.end	= MSM_UART3_PHYS + MSM_UART3_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "uart_resource"
-	},
-};
-
-struct platform_device msm_device_uart1 = {
-	.name	= "msm_serial",
-	.id	= 0,
-	.num_resources	= ARRAY_SIZE(resources_uart1),
-	.resource	= resources_uart1,
-};
-
-struct platform_device msm_device_uart2 = {
-	.name	= "msm_serial",
-	.id	= 1,
-	.num_resources	= ARRAY_SIZE(resources_uart2),
-	.resource	= resources_uart2,
-};
-
-struct platform_device msm_device_uart3 = {
-	.name	= "msm_serial",
-	.id	= 2,
-	.num_resources	= ARRAY_SIZE(resources_uart3),
-	.resource	= resources_uart3,
-};
-
-static struct resource resources_i2c[] = {
-	{
-		.start	= MSM_I2C_PHYS,
-		.end	= MSM_I2C_PHYS + MSM_I2C_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_PWB_I2C,
-		.end	= INT_PWB_I2C,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_i2c = {
-	.name		= "msm_i2c",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(resources_i2c),
-	.resource	= resources_i2c,
-};
-
-static struct resource resources_hsusb[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_hsusb = {
-	.name		= "msm_hsusb",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_hsusb),
-	.resource	= resources_hsusb,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct flash_platform_data msm_nand_data = {
-	.parts		= NULL,
-	.nr_parts	= 0,
-};
-
-static struct resource resources_nand[] = {
-	[0] = {
-		.start	= 7,
-		.end	= 7,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-struct platform_device msm_device_nand = {
-	.name		= "msm_nand",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_nand),
-	.resource	= resources_nand,
-	.dev		= {
-		.platform_data	= &msm_nand_data,
-	},
-};
-
-struct platform_device msm_device_smd = {
-	.name	= "msm_smd",
-	.id	= -1,
-};
-
-static struct resource resources_sdc1[] = {
-	{
-		.start	= MSM_SDC1_PHYS,
-		.end	= MSM_SDC1_PHYS + MSM_SDC1_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC1_0,
-		.end	= INT_SDC1_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc2[] = {
-	{
-		.start	= MSM_SDC2_PHYS,
-		.end	= MSM_SDC2_PHYS + MSM_SDC2_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC2_0,
-		.end	= INT_SDC2_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc3[] = {
-	{
-		.start	= MSM_SDC3_PHYS,
-		.end	= MSM_SDC3_PHYS + MSM_SDC3_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC3_0,
-		.end	= INT_SDC3_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc4[] = {
-	{
-		.start	= MSM_SDC4_PHYS,
-		.end	= MSM_SDC4_PHYS + MSM_SDC4_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC4_0,
-		.end	= INT_SDC4_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-struct platform_device msm_device_sdc1 = {
-	.name		= "msm_sdcc",
-	.id		= 1,
-	.num_resources	= ARRAY_SIZE(resources_sdc1),
-	.resource	= resources_sdc1,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc2 = {
-	.name		= "msm_sdcc",
-	.id		= 2,
-	.num_resources	= ARRAY_SIZE(resources_sdc2),
-	.resource	= resources_sdc2,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc3 = {
-	.name		= "msm_sdcc",
-	.id		= 3,
-	.num_resources	= ARRAY_SIZE(resources_sdc3),
-	.resource	= resources_sdc3,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc4 = {
-	.name		= "msm_sdcc",
-	.id		= 4,
-	.num_resources	= ARRAY_SIZE(resources_sdc4),
-	.resource	= resources_sdc4,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static struct platform_device *msm_sdcc_devices[] __initdata = {
-	&msm_device_sdc1,
-	&msm_device_sdc2,
-	&msm_device_sdc3,
-	&msm_device_sdc4,
-};
-
-int __init msm_add_sdcc(unsigned int controller,
-			struct msm_mmc_platform_data *plat,
-			unsigned int stat_irq, unsigned long stat_irq_flags)
-{
-	struct platform_device	*pdev;
-	struct resource *res;
-
-	if (controller < 1 || controller > 4)
-		return -EINVAL;
-
-	pdev = msm_sdcc_devices[controller-1];
-	pdev->dev.platform_data = plat;
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "status_irq");
-	if (!res)
-		return -EINVAL;
-	else if (stat_irq) {
-		res->start = res->end = stat_irq;
-		res->flags &= ~IORESOURCE_DISABLED;
-		res->flags |= stat_irq_flags;
-	}
-
-	return platform_device_register(pdev);
-}
-
-static struct resource resources_mddi0[] = {
-	{
-		.start	= MSM_PMDH_PHYS,
-		.end	= MSM_PMDH_PHYS + MSM_PMDH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_MDDI_PRI,
-		.end	= INT_MDDI_PRI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct resource resources_mddi1[] = {
-	{
-		.start	= MSM_EMDH_PHYS,
-		.end	= MSM_EMDH_PHYS + MSM_EMDH_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_MDDI_EXT,
-		.end	= INT_MDDI_EXT,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_mddi0 = {
-	.name = "msm_mddi",
-	.id = 0,
-	.num_resources = ARRAY_SIZE(resources_mddi0),
-	.resource = resources_mddi0,
-	.dev = {
-		.coherent_dma_mask      = 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_mddi1 = {
-	.name = "msm_mddi",
-	.id = 1,
-	.num_resources = ARRAY_SIZE(resources_mddi1),
-	.resource = resources_mddi1,
-	.dev = {
-		.coherent_dma_mask      = 0xffffffff,
-	},
-};
-
-static struct resource resources_mdp[] = {
-	{
-		.start	= MSM_MDP_PHYS,
-		.end	= MSM_MDP_PHYS + MSM_MDP_SIZE - 1,
-		.name	= "mdp",
-		.flags	= IORESOURCE_MEM
-	},
-	{
-		.start	= INT_MDP,
-		.end	= INT_MDP,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_mdp = {
-	.name = "msm_mdp",
-	.id = 0,
-	.num_resources = ARRAY_SIZE(resources_mdp),
-	.resource = resources_mdp,
-};
-
-static struct clk_pcom_desc msm_clocks_7x01a[] = {
-	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
-	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
-	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, 0),
-	CLK_PCOM("ebi2_clk",	EBI2_CLK,	NULL, 0),
-	CLK_PCOM("ecodec_clk",	ECODEC_CLK,	NULL, 0),
-	CLK_PCOM("emdh_clk",	EMDH_CLK,	NULL, OFF),
-	CLK_PCOM("gp_clk",		GP_CLK,		NULL, 0),
-	CLK_PCOM("grp_clk",	GRP_3D_CLK,	NULL, OFF),
-	CLK_PCOM("i2c_clk",	I2C_CLK,	"msm_i2c.0", 0),
-	CLK_PCOM("icodec_rx_clk",	ICODEC_RX_CLK,	NULL, 0),
-	CLK_PCOM("icodec_tx_clk",	ICODEC_TX_CLK,	NULL, 0),
-	CLK_PCOM("imem_clk",	IMEM_CLK,	NULL, OFF),
-	CLK_PCOM("mdc_clk",	MDC_CLK,	NULL, 0),
-	CLK_PCOM("mdp_clk",	MDP_CLK,	NULL, OFF),
-	CLK_PCOM("pbus_clk",	PBUS_CLK,	NULL, 0),
-	CLK_PCOM("pcm_clk",	PCM_CLK,	NULL, 0),
-	CLK_PCOM("mddi_clk",	PMDH_CLK,	NULL, OFF | CLK_MINMAX),
-	CLK_PCOM("sdac_clk",	SDAC_CLK,	NULL, OFF),
-	CLK_PCOM("sdc_clk",	SDC1_CLK,	"msm_sdcc.1", OFF),
-	CLK_PCOM("sdc_pclk",	SDC1_P_CLK,	"msm_sdcc.1", OFF),
-	CLK_PCOM("sdc_clk",	SDC2_CLK,	"msm_sdcc.2", OFF),
-	CLK_PCOM("sdc_pclk",	SDC2_P_CLK,	"msm_sdcc.2", OFF),
-	CLK_PCOM("sdc_clk",	SDC3_CLK,	"msm_sdcc.3", OFF),
-	CLK_PCOM("sdc_pclk",	SDC3_P_CLK,	"msm_sdcc.3", OFF),
-	CLK_PCOM("sdc_clk",	SDC4_CLK,	"msm_sdcc.4", OFF),
-	CLK_PCOM("sdc_pclk",	SDC4_P_CLK,	"msm_sdcc.4", OFF),
-	CLK_PCOM("tsif_clk",	TSIF_CLK,	NULL, 0),
-	CLK_PCOM("tsif_ref_clk",	TSIF_REF_CLK,	NULL, 0),
-	CLK_PCOM("tv_dac_clk",	TV_DAC_CLK,	NULL, 0),
-	CLK_PCOM("tv_enc_clk",	TV_ENC_CLK,	NULL, 0),
-	CLK_PCOM("core",	UART1_CLK,	"msm_serial.0", OFF),
-	CLK_PCOM("core",	UART2_CLK,	"msm_serial.1", 0),
-	CLK_PCOM("core",	UART3_CLK,	"msm_serial.2", OFF),
-	CLK_PCOM("uart1dm_clk",	UART1DM_CLK,	NULL, OFF),
-	CLK_PCOM("uart2dm_clk",	UART2DM_CLK,	NULL, 0),
-	CLK_PCOM("usb_hs_clk",	USB_HS_CLK,	"msm_hsusb", OFF),
-	CLK_PCOM("usb_hs_pclk",	USB_HS_P_CLK,	"msm_hsusb", OFF),
-	CLK_PCOM("usb_otg_clk",	USB_OTG_CLK,	NULL, 0),
-	CLK_PCOM("vdc_clk",	VDC_CLK,	NULL, OFF ),
-	CLK_PCOM("vfe_clk",	VFE_CLK,	NULL, OFF),
-	CLK_PCOM("vfe_mdc_clk",	VFE_MDC_CLK,	NULL, OFF),
-};
-
-static struct pcom_clk_pdata msm_clock_7x01a_pdata = {
-	.lookup = msm_clocks_7x01a,
-	.num_lookups = ARRAY_SIZE(msm_clocks_7x01a),
-};
-
-struct platform_device msm_clock_7x01a = {
-	.name = "msm-clock-pcom",
-	.dev.platform_data = &msm_clock_7x01a_pdata,
-};
diff --git a/arch/arm/mach-msm/devices-msm7x30.c b/arch/arm/mach-msm/devices-msm7x30.c
deleted file mode 100644
index c15ea8a..0000000
--- a/arch/arm/mach-msm/devices-msm7x30.c
+++ /dev/null
@@ -1,246 +0,0 @@
-/*
- * Copyright (C) 2008 Google, Inc.
- * Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/clkdev.h>
-#include <mach/irqs.h>
-#include <mach/msm_iomap.h>
-#include <mach/dma.h>
-
-#include "devices.h"
-#include "smd_private.h"
-#include "common.h"
-
-#include <asm/mach/flash.h>
-
-#include "clock.h"
-#include "clock-pcom.h"
-
-#include <linux/platform_data/mmc-msm_sdcc.h>
-
-static struct resource msm_gpio_resources[] = {
-	{
-		.start	= 32 + 18,
-		.end	= 32 + 18,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 32 + 19,
-		.end	= 32 + 19,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 0xac001000,
-		.end	= 0xac001000 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio1"
-	},
-	{
-		.start	= 0xac101400,
-		.end	= 0xac101400 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio2"
-	},
-};
-
-struct platform_device msm_device_gpio_7x30 = {
-	.name	= "gpio-msm-7x30",
-	.num_resources	= ARRAY_SIZE(msm_gpio_resources),
-	.resource	= msm_gpio_resources,
-};
-
-static struct resource resources_uart2[] = {
-	{
-		.start	= INT_UART2,
-		.end	= INT_UART2,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= MSM_UART2_PHYS,
-		.end	= MSM_UART2_PHYS + MSM_UART2_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "uart_resource"
-	},
-};
-
-struct platform_device msm_device_uart2 = {
-	.name	= "msm_serial",
-	.id	= 1,
-	.num_resources	= ARRAY_SIZE(resources_uart2),
-	.resource	= resources_uart2,
-};
-
-struct platform_device msm_device_smd = {
-	.name   = "msm_smd",
-	.id     = -1,
-};
-
-static struct resource resources_otg[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_otg = {
-	.name		= "msm_otg",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_otg),
-	.resource	= resources_otg,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static struct resource resources_hsusb[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_hsusb = {
-	.name		= "msm_hsusb",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_hsusb),
-	.resource	= resources_hsusb,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static u64 dma_mask = 0xffffffffULL;
-static struct resource resources_hsusb_host[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_hsusb_host = {
-	.name		= "msm_hsusb_host",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_hsusb_host),
-	.resource	= resources_hsusb_host,
-	.dev		= {
-		.dma_mask               = &dma_mask,
-		.coherent_dma_mask      = 0xffffffffULL,
-	},
-};
-
-static struct clk_pcom_desc msm_clocks_7x30[] = {
-	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
-	CLK_PCOM("adsp_clk",	ADSP_CLK,	NULL, 0),
-	CLK_PCOM("cam_m_clk",	CAM_M_CLK,	NULL, 0),
-	CLK_PCOM("camif_pad_pclk",	CAMIF_PAD_P_CLK,	NULL, OFF),
-	CLK_PCOM("ce_clk",	CE_CLK,	NULL, 0),
-	CLK_PCOM("codec_ssbi_clk",	CODEC_SSBI_CLK,	NULL, 0),
-	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, CLK_MIN),
-	CLK_PCOM("ecodec_clk",	ECODEC_CLK,	NULL, 0),
-	CLK_PCOM("emdh_clk",	EMDH_CLK,	NULL, OFF | CLK_MINMAX),
-	CLK_PCOM("emdh_pclk",	EMDH_P_CLK,	NULL, OFF),
-	CLK_PCOM("gp_clk",	GP_CLK,		NULL, 0),
-	CLK_PCOM("grp_2d_clk",	GRP_2D_CLK,	NULL, 0),
-	CLK_PCOM("grp_2d_pclk",	GRP_2D_P_CLK,	NULL, 0),
-	CLK_PCOM("grp_clk",	GRP_3D_CLK,	NULL, 0),
-	CLK_PCOM("grp_pclk",	GRP_3D_P_CLK,	NULL, 0),
-	CLK_PCOM("hdmi_clk",	HDMI_CLK,	NULL, 0),
-	CLK_PCOM("imem_clk",	IMEM_CLK,	NULL, OFF),
-	CLK_PCOM("jpeg_clk",	JPEG_CLK,	NULL, OFF),
-	CLK_PCOM("jpeg_pclk",	JPEG_P_CLK,	NULL, OFF),
-	CLK_PCOM("lpa_codec_clk",	LPA_CODEC_CLK,		NULL, 0),
-	CLK_PCOM("lpa_core_clk",	LPA_CORE_CLK,		NULL, 0),
-	CLK_PCOM("lpa_pclk",		LPA_P_CLK,		NULL, 0),
-	CLK_PCOM("mdc_clk",	MDC_CLK,	NULL, 0),
-	CLK_PCOM("mddi_clk",	PMDH_CLK,	NULL, OFF | CLK_MINMAX),
-	CLK_PCOM("mddi_pclk",	PMDH_P_CLK,	NULL, 0),
-	CLK_PCOM("mdp_clk",	MDP_CLK,	NULL, OFF),
-	CLK_PCOM("mdp_pclk",	MDP_P_CLK,	NULL, 0),
-	CLK_PCOM("mdp_lcdc_pclk_clk", MDP_LCDC_PCLK_CLK, NULL, 0),
-	CLK_PCOM("mdp_lcdc_pad_pclk_clk", MDP_LCDC_PAD_PCLK_CLK, NULL, 0),
-	CLK_PCOM("mdp_vsync_clk",	MDP_VSYNC_CLK,  NULL, 0),
-	CLK_PCOM("mfc_clk",		MFC_CLK,		NULL, 0),
-	CLK_PCOM("mfc_div2_clk",	MFC_DIV2_CLK,		NULL, 0),
-	CLK_PCOM("mfc_pclk",		MFC_P_CLK,		NULL, 0),
-	CLK_PCOM("mi2s_m_clk",		MI2S_M_CLK,  		NULL, 0),
-	CLK_PCOM("mi2s_s_clk",		MI2S_S_CLK,  		NULL, 0),
-	CLK_PCOM("mi2s_codec_rx_m_clk",	MI2S_CODEC_RX_M_CLK,  NULL, 0),
-	CLK_PCOM("mi2s_codec_rx_s_clk",	MI2S_CODEC_RX_S_CLK,  NULL, 0),
-	CLK_PCOM("mi2s_codec_tx_m_clk",	MI2S_CODEC_TX_M_CLK,  NULL, 0),
-	CLK_PCOM("mi2s_codec_tx_s_clk",	MI2S_CODEC_TX_S_CLK,  NULL, 0),
-	CLK_PCOM("pbus_clk",	PBUS_CLK,	NULL, CLK_MIN),
-	CLK_PCOM("pcm_clk",	PCM_CLK,	NULL, 0),
-	CLK_PCOM("rotator_clk",	AXI_ROTATOR_CLK,		NULL, 0),
-	CLK_PCOM("rotator_imem_clk",	ROTATOR_IMEM_CLK,	NULL, OFF),
-	CLK_PCOM("rotator_pclk",	ROTATOR_P_CLK,		NULL, OFF),
-	CLK_PCOM("sdac_clk",	SDAC_CLK,	NULL, OFF),
-	CLK_PCOM("spi_clk",	SPI_CLK,	NULL, 0),
-	CLK_PCOM("spi_pclk",	SPI_P_CLK,	NULL, 0),
-	CLK_PCOM("tv_dac_clk",	TV_DAC_CLK,	NULL, 0),
-	CLK_PCOM("tv_enc_clk",	TV_ENC_CLK,	NULL, 0),
-	CLK_PCOM("core",	UART2_CLK,	"msm_serial.1", 0),
-	CLK_PCOM("usb_phy_clk",	USB_PHY_CLK,	NULL, 0),
-	CLK_PCOM("usb_hs_clk",		USB_HS_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs_pclk",		USB_HS_P_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs_core_clk",	USB_HS_CORE_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs2_clk",		USB_HS2_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs2_pclk",	USB_HS2_P_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs2_core_clk",	USB_HS2_CORE_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs3_clk",		USB_HS3_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs3_pclk",	USB_HS3_P_CLK,		NULL, OFF),
-	CLK_PCOM("usb_hs3_core_clk",	USB_HS3_CORE_CLK,	NULL, OFF),
-	CLK_PCOM("vdc_clk",	VDC_CLK,	NULL, OFF | CLK_MIN),
-	CLK_PCOM("vfe_camif_clk",	VFE_CAMIF_CLK, 	NULL, 0),
-	CLK_PCOM("vfe_clk",	VFE_CLK,	NULL, 0),
-	CLK_PCOM("vfe_mdc_clk",	VFE_MDC_CLK,	NULL, 0),
-	CLK_PCOM("vfe_pclk",	VFE_P_CLK,	NULL, OFF),
-	CLK_PCOM("vpe_clk",	VPE_CLK,	NULL, 0),
-
-	/* 7x30 v2 hardware only. */
-	CLK_PCOM("csi_clk",	CSI0_CLK,	NULL, 0),
-	CLK_PCOM("csi_pclk",	CSI0_P_CLK,	NULL, 0),
-	CLK_PCOM("csi_vfe_clk",	CSI0_VFE_CLK,	NULL, 0),
-};
-
-static struct pcom_clk_pdata msm_clock_7x30_pdata = {
-	.lookup = msm_clocks_7x30,
-	.num_lookups = ARRAY_SIZE(msm_clocks_7x30),
-};
-
-struct platform_device msm_clock_7x30 = {
-	.name = "msm-clock-pcom",
-	.dev.platform_data = &msm_clock_7x30_pdata,
-};
diff --git a/arch/arm/mach-msm/devices-qsd8x50.c b/arch/arm/mach-msm/devices-qsd8x50.c
deleted file mode 100644
index 9e1e9ce..0000000
--- a/arch/arm/mach-msm/devices-qsd8x50.c
+++ /dev/null
@@ -1,388 +0,0 @@
-/*
- * Copyright (C) 2008 Google, Inc.
- * Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/clkdev.h>
-#include <linux/dma-mapping.h>
-
-#include <mach/irqs.h>
-#include <mach/msm_iomap.h>
-#include <mach/dma.h>
-
-#include "devices.h"
-#include "common.h"
-
-#include <asm/mach/flash.h>
-
-#include <linux/platform_data/mmc-msm_sdcc.h>
-#include "clock.h"
-#include "clock-pcom.h"
-
-static struct resource msm_gpio_resources[] = {
-	{
-		.start	= 64 + 165 + 9,
-		.end	= 64 + 165 + 9,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 64 + 165 + 10,
-		.end	= 64 + 165 + 10,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= 0xa9000800,
-		.end	= 0xa9000800 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio1"
-	},
-	{
-		.start	= 0xa9100C00,
-		.end	= 0xa9100C00 + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "gpio2"
-	},
-};
-
-struct platform_device msm_device_gpio_8x50 = {
-	.name	= "gpio-msm-8x50",
-	.num_resources	= ARRAY_SIZE(msm_gpio_resources),
-	.resource	= msm_gpio_resources,
-};
-
-static struct resource resources_uart3[] = {
-	{
-		.start	= INT_UART3,
-		.end	= INT_UART3,
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= MSM_UART3_PHYS,
-		.end	= MSM_UART3_PHYS + MSM_UART3_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-		.name  = "uart_resource"
-	},
-};
-
-struct platform_device msm_device_uart3 = {
-	.name	= "msm_serial",
-	.id	= 2,
-	.num_resources	= ARRAY_SIZE(resources_uart3),
-	.resource	= resources_uart3,
-};
-
-struct platform_device msm_device_smd = {
-	.name   = "msm_smd",
-	.id     = -1,
-};
-
-static struct resource resources_otg[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_otg = {
-	.name		= "msm_otg",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_otg),
-	.resource	= resources_otg,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static struct resource resources_hsusb[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_hsusb = {
-	.name		= "msm_hsusb",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_hsusb),
-	.resource	= resources_hsusb,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static u64 dma_mask = 0xffffffffULL;
-static struct resource resources_hsusb_host[] = {
-	{
-		.start	= MSM_HSUSB_PHYS,
-		.end	= MSM_HSUSB_PHYS + MSM_HSUSB_SIZE,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_USB_HS,
-		.end	= INT_USB_HS,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-struct platform_device msm_device_hsusb_host = {
-	.name		= "msm_hsusb_host",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(resources_hsusb_host),
-	.resource	= resources_hsusb_host,
-	.dev		= {
-		.dma_mask               = &dma_mask,
-		.coherent_dma_mask      = 0xffffffffULL,
-	},
-};
-
-static struct resource resources_sdc1[] = {
-	{
-		.start	= MSM_SDC1_PHYS,
-		.end	= MSM_SDC1_PHYS + MSM_SDC1_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC1_0,
-		.end	= INT_SDC1_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc2[] = {
-	{
-		.start	= MSM_SDC2_PHYS,
-		.end	= MSM_SDC2_PHYS + MSM_SDC2_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC2_0,
-		.end	= INT_SDC2_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc3[] = {
-	{
-		.start	= MSM_SDC3_PHYS,
-		.end	= MSM_SDC3_PHYS + MSM_SDC3_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC3_0,
-		.end	= INT_SDC3_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct resource resources_sdc4[] = {
-	{
-		.start	= MSM_SDC4_PHYS,
-		.end	= MSM_SDC4_PHYS + MSM_SDC4_SIZE - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= INT_SDC4_0,
-		.end	= INT_SDC4_0,
-		.flags	= IORESOURCE_IRQ,
-		.name	= "cmd_irq",
-	},
-	{
-		.flags	= IORESOURCE_IRQ | IORESOURCE_DISABLED,
-		.name	= "status_irq"
-	},
-	{
-		.start	= 8,
-		.end	= 8,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-struct platform_device msm_device_sdc1 = {
-	.name		= "msm_sdcc",
-	.id		= 1,
-	.num_resources	= ARRAY_SIZE(resources_sdc1),
-	.resource	= resources_sdc1,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc2 = {
-	.name		= "msm_sdcc",
-	.id		= 2,
-	.num_resources	= ARRAY_SIZE(resources_sdc2),
-	.resource	= resources_sdc2,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc3 = {
-	.name		= "msm_sdcc",
-	.id		= 3,
-	.num_resources	= ARRAY_SIZE(resources_sdc3),
-	.resource	= resources_sdc3,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-struct platform_device msm_device_sdc4 = {
-	.name		= "msm_sdcc",
-	.id		= 4,
-	.num_resources	= ARRAY_SIZE(resources_sdc4),
-	.resource	= resources_sdc4,
-	.dev		= {
-		.coherent_dma_mask	= 0xffffffff,
-	},
-};
-
-static struct platform_device *msm_sdcc_devices[] __initdata = {
-	&msm_device_sdc1,
-	&msm_device_sdc2,
-	&msm_device_sdc3,
-	&msm_device_sdc4,
-};
-
-int __init msm_add_sdcc(unsigned int controller,
-			struct msm_mmc_platform_data *plat,
-			unsigned int stat_irq, unsigned long stat_irq_flags)
-{
-	struct platform_device	*pdev;
-	struct resource *res;
-
-	if (controller < 1 || controller > 4)
-		return -EINVAL;
-
-	pdev = msm_sdcc_devices[controller-1];
-	pdev->dev.platform_data = plat;
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "status_irq");
-	if (!res)
-		return -EINVAL;
-	else if (stat_irq) {
-		res->start = res->end = stat_irq;
-		res->flags &= ~IORESOURCE_DISABLED;
-		res->flags |= stat_irq_flags;
-	}
-
-	return platform_device_register(pdev);
-}
-
-static struct clk_pcom_desc msm_clocks_8x50[] = {
-	CLK_PCOM("adm_clk",	ADM_CLK,	NULL, 0),
-	CLK_PCOM("ce_clk",	CE_CLK,		NULL, 0),
-	CLK_PCOM("ebi1_clk",	EBI1_CLK,	NULL, CLK_MIN),
-	CLK_PCOM("ebi2_clk",	EBI2_CLK,	NULL, 0),
-	CLK_PCOM("ecodec_clk",	ECODEC_CLK,	NULL, 0),
-	CLK_PCOM("emdh_clk",	EMDH_CLK,	NULL, OFF | CLK_MINMAX),
-	CLK_PCOM("gp_clk",	GP_CLK,		NULL, 0),
-	CLK_PCOM("grp_clk",	GRP_3D_CLK,	NULL, 0),
-	CLK_PCOM("i2c_clk",	I2C_CLK,	NULL, 0),
-	CLK_PCOM("icodec_rx_clk",	ICODEC_RX_CLK,	NULL, 0),
-	CLK_PCOM("icodec_tx_clk",	ICODEC_TX_CLK,	NULL, 0),
-	CLK_PCOM("imem_clk",	IMEM_CLK,	NULL, OFF),
-	CLK_PCOM("mdc_clk",	MDC_CLK,	NULL, 0),
-	CLK_PCOM("mddi_clk",	PMDH_CLK,	NULL, OFF | CLK_MINMAX),
-	CLK_PCOM("mdp_clk",	MDP_CLK,	NULL, OFF),
-	CLK_PCOM("mdp_lcdc_pclk_clk", MDP_LCDC_PCLK_CLK, NULL, 0),
-	CLK_PCOM("mdp_lcdc_pad_pclk_clk", MDP_LCDC_PAD_PCLK_CLK, NULL, 0),
-	CLK_PCOM("mdp_vsync_clk",	MDP_VSYNC_CLK,	NULL, 0),
-	CLK_PCOM("pbus_clk",	PBUS_CLK,	NULL, CLK_MIN),
-	CLK_PCOM("pcm_clk",	PCM_CLK,	NULL, 0),
-	CLK_PCOM("sdac_clk",	SDAC_CLK,	NULL, OFF),
-	CLK_PCOM("sdc_clk",	SDC1_CLK,	"msm_sdcc.1", OFF),
-	CLK_PCOM("sdc_pclk",	SDC1_P_CLK,	"msm_sdcc.1", OFF),
-	CLK_PCOM("sdc_clk",	SDC2_CLK,	"msm_sdcc.2", OFF),
-	CLK_PCOM("sdc_pclk",	SDC2_P_CLK,	"msm_sdcc.2", OFF),
-	CLK_PCOM("sdc_clk",	SDC3_CLK,	"msm_sdcc.3", OFF),
-	CLK_PCOM("sdc_pclk",	SDC3_P_CLK,	"msm_sdcc.3", OFF),
-	CLK_PCOM("sdc_clk",	SDC4_CLK,	"msm_sdcc.4", OFF),
-	CLK_PCOM("sdc_pclk",	SDC4_P_CLK,	"msm_sdcc.4", OFF),
-	CLK_PCOM("spi_clk",	SPI_CLK,	NULL, 0),
-	CLK_PCOM("tsif_clk",	TSIF_CLK,	NULL, 0),
-	CLK_PCOM("tsif_ref_clk",	TSIF_REF_CLK,	NULL, 0),
-	CLK_PCOM("tv_dac_clk",	TV_DAC_CLK,	NULL, 0),
-	CLK_PCOM("tv_enc_clk",	TV_ENC_CLK,	NULL, 0),
-	CLK_PCOM("core",	UART1_CLK,	NULL, OFF),
-	CLK_PCOM("core",	UART2_CLK,	NULL, 0),
-	CLK_PCOM("core",	UART3_CLK,	"msm_serial.2", OFF),
-	CLK_PCOM("uartdm_clk",	UART1DM_CLK,	NULL, OFF),
-	CLK_PCOM("uartdm_clk",	UART2DM_CLK,	NULL, 0),
-	CLK_PCOM("usb_hs_clk",	USB_HS_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs_pclk",	USB_HS_P_CLK,	NULL, OFF),
-	CLK_PCOM("usb_otg_clk",	USB_OTG_CLK,	NULL, 0),
-	CLK_PCOM("vdc_clk",	VDC_CLK,	NULL, OFF | CLK_MIN),
-	CLK_PCOM("vfe_clk",	VFE_CLK,	NULL, OFF),
-	CLK_PCOM("vfe_mdc_clk",	VFE_MDC_CLK,	NULL, OFF),
-	CLK_PCOM("vfe_axi_clk",	VFE_AXI_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs2_clk",	USB_HS2_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs2_pclk",	USB_HS2_P_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs3_clk",	USB_HS3_CLK,	NULL, OFF),
-	CLK_PCOM("usb_hs3_pclk",	USB_HS3_P_CLK,	NULL, OFF),
-	CLK_PCOM("usb_phy_clk",	USB_PHY_CLK,	NULL, 0),
-};
-
-static struct pcom_clk_pdata msm_clock_8x50_pdata = {
-	.lookup = msm_clocks_8x50,
-	.num_lookups = ARRAY_SIZE(msm_clocks_8x50),
-};
-
-struct platform_device msm_clock_8x50 = {
-	.name = "msm-clock-pcom",
-	.dev.platform_data = &msm_clock_8x50_pdata,
-};
diff --git a/arch/arm/mach-msm/devices.h b/arch/arm/mach-msm/devices.h
deleted file mode 100644
index dccefad..0000000
--- a/arch/arm/mach-msm/devices.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/* linux/arch/arm/mach-msm/devices.h
- *
- * Copyright (C) 2008 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_DEVICES_H
-#define __ARCH_ARM_MACH_MSM_DEVICES_H
-
-extern struct platform_device msm_device_gpio_7201;
-extern struct platform_device msm_device_gpio_7x30;
-extern struct platform_device msm_device_gpio_8x50;
-
-extern struct platform_device msm_device_uart1;
-extern struct platform_device msm_device_uart2;
-extern struct platform_device msm_device_uart3;
-
-extern struct platform_device msm8960_device_uart_gsbi2;
-extern struct platform_device msm8960_device_uart_gsbi5;
-
-extern struct platform_device msm_device_sdc1;
-extern struct platform_device msm_device_sdc2;
-extern struct platform_device msm_device_sdc3;
-extern struct platform_device msm_device_sdc4;
-
-extern struct platform_device msm_device_hsusb;
-extern struct platform_device msm_device_otg;
-extern struct platform_device msm_device_hsusb_host;
-
-extern struct platform_device msm_device_i2c;
-
-extern struct platform_device msm_device_smd;
-
-extern struct platform_device msm_device_nand;
-
-extern struct platform_device msm_device_mddi0;
-extern struct platform_device msm_device_mddi1;
-extern struct platform_device msm_device_mdp;
-
-extern struct platform_device msm_clock_7x01a;
-extern struct platform_device msm_clock_7x30;
-extern struct platform_device msm_clock_8x50;
-
-#endif
diff --git a/arch/arm/mach-msm/dma.c b/arch/arm/mach-msm/dma.c
deleted file mode 100644
index fb976246..0000000
--- a/arch/arm/mach-msm/dma.c
+++ /dev/null
@@ -1,298 +0,0 @@
-/* linux/arch/arm/mach-msm/dma.c
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/interrupt.h>
-#include <linux/completion.h>
-#include <linux/module.h>
-#include <mach/dma.h>
-#include <mach/msm_iomap.h>
-
-#define MSM_DMOV_CHANNEL_COUNT 16
-
-#define DMOV_SD0(off, ch) (MSM_DMOV_BASE + 0x0000 + (off) + ((ch) << 2))
-#define DMOV_SD1(off, ch) (MSM_DMOV_BASE + 0x0400 + (off) + ((ch) << 2))
-#define DMOV_SD2(off, ch) (MSM_DMOV_BASE + 0x0800 + (off) + ((ch) << 2))
-#define DMOV_SD3(off, ch) (MSM_DMOV_BASE + 0x0C00 + (off) + ((ch) << 2))
-
-#if defined(CONFIG_ARCH_MSM7X30)
-#define DMOV_SD_AARM DMOV_SD2
-#else
-#define DMOV_SD_AARM DMOV_SD3
-#endif
-
-#define DMOV_CMD_PTR(ch)      DMOV_SD_AARM(0x000, ch)
-#define DMOV_RSLT(ch)         DMOV_SD_AARM(0x040, ch)
-#define DMOV_FLUSH0(ch)       DMOV_SD_AARM(0x080, ch)
-#define DMOV_FLUSH1(ch)       DMOV_SD_AARM(0x0C0, ch)
-#define DMOV_FLUSH2(ch)       DMOV_SD_AARM(0x100, ch)
-#define DMOV_FLUSH3(ch)       DMOV_SD_AARM(0x140, ch)
-#define DMOV_FLUSH4(ch)       DMOV_SD_AARM(0x180, ch)
-#define DMOV_FLUSH5(ch)       DMOV_SD_AARM(0x1C0, ch)
-
-#define DMOV_STATUS(ch)       DMOV_SD_AARM(0x200, ch)
-#define DMOV_ISR              DMOV_SD_AARM(0x380, 0)
-
-#define DMOV_CONFIG(ch)       DMOV_SD_AARM(0x300, ch)
-
-enum {
-	MSM_DMOV_PRINT_ERRORS = 1,
-	MSM_DMOV_PRINT_IO = 2,
-	MSM_DMOV_PRINT_FLOW = 4
-};
-
-static DEFINE_SPINLOCK(msm_dmov_lock);
-static struct clk *msm_dmov_clk;
-static unsigned int channel_active;
-static struct list_head ready_commands[MSM_DMOV_CHANNEL_COUNT];
-static struct list_head active_commands[MSM_DMOV_CHANNEL_COUNT];
-unsigned int msm_dmov_print_mask = MSM_DMOV_PRINT_ERRORS;
-
-#define MSM_DMOV_DPRINTF(mask, format, args...) \
-	do { \
-		if ((mask) & msm_dmov_print_mask) \
-			printk(KERN_ERR format, args); \
-	} while (0)
-#define PRINT_ERROR(format, args...) \
-	MSM_DMOV_DPRINTF(MSM_DMOV_PRINT_ERRORS, format, args);
-#define PRINT_IO(format, args...) \
-	MSM_DMOV_DPRINTF(MSM_DMOV_PRINT_IO, format, args);
-#define PRINT_FLOW(format, args...) \
-	MSM_DMOV_DPRINTF(MSM_DMOV_PRINT_FLOW, format, args);
-
-void msm_dmov_stop_cmd(unsigned id, struct msm_dmov_cmd *cmd, int graceful)
-{
-	writel((graceful << 31), DMOV_FLUSH0(id));
-}
-EXPORT_SYMBOL_GPL(msm_dmov_stop_cmd);
-
-void msm_dmov_enqueue_cmd(unsigned id, struct msm_dmov_cmd *cmd)
-{
-	unsigned long irq_flags;
-	unsigned int status;
-
-	spin_lock_irqsave(&msm_dmov_lock, irq_flags);
-	if (!channel_active)
-		clk_enable(msm_dmov_clk);
-	dsb();
-	status = readl(DMOV_STATUS(id));
-	if (list_empty(&ready_commands[id]) &&
-		(status & DMOV_STATUS_CMD_PTR_RDY)) {
-#if 0
-		if (list_empty(&active_commands[id])) {
-			PRINT_FLOW("msm_dmov_enqueue_cmd(%d), enable interrupt\n", id);
-			writel(DMOV_CONFIG_IRQ_EN, DMOV_CONFIG(id));
-		}
-#endif
-		if (cmd->execute_func)
-			cmd->execute_func(cmd);
-		PRINT_IO("msm_dmov_enqueue_cmd(%d), start command, status %x\n", id, status);
-		list_add_tail(&cmd->list, &active_commands[id]);
-		if (!channel_active)
-			enable_irq(INT_ADM_AARM);
-		channel_active |= 1U << id;
-		writel(cmd->cmdptr, DMOV_CMD_PTR(id));
-	} else {
-		if (!channel_active)
-			clk_disable(msm_dmov_clk);
-		if (list_empty(&active_commands[id]))
-			PRINT_ERROR("msm_dmov_enqueue_cmd(%d), error datamover stalled, status %x\n", id, status);
-
-		PRINT_IO("msm_dmov_enqueue_cmd(%d), enqueue command, status %x\n", id, status);
-		list_add_tail(&cmd->list, &ready_commands[id]);
-	}
-	spin_unlock_irqrestore(&msm_dmov_lock, irq_flags);
-}
-EXPORT_SYMBOL_GPL(msm_dmov_enqueue_cmd);
-
-struct msm_dmov_exec_cmdptr_cmd {
-	struct msm_dmov_cmd dmov_cmd;
-	struct completion complete;
-	unsigned id;
-	unsigned int result;
-	struct msm_dmov_errdata err;
-};
-
-static void
-dmov_exec_cmdptr_complete_func(struct msm_dmov_cmd *_cmd,
-			       unsigned int result,
-			       struct msm_dmov_errdata *err)
-{
-	struct msm_dmov_exec_cmdptr_cmd *cmd = container_of(_cmd, struct msm_dmov_exec_cmdptr_cmd, dmov_cmd);
-	cmd->result = result;
-	if (result != 0x80000002 && err)
-		memcpy(&cmd->err, err, sizeof(struct msm_dmov_errdata));
-
-	complete(&cmd->complete);
-}
-
-int msm_dmov_exec_cmd(unsigned id, unsigned int cmdptr)
-{
-	struct msm_dmov_exec_cmdptr_cmd cmd;
-
-	PRINT_FLOW("dmov_exec_cmdptr(%d, %x)\n", id, cmdptr);
-
-	cmd.dmov_cmd.cmdptr = cmdptr;
-	cmd.dmov_cmd.complete_func = dmov_exec_cmdptr_complete_func;
-	cmd.dmov_cmd.execute_func = NULL;
-	cmd.id = id;
-	init_completion(&cmd.complete);
-
-	msm_dmov_enqueue_cmd(id, &cmd.dmov_cmd);
-	wait_for_completion(&cmd.complete);
-
-	if (cmd.result != 0x80000002) {
-		PRINT_ERROR("dmov_exec_cmdptr(%d): ERROR, result: %x\n", id, cmd.result);
-		PRINT_ERROR("dmov_exec_cmdptr(%d):  flush: %x %x %x %x\n",
-			id, cmd.err.flush[0], cmd.err.flush[1], cmd.err.flush[2], cmd.err.flush[3]);
-		return -EIO;
-	}
-	PRINT_FLOW("dmov_exec_cmdptr(%d, %x) done\n", id, cmdptr);
-	return 0;
-}
-
-
-static irqreturn_t msm_datamover_irq_handler(int irq, void *dev_id)
-{
-	unsigned int int_status, mask, id;
-	unsigned long irq_flags;
-	unsigned int ch_status;
-	unsigned int ch_result;
-	struct msm_dmov_cmd *cmd;
-
-	spin_lock_irqsave(&msm_dmov_lock, irq_flags);
-
-	int_status = readl(DMOV_ISR); /* read and clear interrupt */
-	PRINT_FLOW("msm_datamover_irq_handler: DMOV_ISR %x\n", int_status);
-
-	while (int_status) {
-		mask = int_status & -int_status;
-		id = fls(mask) - 1;
-		PRINT_FLOW("msm_datamover_irq_handler %08x %08x id %d\n", int_status, mask, id);
-		int_status &= ~mask;
-		ch_status = readl(DMOV_STATUS(id));
-		if (!(ch_status & DMOV_STATUS_RSLT_VALID)) {
-			PRINT_FLOW("msm_datamover_irq_handler id %d, result not valid %x\n", id, ch_status);
-			continue;
-		}
-		do {
-			ch_result = readl(DMOV_RSLT(id));
-			if (list_empty(&active_commands[id])) {
-				PRINT_ERROR("msm_datamover_irq_handler id %d, got result "
-					"with no active command, status %x, result %x\n",
-					id, ch_status, ch_result);
-				cmd = NULL;
-			} else
-				cmd = list_entry(active_commands[id].next, typeof(*cmd), list);
-			PRINT_FLOW("msm_datamover_irq_handler id %d, status %x, result %x\n", id, ch_status, ch_result);
-			if (ch_result & DMOV_RSLT_DONE) {
-				PRINT_FLOW("msm_datamover_irq_handler id %d, status %x\n",
-					id, ch_status);
-				PRINT_IO("msm_datamover_irq_handler id %d, got result "
-					"for %p, result %x\n", id, cmd, ch_result);
-				if (cmd) {
-					list_del(&cmd->list);
-					dsb();
-					cmd->complete_func(cmd, ch_result, NULL);
-				}
-			}
-			if (ch_result & DMOV_RSLT_FLUSH) {
-				struct msm_dmov_errdata errdata;
-
-				errdata.flush[0] = readl(DMOV_FLUSH0(id));
-				errdata.flush[1] = readl(DMOV_FLUSH1(id));
-				errdata.flush[2] = readl(DMOV_FLUSH2(id));
-				errdata.flush[3] = readl(DMOV_FLUSH3(id));
-				errdata.flush[4] = readl(DMOV_FLUSH4(id));
-				errdata.flush[5] = readl(DMOV_FLUSH5(id));
-				PRINT_FLOW("msm_datamover_irq_handler id %d, status %x\n", id, ch_status);
-				PRINT_FLOW("msm_datamover_irq_handler id %d, flush, result %x, flush0 %x\n", id, ch_result, errdata.flush[0]);
-				if (cmd) {
-					list_del(&cmd->list);
-					dsb();
-					cmd->complete_func(cmd, ch_result, &errdata);
-				}
-			}
-			if (ch_result & DMOV_RSLT_ERROR) {
-				struct msm_dmov_errdata errdata;
-
-				errdata.flush[0] = readl(DMOV_FLUSH0(id));
-				errdata.flush[1] = readl(DMOV_FLUSH1(id));
-				errdata.flush[2] = readl(DMOV_FLUSH2(id));
-				errdata.flush[3] = readl(DMOV_FLUSH3(id));
-				errdata.flush[4] = readl(DMOV_FLUSH4(id));
-				errdata.flush[5] = readl(DMOV_FLUSH5(id));
-
-				PRINT_ERROR("msm_datamover_irq_handler id %d, status %x\n", id, ch_status);
-				PRINT_ERROR("msm_datamover_irq_handler id %d, error, result %x, flush0 %x\n", id, ch_result, errdata.flush[0]);
-				if (cmd) {
-					list_del(&cmd->list);
-					dsb();
-					cmd->complete_func(cmd, ch_result, &errdata);
-				}
-				/* this does not seem to work, once we get an error */
-				/* the datamover will no longer accept commands */
-				writel(0, DMOV_FLUSH0(id));
-			}
-			ch_status = readl(DMOV_STATUS(id));
-			PRINT_FLOW("msm_datamover_irq_handler id %d, status %x\n", id, ch_status);
-			if ((ch_status & DMOV_STATUS_CMD_PTR_RDY) && !list_empty(&ready_commands[id])) {
-				cmd = list_entry(ready_commands[id].next, typeof(*cmd), list);
-				list_move_tail(&cmd->list, &active_commands[id]);
-				if (cmd->execute_func)
-					cmd->execute_func(cmd);
-				PRINT_FLOW("msm_datamover_irq_handler id %d, start command\n", id);
-				writel(cmd->cmdptr, DMOV_CMD_PTR(id));
-			}
-		} while (ch_status & DMOV_STATUS_RSLT_VALID);
-		if (list_empty(&active_commands[id]) && list_empty(&ready_commands[id]))
-			channel_active &= ~(1U << id);
-		PRINT_FLOW("msm_datamover_irq_handler id %d, status %x\n", id, ch_status);
-	}
-
-	if (!channel_active) {
-		disable_irq_nosync(INT_ADM_AARM);
-		clk_disable(msm_dmov_clk);
-	}
-
-	spin_unlock_irqrestore(&msm_dmov_lock, irq_flags);
-	return IRQ_HANDLED;
-}
-
-static int __init msm_init_datamover(void)
-{
-	int i;
-	int ret;
-	struct clk *clk;
-
-	for (i = 0; i < MSM_DMOV_CHANNEL_COUNT; i++) {
-		INIT_LIST_HEAD(&ready_commands[i]);
-		INIT_LIST_HEAD(&active_commands[i]);
-		writel(DMOV_CONFIG_IRQ_EN | DMOV_CONFIG_FORCE_TOP_PTR_RSLT | DMOV_CONFIG_FORCE_FLUSH_RSLT, DMOV_CONFIG(i));
-	}
-	clk = clk_get(NULL, "adm_clk");
-	if (IS_ERR(clk))
-		return PTR_ERR(clk);
-	clk_prepare(clk);
-	msm_dmov_clk = clk;
-	ret = request_irq(INT_ADM_AARM, msm_datamover_irq_handler, 0, "msmdatamover", NULL);
-	if (ret)
-		return ret;
-	disable_irq(INT_ADM_AARM);
-	return 0;
-}
-module_init(msm_init_datamover);
diff --git a/arch/arm/mach-msm/gpiomux-8x50.c b/arch/arm/mach-msm/gpiomux-8x50.c
deleted file mode 100644
index f7a4ea5..0000000
--- a/arch/arm/mach-msm/gpiomux-8x50.c
+++ /dev/null
@@ -1,51 +0,0 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#include "gpiomux.h"
-
-#if defined(CONFIG_MMC_MSM) || defined(CONFIG_MMC_MSM_MODULE)
-	#define SDCC_DAT_0_3_CMD_ACTV_CFG (GPIOMUX_VALID | GPIOMUX_PULL_UP\
-					| GPIOMUX_FUNC_1 | GPIOMUX_DRV_8MA)
-	#define SDCC_CLK_ACTV_CFG (GPIOMUX_VALID | GPIOMUX_PULL_NONE\
-					| GPIOMUX_FUNC_1 | GPIOMUX_DRV_8MA)
-#else
-	#define SDCC_DAT_0_3_CMD_ACTV_CFG 0
-	#define SDCC_CLK_ACTV_CFG 0
-#endif
-
-#define SDC1_SUSPEND_CONFIG (GPIOMUX_VALID | GPIOMUX_PULL_DOWN\
-				| GPIOMUX_FUNC_GPIO | GPIOMUX_DRV_2MA)
-
-struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS] = {
-	[86] = { /* UART3 RX */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_1 | GPIOMUX_VALID,
-	},
-	[87] = { /* UART3 TX */
-		.suspended = GPIOMUX_DRV_2MA | GPIOMUX_PULL_DOWN |
-			     GPIOMUX_FUNC_1 | GPIOMUX_VALID,
-	},
-	/* SDC1 data[3:0] & CMD */
-	[51 ... 55] = {
-		.active = SDCC_DAT_0_3_CMD_ACTV_CFG,
-		.suspended = SDC1_SUSPEND_CONFIG
-	},
-	/* SDC1 CLK */
-	[56] = {
-		.active = SDCC_CLK_ACTV_CFG,
-		.suspended = SDC1_SUSPEND_CONFIG
-	},
-};
diff --git a/arch/arm/mach-msm/gpiomux-v1.h b/arch/arm/mach-msm/gpiomux-v1.h
deleted file mode 100644
index 71d86fe..0000000
--- a/arch/arm/mach-msm/gpiomux-v1.h
+++ /dev/null
@@ -1,67 +0,0 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#ifndef __ARCH_ARM_MACH_MSM_GPIOMUX_V1_H
-#define __ARCH_ARM_MACH_MSM_GPIOMUX_V1_H
-
-#if defined(CONFIG_ARCH_MSM7X30)
-#define GPIOMUX_NGPIOS 182
-#elif defined(CONFIG_ARCH_QSD8X50)
-#define GPIOMUX_NGPIOS 165
-#else
-#define GPIOMUX_NGPIOS 133
-#endif
-
-typedef u32 gpiomux_config_t;
-
-enum {
-	GPIOMUX_DRV_2MA  = 0UL << 17,
-	GPIOMUX_DRV_4MA  = 1UL << 17,
-	GPIOMUX_DRV_6MA  = 2UL << 17,
-	GPIOMUX_DRV_8MA  = 3UL << 17,
-	GPIOMUX_DRV_10MA = 4UL << 17,
-	GPIOMUX_DRV_12MA = 5UL << 17,
-	GPIOMUX_DRV_14MA = 6UL << 17,
-	GPIOMUX_DRV_16MA = 7UL << 17,
-};
-
-enum {
-	GPIOMUX_FUNC_GPIO = 0UL,
-	GPIOMUX_FUNC_1    = 1UL,
-	GPIOMUX_FUNC_2    = 2UL,
-	GPIOMUX_FUNC_3    = 3UL,
-	GPIOMUX_FUNC_4    = 4UL,
-	GPIOMUX_FUNC_5    = 5UL,
-	GPIOMUX_FUNC_6    = 6UL,
-	GPIOMUX_FUNC_7    = 7UL,
-	GPIOMUX_FUNC_8    = 8UL,
-	GPIOMUX_FUNC_9    = 9UL,
-	GPIOMUX_FUNC_A    = 10UL,
-	GPIOMUX_FUNC_B    = 11UL,
-	GPIOMUX_FUNC_C    = 12UL,
-	GPIOMUX_FUNC_D    = 13UL,
-	GPIOMUX_FUNC_E    = 14UL,
-	GPIOMUX_FUNC_F    = 15UL,
-};
-
-enum {
-	GPIOMUX_PULL_NONE   = 0UL << 15,
-	GPIOMUX_PULL_DOWN   = 1UL << 15,
-	GPIOMUX_PULL_KEEPER = 2UL << 15,
-	GPIOMUX_PULL_UP     = 3UL << 15,
-};
-
-#endif
diff --git a/arch/arm/mach-msm/gpiomux.c b/arch/arm/mach-msm/gpiomux.c
deleted file mode 100644
index 2b8e2d2..0000000
--- a/arch/arm/mach-msm/gpiomux.c
+++ /dev/null
@@ -1,111 +0,0 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#include <linux/module.h>
-#include <linux/spinlock.h>
-#include "gpiomux.h"
-#include "proc_comm.h"
-
-static DEFINE_SPINLOCK(gpiomux_lock);
-
-static void __msm_gpiomux_write(unsigned gpio, gpiomux_config_t val)
-{
-	unsigned tlmm_config  = (val & ~GPIOMUX_CTL_MASK) |
-				((gpio & 0x3ff) << 4);
-	unsigned tlmm_disable = 0;
-	int rc;
-
-	rc = msm_proc_comm(PCOM_RPC_GPIO_TLMM_CONFIG_EX,
-			   &tlmm_config, &tlmm_disable);
-	if (rc)
-		pr_err("%s: unexpected proc_comm failure %d: %08x %08x\n",
-		       __func__, rc, tlmm_config, tlmm_disable);
-}
-
-int msm_gpiomux_write(unsigned gpio,
-		      gpiomux_config_t active,
-		      gpiomux_config_t suspended)
-{
-	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
-	unsigned long irq_flags;
-	gpiomux_config_t setting;
-
-	if (gpio >= GPIOMUX_NGPIOS)
-		return -EINVAL;
-
-	spin_lock_irqsave(&gpiomux_lock, irq_flags);
-
-	if (active & GPIOMUX_VALID)
-		cfg->active = active;
-
-	if (suspended & GPIOMUX_VALID)
-		cfg->suspended = suspended;
-
-	setting = cfg->ref ? active : suspended;
-	if (setting & GPIOMUX_VALID)
-		__msm_gpiomux_write(gpio, setting);
-
-	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
-	return 0;
-}
-EXPORT_SYMBOL(msm_gpiomux_write);
-
-int msm_gpiomux_get(unsigned gpio)
-{
-	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
-	unsigned long irq_flags;
-
-	if (gpio >= GPIOMUX_NGPIOS)
-		return -EINVAL;
-
-	spin_lock_irqsave(&gpiomux_lock, irq_flags);
-	if (cfg->ref++ == 0 && cfg->active & GPIOMUX_VALID)
-		__msm_gpiomux_write(gpio, cfg->active);
-	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
-	return 0;
-}
-EXPORT_SYMBOL(msm_gpiomux_get);
-
-int msm_gpiomux_put(unsigned gpio)
-{
-	struct msm_gpiomux_config *cfg = msm_gpiomux_configs + gpio;
-	unsigned long irq_flags;
-
-	if (gpio >= GPIOMUX_NGPIOS)
-		return -EINVAL;
-
-	spin_lock_irqsave(&gpiomux_lock, irq_flags);
-	BUG_ON(cfg->ref == 0);
-	if (--cfg->ref == 0 && cfg->suspended & GPIOMUX_VALID)
-		__msm_gpiomux_write(gpio, cfg->suspended);
-	spin_unlock_irqrestore(&gpiomux_lock, irq_flags);
-	return 0;
-}
-EXPORT_SYMBOL(msm_gpiomux_put);
-
-static int __init gpiomux_init(void)
-{
-	unsigned n;
-
-	for (n = 0; n < GPIOMUX_NGPIOS; ++n) {
-		msm_gpiomux_configs[n].ref = 0;
-		if (!(msm_gpiomux_configs[n].suspended & GPIOMUX_VALID))
-			continue;
-		__msm_gpiomux_write(n, msm_gpiomux_configs[n].suspended);
-	}
-	return 0;
-}
-postcore_initcall(gpiomux_init);
diff --git a/arch/arm/mach-msm/gpiomux.h b/arch/arm/mach-msm/gpiomux.h
deleted file mode 100644
index 4410d77..0000000
--- a/arch/arm/mach-msm/gpiomux.h
+++ /dev/null
@@ -1,84 +0,0 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#ifndef __ARCH_ARM_MACH_MSM_GPIOMUX_H
-#define __ARCH_ARM_MACH_MSM_GPIOMUX_H
-
-#include <linux/bitops.h>
-#include <linux/errno.h>
-#include <mach/msm_gpiomux.h>
-#include "gpiomux-v1.h"
-
-/**
- * struct msm_gpiomux_config: gpiomux settings for one gpio line.
- *
- * A complete gpiomux config is the bitwise-or of a drive-strength,
- * function, and pull.  For functions other than GPIO, the OE
- * is hard-wired according to the function.  For GPIO mode,
- * OE is controlled by gpiolib.
- *
- * Available settings differ by target; see the gpiomux header
- * specific to your target arch for available configurations.
- *
- * @active: The configuration to be installed when the line is
- * active, or its reference count is > 0.
- * @suspended: The configuration to be installed when the line
- * is suspended, or its reference count is 0.
- * @ref: The reference count of the line.  For internal use of
- * the gpiomux framework only.
- */
-struct msm_gpiomux_config {
-	gpiomux_config_t active;
-	gpiomux_config_t suspended;
-	unsigned         ref;
-};
-
-/**
- * @GPIOMUX_VALID:	If set, the config field contains 'good data'.
- *                      The absence of this bit will prevent the gpiomux
- *			system from applying the configuration under all
- *			circumstances.
- */
-enum {
-	GPIOMUX_VALID	 = BIT(sizeof(gpiomux_config_t) * BITS_PER_BYTE - 1),
-	GPIOMUX_CTL_MASK = GPIOMUX_VALID,
-};
-
-#ifdef CONFIG_MSM_GPIOMUX
-
-/* Each architecture must provide its own instance of this table.
- * To avoid having gpiomux manage any given gpio, one or both of
- * the entries can avoid setting GPIOMUX_VALID - the absence
- * of that flag will prevent the configuration from being applied
- * during state transitions.
- */
-extern struct msm_gpiomux_config msm_gpiomux_configs[GPIOMUX_NGPIOS];
-
-/* Install a new configuration to the gpio line.  To avoid overwriting
- * a configuration, leave the VALID bit out.
- */
-int msm_gpiomux_write(unsigned gpio,
-		      gpiomux_config_t active,
-		      gpiomux_config_t suspended);
-#else
-static inline int msm_gpiomux_write(unsigned gpio,
-				    gpiomux_config_t active,
-				    gpiomux_config_t suspended)
-{
-	return -ENOSYS;
-}
-#endif
-#endif
diff --git a/arch/arm/mach-msm/include/mach/clk.h b/arch/arm/mach-msm/include/mach/clk.h
deleted file mode 100644
index fd4f4a7..0000000
--- a/arch/arm/mach-msm/include/mach/clk.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-#ifndef __MACH_CLK_H
-#define __MACH_CLK_H
-
-/* Magic rate value for use with PM QOS to request the board's maximum
- * supported AXI rate. PM QOS will only pass positive s32 rate values
- * through to the clock driver, so INT_MAX is used.
- */
-#define MSM_AXI_MAX_FREQ	LONG_MAX
-
-enum clk_reset_action {
-	CLK_RESET_DEASSERT	= 0,
-	CLK_RESET_ASSERT	= 1
-};
-
-struct clk;
-
-/* Assert/Deassert reset to a hardware block associated with a clock */
-int clk_reset(struct clk *clk, enum clk_reset_action action);
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/dma.h b/arch/arm/mach-msm/include/mach/dma.h
deleted file mode 100644
index a72d48d..0000000
--- a/arch/arm/mach-msm/include/mach/dma.h
+++ /dev/null
@@ -1,151 +0,0 @@
-/* linux/include/asm-arm/arch-msm/dma.h
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_DMA_H
-
-#include <linux/list.h>
-
-struct msm_dmov_errdata {
-	uint32_t flush[6];
-};
-
-struct msm_dmov_cmd {
-	struct list_head list;
-	unsigned int cmdptr;
-	void (*complete_func)(struct msm_dmov_cmd *cmd,
-			      unsigned int result,
-			      struct msm_dmov_errdata *err);
-	void (*execute_func)(struct msm_dmov_cmd *cmd);
-	void *data;
-};
-
-#ifndef CONFIG_ARCH_MSM8X60
-void msm_dmov_enqueue_cmd(unsigned id, struct msm_dmov_cmd *cmd);
-void msm_dmov_stop_cmd(unsigned id, struct msm_dmov_cmd *cmd, int graceful);
-int msm_dmov_exec_cmd(unsigned id, unsigned int cmdptr);
-#else
-static inline
-void msm_dmov_enqueue_cmd(unsigned id, struct msm_dmov_cmd *cmd) { }
-static inline
-void msm_dmov_stop_cmd(unsigned id, struct msm_dmov_cmd *cmd, int graceful) { }
-static inline
-int msm_dmov_exec_cmd(unsigned id, unsigned int cmdptr) { return -EIO; }
-#endif
-
-#define DMOV_CMD_LIST         (0 << 29) /* does not work */
-#define DMOV_CMD_PTR_LIST     (1 << 29) /* works */
-#define DMOV_CMD_INPUT_CFG    (2 << 29) /* untested */
-#define DMOV_CMD_OUTPUT_CFG   (3 << 29) /* untested */
-#define DMOV_CMD_ADDR(addr)   ((addr) >> 3)
-
-#define DMOV_RSLT_VALID       (1 << 31) /* 0 == host has empties result fifo */
-#define DMOV_RSLT_ERROR       (1 << 3)
-#define DMOV_RSLT_FLUSH       (1 << 2)
-#define DMOV_RSLT_DONE        (1 << 1)  /* top pointer done */
-#define DMOV_RSLT_USER        (1 << 0)  /* command with FR force result */
-
-#define DMOV_STATUS_RSLT_COUNT(n)    (((n) >> 29))
-#define DMOV_STATUS_CMD_COUNT(n)     (((n) >> 27) & 3)
-#define DMOV_STATUS_RSLT_VALID       (1 << 1)
-#define DMOV_STATUS_CMD_PTR_RDY      (1 << 0)
-
-#define DMOV_CONFIG_FORCE_TOP_PTR_RSLT (1 << 2)
-#define DMOV_CONFIG_FORCE_FLUSH_RSLT   (1 << 1)
-#define DMOV_CONFIG_IRQ_EN             (1 << 0)
-
-/* channel assignments */
-
-#define DMOV_NAND_CHAN        7
-#define DMOV_NAND_CRCI_CMD    5
-#define DMOV_NAND_CRCI_DATA   4
-
-#define DMOV_SDC1_CHAN        8
-#define DMOV_SDC1_CRCI        6
-
-#define DMOV_SDC2_CHAN        8
-#define DMOV_SDC2_CRCI        7
-
-#define DMOV_TSIF_CHAN        10
-#define DMOV_TSIF_CRCI        10
-
-#define DMOV_USB_CHAN         11
-
-/* no client rate control ifc (eg, ram) */
-#define DMOV_NONE_CRCI        0
-
-
-/* If the CMD_PTR register has CMD_PTR_LIST selected, the data mover
- * is going to walk a list of 32bit pointers as described below.  Each
- * pointer points to a *array* of dmov_s, etc structs.  The last pointer
- * in the list is marked with CMD_PTR_LP.  The last struct in each array
- * is marked with CMD_LC (see below).
- */
-#define CMD_PTR_ADDR(addr)  ((addr) >> 3)
-#define CMD_PTR_LP          (1 << 31) /* last pointer */
-#define CMD_PTR_PT          (3 << 29) /* ? */
-
-/* Single Item Mode */
-typedef struct {
-	unsigned cmd;
-	unsigned src;
-	unsigned dst;
-	unsigned len;
-} dmov_s;
-
-/* Scatter/Gather Mode */
-typedef struct {
-	unsigned cmd;
-	unsigned src_dscr;
-	unsigned dst_dscr;
-	unsigned _reserved;
-} dmov_sg;
-
-/* Box mode */
-typedef struct {
-	uint32_t cmd;
-	uint32_t src_row_addr;
-	uint32_t dst_row_addr;
-	uint32_t src_dst_len;
-	uint32_t num_rows;
-	uint32_t row_offset;
-} dmov_box;
-
-/* bits for the cmd field of the above structures */
-
-#define CMD_LC      (1 << 31)  /* last command */
-#define CMD_FR      (1 << 22)  /* force result -- does not work? */
-#define CMD_OCU     (1 << 21)  /* other channel unblock */
-#define CMD_OCB     (1 << 20)  /* other channel block */
-#define CMD_TCB     (1 << 19)  /* ? */
-#define CMD_DAH     (1 << 18)  /* destination address hold -- does not work?*/
-#define CMD_SAH     (1 << 17)  /* source address hold -- does not work? */
-
-#define CMD_MODE_SINGLE     (0 << 0) /* dmov_s structure used */
-#define CMD_MODE_SG         (1 << 0) /* untested */
-#define CMD_MODE_IND_SG     (2 << 0) /* untested */
-#define CMD_MODE_BOX        (3 << 0) /* untested */
-
-#define CMD_DST_SWAP_BYTES  (1 << 14) /* exchange each byte n with byte n+1 */
-#define CMD_DST_SWAP_SHORTS (1 << 15) /* exchange each short n with short n+1 */
-#define CMD_DST_SWAP_WORDS  (1 << 16) /* exchange each word n with word n+1 */
-
-#define CMD_SRC_SWAP_BYTES  (1 << 11) /* exchange each byte n with byte n+1 */
-#define CMD_SRC_SWAP_SHORTS (1 << 12) /* exchange each short n with short n+1 */
-#define CMD_SRC_SWAP_WORDS  (1 << 13) /* exchange each word n with word n+1 */
-
-#define CMD_DST_CRCI(n)     (((n) & 15) << 7)
-#define CMD_SRC_CRCI(n)     (((n) & 15) << 3)
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/entry-macro.S b/arch/arm/mach-msm/include/mach/entry-macro.S
deleted file mode 100644
index f2ae9087..0000000
--- a/arch/arm/mach-msm/include/mach/entry-macro.S
+++ /dev/null
@@ -1,36 +0,0 @@
-/* Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- *
- */
-
-#if !defined(CONFIG_ARM_GIC)
-#include <mach/msm_iomap.h>
-
-	.macro	get_irqnr_preamble, base, tmp
-	@ enable imprecise aborts
-	cpsie	a
-	mov	\base, #MSM_VIC_BASE
-	.endm
-
-	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-	@ 0xD0 has irq# or old irq# if the irq has been handled
-	@ 0xD4 has irq# or -1 if none pending *but* if you just
-	@ read 0xD4 you never get the first irq for some reason
-	ldr	\irqnr, [\base, #0xD0]
-	ldr	\irqnr, [\base, #0xD4]
-	cmp	\irqnr, #0xffffffff
-	.endm
-#endif
diff --git a/arch/arm/mach-msm/include/mach/hardware.h b/arch/arm/mach-msm/include/mach/hardware.h
deleted file mode 100644
index 2d12609..0000000
--- a/arch/arm/mach-msm/include/mach/hardware.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* arch/arm/mach-msm/include/mach/hardware.h
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_HARDWARE_H
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/irqs-7x00.h b/arch/arm/mach-msm/include/mach/irqs-7x00.h
deleted file mode 100644
index f1fe706..0000000
--- a/arch/arm/mach-msm/include/mach/irqs-7x00.h
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- */
-
-#ifndef __ASM_ARCH_MSM_IRQS_7X00_H
-#define __ASM_ARCH_MSM_IRQS_7X00_H
-
-/* MSM ARM11 Interrupt Numbers */
-/* See 80-VE113-1 A, pp219-221     */
-
-#define INT_A9_M2A_0         0
-#define INT_A9_M2A_1         1
-#define INT_A9_M2A_2         2
-#define INT_A9_M2A_3         3
-#define INT_A9_M2A_4         4
-#define INT_A9_M2A_5         5
-#define INT_A9_M2A_6         6
-#define INT_GP_TIMER_EXP     7
-#define INT_DEBUG_TIMER_EXP  8
-#define INT_UART1            9
-#define INT_UART2            10
-#define INT_UART3            11
-#define INT_UART1_RX         12
-#define INT_UART2_RX         13
-#define INT_UART3_RX         14
-#define INT_USB_OTG          15
-#define INT_MDDI_PRI         16
-#define INT_MDDI_EXT         17
-#define INT_MDDI_CLIENT      18
-#define INT_MDP              19
-#define INT_GRAPHICS         20
-#define INT_ADM_AARM         21
-#define INT_ADSP_A11         22
-#define INT_ADSP_A9_A11      23
-#define INT_SDC1_0           24
-#define INT_SDC1_1           25
-#define INT_SDC2_0           26
-#define INT_SDC2_1           27
-#define INT_KEYSENSE         28
-#define INT_TCHSCRN_SSBI     29
-#define INT_TCHSCRN1         30
-#define INT_TCHSCRN2         31
-
-#define INT_GPIO_GROUP1      (32 + 0)
-#define INT_GPIO_GROUP2      (32 + 1)
-#define INT_PWB_I2C          (32 + 2)
-#define INT_SOFTRESET        (32 + 3)
-#define INT_NAND_WR_ER_DONE  (32 + 4)
-#define INT_NAND_OP_DONE     (32 + 5)
-#define INT_PBUS_ARM11       (32 + 6)
-#define INT_AXI_MPU_SMI      (32 + 7)
-#define INT_AXI_MPU_EBI1     (32 + 8)
-#define INT_AD_HSSD          (32 + 9)
-#define INT_ARM11_PMU        (32 + 10)
-#define INT_ARM11_DMA        (32 + 11)
-#define INT_TSIF_IRQ         (32 + 12)
-#define INT_UART1DM_IRQ      (32 + 13)
-#define INT_UART1DM_RX       (32 + 14)
-#define INT_USB_HS           (32 + 15)
-#define INT_SDC3_0           (32 + 16)
-#define INT_SDC3_1           (32 + 17)
-#define INT_SDC4_0           (32 + 18)
-#define INT_SDC4_1           (32 + 19)
-#define INT_UART2DM_RX       (32 + 20)
-#define INT_UART2DM_IRQ      (32 + 21)
-
-/* 22-31 are reserved */
-
-#define NR_MSM_IRQS 64
-#define NR_GPIO_IRQS 122
-#define NR_BOARD_IRQS 64
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/irqs-7x30.h b/arch/arm/mach-msm/include/mach/irqs-7x30.h
deleted file mode 100644
index 1f15902..0000000
--- a/arch/arm/mach-msm/include/mach/irqs-7x30.h
+++ /dev/null
@@ -1,153 +0,0 @@
-/* Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MSM_IRQS_7X30_H
-#define __ASM_ARCH_MSM_IRQS_7X30_H
-
-/* MSM ACPU Interrupt Numbers */
-
-#define INT_DEBUG_TIMER_EXP	0
-#define INT_GPT0_TIMER_EXP	1
-#define INT_GPT1_TIMER_EXP	2
-#define INT_WDT0_ACCSCSSBARK	3
-#define INT_WDT1_ACCSCSSBARK	4
-#define INT_AVS_SVIC		5
-#define INT_AVS_SVIC_SW_DONE	6
-#define INT_SC_DBG_RX_FULL	7
-#define INT_SC_DBG_TX_EMPTY	8
-#define INT_ARM11_PM		9
-#define INT_AVS_REQ_DOWN	10
-#define INT_AVS_REQ_UP		11
-#define INT_SC_ACG		12
-/* SCSS_VICFIQSTS0[13:15] are RESERVED */
-#define INT_L2_SVICCPUIRPTREQ	16
-#define INT_L2_SVICDMANSIRPTREQ 17
-#define INT_L2_SVICDMASIRPTREQ  18
-#define INT_L2_SVICSLVIRPTREQ	19
-#define INT_AD5A_MPROC_APPS_0	20
-#define INT_AD5A_MPROC_APPS_1	21
-#define INT_A9_M2A_0		22
-#define INT_A9_M2A_1		23
-#define INT_A9_M2A_2		24
-#define INT_A9_M2A_3		25
-#define INT_A9_M2A_4		26
-#define INT_A9_M2A_5		27
-#define INT_A9_M2A_6		28
-#define INT_A9_M2A_7		29
-#define INT_A9_M2A_8		30
-#define INT_A9_M2A_9		31
-
-#define INT_AXI_EBI1_SC		(32 + 0)
-#define INT_IMEM_ERR		(32 + 1)
-#define INT_AXI_EBI0_SC		(32 + 2)
-#define INT_PBUS_SC_IRQC	(32 + 3)
-#define INT_PERPH_BUS_BPM	(32 + 4)
-#define INT_CC_TEMP_SENSE	(32 + 5)
-#define INT_UXMC_EBI0		(32 + 6)
-#define INT_UXMC_EBI1		(32 + 7)
-#define INT_EBI2_OP_DONE	(32 + 8)
-#define INT_EBI2_WR_ER_DONE	(32 + 9)
-#define INT_TCSR_SPSS_CE	(32 + 10)
-#define INT_EMDH		(32 + 11)
-#define INT_PMDH		(32 + 12)
-#define INT_MDC			(32 + 13)
-#define INT_MIDI_TO_SUPSS	(32 + 14)
-#define INT_LPA_2		(32 + 15)
-#define INT_GPIO_GROUP1_SECURE	(32 + 16)
-#define INT_GPIO_GROUP2_SECURE	(32 + 17)
-#define INT_GPIO_GROUP1		(32 + 18)
-#define INT_GPIO_GROUP2		(32 + 19)
-#define INT_MPRPH_SOFTRESET	(32 + 20)
-#define INT_PWB_I2C		(32 + 21)
-#define INT_PWB_I2C_2		(32 + 22)
-#define INT_TSSC_SAMPLE		(32 + 23)
-#define INT_TSSC_PENUP		(32 + 24)
-#define INT_TCHSCRN_SSBI	(32 + 25)
-#define INT_FM_RDS		(32 + 26)
-#define INT_KEYSENSE 		(32 + 27)
-#define INT_USB_OTG_HS		(32 + 28)
-#define INT_USB_OTG_HS2		(32 + 29)
-#define INT_USB_OTG_HS3		(32 + 30)
-#define INT_CSI			(32 + 31)
-
-#define INT_SPI_OUTPUT		(64 + 0)
-#define INT_SPI_INPUT		(64 + 1)
-#define INT_SPI_ERROR		(64 + 2)
-#define INT_UART1		(64 + 3)
-#define INT_UART1_RX		(64 + 4)
-#define INT_UART2		(64 + 5)
-#define INT_UART2_RX		(64 + 6)
-#define INT_UART3		(64 + 7)
-#define INT_UART3_RX		(64 + 8)
-#define INT_UART1DM_IRQ		(64 + 9)
-#define INT_UART1DM_RX		(64 + 10)
-#define INT_UART2DM_IRQ		(64 + 11)
-#define INT_UART2DM_RX		(64 + 12)
-#define INT_TSIF		(64 + 13)
-#define INT_ADM_SC1		(64 + 14)
-#define INT_ADM_SC2		(64 + 15)
-#define INT_MDP			(64 + 16)
-#define INT_VPE			(64 + 17)
-#define INT_GRP_2D		(64 + 18)
-#define INT_GRP_3D		(64 + 19)
-#define INT_ROTATOR		(64 + 20)
-#define INT_MFC720		(64 + 21)
-#define INT_JPEG		(64 + 22)
-#define INT_VFE			(64 + 23)
-#define INT_TV_ENC		(64 + 24)
-#define INT_PMIC_SSBI		(64 + 25)
-#define INT_MPM_1		(64 + 26)
-#define INT_TCSR_SPSS_SAMPLE	(64 + 27)
-#define INT_TCSR_SPSS_PENUP	(64 + 28)
-#define INT_MPM_2		(64 + 29)
-#define INT_SDC1_0		(64 + 30)
-#define INT_SDC1_1		(64 + 31)
-
-#define INT_SDC3_0		(96 + 0)
-#define INT_SDC3_1		(96 + 1)
-#define INT_SDC2_0		(96 + 2)
-#define INT_SDC2_1		(96 + 3)
-#define INT_SDC4_0		(96 + 4)
-#define INT_SDC4_1		(96 + 5)
-#define INT_PWB_QUP_IN		(96 + 6)
-#define INT_PWB_QUP_OUT		(96 + 7)
-#define INT_PWB_QUP_ERR		(96 + 8)
-#define INT_SCSS_WDT0_BITE	(96 + 9)
-/* SCSS_VICFIQSTS3[10:31] are RESERVED */
-
-/* Retrofit universal macro names */
-#define INT_ADM_AARM		INT_ADM_SC2
-#define INT_USB_HS   		INT_USB_OTG_HS
-#define INT_USB_OTG   		INT_USB_OTG_HS
-#define INT_TCHSCRN1 		INT_TSSC_SAMPLE
-#define INT_TCHSCRN2 		INT_TSSC_PENUP
-#define INT_GP_TIMER_EXP 	INT_GPT0_TIMER_EXP
-#define INT_ADSP_A11 		INT_AD5A_MPROC_APPS_0
-#define INT_ADSP_A9_A11 	INT_AD5A_MPROC_APPS_1
-#define INT_MDDI_EXT		INT_EMDH
-#define INT_MDDI_PRI		INT_PMDH
-#define INT_MDDI_CLIENT		INT_MDC
-#define INT_NAND_WR_ER_DONE	INT_EBI2_WR_ER_DONE
-#define INT_NAND_OP_DONE	INT_EBI2_OP_DONE
-
-#define NR_MSM_IRQS		128
-#define NR_GPIO_IRQS		182
-#define PMIC8058_IRQ_BASE	(NR_MSM_IRQS + NR_GPIO_IRQS)
-#define NR_PMIC8058_GPIO_IRQS	40
-#define NR_PMIC8058_MPP_IRQS	12
-#define NR_PMIC8058_MISC_IRQS	8
-#define NR_PMIC8058_IRQS	(NR_PMIC8058_GPIO_IRQS +\
-				NR_PMIC8058_MPP_IRQS +\
-				NR_PMIC8058_MISC_IRQS)
-#define NR_BOARD_IRQS		NR_PMIC8058_IRQS
-
-#endif /* __ASM_ARCH_MSM_IRQS_7X30_H */
diff --git a/arch/arm/mach-msm/include/mach/irqs-8x50.h b/arch/arm/mach-msm/include/mach/irqs-8x50.h
deleted file mode 100644
index 26adbe0..0000000
--- a/arch/arm/mach-msm/include/mach/irqs-8x50.h
+++ /dev/null
@@ -1,88 +0,0 @@
-/* Copyright (c) 2008-2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MSM_IRQS_8XXX_H
-#define __ASM_ARCH_MSM_IRQS_8XXX_H
-
-/* MSM ACPU Interrupt Numbers */
-
-#define INT_A9_M2A_0         0
-#define INT_A9_M2A_1         1
-#define INT_A9_M2A_2         2
-#define INT_A9_M2A_3         3
-#define INT_A9_M2A_4         4
-#define INT_A9_M2A_5         5
-#define INT_A9_M2A_6         6
-#define INT_GP_TIMER_EXP     7
-#define INT_DEBUG_TIMER_EXP  8
-#define INT_SIRC_0           9
-#define INT_SDC3_0           10
-#define INT_SDC3_1           11
-#define INT_SDC4_0           12
-#define INT_SDC4_1           13
-#define INT_AD6_EXT_VFR      14
-#define INT_USB_OTG          15
-#define INT_MDDI_PRI         16
-#define INT_MDDI_EXT         17
-#define INT_MDDI_CLIENT      18
-#define INT_MDP              19
-#define INT_GRAPHICS         20
-#define INT_ADM_AARM         21
-#define INT_ADSP_A11         22
-#define INT_ADSP_A9_A11      23
-#define INT_SDC1_0           24
-#define INT_SDC1_1           25
-#define INT_SDC2_0           26
-#define INT_SDC2_1           27
-#define INT_KEYSENSE         28
-#define INT_TCHSCRN_SSBI     29
-#define INT_TCHSCRN1         30
-#define INT_TCHSCRN2         31
-
-#define INT_TCSR_MPRPH_SC1   (32 + 0)
-#define INT_USB_FS2          (32 + 1)
-#define INT_PWB_I2C          (32 + 2)
-#define INT_SOFTRESET        (32 + 3)
-#define INT_NAND_WR_ER_DONE  (32 + 4)
-#define INT_NAND_OP_DONE     (32 + 5)
-#define INT_TCSR_MPRPH_SC2   (32 + 6)
-#define INT_OP_PEN           (32 + 7)
-#define INT_AD_HSSD          (32 + 8)
-#define INT_ARM11_PM         (32 + 9)
-#define INT_SDMA_NON_SECURE  (32 + 10)
-#define INT_TSIF_IRQ         (32 + 11)
-#define INT_UART1DM_IRQ      (32 + 12)
-#define INT_UART1DM_RX       (32 + 13)
-#define INT_SDMA_SECURE      (32 + 14)
-#define INT_SI2S_SLAVE       (32 + 15)
-#define INT_SC_I2CPU         (32 + 16)
-#define INT_SC_DBG_RDTRFULL  (32 + 17)
-#define INT_SC_DBG_WDTRFULL  (32 + 18)
-#define INT_SCPLL_CTL_DONE   (32 + 19)
-#define INT_UART2DM_IRQ      (32 + 20)
-#define INT_UART2DM_RX       (32 + 21)
-#define INT_VDC_MEC          (32 + 22)
-#define INT_VDC_DB           (32 + 23)
-#define INT_VDC_AXI          (32 + 24)
-#define INT_VFE              (32 + 25)
-#define INT_USB_HS           (32 + 26)
-#define INT_AUDIO_OUT0       (32 + 27)
-#define INT_AUDIO_OUT1       (32 + 28)
-#define INT_CRYPTO           (32 + 29)
-#define INT_AD6M_IDLE        (32 + 30)
-#define INT_SIRC_1           (32 + 31)
-
-#define NR_GPIO_IRQS 165
-#define NR_MSM_IRQS 64
-#define NR_BOARD_IRQS 64
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/irqs.h b/arch/arm/mach-msm/include/mach/irqs.h
deleted file mode 100644
index 164d355..0000000
--- a/arch/arm/mach-msm/include/mach/irqs.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IRQS_H
-#define __ASM_ARCH_MSM_IRQS_H
-
-#define MSM_IRQ_BIT(irq)     (1 << ((irq) & 31))
-
-#if defined(CONFIG_ARCH_MSM7X30)
-#include "irqs-7x30.h"
-#elif defined(CONFIG_ARCH_QSD8X50)
-#include "irqs-8x50.h"
-#include "sirc.h"
-#elif defined(CONFIG_ARCH_MSM_ARM11)
-#include "irqs-7x00.h"
-#else
-#error "Unknown architecture specification"
-#endif
-
-#define NR_IRQS (NR_MSM_IRQS + NR_GPIO_IRQS + NR_BOARD_IRQS)
-#define MSM_GPIO_TO_INT(n) (NR_MSM_IRQS + (n))
-#define MSM_INT_TO_REG(base, irq) (base + irq / 32)
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_gpiomux.h b/arch/arm/mach-msm/include/mach/msm_gpiomux.h
deleted file mode 100644
index 0c7d393..0000000
--- a/arch/arm/mach-msm/include/mach/msm_gpiomux.h
+++ /dev/null
@@ -1,38 +0,0 @@
-/* Copyright (c) 2011, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef _LINUX_MSM_GPIOMUX_H
-#define _LINUX_MSM_GPIOMUX_H
-
-#ifdef CONFIG_MSM_GPIOMUX
-
-/* Increment a gpio's reference count, possibly activating the line. */
-int __must_check msm_gpiomux_get(unsigned gpio);
-
-/* Decrement a gpio's reference count, possibly suspending the line. */
-int msm_gpiomux_put(unsigned gpio);
-
-#else
-
-static inline int __must_check msm_gpiomux_get(unsigned gpio)
-{
-	return -ENOSYS;
-}
-
-static inline int msm_gpiomux_put(unsigned gpio)
-{
-	return -ENOSYS;
-}
-
-#endif
-
-#endif /* _LINUX_MSM_GPIOMUX_H */
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h b/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h
deleted file mode 100644
index 67dc0e9..0000000
--- a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h
+++ /dev/null
@@ -1,108 +0,0 @@
-/* arch/arm/mach-msm/include/mach/msm_iomap.h
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2011, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- *
- * The MSM peripherals are spread all over across 768MB of physical
- * space, which makes just having a simple IO_ADDRESS macro to slide
- * them into the right virtual location rough.  Instead, we will
- * provide a master phys->virt mapping for peripherals here.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IOMAP_7X00_H
-#define __ASM_ARCH_MSM_IOMAP_7X00_H
-
-#include <asm/sizes.h>
-
-/* Physical base address and size of peripherals.
- * Ordered by the virtual base addresses they will be mapped at.
- *
- * MSM_VIC_BASE must be an value that can be loaded via a "mov"
- * instruction, otherwise entry-macro.S will not compile.
- *
- * If you add or remove entries here, you'll want to edit the
- * msm_io_desc array in arch/arm/mach-msm/io.c to reflect your
- * changes.
- *
- */
-
-#define MSM_VIC_BASE          IOMEM(0xE0000000)
-#define MSM_VIC_PHYS          0xC0000000
-#define MSM_VIC_SIZE          SZ_4K
-
-#define MSM7X00_CSR_PHYS      0xC0100000
-#define MSM7X00_CSR_SIZE      SZ_4K
-
-#define MSM_DMOV_BASE         IOMEM(0xE0002000)
-#define MSM_DMOV_PHYS         0xA9700000
-#define MSM_DMOV_SIZE         SZ_4K
-
-#define MSM7X00_GPIO1_PHYS        0xA9200000
-#define MSM7X00_GPIO1_SIZE        SZ_4K
-
-#define MSM7X00_GPIO2_PHYS        0xA9300000
-#define MSM7X00_GPIO2_SIZE        SZ_4K
-
-#define MSM_CLK_CTL_BASE      IOMEM(0xE0005000)
-#define MSM_CLK_CTL_PHYS      0xA8600000
-#define MSM_CLK_CTL_SIZE      SZ_4K
-
-#define MSM_SHARED_RAM_BASE   IOMEM(0xE0100000)
-#define MSM_SHARED_RAM_PHYS   0x01F00000
-#define MSM_SHARED_RAM_SIZE   SZ_1M
-
-#define MSM_UART1_PHYS        0xA9A00000
-#define MSM_UART1_SIZE        SZ_4K
-
-#define MSM_UART2_PHYS        0xA9B00000
-#define MSM_UART2_SIZE        SZ_4K
-
-#define MSM_UART3_PHYS        0xA9C00000
-#define MSM_UART3_SIZE        SZ_4K
-
-#define MSM_SDC1_PHYS         0xA0400000
-#define MSM_SDC1_SIZE         SZ_4K
-
-#define MSM_SDC2_PHYS         0xA0500000
-#define MSM_SDC2_SIZE         SZ_4K
-
-#define MSM_SDC3_PHYS         0xA0600000
-#define MSM_SDC3_SIZE         SZ_4K
-
-#define MSM_SDC4_PHYS         0xA0700000
-#define MSM_SDC4_SIZE         SZ_4K
-
-#define MSM_I2C_PHYS          0xA9900000
-#define MSM_I2C_SIZE          SZ_4K
-
-#define MSM_HSUSB_PHYS        0xA0800000
-#define MSM_HSUSB_SIZE        SZ_4K
-
-#define MSM_PMDH_PHYS         0xAA600000
-#define MSM_PMDH_SIZE         SZ_4K
-
-#define MSM_EMDH_PHYS         0xAA700000
-#define MSM_EMDH_SIZE         SZ_4K
-
-#define MSM_MDP_PHYS          0xAA200000
-#define MSM_MDP_SIZE          0x000F0000
-
-#define MSM_MDC_PHYS	      0xAA500000
-#define MSM_MDC_SIZE	      SZ_1M
-
-#define MSM_AD5_PHYS          0xAC000000
-#define MSM_AD5_SIZE          (SZ_1M*13)
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h b/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h
deleted file mode 100644
index 198202c..0000000
--- a/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h
+++ /dev/null
@@ -1,103 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2008-2011 Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- *
- * The MSM peripherals are spread all over across 768MB of physical
- * space, which makes just having a simple IO_ADDRESS macro to slide
- * them into the right virtual location rough.  Instead, we will
- * provide a master phys->virt mapping for peripherals here.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IOMAP_7X30_H
-#define __ASM_ARCH_MSM_IOMAP_7X30_H
-
-/* Physical base address and size of peripherals.
- * Ordered by the virtual base addresses they will be mapped at.
- *
- * MSM_VIC_BASE must be an value that can be loaded via a "mov"
- * instruction, otherwise entry-macro.S will not compile.
- *
- * If you add or remove entries here, you'll want to edit the
- * msm_io_desc array in arch/arm/mach-msm/io.c to reflect your
- * changes.
- *
- */
-
-#define MSM_VIC_BASE          IOMEM(0xE0000000)
-#define MSM_VIC_PHYS          0xC0080000
-#define MSM_VIC_SIZE          SZ_4K
-
-#define MSM7X30_CSR_PHYS      0xC0100000
-#define MSM7X30_CSR_SIZE      SZ_4K
-
-#define MSM_DMOV_BASE         IOMEM(0xE0002000)
-#define MSM_DMOV_PHYS         0xAC400000
-#define MSM_DMOV_SIZE         SZ_4K
-
-#define MSM7X30_GPIO1_PHYS        0xAC001000
-#define MSM7X30_GPIO1_SIZE        SZ_4K
-
-#define MSM7X30_GPIO2_PHYS        0xAC101000
-#define MSM7X30_GPIO2_SIZE        SZ_4K
-
-#define MSM_CLK_CTL_BASE      IOMEM(0xE0005000)
-#define MSM_CLK_CTL_PHYS      0xAB800000
-#define MSM_CLK_CTL_SIZE      SZ_4K
-
-#define MSM_CLK_CTL_SH2_BASE  IOMEM(0xE0006000)
-#define MSM_CLK_CTL_SH2_PHYS  0xABA01000
-#define MSM_CLK_CTL_SH2_SIZE  SZ_4K
-
-#define MSM_ACC_BASE          IOMEM(0xE0007000)
-#define MSM_ACC_PHYS          0xC0101000
-#define MSM_ACC_SIZE          SZ_4K
-
-#define MSM_SAW_BASE          IOMEM(0xE0008000)
-#define MSM_SAW_PHYS          0xC0102000
-#define MSM_SAW_SIZE          SZ_4K
-
-#define MSM_GCC_BASE	      IOMEM(0xE0009000)
-#define MSM_GCC_PHYS	      0xC0182000
-#define MSM_GCC_SIZE	      SZ_4K
-
-#define MSM_TCSR_BASE	      IOMEM(0xE000A000)
-#define MSM_TCSR_PHYS	      0xAB600000
-#define MSM_TCSR_SIZE	      SZ_4K
-
-#define MSM_SHARED_RAM_BASE   IOMEM(0xE0100000)
-#define MSM_SHARED_RAM_PHYS   0x00100000
-#define MSM_SHARED_RAM_SIZE   SZ_1M
-
-#define MSM_UART1_PHYS        0xACA00000
-#define MSM_UART1_SIZE        SZ_4K
-
-#define MSM_UART2_PHYS        0xACB00000
-#define MSM_UART2_SIZE        SZ_4K
-
-#define MSM_UART3_PHYS        0xACC00000
-#define MSM_UART3_SIZE        SZ_4K
-
-#define MSM_MDC_BASE	      IOMEM(0xE0200000)
-#define MSM_MDC_PHYS	      0xAA500000
-#define MSM_MDC_SIZE	      SZ_1M
-
-#define MSM_AD5_BASE          IOMEM(0xE0300000)
-#define MSM_AD5_PHYS          0xA7000000
-#define MSM_AD5_SIZE          (SZ_1M*13)
-
-#define MSM_HSUSB_PHYS        0xA3600000
-#define MSM_HSUSB_SIZE        SZ_1K
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h b/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h
deleted file mode 100644
index 0faa894..0000000
--- a/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h
+++ /dev/null
@@ -1,125 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2008-2011 Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- *
- * The MSM peripherals are spread all over across 768MB of physical
- * space, which makes just having a simple IO_ADDRESS macro to slide
- * them into the right virtual location rough.  Instead, we will
- * provide a master phys->virt mapping for peripherals here.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IOMAP_8X50_H
-#define __ASM_ARCH_MSM_IOMAP_8X50_H
-
-/* Physical base address and size of peripherals.
- * Ordered by the virtual base addresses they will be mapped at.
- *
- * MSM_VIC_BASE must be an value that can be loaded via a "mov"
- * instruction, otherwise entry-macro.S will not compile.
- *
- * If you add or remove entries here, you'll want to edit the
- * msm_io_desc array in arch/arm/mach-msm/io.c to reflect your
- * changes.
- *
- */
-
-#define MSM_VIC_BASE          IOMEM(0xE0000000)
-#define MSM_VIC_PHYS          0xAC000000
-#define MSM_VIC_SIZE          SZ_4K
-
-#define QSD8X50_CSR_PHYS      0xAC100000
-#define QSD8X50_CSR_SIZE      SZ_4K
-
-#define MSM_DMOV_BASE         IOMEM(0xE0002000)
-#define MSM_DMOV_PHYS         0xA9700000
-#define MSM_DMOV_SIZE         SZ_4K
-
-#define QSD8X50_GPIO1_PHYS        0xA9000000
-#define QSD8X50_GPIO1_SIZE        SZ_4K
-
-#define QSD8X50_GPIO2_PHYS        0xA9100000
-#define QSD8X50_GPIO2_SIZE        SZ_4K
-
-#define MSM_CLK_CTL_BASE      IOMEM(0xE0005000)
-#define MSM_CLK_CTL_PHYS      0xA8600000
-#define MSM_CLK_CTL_SIZE      SZ_4K
-
-#define MSM_SIRC_BASE         IOMEM(0xE1006000)
-#define MSM_SIRC_PHYS         0xAC200000
-#define MSM_SIRC_SIZE         SZ_4K
-
-#define MSM_SCPLL_BASE        IOMEM(0xE1007000)
-#define MSM_SCPLL_PHYS        0xA8800000
-#define MSM_SCPLL_SIZE        SZ_4K
-
-#ifdef CONFIG_MSM_SOC_REV_A
-#define MSM_SMI_BASE 0xE0000000
-#else
-#define MSM_SMI_BASE 0x00000000
-#endif
-
-#define MSM_SHARED_RAM_BASE   IOMEM(0xE0100000)
-#define MSM_SHARED_RAM_PHYS (MSM_SMI_BASE + 0x00100000)
-#define MSM_SHARED_RAM_SIZE   SZ_1M
-
-#define MSM_UART1_PHYS        0xA9A00000
-#define MSM_UART1_SIZE        SZ_4K
-
-#define MSM_UART2_PHYS        0xA9B00000
-#define MSM_UART2_SIZE        SZ_4K
-
-#define MSM_UART3_PHYS        0xA9C00000
-#define MSM_UART3_SIZE        SZ_4K
-
-#define MSM_MDC_BASE	      IOMEM(0xE0200000)
-#define MSM_MDC_PHYS	      0xAA500000
-#define MSM_MDC_SIZE	      SZ_1M
-
-#define MSM_AD5_BASE          IOMEM(0xE0300000)
-#define MSM_AD5_PHYS          0xAC000000
-#define MSM_AD5_SIZE          (SZ_1M*13)
-
-
-#define MSM_I2C_SIZE          SZ_4K
-#define MSM_I2C_PHYS          0xA9900000
-
-#define MSM_HSUSB_PHYS        0xA0800000
-#define MSM_HSUSB_SIZE        SZ_1K
-
-#define MSM_NAND_PHYS           0xA0A00000
-
-
-#define MSM_TSIF_PHYS        (0xa0100000)
-#define MSM_TSIF_SIZE        (0x200)
-
-#define MSM_TSSC_PHYS         0xAA300000
-
-#define MSM_UART1DM_PHYS      0xA0200000
-#define MSM_UART2DM_PHYS      0xA0900000
-
-
-#define MSM_SDC1_PHYS          0xA0300000
-#define MSM_SDC1_SIZE          SZ_4K
-
-#define MSM_SDC2_PHYS          0xA0400000
-#define MSM_SDC2_SIZE          SZ_4K
-
-#define MSM_SDC3_PHYS          0xA0500000
-#define MSM_SDC3_SIZE           SZ_4K
-
-#define MSM_SDC4_PHYS          0xA0600000
-#define MSM_SDC4_SIZE          SZ_4K
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h
deleted file mode 100644
index 0e4f491..0000000
--- a/arch/arm/mach-msm/include/mach/msm_iomap.h
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- *
- * The MSM peripherals are spread all over across 768MB of physical
- * space, which makes just having a simple IO_ADDRESS macro to slide
- * them into the right virtual location rough.  Instead, we will
- * provide a master phys->virt mapping for peripherals here.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_IOMAP_H
-#define __ASM_ARCH_MSM_IOMAP_H
-
-#include <asm/sizes.h>
-
-/* Physical base address and size of peripherals.
- * Ordered by the virtual base addresses they will be mapped at.
- *
- * MSM_VIC_BASE must be an value that can be loaded via a "mov"
- * instruction, otherwise entry-macro.S will not compile.
- *
- * If you add or remove entries here, you'll want to edit the
- * msm_io_desc array in arch/arm/mach-msm/io.c to reflect your
- * changes.
- *
- */
-
-#if defined(CONFIG_ARCH_MSM7X30)
-#include "msm_iomap-7x30.h"
-#elif defined(CONFIG_ARCH_QSD8X50)
-#include "msm_iomap-8x50.h"
-#else
-#include "msm_iomap-7x00.h"
-#endif
-
-/* Virtual addresses shared across all MSM targets. */
-#define MSM_CSR_BASE		IOMEM(0xE0001000)
-#define MSM_GPIO1_BASE		IOMEM(0xE0003000)
-#define MSM_GPIO2_BASE		IOMEM(0xE0004000)
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/msm_smd.h b/arch/arm/mach-msm/include/mach/msm_smd.h
deleted file mode 100644
index 029463e..0000000
--- a/arch/arm/mach-msm/include/mach/msm_smd.h
+++ /dev/null
@@ -1,109 +0,0 @@
-/* linux/include/asm-arm/arch-msm/msm_smd.h
- *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ASM_ARCH_MSM_SMD_H
-#define __ASM_ARCH_MSM_SMD_H
-
-typedef struct smd_channel smd_channel_t;
-
-extern int (*msm_check_for_modem_crash)(void);
-
-/* warning: notify() may be called before open returns */
-int smd_open(const char *name, smd_channel_t **ch, void *priv,
-	     void (*notify)(void *priv, unsigned event));
-
-#define SMD_EVENT_DATA 1
-#define SMD_EVENT_OPEN 2
-#define SMD_EVENT_CLOSE 3
-
-int smd_close(smd_channel_t *ch);
-
-/* passing a null pointer for data reads and discards */
-int smd_read(smd_channel_t *ch, void *data, int len);
-
-/* Write to stream channels may do a partial write and return
-** the length actually written.
-** Write to packet channels will never do a partial write --
-** it will return the requested length written or an error.
-*/
-int smd_write(smd_channel_t *ch, const void *data, int len);
-int smd_write_atomic(smd_channel_t *ch, const void *data, int len);
-
-int smd_write_avail(smd_channel_t *ch);
-int smd_read_avail(smd_channel_t *ch);
-
-/* Returns the total size of the current packet being read.
-** Returns 0 if no packets available or a stream channel.
-*/
-int smd_cur_packet_size(smd_channel_t *ch);
-
-/* used for tty unthrottling and the like -- causes the notify()
-** callback to be called from the same lock context as is used
-** when it is called from channel updates
-*/
-void smd_kick(smd_channel_t *ch);
-
-
-#if 0
-/* these are interruptable waits which will block you until the specified
-** number of bytes are readable or writable.
-*/
-int smd_wait_until_readable(smd_channel_t *ch, int bytes);
-int smd_wait_until_writable(smd_channel_t *ch, int bytes);
-#endif
-
-typedef enum {
-	SMD_PORT_DS = 0,
-	SMD_PORT_DIAG,
-	SMD_PORT_RPC_CALL,
-	SMD_PORT_RPC_REPLY,
-	SMD_PORT_BT,
-	SMD_PORT_CONTROL,
-	SMD_PORT_MEMCPY_SPARE1,
-	SMD_PORT_DATA1,
-	SMD_PORT_DATA2,
-	SMD_PORT_DATA3,
-	SMD_PORT_DATA4,
-	SMD_PORT_DATA5,
-	SMD_PORT_DATA6,
-	SMD_PORT_DATA7,
-	SMD_PORT_DATA8,
-	SMD_PORT_DATA9,
-	SMD_PORT_DATA10,
-	SMD_PORT_DATA11,
-	SMD_PORT_DATA12,
-	SMD_PORT_DATA13,
-	SMD_PORT_DATA14,
-	SMD_PORT_DATA15,
-	SMD_PORT_DATA16,
-	SMD_PORT_DATA17,
-	SMD_PORT_DATA18,
-	SMD_PORT_DATA19,
-	SMD_PORT_DATA20,
-	SMD_PORT_GPS_NMEA,
-	SMD_PORT_BRIDGE_1,
-	SMD_PORT_BRIDGE_2,
-	SMD_PORT_BRIDGE_3,
-	SMD_PORT_BRIDGE_4,
-	SMD_PORT_BRIDGE_5,
-	SMD_PORT_LOOPBACK,
-	SMD_PORT_CS_APPS_MODEM,
-	SMD_PORT_CS_APPS_DSP,
-	SMD_PORT_CS_MODEM_DSP,
-	SMD_NUM_PORTS,
-} smd_port_id_type;
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/sirc.h b/arch/arm/mach-msm/include/mach/sirc.h
deleted file mode 100644
index ef55868..0000000
--- a/arch/arm/mach-msm/include/mach/sirc.h
+++ /dev/null
@@ -1,98 +0,0 @@
-/* Copyright (c) 2008-2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#ifndef __ASM_ARCH_MSM_SIRC_H
-#define __ASM_ARCH_MSM_SIRC_H
-
-struct sirc_regs_t {
-	void    *int_enable;
-	void    *int_enable_clear;
-	void    *int_enable_set;
-	void    *int_type;
-	void    *int_polarity;
-	void    *int_clear;
-};
-
-struct sirc_cascade_regs {
-	void    *int_status;
-	unsigned int    cascade_irq;
-};
-
-void msm_init_sirc(void);
-void msm_sirc_enter_sleep(void);
-void msm_sirc_exit_sleep(void);
-
-#if defined(CONFIG_ARCH_MSM_SCORPION)
-
-#include <mach/msm_iomap.h>
-
-/*
- * Secondary interrupt controller interrupts
- */
-
-#define FIRST_SIRC_IRQ (NR_MSM_IRQS + NR_GPIO_IRQS)
-
-#define INT_UART1                     (FIRST_SIRC_IRQ + 0)
-#define INT_UART2                     (FIRST_SIRC_IRQ + 1)
-#define INT_UART3                     (FIRST_SIRC_IRQ + 2)
-#define INT_UART1_RX                  (FIRST_SIRC_IRQ + 3)
-#define INT_UART2_RX                  (FIRST_SIRC_IRQ + 4)
-#define INT_UART3_RX                  (FIRST_SIRC_IRQ + 5)
-#define INT_SPI_INPUT                 (FIRST_SIRC_IRQ + 6)
-#define INT_SPI_OUTPUT                (FIRST_SIRC_IRQ + 7)
-#define INT_SPI_ERROR                 (FIRST_SIRC_IRQ + 8)
-#define INT_GPIO_GROUP1               (FIRST_SIRC_IRQ + 9)
-#define INT_GPIO_GROUP2               (FIRST_SIRC_IRQ + 10)
-#define INT_GPIO_GROUP1_SECURE        (FIRST_SIRC_IRQ + 11)
-#define INT_GPIO_GROUP2_SECURE        (FIRST_SIRC_IRQ + 12)
-#define INT_AVS_SVIC                  (FIRST_SIRC_IRQ + 13)
-#define INT_AVS_REQ_UP                (FIRST_SIRC_IRQ + 14)
-#define INT_AVS_REQ_DOWN              (FIRST_SIRC_IRQ + 15)
-#define INT_PBUS_ERR                  (FIRST_SIRC_IRQ + 16)
-#define INT_AXI_ERR                   (FIRST_SIRC_IRQ + 17)
-#define INT_SMI_ERR                   (FIRST_SIRC_IRQ + 18)
-#define INT_EBI1_ERR                  (FIRST_SIRC_IRQ + 19)
-#define INT_IMEM_ERR                  (FIRST_SIRC_IRQ + 20)
-#define INT_TEMP_SENSOR               (FIRST_SIRC_IRQ + 21)
-#define INT_TV_ENC                    (FIRST_SIRC_IRQ + 22)
-#define INT_GRP2D                     (FIRST_SIRC_IRQ + 23)
-#define INT_GSBI_QUP                  (FIRST_SIRC_IRQ + 24)
-#define INT_SC_ACG                    (FIRST_SIRC_IRQ + 25)
-#define INT_WDT0                      (FIRST_SIRC_IRQ + 26)
-#define INT_WDT1                      (FIRST_SIRC_IRQ + 27)
-
-#if defined(CONFIG_MSM_SOC_REV_A)
-#define NR_SIRC_IRQS                  28
-#define SIRC_MASK                     0x0FFFFFFF
-#else
-#define NR_SIRC_IRQS                  23
-#define SIRC_MASK                     0x007FFFFF
-#endif
-
-#define LAST_SIRC_IRQ                 (FIRST_SIRC_IRQ + NR_SIRC_IRQS - 1)
-
-#define SPSS_SIRC_INT_SELECT          (MSM_SIRC_BASE + 0x00)
-#define SPSS_SIRC_INT_ENABLE          (MSM_SIRC_BASE + 0x04)
-#define SPSS_SIRC_INT_ENABLE_CLEAR    (MSM_SIRC_BASE + 0x08)
-#define SPSS_SIRC_INT_ENABLE_SET      (MSM_SIRC_BASE + 0x0C)
-#define SPSS_SIRC_INT_TYPE            (MSM_SIRC_BASE + 0x10)
-#define SPSS_SIRC_INT_POLARITY        (MSM_SIRC_BASE + 0x14)
-#define SPSS_SIRC_SECURITY            (MSM_SIRC_BASE + 0x18)
-#define SPSS_SIRC_IRQ_STATUS          (MSM_SIRC_BASE + 0x1C)
-#define SPSS_SIRC_IRQ1_STATUS         (MSM_SIRC_BASE + 0x20)
-#define SPSS_SIRC_RAW_STATUS          (MSM_SIRC_BASE + 0x24)
-#define SPSS_SIRC_INT_CLEAR           (MSM_SIRC_BASE + 0x28)
-#define SPSS_SIRC_SOFT_INT            (MSM_SIRC_BASE + 0x2C)
-
-#endif
-
-#endif
diff --git a/arch/arm/mach-msm/include/mach/vreg.h b/arch/arm/mach-msm/include/mach/vreg.h
deleted file mode 100644
index 6626e78..0000000
--- a/arch/arm/mach-msm/include/mach/vreg.h
+++ /dev/null
@@ -1,29 +0,0 @@
-/* linux/include/asm-arm/arch-msm/vreg.h
- *
- * Copyright (C) 2008 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef __ARCH_ARM_MACH_MSM_VREG_H
-#define __ARCH_ARM_MACH_MSM_VREG_H
-
-struct vreg;
-
-struct vreg *vreg_get(struct device *dev, const char *id);
-void vreg_put(struct vreg *vreg);
-
-int vreg_enable(struct vreg *vreg);
-int vreg_disable(struct vreg *vreg);
-int vreg_set_level(struct vreg *vreg, unsigned mv);
-
-#endif
diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
deleted file mode 100644
index b042dca..0000000
--- a/arch/arm/mach-msm/io.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/* arch/arm/mach-msm/io.c
- *
- * MSM7K, QSD io support
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/bug.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/export.h>
-
-#include <mach/hardware.h>
-#include <asm/page.h>
-#include <mach/msm_iomap.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-
-#define MSM_CHIP_DEVICE_TYPE(name, chip, mem_type) {			      \
-		.virtual = (unsigned long) MSM_##name##_BASE, \
-		.pfn = __phys_to_pfn(chip##_##name##_PHYS), \
-		.length = chip##_##name##_SIZE, \
-		.type = mem_type, \
-	 }
-
-#define MSM_DEVICE_TYPE(name, mem_type) \
-		MSM_CHIP_DEVICE_TYPE(name, MSM, mem_type)
-#define MSM_CHIP_DEVICE(name, chip) \
-		MSM_CHIP_DEVICE_TYPE(name, chip, MT_DEVICE)
-#define MSM_DEVICE(name) MSM_CHIP_DEVICE(name, MSM)
-
-#if defined(CONFIG_ARCH_MSM7X00A)
-static struct map_desc msm_io_desc[] __initdata = {
-	MSM_DEVICE_TYPE(VIC, MT_DEVICE_NONSHARED),
-	MSM_CHIP_DEVICE_TYPE(CSR, MSM7X00, MT_DEVICE_NONSHARED),
-	MSM_DEVICE_TYPE(DMOV, MT_DEVICE_NONSHARED),
-	MSM_CHIP_DEVICE_TYPE(GPIO1, MSM7X00, MT_DEVICE_NONSHARED),
-	MSM_CHIP_DEVICE_TYPE(GPIO2, MSM7X00, MT_DEVICE_NONSHARED),
-	MSM_DEVICE_TYPE(CLK_CTL, MT_DEVICE_NONSHARED),
-	{
-		.virtual =  (unsigned long) MSM_SHARED_RAM_BASE,
-		.pfn = __phys_to_pfn(MSM_SHARED_RAM_PHYS),
-		.length =   MSM_SHARED_RAM_SIZE,
-		.type =     MT_DEVICE,
-	},
-#if defined(CONFIG_DEBUG_MSM_UART)
-	{
-		/* Must be last: virtual and pfn filled in by debug_ll_addr() */
-		.length = SZ_4K,
-		.type = MT_DEVICE_NONSHARED,
-	}
-#endif
-};
-
-void __init msm_map_common_io(void)
-{
-	size_t size = ARRAY_SIZE(msm_io_desc);
-
-	/* Make sure the peripheral register window is closed, since
-	 * we will use PTE flags (TEX[1]=1,B=0,C=1) to determine which
-	 * pages are peripheral interface or not.
-	 */
-	asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
-#if defined(CONFIG_DEBUG_MSM_UART)
-#ifdef CONFIG_MMU
-	debug_ll_addr(&msm_io_desc[size - 1].pfn,
-		      &msm_io_desc[size - 1].virtual);
-#endif
-	msm_io_desc[size - 1].pfn = __phys_to_pfn(msm_io_desc[size - 1].pfn);
-#endif
-	iotable_init(msm_io_desc, size);
-}
-#endif
-
-#ifdef CONFIG_ARCH_QSD8X50
-static struct map_desc qsd8x50_io_desc[] __initdata = {
-	MSM_DEVICE(VIC),
-	MSM_CHIP_DEVICE(CSR, QSD8X50),
-	MSM_DEVICE(DMOV),
-	MSM_CHIP_DEVICE(GPIO1, QSD8X50),
-	MSM_CHIP_DEVICE(GPIO2, QSD8X50),
-	MSM_DEVICE(CLK_CTL),
-	MSM_DEVICE(SIRC),
-	MSM_DEVICE(SCPLL),
-	MSM_DEVICE(AD5),
-	MSM_DEVICE(MDC),
-	{
-		.virtual =  (unsigned long) MSM_SHARED_RAM_BASE,
-		.pfn = __phys_to_pfn(MSM_SHARED_RAM_PHYS),
-		.length =   MSM_SHARED_RAM_SIZE,
-		.type =     MT_DEVICE,
-	},
-};
-
-void __init msm_map_qsd8x50_io(void)
-{
-	debug_ll_io_init();
-	iotable_init(qsd8x50_io_desc, ARRAY_SIZE(qsd8x50_io_desc));
-}
-#endif /* CONFIG_ARCH_QSD8X50 */
-
-#ifdef CONFIG_ARCH_MSM7X30
-static struct map_desc msm7x30_io_desc[] __initdata = {
-	MSM_DEVICE(VIC),
-	MSM_CHIP_DEVICE(CSR, MSM7X30),
-	MSM_DEVICE(DMOV),
-	MSM_CHIP_DEVICE(GPIO1, MSM7X30),
-	MSM_CHIP_DEVICE(GPIO2, MSM7X30),
-	MSM_DEVICE(CLK_CTL),
-	MSM_DEVICE(CLK_CTL_SH2),
-	MSM_DEVICE(AD5),
-	MSM_DEVICE(MDC),
-	MSM_DEVICE(ACC),
-	MSM_DEVICE(SAW),
-	MSM_DEVICE(GCC),
-	MSM_DEVICE(TCSR),
-	{
-		.virtual =  (unsigned long) MSM_SHARED_RAM_BASE,
-		.pfn = __phys_to_pfn(MSM_SHARED_RAM_PHYS),
-		.length =   MSM_SHARED_RAM_SIZE,
-		.type =     MT_DEVICE,
-	},
-};
-
-void __init msm_map_msm7x30_io(void)
-{
-	debug_ll_io_init();
-	iotable_init(msm7x30_io_desc, ARRAY_SIZE(msm7x30_io_desc));
-}
-#endif /* CONFIG_ARCH_MSM7X30 */
-
-#ifdef CONFIG_ARCH_MSM7X00A
-void __iomem *__msm_ioremap_caller(phys_addr_t phys_addr, size_t size,
-				   unsigned int mtype, void *caller)
-{
-	if (mtype == MT_DEVICE) {
-		/* The peripherals in the 88000000 - D0000000 range
-		 * are only accessible by type MT_DEVICE_NONSHARED.
-		 * Adjust mtype as necessary to make this "just work."
-		 */
-		if ((phys_addr >= 0x88000000) && (phys_addr < 0xD0000000))
-			mtype = MT_DEVICE_NONSHARED;
-	}
-
-	return __arm_ioremap_caller(phys_addr, size, mtype, caller);
-}
-#endif
diff --git a/arch/arm/mach-msm/irq-vic.c b/arch/arm/mach-msm/irq-vic.c
deleted file mode 100644
index 1b54f80..0000000
--- a/arch/arm/mach-msm/irq-vic.c
+++ /dev/null
@@ -1,363 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-#include <linux/timer.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-
-#include <asm/cacheflush.h>
-
-#include <mach/hardware.h>
-
-#include <mach/msm_iomap.h>
-
-#include "smd_private.h"
-
-enum {
-	IRQ_DEBUG_SLEEP_INT_TRIGGER = 1U << 0,
-	IRQ_DEBUG_SLEEP_INT = 1U << 1,
-	IRQ_DEBUG_SLEEP_ABORT = 1U << 2,
-	IRQ_DEBUG_SLEEP = 1U << 3,
-	IRQ_DEBUG_SLEEP_REQUEST = 1U << 4,
-};
-static int msm_irq_debug_mask;
-module_param_named(debug_mask, msm_irq_debug_mask, int,
-		   S_IRUGO | S_IWUSR | S_IWGRP);
-
-#define VIC_REG(off) (MSM_VIC_BASE + (off))
-#define VIC_INT_TO_REG_ADDR(base, irq) (base + (irq / 32) * 4)
-#define VIC_INT_TO_REG_INDEX(irq) ((irq >> 5) & 3)
-
-#define VIC_INT_SELECT0     VIC_REG(0x0000)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_SELECT1     VIC_REG(0x0004)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_SELECT2     VIC_REG(0x0008)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_SELECT3     VIC_REG(0x000C)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_EN0         VIC_REG(0x0010)
-#define VIC_INT_EN1         VIC_REG(0x0014)
-#define VIC_INT_EN2         VIC_REG(0x0018)
-#define VIC_INT_EN3         VIC_REG(0x001C)
-#define VIC_INT_ENCLEAR0    VIC_REG(0x0020)
-#define VIC_INT_ENCLEAR1    VIC_REG(0x0024)
-#define VIC_INT_ENCLEAR2    VIC_REG(0x0028)
-#define VIC_INT_ENCLEAR3    VIC_REG(0x002C)
-#define VIC_INT_ENSET0      VIC_REG(0x0030)
-#define VIC_INT_ENSET1      VIC_REG(0x0034)
-#define VIC_INT_ENSET2      VIC_REG(0x0038)
-#define VIC_INT_ENSET3      VIC_REG(0x003C)
-#define VIC_INT_TYPE0       VIC_REG(0x0040)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_TYPE1       VIC_REG(0x0044)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_TYPE2       VIC_REG(0x0048)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_TYPE3       VIC_REG(0x004C)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_POLARITY0   VIC_REG(0x0050)  /* 1: NEG, 0: POS */
-#define VIC_INT_POLARITY1   VIC_REG(0x0054)  /* 1: NEG, 0: POS */
-#define VIC_INT_POLARITY2   VIC_REG(0x0058)  /* 1: NEG, 0: POS */
-#define VIC_INT_POLARITY3   VIC_REG(0x005C)  /* 1: NEG, 0: POS */
-#define VIC_NO_PEND_VAL     VIC_REG(0x0060)
-
-#if defined(CONFIG_ARCH_MSM_SCORPION)
-#define VIC_NO_PEND_VAL_FIQ VIC_REG(0x0064)
-#define VIC_INT_MASTEREN    VIC_REG(0x0068)  /* 1: IRQ, 2: FIQ     */
-#define VIC_CONFIG          VIC_REG(0x006C)  /* 1: USE SC VIC */
-#else
-#define VIC_INT_MASTEREN    VIC_REG(0x0064)  /* 1: IRQ, 2: FIQ     */
-#define VIC_PROTECTION      VIC_REG(0x006C)  /* 1: ENABLE          */
-#define VIC_CONFIG          VIC_REG(0x0068)  /* 1: USE ARM1136 VIC */
-#endif
-
-#define VIC_IRQ_STATUS0     VIC_REG(0x0080)
-#define VIC_IRQ_STATUS1     VIC_REG(0x0084)
-#define VIC_IRQ_STATUS2     VIC_REG(0x0088)
-#define VIC_IRQ_STATUS3     VIC_REG(0x008C)
-#define VIC_FIQ_STATUS0     VIC_REG(0x0090)
-#define VIC_FIQ_STATUS1     VIC_REG(0x0094)
-#define VIC_FIQ_STATUS2     VIC_REG(0x0098)
-#define VIC_FIQ_STATUS3     VIC_REG(0x009C)
-#define VIC_RAW_STATUS0     VIC_REG(0x00A0)
-#define VIC_RAW_STATUS1     VIC_REG(0x00A4)
-#define VIC_RAW_STATUS2     VIC_REG(0x00A8)
-#define VIC_RAW_STATUS3     VIC_REG(0x00AC)
-#define VIC_INT_CLEAR0      VIC_REG(0x00B0)
-#define VIC_INT_CLEAR1      VIC_REG(0x00B4)
-#define VIC_INT_CLEAR2      VIC_REG(0x00B8)
-#define VIC_INT_CLEAR3      VIC_REG(0x00BC)
-#define VIC_SOFTINT0        VIC_REG(0x00C0)
-#define VIC_SOFTINT1        VIC_REG(0x00C4)
-#define VIC_SOFTINT2        VIC_REG(0x00C8)
-#define VIC_SOFTINT3        VIC_REG(0x00CC)
-#define VIC_IRQ_VEC_RD      VIC_REG(0x00D0)  /* pending int # */
-#define VIC_IRQ_VEC_PEND_RD VIC_REG(0x00D4)  /* pending vector addr */
-#define VIC_IRQ_VEC_WR      VIC_REG(0x00D8)
-
-#if defined(CONFIG_ARCH_MSM_SCORPION)
-#define VIC_FIQ_VEC_RD      VIC_REG(0x00DC)
-#define VIC_FIQ_VEC_PEND_RD VIC_REG(0x00E0)
-#define VIC_FIQ_VEC_WR      VIC_REG(0x00E4)
-#define VIC_IRQ_IN_SERVICE  VIC_REG(0x00E8)
-#define VIC_IRQ_IN_STACK    VIC_REG(0x00EC)
-#define VIC_FIQ_IN_SERVICE  VIC_REG(0x00F0)
-#define VIC_FIQ_IN_STACK    VIC_REG(0x00F4)
-#define VIC_TEST_BUS_SEL    VIC_REG(0x00F8)
-#define VIC_IRQ_CTRL_CONFIG VIC_REG(0x00FC)
-#else
-#define VIC_IRQ_IN_SERVICE  VIC_REG(0x00E0)
-#define VIC_IRQ_IN_STACK    VIC_REG(0x00E4)
-#define VIC_TEST_BUS_SEL    VIC_REG(0x00E8)
-#endif
-
-#define VIC_VECTPRIORITY(n) VIC_REG(0x0200+((n) * 4))
-#define VIC_VECTADDR(n)     VIC_REG(0x0400+((n) * 4))
-
-#if defined(CONFIG_ARCH_MSM7X30)
-#define VIC_NUM_REGS	    4
-#else
-#define VIC_NUM_REGS	    2
-#endif
-
-#if VIC_NUM_REGS == 2
-#define DPRINT_REGS(base_reg, format, ...)	      			\
-	printk(KERN_INFO format " %x %x\n", ##__VA_ARGS__,		\
-			readl(base_reg ## 0), readl(base_reg ## 1))
-#define DPRINT_ARRAY(array, format, ...)				\
-	printk(KERN_INFO format " %x %x\n", ##__VA_ARGS__,		\
-			array[0], array[1])
-#elif VIC_NUM_REGS == 4
-#define DPRINT_REGS(base_reg, format, ...) \
-	printk(KERN_INFO format " %x %x %x %x\n", ##__VA_ARGS__,	\
-			readl(base_reg ## 0), readl(base_reg ## 1),	\
-			readl(base_reg ## 2), readl(base_reg ## 3))
-#define DPRINT_ARRAY(array, format, ...)				\
-	printk(KERN_INFO format " %x %x %x %x\n", ##__VA_ARGS__,	\
-			array[0], array[1],				\
-			array[2], array[3])
-#else
-#error "VIC_NUM_REGS set to illegal value"
-#endif
-
-static uint32_t msm_irq_smsm_wake_enable[2];
-static struct {
-	uint32_t int_en[2];
-	uint32_t int_type;
-	uint32_t int_polarity;
-	uint32_t int_select;
-} msm_irq_shadow_reg[VIC_NUM_REGS];
-static uint32_t msm_irq_idle_disable[VIC_NUM_REGS];
-
-#define SMSM_FAKE_IRQ (0xff)
-static uint8_t msm_irq_to_smsm[NR_IRQS] = {
-	[INT_MDDI_EXT] = 1,
-	[INT_MDDI_PRI] = 2,
-	[INT_MDDI_CLIENT] = 3,
-	[INT_USB_OTG] = 4,
-
-	[INT_PWB_I2C] = 5,
-	[INT_SDC1_0] = 6,
-	[INT_SDC1_1] = 7,
-	[INT_SDC2_0] = 8,
-
-	[INT_SDC2_1] = 9,
-	[INT_ADSP_A9_A11] = 10,
-	[INT_UART1] = 11,
-	[INT_UART2] = 12,
-
-	[INT_UART3] = 13,
-	[INT_UART1_RX] = 14,
-	[INT_UART2_RX] = 15,
-	[INT_UART3_RX] = 16,
-
-	[INT_UART1DM_IRQ] = 17,
-	[INT_UART1DM_RX] = 18,
-	[INT_KEYSENSE] = 19,
-#if !defined(CONFIG_ARCH_MSM7X30)
-	[INT_AD_HSSD] = 20,
-#endif
-
-	[INT_NAND_WR_ER_DONE] = 21,
-	[INT_NAND_OP_DONE] = 22,
-	[INT_TCHSCRN1] = 23,
-	[INT_TCHSCRN2] = 24,
-
-	[INT_TCHSCRN_SSBI] = 25,
-	[INT_USB_HS] = 26,
-	[INT_UART2DM_RX] = 27,
-	[INT_UART2DM_IRQ] = 28,
-
-	[INT_SDC4_1] = 29,
-	[INT_SDC4_0] = 30,
-	[INT_SDC3_1] = 31,
-	[INT_SDC3_0] = 32,
-
-	/* fake wakeup interrupts */
-	[INT_GPIO_GROUP1] = SMSM_FAKE_IRQ,
-	[INT_GPIO_GROUP2] = SMSM_FAKE_IRQ,
-	[INT_A9_M2A_0] = SMSM_FAKE_IRQ,
-	[INT_A9_M2A_1] = SMSM_FAKE_IRQ,
-	[INT_A9_M2A_5] = SMSM_FAKE_IRQ,
-	[INT_GP_TIMER_EXP] = SMSM_FAKE_IRQ,
-	[INT_DEBUG_TIMER_EXP] = SMSM_FAKE_IRQ,
-	[INT_ADSP_A11] = SMSM_FAKE_IRQ,
-#ifdef CONFIG_ARCH_QSD8X50
-	[INT_SIRC_0] = SMSM_FAKE_IRQ,
-	[INT_SIRC_1] = SMSM_FAKE_IRQ,
-#endif
-};
-
-static inline void msm_irq_write_all_regs(void __iomem *base, unsigned int val)
-{
-	int i;
-
-	for (i = 0; i < VIC_NUM_REGS; i++)
-		writel(val, base + (i * 4));
-}
-
-static void msm_irq_ack(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_TO_REG_ADDR(VIC_INT_CLEAR0, d->irq);
-	writel(1 << (d->irq & 31), reg);
-}
-
-static void msm_irq_mask(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_TO_REG_ADDR(VIC_INT_ENCLEAR0, d->irq);
-	unsigned index = VIC_INT_TO_REG_INDEX(d->irq);
-	uint32_t mask = 1UL << (d->irq & 31);
-	int smsm_irq = msm_irq_to_smsm[d->irq];
-
-	msm_irq_shadow_reg[index].int_en[0] &= ~mask;
-	writel(mask, reg);
-	if (smsm_irq == 0)
-		msm_irq_idle_disable[index] &= ~mask;
-	else {
-		mask = 1UL << (smsm_irq - 1);
-		msm_irq_smsm_wake_enable[0] &= ~mask;
-	}
-}
-
-static void msm_irq_unmask(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_TO_REG_ADDR(VIC_INT_ENSET0, d->irq);
-	unsigned index = VIC_INT_TO_REG_INDEX(d->irq);
-	uint32_t mask = 1UL << (d->irq & 31);
-	int smsm_irq = msm_irq_to_smsm[d->irq];
-
-	msm_irq_shadow_reg[index].int_en[0] |= mask;
-	writel(mask, reg);
-
-	if (smsm_irq == 0)
-		msm_irq_idle_disable[index] |= mask;
-	else {
-		mask = 1UL << (smsm_irq - 1);
-		msm_irq_smsm_wake_enable[0] |= mask;
-	}
-}
-
-static int msm_irq_set_wake(struct irq_data *d, unsigned int on)
-{
-	unsigned index = VIC_INT_TO_REG_INDEX(d->irq);
-	uint32_t mask = 1UL << (d->irq & 31);
-	int smsm_irq = msm_irq_to_smsm[d->irq];
-
-	if (smsm_irq == 0) {
-		printk(KERN_ERR "msm_irq_set_wake: bad wakeup irq %d\n", d->irq);
-		return -EINVAL;
-	}
-	if (on)
-		msm_irq_shadow_reg[index].int_en[1] |= mask;
-	else
-		msm_irq_shadow_reg[index].int_en[1] &= ~mask;
-
-	if (smsm_irq == SMSM_FAKE_IRQ)
-		return 0;
-
-	mask = 1UL << (smsm_irq - 1);
-	if (on)
-		msm_irq_smsm_wake_enable[1] |= mask;
-	else
-		msm_irq_smsm_wake_enable[1] &= ~mask;
-	return 0;
-}
-
-static int msm_irq_set_type(struct irq_data *d, unsigned int flow_type)
-{
-	void __iomem *treg = VIC_INT_TO_REG_ADDR(VIC_INT_TYPE0, d->irq);
-	void __iomem *preg = VIC_INT_TO_REG_ADDR(VIC_INT_POLARITY0, d->irq);
-	unsigned index = VIC_INT_TO_REG_INDEX(d->irq);
-	int b = 1 << (d->irq & 31);
-	uint32_t polarity;
-	uint32_t type;
-
-	polarity = msm_irq_shadow_reg[index].int_polarity;
-	if (flow_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
-		polarity |= b;
-	if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_HIGH))
-		polarity &= ~b;
-	writel(polarity, preg);
-	msm_irq_shadow_reg[index].int_polarity = polarity;
-
-	type = msm_irq_shadow_reg[index].int_type;
-	if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
-		type |= b;
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
-	}
-	if (flow_type & (IRQF_TRIGGER_HIGH | IRQF_TRIGGER_LOW)) {
-		type &= ~b;
-		__irq_set_handler_locked(d->irq, handle_level_irq);
-	}
-	writel(type, treg);
-	msm_irq_shadow_reg[index].int_type = type;
-	return 0;
-}
-
-static struct irq_chip msm_irq_chip = {
-	.name          = "msm",
-	.irq_disable   = msm_irq_mask,
-	.irq_ack       = msm_irq_ack,
-	.irq_mask      = msm_irq_mask,
-	.irq_unmask    = msm_irq_unmask,
-	.irq_set_wake  = msm_irq_set_wake,
-	.irq_set_type  = msm_irq_set_type,
-};
-
-void __init msm_init_irq(void)
-{
-	unsigned n;
-
-	/* select level interrupts */
-	msm_irq_write_all_regs(VIC_INT_TYPE0, 0);
-
-	/* select highlevel interrupts */
-	msm_irq_write_all_regs(VIC_INT_POLARITY0, 0);
-
-	/* select IRQ for all INTs */
-	msm_irq_write_all_regs(VIC_INT_SELECT0, 0);
-
-	/* disable all INTs */
-	msm_irq_write_all_regs(VIC_INT_EN0, 0);
-
-	/* don't use vic */
-	writel(0, VIC_CONFIG);
-
-	/* enable interrupt controller */
-	writel(3, VIC_INT_MASTEREN);
-
-	for (n = 0; n < NR_MSM_IRQS; n++) {
-		irq_set_chip_and_handler(n, &msm_irq_chip, handle_level_irq);
-		set_irq_flags(n, IRQF_VALID);
-	}
-}
diff --git a/arch/arm/mach-msm/irq.c b/arch/arm/mach-msm/irq.c
deleted file mode 100644
index ea514be..0000000
--- a/arch/arm/mach-msm/irq.c
+++ /dev/null
@@ -1,151 +0,0 @@
-/* linux/arch/arm/mach-msm/irq.c
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/sched.h>
-#include <linux/interrupt.h>
-#include <linux/ptrace.h>
-#include <linux/timer.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-
-#include <mach/msm_iomap.h>
-
-#define VIC_REG(off) (MSM_VIC_BASE + (off))
-
-#define VIC_INT_SELECT0     VIC_REG(0x0000)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_SELECT1     VIC_REG(0x0004)  /* 1: FIQ, 0: IRQ */
-#define VIC_INT_EN0         VIC_REG(0x0010)
-#define VIC_INT_EN1         VIC_REG(0x0014)
-#define VIC_INT_ENCLEAR0    VIC_REG(0x0020)
-#define VIC_INT_ENCLEAR1    VIC_REG(0x0024)
-#define VIC_INT_ENSET0      VIC_REG(0x0030)
-#define VIC_INT_ENSET1      VIC_REG(0x0034)
-#define VIC_INT_TYPE0       VIC_REG(0x0040)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_TYPE1       VIC_REG(0x0044)  /* 1: EDGE, 0: LEVEL  */
-#define VIC_INT_POLARITY0   VIC_REG(0x0050)  /* 1: NEG, 0: POS */
-#define VIC_INT_POLARITY1   VIC_REG(0x0054)  /* 1: NEG, 0: POS */
-#define VIC_NO_PEND_VAL     VIC_REG(0x0060)
-#define VIC_INT_MASTEREN    VIC_REG(0x0064)  /* 1: IRQ, 2: FIQ     */
-#define VIC_PROTECTION      VIC_REG(0x006C)  /* 1: ENABLE          */
-#define VIC_CONFIG          VIC_REG(0x0068)  /* 1: USE ARM1136 VIC */
-#define VIC_IRQ_STATUS0     VIC_REG(0x0080)
-#define VIC_IRQ_STATUS1     VIC_REG(0x0084)
-#define VIC_FIQ_STATUS0     VIC_REG(0x0090)
-#define VIC_FIQ_STATUS1     VIC_REG(0x0094)
-#define VIC_RAW_STATUS0     VIC_REG(0x00A0)
-#define VIC_RAW_STATUS1     VIC_REG(0x00A4)
-#define VIC_INT_CLEAR0      VIC_REG(0x00B0)
-#define VIC_INT_CLEAR1      VIC_REG(0x00B4)
-#define VIC_SOFTINT0        VIC_REG(0x00C0)
-#define VIC_SOFTINT1        VIC_REG(0x00C4)
-#define VIC_IRQ_VEC_RD      VIC_REG(0x00D0)  /* pending int # */
-#define VIC_IRQ_VEC_PEND_RD VIC_REG(0x00D4)  /* pending vector addr */
-#define VIC_IRQ_VEC_WR      VIC_REG(0x00D8)
-#define VIC_IRQ_IN_SERVICE  VIC_REG(0x00E0)
-#define VIC_IRQ_IN_STACK    VIC_REG(0x00E4)
-#define VIC_TEST_BUS_SEL    VIC_REG(0x00E8)
-
-#define VIC_VECTPRIORITY(n) VIC_REG(0x0200+((n) * 4))
-#define VIC_VECTADDR(n)     VIC_REG(0x0400+((n) * 4))
-
-static void msm_irq_ack(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_CLEAR0 + ((d->irq & 32) ? 4 : 0);
-	writel(1 << (d->irq & 31), reg);
-}
-
-static void msm_irq_mask(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_ENCLEAR0 + ((d->irq & 32) ? 4 : 0);
-	writel(1 << (d->irq & 31), reg);
-}
-
-static void msm_irq_unmask(struct irq_data *d)
-{
-	void __iomem *reg = VIC_INT_ENSET0 + ((d->irq & 32) ? 4 : 0);
-	writel(1 << (d->irq & 31), reg);
-}
-
-static int msm_irq_set_wake(struct irq_data *d, unsigned int on)
-{
-	return -EINVAL;
-}
-
-static int msm_irq_set_type(struct irq_data *d, unsigned int flow_type)
-{
-	void __iomem *treg = VIC_INT_TYPE0 + ((d->irq & 32) ? 4 : 0);
-	void __iomem *preg = VIC_INT_POLARITY0 + ((d->irq & 32) ? 4 : 0);
-	int b = 1 << (d->irq & 31);
-
-	if (flow_type & (IRQF_TRIGGER_FALLING | IRQF_TRIGGER_LOW))
-		writel(readl(preg) | b, preg);
-	if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_HIGH))
-		writel(readl(preg) & (~b), preg);
-
-	if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
-		writel(readl(treg) | b, treg);
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
-	}
-	if (flow_type & (IRQF_TRIGGER_HIGH | IRQF_TRIGGER_LOW)) {
-		writel(readl(treg) & (~b), treg);
-		__irq_set_handler_locked(d->irq, handle_level_irq);
-	}
-	return 0;
-}
-
-static struct irq_chip msm_irq_chip = {
-	.name          = "msm",
-	.irq_ack       = msm_irq_ack,
-	.irq_mask      = msm_irq_mask,
-	.irq_unmask    = msm_irq_unmask,
-	.irq_set_wake  = msm_irq_set_wake,
-	.irq_set_type  = msm_irq_set_type,
-};
-
-void __init msm_init_irq(void)
-{
-	unsigned n;
-
-	/* select level interrupts */
-	writel(0, VIC_INT_TYPE0);
-	writel(0, VIC_INT_TYPE1);
-
-	/* select highlevel interrupts */
-	writel(0, VIC_INT_POLARITY0);
-	writel(0, VIC_INT_POLARITY1);
-
-	/* select IRQ for all INTs */
-	writel(0, VIC_INT_SELECT0);
-	writel(0, VIC_INT_SELECT1);
-
-	/* disable all INTs */
-	writel(0, VIC_INT_EN0);
-	writel(0, VIC_INT_EN1);
-
-	/* don't use 1136 vic */
-	writel(0, VIC_CONFIG);
-
-	/* enable interrupt controller */
-	writel(1, VIC_INT_MASTEREN);
-
-	for (n = 0; n < NR_MSM_IRQS; n++) {
-		irq_set_chip_and_handler(n, &msm_irq_chip, handle_level_irq);
-		set_irq_flags(n, IRQF_VALID);
-	}
-}
diff --git a/arch/arm/mach-msm/last_radio_log.c b/arch/arm/mach-msm/last_radio_log.c
deleted file mode 100644
index 9c392a2..0000000
--- a/arch/arm/mach-msm/last_radio_log.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/* arch/arm/mach-msm/last_radio_log.c
- *
- * Extract the log from a modem crash though SMEM
- *
- * Copyright (C) 2007 Google, Inc.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/fs.h>
-#include <linux/proc_fs.h>
-#include <linux/uaccess.h>
-
-#include "smd_private.h"
-
-static void *radio_log_base;
-static size_t radio_log_size;
-
-extern void *smem_item(unsigned id, unsigned *size);
-
-static ssize_t last_radio_log_read(struct file *file, char __user *buf,
-			size_t len, loff_t *offset)
-{
-	return simple_read_from_buffer(buf, len, offset,
-				radio_log_base, radio_log_size);
-}
-
-static struct file_operations last_radio_log_fops = {
-	.read = last_radio_log_read,
-	.llseek = default_llseek,
-};
-
-void msm_init_last_radio_log(struct module *owner)
-{
-	struct proc_dir_entry *entry;
-
-	if (last_radio_log_fops.owner) {
-		pr_err("%s: already claimed\n", __func__);
-		return;
-	}
-
-	radio_log_base = smem_item(SMEM_CLKREGIM_BSP, &radio_log_size);
-	if (!radio_log_base) {
-		pr_err("%s: could not retrieve SMEM_CLKREGIM_BSP\n", __func__);
-		return;
-	}
-
-	entry = proc_create("last_radio_log", S_IRUGO, NULL,
-				&last_radio_log_fops);
-	if (!entry) {
-		pr_err("%s: could not create proc entry for radio log\n",
-				__func__);
-		return;
-	}
-
-	pr_err("%s: last radio log is %d bytes long\n", __func__,
-		radio_log_size);
-	last_radio_log_fops.owner = owner;
-	proc_set_size(entry, radio_log_size);
-}
-EXPORT_SYMBOL(msm_init_last_radio_log);
diff --git a/arch/arm/mach-msm/proc_comm.c b/arch/arm/mach-msm/proc_comm.c
deleted file mode 100644
index 507f5ca..0000000
--- a/arch/arm/mach-msm/proc_comm.c
+++ /dev/null
@@ -1,129 +0,0 @@
-/* arch/arm/mach-msm/proc_comm.c
- *
- * Copyright (C) 2007-2008 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/io.h>
-#include <linux/spinlock.h>
-#include <mach/msm_iomap.h>
-
-#include "proc_comm.h"
-
-static inline void msm_a2m_int(uint32_t irq)
-{
-#if defined(CONFIG_ARCH_MSM7X30)
-	writel(1 << irq, MSM_GCC_BASE + 0x8);
-#else
-	writel(1, MSM_CSR_BASE + 0x400 + (irq * 4));
-#endif
-}
-
-static inline void notify_other_proc_comm(void)
-{
-	msm_a2m_int(6);
-}
-
-#define APP_COMMAND 0x00
-#define APP_STATUS  0x04
-#define APP_DATA1   0x08
-#define APP_DATA2   0x0C
-
-#define MDM_COMMAND 0x10
-#define MDM_STATUS  0x14
-#define MDM_DATA1   0x18
-#define MDM_DATA2   0x1C
-
-static DEFINE_SPINLOCK(proc_comm_lock);
-
-/* The higher level SMD support will install this to
- * provide a way to check for and handle modem restart.
- */
-int (*msm_check_for_modem_crash)(void);
-
-/* Poll for a state change, checking for possible
- * modem crashes along the way (so we don't wait
- * forever while the ARM9 is blowing up).
- *
- * Return an error in the event of a modem crash and
- * restart so the msm_proc_comm() routine can restart
- * the operation from the beginning.
- */
-static int proc_comm_wait_for(void __iomem *addr, unsigned value)
-{
-	for (;;) {
-		if (readl(addr) == value)
-			return 0;
-
-		if (msm_check_for_modem_crash)
-			if (msm_check_for_modem_crash())
-				return -EAGAIN;
-	}
-}
-
-int msm_proc_comm(unsigned cmd, unsigned *data1, unsigned *data2)
-{
-	void __iomem *base = MSM_SHARED_RAM_BASE;
-	unsigned long flags;
-	int ret;
-
-	spin_lock_irqsave(&proc_comm_lock, flags);
-
-	for (;;) {
-		if (proc_comm_wait_for(base + MDM_STATUS, PCOM_READY))
-			continue;
-
-		writel(cmd, base + APP_COMMAND);
-		writel(data1 ? *data1 : 0, base + APP_DATA1);
-		writel(data2 ? *data2 : 0, base + APP_DATA2);
-
-		notify_other_proc_comm();
-
-		if (proc_comm_wait_for(base + APP_COMMAND, PCOM_CMD_DONE))
-			continue;
-
-		if (readl(base + APP_STATUS) != PCOM_CMD_FAIL) {
-			if (data1)
-				*data1 = readl(base + APP_DATA1);
-			if (data2)
-				*data2 = readl(base + APP_DATA2);
-			ret = 0;
-		} else {
-			ret = -EIO;
-		}
-		break;
-	}
-
-	writel(PCOM_CMD_IDLE, base + APP_COMMAND);
-
-	spin_unlock_irqrestore(&proc_comm_lock, flags);
-
-	return ret;
-}
-
-/*
- * We need to wait for the ARM9 to at least partially boot
- * up before we can continue. Since the ARM9 does resource
- * allocation, if we dont' wait we could end up crashing or in
- * and unknown state. This function should be called early to
- * wait on the ARM9.
- */
-void proc_comm_boot_wait(void)
-{
-	void __iomem *base = MSM_SHARED_RAM_BASE;
- 
-	proc_comm_wait_for(base + MDM_STATUS, PCOM_READY);
- 
-}
diff --git a/arch/arm/mach-msm/proc_comm.h b/arch/arm/mach-msm/proc_comm.h
deleted file mode 100644
index e8d043a..0000000
--- a/arch/arm/mach-msm/proc_comm.h
+++ /dev/null
@@ -1,258 +0,0 @@
-/* arch/arm/mach-msm/proc_comm.h
- *
- * Copyright (c) 2007 QUALCOMM Incorporated
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#ifndef _ARCH_ARM_MACH_MSM_PROC_COMM_H_
-#define _ARCH_ARM_MACH_MSM_PROC_COMM_H_
-
-#include <linux/init.h>
-
-enum {
-	PCOM_CMD_IDLE = 0x0,
-	PCOM_CMD_DONE,
-	PCOM_RESET_APPS,
-	PCOM_RESET_CHIP,
-	PCOM_CONFIG_NAND_MPU,
-	PCOM_CONFIG_USB_CLKS,
-	PCOM_GET_POWER_ON_STATUS,
-	PCOM_GET_WAKE_UP_STATUS,
-	PCOM_GET_BATT_LEVEL,
-	PCOM_CHG_IS_CHARGING,
-	PCOM_POWER_DOWN,
-	PCOM_USB_PIN_CONFIG,
-	PCOM_USB_PIN_SEL,
-	PCOM_SET_RTC_ALARM,
-	PCOM_NV_READ,
-	PCOM_NV_WRITE,
-	PCOM_GET_UUID_HIGH,
-	PCOM_GET_UUID_LOW,
-	PCOM_GET_HW_ENTROPY,
-	PCOM_RPC_GPIO_TLMM_CONFIG_REMOTE,
-	PCOM_CLKCTL_RPC_ENABLE,
-	PCOM_CLKCTL_RPC_DISABLE,
-	PCOM_CLKCTL_RPC_RESET,
-	PCOM_CLKCTL_RPC_SET_FLAGS,
-	PCOM_CLKCTL_RPC_SET_RATE,
-	PCOM_CLKCTL_RPC_MIN_RATE,
-	PCOM_CLKCTL_RPC_MAX_RATE,
-	PCOM_CLKCTL_RPC_RATE,
-	PCOM_CLKCTL_RPC_PLL_REQUEST,
-	PCOM_CLKCTL_RPC_ENABLED,
-	PCOM_VREG_SWITCH,
-	PCOM_VREG_SET_LEVEL,
-	PCOM_GPIO_TLMM_CONFIG_GROUP,
-	PCOM_GPIO_TLMM_UNCONFIG_GROUP,
-	PCOM_NV_WRITE_BYTES_4_7,
-	PCOM_CONFIG_DISP,
-	PCOM_GET_FTM_BOOT_COUNT,
-	PCOM_RPC_GPIO_TLMM_CONFIG_EX,
-	PCOM_PM_MPP_CONFIG,
-	PCOM_GPIO_IN,
-	PCOM_GPIO_OUT,
-	PCOM_RESET_MODEM,
-	PCOM_RESET_CHIP_IMM,
-	PCOM_PM_VID_EN,
-	PCOM_VREG_PULLDOWN,
-	PCOM_GET_MODEM_VERSION,
-	PCOM_CLK_REGIME_SEC_RESET,
-	PCOM_CLK_REGIME_SEC_RESET_ASSERT,
-	PCOM_CLK_REGIME_SEC_RESET_DEASSERT,
-	PCOM_CLK_REGIME_SEC_PLL_REQUEST_WRP,
-	PCOM_CLK_REGIME_SEC_ENABLE,
-	PCOM_CLK_REGIME_SEC_DISABLE,
-	PCOM_CLK_REGIME_SEC_IS_ON,
-	PCOM_CLK_REGIME_SEC_SEL_CLK_INV,
-	PCOM_CLK_REGIME_SEC_SEL_CLK_SRC,
-	PCOM_CLK_REGIME_SEC_SEL_CLK_DIV,
-	PCOM_CLK_REGIME_SEC_ICODEC_CLK_ENABLE,
-	PCOM_CLK_REGIME_SEC_ICODEC_CLK_DISABLE,
-	PCOM_CLK_REGIME_SEC_SEL_SPEED,
-	PCOM_CLK_REGIME_SEC_CONFIG_GP_CLK_WRP,
-	PCOM_CLK_REGIME_SEC_CONFIG_MDH_CLK_WRP,
-	PCOM_CLK_REGIME_SEC_USB_XTAL_ON,
-	PCOM_CLK_REGIME_SEC_USB_XTAL_OFF,
-	PCOM_CLK_REGIME_SEC_SET_QDSP_DME_MODE,
-	PCOM_CLK_REGIME_SEC_SWITCH_ADSP_CLK,
-	PCOM_CLK_REGIME_SEC_GET_MAX_ADSP_CLK_KHZ,
-	PCOM_CLK_REGIME_SEC_GET_I2C_CLK_KHZ,
-	PCOM_CLK_REGIME_SEC_MSM_GET_CLK_FREQ_KHZ,
-	PCOM_CLK_REGIME_SEC_SEL_VFE_SRC,
-	PCOM_CLK_REGIME_SEC_MSM_SEL_CAMCLK,
-	PCOM_CLK_REGIME_SEC_MSM_SEL_LCDCLK,
-	PCOM_CLK_REGIME_SEC_VFE_RAIL_OFF,
-	PCOM_CLK_REGIME_SEC_VFE_RAIL_ON,
-	PCOM_CLK_REGIME_SEC_GRP_RAIL_OFF,
-	PCOM_CLK_REGIME_SEC_GRP_RAIL_ON,
-	PCOM_CLK_REGIME_SEC_VDC_RAIL_OFF,
-	PCOM_CLK_REGIME_SEC_VDC_RAIL_ON,
-	PCOM_CLK_REGIME_SEC_LCD_CTRL,
-	PCOM_CLK_REGIME_SEC_REGISTER_FOR_CPU_RESOURCE,
-	PCOM_CLK_REGIME_SEC_DEREGISTER_FOR_CPU_RESOURCE,
-	PCOM_CLK_REGIME_SEC_RESOURCE_REQUEST_WRP,
-	PCOM_CLK_REGIME_MSM_SEC_SEL_CLK_OWNER,
-	PCOM_CLK_REGIME_SEC_DEVMAN_REQUEST_WRP,
-	PCOM_GPIO_CONFIG,
-	PCOM_GPIO_CONFIGURE_GROUP,
-	PCOM_GPIO_TLMM_SET_PORT,
-	PCOM_GPIO_TLMM_CONFIG_EX,
-	PCOM_SET_FTM_BOOT_COUNT,
-	PCOM_RESERVED0,
-	PCOM_RESERVED1,
-	PCOM_CUSTOMER_CMD1,
-	PCOM_CUSTOMER_CMD2,
-	PCOM_CUSTOMER_CMD3,
-	PCOM_CLK_REGIME_ENTER_APPSBL_CHG_MODE,
-	PCOM_CLK_REGIME_EXIT_APPSBL_CHG_MODE,
-	PCOM_CLK_REGIME_SEC_RAIL_DISABLE,
-	PCOM_CLK_REGIME_SEC_RAIL_ENABLE,
-	PCOM_CLK_REGIME_SEC_RAIL_CONTROL,
-	PCOM_SET_SW_WATCHDOG_STATE,
-	PCOM_PM_MPP_CONFIG_DIGITAL_INPUT,
-	PCOM_PM_MPP_CONFIG_I_SINK,
-	PCOM_RESERVED_101,
-	PCOM_MSM_HSUSB_PHY_RESET,
-	PCOM_GET_BATT_MV_LEVEL,
-	PCOM_CHG_USB_IS_PC_CONNECTED,
-	PCOM_CHG_USB_IS_CHARGER_CONNECTED,
-	PCOM_CHG_USB_IS_DISCONNECTED,
-	PCOM_CHG_USB_IS_AVAILABLE,
-	PCOM_CLK_REGIME_SEC_MSM_SEL_FREQ,
-	PCOM_CLK_REGIME_SEC_SET_PCLK_AXI_POLICY,
-	PCOM_CLKCTL_RPC_RESET_ASSERT,
-	PCOM_CLKCTL_RPC_RESET_DEASSERT,
-	PCOM_CLKCTL_RPC_RAIL_ON,
-	PCOM_CLKCTL_RPC_RAIL_OFF,
-	PCOM_CLKCTL_RPC_RAIL_ENABLE,
-	PCOM_CLKCTL_RPC_RAIL_DISABLE,
-	PCOM_CLKCTL_RPC_RAIL_CONTROL,
-	PCOM_CLKCTL_RPC_MIN_MSMC1,
-	PCOM_NUM_CMDS,
-};
-
-enum {
-	PCOM_INVALID_STATUS = 0x0,
-	PCOM_READY,
-	PCOM_CMD_RUNNING,
-	PCOM_CMD_SUCCESS,
-	PCOM_CMD_FAIL,
-	PCOM_CMD_FAIL_FALSE_RETURNED,
-	PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_SERVER,
-	PCOM_CMD_FAIL_CMD_OUT_OF_BOUNDS_CLIENT,
-	PCOM_CMD_FAIL_CMD_UNREGISTERED,
-	PCOM_CMD_FAIL_CMD_LOCKED,
-	PCOM_CMD_FAIL_SERVER_NOT_YET_READY,
-	PCOM_CMD_FAIL_BAD_DESTINATION,
-	PCOM_CMD_FAIL_SERVER_RESET,
-	PCOM_CMD_FAIL_SMSM_NOT_INIT,
-	PCOM_CMD_FAIL_PROC_COMM_BUSY,
-	PCOM_CMD_FAIL_PROC_COMM_NOT_INIT,
-
-};
-
-/* List of VREGs that support the Pull Down Resistor setting. */
-enum vreg_pdown_id {
-	PM_VREG_PDOWN_MSMA_ID,
-	PM_VREG_PDOWN_MSMP_ID,
-	PM_VREG_PDOWN_MSME1_ID,	/* Not supported in Panoramix */
-	PM_VREG_PDOWN_MSMC1_ID,	/* Not supported in PM6620 */
-	PM_VREG_PDOWN_MSMC2_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_GP3_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_MSME2_ID,	/* Supported in PM7500 and Panoramix only */
-	PM_VREG_PDOWN_GP4_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_GP1_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_TCXO_ID,
-	PM_VREG_PDOWN_PA_ID,
-	PM_VREG_PDOWN_RFTX_ID,
-	PM_VREG_PDOWN_RFRX1_ID,
-	PM_VREG_PDOWN_RFRX2_ID,
-	PM_VREG_PDOWN_SYNT_ID,
-	PM_VREG_PDOWN_WLAN_ID,
-	PM_VREG_PDOWN_USB_ID,
-	PM_VREG_PDOWN_MMC_ID,
-	PM_VREG_PDOWN_RUIM_ID,
-	PM_VREG_PDOWN_MSMC0_ID,	/* Supported in PM6610 only */
-	PM_VREG_PDOWN_GP2_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_GP5_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_GP6_ID,	/* Supported in PM7500 only */
-	PM_VREG_PDOWN_RF_ID,
-	PM_VREG_PDOWN_RF_VCO_ID,
-	PM_VREG_PDOWN_MPLL_ID,
-	PM_VREG_PDOWN_S2_ID,
-	PM_VREG_PDOWN_S3_ID,
-	PM_VREG_PDOWN_RFUBM_ID,
-
-	/* new for HAN */
-	PM_VREG_PDOWN_RF1_ID,
-	PM_VREG_PDOWN_RF2_ID,
-	PM_VREG_PDOWN_RFA_ID,
-	PM_VREG_PDOWN_CDC2_ID,
-	PM_VREG_PDOWN_RFTX2_ID,
-	PM_VREG_PDOWN_USIM_ID,
-	PM_VREG_PDOWN_USB2P6_ID,
-	PM_VREG_PDOWN_USB3P3_ID,
-	PM_VREG_PDOWN_INVALID_ID,
-
-	/* backward compatible enums only */
-	PM_VREG_PDOWN_CAM_ID = PM_VREG_PDOWN_GP1_ID,
-	PM_VREG_PDOWN_MDDI_ID = PM_VREG_PDOWN_GP2_ID,
-	PM_VREG_PDOWN_RUIM2_ID = PM_VREG_PDOWN_GP3_ID,
-	PM_VREG_PDOWN_AUX_ID = PM_VREG_PDOWN_GP4_ID,
-	PM_VREG_PDOWN_AUX2_ID = PM_VREG_PDOWN_GP5_ID,
-	PM_VREG_PDOWN_BT_ID = PM_VREG_PDOWN_GP6_ID,
-
-	PM_VREG_PDOWN_MSME_ID = PM_VREG_PDOWN_MSME1_ID,
-	PM_VREG_PDOWN_MSMC_ID = PM_VREG_PDOWN_MSMC1_ID,
-	PM_VREG_PDOWN_RFA1_ID = PM_VREG_PDOWN_RFRX2_ID,
-	PM_VREG_PDOWN_RFA2_ID = PM_VREG_PDOWN_RFTX2_ID,
-	PM_VREG_PDOWN_XO_ID = PM_VREG_PDOWN_TCXO_ID
-};
-
-enum {
-	PCOM_CLKRGM_APPS_RESET_USB_PHY	= 34,
-	PCOM_CLKRGM_APPS_RESET_USBH	= 37,
-};
-
-/* gpio info for PCOM_RPC_GPIO_TLMM_CONFIG_EX */
-
-#define GPIO_ENABLE	0
-#define GPIO_DISABLE	1
-
-#define GPIO_INPUT	0
-#define GPIO_OUTPUT	1
-
-#define GPIO_NO_PULL	0
-#define GPIO_PULL_DOWN	1
-#define GPIO_KEEPER	2
-#define GPIO_PULL_UP	3
-
-#define GPIO_2MA	0
-#define GPIO_4MA	1
-#define GPIO_6MA	2
-#define GPIO_8MA	3
-#define GPIO_10MA	4
-#define GPIO_12MA	5
-#define GPIO_14MA	6
-#define GPIO_16MA	7
-
-#define PCOM_GPIO_CFG(gpio, func, dir, pull, drvstr) \
-		((((gpio) & 0x3FF) << 4)	| \
-		((func) & 0xf)			| \
-		(((dir) & 0x1) << 14)		| \
-		(((pull) & 0x3) << 15)		| \
-		(((drvstr) & 0xF) << 17))
-
-int msm_proc_comm(unsigned cmd, unsigned *data1, unsigned *data2);
-void proc_comm_boot_wait(void);
-
-#endif
diff --git a/arch/arm/mach-msm/sirc.c b/arch/arm/mach-msm/sirc.c
deleted file mode 100644
index 689e78c..0000000
--- a/arch/arm/mach-msm/sirc.c
+++ /dev/null
@@ -1,172 +0,0 @@
-/* Copyright (c) 2008-2009, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- *
- */
-
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <asm/irq.h>
-
-static unsigned int int_enable;
-static unsigned int wake_enable;
-
-static struct sirc_regs_t sirc_regs = {
-	.int_enable       = SPSS_SIRC_INT_ENABLE,
-	.int_enable_clear = SPSS_SIRC_INT_ENABLE_CLEAR,
-	.int_enable_set   = SPSS_SIRC_INT_ENABLE_SET,
-	.int_type         = SPSS_SIRC_INT_TYPE,
-	.int_polarity     = SPSS_SIRC_INT_POLARITY,
-	.int_clear        = SPSS_SIRC_INT_CLEAR,
-};
-
-static struct sirc_cascade_regs sirc_reg_table[] = {
-	{
-		.int_status  = SPSS_SIRC_IRQ_STATUS,
-		.cascade_irq = INT_SIRC_0,
-	}
-};
-
-/* Mask off the given interrupt. Keep the int_enable mask in sync with
-   the enable reg, so it can be restored after power collapse. */
-static void sirc_irq_mask(struct irq_data *d)
-{
-	unsigned int mask;
-
-	mask = 1 << (d->irq - FIRST_SIRC_IRQ);
-	writel(mask, sirc_regs.int_enable_clear);
-	int_enable &= ~mask;
-	return;
-}
-
-/* Unmask the given interrupt. Keep the int_enable mask in sync with
-   the enable reg, so it can be restored after power collapse. */
-static void sirc_irq_unmask(struct irq_data *d)
-{
-	unsigned int mask;
-
-	mask = 1 << (d->irq - FIRST_SIRC_IRQ);
-	writel(mask, sirc_regs.int_enable_set);
-	int_enable |= mask;
-	return;
-}
-
-static void sirc_irq_ack(struct irq_data *d)
-{
-	unsigned int mask;
-
-	mask = 1 << (d->irq - FIRST_SIRC_IRQ);
-	writel(mask, sirc_regs.int_clear);
-	return;
-}
-
-static int sirc_irq_set_wake(struct irq_data *d, unsigned int on)
-{
-	unsigned int mask;
-
-	/* Used to set the interrupt enable mask during power collapse. */
-	mask = 1 << (d->irq - FIRST_SIRC_IRQ);
-	if (on)
-		wake_enable |= mask;
-	else
-		wake_enable &= ~mask;
-
-	return 0;
-}
-
-static int sirc_irq_set_type(struct irq_data *d, unsigned int flow_type)
-{
-	unsigned int mask;
-	unsigned int val;
-
-	mask = 1 << (d->irq - FIRST_SIRC_IRQ);
-	val = readl(sirc_regs.int_polarity);
-
-	if (flow_type & (IRQF_TRIGGER_LOW | IRQF_TRIGGER_FALLING))
-		val |= mask;
-	else
-		val &= ~mask;
-
-	writel(val, sirc_regs.int_polarity);
-
-	val = readl(sirc_regs.int_type);
-	if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
-		val |= mask;
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
-	} else {
-		val &= ~mask;
-		__irq_set_handler_locked(d->irq, handle_level_irq);
-	}
-
-	writel(val, sirc_regs.int_type);
-
-	return 0;
-}
-
-/* Finds the pending interrupt on the passed cascade irq and redrives it */
-static void sirc_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned int reg = 0;
-	unsigned int sirq;
-	unsigned int status;
-
-	while ((reg < ARRAY_SIZE(sirc_reg_table)) &&
-		(sirc_reg_table[reg].cascade_irq != irq))
-		reg++;
-
-	status = readl(sirc_reg_table[reg].int_status);
-	status &= SIRC_MASK;
-	if (status == 0)
-		return;
-
-	for (sirq = 0;
-	     (sirq < NR_SIRC_IRQS) && ((status & (1U << sirq)) == 0);
-	     sirq++)
-		;
-	generic_handle_irq(sirq+FIRST_SIRC_IRQ);
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-}
-
-static struct irq_chip sirc_irq_chip = {
-	.name          = "sirc",
-	.irq_ack       = sirc_irq_ack,
-	.irq_mask      = sirc_irq_mask,
-	.irq_unmask    = sirc_irq_unmask,
-	.irq_set_wake  = sirc_irq_set_wake,
-	.irq_set_type  = sirc_irq_set_type,
-};
-
-void __init msm_init_sirc(void)
-{
-	int i;
-
-	int_enable = 0;
-	wake_enable = 0;
-
-	for (i = FIRST_SIRC_IRQ; i < LAST_SIRC_IRQ; i++) {
-		irq_set_chip_and_handler(i, &sirc_irq_chip, handle_edge_irq);
-		set_irq_flags(i, IRQF_VALID);
-	}
-
-	for (i = 0; i < ARRAY_SIZE(sirc_reg_table); i++) {
-		irq_set_chained_handler(sirc_reg_table[i].cascade_irq,
-					sirc_irq_handler);
-		irq_set_irq_wake(sirc_reg_table[i].cascade_irq, 1);
-	}
-	return;
-}
-
diff --git a/arch/arm/mach-msm/smd.c b/arch/arm/mach-msm/smd.c
deleted file mode 100644
index 7550f5a..0000000
--- a/arch/arm/mach-msm/smd.c
+++ /dev/null
@@ -1,1034 +0,0 @@
-/* arch/arm/mach-msm/smd.c
- *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/fs.h>
-#include <linux/cdev.h>
-#include <linux/device.h>
-#include <linux/wait.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/list.h>
-#include <linux/slab.h>
-#include <linux/debugfs.h>
-#include <linux/delay.h>
-
-#include <mach/msm_smd.h>
-
-#include "smd_private.h"
-#include "proc_comm.h"
-
-#if defined(CONFIG_ARCH_QSD8X50)
-#define CONFIG_QDSP6 1
-#endif
-
-#define MODULE_NAME "msm_smd"
-
-enum {
-	MSM_SMD_DEBUG = 1U << 0,
-	MSM_SMSM_DEBUG = 1U << 0,
-};
-
-static int msm_smd_debug_mask;
-
-struct shared_info {
-	int ready;
-	void __iomem *state;
-};
-
-static unsigned dummy_state[SMSM_STATE_COUNT];
-
-static struct shared_info smd_info = {
-	/* FIXME: not a real __iomem pointer */
-	.state = &dummy_state,
-};
-
-module_param_named(debug_mask, msm_smd_debug_mask,
-		   int, S_IRUGO | S_IWUSR | S_IWGRP);
-
-static unsigned last_heap_free = 0xffffffff;
-
-static inline void notify_other_smsm(void)
-{
-	msm_a2m_int(5);
-#ifdef CONFIG_QDSP6
-	msm_a2m_int(8);
-#endif
-}
-
-static inline void notify_modem_smd(void)
-{
-	msm_a2m_int(0);
-}
-
-static inline void notify_dsp_smd(void)
-{
-	msm_a2m_int(8);
-}
-
-static void smd_diag(void)
-{
-	char *x;
-
-	x = smem_find(ID_DIAG_ERR_MSG, SZ_DIAG_ERR_MSG);
-	if (x != 0) {
-		x[SZ_DIAG_ERR_MSG - 1] = 0;
-		pr_debug("DIAG '%s'\n", x);
-	}
-}
-
-/* call when SMSM_RESET flag is set in the A9's smsm_state */
-static void handle_modem_crash(void)
-{
-	pr_err("ARM9 has CRASHED\n");
-	smd_diag();
-
-	/* in this case the modem or watchdog should reboot us */
-	for (;;)
-		;
-}
-
-uint32_t raw_smsm_get_state(enum smsm_state_item item)
-{
-	return readl(smd_info.state + item * 4);
-}
-
-static int check_for_modem_crash(void)
-{
-	if (raw_smsm_get_state(SMSM_STATE_MODEM) & SMSM_RESET) {
-		handle_modem_crash();
-		return -1;
-	}
-	return 0;
-}
-
-/* the spinlock is used to synchronize between the
- * irq handler and code that mutates the channel
- * list or fiddles with channel state
- */
-DEFINE_SPINLOCK(smd_lock);
-DEFINE_SPINLOCK(smem_lock);
-
-/* the mutex is used during open() and close()
- * operations to avoid races while creating or
- * destroying smd_channel structures
- */
-static DEFINE_MUTEX(smd_creation_mutex);
-
-static int smd_initialized;
-
-LIST_HEAD(smd_ch_closed_list);
-LIST_HEAD(smd_ch_list_modem);
-LIST_HEAD(smd_ch_list_dsp);
-
-static unsigned char smd_ch_allocated[64];
-static struct work_struct probe_work;
-
-/* how many bytes are available for reading */
-static int smd_stream_read_avail(struct smd_channel *ch)
-{
-	return (ch->recv->head - ch->recv->tail) & ch->fifo_mask;
-}
-
-/* how many bytes we are free to write */
-static int smd_stream_write_avail(struct smd_channel *ch)
-{
-	return ch->fifo_mask -
-		((ch->send->head - ch->send->tail) & ch->fifo_mask);
-}
-
-static int smd_packet_read_avail(struct smd_channel *ch)
-{
-	if (ch->current_packet) {
-		int n = smd_stream_read_avail(ch);
-		if (n > ch->current_packet)
-			n = ch->current_packet;
-		return n;
-	} else {
-		return 0;
-	}
-}
-
-static int smd_packet_write_avail(struct smd_channel *ch)
-{
-	int n = smd_stream_write_avail(ch);
-	return n > SMD_HEADER_SIZE ? n - SMD_HEADER_SIZE : 0;
-}
-
-static int ch_is_open(struct smd_channel *ch)
-{
-	return (ch->recv->state == SMD_SS_OPENED) &&
-		(ch->send->state == SMD_SS_OPENED);
-}
-
-/* provide a pointer and length to readable data in the fifo */
-static unsigned ch_read_buffer(struct smd_channel *ch, void **ptr)
-{
-	unsigned head = ch->recv->head;
-	unsigned tail = ch->recv->tail;
-	*ptr = (void *) (ch->recv_data + tail);
-
-	if (tail <= head)
-		return head - tail;
-	else
-		return ch->fifo_size - tail;
-}
-
-/* advance the fifo read pointer after data from ch_read_buffer is consumed */
-static void ch_read_done(struct smd_channel *ch, unsigned count)
-{
-	BUG_ON(count > smd_stream_read_avail(ch));
-	ch->recv->tail = (ch->recv->tail + count) & ch->fifo_mask;
-	ch->send->fTAIL = 1;
-}
-
-/* basic read interface to ch_read_{buffer,done} used
- * by smd_*_read() and update_packet_state()
- * will read-and-discard if the _data pointer is null
- */
-static int ch_read(struct smd_channel *ch, void *_data, int len)
-{
-	void *ptr;
-	unsigned n;
-	unsigned char *data = _data;
-	int orig_len = len;
-
-	while (len > 0) {
-		n = ch_read_buffer(ch, &ptr);
-		if (n == 0)
-			break;
-
-		if (n > len)
-			n = len;
-		if (_data)
-			memcpy(data, ptr, n);
-
-		data += n;
-		len -= n;
-		ch_read_done(ch, n);
-	}
-
-	return orig_len - len;
-}
-
-static void update_stream_state(struct smd_channel *ch)
-{
-	/* streams have no special state requiring updating */
-}
-
-static void update_packet_state(struct smd_channel *ch)
-{
-	unsigned hdr[5];
-	int r;
-
-	/* can't do anything if we're in the middle of a packet */
-	if (ch->current_packet != 0)
-		return;
-
-	/* don't bother unless we can get the full header */
-	if (smd_stream_read_avail(ch) < SMD_HEADER_SIZE)
-		return;
-
-	r = ch_read(ch, hdr, SMD_HEADER_SIZE);
-	BUG_ON(r != SMD_HEADER_SIZE);
-
-	ch->current_packet = hdr[0];
-}
-
-/* provide a pointer and length to next free space in the fifo */
-static unsigned ch_write_buffer(struct smd_channel *ch, void **ptr)
-{
-	unsigned head = ch->send->head;
-	unsigned tail = ch->send->tail;
-	*ptr = (void *) (ch->send_data + head);
-
-	if (head < tail) {
-		return tail - head - 1;
-	} else {
-		if (tail == 0)
-			return ch->fifo_size - head - 1;
-		else
-			return ch->fifo_size - head;
-	}
-}
-
-/* advace the fifo write pointer after freespace
- * from ch_write_buffer is filled
- */
-static void ch_write_done(struct smd_channel *ch, unsigned count)
-{
-	BUG_ON(count > smd_stream_write_avail(ch));
-	ch->send->head = (ch->send->head + count) & ch->fifo_mask;
-	ch->send->fHEAD = 1;
-}
-
-static void ch_set_state(struct smd_channel *ch, unsigned n)
-{
-	if (n == SMD_SS_OPENED) {
-		ch->send->fDSR = 1;
-		ch->send->fCTS = 1;
-		ch->send->fCD = 1;
-	} else {
-		ch->send->fDSR = 0;
-		ch->send->fCTS = 0;
-		ch->send->fCD = 0;
-	}
-	ch->send->state = n;
-	ch->send->fSTATE = 1;
-	ch->notify_other_cpu();
-}
-
-static void do_smd_probe(void)
-{
-	struct smem_shared *shared = (void *) MSM_SHARED_RAM_BASE;
-	if (shared->heap_info.free_offset != last_heap_free) {
-		last_heap_free = shared->heap_info.free_offset;
-		schedule_work(&probe_work);
-	}
-}
-
-static void smd_state_change(struct smd_channel *ch,
-			     unsigned last, unsigned next)
-{
-	ch->last_state = next;
-
-	pr_debug("ch %d %d -> %d\n", ch->n, last, next);
-
-	switch (next) {
-	case SMD_SS_OPENING:
-		ch->recv->tail = 0;
-	case SMD_SS_OPENED:
-		if (ch->send->state != SMD_SS_OPENED)
-			ch_set_state(ch, SMD_SS_OPENED);
-		ch->notify(ch->priv, SMD_EVENT_OPEN);
-		break;
-	case SMD_SS_FLUSHING:
-	case SMD_SS_RESET:
-		/* we should force them to close? */
-	default:
-		ch->notify(ch->priv, SMD_EVENT_CLOSE);
-	}
-}
-
-static void handle_smd_irq(struct list_head *list, void (*notify)(void))
-{
-	unsigned long flags;
-	struct smd_channel *ch;
-	int do_notify = 0;
-	unsigned ch_flags;
-	unsigned tmp;
-
-	spin_lock_irqsave(&smd_lock, flags);
-	list_for_each_entry(ch, list, ch_list) {
-		ch_flags = 0;
-		if (ch_is_open(ch)) {
-			if (ch->recv->fHEAD) {
-				ch->recv->fHEAD = 0;
-				ch_flags |= 1;
-				do_notify |= 1;
-			}
-			if (ch->recv->fTAIL) {
-				ch->recv->fTAIL = 0;
-				ch_flags |= 2;
-				do_notify |= 1;
-			}
-			if (ch->recv->fSTATE) {
-				ch->recv->fSTATE = 0;
-				ch_flags |= 4;
-				do_notify |= 1;
-			}
-		}
-		tmp = ch->recv->state;
-		if (tmp != ch->last_state)
-			smd_state_change(ch, ch->last_state, tmp);
-		if (ch_flags) {
-			ch->update_state(ch);
-			ch->notify(ch->priv, SMD_EVENT_DATA);
-		}
-	}
-	if (do_notify)
-		notify();
-	spin_unlock_irqrestore(&smd_lock, flags);
-	do_smd_probe();
-}
-
-static irqreturn_t smd_modem_irq_handler(int irq, void *data)
-{
-	handle_smd_irq(&smd_ch_list_modem, notify_modem_smd);
-	return IRQ_HANDLED;
-}
-
-#if defined(CONFIG_QDSP6)
-static irqreturn_t smd_dsp_irq_handler(int irq, void *data)
-{
-	handle_smd_irq(&smd_ch_list_dsp, notify_dsp_smd);
-	return IRQ_HANDLED;
-}
-#endif
-
-static void smd_fake_irq_handler(unsigned long arg)
-{
-	handle_smd_irq(&smd_ch_list_modem, notify_modem_smd);
-	handle_smd_irq(&smd_ch_list_dsp, notify_dsp_smd);
-}
-
-static DECLARE_TASKLET(smd_fake_irq_tasklet, smd_fake_irq_handler, 0);
-
-static inline int smd_need_int(struct smd_channel *ch)
-{
-	if (ch_is_open(ch)) {
-		if (ch->recv->fHEAD || ch->recv->fTAIL || ch->recv->fSTATE)
-			return 1;
-		if (ch->recv->state != ch->last_state)
-			return 1;
-	}
-	return 0;
-}
-
-void smd_sleep_exit(void)
-{
-	unsigned long flags;
-	struct smd_channel *ch;
-	int need_int = 0;
-
-	spin_lock_irqsave(&smd_lock, flags);
-	list_for_each_entry(ch, &smd_ch_list_modem, ch_list) {
-		if (smd_need_int(ch)) {
-			need_int = 1;
-			break;
-		}
-	}
-	list_for_each_entry(ch, &smd_ch_list_dsp, ch_list) {
-		if (smd_need_int(ch)) {
-			need_int = 1;
-			break;
-		}
-	}
-	spin_unlock_irqrestore(&smd_lock, flags);
-	do_smd_probe();
-
-	if (need_int) {
-		if (msm_smd_debug_mask & MSM_SMD_DEBUG)
-			pr_info("smd_sleep_exit need interrupt\n");
-		tasklet_schedule(&smd_fake_irq_tasklet);
-	}
-}
-
-
-void smd_kick(smd_channel_t *ch)
-{
-	unsigned long flags;
-	unsigned tmp;
-
-	spin_lock_irqsave(&smd_lock, flags);
-	ch->update_state(ch);
-	tmp = ch->recv->state;
-	if (tmp != ch->last_state) {
-		ch->last_state = tmp;
-		if (tmp == SMD_SS_OPENED)
-			ch->notify(ch->priv, SMD_EVENT_OPEN);
-		else
-			ch->notify(ch->priv, SMD_EVENT_CLOSE);
-	}
-	ch->notify(ch->priv, SMD_EVENT_DATA);
-	ch->notify_other_cpu();
-	spin_unlock_irqrestore(&smd_lock, flags);
-}
-
-static int smd_is_packet(int chn, unsigned type)
-{
-	type &= SMD_KIND_MASK;
-	if (type == SMD_KIND_PACKET)
-		return 1;
-	if (type == SMD_KIND_STREAM)
-		return 0;
-
-	/* older AMSS reports SMD_KIND_UNKNOWN always */
-	if ((chn > 4) || (chn == 1))
-		return 1;
-	else
-		return 0;
-}
-
-static int smd_stream_write(smd_channel_t *ch, const void *_data, int len)
-{
-	void *ptr;
-	const unsigned char *buf = _data;
-	unsigned xfer;
-	int orig_len = len;
-
-	if (len < 0)
-		return -EINVAL;
-
-	while ((xfer = ch_write_buffer(ch, &ptr)) != 0) {
-		if (!ch_is_open(ch))
-			break;
-		if (xfer > len)
-			xfer = len;
-		memcpy(ptr, buf, xfer);
-		ch_write_done(ch, xfer);
-		len -= xfer;
-		buf += xfer;
-		if (len == 0)
-			break;
-	}
-
-	ch->notify_other_cpu();
-
-	return orig_len - len;
-}
-
-static int smd_packet_write(smd_channel_t *ch, const void *_data, int len)
-{
-	unsigned hdr[5];
-
-	if (len < 0)
-		return -EINVAL;
-
-	if (smd_stream_write_avail(ch) < (len + SMD_HEADER_SIZE))
-		return -ENOMEM;
-
-	hdr[0] = len;
-	hdr[1] = hdr[2] = hdr[3] = hdr[4] = 0;
-
-	smd_stream_write(ch, hdr, sizeof(hdr));
-	smd_stream_write(ch, _data, len);
-
-	return len;
-}
-
-static int smd_stream_read(smd_channel_t *ch, void *data, int len)
-{
-	int r;
-
-	if (len < 0)
-		return -EINVAL;
-
-	r = ch_read(ch, data, len);
-	if (r > 0)
-		ch->notify_other_cpu();
-
-	return r;
-}
-
-static int smd_packet_read(smd_channel_t *ch, void *data, int len)
-{
-	unsigned long flags;
-	int r;
-
-	if (len < 0)
-		return -EINVAL;
-
-	if (len > ch->current_packet)
-		len = ch->current_packet;
-
-	r = ch_read(ch, data, len);
-	if (r > 0)
-		ch->notify_other_cpu();
-
-	spin_lock_irqsave(&smd_lock, flags);
-	ch->current_packet -= r;
-	update_packet_state(ch);
-	spin_unlock_irqrestore(&smd_lock, flags);
-
-	return r;
-}
-
-static int smd_alloc_channel(const char *name, uint32_t cid, uint32_t type)
-{
-	struct smd_channel *ch;
-
-	ch = kzalloc(sizeof(struct smd_channel), GFP_KERNEL);
-	if (ch == 0) {
-		pr_err("smd_alloc_channel() out of memory\n");
-		return -1;
-	}
-	ch->n = cid;
-
-	if (_smd_alloc_channel(ch)) {
-		kfree(ch);
-		return -1;
-	}
-
-	ch->fifo_mask = ch->fifo_size - 1;
-	ch->type = type;
-
-	if ((type & SMD_TYPE_MASK) == SMD_TYPE_APPS_MODEM)
-		ch->notify_other_cpu = notify_modem_smd;
-	else
-		ch->notify_other_cpu = notify_dsp_smd;
-
-	if (smd_is_packet(cid, type)) {
-		ch->read = smd_packet_read;
-		ch->write = smd_packet_write;
-		ch->read_avail = smd_packet_read_avail;
-		ch->write_avail = smd_packet_write_avail;
-		ch->update_state = update_packet_state;
-	} else {
-		ch->read = smd_stream_read;
-		ch->write = smd_stream_write;
-		ch->read_avail = smd_stream_read_avail;
-		ch->write_avail = smd_stream_write_avail;
-		ch->update_state = update_stream_state;
-	}
-
-	if ((type & 0xff) == 0)
-		memcpy(ch->name, "SMD_", 4);
-	else
-		memcpy(ch->name, "DSP_", 4);
-	memcpy(ch->name + 4, name, 20);
-	ch->name[23] = 0;
-	ch->pdev.name = ch->name;
-	ch->pdev.id = -1;
-
-	pr_debug("smd_alloc_channel() cid=%02d size=%05d '%s'\n",
-		ch->n, ch->fifo_size, ch->name);
-
-	mutex_lock(&smd_creation_mutex);
-	list_add(&ch->ch_list, &smd_ch_closed_list);
-	mutex_unlock(&smd_creation_mutex);
-
-	platform_device_register(&ch->pdev);
-	return 0;
-}
-
-static void smd_channel_probe_worker(struct work_struct *work)
-{
-	struct smd_alloc_elm *shared;
-	unsigned ctype;
-	unsigned type;
-	unsigned n;
-
-	shared = smem_find(ID_CH_ALLOC_TBL, sizeof(*shared) * 64);
-	if (!shared) {
-		pr_err("cannot find allocation table\n");
-		return;
-	}
-	for (n = 0; n < 64; n++) {
-		if (smd_ch_allocated[n])
-			continue;
-		if (!shared[n].ref_count)
-			continue;
-		if (!shared[n].name[0])
-			continue;
-		ctype = shared[n].ctype;
-		type = ctype & SMD_TYPE_MASK;
-
-		/* DAL channels are stream but neither the modem,
-		 * nor the DSP correctly indicate this.  Fixup manually.
-		 */
-		if (!memcmp(shared[n].name, "DAL", 3))
-			ctype = (ctype & (~SMD_KIND_MASK)) | SMD_KIND_STREAM;
-
-		type = shared[n].ctype & SMD_TYPE_MASK;
-		if ((type == SMD_TYPE_APPS_MODEM) ||
-		    (type == SMD_TYPE_APPS_DSP))
-			if (!smd_alloc_channel(shared[n].name, shared[n].cid, ctype))
-				smd_ch_allocated[n] = 1;
-	}
-}
-
-static void do_nothing_notify(void *priv, unsigned flags)
-{
-}
-
-struct smd_channel *smd_get_channel(const char *name)
-{
-	struct smd_channel *ch;
-
-	mutex_lock(&smd_creation_mutex);
-	list_for_each_entry(ch, &smd_ch_closed_list, ch_list) {
-		if (!strcmp(name, ch->name)) {
-			list_del(&ch->ch_list);
-			mutex_unlock(&smd_creation_mutex);
-			return ch;
-		}
-	}
-	mutex_unlock(&smd_creation_mutex);
-
-	return NULL;
-}
-
-int smd_open(const char *name, smd_channel_t **_ch,
-	     void *priv, void (*notify)(void *, unsigned))
-{
-	struct smd_channel *ch;
-	unsigned long flags;
-
-	if (smd_initialized == 0) {
-		pr_info("smd_open() before smd_init()\n");
-		return -ENODEV;
-	}
-
-	ch = smd_get_channel(name);
-	if (!ch)
-		return -ENODEV;
-
-	if (notify == 0)
-		notify = do_nothing_notify;
-
-	ch->notify = notify;
-	ch->current_packet = 0;
-	ch->last_state = SMD_SS_CLOSED;
-	ch->priv = priv;
-
-	*_ch = ch;
-
-	spin_lock_irqsave(&smd_lock, flags);
-
-	if ((ch->type & SMD_TYPE_MASK) == SMD_TYPE_APPS_MODEM)
-		list_add(&ch->ch_list, &smd_ch_list_modem);
-	else
-		list_add(&ch->ch_list, &smd_ch_list_dsp);
-
-	/* If the remote side is CLOSING, we need to get it to
-	 * move to OPENING (which we'll do by moving from CLOSED to
-	 * OPENING) and then get it to move from OPENING to
-	 * OPENED (by doing the same state change ourselves).
-	 *
-	 * Otherwise, it should be OPENING and we can move directly
-	 * to OPENED so that it will follow.
-	 */
-	if (ch->recv->state == SMD_SS_CLOSING) {
-		ch->send->head = 0;
-		ch_set_state(ch, SMD_SS_OPENING);
-	} else {
-		ch_set_state(ch, SMD_SS_OPENED);
-	}
-	spin_unlock_irqrestore(&smd_lock, flags);
-	smd_kick(ch);
-
-	return 0;
-}
-
-int smd_close(smd_channel_t *ch)
-{
-	unsigned long flags;
-
-	if (ch == 0)
-		return -1;
-
-	spin_lock_irqsave(&smd_lock, flags);
-	ch->notify = do_nothing_notify;
-	list_del(&ch->ch_list);
-	ch_set_state(ch, SMD_SS_CLOSED);
-	spin_unlock_irqrestore(&smd_lock, flags);
-
-	mutex_lock(&smd_creation_mutex);
-	list_add(&ch->ch_list, &smd_ch_closed_list);
-	mutex_unlock(&smd_creation_mutex);
-
-	return 0;
-}
-
-int smd_read(smd_channel_t *ch, void *data, int len)
-{
-	return ch->read(ch, data, len);
-}
-
-int smd_write(smd_channel_t *ch, const void *data, int len)
-{
-	return ch->write(ch, data, len);
-}
-
-int smd_write_atomic(smd_channel_t *ch, const void *data, int len)
-{
-	unsigned long flags;
-	int res;
-	spin_lock_irqsave(&smd_lock, flags);
-	res = ch->write(ch, data, len);
-	spin_unlock_irqrestore(&smd_lock, flags);
-	return res;
-}
-
-int smd_read_avail(smd_channel_t *ch)
-{
-	return ch->read_avail(ch);
-}
-
-int smd_write_avail(smd_channel_t *ch)
-{
-	return ch->write_avail(ch);
-}
-
-int smd_wait_until_readable(smd_channel_t *ch, int bytes)
-{
-	return -1;
-}
-
-int smd_wait_until_writable(smd_channel_t *ch, int bytes)
-{
-	return -1;
-}
-
-int smd_cur_packet_size(smd_channel_t *ch)
-{
-	return ch->current_packet;
-}
-
-
-/* ------------------------------------------------------------------------- */
-
-void *smem_alloc(unsigned id, unsigned size)
-{
-	return smem_find(id, size);
-}
-
-void __iomem *smem_item(unsigned id, unsigned *size)
-{
-	struct smem_shared *shared = (void *) MSM_SHARED_RAM_BASE;
-	struct smem_heap_entry *toc = shared->heap_toc;
-
-	if (id >= SMEM_NUM_ITEMS)
-		return NULL;
-
-	if (toc[id].allocated) {
-		*size = toc[id].size;
-		return (MSM_SHARED_RAM_BASE + toc[id].offset);
-	} else {
-		*size = 0;
-	}
-
-	return NULL;
-}
-
-void *smem_find(unsigned id, unsigned size_in)
-{
-	unsigned size;
-	void *ptr;
-
-	ptr = smem_item(id, &size);
-	if (!ptr)
-		return 0;
-
-	size_in = ALIGN(size_in, 8);
-	if (size_in != size) {
-		pr_err("smem_find(%d, %d): wrong size %d\n",
-		       id, size_in, size);
-		return 0;
-	}
-
-	return ptr;
-}
-
-static irqreturn_t smsm_irq_handler(int irq, void *data)
-{
-	unsigned long flags;
-	unsigned apps, modm;
-
-	spin_lock_irqsave(&smem_lock, flags);
-
-	apps = raw_smsm_get_state(SMSM_STATE_APPS);
-	modm = raw_smsm_get_state(SMSM_STATE_MODEM);
-
-	if (msm_smd_debug_mask & MSM_SMSM_DEBUG)
-		pr_info("<SM %08x %08x>\n", apps, modm);
-	if (modm & SMSM_RESET)
-		handle_modem_crash();
-
-	do_smd_probe();
-
-	spin_unlock_irqrestore(&smem_lock, flags);
-	return IRQ_HANDLED;
-}
-
-int smsm_change_state(enum smsm_state_item item,
-		      uint32_t clear_mask, uint32_t set_mask)
-{
-	void __iomem *addr = smd_info.state + item * 4;
-	unsigned long flags;
-	unsigned state;
-
-	if (!smd_info.ready)
-		return -EIO;
-
-	spin_lock_irqsave(&smem_lock, flags);
-
-	if (raw_smsm_get_state(SMSM_STATE_MODEM) & SMSM_RESET)
-		handle_modem_crash();
-
-	state = (readl(addr) & ~clear_mask) | set_mask;
-	writel(state, addr);
-
-	if (msm_smd_debug_mask & MSM_SMSM_DEBUG)
-		pr_info("smsm_change_state %d %x\n", item, state);
-	notify_other_smsm();
-
-	spin_unlock_irqrestore(&smem_lock, flags);
-
-	return 0;
-}
-
-uint32_t smsm_get_state(enum smsm_state_item item)
-{
-	unsigned long flags;
-	uint32_t rv;
-
-	spin_lock_irqsave(&smem_lock, flags);
-
-	rv = readl(smd_info.state + item * 4);
-
-	if (item == SMSM_STATE_MODEM && (rv & SMSM_RESET))
-		handle_modem_crash();
-
-	spin_unlock_irqrestore(&smem_lock, flags);
-
-	return rv;
-}
-
-#ifdef CONFIG_ARCH_MSM_SCORPION
-
-int smsm_set_sleep_duration(uint32_t delay)
-{
-	struct msm_dem_slave_data *ptr;
-
-	ptr = smem_find(SMEM_APPS_DEM_SLAVE_DATA, sizeof(*ptr));
-	if (ptr == NULL) {
-		pr_err("smsm_set_sleep_duration <SM NO APPS_DEM_SLAVE_DATA>\n");
-		return -EIO;
-	}
-	if (msm_smd_debug_mask & MSM_SMSM_DEBUG)
-		pr_info("smsm_set_sleep_duration %d -> %d\n",
-		       ptr->sleep_time, delay);
-	ptr->sleep_time = delay;
-	return 0;
-}
-
-#else
-
-int smsm_set_sleep_duration(uint32_t delay)
-{
-	uint32_t *ptr;
-
-	ptr = smem_find(SMEM_SMSM_SLEEP_DELAY, sizeof(*ptr));
-	if (ptr == NULL) {
-		pr_err("smsm_set_sleep_duration <SM NO SLEEP_DELAY>\n");
-		return -EIO;
-	}
-	if (msm_smd_debug_mask & MSM_SMSM_DEBUG)
-		pr_info("smsm_set_sleep_duration %d -> %d\n",
-		       *ptr, delay);
-	*ptr = delay;
-	return 0;
-}
-
-#endif
-
-int smd_core_init(void)
-{
-	int r;
-
-	/* wait for essential items to be initialized */
-	for (;;) {
-		unsigned size;
-		void __iomem *state;
-		state = smem_item(SMEM_SMSM_SHARED_STATE, &size);
-		if (size == SMSM_V1_SIZE || size == SMSM_V2_SIZE) {
-			smd_info.state = state;
-			break;
-		}
-	}
-
-	smd_info.ready = 1;
-
-	r = request_irq(INT_A9_M2A_0, smd_modem_irq_handler,
-			IRQF_TRIGGER_RISING, "smd_dev", 0);
-	if (r < 0)
-		return r;
-	r = enable_irq_wake(INT_A9_M2A_0);
-	if (r < 0)
-		pr_err("smd_core_init: enable_irq_wake failed for A9_M2A_0\n");
-
-	r = request_irq(INT_A9_M2A_5, smsm_irq_handler,
-			IRQF_TRIGGER_RISING, "smsm_dev", 0);
-	if (r < 0) {
-		free_irq(INT_A9_M2A_0, 0);
-		return r;
-	}
-	r = enable_irq_wake(INT_A9_M2A_5);
-	if (r < 0)
-		pr_err("smd_core_init: enable_irq_wake failed for A9_M2A_5\n");
-
-#if defined(CONFIG_QDSP6)
-	r = request_irq(INT_ADSP_A11, smd_dsp_irq_handler,
-			IRQF_TRIGGER_RISING, "smd_dsp", 0);
-	if (r < 0) {
-		free_irq(INT_A9_M2A_0, 0);
-		free_irq(INT_A9_M2A_5, 0);
-		return r;
-	}
-#endif
-
-	/* check for any SMD channels that may already exist */
-	do_smd_probe();
-
-	/* indicate that we're up and running */
-	smsm_change_state(SMSM_STATE_APPS,
-			  ~0, SMSM_INIT | SMSM_SMDINIT | SMSM_RPCINIT | SMSM_RUN);
-#ifdef CONFIG_ARCH_MSM_SCORPION
-	smsm_change_state(SMSM_STATE_APPS_DEM, ~0, 0);
-#endif
-
-	return 0;
-}
-
-static int msm_smd_probe(struct platform_device *pdev)
-{
-	/*
-	 * If we haven't waited for the ARM9 to boot up till now,
-	 * then we need to wait here. Otherwise this should just
-	 * return immediately.
-	 */
-	proc_comm_boot_wait();
-
-	INIT_WORK(&probe_work, smd_channel_probe_worker);
-
-	if (smd_core_init()) {
-		pr_err("smd_core_init() failed\n");
-		return -1;
-	}
-
-	do_smd_probe();
-
-	msm_check_for_modem_crash = check_for_modem_crash;
-
-	msm_init_last_radio_log(THIS_MODULE);
-
-	smd_initialized = 1;
-
-	return 0;
-}
-
-static struct platform_driver msm_smd_driver = {
-	.probe = msm_smd_probe,
-	.driver = {
-		.name = MODULE_NAME,
-	},
-};
-
-static int __init msm_smd_init(void)
-{
-	return platform_driver_register(&msm_smd_driver);
-}
-
-module_init(msm_smd_init);
-
-MODULE_DESCRIPTION("MSM Shared Memory Core");
-MODULE_AUTHOR("Brian Swetland <swetland@google.com>");
-MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-msm/smd_debug.c b/arch/arm/mach-msm/smd_debug.c
deleted file mode 100644
index 8056b3e..0000000
--- a/arch/arm/mach-msm/smd_debug.c
+++ /dev/null
@@ -1,311 +0,0 @@
-/* arch/arm/mach-msm/smd_debug.c
- *
- * Copyright (C) 2007 Google, Inc.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/debugfs.h>
-#include <linux/list.h>
-
-#include <mach/msm_iomap.h>
-
-#include "smd_private.h"
-
-#if defined(CONFIG_DEBUG_FS)
-
-static char *chstate(unsigned n)
-{
-	switch (n) {
-	case SMD_SS_CLOSED:
-		return "CLOSED";
-	case SMD_SS_OPENING:
-		return "OPENING";
-	case SMD_SS_OPENED:
-		return "OPENED";
-	case SMD_SS_FLUSHING:
-		return "FLUSHING";
-	case SMD_SS_CLOSING:
-		return "CLOSING";
-	case SMD_SS_RESET:
-		return "RESET";
-	case SMD_SS_RESET_OPENING:
-		return "ROPENING";
-	default:
-		return "UNKNOWN";
-	}
-}
-
-
-static int dump_ch(char *buf, int max, struct smd_channel *ch)
-{
-	volatile struct smd_half_channel *s = ch->send;
-	volatile struct smd_half_channel *r = ch->recv;
-
-	return scnprintf(
-		buf, max,
-		"ch%02d:"
-		" %8s(%05d/%05d) %c%c%c%c%c%c%c <->"
-		" %8s(%05d/%05d) %c%c%c%c%c%c%c '%s'\n", ch->n,
-		chstate(s->state), s->tail, s->head,
-		s->fDSR ? 'D' : 'd',
-		s->fCTS ? 'C' : 'c',
-		s->fCD ? 'C' : 'c',
-		s->fRI ? 'I' : 'i',
-		s->fHEAD ? 'W' : 'w',
-		s->fTAIL ? 'R' : 'r',
-		s->fSTATE ? 'S' : 's',
-		chstate(r->state), r->tail, r->head,
-		r->fDSR ? 'D' : 'd',
-		r->fCTS ? 'R' : 'r',
-		r->fCD ? 'C' : 'c',
-		r->fRI ? 'I' : 'i',
-		r->fHEAD ? 'W' : 'w',
-		r->fTAIL ? 'R' : 'r',
-		r->fSTATE ? 'S' : 's',
-		ch->name
-		);
-}
-
-static int debug_read_stat(char *buf, int max)
-{
-	char *msg;
-	int i = 0;
-
-	msg = smem_find(ID_DIAG_ERR_MSG, SZ_DIAG_ERR_MSG);
-
-	if (raw_smsm_get_state(SMSM_STATE_MODEM) & SMSM_RESET)
-		i += scnprintf(buf + i, max - i,
-			       "smsm: ARM9 HAS CRASHED\n");
-
-	i += scnprintf(buf + i, max - i, "smsm: a9: %08x a11: %08x\n",
-		       raw_smsm_get_state(SMSM_STATE_MODEM),
-		       raw_smsm_get_state(SMSM_STATE_APPS));
-#ifdef CONFIG_ARCH_MSM_SCORPION
-	i += scnprintf(buf + i, max - i, "smsm dem: apps: %08x modem: %08x "
-		       "qdsp6: %08x power: %08x time: %08x\n",
-		       raw_smsm_get_state(SMSM_STATE_APPS_DEM),
-		       raw_smsm_get_state(SMSM_STATE_MODEM_DEM),
-		       raw_smsm_get_state(SMSM_STATE_QDSP6_DEM),
-		       raw_smsm_get_state(SMSM_STATE_POWER_MASTER_DEM),
-		       raw_smsm_get_state(SMSM_STATE_TIME_MASTER_DEM));
-#endif
-	if (msg) {
-		msg[SZ_DIAG_ERR_MSG - 1] = 0;
-		i += scnprintf(buf + i, max - i, "diag: '%s'\n", msg);
-	}
-	return i;
-}
-
-static int debug_read_mem(char *buf, int max)
-{
-	unsigned n;
-	struct smem_shared *shared = (void *) MSM_SHARED_RAM_BASE;
-	struct smem_heap_entry *toc = shared->heap_toc;
-	int i = 0;
-
-	i += scnprintf(buf + i, max - i,
-		       "heap: init=%d free=%d remain=%d\n",
-		       shared->heap_info.initialized,
-		       shared->heap_info.free_offset,
-		       shared->heap_info.heap_remaining);
-
-	for (n = 0; n < SMEM_NUM_ITEMS; n++) {
-		if (toc[n].allocated == 0)
-			continue;
-		i += scnprintf(buf + i, max - i,
-			       "%04d: offset %08x size %08x\n",
-			       n, toc[n].offset, toc[n].size);
-	}
-	return i;
-}
-
-static int debug_read_ch(char *buf, int max)
-{
-	struct smd_channel *ch;
-	unsigned long flags;
-	int i = 0;
-
-	spin_lock_irqsave(&smd_lock, flags);
-	list_for_each_entry(ch, &smd_ch_list_dsp, ch_list)
-		i += dump_ch(buf + i, max - i, ch);
-	list_for_each_entry(ch, &smd_ch_list_modem, ch_list)
-		i += dump_ch(buf + i, max - i, ch);
-	list_for_each_entry(ch, &smd_ch_closed_list, ch_list)
-		i += dump_ch(buf + i, max - i, ch);
-	spin_unlock_irqrestore(&smd_lock, flags);
-
-	return i;
-}
-
-static int debug_read_version(char *buf, int max)
-{
-	struct smem_shared *shared = (void *) MSM_SHARED_RAM_BASE;
-	unsigned version = shared->version[VERSION_MODEM];
-	return sprintf(buf, "%d.%d\n", version >> 16, version & 0xffff);
-}
-
-static int debug_read_build_id(char *buf, int max)
-{
-	unsigned size;
-	void *data;
-
-	data = smem_item(SMEM_HW_SW_BUILD_ID, &size);
-	if (!data)
-		return 0;
-
-	if (size >= max)
-		size = max;
-	memcpy(buf, data, size);
-
-	return size;
-}
-
-static int debug_read_alloc_tbl(char *buf, int max)
-{
-	struct smd_alloc_elm *shared;
-	int n, i = 0;
-
-	shared = smem_find(ID_CH_ALLOC_TBL, sizeof(*shared) * 64);
-
-	for (n = 0; n < 64; n++) {
-		if (shared[n].ref_count == 0)
-			continue;
-		i += scnprintf(buf + i, max - i,
-			       "%03d: %-20s cid=%02d type=%03d "
-			       "kind=%02d ref_count=%d\n",
-			       n, shared[n].name, shared[n].cid,
-			       shared[n].ctype & 0xff,
-			       (shared[n].ctype >> 8) & 0xf,
-			       shared[n].ref_count);
-	}
-
-	return i;
-}
-
-#define DEBUG_BUFMAX 4096
-static char debug_buffer[DEBUG_BUFMAX];
-
-static ssize_t debug_read(struct file *file, char __user *buf,
-			  size_t count, loff_t *ppos)
-{
-	int (*fill)(char *buf, int max) = file->private_data;
-	int bsize = fill(debug_buffer, DEBUG_BUFMAX);
-	return simple_read_from_buffer(buf, count, ppos, debug_buffer, bsize);
-}
-
-static const struct file_operations debug_ops = {
-	.read = debug_read,
-	.open = simple_open,
-	.llseek = default_llseek,
-};
-
-static void debug_create(const char *name, umode_t mode,
-			 struct dentry *dent,
-			 int (*fill)(char *buf, int max))
-{
-	debugfs_create_file(name, mode, dent, fill, &debug_ops);
-}
-
-int __init smd_debugfs_init(void)
-{
-	struct dentry *dent;
-
-	dent = debugfs_create_dir("smd", 0);
-	if (IS_ERR(dent))
-		return 1;
-
-	debug_create("ch", 0444, dent, debug_read_ch);
-	debug_create("stat", 0444, dent, debug_read_stat);
-	debug_create("mem", 0444, dent, debug_read_mem);
-	debug_create("version", 0444, dent, debug_read_version);
-	debug_create("tbl", 0444, dent, debug_read_alloc_tbl);
-	debug_create("build", 0444, dent, debug_read_build_id);
-
-	return 0;
-}
-
-#endif
-
-
-#define MAX_NUM_SLEEP_CLIENTS		64
-#define MAX_SLEEP_NAME_LEN		8
-
-#define NUM_GPIO_INT_REGISTERS		6
-#define GPIO_SMEM_NUM_GROUPS		2
-#define GPIO_SMEM_MAX_PC_INTERRUPTS	8
-
-struct tramp_gpio_save {
-	unsigned int enable;
-	unsigned int detect;
-	unsigned int polarity;
-};
-
-struct tramp_gpio_smem {
-	uint16_t num_fired[GPIO_SMEM_NUM_GROUPS];
-	uint16_t fired[GPIO_SMEM_NUM_GROUPS][GPIO_SMEM_MAX_PC_INTERRUPTS];
-	uint32_t enabled[NUM_GPIO_INT_REGISTERS];
-	uint32_t detection[NUM_GPIO_INT_REGISTERS];
-	uint32_t polarity[NUM_GPIO_INT_REGISTERS];
-};
-
-
-void smsm_print_sleep_info(void)
-{
-	unsigned long flags;
-	uint32_t *ptr;
-#ifndef CONFIG_ARCH_MSM_SCORPION
-	struct tramp_gpio_smem *gpio;
-	struct smsm_interrupt_info *int_info;
-#endif
-
-
-	spin_lock_irqsave(&smem_lock, flags);
-
-	ptr = smem_alloc(SMEM_SMSM_SLEEP_DELAY, sizeof(*ptr));
-	if (ptr)
-		pr_info("SMEM_SMSM_SLEEP_DELAY: %x\n", *ptr);
-
-	ptr = smem_alloc(SMEM_SMSM_LIMIT_SLEEP, sizeof(*ptr));
-	if (ptr)
-		pr_info("SMEM_SMSM_LIMIT_SLEEP: %x\n", *ptr);
-
-	ptr = smem_alloc(SMEM_SLEEP_POWER_COLLAPSE_DISABLED, sizeof(*ptr));
-	if (ptr)
-		pr_info("SMEM_SLEEP_POWER_COLLAPSE_DISABLED: %x\n", *ptr);
-
-#ifndef CONFIG_ARCH_MSM_SCORPION
-	int_info = smem_alloc(SMEM_SMSM_INT_INFO, sizeof(*int_info));
-	if (int_info)
-		pr_info("SMEM_SMSM_INT_INFO %x %x %x\n",
-			int_info->interrupt_mask,
-			int_info->pending_interrupts,
-			int_info->wakeup_reason);
-
-	gpio = smem_alloc(SMEM_GPIO_INT, sizeof(*gpio));
-	if (gpio) {
-		int i;
-		for (i = 0; i < NUM_GPIO_INT_REGISTERS; i++)
-			pr_info("SMEM_GPIO_INT: %d: e %x d %x p %x\n",
-				i, gpio->enabled[i], gpio->detection[i],
-				gpio->polarity[i]);
-
-		for (i = 0; i < GPIO_SMEM_NUM_GROUPS; i++)
-			pr_info("SMEM_GPIO_INT: %d: f %d: %d %d...\n",
-				i, gpio->num_fired[i], gpio->fired[i][0],
-				gpio->fired[i][1]);
-	}
-#else
-#endif
-	spin_unlock_irqrestore(&smem_lock, flags);
-}
-
diff --git a/arch/arm/mach-msm/smd_private.h b/arch/arm/mach-msm/smd_private.h
deleted file mode 100644
index 727bfe6..0000000
--- a/arch/arm/mach-msm/smd_private.h
+++ /dev/null
@@ -1,403 +0,0 @@
-/* arch/arm/mach-msm/smd_private.h
- *
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2007 QUALCOMM Incorporated
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-#ifndef _ARCH_ARM_MACH_MSM_MSM_SMD_PRIVATE_H_
-#define _ARCH_ARM_MACH_MSM_MSM_SMD_PRIVATE_H_
-
-#include <linux/platform_device.h>
-#include <linux/spinlock.h>
-#include <linux/list.h>
-#include <linux/io.h>
-
-#include <mach/msm_iomap.h>
-
-struct smem_heap_info {
-	unsigned initialized;
-	unsigned free_offset;
-	unsigned heap_remaining;
-	unsigned reserved;
-};
-
-struct smem_heap_entry {
-	unsigned allocated;
-	unsigned offset;
-	unsigned size;
-	unsigned reserved;
-};
-
-struct smem_proc_comm {
-	unsigned command;
-	unsigned status;
-	unsigned data1;
-	unsigned data2;
-};
-
-#define PC_APPS  0
-#define PC_MODEM 1
-
-#define VERSION_SMD       0
-#define VERSION_QDSP6     4
-#define VERSION_APPS_SBL  6
-#define VERSION_MODEM_SBL 7
-#define VERSION_APPS      8
-#define VERSION_MODEM     9
-
-struct smem_shared {
-	struct smem_proc_comm proc_comm[4];
-	unsigned version[32];
-	struct smem_heap_info heap_info;
-	struct smem_heap_entry heap_toc[512];
-};
-
-#define SMSM_V1_SIZE		(sizeof(unsigned) * 8)
-#define SMSM_V2_SIZE		(sizeof(unsigned) * 4)
-
-#ifdef CONFIG_MSM_SMD_PKG3
-struct smsm_interrupt_info {
-	uint32_t interrupt_mask;
-	uint32_t pending_interrupts;
-	uint32_t wakeup_reason;
-};
-#else
-#define DEM_MAX_PORT_NAME_LEN (20)
-struct msm_dem_slave_data {
-	uint32_t sleep_time;
-	uint32_t interrupt_mask;
-	uint32_t resources_used;
-	uint32_t reserved1;
-
-	uint32_t wakeup_reason;
-	uint32_t pending_interrupts;
-	uint32_t rpc_prog;
-	uint32_t rpc_proc;
-	char     smd_port_name[DEM_MAX_PORT_NAME_LEN];
-	uint32_t reserved2;
-};
-#endif
-
-#define SZ_DIAG_ERR_MSG 0xC8
-#define ID_DIAG_ERR_MSG SMEM_DIAG_ERR_MESSAGE
-#define ID_SMD_CHANNELS SMEM_SMD_BASE_ID
-#define ID_SHARED_STATE SMEM_SMSM_SHARED_STATE
-#define ID_CH_ALLOC_TBL SMEM_CHANNEL_ALLOC_TBL
-
-#define SMSM_INIT		0x00000001
-#define SMSM_SMDINIT		0x00000008
-#define SMSM_RPCINIT		0x00000020
-#define SMSM_RESET		0x00000040
-#define SMSM_RSA		0x00000080
-#define SMSM_RUN		0x00000100
-#define SMSM_PWRC		0x00000200
-#define SMSM_TIMEWAIT		0x00000400
-#define SMSM_TIMEINIT		0x00000800
-#define SMSM_PWRC_EARLY_EXIT	0x00001000
-#define SMSM_WFPI		0x00002000
-#define SMSM_SLEEP		0x00004000
-#define SMSM_SLEEPEXIT		0x00008000
-#define SMSM_APPS_REBOOT	0x00020000
-#define SMSM_SYSTEM_POWER_DOWN	0x00040000
-#define SMSM_SYSTEM_REBOOT	0x00080000
-#define SMSM_SYSTEM_DOWNLOAD	0x00100000
-#define SMSM_PWRC_SUSPEND	0x00200000
-#define SMSM_APPS_SHUTDOWN	0x00400000
-#define SMSM_SMD_LOOPBACK	0x00800000
-#define SMSM_RUN_QUIET		0x01000000
-#define SMSM_MODEM_WAIT		0x02000000
-#define SMSM_MODEM_BREAK	0x04000000
-#define SMSM_MODEM_CONTINUE	0x08000000
-#define SMSM_UNKNOWN		0x80000000
-
-#define SMSM_WKUP_REASON_RPC	0x00000001
-#define SMSM_WKUP_REASON_INT	0x00000002
-#define SMSM_WKUP_REASON_GPIO	0x00000004
-#define SMSM_WKUP_REASON_TIMER	0x00000008
-#define SMSM_WKUP_REASON_ALARM	0x00000010
-#define SMSM_WKUP_REASON_RESET	0x00000020
-
-#ifdef CONFIG_ARCH_MSM7X00A
-enum smsm_state_item {
-	SMSM_STATE_APPS = 1,
-	SMSM_STATE_MODEM = 3,
-	SMSM_STATE_COUNT,
-};
-#else
-enum smsm_state_item {
-	SMSM_STATE_APPS,
-	SMSM_STATE_MODEM,
-	SMSM_STATE_HEXAGON,
-	SMSM_STATE_APPS_DEM,
-	SMSM_STATE_MODEM_DEM,
-	SMSM_STATE_QDSP6_DEM,
-	SMSM_STATE_POWER_MASTER_DEM,
-	SMSM_STATE_TIME_MASTER_DEM,
-	SMSM_STATE_COUNT,
-};
-#endif
-
-void *smem_alloc(unsigned id, unsigned size);
-int smsm_change_state(enum smsm_state_item item, uint32_t clear_mask, uint32_t set_mask);
-uint32_t smsm_get_state(enum smsm_state_item item);
-int smsm_set_sleep_duration(uint32_t delay);
-void smsm_print_sleep_info(void);
-
-#define SMEM_NUM_SMD_CHANNELS        64
-
-typedef enum {
-	/* fixed items */
-	SMEM_PROC_COMM = 0,
-	SMEM_HEAP_INFO,
-	SMEM_ALLOCATION_TABLE,
-	SMEM_VERSION_INFO,
-	SMEM_HW_RESET_DETECT,
-	SMEM_AARM_WARM_BOOT,
-	SMEM_DIAG_ERR_MESSAGE,
-	SMEM_SPINLOCK_ARRAY,
-	SMEM_MEMORY_BARRIER_LOCATION,
-
-	/* dynamic items */
-	SMEM_AARM_PARTITION_TABLE,
-	SMEM_AARM_BAD_BLOCK_TABLE,
-	SMEM_RESERVE_BAD_BLOCKS,
-	SMEM_WM_UUID,
-	SMEM_CHANNEL_ALLOC_TBL,
-	SMEM_SMD_BASE_ID,
-	SMEM_SMEM_LOG_IDX = SMEM_SMD_BASE_ID + SMEM_NUM_SMD_CHANNELS,
-	SMEM_SMEM_LOG_EVENTS,
-	SMEM_SMEM_STATIC_LOG_IDX,
-	SMEM_SMEM_STATIC_LOG_EVENTS,
-	SMEM_SMEM_SLOW_CLOCK_SYNC,
-	SMEM_SMEM_SLOW_CLOCK_VALUE,
-	SMEM_BIO_LED_BUF,
-	SMEM_SMSM_SHARED_STATE,
-	SMEM_SMSM_INT_INFO,
-	SMEM_SMSM_SLEEP_DELAY,
-	SMEM_SMSM_LIMIT_SLEEP,
-	SMEM_SLEEP_POWER_COLLAPSE_DISABLED,
-	SMEM_KEYPAD_KEYS_PRESSED,
-	SMEM_KEYPAD_STATE_UPDATED,
-	SMEM_KEYPAD_STATE_IDX,
-	SMEM_GPIO_INT,
-	SMEM_MDDI_LCD_IDX,
-	SMEM_MDDI_HOST_DRIVER_STATE,
-	SMEM_MDDI_LCD_DISP_STATE,
-	SMEM_LCD_CUR_PANEL,
-	SMEM_MARM_BOOT_SEGMENT_INFO,
-	SMEM_AARM_BOOT_SEGMENT_INFO,
-	SMEM_SLEEP_STATIC,
-	SMEM_SCORPION_FREQUENCY,
-	SMEM_SMD_PROFILES,
-	SMEM_TSSC_BUSY,
-	SMEM_HS_SUSPEND_FILTER_INFO,
-	SMEM_BATT_INFO,
-	SMEM_APPS_BOOT_MODE,
-	SMEM_VERSION_FIRST,
-	SMEM_VERSION_LAST = SMEM_VERSION_FIRST + 24,
-	SMEM_OSS_RRCASN1_BUF1,
-	SMEM_OSS_RRCASN1_BUF2,
-	SMEM_ID_VENDOR0,
-	SMEM_ID_VENDOR1,
-	SMEM_ID_VENDOR2,
-	SMEM_HW_SW_BUILD_ID,
-	SMEM_SMD_BLOCK_PORT_BASE_ID,
-	SMEM_SMD_BLOCK_PORT_PROC0_HEAP = SMEM_SMD_BLOCK_PORT_BASE_ID + SMEM_NUM_SMD_CHANNELS,
-	SMEM_SMD_BLOCK_PORT_PROC1_HEAP = SMEM_SMD_BLOCK_PORT_PROC0_HEAP + SMEM_NUM_SMD_CHANNELS,
-	SMEM_I2C_MUTEX = SMEM_SMD_BLOCK_PORT_PROC1_HEAP + SMEM_NUM_SMD_CHANNELS,
-	SMEM_SCLK_CONVERSION,
-	SMEM_SMD_SMSM_INTR_MUX,
-	SMEM_SMSM_CPU_INTR_MASK,
-	SMEM_APPS_DEM_SLAVE_DATA,
-	SMEM_QDSP6_DEM_SLAVE_DATA,
-	SMEM_CLKREGIM_BSP,
-	SMEM_CLKREGIM_SOURCES,
-	SMEM_SMD_FIFO_BASE_ID,
-	SMEM_USABLE_RAM_PARTITION_TABLE = SMEM_SMD_FIFO_BASE_ID + SMEM_NUM_SMD_CHANNELS,
-	SMEM_POWER_ON_STATUS_INFO,
-	SMEM_DAL_AREA,
-	SMEM_SMEM_LOG_POWER_IDX,
-	SMEM_SMEM_LOG_POWER_WRAP,
-	SMEM_SMEM_LOG_POWER_EVENTS,
-	SMEM_ERR_CRASH_LOG,
-	SMEM_ERR_F3_TRACE_LOG,
-	SMEM_NUM_ITEMS,
-} smem_mem_type;
-
-
-#define SMD_SS_CLOSED		0x00000000
-#define SMD_SS_OPENING		0x00000001
-#define SMD_SS_OPENED		0x00000002
-#define SMD_SS_FLUSHING		0x00000003
-#define SMD_SS_CLOSING		0x00000004
-#define SMD_SS_RESET		0x00000005
-#define SMD_SS_RESET_OPENING	0x00000006
-
-#define SMD_BUF_SIZE		8192
-#define SMD_CHANNELS		64
-
-#define SMD_HEADER_SIZE		20
-
-struct smd_alloc_elm {
-	char name[20];
-	uint32_t cid;
-	uint32_t ctype;
-	uint32_t ref_count;
-};
-
-struct smd_half_channel {
-	unsigned state;
-	unsigned char fDSR;
-	unsigned char fCTS;
-	unsigned char fCD;
-	unsigned char fRI;
-	unsigned char fHEAD;
-	unsigned char fTAIL;
-	unsigned char fSTATE;
-	unsigned char fUNUSED;
-	unsigned tail;
-	unsigned head;
-} __attribute__(( aligned(4), packed ));
-
-/* Only used on SMD package v3 on msm7201a */
-struct smd_shared_v1 {
-	struct smd_half_channel ch0;
-	unsigned char data0[SMD_BUF_SIZE];
-	struct smd_half_channel ch1;
-	unsigned char data1[SMD_BUF_SIZE];
-};
-
-/* Used on SMD package v4 */
-struct smd_shared_v2 {
-	struct smd_half_channel ch0;
-	struct smd_half_channel ch1;
-};
-
-struct smd_channel {
-	volatile struct smd_half_channel *send;
-	volatile struct smd_half_channel *recv;
-	unsigned char *send_data;
-	unsigned char *recv_data;
-
-	unsigned fifo_mask;
-	unsigned fifo_size;
-	unsigned current_packet;
-	unsigned n;
-
-	struct list_head ch_list;
-
-	void *priv;
-	void (*notify)(void *priv, unsigned flags);
-
-	int (*read)(struct smd_channel *ch, void *data, int len);
-	int (*write)(struct smd_channel *ch, const void *data, int len);
-	int (*read_avail)(struct smd_channel *ch);
-	int (*write_avail)(struct smd_channel *ch);
-
-	void (*update_state)(struct smd_channel *ch);
-	unsigned last_state;
-	void (*notify_other_cpu)(void);
-	unsigned type;
-
-	char name[32];
-	struct platform_device pdev;
-};
-
-#define SMD_TYPE_MASK		0x0FF
-#define SMD_TYPE_APPS_MODEM	0x000
-#define SMD_TYPE_APPS_DSP	0x001
-#define SMD_TYPE_MODEM_DSP	0x002
-
-#define SMD_KIND_MASK		0xF00
-#define SMD_KIND_UNKNOWN	0x000
-#define SMD_KIND_STREAM		0x100
-#define SMD_KIND_PACKET		0x200
-
-extern struct list_head smd_ch_closed_list;
-extern struct list_head smd_ch_list_modem;
-extern struct list_head smd_ch_list_dsp;
-
-extern spinlock_t smd_lock;
-extern spinlock_t smem_lock;
-
-void *smem_find(unsigned id, unsigned size);
-void *smem_item(unsigned id, unsigned *size);
-uint32_t raw_smsm_get_state(enum smsm_state_item item);
-
-extern void msm_init_last_radio_log(struct module *);
-
-#ifdef CONFIG_MSM_SMD_PKG3
-/*
- * This allocator assumes an SMD Package v3 which only exists on
- * MSM7x00 SoC's.
- */
-static inline int _smd_alloc_channel(struct smd_channel *ch)
-{
-	struct smd_shared_v1 *shared1;
-
-	shared1 = smem_alloc(ID_SMD_CHANNELS + ch->n, sizeof(*shared1));
-	if (!shared1) {
-		pr_err("smd_alloc_channel() cid %d does not exist\n", ch->n);
-		return -1;
-	}
-	ch->send = &shared1->ch0;
-	ch->recv = &shared1->ch1;
-	ch->send_data = shared1->data0;
-	ch->recv_data = shared1->data1;
-	ch->fifo_size = SMD_BUF_SIZE;
-	return 0;
-}
-#else
-/*
- * This allocator assumes an SMD Package v4, the most common
- * and the default.
- */
-static inline int _smd_alloc_channel(struct smd_channel *ch)
-{
-	struct smd_shared_v2 *shared2;
-	void *buffer;
-	unsigned buffer_sz;
-
-	shared2 = smem_alloc(SMEM_SMD_BASE_ID + ch->n, sizeof(*shared2));
-	buffer = smem_item(SMEM_SMD_FIFO_BASE_ID + ch->n, &buffer_sz);
-
-	if (!buffer)
-		return -1;
-
-	/* buffer must be a power-of-two size */
-	if (buffer_sz & (buffer_sz - 1))
-		return -1;
-
-	buffer_sz /= 2;
-	ch->send = &shared2->ch0;
-	ch->recv = &shared2->ch1;
-	ch->send_data = buffer;
-	ch->recv_data = buffer + buffer_sz;
-	ch->fifo_size = buffer_sz;
-	return 0;
-}
-#endif /* CONFIG_MSM_SMD_PKG3 */
-
-#if defined(CONFIG_ARCH_MSM7X30)
-static inline void msm_a2m_int(uint32_t irq)
-{
-	writel(1 << irq, MSM_GCC_BASE + 0x8);
-}
-#else
-static inline void msm_a2m_int(uint32_t irq)
-{
-	writel(1, MSM_CSR_BASE + 0x400 + (irq * 4));
-}
-#endif /* CONFIG_ARCH_MSM7X30 */
-
-
-#endif
diff --git a/arch/arm/mach-msm/vreg.c b/arch/arm/mach-msm/vreg.c
deleted file mode 100644
index bd66ed0..0000000
--- a/arch/arm/mach-msm/vreg.c
+++ /dev/null
@@ -1,220 +0,0 @@
-/* arch/arm/mach-msm/vreg.c
- *
- * Copyright (C) 2008 Google, Inc.
- * Copyright (c) 2009, Code Aurora Forum. All rights reserved.
- * Author: Brian Swetland <swetland@google.com>
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/device.h>
-#include <linux/init.h>
-#include <linux/debugfs.h>
-#include <linux/module.h>
-#include <linux/string.h>
-#include <mach/vreg.h>
-
-#include "proc_comm.h"
-
-struct vreg {
-	const char *name;
-	unsigned id;
-	int status;
-	unsigned refcnt;
-};
-
-#define VREG(_name, _id, _status, _refcnt) \
-	{ .name = _name, .id = _id, .status = _status, .refcnt = _refcnt }
-
-static struct vreg vregs[] = {
-	VREG("msma",	0, 0, 0),
-	VREG("msmp",	1, 0, 0),
-	VREG("msme1",	2, 0, 0),
-	VREG("msmc1",	3, 0, 0),
-	VREG("msmc2",	4, 0, 0),
-	VREG("gp3",	5, 0, 0),
-	VREG("msme2",	6, 0, 0),
-	VREG("gp4",	7, 0, 0),
-	VREG("gp1",	8, 0, 0),
-	VREG("tcxo",	9, 0, 0),
-	VREG("pa",	10, 0, 0),
-	VREG("rftx",	11, 0, 0),
-	VREG("rfrx1",	12, 0, 0),
-	VREG("rfrx2",	13, 0, 0),
-	VREG("synt",	14, 0, 0),
-	VREG("wlan",	15, 0, 0),
-	VREG("usb",	16, 0, 0),
-	VREG("boost",	17, 0, 0),
-	VREG("mmc",	18, 0, 0),
-	VREG("ruim",	19, 0, 0),
-	VREG("msmc0",	20, 0, 0),
-	VREG("gp2",	21, 0, 0),
-	VREG("gp5",	22, 0, 0),
-	VREG("gp6",	23, 0, 0),
-	VREG("rf",	24, 0, 0),
-	VREG("rf_vco",	26, 0, 0),
-	VREG("mpll",	27, 0, 0),
-	VREG("s2",	28, 0, 0),
-	VREG("s3",	29, 0, 0),
-	VREG("rfubm",	30, 0, 0),
-	VREG("ncp",	31, 0, 0),
-	VREG("gp7",	32, 0, 0),
-	VREG("gp8",	33, 0, 0),
-	VREG("gp9",	34, 0, 0),
-	VREG("gp10",	35, 0, 0),
-	VREG("gp11",	36, 0, 0),
-	VREG("gp12",	37, 0, 0),
-	VREG("gp13",	38, 0, 0),
-	VREG("gp14",	39, 0, 0),
-	VREG("gp15",	40, 0, 0),
-	VREG("gp16",	41, 0, 0),
-	VREG("gp17",	42, 0, 0),
-	VREG("s4",	43, 0, 0),
-	VREG("usb2",	44, 0, 0),
-	VREG("wlan2",	45, 0, 0),
-	VREG("xo_out",	46, 0, 0),
-	VREG("lvsw0",	47, 0, 0),
-	VREG("lvsw1",	48, 0, 0),
-};
-
-struct vreg *vreg_get(struct device *dev, const char *id)
-{
-	int n;
-	for (n = 0; n < ARRAY_SIZE(vregs); n++) {
-		if (!strcmp(vregs[n].name, id))
-			return vregs + n;
-	}
-	return ERR_PTR(-ENOENT);
-}
-
-void vreg_put(struct vreg *vreg)
-{
-}
-
-int vreg_enable(struct vreg *vreg)
-{
-	unsigned id = vreg->id;
-	unsigned enable = 1;
-
-	if (vreg->refcnt == 0)
-		vreg->status = msm_proc_comm(PCOM_VREG_SWITCH, &id, &enable);
-
-	if ((vreg->refcnt < UINT_MAX) && (!vreg->status))
-		vreg->refcnt++;
-
-	return vreg->status;
-}
-
-int vreg_disable(struct vreg *vreg)
-{
-	unsigned id = vreg->id;
-	unsigned enable = 0;
-
-	if (!vreg->refcnt)
-		return 0;
-
-	if (vreg->refcnt == 1)
-		vreg->status = msm_proc_comm(PCOM_VREG_SWITCH, &id, &enable);
-
-	if (!vreg->status)
-		vreg->refcnt--;
-
-	return vreg->status;
-}
-
-int vreg_set_level(struct vreg *vreg, unsigned mv)
-{
-	unsigned id = vreg->id;
-
-	vreg->status = msm_proc_comm(PCOM_VREG_SET_LEVEL, &id, &mv);
-	return vreg->status;
-}
-
-#if defined(CONFIG_DEBUG_FS)
-
-static int vreg_debug_set(void *data, u64 val)
-{
-	struct vreg *vreg = data;
-	switch (val) {
-	case 0:
-		vreg_disable(vreg);
-		break;
-	case 1:
-		vreg_enable(vreg);
-		break;
-	default:
-		vreg_set_level(vreg, val);
-		break;
-	}
-	return 0;
-}
-
-static int vreg_debug_get(void *data, u64 *val)
-{
-	struct vreg *vreg = data;
-
-	if (!vreg->status)
-		*val = 0;
-	else
-		*val = 1;
-
-	return 0;
-}
-
-static int vreg_debug_count_set(void *data, u64 val)
-{
-	struct vreg *vreg = data;
-	if (val > UINT_MAX)
-		val = UINT_MAX;
-	vreg->refcnt = val;
-	return 0;
-}
-
-static int vreg_debug_count_get(void *data, u64 *val)
-{
-	struct vreg *vreg = data;
-
-	*val = vreg->refcnt;
-
-	return 0;
-}
-
-DEFINE_SIMPLE_ATTRIBUTE(vreg_fops, vreg_debug_get, vreg_debug_set, "%llu\n");
-DEFINE_SIMPLE_ATTRIBUTE(vreg_count_fops, vreg_debug_count_get,
-			vreg_debug_count_set, "%llu\n");
-
-static int __init vreg_debug_init(void)
-{
-	struct dentry *dent;
-	int n;
-	char name[32];
-	const char *refcnt_name = "_refcnt";
-
-	dent = debugfs_create_dir("vreg", 0);
-	if (IS_ERR(dent))
-		return 0;
-
-	for (n = 0; n < ARRAY_SIZE(vregs); n++) {
-		(void) debugfs_create_file(vregs[n].name, 0644,
-					   dent, vregs + n, &vreg_fops);
-
-		strlcpy(name, vregs[n].name, sizeof(name));
-		strlcat(name, refcnt_name, sizeof(name));
-		(void) debugfs_create_file(name, 0644,
-					   dent, vregs + n, &vreg_count_fops);
-	}
-
-	return 0;
-}
-
-device_initcall(vreg_debug_init);
-#endif
diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
index 89a139e..31b66f2 100644
--- a/arch/arm/mach-mvebu/board-v7.c
+++ b/arch/arm/mach-mvebu/board-v7.c
@@ -184,7 +184,7 @@
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-static const char * const armada_370_xp_dt_compat[] = {
+static const char * const armada_370_xp_dt_compat[] __initconst = {
 	"marvell,armada-370-xp",
 	NULL,
 };
@@ -205,7 +205,7 @@
 	.dt_compat	= armada_370_xp_dt_compat,
 MACHINE_END
 
-static const char * const armada_375_dt_compat[] = {
+static const char * const armada_375_dt_compat[] __initconst = {
 	"marvell,armada375",
 	NULL,
 };
@@ -219,7 +219,7 @@
 	.dt_compat	= armada_375_dt_compat,
 MACHINE_END
 
-static const char * const armada_38x_dt_compat[] = {
+static const char * const armada_38x_dt_compat[] __initconst = {
 	"marvell,armada380",
 	"marvell,armada385",
 	NULL,
diff --git a/arch/arm/mach-mvebu/dove.c b/arch/arm/mach-mvebu/dove.c
index b50464e..5a17415 100644
--- a/arch/arm/mach-mvebu/dove.c
+++ b/arch/arm/mach-mvebu/dove.c
@@ -27,7 +27,7 @@
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-static const char * const dove_dt_compat[] = {
+static const char * const dove_dt_compat[] __initconst = {
 	"marvell,dove",
 	NULL
 };
diff --git a/arch/arm/mach-mvebu/kirkwood.c b/arch/arm/mach-mvebu/kirkwood.c
index 6b53108..925f75f 100644
--- a/arch/arm/mach-mvebu/kirkwood.c
+++ b/arch/arm/mach-mvebu/kirkwood.c
@@ -186,7 +186,7 @@
 	of_platform_populate(NULL, of_default_bus_match_table, auxdata, NULL);
 }
 
-static const char * const kirkwood_dt_board_compat[] = {
+static const char * const kirkwood_dt_board_compat[] __initconst = {
 	"marvell,kirkwood",
 	NULL
 };
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 1041b19..3e4b4ae 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -176,12 +176,6 @@
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_DEVKIT8000
-	bool "DEVKIT8000 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CUS
-
 config MACH_OMAP_LDP
 	bool "OMAP3 LDP board"
 	depends on ARCH_OMAP3
@@ -226,12 +220,6 @@
 	select OMAP_PACKAGE_CBB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
-config MACH_TOUCHBOOK
-	bool "OMAP3 Touch Book"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_NOKIA_N810
        bool
 
@@ -261,12 +249,6 @@
 config MACH_CM_T3730
        bool
 
-config MACH_SBC3530
-	bool "OMAP3 SBC STALKER board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CUS
-
 config OMAP3_SDRC_AC_TIMING
 	bool "Enable SDRC AC timing register changes"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b83f18f..ec002bd 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -243,7 +243,6 @@
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
-obj-$(CONFIG_MACH_DEVKIT8000)     	+= board-devkit8000.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
@@ -254,9 +253,6 @@
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
-obj-$(CONFIG_MACH_TOUCHBOOK)		+= board-omap3touchbook.o
-
-obj-$(CONFIG_MACH_SBC3530)		+= board-omap3stalker.o
 
 # Platform specific device init code
 
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
deleted file mode 100644
index d8e4f34..0000000
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ /dev/null
@@ -1,654 +0,0 @@
-/*
- * board-devkit8000.c - TimLL Devkit8000
- *
- * Copyright (C) 2009 Kim Botherway
- * Copyright (C) 2010 Thomas Weber
- *
- * Modified from mach-omap2/board-omap3beagle.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include "id.h"
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/dm9000.h>
-#include <linux/interrupt.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define	NAND_CS			0
-
-#define OMAP_DM9000_GPIO_IRQ	25
-#define OMAP3_DEVKIT_TS_GPIO	27
-
-static struct mtd_partition devkit8000_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader",
-		.offset		= 0,
-		.size		= 4 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot Env",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size		= 1 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "File System",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= 29,
-		.deferred	= true,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply devkit8000_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supply[] = {
-	REGULATOR_SUPPLY("vcc", "spi2.0"),
-};
-
-static const struct display_timing devkit8000_lcd_videomode = {
-	.pixelclock	= { 0, 40000000, 0 },
-
-	.hactive = { 0, 800, 0 },
-	.hfront_porch = { 0, 1, 0 },
-	.hback_porch = { 0, 1, 0 },
-	.hsync_len = { 0, 48, 0 },
-
-	.vactive = { 0, 480, 0 },
-	.vfront_porch = { 0, 12, 0 },
-	.vback_porch = { 0, 25, 0 },
-	.vsync_len = { 0, 3, 0 },
-
-	.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
-		DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
-};
-
-static struct panel_dpi_platform_data devkit8000_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 24,
-
-	.display_timing		= &devkit8000_lcd_videomode,
-
-	.enable_gpio		= -1,	/* filled in code */
-	.backlight_gpio		= -1,
-};
-
-static struct platform_device devkit8000_lcd_device = {
-	.name                   = "panel-dpi",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data devkit8000_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = 1,
-};
-
-static struct platform_device devkit8000_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data devkit8000_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = -1,	/* filled in code */
-};
-
-static struct platform_device devkit8000_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data devkit8000_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device devkit8000_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &devkit8000_tv_pdata,
-};
-
-static struct omap_dss_board_info devkit8000_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_1),
-	KEY(1, 0, KEY_2),
-	KEY(2, 0, KEY_3),
-	KEY(0, 1, KEY_4),
-	KEY(1, 1, KEY_5),
-	KEY(2, 1, KEY_6),
-	KEY(3, 1, KEY_F5),
-	KEY(0, 2, KEY_7),
-	KEY(1, 2, KEY_8),
-	KEY(2, 2, KEY_9),
-	KEY(3, 2, KEY_F6),
-	KEY(0, 3, KEY_F7),
-	KEY(1, 3, KEY_0),
-	KEY(2, 3, KEY_F8),
-	PERSISTENT_KEY(4, 5),
-	KEY(4, 4, KEY_VOLUMEUP),
-	KEY(5, 5, KEY_VOLUMEDOWN),
-	0
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data devkit8000_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 6,
-	.cols		= 6,
-	.rep		= 1,
-};
-
-static struct gpio_led gpio_leds[];
-
-static int devkit8000_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
-	/* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
-	devkit8000_lcd_pdata.enable_gpio = gpio + TWL4030_GPIO_MAX + 0;
-
-	/* gpio + 7 is "DVI_PD" (out, active low) */
-	devkit8000_tfp410_pdata.power_down_gpio = gpio + 7;
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
-	.use_leds	= true,
-	.pulldowns	= BIT(1) | BIT(2) | BIT(6) | BIT(8) | BIT(13)
-				| BIT(15) | BIT(16) | BIT(17),
-	.setup		= devkit8000_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data devkit8000_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vmmc1_supply),
-	.consumer_supplies	= devkit8000_vmmc1_supply,
-};
-
-/* VPLL1 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll1 = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
-	.consumer_supplies	= devkit8000_vpll1_supplies,
-};
-
-/* VAUX4 for ads7846 and nubs */
-static struct regulator_init_data devkit8000_vio = {
-	.constraints = {
-		.min_uV                 = 1800000,
-		.max_uV                 = 1800000,
-		.apply_uV               = true,
-		.valid_modes_mask       = REGULATOR_MODE_NORMAL
-			| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask         = REGULATOR_CHANGE_MODE
-			| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supply),
-	.consumer_supplies      = devkit8000_vio_supply,
-};
-
-static struct twl4030_platform_data devkit8000_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &devkit8000_gpio_data,
-	.vmmc1		= &devkit8000_vmmc1,
-	.vpll1		= &devkit8000_vpll1,
-	.vio		= &devkit8000_vio,
-	.keypad		= &devkit8000_kp_data,
-};
-
-static int __init devkit8000_i2c_init(void)
-{
-	omap3_pmic_get_config(&devkit8000_twldata,
-			  TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
-			  TWL_COMMON_REGULATOR_VDAC);
-	omap3_pmic_init("tps65930", &devkit8000_twldata);
-	/* Bus 3 is attached to the DVI port where devices like the pico DLP
-	 * projector don't work reliably with 400kHz */
-	omap_register_i2c_bus(3, 400, NULL, 0);
-	return 0;
-}
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "led1",
-		.default_trigger	= "heartbeat",
-		.gpio			= 186,
-		.active_low		= true,
-	},
-	{
-		.name			= "led2",
-		.default_trigger	= "mmc0",
-		.gpio			= 163,
-		.active_low		= true,
-	},
-	{
-		.name			= "ledB",
-		.default_trigger	= "none",
-		.gpio			= 153,
-		.active_low             = true,
-	},
-	{
-		.name			= "led3",
-		.default_trigger	= "none",
-		.gpio			= 164,
-		.active_low             = true,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-		.code			= BTN_EXTRA,
-		.gpio			= 26,
-		.desc			= "user",
-		.wakeup			= 1,
-	},
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-#define OMAP_DM9000_BASE	0x2c000000
-
-static struct resource omap_dm9000_resources[] = {
-	[0] = {
-		.start		= OMAP_DM9000_BASE,
-		.end		= (OMAP_DM9000_BASE + 0x4 - 1),
-		.flags		= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start		= (OMAP_DM9000_BASE + 0x400),
-		.end		= (OMAP_DM9000_BASE + 0x400 + 0x4 - 1),
-		.flags		= IORESOURCE_MEM,
-	},
-	[2] = {
-		.flags		= IORESOURCE_IRQ | IRQF_TRIGGER_LOW,
-	},
-};
-
-static struct dm9000_plat_data omap_dm9000_platdata = {
-	.flags = DM9000_PLATF_16BITONLY,
-};
-
-static struct platform_device omap_dm9000_dev = {
-	.name = "dm9000",
-	.id = -1,
-	.num_resources	= ARRAY_SIZE(omap_dm9000_resources),
-	.resource	= omap_dm9000_resources,
-	.dev = {
-		.platform_data = &omap_dm9000_platdata,
-	},
-};
-
-static void __init omap_dm9000_init(void)
-{
-	unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
-	struct omap_die_id odi;
-	int ret;
-
-	ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
-	if (ret < 0) {
-		printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
-			OMAP_DM9000_GPIO_IRQ);
-		return;
-	}
-
-	/* init the mac address using DIE id */
-	omap_get_die_id(&odi);
-
-	eth_addr[0] = 0x02; /* locally administered */
-	eth_addr[1] = odi.id_1 & 0xff;
-	eth_addr[2] = (odi.id_0 & 0xff000000) >> 24;
-	eth_addr[3] = (odi.id_0 & 0x00ff0000) >> 16;
-	eth_addr[4] = (odi.id_0 & 0x0000ff00) >> 8;
-	eth_addr[5] = (odi.id_0 & 0x000000ff);
-}
-
-static struct platform_device *devkit8000_devices[] __initdata = {
-	&leds_gpio,
-	&keys_gpio,
-	&omap_dm9000_dev,
-	&devkit8000_lcd_device,
-	&devkit8000_tfp410_device,
-	&devkit8000_dvi_connector_device,
-	&devkit8000_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* nCS and IRQ for Devkit8000 ethernet */
-	OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE0),
-	OMAP3_MUX(ETK_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
-	/* McSPI 2*/
-	OMAP3_MUX(MCSPI2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI2_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCSPI2_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI2_CS0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCSPI2_CS1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* PENDOWN GPIO */
-	OMAP3_MUX(ETK_D13, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
-	/* mUSB */
-	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* USB 1 */
-	OMAP3_MUX(ETK_CTL, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(ETK_D8, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D9, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D0, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D2, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D3, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D4, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D5, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D6, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-	OMAP3_MUX(ETK_D7, OMAP_MUX_MODE3 | OMAP_PIN_INPUT),
-
-	/* MMC 1 */
-	OMAP3_MUX(SDMMC1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(SDMMC1_DAT7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* McBSP 2 */
-	OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* I2C 1 */
-	OMAP3_MUX(I2C1_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C1_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 2 */
-	OMAP3_MUX(I2C2_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 3 */
-	OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* I2C 4 */
-	OMAP3_MUX(I2C4_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C4_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* serial ports */
-	OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* DSS */
-	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* expansion port */
-	/* McSPI 1 */
-	OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-	OMAP3_MUX(MCSPI1_CS3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
-	/* HDQ */
-	OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* McSPI4 */
-	OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
-	/* MMC 2 */
-	OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
-	/* I2C3 */
-	OMAP3_MUX(I2C3_SCL, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(I2C3_SDA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP_CLKS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	/* TPS IRQ */
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
-			OMAP_PIN_INPUT_PULLUP),
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init devkit8000_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-
-	omap_dm9000_init();
-
-	omap_hsmmc_init(mmc);
-	devkit8000_i2c_init();
-	omap_dm9000_resources[2].start = gpio_to_irq(OMAP_DM9000_GPIO_IRQ);
-	platform_add_devices(devkit8000_devices,
-			ARRAY_SIZE(devkit8000_devices));
-
-	omap_display_init(&devkit8000_dss_data);
-
-	omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	usbhs_init(&usbhs_bdata);
-	board_nand_init(devkit8000_nand_partitions,
-			ARRAY_SIZE(devkit8000_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-	omap_twl4030_audio_init("omap3beagle", NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(DEVKIT8000, "OMAP3 Devkit8000")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= devkit8000_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_secure_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
deleted file mode 100644
index 6311f4b..0000000
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Guangzhou EMA-Tech
- *
- * Modified from mach-omap2/board-omap3evm.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/spi/spi.h>
-#include <linux/interrupt.h>
-#include <linux/smsc911x.h>
-#include <linux/platform_data/at24.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-#define OMAP3STALKER_ETHR_START	0x2c000000
-#define OMAP3STALKER_ETHR_SIZE	1024
-#define OMAP3STALKER_ETHR_GPIO_IRQ	19
-#define OMAP3STALKER_SMC911X_CS	5
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
-	.cs             = OMAP3STALKER_SMC911X_CS,
-	.gpio_irq       = OMAP3STALKER_ETHR_GPIO_IRQ,
-	.gpio_reset     = -EINVAL,
-	.flags		= (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static inline void __init omap3stalker_init_eth(void)
-{
-	omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
-	gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3stalker_init_eth(void)
-{
-	return;
-}
-#endif
-
-/*
- * OMAP3 DSS control signals
- */
-
-#define DSS_ENABLE_GPIO	199
-#define LCD_PANEL_BKLIGHT_GPIO	210
-#define ENABLE_VPLL2_DEV_GRP	0xE0
-
-static void __init omap3_stalker_display_init(void)
-{
-	return;
-}
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = -1,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = DSS_ENABLE_GPIO,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3stalker_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_COMPOSITE,
-	.invert_polarity = false,
-};
-
-static struct platform_device omap3stalker_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_stalker_dss_data = {
-	.default_display_name = "dvi",
-};
-
-static struct regulator_consumer_supply omap3stalker_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3stalker_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3stalker_vmmc1 = {
-	.constraints		= {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vmmc1_supply),
-	.consumer_supplies	= omap3stalker_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3stalker_vsim = {
-	.constraints		= {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-		| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-		| REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3stalker_vsim_supply),
-	.consumer_supplies	= omap3stalker_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= 23,
-		.deferred	= true,
-	 },
-	{}			/* Terminator */
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-	 .code		= BTN_EXTRA,
-	 .gpio		= 18,
-	 .desc		= "user",
-	 .wakeup	= 1,
-	 },
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-static struct gpio_led gpio_leds[] = {
-	{
-	 .name			= "stalker:D8:usr0",
-	 .default_trigger	= "default-on",
-	 .gpio			= 126,
-	 },
-	{
-	 .name			= "stalker:D9:usr1",
-	 .default_trigger	= "default-on",
-	 .gpio			= 127,
-	 },
-	{
-	 .name			= "stalker:D3:mmc0",
-	 .gpio			= -EINVAL,	/* gets replaced */
-	 .active_low		= true,
-	 .default_trigger	= "mmc0",
-	 },
-	{
-	 .name			= "stalker:D4:heartbeat",
-	 .gpio			= -EINVAL,	/* gets replaced */
-	 .active_low		= true,
-	 .default_trigger	= "heartbeat",
-	 },
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static int
-omap3stalker_twl_gpio_setup(struct device *dev,
-			    unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/*
-	 * Most GPIOs are for USB OTG.  Some are mostly sent to
-	 * the P2 connector; notably LEDA for the LCD backlight.
-	 */
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
-			 "EN_LCD_BKL");
-
-	/* gpio + 7 == DVI Enable */
-	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
-	/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-	/* GPIO + 13 == ledsync (out, heartbeat) */
-	gpio_leds[3].gpio = gpio + 13;
-
-	platform_device_register(&leds_gpio);
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3stalker_gpio_data = {
-	.use_leds	= true,
-	.setup		= omap3stalker_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_LEFT),
-	KEY(0, 1, KEY_DOWN),
-	KEY(0, 2, KEY_ENTER),
-	KEY(0, 3, KEY_M),
-
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_UP),
-	KEY(1, 2, KEY_I),
-	KEY(1, 3, KEY_N),
-
-	KEY(2, 0, KEY_A),
-	KEY(2, 1, KEY_E),
-	KEY(2, 2, KEY_J),
-	KEY(2, 3, KEY_O),
-
-	KEY(3, 0, KEY_B),
-	KEY(3, 1, KEY_F),
-	KEY(3, 2, KEY_K),
-	KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap		= board_keymap,
-	.keymap_size	= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3stalker_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 4,
-	.cols		= 4,
-	.rep		= 1,
-};
-
-static struct twl4030_platform_data omap3stalker_twldata = {
-	/* platform_data for children goes here */
-	.keypad		= &omap3stalker_kp_data,
-	.gpio		= &omap3stalker_gpio_data,
-	.vmmc1		= &omap3stalker_vmmc1,
-	.vsim		= &omap3stalker_vsim,
-};
-
-static struct at24_platform_data fram_info = {
-	.byte_len	= (64 * 1024) / 8,
-	.page_size	= 8192,
-	.flags		= AT24_FLAG_ADDR16 | AT24_FLAG_IRUGO,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
-	{
-	 I2C_BOARD_INFO("24c64", 0x50),
-	 .flags		= I2C_CLIENT_WAKE,
-	 .platform_data	= &fram_info,
-	 },
-};
-
-static int __init omap3_stalker_i2c_init(void)
-{
-	omap3_pmic_get_config(&omap3stalker_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
-			TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	omap3stalker_twldata.vdac->constraints.apply_uV = true;
-	omap3stalker_twldata.vpll2->constraints.apply_uV = true;
-	omap3stalker_twldata.vpll2->constraints.name = "VDVI";
-
-	omap3_pmic_init("twl4030", &omap3stalker_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
-			      ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
-	return 0;
-}
-
-#define OMAP3_STALKER_TS_GPIO	175
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = 21,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct platform_device *omap3_stalker_devices[] __initdata = {
-	&keys_gpio,
-	&omap3stalker_tfp410_device,
-	&omap3stalker_dvi_connector_device,
-	&omap3stalker_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
-		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
-	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-		  OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
-	{.reg_offset = OMAP_MUX_TERMINATOR},
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3_stalker_init(void)
-{
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-
-	omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-	omap_hsmmc_init(mmc);
-
-	omap3_stalker_i2c_init();
-
-	platform_add_devices(omap3_stalker_devices,
-			     ARRAY_SIZE(omap3_stalker_devices));
-
-	omap_display_init(&omap3_stalker_dss_data);
-
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-	omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
-
-	omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
-	omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
-
-	omap3stalker_init_eth();
-	omap3_stalker_display_init();
-/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdr_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdr_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(SBC3530, "OMAP3 STALKER")
-	/* Maintainer: Jason Lam -lzg@ema-tech.com */
-	.atag_offset		= 0x100,
-	.map_io			= omap3_map_io,
-	.init_early		= omap35xx_init_early,
-	.init_irq		= omap3_init_irq,
-	.init_machine		= omap3_stalker_init,
-	.init_late		= omap35xx_init_late,
-	.init_time		= omap3_secure_sync32k_timer_init,
-	.restart		= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
deleted file mode 100644
index a01993e..0000000
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ /dev/null
@@ -1,395 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3touchbook.c
- *
- * Copyright (C) 2009 Always Innovating
- *
- * Modified from mach-omap2/board-omap3beagleboard.c
- *
- * Initial code: Grégoire Gentil, Tim Yamin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <linux/spi/spi.h>
-
-#include <linux/spi/ads7846.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-#include <asm/system_info.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#include <asm/setup.h>
-
-#define OMAP3_AC_GPIO		136
-#define OMAP3_TS_GPIO		162
-#define TB_BL_PWM_TIMER		9
-#define TB_KILL_POWER_GPIO	168
-
-#define	NAND_CS			0
-
-static unsigned long touchbook_revision;
-
-static struct mtd_partition omap3touchbook_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader",
-		.offset		= 0,
-		.size		= 4 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot Env",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size		= 1 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "Kernel",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name		= "File System",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-#include "sdram-micron-mt46h32m32lf-6.h"
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_wp	= 29,
-		.deferred	= true,
-	},
-	{}	/* Terminator */
-};
-
-static struct regulator_consumer_supply touchbook_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply touchbook_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct gpio_led gpio_leds[];
-
-static int touchbook_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* REVISIT: need ehci-omap hooks for external VBUS
-	 * power switch and overcurrent detect
-	 */
-	gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
-	gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
-			 "nEN_USB_PWR");
-
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data touchbook_gpio_data = {
-	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
-				| BIT(15) | BIT(16) | BIT(17),
-	.setup		= touchbook_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply touchbook_vdac_supply[] = {
-{
-	.supply		= "vdac",
-},
-};
-
-static struct regulator_consumer_supply touchbook_vdvi_supply[] = {
-{
-	.supply		= "vdvi",
-},
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data touchbook_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(touchbook_vmmc1_supply),
-	.consumer_supplies	= touchbook_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data touchbook_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(touchbook_vsim_supply),
-	.consumer_supplies	= touchbook_vsim_supply,
-};
-
-static struct twl4030_platform_data touchbook_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &touchbook_gpio_data,
-	.vmmc1		= &touchbook_vmmc1,
-	.vsim		= &touchbook_vsim,
-};
-
-static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
-	{
-		I2C_BOARD_INFO("bq27200", 0x55),
-	},
-};
-
-static int __init omap3_touchbook_i2c_init(void)
-{
-	/* Standard TouchBook bus */
-	omap3_pmic_get_config(&touchbook_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	touchbook_twldata.vdac->num_consumer_supplies =
-					ARRAY_SIZE(touchbook_vdac_supply);
-	touchbook_twldata.vdac->consumer_supplies = touchbook_vdac_supply;
-
-	touchbook_twldata.vpll2->constraints.name = "VDVI";
-	touchbook_twldata.vpll2->num_consumer_supplies =
-					ARRAY_SIZE(touchbook_vdvi_supply);
-	touchbook_twldata.vpll2->consumer_supplies = touchbook_vdvi_supply;
-
-	omap3_pmic_init("twl4030", &touchbook_twldata);
-	/* Additional TouchBook bus */
-	omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
-			ARRAY_SIZE(touchBook_i2c_boardinfo));
-
-	return 0;
-}
-
-static struct ads7846_platform_data ads7846_pdata = {
-	.x_min			= 100,
-	.y_min			= 265,
-	.x_max			= 3950,
-	.y_max			= 3750,
-	.x_plate_ohms		= 40,
-	.pressure_max		= 255,
-	.debounce_max		= 10,
-	.debounce_tol		= 5,
-	.debounce_rep		= 1,
-	.gpio_pendown		= OMAP3_TS_GPIO,
-	.keep_vref_on		= 1,
-};
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "touchbook::usr0",
-		.default_trigger	= "heartbeat",
-		.gpio			= 150,
-	},
-	{
-		.name			= "touchbook::usr1",
-		.default_trigger	= "mmc0",
-		.gpio			= 149,
-	},
-	{
-		.name			= "touchbook::pmu_stat",
-		.gpio			= -EINVAL,	/* gets replaced */
-		.active_low		= true,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-static struct gpio_keys_button gpio_buttons[] = {
-	{
-		.code			= BTN_EXTRA,
-		.gpio			= 7,
-		.desc			= "user",
-		.wakeup			= 1,
-	},
-	{
-		.code			= KEY_POWER,
-		.gpio			= 183,
-		.desc			= "power",
-		.wakeup			= 1,
-	},
-};
-
-static struct gpio_keys_platform_data gpio_key_info = {
-	.buttons	= gpio_buttons,
-	.nbuttons	= ARRAY_SIZE(gpio_buttons),
-};
-
-static struct platform_device keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_key_info,
-	},
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = 147,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct platform_device *omap3_touchbook_devices[] __initdata = {
-	&leds_gpio,
-	&keys_gpio,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void omap3_touchbook_poweroff(void)
-{
-	int pwr_off = TB_KILL_POWER_GPIO;
-
-	if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
-		printk(KERN_ERR "Unable to get kill power GPIO\n");
-}
-
-static int __init early_touchbook_revision(char *p)
-{
-	if (!p)
-		return 0;
-
-	return kstrtoul(p, 10, &touchbook_revision);
-}
-early_param("tbr", early_touchbook_revision);
-
-static void __init omap3_touchbook_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
-	pm_power_off = omap3_touchbook_poweroff;
-
-	if (system_rev >= 0x20 && system_rev <= 0x34301000) {
-		omap_mux_init_gpio(23, OMAP_PIN_INPUT);
-		mmc[0].gpio_wp = 23;
-	} else {
-		omap_mux_init_gpio(29, OMAP_PIN_INPUT);
-	}
-	omap_hsmmc_init(mmc);
-
-	omap3_touchbook_i2c_init();
-	platform_add_devices(omap3_touchbook_devices,
-			ARRAY_SIZE(omap3_touchbook_devices));
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
-	/* Touchscreen and accelerometer */
-	omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-	board_nand_init(omap3touchbook_nand_partitions,
-			ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(TOUCHBOOK, "OMAP3 touchbook Board")
-	/* Maintainer: Gregoire Gentil - http://www.alwaysinnovating.com */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3430_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3_touchbook_init,
-	.init_late	= omap3430_init_late,
-	.init_time	= omap3_secure_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-shmobile/Makefile b/arch/arm/mach-shmobile/Makefile
index d53996e..03794b0 100644
--- a/arch/arm/mach-shmobile/Makefile
+++ b/arch/arm/mach-shmobile/Makefile
@@ -12,8 +12,8 @@
 obj-$(CONFIG_ARCH_R8A7740)	+= setup-r8a7740.o pm-r8a7740.o
 obj-$(CONFIG_ARCH_R8A7778)	+= setup-r8a7778.o
 obj-$(CONFIG_ARCH_R8A7779)	+= setup-r8a7779.o pm-r8a7779.o
-obj-$(CONFIG_ARCH_R8A7790)	+= setup-r8a7790.o pm-r8a7790.o
-obj-$(CONFIG_ARCH_R8A7791)	+= setup-r8a7791.o pm-r8a7791.o
+obj-$(CONFIG_ARCH_R8A7790)	+= setup-r8a7790.o
+obj-$(CONFIG_ARCH_R8A7791)	+= setup-r8a7791.o
 obj-$(CONFIG_ARCH_R8A7794)	+= setup-r8a7794.o
 obj-$(CONFIG_ARCH_EMEV2)	+= setup-emev2.o
 obj-$(CONFIG_ARCH_R7S72100)	+= setup-r7s72100.o
@@ -46,10 +46,10 @@
 
 # PM objects
 obj-$(CONFIG_SUSPEND)		+= suspend.o
-obj-$(CONFIG_CPU_IDLE)		+= cpuidle.o
 obj-$(CONFIG_CPU_FREQ)		+= cpufreq.o
 obj-$(CONFIG_PM_RCAR)		+= pm-rcar.o
 obj-$(CONFIG_PM_RMOBILE)	+= pm-rmobile.o
+obj-$(CONFIG_ARCH_RCAR_GEN2)	+= pm-rcar-gen2.o
 
 # special sh7372 handling for IRQ objects and low level sleep code
 obj-$(CONFIG_ARCH_SH7372)	+= entry-intc.o sleep-sh7372.o
diff --git a/arch/arm/mach-shmobile/common.h b/arch/arm/mach-shmobile/common.h
index 309025e..1dc0971 100644
--- a/arch/arm/mach-shmobile/common.h
+++ b/arch/arm/mach-shmobile/common.h
@@ -23,8 +23,6 @@
 extern int shmobile_clk_init(void);
 extern void shmobile_handle_irq_intc(struct pt_regs *);
 extern struct platform_suspend_ops shmobile_suspend_ops;
-struct cpuidle_driver;
-extern void shmobile_cpuidle_set_driver(struct cpuidle_driver *drv);
 
 #ifdef CONFIG_SUSPEND
 int shmobile_suspend_init(void);
@@ -34,12 +32,6 @@
 static inline void shmobile_smp_apmu_suspend_init(void) { }
 #endif
 
-#ifdef CONFIG_CPU_IDLE
-int shmobile_cpuidle_init(void);
-#else
-static inline int shmobile_cpuidle_init(void) { return 0; }
-#endif
-
 #ifdef CONFIG_CPU_FREQ
 int shmobile_cpufreq_init(void);
 #else
@@ -51,7 +43,6 @@
 static inline void __init shmobile_init_late(void)
 {
 	shmobile_suspend_init();
-	shmobile_cpuidle_init();
 	shmobile_cpufreq_init();
 }
 
diff --git a/arch/arm/mach-shmobile/cpuidle.c b/arch/arm/mach-shmobile/cpuidle.c
deleted file mode 100644
index 0afeb5c..0000000
--- a/arch/arm/mach-shmobile/cpuidle.c
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- * CPUIdle support code for SH-Mobile ARM
- *
- *  Copyright (C) 2011 Magnus Damm
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/pm.h>
-#include <linux/cpuidle.h>
-#include <linux/suspend.h>
-#include <linux/module.h>
-#include <linux/err.h>
-#include <asm/cpuidle.h>
-#include <asm/io.h>
-
-static struct cpuidle_driver shmobile_cpuidle_default_driver = {
-	.name			= "shmobile_cpuidle",
-	.owner			= THIS_MODULE,
-	.states[0]		= ARM_CPUIDLE_WFI_STATE,
-	.safe_state_index	= 0, /* C1 */
-	.state_count		= 1,
-};
-
-static struct cpuidle_driver *cpuidle_drv = &shmobile_cpuidle_default_driver;
-
-void __init shmobile_cpuidle_set_driver(struct cpuidle_driver *drv)
-{
-	cpuidle_drv = drv;
-}
-
-int __init shmobile_cpuidle_init(void)
-{
-	return cpuidle_register(cpuidle_drv, NULL);
-}
diff --git a/arch/arm/mach-shmobile/pm-r8a7790.c b/arch/arm/mach-shmobile/pm-r8a7790.c
deleted file mode 100644
index 80e8d95..0000000
--- a/arch/arm/mach-shmobile/pm-r8a7790.c
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * r8a7790 Power management support
- *
- * Copyright (C) 2013  Renesas Electronics Corporation
- * Copyright (C) 2011  Renesas Solutions Corp.
- * Copyright (C) 2011  Magnus Damm
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/kernel.h>
-#include <linux/smp.h>
-#include <asm/io.h>
-#include "common.h"
-#include "pm-rcar.h"
-#include "r8a7790.h"
-
-/* RST */
-#define RST		0xe6160000
-#define CA15BAR		0x0020
-#define CA7BAR		0x0030
-#define CA15RESCNT	0x0040
-#define CA7RESCNT	0x0044
-
-/* On-chip RAM */
-#define MERAM          0xe8080000
-
-/* SYSC */
-#define SYSCIER 0x0c
-#define SYSCIMR 0x10
-
-#if defined(CONFIG_SMP)
-
-static void __init r8a7790_sysc_init(void)
-{
-	void __iomem *base = rcar_sysc_init(0xe6180000);
-
-	/* enable all interrupt sources, but do not use interrupt handler */
-	iowrite32(0x0131000e, base + SYSCIER);
-	iowrite32(0, base + SYSCIMR);
-}
-
-#else /* CONFIG_SMP */
-
-static inline void r8a7790_sysc_init(void) {}
-
-#endif /* CONFIG_SMP */
-
-void __init r8a7790_pm_init(void)
-{
-	void __iomem *p;
-	u32 bar;
-	static int once;
-
-	if (once++)
-		return;
-
-	/* MERAM for jump stub, because BAR requires 256KB aligned address */
-	p = ioremap_nocache(MERAM, shmobile_boot_size);
-	memcpy_toio(p, shmobile_boot_vector, shmobile_boot_size);
-	iounmap(p);
-
-	/* setup reset vectors */
-	p = ioremap_nocache(RST, 0x63);
-	bar = (MERAM >> 8) & 0xfffffc00;
-	writel_relaxed(bar, p + CA15BAR);
-	writel_relaxed(bar, p + CA7BAR);
-	writel_relaxed(bar | 0x10, p + CA15BAR);
-	writel_relaxed(bar | 0x10, p + CA7BAR);
-
-	/* de-assert reset for all CPUs */
-	writel_relaxed((readl_relaxed(p + CA15RESCNT) & ~0x0f) | 0xa5a50000,
-		       p + CA15RESCNT);
-	writel_relaxed((readl_relaxed(p + CA7RESCNT) & ~0x0f) | 0x5a5a0000,
-		       p + CA7RESCNT);
-	iounmap(p);
-
-	r8a7790_sysc_init();
-	shmobile_smp_apmu_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/pm-r8a7791.c b/arch/arm/mach-shmobile/pm-r8a7791.c
deleted file mode 100644
index 25f107b..0000000
--- a/arch/arm/mach-shmobile/pm-r8a7791.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * r8a7791 Power management support
- *
- * Copyright (C) 2014  Renesas Electronics Corporation
- * Copyright (C) 2011  Renesas Solutions Corp.
- * Copyright (C) 2011  Magnus Damm
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/kernel.h>
-#include <linux/smp.h>
-#include <asm/io.h>
-#include "common.h"
-#include "pm-rcar.h"
-#include "r8a7791.h"
-
-#define RST		0xe6160000
-#define CA15BAR		0x0020
-#define CA15RESCNT	0x0040
-#define RAM		0xe6300000
-
-/* SYSC */
-#define SYSCIER 0x0c
-#define SYSCIMR 0x10
-
-#if defined(CONFIG_SMP)
-
-static void __init r8a7791_sysc_init(void)
-{
-	void __iomem *base = rcar_sysc_init(0xe6180000);
-
-	/* enable all interrupt sources, but do not use interrupt handler */
-	iowrite32(0x0131000e, base + SYSCIER);
-	iowrite32(0, base + SYSCIMR);
-}
-
-#else /* CONFIG_SMP */
-
-static inline void r8a7791_sysc_init(void) {}
-
-#endif /* CONFIG_SMP */
-
-void __init r8a7791_pm_init(void)
-{
-	void __iomem *p;
-	u32 bar;
-	static int once;
-
-	if (once++)
-		return;
-
-	/* RAM for jump stub, because BAR requires 256KB aligned address */
-	p = ioremap_nocache(RAM, shmobile_boot_size);
-	memcpy_toio(p, shmobile_boot_vector, shmobile_boot_size);
-	iounmap(p);
-
-	/* setup reset vectors */
-	p = ioremap_nocache(RST, 0x63);
-	bar = (RAM >> 8) & 0xfffffc00;
-	writel_relaxed(bar, p + CA15BAR);
-	writel_relaxed(bar | 0x10, p + CA15BAR);
-
-	/* enable clocks to all CPUs */
-	writel_relaxed((readl_relaxed(p + CA15RESCNT) & ~0x0f) | 0xa5a50000,
-		       p + CA15RESCNT);
-	iounmap(p);
-
-	r8a7791_sysc_init();
-	shmobile_smp_apmu_suspend_init();
-}
diff --git a/arch/arm/mach-shmobile/pm-rcar-gen2.c b/arch/arm/mach-shmobile/pm-rcar-gen2.c
new file mode 100644
index 0000000..6815781
--- /dev/null
+++ b/arch/arm/mach-shmobile/pm-rcar-gen2.c
@@ -0,0 +1,115 @@
+/*
+ * R-Car Generation 2 Power management support
+ *
+ * Copyright (C) 2013 - 2015  Renesas Electronics Corporation
+ * Copyright (C) 2011  Renesas Solutions Corp.
+ * Copyright (C) 2011  Magnus Damm
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/smp.h>
+#include <asm/io.h>
+#include "common.h"
+#include "pm-rcar.h"
+#include "rcar-gen2.h"
+
+/* RST */
+#define RST		0xe6160000
+#define CA15BAR		0x0020
+#define CA7BAR		0x0030
+#define CA15RESCNT	0x0040
+#define CA7RESCNT	0x0044
+
+/* On-chip RAM */
+#define MERAM		0xe8080000
+#define RAM		0xe6300000
+
+/* SYSC */
+#define SYSCIER 0x0c
+#define SYSCIMR 0x10
+
+#if defined(CONFIG_SMP)
+
+static void __init rcar_gen2_sysc_init(u32 syscier)
+{
+	void __iomem *base = rcar_sysc_init(0xe6180000);
+
+	/* enable all interrupt sources, but do not use interrupt handler */
+	iowrite32(syscier, base + SYSCIER);
+	iowrite32(0, base + SYSCIMR);
+}
+
+#else /* CONFIG_SMP */
+
+static inline void rcar_gen2_sysc_init(u32 syscier) {}
+
+#endif /* CONFIG_SMP */
+
+void __init rcar_gen2_pm_init(void)
+{
+	void __iomem *p;
+	u32 bar;
+	static int once;
+	struct device_node *np, *cpus;
+	bool has_a7 = false;
+	bool has_a15 = false;
+	phys_addr_t boot_vector_addr = 0;
+	u32 syscier = 0;
+
+	if (once++)
+		return;
+
+	cpus = of_find_node_by_path("/cpus");
+	if (!cpus)
+		return;
+
+	for_each_child_of_node(cpus, np) {
+		if (of_device_is_compatible(np, "arm,cortex-a15"))
+			has_a15 = true;
+		else if (of_device_is_compatible(np, "arm,cortex-a7"))
+			has_a7 = true;
+	}
+
+	if (of_machine_is_compatible("renesas,r8a7790")) {
+		boot_vector_addr = MERAM;
+		syscier = 0x013111ef;
+
+	} else if (of_machine_is_compatible("renesas,r8a7791")) {
+		boot_vector_addr = RAM;
+		syscier = 0x00111003;
+	}
+
+	/* RAM for jump stub, because BAR requires 256KB aligned address */
+	p = ioremap_nocache(boot_vector_addr, shmobile_boot_size);
+	memcpy_toio(p, shmobile_boot_vector, shmobile_boot_size);
+	iounmap(p);
+
+	/* setup reset vectors */
+	p = ioremap_nocache(RST, 0x63);
+	bar = (boot_vector_addr >> 8) & 0xfffffc00;
+	if (has_a15) {
+		writel_relaxed(bar, p + CA15BAR);
+		writel_relaxed(bar | 0x10, p + CA15BAR);
+
+		/* de-assert reset for CA15 CPUs */
+		writel_relaxed((readl_relaxed(p + CA15RESCNT) & ~0x0f) |
+				0xa5a50000, p + CA15RESCNT);
+	}
+	if (has_a7) {
+		writel_relaxed(bar, p + CA7BAR);
+		writel_relaxed(bar | 0x10, p + CA7BAR);
+
+		/* de-assert reset for CA7 CPUs */
+		writel_relaxed((readl_relaxed(p + CA7RESCNT) & ~0x0f) |
+				0x5a5a0000, p + CA7RESCNT);
+	}
+	iounmap(p);
+
+	rcar_gen2_sysc_init(syscier);
+	shmobile_smp_apmu_suspend_init();
+}
diff --git a/arch/arm/mach-shmobile/pm-sh7372.c b/arch/arm/mach-shmobile/pm-sh7372.c
index c0293ae..9f19052 100644
--- a/arch/arm/mach-shmobile/pm-sh7372.c
+++ b/arch/arm/mach-shmobile/pm-sh7372.c
@@ -462,7 +462,7 @@
 
 static void __init sh7372_cpuidle_init(void)
 {
-	shmobile_cpuidle_set_driver(&sh7372_cpuidle_driver);
+	return cpuidle_register(cpuidle_drv, NULL);
 }
 #else
 static void __init sh7372_cpuidle_init(void) {}
diff --git a/arch/arm/mach-shmobile/r8a7790.h b/arch/arm/mach-shmobile/r8a7790.h
index bf73a85..1a46d02 100644
--- a/arch/arm/mach-shmobile/r8a7790.h
+++ b/arch/arm/mach-shmobile/r8a7790.h
@@ -1,7 +1,6 @@
 #ifndef __ASM_R8A7790_H__
 #define __ASM_R8A7790_H__
 
-void r8a7790_pm_init(void);
 extern struct smp_operations r8a7790_smp_ops;
 
 #endif /* __ASM_R8A7790_H__ */
diff --git a/arch/arm/mach-shmobile/r8a7791.h b/arch/arm/mach-shmobile/r8a7791.h
index 6cf11eb..7ca0b7d 100644
--- a/arch/arm/mach-shmobile/r8a7791.h
+++ b/arch/arm/mach-shmobile/r8a7791.h
@@ -1,7 +1,6 @@
 #ifndef __ASM_R8A7791_H__
 #define __ASM_R8A7791_H__
 
-void r8a7791_pm_init(void);
 extern struct smp_operations r8a7791_smp_ops;
 
 #endif /* __ASM_R8A7791_H__ */
diff --git a/arch/arm/mach-shmobile/rcar-gen2.h b/arch/arm/mach-shmobile/rcar-gen2.h
index ce53cb5..8a66b4a 100644
--- a/arch/arm/mach-shmobile/rcar-gen2.h
+++ b/arch/arm/mach-shmobile/rcar-gen2.h
@@ -5,5 +5,6 @@
 #define MD(nr) BIT(nr)
 u32 rcar_gen2_read_mode_pins(void);
 void rcar_gen2_reserve(void);
+void rcar_gen2_pm_init(void);
 
 #endif /* __ASM_RCAR_GEN2_H__ */
diff --git a/arch/arm/mach-shmobile/setup-r8a7740.c b/arch/arm/mach-shmobile/setup-r8a7740.c
index dd64caf..9832e48 100644
--- a/arch/arm/mach-shmobile/setup-r8a7740.c
+++ b/arch/arm/mach-shmobile/setup-r8a7740.c
@@ -842,13 +842,6 @@
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
-#define RESCNT2 IOMEM(0xe6188020)
-static void r8a7740_restart(enum reboot_mode mode, const char *cmd)
-{
-	/* Do soft power on reset */
-	writel(1 << 31, RESCNT2);
-}
-
 static const char *r8a7740_boards_compat_dt[] __initdata = {
 	"renesas,r8a7740",
 	NULL,
@@ -861,7 +854,6 @@
 	.init_machine	= r8a7740_generic_init,
 	.init_late	= shmobile_init_late,
 	.dt_compat	= r8a7740_boards_compat_dt,
-	.restart	= r8a7740_restart,
 MACHINE_END
 
 #endif /* CONFIG_USE_OF */
diff --git a/arch/arm/mach-shmobile/setup-rcar-gen2.c b/arch/arm/mach-shmobile/setup-rcar-gen2.c
index d1fa625..51464cc 100644
--- a/arch/arm/mach-shmobile/setup-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/setup-rcar-gen2.c
@@ -50,9 +50,7 @@
 
 void __init rcar_gen2_timer_init(void)
 {
-#if defined(CONFIG_ARM_ARCH_TIMER) || defined(CONFIG_COMMON_CLK)
 	u32 mode = rcar_gen2_read_mode_pins();
-#endif
 #ifdef CONFIG_ARM_ARCH_TIMER
 	void __iomem *base;
 	int extal_mhz = 0;
@@ -128,9 +126,7 @@
 	iounmap(base);
 #endif /* CONFIG_ARM_ARCH_TIMER */
 
-#ifdef CONFIG_COMMON_CLK
 	rcar_gen2_clocks_init(mode);
-#endif
 #ifdef CONFIG_ARCH_SHMOBILE_MULTI
 	clocksource_of_init();
 #endif
diff --git a/arch/arm/mach-shmobile/smp-r8a7790.c b/arch/arm/mach-shmobile/smp-r8a7790.c
index 9c3da13..f8be415 100644
--- a/arch/arm/mach-shmobile/smp-r8a7790.c
+++ b/arch/arm/mach-shmobile/smp-r8a7790.c
@@ -23,6 +23,7 @@
 #include "common.h"
 #include "platsmp-apmu.h"
 #include "pm-rcar.h"
+#include "rcar-gen2.h"
 #include "r8a7790.h"
 
 static struct rcar_sysc_ch r8a7790_ca15_scu = {
@@ -54,7 +55,7 @@
 				       ARRAY_SIZE(r8a7790_apmu_config));
 
 	/* turn on power to SCU */
-	r8a7790_pm_init();
+	rcar_gen2_pm_init();
 	rcar_sysc_power_up(&r8a7790_ca15_scu);
 	rcar_sysc_power_up(&r8a7790_ca7_scu);
 }
diff --git a/arch/arm/mach-shmobile/smp-r8a7791.c b/arch/arm/mach-shmobile/smp-r8a7791.c
index 7e49e0a..6658682 100644
--- a/arch/arm/mach-shmobile/smp-r8a7791.c
+++ b/arch/arm/mach-shmobile/smp-r8a7791.c
@@ -39,7 +39,7 @@
 				       r8a7791_apmu_config,
 				       ARRAY_SIZE(r8a7791_apmu_config));
 
-	r8a7791_pm_init();
+	rcar_gen2_pm_init();
 }
 
 static int r8a7791_smp_boot_secondary(unsigned int cpu,
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 38d875d..caefe80 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -272,14 +272,6 @@
 	  Say Y here if you're going to use hardware that connects to the
 	  MPC512x/831x/834x/837x/8572/8610 GPIOs.
 
-config GPIO_MSM_V1
-	tristate "Qualcomm MSM GPIO v1"
-	depends on GPIOLIB && ARCH_MSM && (ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50)
-	help
-	  Say yes here to support the GPIO interface on ARM v6 based
-	  Qualcomm MSM chips.  Most of the pins on the MSM can be
-	  selected for GPIO, and are controlled by this driver.
-
 config GPIO_MSM_V2
 	tristate "Qualcomm MSM GPIO v2"
 	depends on GPIOLIB && OF && ARCH_QCOM
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 07b816b..f71bb97 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -60,7 +60,6 @@
 obj-$(CONFIG_GPIO_MPC5200)	+= gpio-mpc5200.o
 obj-$(CONFIG_GPIO_MPC8XXX)	+= gpio-mpc8xxx.o
 obj-$(CONFIG_GPIO_MSIC)		+= gpio-msic.o
-obj-$(CONFIG_GPIO_MSM_V1)	+= gpio-msm-v1.o
 obj-$(CONFIG_GPIO_MSM_V2)	+= gpio-msm-v2.o
 obj-$(CONFIG_GPIO_MVEBU)        += gpio-mvebu.o
 obj-$(CONFIG_GPIO_MXC)		+= gpio-mxc.o
diff --git a/drivers/gpio/gpio-msm-v1.c b/drivers/gpio/gpio-msm-v1.c
deleted file mode 100644
index edf285e..0000000
--- a/drivers/gpio/gpio-msm-v1.c
+++ /dev/null
@@ -1,714 +0,0 @@
-/*
- * Copyright (C) 2007 Google, Inc.
- * Copyright (c) 2009-2012, The Linux Foundation. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- */
-
-#include <linux/bitops.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/err.h>
-
-#include <mach/msm_gpiomux.h>
-
-/* see 80-VA736-2 Rev C pp 695-751
-**
-** These are actually the *shadow* gpio registers, since the
-** real ones (which allow full access) are only available to the
-** ARM9 side of the world.
-**
-** Since the _BASE need to be page-aligned when we're mapping them
-** to virtual addresses, adjust for the additional offset in these
-** macros.
-*/
-
-#define MSM_GPIO1_REG(off) (off)
-#define MSM_GPIO2_REG(off) (off)
-#define MSM_GPIO1_SHADOW_REG(off) (off)
-#define MSM_GPIO2_SHADOW_REG(off) (off)
-
-/*
- * MSM7X00 registers
- */
-/* output value */
-#define MSM7X00_GPIO_OUT_0	MSM_GPIO1_SHADOW_REG(0x00)  /* gpio  15-0  */
-#define MSM7X00_GPIO_OUT_1	MSM_GPIO2_SHADOW_REG(0x00)  /* gpio  42-16 */
-#define MSM7X00_GPIO_OUT_2	MSM_GPIO1_SHADOW_REG(0x04)  /* gpio  67-43 */
-#define MSM7X00_GPIO_OUT_3	MSM_GPIO1_SHADOW_REG(0x08)  /* gpio  94-68 */
-#define MSM7X00_GPIO_OUT_4	MSM_GPIO1_SHADOW_REG(0x0C)  /* gpio 106-95 */
-#define MSM7X00_GPIO_OUT_5	MSM_GPIO1_SHADOW_REG(0x50)  /* gpio 107-121 */
-
-/* same pin map as above, output enable */
-#define MSM7X00_GPIO_OE_0	MSM_GPIO1_SHADOW_REG(0x10)
-#define MSM7X00_GPIO_OE_1	MSM_GPIO2_SHADOW_REG(0x08)
-#define MSM7X00_GPIO_OE_2	MSM_GPIO1_SHADOW_REG(0x14)
-#define MSM7X00_GPIO_OE_3	MSM_GPIO1_SHADOW_REG(0x18)
-#define MSM7X00_GPIO_OE_4	MSM_GPIO1_SHADOW_REG(0x1C)
-#define MSM7X00_GPIO_OE_5	MSM_GPIO1_SHADOW_REG(0x54)
-
-/* same pin map as above, input read */
-#define MSM7X00_GPIO_IN_0	MSM_GPIO1_SHADOW_REG(0x34)
-#define MSM7X00_GPIO_IN_1	MSM_GPIO2_SHADOW_REG(0x20)
-#define MSM7X00_GPIO_IN_2	MSM_GPIO1_SHADOW_REG(0x38)
-#define MSM7X00_GPIO_IN_3	MSM_GPIO1_SHADOW_REG(0x3C)
-#define MSM7X00_GPIO_IN_4	MSM_GPIO1_SHADOW_REG(0x40)
-#define MSM7X00_GPIO_IN_5	MSM_GPIO1_SHADOW_REG(0x44)
-
-/* same pin map as above, 1=edge 0=level interrup */
-#define MSM7X00_GPIO_INT_EDGE_0	MSM_GPIO1_SHADOW_REG(0x60)
-#define MSM7X00_GPIO_INT_EDGE_1	MSM_GPIO2_SHADOW_REG(0x50)
-#define MSM7X00_GPIO_INT_EDGE_2	MSM_GPIO1_SHADOW_REG(0x64)
-#define MSM7X00_GPIO_INT_EDGE_3	MSM_GPIO1_SHADOW_REG(0x68)
-#define MSM7X00_GPIO_INT_EDGE_4	MSM_GPIO1_SHADOW_REG(0x6C)
-#define MSM7X00_GPIO_INT_EDGE_5	MSM_GPIO1_SHADOW_REG(0xC0)
-
-/* same pin map as above, 1=positive 0=negative */
-#define MSM7X00_GPIO_INT_POS_0	MSM_GPIO1_SHADOW_REG(0x70)
-#define MSM7X00_GPIO_INT_POS_1	MSM_GPIO2_SHADOW_REG(0x58)
-#define MSM7X00_GPIO_INT_POS_2	MSM_GPIO1_SHADOW_REG(0x74)
-#define MSM7X00_GPIO_INT_POS_3	MSM_GPIO1_SHADOW_REG(0x78)
-#define MSM7X00_GPIO_INT_POS_4	MSM_GPIO1_SHADOW_REG(0x7C)
-#define MSM7X00_GPIO_INT_POS_5	MSM_GPIO1_SHADOW_REG(0xBC)
-
-/* same pin map as above, interrupt enable */
-#define MSM7X00_GPIO_INT_EN_0	MSM_GPIO1_SHADOW_REG(0x80)
-#define MSM7X00_GPIO_INT_EN_1	MSM_GPIO2_SHADOW_REG(0x60)
-#define MSM7X00_GPIO_INT_EN_2	MSM_GPIO1_SHADOW_REG(0x84)
-#define MSM7X00_GPIO_INT_EN_3	MSM_GPIO1_SHADOW_REG(0x88)
-#define MSM7X00_GPIO_INT_EN_4	MSM_GPIO1_SHADOW_REG(0x8C)
-#define MSM7X00_GPIO_INT_EN_5	MSM_GPIO1_SHADOW_REG(0xB8)
-
-/* same pin map as above, write 1 to clear interrupt */
-#define MSM7X00_GPIO_INT_CLEAR_0	MSM_GPIO1_SHADOW_REG(0x90)
-#define MSM7X00_GPIO_INT_CLEAR_1	MSM_GPIO2_SHADOW_REG(0x68)
-#define MSM7X00_GPIO_INT_CLEAR_2	MSM_GPIO1_SHADOW_REG(0x94)
-#define MSM7X00_GPIO_INT_CLEAR_3	MSM_GPIO1_SHADOW_REG(0x98)
-#define MSM7X00_GPIO_INT_CLEAR_4	MSM_GPIO1_SHADOW_REG(0x9C)
-#define MSM7X00_GPIO_INT_CLEAR_5	MSM_GPIO1_SHADOW_REG(0xB4)
-
-/* same pin map as above, 1=interrupt pending */
-#define MSM7X00_GPIO_INT_STATUS_0	MSM_GPIO1_SHADOW_REG(0xA0)
-#define MSM7X00_GPIO_INT_STATUS_1	MSM_GPIO2_SHADOW_REG(0x70)
-#define MSM7X00_GPIO_INT_STATUS_2	MSM_GPIO1_SHADOW_REG(0xA4)
-#define MSM7X00_GPIO_INT_STATUS_3	MSM_GPIO1_SHADOW_REG(0xA8)
-#define MSM7X00_GPIO_INT_STATUS_4	MSM_GPIO1_SHADOW_REG(0xAC)
-#define MSM7X00_GPIO_INT_STATUS_5	MSM_GPIO1_SHADOW_REG(0xB0)
-
-/*
- * QSD8X50 registers
- */
-/* output value */
-#define QSD8X50_GPIO_OUT_0	MSM_GPIO1_SHADOW_REG(0x00)  /* gpio  15-0   */
-#define QSD8X50_GPIO_OUT_1	MSM_GPIO2_SHADOW_REG(0x00)  /* gpio  42-16  */
-#define QSD8X50_GPIO_OUT_2	MSM_GPIO1_SHADOW_REG(0x04)  /* gpio  67-43  */
-#define QSD8X50_GPIO_OUT_3	MSM_GPIO1_SHADOW_REG(0x08)  /* gpio  94-68  */
-#define QSD8X50_GPIO_OUT_4	MSM_GPIO1_SHADOW_REG(0x0C)  /* gpio 103-95  */
-#define QSD8X50_GPIO_OUT_5	MSM_GPIO1_SHADOW_REG(0x10)  /* gpio 121-104 */
-#define QSD8X50_GPIO_OUT_6	MSM_GPIO1_SHADOW_REG(0x14)  /* gpio 152-122 */
-#define QSD8X50_GPIO_OUT_7	MSM_GPIO1_SHADOW_REG(0x18)  /* gpio 164-153 */
-
-/* same pin map as above, output enable */
-#define QSD8X50_GPIO_OE_0	MSM_GPIO1_SHADOW_REG(0x20)
-#define QSD8X50_GPIO_OE_1	MSM_GPIO2_SHADOW_REG(0x08)
-#define QSD8X50_GPIO_OE_2	MSM_GPIO1_SHADOW_REG(0x24)
-#define QSD8X50_GPIO_OE_3	MSM_GPIO1_SHADOW_REG(0x28)
-#define QSD8X50_GPIO_OE_4	MSM_GPIO1_SHADOW_REG(0x2C)
-#define QSD8X50_GPIO_OE_5	MSM_GPIO1_SHADOW_REG(0x30)
-#define QSD8X50_GPIO_OE_6	MSM_GPIO1_SHADOW_REG(0x34)
-#define QSD8X50_GPIO_OE_7	MSM_GPIO1_SHADOW_REG(0x38)
-
-/* same pin map as above, input read */
-#define QSD8X50_GPIO_IN_0	MSM_GPIO1_SHADOW_REG(0x50)
-#define QSD8X50_GPIO_IN_1	MSM_GPIO2_SHADOW_REG(0x20)
-#define QSD8X50_GPIO_IN_2	MSM_GPIO1_SHADOW_REG(0x54)
-#define QSD8X50_GPIO_IN_3	MSM_GPIO1_SHADOW_REG(0x58)
-#define QSD8X50_GPIO_IN_4	MSM_GPIO1_SHADOW_REG(0x5C)
-#define QSD8X50_GPIO_IN_5	MSM_GPIO1_SHADOW_REG(0x60)
-#define QSD8X50_GPIO_IN_6	MSM_GPIO1_SHADOW_REG(0x64)
-#define QSD8X50_GPIO_IN_7	MSM_GPIO1_SHADOW_REG(0x68)
-
-/* same pin map as above, 1=edge 0=level interrup */
-#define QSD8X50_GPIO_INT_EDGE_0	MSM_GPIO1_SHADOW_REG(0x70)
-#define QSD8X50_GPIO_INT_EDGE_1	MSM_GPIO2_SHADOW_REG(0x50)
-#define QSD8X50_GPIO_INT_EDGE_2	MSM_GPIO1_SHADOW_REG(0x74)
-#define QSD8X50_GPIO_INT_EDGE_3	MSM_GPIO1_SHADOW_REG(0x78)
-#define QSD8X50_GPIO_INT_EDGE_4	MSM_GPIO1_SHADOW_REG(0x7C)
-#define QSD8X50_GPIO_INT_EDGE_5	MSM_GPIO1_SHADOW_REG(0x80)
-#define QSD8X50_GPIO_INT_EDGE_6	MSM_GPIO1_SHADOW_REG(0x84)
-#define QSD8X50_GPIO_INT_EDGE_7	MSM_GPIO1_SHADOW_REG(0x88)
-
-/* same pin map as above, 1=positive 0=negative */
-#define QSD8X50_GPIO_INT_POS_0	MSM_GPIO1_SHADOW_REG(0x90)
-#define QSD8X50_GPIO_INT_POS_1	MSM_GPIO2_SHADOW_REG(0x58)
-#define QSD8X50_GPIO_INT_POS_2	MSM_GPIO1_SHADOW_REG(0x94)
-#define QSD8X50_GPIO_INT_POS_3	MSM_GPIO1_SHADOW_REG(0x98)
-#define QSD8X50_GPIO_INT_POS_4	MSM_GPIO1_SHADOW_REG(0x9C)
-#define QSD8X50_GPIO_INT_POS_5	MSM_GPIO1_SHADOW_REG(0xA0)
-#define QSD8X50_GPIO_INT_POS_6	MSM_GPIO1_SHADOW_REG(0xA4)
-#define QSD8X50_GPIO_INT_POS_7	MSM_GPIO1_SHADOW_REG(0xA8)
-
-/* same pin map as above, interrupt enable */
-#define QSD8X50_GPIO_INT_EN_0	MSM_GPIO1_SHADOW_REG(0xB0)
-#define QSD8X50_GPIO_INT_EN_1	MSM_GPIO2_SHADOW_REG(0x60)
-#define QSD8X50_GPIO_INT_EN_2	MSM_GPIO1_SHADOW_REG(0xB4)
-#define QSD8X50_GPIO_INT_EN_3	MSM_GPIO1_SHADOW_REG(0xB8)
-#define QSD8X50_GPIO_INT_EN_4	MSM_GPIO1_SHADOW_REG(0xBC)
-#define QSD8X50_GPIO_INT_EN_5	MSM_GPIO1_SHADOW_REG(0xC0)
-#define QSD8X50_GPIO_INT_EN_6	MSM_GPIO1_SHADOW_REG(0xC4)
-#define QSD8X50_GPIO_INT_EN_7	MSM_GPIO1_SHADOW_REG(0xC8)
-
-/* same pin map as above, write 1 to clear interrupt */
-#define QSD8X50_GPIO_INT_CLEAR_0	MSM_GPIO1_SHADOW_REG(0xD0)
-#define QSD8X50_GPIO_INT_CLEAR_1	MSM_GPIO2_SHADOW_REG(0x68)
-#define QSD8X50_GPIO_INT_CLEAR_2	MSM_GPIO1_SHADOW_REG(0xD4)
-#define QSD8X50_GPIO_INT_CLEAR_3	MSM_GPIO1_SHADOW_REG(0xD8)
-#define QSD8X50_GPIO_INT_CLEAR_4	MSM_GPIO1_SHADOW_REG(0xDC)
-#define QSD8X50_GPIO_INT_CLEAR_5	MSM_GPIO1_SHADOW_REG(0xE0)
-#define QSD8X50_GPIO_INT_CLEAR_6	MSM_GPIO1_SHADOW_REG(0xE4)
-#define QSD8X50_GPIO_INT_CLEAR_7	MSM_GPIO1_SHADOW_REG(0xE8)
-
-/* same pin map as above, 1=interrupt pending */
-#define QSD8X50_GPIO_INT_STATUS_0	MSM_GPIO1_SHADOW_REG(0xF0)
-#define QSD8X50_GPIO_INT_STATUS_1	MSM_GPIO2_SHADOW_REG(0x70)
-#define QSD8X50_GPIO_INT_STATUS_2	MSM_GPIO1_SHADOW_REG(0xF4)
-#define QSD8X50_GPIO_INT_STATUS_3	MSM_GPIO1_SHADOW_REG(0xF8)
-#define QSD8X50_GPIO_INT_STATUS_4	MSM_GPIO1_SHADOW_REG(0xFC)
-#define QSD8X50_GPIO_INT_STATUS_5	MSM_GPIO1_SHADOW_REG(0x100)
-#define QSD8X50_GPIO_INT_STATUS_6	MSM_GPIO1_SHADOW_REG(0x104)
-#define QSD8X50_GPIO_INT_STATUS_7	MSM_GPIO1_SHADOW_REG(0x108)
-
-/*
- * MSM7X30 registers
- */
-/* output value */
-#define MSM7X30_GPIO_OUT_0	MSM_GPIO1_REG(0x00)   /* gpio  15-0   */
-#define MSM7X30_GPIO_OUT_1	MSM_GPIO2_REG(0x00)   /* gpio  43-16  */
-#define MSM7X30_GPIO_OUT_2	MSM_GPIO1_REG(0x04)   /* gpio  67-44  */
-#define MSM7X30_GPIO_OUT_3	MSM_GPIO1_REG(0x08)   /* gpio  94-68  */
-#define MSM7X30_GPIO_OUT_4	MSM_GPIO1_REG(0x0C)   /* gpio 106-95  */
-#define MSM7X30_GPIO_OUT_5	MSM_GPIO1_REG(0x50)   /* gpio 133-107 */
-#define MSM7X30_GPIO_OUT_6	MSM_GPIO1_REG(0xC4)   /* gpio 150-134 */
-#define MSM7X30_GPIO_OUT_7	MSM_GPIO1_REG(0x214)  /* gpio 181-151 */
-
-/* same pin map as above, output enable */
-#define MSM7X30_GPIO_OE_0	MSM_GPIO1_REG(0x10)
-#define MSM7X30_GPIO_OE_1	MSM_GPIO2_REG(0x08)
-#define MSM7X30_GPIO_OE_2	MSM_GPIO1_REG(0x14)
-#define MSM7X30_GPIO_OE_3	MSM_GPIO1_REG(0x18)
-#define MSM7X30_GPIO_OE_4	MSM_GPIO1_REG(0x1C)
-#define MSM7X30_GPIO_OE_5	MSM_GPIO1_REG(0x54)
-#define MSM7X30_GPIO_OE_6	MSM_GPIO1_REG(0xC8)
-#define MSM7X30_GPIO_OE_7	MSM_GPIO1_REG(0x218)
-
-/* same pin map as above, input read */
-#define MSM7X30_GPIO_IN_0	MSM_GPIO1_REG(0x34)
-#define MSM7X30_GPIO_IN_1	MSM_GPIO2_REG(0x20)
-#define MSM7X30_GPIO_IN_2	MSM_GPIO1_REG(0x38)
-#define MSM7X30_GPIO_IN_3	MSM_GPIO1_REG(0x3C)
-#define MSM7X30_GPIO_IN_4	MSM_GPIO1_REG(0x40)
-#define MSM7X30_GPIO_IN_5	MSM_GPIO1_REG(0x44)
-#define MSM7X30_GPIO_IN_6	MSM_GPIO1_REG(0xCC)
-#define MSM7X30_GPIO_IN_7	MSM_GPIO1_REG(0x21C)
-
-/* same pin map as above, 1=edge 0=level interrup */
-#define MSM7X30_GPIO_INT_EDGE_0	MSM_GPIO1_REG(0x60)
-#define MSM7X30_GPIO_INT_EDGE_1	MSM_GPIO2_REG(0x50)
-#define MSM7X30_GPIO_INT_EDGE_2	MSM_GPIO1_REG(0x64)
-#define MSM7X30_GPIO_INT_EDGE_3	MSM_GPIO1_REG(0x68)
-#define MSM7X30_GPIO_INT_EDGE_4	MSM_GPIO1_REG(0x6C)
-#define MSM7X30_GPIO_INT_EDGE_5	MSM_GPIO1_REG(0xC0)
-#define MSM7X30_GPIO_INT_EDGE_6	MSM_GPIO1_REG(0xD0)
-#define MSM7X30_GPIO_INT_EDGE_7	MSM_GPIO1_REG(0x240)
-
-/* same pin map as above, 1=positive 0=negative */
-#define MSM7X30_GPIO_INT_POS_0	MSM_GPIO1_REG(0x70)
-#define MSM7X30_GPIO_INT_POS_1	MSM_GPIO2_REG(0x58)
-#define MSM7X30_GPIO_INT_POS_2	MSM_GPIO1_REG(0x74)
-#define MSM7X30_GPIO_INT_POS_3	MSM_GPIO1_REG(0x78)
-#define MSM7X30_GPIO_INT_POS_4	MSM_GPIO1_REG(0x7C)
-#define MSM7X30_GPIO_INT_POS_5	MSM_GPIO1_REG(0xBC)
-#define MSM7X30_GPIO_INT_POS_6	MSM_GPIO1_REG(0xD4)
-#define MSM7X30_GPIO_INT_POS_7	MSM_GPIO1_REG(0x228)
-
-/* same pin map as above, interrupt enable */
-#define MSM7X30_GPIO_INT_EN_0	MSM_GPIO1_REG(0x80)
-#define MSM7X30_GPIO_INT_EN_1	MSM_GPIO2_REG(0x60)
-#define MSM7X30_GPIO_INT_EN_2	MSM_GPIO1_REG(0x84)
-#define MSM7X30_GPIO_INT_EN_3	MSM_GPIO1_REG(0x88)
-#define MSM7X30_GPIO_INT_EN_4	MSM_GPIO1_REG(0x8C)
-#define MSM7X30_GPIO_INT_EN_5	MSM_GPIO1_REG(0xB8)
-#define MSM7X30_GPIO_INT_EN_6	MSM_GPIO1_REG(0xD8)
-#define MSM7X30_GPIO_INT_EN_7	MSM_GPIO1_REG(0x22C)
-
-/* same pin map as above, write 1 to clear interrupt */
-#define MSM7X30_GPIO_INT_CLEAR_0	MSM_GPIO1_REG(0x90)
-#define MSM7X30_GPIO_INT_CLEAR_1	MSM_GPIO2_REG(0x68)
-#define MSM7X30_GPIO_INT_CLEAR_2	MSM_GPIO1_REG(0x94)
-#define MSM7X30_GPIO_INT_CLEAR_3	MSM_GPIO1_REG(0x98)
-#define MSM7X30_GPIO_INT_CLEAR_4	MSM_GPIO1_REG(0x9C)
-#define MSM7X30_GPIO_INT_CLEAR_5	MSM_GPIO1_REG(0xB4)
-#define MSM7X30_GPIO_INT_CLEAR_6	MSM_GPIO1_REG(0xDC)
-#define MSM7X30_GPIO_INT_CLEAR_7	MSM_GPIO1_REG(0x230)
-
-/* same pin map as above, 1=interrupt pending */
-#define MSM7X30_GPIO_INT_STATUS_0	MSM_GPIO1_REG(0xA0)
-#define MSM7X30_GPIO_INT_STATUS_1	MSM_GPIO2_REG(0x70)
-#define MSM7X30_GPIO_INT_STATUS_2	MSM_GPIO1_REG(0xA4)
-#define MSM7X30_GPIO_INT_STATUS_3	MSM_GPIO1_REG(0xA8)
-#define MSM7X30_GPIO_INT_STATUS_4	MSM_GPIO1_REG(0xAC)
-#define MSM7X30_GPIO_INT_STATUS_5	MSM_GPIO1_REG(0xB0)
-#define MSM7X30_GPIO_INT_STATUS_6	MSM_GPIO1_REG(0xE0)
-#define MSM7X30_GPIO_INT_STATUS_7	MSM_GPIO1_REG(0x234)
-
-#define FIRST_GPIO_IRQ MSM_GPIO_TO_INT(0)
-
-#define MSM_GPIO_BANK(soc, bank, first, last)				\
-	{								\
-		.regs[MSM_GPIO_OUT] =         soc##_GPIO_OUT_##bank,	\
-		.regs[MSM_GPIO_IN] =          soc##_GPIO_IN_##bank,	\
-		.regs[MSM_GPIO_INT_STATUS] =  soc##_GPIO_INT_STATUS_##bank, \
-		.regs[MSM_GPIO_INT_CLEAR] =   soc##_GPIO_INT_CLEAR_##bank, \
-		.regs[MSM_GPIO_INT_EN] =      soc##_GPIO_INT_EN_##bank,	\
-		.regs[MSM_GPIO_INT_EDGE] =    soc##_GPIO_INT_EDGE_##bank, \
-		.regs[MSM_GPIO_INT_POS] =     soc##_GPIO_INT_POS_##bank, \
-		.regs[MSM_GPIO_OE] =          soc##_GPIO_OE_##bank,	\
-		.chip = {						\
-			.base = (first),				\
-			.ngpio = (last) - (first) + 1,			\
-			.get = msm_gpio_get,				\
-			.set = msm_gpio_set,				\
-			.direction_input = msm_gpio_direction_input,	\
-			.direction_output = msm_gpio_direction_output,	\
-			.to_irq = msm_gpio_to_irq,			\
-			.request = msm_gpio_request,			\
-			.free = msm_gpio_free,				\
-		}							\
-	}
-
-#define MSM_GPIO_BROKEN_INT_CLEAR 1
-
-enum msm_gpio_reg {
-	MSM_GPIO_IN,
-	MSM_GPIO_OUT,
-	MSM_GPIO_INT_STATUS,
-	MSM_GPIO_INT_CLEAR,
-	MSM_GPIO_INT_EN,
-	MSM_GPIO_INT_EDGE,
-	MSM_GPIO_INT_POS,
-	MSM_GPIO_OE,
-	MSM_GPIO_REG_NR
-};
-
-struct msm_gpio_chip {
-	spinlock_t		lock;
-	struct gpio_chip	chip;
-	unsigned long		regs[MSM_GPIO_REG_NR];
-#if MSM_GPIO_BROKEN_INT_CLEAR
-	unsigned                int_status_copy;
-#endif
-	unsigned int            both_edge_detect;
-	unsigned int            int_enable[2]; /* 0: awake, 1: sleep */
-	void __iomem		*base;
-};
-
-struct msm_gpio_initdata {
-	struct msm_gpio_chip *chips;
-	int count;
-};
-
-static void msm_gpio_writel(struct msm_gpio_chip *chip, u32 val,
-			    enum msm_gpio_reg reg)
-{
-	writel(val, chip->base + chip->regs[reg]);
-}
-
-static u32 msm_gpio_readl(struct msm_gpio_chip *chip, enum msm_gpio_reg reg)
-{
-	return readl(chip->base + chip->regs[reg]);
-}
-
-static int msm_gpio_write(struct msm_gpio_chip *msm_chip,
-			  unsigned offset, unsigned on)
-{
-	unsigned mask = BIT(offset);
-	unsigned val;
-
-	val = msm_gpio_readl(msm_chip, MSM_GPIO_OUT);
-	if (on)
-		msm_gpio_writel(msm_chip, val | mask, MSM_GPIO_OUT);
-	else
-		msm_gpio_writel(msm_chip, val & ~mask, MSM_GPIO_OUT);
-	return 0;
-}
-
-static void msm_gpio_update_both_edge_detect(struct msm_gpio_chip *msm_chip)
-{
-	int loop_limit = 100;
-	unsigned pol, val, val2, intstat;
-	do {
-		val = msm_gpio_readl(msm_chip, MSM_GPIO_IN);
-		pol = msm_gpio_readl(msm_chip, MSM_GPIO_INT_POS);
-		pol = (pol & ~msm_chip->both_edge_detect) |
-		      (~val & msm_chip->both_edge_detect);
-		msm_gpio_writel(msm_chip, pol, MSM_GPIO_INT_POS);
-		intstat = msm_gpio_readl(msm_chip, MSM_GPIO_INT_STATUS);
-		val2 = msm_gpio_readl(msm_chip, MSM_GPIO_IN);
-		if (((val ^ val2) & msm_chip->both_edge_detect & ~intstat) == 0)
-			return;
-	} while (loop_limit-- > 0);
-	printk(KERN_ERR "msm_gpio_update_both_edge_detect, "
-	       "failed to reach stable state %x != %x\n", val, val2);
-}
-
-static int msm_gpio_clear_detect_status(struct msm_gpio_chip *msm_chip,
-					unsigned offset)
-{
-	unsigned bit = BIT(offset);
-
-#if MSM_GPIO_BROKEN_INT_CLEAR
-	/* Save interrupts that already triggered before we loose them. */
-	/* Any interrupt that triggers between the read of int_status */
-	/* and the write to int_clear will still be lost though. */
-	msm_chip->int_status_copy |=
-		msm_gpio_readl(msm_chip, MSM_GPIO_INT_STATUS);
-	msm_chip->int_status_copy &= ~bit;
-#endif
-	msm_gpio_writel(msm_chip, bit, MSM_GPIO_INT_CLEAR);
-	msm_gpio_update_both_edge_detect(msm_chip);
-	return 0;
-}
-
-static int msm_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
-{
-	struct msm_gpio_chip *msm_chip;
-	unsigned long irq_flags;
-	u32 val;
-
-	msm_chip = container_of(chip, struct msm_gpio_chip, chip);
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	val = msm_gpio_readl(msm_chip, MSM_GPIO_OE) & ~BIT(offset);
-	msm_gpio_writel(msm_chip, val, MSM_GPIO_OE);
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-	return 0;
-}
-
-static int
-msm_gpio_direction_output(struct gpio_chip *chip, unsigned offset, int value)
-{
-	struct msm_gpio_chip *msm_chip;
-	unsigned long irq_flags;
-	u32 val;
-
-	msm_chip = container_of(chip, struct msm_gpio_chip, chip);
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	msm_gpio_write(msm_chip, offset, value);
-	val = msm_gpio_readl(msm_chip, MSM_GPIO_OE) | BIT(offset);
-	msm_gpio_writel(msm_chip, val, MSM_GPIO_OE);
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-	return 0;
-}
-
-static int msm_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
-	struct msm_gpio_chip *msm_chip;
-
-	msm_chip = container_of(chip, struct msm_gpio_chip, chip);
-	return (msm_gpio_readl(msm_chip, MSM_GPIO_IN) & (1U << offset)) ? 1 : 0;
-}
-
-static void msm_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
-	struct msm_gpio_chip *msm_chip;
-	unsigned long irq_flags;
-
-	msm_chip = container_of(chip, struct msm_gpio_chip, chip);
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	msm_gpio_write(msm_chip, offset, value);
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-}
-
-static int msm_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	return MSM_GPIO_TO_INT(chip->base + offset);
-}
-
-#ifdef CONFIG_MSM_GPIOMUX
-static int msm_gpio_request(struct gpio_chip *chip, unsigned offset)
-{
-	return msm_gpiomux_get(chip->base + offset);
-}
-
-static void msm_gpio_free(struct gpio_chip *chip, unsigned offset)
-{
-	msm_gpiomux_put(chip->base + offset);
-}
-#else
-#define msm_gpio_request NULL
-#define msm_gpio_free NULL
-#endif
-
-static struct msm_gpio_chip *msm_gpio_chips;
-static int msm_gpio_count;
-
-static struct msm_gpio_chip msm_gpio_chips_msm7x01[] = {
-	MSM_GPIO_BANK(MSM7X00, 0,   0,  15),
-	MSM_GPIO_BANK(MSM7X00, 1,  16,  42),
-	MSM_GPIO_BANK(MSM7X00, 2,  43,  67),
-	MSM_GPIO_BANK(MSM7X00, 3,  68,  94),
-	MSM_GPIO_BANK(MSM7X00, 4,  95, 106),
-	MSM_GPIO_BANK(MSM7X00, 5, 107, 121),
-};
-
-static struct msm_gpio_initdata msm_gpio_7x01_init = {
-	.chips = msm_gpio_chips_msm7x01,
-	.count = ARRAY_SIZE(msm_gpio_chips_msm7x01),
-};
-
-static struct msm_gpio_chip msm_gpio_chips_msm7x30[] = {
-	MSM_GPIO_BANK(MSM7X30, 0,   0,  15),
-	MSM_GPIO_BANK(MSM7X30, 1,  16,  43),
-	MSM_GPIO_BANK(MSM7X30, 2,  44,  67),
-	MSM_GPIO_BANK(MSM7X30, 3,  68,  94),
-	MSM_GPIO_BANK(MSM7X30, 4,  95, 106),
-	MSM_GPIO_BANK(MSM7X30, 5, 107, 133),
-	MSM_GPIO_BANK(MSM7X30, 6, 134, 150),
-	MSM_GPIO_BANK(MSM7X30, 7, 151, 181),
-};
-
-static struct msm_gpio_initdata msm_gpio_7x30_init = {
-	.chips = msm_gpio_chips_msm7x30,
-	.count = ARRAY_SIZE(msm_gpio_chips_msm7x30),
-};
-
-static struct msm_gpio_chip msm_gpio_chips_qsd8x50[] = {
-	MSM_GPIO_BANK(QSD8X50, 0,   0,  15),
-	MSM_GPIO_BANK(QSD8X50, 1,  16,  42),
-	MSM_GPIO_BANK(QSD8X50, 2,  43,  67),
-	MSM_GPIO_BANK(QSD8X50, 3,  68,  94),
-	MSM_GPIO_BANK(QSD8X50, 4,  95, 103),
-	MSM_GPIO_BANK(QSD8X50, 5, 104, 121),
-	MSM_GPIO_BANK(QSD8X50, 6, 122, 152),
-	MSM_GPIO_BANK(QSD8X50, 7, 153, 164),
-};
-
-static struct msm_gpio_initdata msm_gpio_8x50_init = {
-	.chips = msm_gpio_chips_qsd8x50,
-	.count = ARRAY_SIZE(msm_gpio_chips_qsd8x50),
-};
-
-static void msm_gpio_irq_ack(struct irq_data *d)
-{
-	unsigned long irq_flags;
-	struct msm_gpio_chip *msm_chip = irq_data_get_irq_chip_data(d);
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	msm_gpio_clear_detect_status(msm_chip,
-				     d->irq - gpio_to_irq(msm_chip->chip.base));
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-}
-
-static void msm_gpio_irq_mask(struct irq_data *d)
-{
-	unsigned long irq_flags;
-	struct msm_gpio_chip *msm_chip = irq_data_get_irq_chip_data(d);
-	unsigned offset = d->irq - gpio_to_irq(msm_chip->chip.base);
-
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	/* level triggered interrupts are also latched */
-	if (!(msm_gpio_readl(msm_chip, MSM_GPIO_INT_EDGE) & BIT(offset)))
-		msm_gpio_clear_detect_status(msm_chip, offset);
-	msm_chip->int_enable[0] &= ~BIT(offset);
-	msm_gpio_writel(msm_chip, msm_chip->int_enable[0], MSM_GPIO_INT_EN);
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-}
-
-static void msm_gpio_irq_unmask(struct irq_data *d)
-{
-	unsigned long irq_flags;
-	struct msm_gpio_chip *msm_chip = irq_data_get_irq_chip_data(d);
-	unsigned offset = d->irq - gpio_to_irq(msm_chip->chip.base);
-
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	/* level triggered interrupts are also latched */
-	if (!(msm_gpio_readl(msm_chip, MSM_GPIO_INT_EDGE) & BIT(offset)))
-		msm_gpio_clear_detect_status(msm_chip, offset);
-	msm_chip->int_enable[0] |= BIT(offset);
-	msm_gpio_writel(msm_chip, msm_chip->int_enable[0], MSM_GPIO_INT_EN);
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-}
-
-static int msm_gpio_irq_set_wake(struct irq_data *d, unsigned int on)
-{
-	unsigned long irq_flags;
-	struct msm_gpio_chip *msm_chip = irq_data_get_irq_chip_data(d);
-	unsigned offset = d->irq - gpio_to_irq(msm_chip->chip.base);
-
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-
-	if (on)
-		msm_chip->int_enable[1] |= BIT(offset);
-	else
-		msm_chip->int_enable[1] &= ~BIT(offset);
-
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-	return 0;
-}
-
-static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int flow_type)
-{
-	unsigned long irq_flags;
-	struct msm_gpio_chip *msm_chip = irq_data_get_irq_chip_data(d);
-	unsigned offset = d->irq - gpio_to_irq(msm_chip->chip.base);
-	unsigned val, mask = BIT(offset);
-
-	spin_lock_irqsave(&msm_chip->lock, irq_flags);
-	val = msm_gpio_readl(msm_chip, MSM_GPIO_INT_EDGE);
-	if (flow_type & IRQ_TYPE_EDGE_BOTH) {
-		msm_gpio_writel(msm_chip, val | mask, MSM_GPIO_INT_EDGE);
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
-	} else {
-		msm_gpio_writel(msm_chip, val & ~mask, MSM_GPIO_INT_EDGE);
-		__irq_set_handler_locked(d->irq, handle_level_irq);
-	}
-	if ((flow_type & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) {
-		msm_chip->both_edge_detect |= mask;
-		msm_gpio_update_both_edge_detect(msm_chip);
-	} else {
-		msm_chip->both_edge_detect &= ~mask;
-		val = msm_gpio_readl(msm_chip, MSM_GPIO_INT_POS);
-		if (flow_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_HIGH))
-			val |= mask;
-		else
-			val &= ~mask;
-		msm_gpio_writel(msm_chip, val, MSM_GPIO_INT_POS);
-	}
-	spin_unlock_irqrestore(&msm_chip->lock, irq_flags);
-	return 0;
-}
-
-static void msm_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	int i, j, mask;
-	unsigned val;
-
-	for (i = 0; i < msm_gpio_count; i++) {
-		struct msm_gpio_chip *msm_chip = &msm_gpio_chips[i];
-		val = msm_gpio_readl(msm_chip, MSM_GPIO_INT_STATUS);
-		val &= msm_chip->int_enable[0];
-		while (val) {
-			mask = val & -val;
-			j = fls(mask) - 1;
-			/* printk("%s %08x %08x bit %d gpio %d irq %d\n",
-				__func__, v, m, j, msm_chip->chip.start + j,
-				FIRST_GPIO_IRQ + msm_chip->chip.start + j); */
-			val &= ~mask;
-			generic_handle_irq(FIRST_GPIO_IRQ +
-					   msm_chip->chip.base + j);
-		}
-	}
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-}
-
-static struct irq_chip msm_gpio_irq_chip = {
-	.name          = "msmgpio",
-	.irq_ack       = msm_gpio_irq_ack,
-	.irq_mask      = msm_gpio_irq_mask,
-	.irq_unmask    = msm_gpio_irq_unmask,
-	.irq_set_wake  = msm_gpio_irq_set_wake,
-	.irq_set_type  = msm_gpio_irq_set_type,
-};
-
-static int gpio_msm_v1_probe(struct platform_device *pdev)
-{
-	int i, j = 0;
-	const struct platform_device_id *dev_id = platform_get_device_id(pdev);
-	struct msm_gpio_initdata *data;
-	int irq1, irq2;
-	struct resource *res;
-	void __iomem *base1, __iomem *base2;
-
-	data = (struct msm_gpio_initdata *)dev_id->driver_data;
-	msm_gpio_chips = data->chips;
-	msm_gpio_count = data->count;
-
-	irq1 = platform_get_irq(pdev, 0);
-	if (irq1 < 0)
-		return irq1;
-
-	irq2 = platform_get_irq(pdev, 1);
-	if (irq2 < 0)
-		return irq2;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	base1 = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(base1))
-		return PTR_ERR(base1);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-	base2 = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(base2))
-		return PTR_ERR(base2);
-
-	for (i = FIRST_GPIO_IRQ; i < FIRST_GPIO_IRQ + NR_GPIO_IRQS; i++) {
-		if (i - FIRST_GPIO_IRQ >=
-			msm_gpio_chips[j].chip.base +
-			msm_gpio_chips[j].chip.ngpio)
-			j++;
-		irq_set_chip_data(i, &msm_gpio_chips[j]);
-		irq_set_chip_and_handler(i, &msm_gpio_irq_chip,
-					 handle_edge_irq);
-		set_irq_flags(i, IRQF_VALID);
-	}
-
-	for (i = 0; i < msm_gpio_count; i++) {
-		if (i == 1)
-			msm_gpio_chips[i].base = base2;
-		else
-			msm_gpio_chips[i].base = base1;
-		spin_lock_init(&msm_gpio_chips[i].lock);
-		msm_gpio_writel(&msm_gpio_chips[i], 0, MSM_GPIO_INT_EN);
-		gpiochip_add(&msm_gpio_chips[i].chip);
-	}
-
-	irq_set_chained_handler(irq1, msm_gpio_irq_handler);
-	irq_set_chained_handler(irq2, msm_gpio_irq_handler);
-	irq_set_irq_wake(irq1, 1);
-	irq_set_irq_wake(irq2, 1);
-	return 0;
-}
-
-static struct platform_device_id gpio_msm_v1_device_ids[] = {
-	{ "gpio-msm-7201", (unsigned long)&msm_gpio_7x01_init },
-	{ "gpio-msm-7x30", (unsigned long)&msm_gpio_7x30_init },
-	{ "gpio-msm-8x50", (unsigned long)&msm_gpio_8x50_init },
-	{ }
-};
-MODULE_DEVICE_TABLE(platform, gpio_msm_v1_device_ids);
-
-static struct platform_driver gpio_msm_v1_driver = {
-	.driver = {
-		.name = "gpio-msm-v1",
-	},
-	.probe = gpio_msm_v1_probe,
-	.id_table = gpio_msm_v1_device_ids,
-};
-
-static int __init gpio_msm_v1_init(void)
-{
-	return platform_driver_register(&gpio_msm_v1_driver);
-}
-postcore_initcall(gpio_msm_v1_init);
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 7f4db90..b1f837e 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -408,14 +408,6 @@
 
 	  If unsure, say N.
 
-config MMC_MSM
-	tristate "Qualcomm SDCC Controller Support"
-	depends on MMC && (ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50)
-	help
-	  This provides support for the SD/MMC cell found in the
-	  MSM and QSD SOCs from Qualcomm. The controller also has
-	  support for SDIO devices.
-
 config MMC_MXC
 	tristate "Freescale i.MX21/27/31 or MPC512x Multimedia Card support"
 	depends on ARCH_MXC || PPC_MPC512x
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 711e913..e3ab5b9 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -24,7 +24,6 @@
 obj-$(CONFIG_MMC_OMAP_HS)	+= omap_hsmmc.o
 obj-$(CONFIG_MMC_ATMELMCI)	+= atmel-mci.o
 obj-$(CONFIG_MMC_TIFM_SD)	+= tifm_sd.o
-obj-$(CONFIG_MMC_MSM)		+= msm_sdcc.o
 obj-$(CONFIG_MMC_MVSDIO)	+= mvsdio.o
 obj-$(CONFIG_MMC_DAVINCI)       += davinci_mmc.o
 obj-$(CONFIG_MMC_GOLDFISH)	+= android-goldfish.o
diff --git a/drivers/mmc/host/msm_sdcc.c b/drivers/mmc/host/msm_sdcc.c
deleted file mode 100644
index 90c60fd..0000000
--- a/drivers/mmc/host/msm_sdcc.c
+++ /dev/null
@@ -1,1474 +0,0 @@
-/*
- *  linux/drivers/mmc/host/msm_sdcc.c - Qualcomm MSM 7X00A SDCC Driver
- *
- *  Copyright (C) 2007 Google Inc,
- *  Copyright (C) 2003 Deep Blue Solutions, Ltd, All Rights Reserved.
- *  Copyright (C) 2009, Code Aurora Forum. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Based on mmci.c
- *
- * Author: San Mehat (san@android.com)
- *
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/highmem.h>
-#include <linux/log2.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/card.h>
-#include <linux/mmc/sdio.h>
-#include <linux/clk.h>
-#include <linux/scatterlist.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/debugfs.h>
-#include <linux/io.h>
-#include <linux/memory.h>
-#include <linux/gfp.h>
-#include <linux/gpio.h>
-
-#include <asm/cacheflush.h>
-#include <asm/div64.h>
-#include <asm/sizes.h>
-
-#include <linux/platform_data/mmc-msm_sdcc.h>
-#include <mach/dma.h>
-#include <mach/clk.h>
-
-#include "msm_sdcc.h"
-
-#define DRIVER_NAME "msm-sdcc"
-
-#define BUSCLK_PWRSAVE 1
-#define BUSCLK_TIMEOUT (HZ)
-static unsigned int msmsdcc_fmin = 144000;
-static unsigned int msmsdcc_fmax = 50000000;
-static unsigned int msmsdcc_4bit = 1;
-static unsigned int msmsdcc_pwrsave = 1;
-static unsigned int msmsdcc_piopoll = 1;
-static unsigned int msmsdcc_sdioirq;
-
-#define PIO_SPINMAX 30
-#define CMD_SPINMAX 20
-
-
-static inline void
-msmsdcc_disable_clocks(struct msmsdcc_host *host, int deferr)
-{
-	WARN_ON(!host->clks_on);
-
-	BUG_ON(host->curr.mrq);
-
-	if (deferr) {
-		mod_timer(&host->busclk_timer, jiffies + BUSCLK_TIMEOUT);
-	} else {
-		del_timer_sync(&host->busclk_timer);
-		/* Need to check clks_on again in case the busclk
-		 * timer fired
-		 */
-		if (host->clks_on) {
-			clk_disable(host->clk);
-			clk_disable(host->pclk);
-			host->clks_on = 0;
-		}
-	}
-}
-
-static inline int
-msmsdcc_enable_clocks(struct msmsdcc_host *host)
-{
-	int rc;
-
-	del_timer_sync(&host->busclk_timer);
-
-	if (!host->clks_on) {
-		rc = clk_enable(host->pclk);
-		if (rc)
-			return rc;
-		rc = clk_enable(host->clk);
-		if (rc) {
-			clk_disable(host->pclk);
-			return rc;
-		}
-		udelay(1 + ((3 * USEC_PER_SEC) /
-		       (host->clk_rate ? host->clk_rate : msmsdcc_fmin)));
-		host->clks_on = 1;
-	}
-	return 0;
-}
-
-static inline unsigned int
-msmsdcc_readl(struct msmsdcc_host *host, unsigned int reg)
-{
-	return readl(host->base + reg);
-}
-
-static inline void
-msmsdcc_writel(struct msmsdcc_host *host, u32 data, unsigned int reg)
-{
-	writel(data, host->base + reg);
-	/* 3 clk delay required! */
-	udelay(1 + ((3 * USEC_PER_SEC) /
-	       (host->clk_rate ? host->clk_rate : msmsdcc_fmin)));
-}
-
-static void
-msmsdcc_start_command(struct msmsdcc_host *host, struct mmc_command *cmd,
-		      u32 c);
-
-static void msmsdcc_reset_and_restore(struct msmsdcc_host *host)
-{
-	u32	mci_clk = 0;
-	u32	mci_mask0 = 0;
-	int	ret = 0;
-
-	/* Save the controller state */
-	mci_clk = readl(host->base + MMCICLOCK);
-	mci_mask0 = readl(host->base + MMCIMASK0);
-
-	/* Reset the controller */
-	ret = clk_reset(host->clk, CLK_RESET_ASSERT);
-	if (ret)
-		pr_err("%s: Clock assert failed at %u Hz with err %d\n",
-				mmc_hostname(host->mmc), host->clk_rate, ret);
-
-	ret = clk_reset(host->clk, CLK_RESET_DEASSERT);
-	if (ret)
-		pr_err("%s: Clock deassert failed at %u Hz with err %d\n",
-				mmc_hostname(host->mmc), host->clk_rate, ret);
-
-	pr_info("%s: Controller has been re-initialiazed\n",
-			mmc_hostname(host->mmc));
-
-	/* Restore the contoller state */
-	writel(host->pwr, host->base + MMCIPOWER);
-	writel(mci_clk, host->base + MMCICLOCK);
-	writel(mci_mask0, host->base + MMCIMASK0);
-	ret = clk_set_rate(host->clk, host->clk_rate);
-	if (ret)
-		pr_err("%s: Failed to set clk rate %u Hz (%d)\n",
-				mmc_hostname(host->mmc), host->clk_rate, ret);
-}
-
-static void
-msmsdcc_request_end(struct msmsdcc_host *host, struct mmc_request *mrq)
-{
-	BUG_ON(host->curr.data);
-
-	host->curr.mrq = NULL;
-	host->curr.cmd = NULL;
-
-	if (mrq->data)
-		mrq->data->bytes_xfered = host->curr.data_xfered;
-	if (mrq->cmd->error == -ETIMEDOUT)
-		mdelay(5);
-
-#if BUSCLK_PWRSAVE
-	msmsdcc_disable_clocks(host, 1);
-#endif
-	/*
-	 * Need to drop the host lock here; mmc_request_done may call
-	 * back into the driver...
-	 */
-	spin_unlock(&host->lock);
-	mmc_request_done(host->mmc, mrq);
-	spin_lock(&host->lock);
-}
-
-static void
-msmsdcc_stop_data(struct msmsdcc_host *host)
-{
-	host->curr.data = NULL;
-	host->curr.got_dataend = 0;
-}
-
-uint32_t msmsdcc_fifo_addr(struct msmsdcc_host *host)
-{
-	return host->memres->start + MMCIFIFO;
-}
-
-static inline void
-msmsdcc_start_command_exec(struct msmsdcc_host *host, u32 arg, u32 c) {
-       msmsdcc_writel(host, arg, MMCIARGUMENT);
-       msmsdcc_writel(host, c, MMCICOMMAND);
-}
-
-static void
-msmsdcc_dma_exec_func(struct msm_dmov_cmd *cmd)
-{
-	struct msmsdcc_host *host = (struct msmsdcc_host *)cmd->data;
-
-	msmsdcc_writel(host, host->cmd_timeout, MMCIDATATIMER);
-	msmsdcc_writel(host, (unsigned int)host->curr.xfer_size,
-		       MMCIDATALENGTH);
-	msmsdcc_writel(host, (msmsdcc_readl(host, MMCIMASK0) &
-			(~MCI_IRQ_PIO)) | host->cmd_pio_irqmask, MMCIMASK0);
-	msmsdcc_writel(host, host->cmd_datactrl, MMCIDATACTRL);
-
-	if (host->cmd_cmd) {
-		msmsdcc_start_command_exec(host,
-					   (u32) host->cmd_cmd->arg,
-					   (u32) host->cmd_c);
-	}
-	host->dma.active = 1;
-}
-
-static void
-msmsdcc_dma_complete_tlet(unsigned long data)
-{
-	struct msmsdcc_host *host = (struct msmsdcc_host *)data;
-	unsigned long		flags;
-	struct mmc_request	*mrq;
-	struct msm_dmov_errdata err;
-
-	spin_lock_irqsave(&host->lock, flags);
-	host->dma.active = 0;
-
-	err = host->dma.err;
-	mrq = host->curr.mrq;
-	BUG_ON(!mrq);
-	WARN_ON(!mrq->data);
-
-	if (!(host->dma.result & DMOV_RSLT_VALID)) {
-		pr_err("msmsdcc: Invalid DataMover result\n");
-		goto out;
-	}
-
-	if (host->dma.result & DMOV_RSLT_DONE) {
-		host->curr.data_xfered = host->curr.xfer_size;
-	} else {
-		/* Error or flush  */
-		if (host->dma.result & DMOV_RSLT_ERROR)
-			pr_err("%s: DMA error (0x%.8x)\n",
-			       mmc_hostname(host->mmc), host->dma.result);
-		if (host->dma.result & DMOV_RSLT_FLUSH)
-			pr_err("%s: DMA channel flushed (0x%.8x)\n",
-			       mmc_hostname(host->mmc), host->dma.result);
-
-		pr_err("Flush data: %.8x %.8x %.8x %.8x %.8x %.8x\n",
-		       err.flush[0], err.flush[1], err.flush[2],
-		       err.flush[3], err.flush[4], err.flush[5]);
-
-		msmsdcc_reset_and_restore(host);
-		if (!mrq->data->error)
-			mrq->data->error = -EIO;
-	}
-	dma_unmap_sg(mmc_dev(host->mmc), host->dma.sg, host->dma.num_ents,
-		     host->dma.dir);
-
-	host->dma.sg = NULL;
-	host->dma.busy = 0;
-
-	if (host->curr.got_dataend || mrq->data->error) {
-
-		/*
-		 * If we've already gotten our DATAEND / DATABLKEND
-		 * for this request, then complete it through here.
-		 */
-		msmsdcc_stop_data(host);
-
-		if (!mrq->data->error)
-			host->curr.data_xfered = host->curr.xfer_size;
-		if (!mrq->data->stop || mrq->cmd->error) {
-			host->curr.mrq = NULL;
-			host->curr.cmd = NULL;
-			mrq->data->bytes_xfered = host->curr.data_xfered;
-
-			spin_unlock_irqrestore(&host->lock, flags);
-#if BUSCLK_PWRSAVE
-			msmsdcc_disable_clocks(host, 1);
-#endif
-			mmc_request_done(host->mmc, mrq);
-			return;
-		} else
-			msmsdcc_start_command(host, mrq->data->stop, 0);
-	}
-
-out:
-	spin_unlock_irqrestore(&host->lock, flags);
-	return;
-}
-
-static void
-msmsdcc_dma_complete_func(struct msm_dmov_cmd *cmd,
-			  unsigned int result,
-			  struct msm_dmov_errdata *err)
-{
-	struct msmsdcc_dma_data	*dma_data =
-		container_of(cmd, struct msmsdcc_dma_data, hdr);
-	struct msmsdcc_host *host = dma_data->host;
-
-	dma_data->result = result;
-	if (err)
-		memcpy(&dma_data->err, err, sizeof(struct msm_dmov_errdata));
-
-	tasklet_schedule(&host->dma_tlet);
-}
-
-static int validate_dma(struct msmsdcc_host *host, struct mmc_data *data)
-{
-	if (host->dma.channel == -1)
-		return -ENOENT;
-
-	if ((data->blksz * data->blocks) < MCI_FIFOSIZE)
-		return -EINVAL;
-	if ((data->blksz * data->blocks) % MCI_FIFOSIZE)
-		return -EINVAL;
-	return 0;
-}
-
-static int msmsdcc_config_dma(struct msmsdcc_host *host, struct mmc_data *data)
-{
-	struct msmsdcc_nc_dmadata *nc;
-	dmov_box *box;
-	uint32_t rows;
-	uint32_t crci;
-	unsigned int n;
-	int i, rc;
-	struct scatterlist *sg = data->sg;
-
-	rc = validate_dma(host, data);
-	if (rc)
-		return rc;
-
-	host->dma.sg = data->sg;
-	host->dma.num_ents = data->sg_len;
-
-       BUG_ON(host->dma.num_ents > NR_SG); /* Prevent memory corruption */
-
-	nc = host->dma.nc;
-
-	switch (host->pdev_id) {
-	case 1:
-		crci = MSMSDCC_CRCI_SDC1;
-		break;
-	case 2:
-		crci = MSMSDCC_CRCI_SDC2;
-		break;
-	case 3:
-		crci = MSMSDCC_CRCI_SDC3;
-		break;
-	case 4:
-		crci = MSMSDCC_CRCI_SDC4;
-		break;
-	default:
-		host->dma.sg = NULL;
-		host->dma.num_ents = 0;
-		return -ENOENT;
-	}
-
-	if (data->flags & MMC_DATA_READ)
-		host->dma.dir = DMA_FROM_DEVICE;
-	else
-		host->dma.dir = DMA_TO_DEVICE;
-
-	host->curr.user_pages = 0;
-
-	box = &nc->cmd[0];
-
-	/* location of command block must be 64 bit aligned */
-	BUG_ON(host->dma.cmd_busaddr & 0x07);
-
-	nc->cmdptr = (host->dma.cmd_busaddr >> 3) | CMD_PTR_LP;
-	host->dma.hdr.cmdptr = DMOV_CMD_PTR_LIST |
-			       DMOV_CMD_ADDR(host->dma.cmdptr_busaddr);
-	host->dma.hdr.complete_func = msmsdcc_dma_complete_func;
-
-	n = dma_map_sg(mmc_dev(host->mmc), host->dma.sg,
-			host->dma.num_ents, host->dma.dir);
-	if (n == 0) {
-		pr_err("%s: Unable to map in all sg elements\n",
-			mmc_hostname(host->mmc));
-		host->dma.sg = NULL;
-		host->dma.num_ents = 0;
-		return -ENOMEM;
-	}
-
-	for_each_sg(host->dma.sg, sg, n, i) {
-
-		box->cmd = CMD_MODE_BOX;
-
-		if (i == n - 1)
-			box->cmd |= CMD_LC;
-		rows = (sg_dma_len(sg) % MCI_FIFOSIZE) ?
-			(sg_dma_len(sg) / MCI_FIFOSIZE) + 1 :
-			(sg_dma_len(sg) / MCI_FIFOSIZE) ;
-
-		if (data->flags & MMC_DATA_READ) {
-			box->src_row_addr = msmsdcc_fifo_addr(host);
-			box->dst_row_addr = sg_dma_address(sg);
-
-			box->src_dst_len = (MCI_FIFOSIZE << 16) |
-					   (MCI_FIFOSIZE);
-			box->row_offset = MCI_FIFOSIZE;
-
-			box->num_rows = rows * ((1 << 16) + 1);
-			box->cmd |= CMD_SRC_CRCI(crci);
-		} else {
-			box->src_row_addr = sg_dma_address(sg);
-			box->dst_row_addr = msmsdcc_fifo_addr(host);
-
-			box->src_dst_len = (MCI_FIFOSIZE << 16) |
-					   (MCI_FIFOSIZE);
-			box->row_offset = (MCI_FIFOSIZE << 16);
-
-			box->num_rows = rows * ((1 << 16) + 1);
-			box->cmd |= CMD_DST_CRCI(crci);
-		}
-		box++;
-	}
-
-	return 0;
-}
-
-static int
-snoop_cccr_abort(struct mmc_command *cmd)
-{
-	if ((cmd->opcode == 52) &&
-	    (cmd->arg & 0x80000000) &&
-	    (((cmd->arg >> 9) & 0x1ffff) == SDIO_CCCR_ABORT))
-		return 1;
-	return 0;
-}
-
-static void
-msmsdcc_start_command_deferred(struct msmsdcc_host *host,
-				struct mmc_command *cmd, u32 *c)
-{
-	*c |= (cmd->opcode | MCI_CPSM_ENABLE);
-
-	if (cmd->flags & MMC_RSP_PRESENT) {
-		if (cmd->flags & MMC_RSP_136)
-			*c |= MCI_CPSM_LONGRSP;
-		*c |= MCI_CPSM_RESPONSE;
-	}
-
-	if (/*interrupt*/0)
-		*c |= MCI_CPSM_INTERRUPT;
-
-	if ((((cmd->opcode == 17) || (cmd->opcode == 18))  ||
-	     ((cmd->opcode == 24) || (cmd->opcode == 25))) ||
-	      (cmd->opcode == 53))
-		*c |= MCI_CSPM_DATCMD;
-
-	if (host->prog_scan && (cmd->opcode == 12)) {
-		*c |= MCI_CPSM_PROGENA;
-		host->prog_enable = true;
-	}
-
-	if (cmd == cmd->mrq->stop)
-		*c |= MCI_CSPM_MCIABORT;
-
-	if (snoop_cccr_abort(cmd))
-		*c |= MCI_CSPM_MCIABORT;
-
-	if (host->curr.cmd != NULL) {
-		pr_err("%s: Overlapping command requests\n",
-			mmc_hostname(host->mmc));
-	}
-	host->curr.cmd = cmd;
-}
-
-static void
-msmsdcc_start_data(struct msmsdcc_host *host, struct mmc_data *data,
-			struct mmc_command *cmd, u32 c)
-{
-	unsigned int datactrl, timeout;
-	unsigned long long clks;
-	unsigned int pio_irqmask = 0;
-
-	host->curr.data = data;
-	host->curr.xfer_size = data->blksz * data->blocks;
-	host->curr.xfer_remain = host->curr.xfer_size;
-	host->curr.data_xfered = 0;
-	host->curr.got_dataend = 0;
-
-	memset(&host->pio, 0, sizeof(host->pio));
-
-	datactrl = MCI_DPSM_ENABLE | (data->blksz << 4);
-
-	if (!msmsdcc_config_dma(host, data))
-		datactrl |= MCI_DPSM_DMAENABLE;
-	else {
-		host->pio.sg = data->sg;
-		host->pio.sg_len = data->sg_len;
-		host->pio.sg_off = 0;
-
-		if (data->flags & MMC_DATA_READ) {
-			pio_irqmask = MCI_RXFIFOHALFFULLMASK;
-			if (host->curr.xfer_remain < MCI_FIFOSIZE)
-				pio_irqmask |= MCI_RXDATAAVLBLMASK;
-		} else
-			pio_irqmask = MCI_TXFIFOHALFEMPTYMASK;
-	}
-
-	if (data->flags & MMC_DATA_READ)
-		datactrl |= MCI_DPSM_DIRECTION;
-
-	clks = (unsigned long long)data->timeout_ns * host->clk_rate;
-	do_div(clks, NSEC_PER_SEC);
-	timeout = data->timeout_clks + (unsigned int)clks*2 ;
-
-	if (datactrl & MCI_DPSM_DMAENABLE) {
-		/* Save parameters for the exec function */
-		host->cmd_timeout = timeout;
-		host->cmd_pio_irqmask = pio_irqmask;
-		host->cmd_datactrl = datactrl;
-		host->cmd_cmd = cmd;
-
-		host->dma.hdr.execute_func = msmsdcc_dma_exec_func;
-		host->dma.hdr.data = (void *)host;
-		host->dma.busy = 1;
-
-		if (cmd) {
-			msmsdcc_start_command_deferred(host, cmd, &c);
-			host->cmd_c = c;
-		}
-		msm_dmov_enqueue_cmd(host->dma.channel, &host->dma.hdr);
-		if (data->flags & MMC_DATA_WRITE)
-			host->prog_scan = true;
-	} else {
-		msmsdcc_writel(host, timeout, MMCIDATATIMER);
-
-		msmsdcc_writel(host, host->curr.xfer_size, MMCIDATALENGTH);
-
-		msmsdcc_writel(host, (msmsdcc_readl(host, MMCIMASK0) &
-				(~MCI_IRQ_PIO)) | pio_irqmask, MMCIMASK0);
-
-		msmsdcc_writel(host, datactrl, MMCIDATACTRL);
-
-		if (cmd) {
-			/* Daisy-chain the command if requested */
-			msmsdcc_start_command(host, cmd, c);
-		}
-	}
-}
-
-static void
-msmsdcc_start_command(struct msmsdcc_host *host, struct mmc_command *cmd, u32 c)
-{
-	if (cmd == cmd->mrq->stop)
-		c |= MCI_CSPM_MCIABORT;
-
-	host->stats.cmds++;
-
-	msmsdcc_start_command_deferred(host, cmd, &c);
-	msmsdcc_start_command_exec(host, cmd->arg, c);
-}
-
-static void
-msmsdcc_data_err(struct msmsdcc_host *host, struct mmc_data *data,
-		 unsigned int status)
-{
-	if (status & MCI_DATACRCFAIL) {
-		pr_err("%s: Data CRC error\n", mmc_hostname(host->mmc));
-		pr_err("%s: opcode 0x%.8x\n", __func__,
-		       data->mrq->cmd->opcode);
-		pr_err("%s: blksz %d, blocks %d\n", __func__,
-		       data->blksz, data->blocks);
-		data->error = -EILSEQ;
-	} else if (status & MCI_DATATIMEOUT) {
-		pr_err("%s: Data timeout\n", mmc_hostname(host->mmc));
-		data->error = -ETIMEDOUT;
-	} else if (status & MCI_RXOVERRUN) {
-		pr_err("%s: RX overrun\n", mmc_hostname(host->mmc));
-		data->error = -EIO;
-	} else if (status & MCI_TXUNDERRUN) {
-		pr_err("%s: TX underrun\n", mmc_hostname(host->mmc));
-		data->error = -EIO;
-	} else {
-		pr_err("%s: Unknown error (0x%.8x)\n",
-		       mmc_hostname(host->mmc), status);
-		data->error = -EIO;
-	}
-}
-
-
-static int
-msmsdcc_pio_read(struct msmsdcc_host *host, char *buffer, unsigned int remain)
-{
-	uint32_t	*ptr = (uint32_t *) buffer;
-	int		count = 0;
-
-	if (remain % 4)
-		remain = ((remain >> 2) + 1) << 2;
-
-	while (msmsdcc_readl(host, MMCISTATUS) & MCI_RXDATAAVLBL) {
-		*ptr = msmsdcc_readl(host, MMCIFIFO + (count % MCI_FIFOSIZE));
-		ptr++;
-		count += sizeof(uint32_t);
-
-		remain -=  sizeof(uint32_t);
-		if (remain == 0)
-			break;
-	}
-	return count;
-}
-
-static int
-msmsdcc_pio_write(struct msmsdcc_host *host, char *buffer,
-		  unsigned int remain, u32 status)
-{
-	void __iomem *base = host->base;
-	char *ptr = buffer;
-
-	do {
-		unsigned int count, maxcnt, sz;
-
-		maxcnt = status & MCI_TXFIFOEMPTY ? MCI_FIFOSIZE :
-						    MCI_FIFOHALFSIZE;
-		count = min(remain, maxcnt);
-
-		sz = count % 4 ? (count >> 2) + 1 : (count >> 2);
-		writesl(base + MMCIFIFO, ptr, sz);
-		ptr += count;
-		remain -= count;
-
-		if (remain == 0)
-			break;
-
-		status = msmsdcc_readl(host, MMCISTATUS);
-	} while (status & MCI_TXFIFOHALFEMPTY);
-
-	return ptr - buffer;
-}
-
-static int
-msmsdcc_spin_on_status(struct msmsdcc_host *host, uint32_t mask, int maxspin)
-{
-	while (maxspin) {
-		if ((msmsdcc_readl(host, MMCISTATUS) & mask))
-			return 0;
-		udelay(1);
-		--maxspin;
-	}
-	return -ETIMEDOUT;
-}
-
-static irqreturn_t
-msmsdcc_pio_irq(int irq, void *dev_id)
-{
-	struct msmsdcc_host	*host = dev_id;
-	uint32_t		status;
-	u32 mci_mask0;
-
-	status = msmsdcc_readl(host, MMCISTATUS);
-	mci_mask0 = msmsdcc_readl(host, MMCIMASK0);
-
-	if (((mci_mask0 & status) & MCI_IRQ_PIO) == 0)
-		return IRQ_NONE;
-
-	do {
-		unsigned long flags;
-		unsigned int remain, len;
-		char *buffer;
-
-		if (!(status & (MCI_TXFIFOHALFEMPTY | MCI_RXDATAAVLBL))) {
-			if (host->curr.xfer_remain == 0 || !msmsdcc_piopoll)
-				break;
-
-			if (msmsdcc_spin_on_status(host,
-						   (MCI_TXFIFOHALFEMPTY |
-						   MCI_RXDATAAVLBL),
-						   PIO_SPINMAX)) {
-				break;
-			}
-		}
-
-		/* Map the current scatter buffer */
-		local_irq_save(flags);
-		buffer = kmap_atomic(sg_page(host->pio.sg))
-				     + host->pio.sg->offset;
-		buffer += host->pio.sg_off;
-		remain = host->pio.sg->length - host->pio.sg_off;
-		len = 0;
-		if (status & MCI_RXACTIVE)
-			len = msmsdcc_pio_read(host, buffer, remain);
-		if (status & MCI_TXACTIVE)
-			len = msmsdcc_pio_write(host, buffer, remain, status);
-
-		/* Unmap the buffer */
-		kunmap_atomic(buffer);
-		local_irq_restore(flags);
-
-		host->pio.sg_off += len;
-		host->curr.xfer_remain -= len;
-		host->curr.data_xfered += len;
-		remain -= len;
-
-		if (remain == 0) {
-			/* This sg page is full - do some housekeeping */
-			if (status & MCI_RXACTIVE && host->curr.user_pages)
-				flush_dcache_page(sg_page(host->pio.sg));
-
-			if (!--host->pio.sg_len) {
-				memset(&host->pio, 0, sizeof(host->pio));
-				break;
-			}
-
-			/* Advance to next sg */
-			host->pio.sg++;
-			host->pio.sg_off = 0;
-		}
-
-		status = msmsdcc_readl(host, MMCISTATUS);
-	} while (1);
-
-	if (status & MCI_RXACTIVE && host->curr.xfer_remain < MCI_FIFOSIZE)
-		msmsdcc_writel(host, (mci_mask0 & (~MCI_IRQ_PIO)) |
-					MCI_RXDATAAVLBLMASK, MMCIMASK0);
-
-	if (!host->curr.xfer_remain)
-		msmsdcc_writel(host, (mci_mask0 & (~MCI_IRQ_PIO)) | 0,
-					MMCIMASK0);
-
-	return IRQ_HANDLED;
-}
-
-static void msmsdcc_do_cmdirq(struct msmsdcc_host *host, uint32_t status)
-{
-	struct mmc_command *cmd = host->curr.cmd;
-
-	host->curr.cmd = NULL;
-	cmd->resp[0] = msmsdcc_readl(host, MMCIRESPONSE0);
-	cmd->resp[1] = msmsdcc_readl(host, MMCIRESPONSE1);
-	cmd->resp[2] = msmsdcc_readl(host, MMCIRESPONSE2);
-	cmd->resp[3] = msmsdcc_readl(host, MMCIRESPONSE3);
-
-	if (status & MCI_CMDTIMEOUT) {
-		cmd->error = -ETIMEDOUT;
-	} else if (status & MCI_CMDCRCFAIL &&
-		   cmd->flags & MMC_RSP_CRC) {
-		pr_err("%s: Command CRC error\n", mmc_hostname(host->mmc));
-		cmd->error = -EILSEQ;
-	}
-
-	if (!cmd->data || cmd->error) {
-		if (host->curr.data && host->dma.sg)
-			msm_dmov_stop_cmd(host->dma.channel,
-					  &host->dma.hdr, 0);
-		else if (host->curr.data) { /* Non DMA */
-			msmsdcc_reset_and_restore(host);
-			msmsdcc_stop_data(host);
-			msmsdcc_request_end(host, cmd->mrq);
-		} else { /* host->data == NULL */
-			if (!cmd->error && host->prog_enable) {
-				if (status & MCI_PROGDONE) {
-					host->prog_scan = false;
-					host->prog_enable = false;
-					msmsdcc_request_end(host, cmd->mrq);
-				} else {
-					host->curr.cmd = cmd;
-				}
-			} else {
-				if (host->prog_enable) {
-					host->prog_scan = false;
-					host->prog_enable = false;
-				}
-				msmsdcc_request_end(host, cmd->mrq);
-			}
-		}
-	} else if (cmd->data)
-		if (!(cmd->data->flags & MMC_DATA_READ))
-			msmsdcc_start_data(host, cmd->data,
-						NULL, 0);
-}
-
-static void
-msmsdcc_handle_irq_data(struct msmsdcc_host *host, u32 status,
-			void __iomem *base)
-{
-	struct mmc_data *data = host->curr.data;
-
-	if (status & (MCI_CMDSENT | MCI_CMDRESPEND | MCI_CMDCRCFAIL |
-			MCI_CMDTIMEOUT | MCI_PROGDONE) && host->curr.cmd) {
-		msmsdcc_do_cmdirq(host, status);
-	}
-
-	if (!data)
-		return;
-
-	/* Check for data errors */
-	if (status & (MCI_DATACRCFAIL | MCI_DATATIMEOUT |
-		      MCI_TXUNDERRUN | MCI_RXOVERRUN)) {
-		msmsdcc_data_err(host, data, status);
-		host->curr.data_xfered = 0;
-		if (host->dma.sg)
-			msm_dmov_stop_cmd(host->dma.channel,
-					  &host->dma.hdr, 0);
-		else {
-			msmsdcc_reset_and_restore(host);
-			if (host->curr.data)
-				msmsdcc_stop_data(host);
-			if (!data->stop)
-				msmsdcc_request_end(host, data->mrq);
-			else
-				msmsdcc_start_command(host, data->stop, 0);
-		}
-	}
-
-	/* Check for data done */
-	if (!host->curr.got_dataend && (status & MCI_DATAEND))
-		host->curr.got_dataend = 1;
-
-	/*
-	 * If DMA is still in progress, we complete via the completion handler
-	 */
-	if (host->curr.got_dataend && !host->dma.busy) {
-		/*
-		 * There appears to be an issue in the controller where
-		 * if you request a small block transfer (< fifo size),
-		 * you may get your DATAEND/DATABLKEND irq without the
-		 * PIO data irq.
-		 *
-		 * Check to see if there is still data to be read,
-		 * and simulate a PIO irq.
-		 */
-		if (readl(base + MMCISTATUS) & MCI_RXDATAAVLBL)
-			msmsdcc_pio_irq(1, host);
-
-		msmsdcc_stop_data(host);
-		if (!data->error)
-			host->curr.data_xfered = host->curr.xfer_size;
-
-		if (!data->stop)
-			msmsdcc_request_end(host, data->mrq);
-		else
-			msmsdcc_start_command(host, data->stop, 0);
-	}
-}
-
-static irqreturn_t
-msmsdcc_irq(int irq, void *dev_id)
-{
-	struct msmsdcc_host	*host = dev_id;
-	void __iomem		*base = host->base;
-	u32			status;
-	int			ret = 0;
-	int			cardint = 0;
-
-	spin_lock(&host->lock);
-
-	do {
-		status = msmsdcc_readl(host, MMCISTATUS);
-		status &= msmsdcc_readl(host, MMCIMASK0);
-		if ((status & (~MCI_IRQ_PIO)) == 0)
-			break;
-		msmsdcc_writel(host, status, MMCICLEAR);
-
-		if (status & MCI_SDIOINTR)
-			status &= ~MCI_SDIOINTR;
-
-		if (!status)
-			break;
-
-		msmsdcc_handle_irq_data(host, status, base);
-
-		if (status & MCI_SDIOINTOPER) {
-			cardint = 1;
-			status &= ~MCI_SDIOINTOPER;
-		}
-		ret = 1;
-	} while (status);
-
-	spin_unlock(&host->lock);
-
-	/*
-	 * We have to delay handling the card interrupt as it calls
-	 * back into the driver.
-	 */
-	if (cardint)
-		mmc_signal_sdio_irq(host->mmc);
-
-	return IRQ_RETVAL(ret);
-}
-
-static void
-msmsdcc_request(struct mmc_host *mmc, struct mmc_request *mrq)
-{
-	struct msmsdcc_host *host = mmc_priv(mmc);
-	unsigned long flags;
-
-	WARN_ON(host->curr.mrq != NULL);
-	WARN_ON(host->pwr == 0);
-
-	spin_lock_irqsave(&host->lock, flags);
-
-	host->stats.reqs++;
-
-	if (host->eject) {
-		if (mrq->data && !(mrq->data->flags & MMC_DATA_READ)) {
-			mrq->cmd->error = 0;
-			mrq->data->bytes_xfered = mrq->data->blksz *
-						  mrq->data->blocks;
-		} else
-			mrq->cmd->error = -ENOMEDIUM;
-
-		spin_unlock_irqrestore(&host->lock, flags);
-		mmc_request_done(mmc, mrq);
-		return;
-	}
-
-	msmsdcc_enable_clocks(host);
-
-	host->curr.mrq = mrq;
-
-	if (mrq->data && mrq->data->flags & MMC_DATA_READ)
-		/* Queue/read data, daisy-chain command when data starts */
-		msmsdcc_start_data(host, mrq->data, mrq->cmd, 0);
-	else
-		msmsdcc_start_command(host, mrq->cmd, 0);
-
-	if (host->cmdpoll && !msmsdcc_spin_on_status(host,
-				MCI_CMDRESPEND|MCI_CMDCRCFAIL|MCI_CMDTIMEOUT,
-				CMD_SPINMAX)) {
-		uint32_t status = msmsdcc_readl(host, MMCISTATUS);
-		msmsdcc_do_cmdirq(host, status);
-		msmsdcc_writel(host,
-			       MCI_CMDRESPEND | MCI_CMDCRCFAIL | MCI_CMDTIMEOUT,
-			       MMCICLEAR);
-		host->stats.cmdpoll_hits++;
-	} else {
-		host->stats.cmdpoll_misses++;
-	}
-	spin_unlock_irqrestore(&host->lock, flags);
-}
-
-static void msmsdcc_setup_gpio(struct msmsdcc_host *host, bool enable)
-{
-	struct msm_mmc_gpio_data *curr;
-	int i, rc = 0;
-
-	if (!host->plat->gpio_data || host->gpio_config_status == enable)
-		return;
-
-	curr = host->plat->gpio_data;
-	for (i = 0; i < curr->size; i++) {
-		if (enable) {
-			rc = gpio_request(curr->gpio[i].no,
-						curr->gpio[i].name);
-			if (rc) {
-				pr_err("%s: gpio_request(%d, %s) failed %d\n",
-					mmc_hostname(host->mmc),
-					curr->gpio[i].no,
-					curr->gpio[i].name, rc);
-				goto free_gpios;
-			}
-		} else {
-			gpio_free(curr->gpio[i].no);
-		}
-	}
-	host->gpio_config_status = enable;
-	return;
-
-free_gpios:
-	for (; i >= 0; i--)
-		gpio_free(curr->gpio[i].no);
-}
-
-static void
-msmsdcc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
-{
-	struct msmsdcc_host *host = mmc_priv(mmc);
-	u32 clk = 0, pwr = 0;
-	int rc;
-	unsigned long flags;
-
-	spin_lock_irqsave(&host->lock, flags);
-
-	msmsdcc_enable_clocks(host);
-
-	spin_unlock_irqrestore(&host->lock, flags);
-
-	if (ios->clock) {
-		if (ios->clock != host->clk_rate) {
-			rc = clk_set_rate(host->clk, ios->clock);
-			if (rc < 0)
-				pr_err("%s: Error setting clock rate (%d)\n",
-				       mmc_hostname(host->mmc), rc);
-			else
-				host->clk_rate = ios->clock;
-		}
-		clk |= MCI_CLK_ENABLE;
-	}
-
-	if (ios->bus_width == MMC_BUS_WIDTH_4)
-		clk |= (2 << 10); /* Set WIDEBUS */
-
-	if (ios->clock > 400000 && msmsdcc_pwrsave)
-		clk |= (1 << 9); /* PWRSAVE */
-
-	clk |= (1 << 12); /* FLOW_ENA */
-	clk |= (1 << 15); /* feedback clock */
-
-	if (host->plat->translate_vdd)
-		pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
-
-	switch (ios->power_mode) {
-	case MMC_POWER_OFF:
-		msmsdcc_setup_gpio(host, false);
-		break;
-	case MMC_POWER_UP:
-		pwr |= MCI_PWR_UP;
-		msmsdcc_setup_gpio(host, true);
-		break;
-	case MMC_POWER_ON:
-		pwr |= MCI_PWR_ON;
-		break;
-	}
-
-	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
-		pwr |= MCI_OD;
-
-	msmsdcc_writel(host, clk, MMCICLOCK);
-
-	if (host->pwr != pwr) {
-		host->pwr = pwr;
-		msmsdcc_writel(host, pwr, MMCIPOWER);
-	}
-#if BUSCLK_PWRSAVE
-	spin_lock_irqsave(&host->lock, flags);
-	msmsdcc_disable_clocks(host, 1);
-	spin_unlock_irqrestore(&host->lock, flags);
-#endif
-}
-
-static void msmsdcc_enable_sdio_irq(struct mmc_host *mmc, int enable)
-{
-	struct msmsdcc_host *host = mmc_priv(mmc);
-	unsigned long flags;
-	u32 status;
-
-	spin_lock_irqsave(&host->lock, flags);
-	if (msmsdcc_sdioirq == 1) {
-		status = msmsdcc_readl(host, MMCIMASK0);
-		if (enable)
-			status |= MCI_SDIOINTOPERMASK;
-		else
-			status &= ~MCI_SDIOINTOPERMASK;
-		host->saved_irq0mask = status;
-		msmsdcc_writel(host, status, MMCIMASK0);
-	}
-	spin_unlock_irqrestore(&host->lock, flags);
-}
-
-static void msmsdcc_init_card(struct mmc_host *mmc, struct mmc_card *card)
-{
-	struct msmsdcc_host *host = mmc_priv(mmc);
-
-	if (host->plat->init_card)
-		host->plat->init_card(card);
-}
-
-static const struct mmc_host_ops msmsdcc_ops = {
-	.request	= msmsdcc_request,
-	.set_ios	= msmsdcc_set_ios,
-	.enable_sdio_irq = msmsdcc_enable_sdio_irq,
-	.init_card	= msmsdcc_init_card,
-};
-
-static void
-msmsdcc_check_status(unsigned long data)
-{
-	struct msmsdcc_host *host = (struct msmsdcc_host *)data;
-	unsigned int status;
-
-	if (!host->plat->status) {
-		mmc_detect_change(host->mmc, 0);
-		goto out;
-	}
-
-	status = host->plat->status(mmc_dev(host->mmc));
-	host->eject = !status;
-	if (status ^ host->oldstat) {
-		pr_info("%s: Slot status change detected (%d -> %d)\n",
-			mmc_hostname(host->mmc), host->oldstat, status);
-		if (status)
-			mmc_detect_change(host->mmc, (5 * HZ) / 2);
-		else
-			mmc_detect_change(host->mmc, 0);
-	}
-
-	host->oldstat = status;
-
-out:
-	if (host->timer.function)
-		mod_timer(&host->timer, jiffies + HZ);
-}
-
-static irqreturn_t
-msmsdcc_platform_status_irq(int irq, void *dev_id)
-{
-	struct msmsdcc_host *host = dev_id;
-
-	pr_debug("%s: %d\n", __func__, irq);
-	msmsdcc_check_status((unsigned long) host);
-	return IRQ_HANDLED;
-}
-
-static void
-msmsdcc_status_notify_cb(int card_present, void *dev_id)
-{
-	struct msmsdcc_host *host = dev_id;
-
-	pr_debug("%s: card_present %d\n", mmc_hostname(host->mmc),
-	       card_present);
-	msmsdcc_check_status((unsigned long) host);
-}
-
-static void
-msmsdcc_busclk_expired(unsigned long _data)
-{
-	struct msmsdcc_host	*host = (struct msmsdcc_host *) _data;
-
-	if (host->clks_on)
-		msmsdcc_disable_clocks(host, 0);
-}
-
-static int
-msmsdcc_init_dma(struct msmsdcc_host *host)
-{
-	memset(&host->dma, 0, sizeof(struct msmsdcc_dma_data));
-	host->dma.host = host;
-	host->dma.channel = -1;
-
-	if (!host->dmares)
-		return -ENODEV;
-
-	host->dma.nc = dma_alloc_coherent(NULL,
-					  sizeof(struct msmsdcc_nc_dmadata),
-					  &host->dma.nc_busaddr,
-					  GFP_KERNEL);
-	if (host->dma.nc == NULL) {
-		pr_err("Unable to allocate DMA buffer\n");
-		return -ENOMEM;
-	}
-	memset(host->dma.nc, 0x00, sizeof(struct msmsdcc_nc_dmadata));
-	host->dma.cmd_busaddr = host->dma.nc_busaddr;
-	host->dma.cmdptr_busaddr = host->dma.nc_busaddr +
-				offsetof(struct msmsdcc_nc_dmadata, cmdptr);
-	host->dma.channel = host->dmares->start;
-
-	return 0;
-}
-
-static int
-msmsdcc_probe(struct platform_device *pdev)
-{
-	struct msm_mmc_platform_data *plat = pdev->dev.platform_data;
-	struct msmsdcc_host *host;
-	struct mmc_host *mmc;
-	struct resource *cmd_irqres = NULL;
-	struct resource *stat_irqres = NULL;
-	struct resource *memres = NULL;
-	struct resource *dmares = NULL;
-	int ret;
-
-	/* must have platform data */
-	if (!plat) {
-		pr_err("%s: Platform data not available\n", __func__);
-		ret = -EINVAL;
-		goto out;
-	}
-
-	if (pdev->id < 1 || pdev->id > 4)
-		return -EINVAL;
-
-	if (pdev->resource == NULL || pdev->num_resources < 2) {
-		pr_err("%s: Invalid resource\n", __func__);
-		return -ENXIO;
-	}
-
-	memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-	cmd_irqres = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
-						  "cmd_irq");
-	stat_irqres = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
-						   "status_irq");
-
-	if (!cmd_irqres || !memres) {
-		pr_err("%s: Invalid resource\n", __func__);
-		return -ENXIO;
-	}
-
-	/*
-	 * Setup our host structure
-	 */
-
-	mmc = mmc_alloc_host(sizeof(struct msmsdcc_host), &pdev->dev);
-	if (!mmc) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	host = mmc_priv(mmc);
-	host->pdev_id = pdev->id;
-	host->plat = plat;
-	host->mmc = mmc;
-	host->curr.cmd = NULL;
-	init_timer(&host->busclk_timer);
-	host->busclk_timer.data = (unsigned long) host;
-	host->busclk_timer.function = msmsdcc_busclk_expired;
-
-
-	host->cmdpoll = 1;
-
-	host->base = ioremap(memres->start, PAGE_SIZE);
-	if (!host->base) {
-		ret = -ENOMEM;
-		goto host_free;
-	}
-
-	host->cmd_irqres = cmd_irqres;
-	host->memres = memres;
-	host->dmares = dmares;
-	spin_lock_init(&host->lock);
-
-	tasklet_init(&host->dma_tlet, msmsdcc_dma_complete_tlet,
-			(unsigned long)host);
-
-	/*
-	 * Setup DMA
-	 */
-	if (host->dmares) {
-		ret = msmsdcc_init_dma(host);
-		if (ret)
-			goto ioremap_free;
-	} else {
-		host->dma.channel = -1;
-	}
-
-	/* Get our clocks */
-	host->pclk = clk_get(&pdev->dev, "sdc_pclk");
-	if (IS_ERR(host->pclk)) {
-		ret = PTR_ERR(host->pclk);
-		goto dma_free;
-	}
-
-	host->clk = clk_get(&pdev->dev, "sdc_clk");
-	if (IS_ERR(host->clk)) {
-		ret = PTR_ERR(host->clk);
-		goto pclk_put;
-	}
-
-	ret = clk_set_rate(host->clk, msmsdcc_fmin);
-	if (ret) {
-		pr_err("%s: Clock rate set failed (%d)\n", __func__, ret);
-		goto clk_put;
-	}
-
-	ret = clk_prepare(host->pclk);
-	if (ret)
-		goto clk_put;
-
-	ret = clk_prepare(host->clk);
-	if (ret)
-		goto clk_unprepare_p;
-
-	/* Enable clocks */
-	ret = msmsdcc_enable_clocks(host);
-	if (ret)
-		goto clk_unprepare;
-
-	host->pclk_rate = clk_get_rate(host->pclk);
-	host->clk_rate = clk_get_rate(host->clk);
-
-	/*
-	 * Setup MMC host structure
-	 */
-	mmc->ops = &msmsdcc_ops;
-	mmc->f_min = msmsdcc_fmin;
-	mmc->f_max = msmsdcc_fmax;
-	mmc->ocr_avail = plat->ocr_mask;
-
-	if (msmsdcc_4bit)
-		mmc->caps |= MMC_CAP_4_BIT_DATA;
-	if (msmsdcc_sdioirq)
-		mmc->caps |= MMC_CAP_SDIO_IRQ;
-	mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED;
-
-	mmc->max_segs = NR_SG;
-	mmc->max_blk_size = 4096;	/* MCI_DATA_CTL BLOCKSIZE up to 4096 */
-	mmc->max_blk_count = 65536;
-
-	mmc->max_req_size = 33554432;	/* MCI_DATA_LENGTH is 25 bits */
-	mmc->max_seg_size = mmc->max_req_size;
-
-	msmsdcc_writel(host, 0, MMCIMASK0);
-	msmsdcc_writel(host, 0x5e007ff, MMCICLEAR);
-
-	msmsdcc_writel(host, MCI_IRQENABLE, MMCIMASK0);
-	host->saved_irq0mask = MCI_IRQENABLE;
-
-	/*
-	 * Setup card detect change
-	 */
-
-	memset(&host->timer, 0, sizeof(host->timer));
-
-	if (stat_irqres && !(stat_irqres->flags & IORESOURCE_DISABLED)) {
-		unsigned long irqflags = IRQF_SHARED |
-			(stat_irqres->flags & IRQF_TRIGGER_MASK);
-
-		host->stat_irq = stat_irqres->start;
-		ret = request_irq(host->stat_irq,
-				  msmsdcc_platform_status_irq,
-				  irqflags,
-				  DRIVER_NAME " (slot)",
-				  host);
-		if (ret) {
-			pr_err("%s: Unable to get slot IRQ %d (%d)\n",
-			       mmc_hostname(mmc), host->stat_irq, ret);
-			goto clk_disable;
-		}
-	} else if (plat->register_status_notify) {
-		plat->register_status_notify(msmsdcc_status_notify_cb, host);
-	} else if (!plat->status)
-		pr_err("%s: No card detect facilities available\n",
-		       mmc_hostname(mmc));
-	else {
-		init_timer(&host->timer);
-		host->timer.data = (unsigned long)host;
-		host->timer.function = msmsdcc_check_status;
-		host->timer.expires = jiffies + HZ;
-		add_timer(&host->timer);
-	}
-
-	if (plat->status) {
-		host->oldstat = host->plat->status(mmc_dev(host->mmc));
-		host->eject = !host->oldstat;
-	}
-
-	ret = request_irq(cmd_irqres->start, msmsdcc_irq, IRQF_SHARED,
-			  DRIVER_NAME " (cmd)", host);
-	if (ret)
-		goto stat_irq_free;
-
-	ret = request_irq(cmd_irqres->start, msmsdcc_pio_irq, IRQF_SHARED,
-			  DRIVER_NAME " (pio)", host);
-	if (ret)
-		goto cmd_irq_free;
-
-	platform_set_drvdata(pdev, mmc);
-	mmc_add_host(mmc);
-
-	pr_info("%s: Qualcomm MSM SDCC at 0x%016llx irq %d,%d dma %d\n",
-		mmc_hostname(mmc), (unsigned long long)memres->start,
-		(unsigned int) cmd_irqres->start,
-		(unsigned int) host->stat_irq, host->dma.channel);
-	pr_info("%s: 4 bit data mode %s\n", mmc_hostname(mmc),
-		(mmc->caps & MMC_CAP_4_BIT_DATA ? "enabled" : "disabled"));
-	pr_info("%s: MMC clock %u -> %u Hz, PCLK %u Hz\n",
-		mmc_hostname(mmc), msmsdcc_fmin, msmsdcc_fmax, host->pclk_rate);
-	pr_info("%s: Slot eject status = %d\n", mmc_hostname(mmc), host->eject);
-	pr_info("%s: Power save feature enable = %d\n",
-		mmc_hostname(mmc), msmsdcc_pwrsave);
-
-	if (host->dma.channel != -1) {
-		pr_info("%s: DM non-cached buffer at %p, dma_addr 0x%.8x\n",
-			mmc_hostname(mmc), host->dma.nc, host->dma.nc_busaddr);
-		pr_info("%s: DM cmd busaddr 0x%.8x, cmdptr busaddr 0x%.8x\n",
-			mmc_hostname(mmc), host->dma.cmd_busaddr,
-			host->dma.cmdptr_busaddr);
-	} else
-		pr_info("%s: PIO transfer enabled\n", mmc_hostname(mmc));
-	if (host->timer.function)
-		pr_info("%s: Polling status mode enabled\n", mmc_hostname(mmc));
-
-	return 0;
- cmd_irq_free:
-	free_irq(cmd_irqres->start, host);
- stat_irq_free:
-	if (host->stat_irq)
-		free_irq(host->stat_irq, host);
- clk_disable:
-	msmsdcc_disable_clocks(host, 0);
- clk_unprepare:
-	clk_unprepare(host->clk);
- clk_unprepare_p:
-	clk_unprepare(host->pclk);
- clk_put:
-	clk_put(host->clk);
- pclk_put:
-	clk_put(host->pclk);
-dma_free:
-	if (host->dmares)
-		dma_free_coherent(NULL, sizeof(struct msmsdcc_nc_dmadata),
-					host->dma.nc, host->dma.nc_busaddr);
-ioremap_free:
-	tasklet_kill(&host->dma_tlet);
-	iounmap(host->base);
- host_free:
-	mmc_free_host(mmc);
- out:
-	return ret;
-}
-
-#ifdef CONFIG_PM
-static int
-msmsdcc_suspend(struct platform_device *dev, pm_message_t state)
-{
-	struct mmc_host *mmc = platform_get_drvdata(dev);
-
-	if (mmc) {
-		struct msmsdcc_host *host = mmc_priv(mmc);
-
-		if (host->stat_irq)
-			disable_irq(host->stat_irq);
-
-		msmsdcc_writel(host, 0, MMCIMASK0);
-		if (host->clks_on)
-			msmsdcc_disable_clocks(host, 0);
-	}
-	return 0;
-}
-
-static int
-msmsdcc_resume(struct platform_device *dev)
-{
-	struct mmc_host *mmc = platform_get_drvdata(dev);
-
-	if (mmc) {
-		struct msmsdcc_host *host = mmc_priv(mmc);
-
-		msmsdcc_enable_clocks(host);
-
-		msmsdcc_writel(host, host->saved_irq0mask, MMCIMASK0);
-
-		if (host->stat_irq)
-			enable_irq(host->stat_irq);
-#if BUSCLK_PWRSAVE
-		msmsdcc_disable_clocks(host, 1);
-#endif
-	}
-	return 0;
-}
-#else
-#define msmsdcc_suspend	0
-#define msmsdcc_resume 0
-#endif
-
-static struct platform_driver msmsdcc_driver = {
-	.probe		= msmsdcc_probe,
-	.suspend	= msmsdcc_suspend,
-	.resume		= msmsdcc_resume,
-	.driver		= {
-		.name	= "msm_sdcc",
-	},
-};
-
-module_platform_driver(msmsdcc_driver);
-
-MODULE_DESCRIPTION("Qualcomm MSM 7X00A Multimedia Card Interface driver");
-MODULE_LICENSE("GPL");
diff --git a/drivers/mmc/host/msm_sdcc.h b/drivers/mmc/host/msm_sdcc.h
deleted file mode 100644
index 402028d..0000000
--- a/drivers/mmc/host/msm_sdcc.h
+++ /dev/null
@@ -1,256 +0,0 @@
-/*
- *  linux/drivers/mmc/host/msmsdcc.h - QCT MSM7K SDC Controller
- *
- *  Copyright (C) 2008 Google, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * - Based on mmci.h
- */
-
-#ifndef _MSM_SDCC_H
-#define _MSM_SDCC_H
-
-#define MSMSDCC_CRCI_SDC1	6
-#define MSMSDCC_CRCI_SDC2	7
-#define MSMSDCC_CRCI_SDC3	12
-#define MSMSDCC_CRCI_SDC4	13
-
-#define MMCIPOWER		0x000
-#define MCI_PWR_OFF		0x00
-#define MCI_PWR_UP		0x02
-#define MCI_PWR_ON		0x03
-#define MCI_OD			(1 << 6)
-
-#define MMCICLOCK		0x004
-#define MCI_CLK_ENABLE		(1 << 8)
-#define MCI_CLK_PWRSAVE		(1 << 9)
-#define MCI_CLK_WIDEBUS		(1 << 10)
-#define MCI_CLK_FLOWENA		(1 << 12)
-#define MCI_CLK_INVERTOUT	(1 << 13)
-#define MCI_CLK_SELECTIN	(1 << 14)
-
-#define MMCIARGUMENT		0x008
-#define MMCICOMMAND		0x00c
-#define MCI_CPSM_RESPONSE	(1 << 6)
-#define MCI_CPSM_LONGRSP	(1 << 7)
-#define MCI_CPSM_INTERRUPT	(1 << 8)
-#define MCI_CPSM_PENDING	(1 << 9)
-#define MCI_CPSM_ENABLE		(1 << 10)
-#define MCI_CPSM_PROGENA	(1 << 11)
-#define MCI_CSPM_DATCMD		(1 << 12)
-#define MCI_CSPM_MCIABORT	(1 << 13)
-#define MCI_CSPM_CCSENABLE	(1 << 14)
-#define MCI_CSPM_CCSDISABLE	(1 << 15)
-
-
-#define MMCIRESPCMD		0x010
-#define MMCIRESPONSE0		0x014
-#define MMCIRESPONSE1		0x018
-#define MMCIRESPONSE2		0x01c
-#define MMCIRESPONSE3		0x020
-#define MMCIDATATIMER		0x024
-#define MMCIDATALENGTH		0x028
-
-#define MMCIDATACTRL		0x02c
-#define MCI_DPSM_ENABLE		(1 << 0)
-#define MCI_DPSM_DIRECTION	(1 << 1)
-#define MCI_DPSM_MODE		(1 << 2)
-#define MCI_DPSM_DMAENABLE	(1 << 3)
-
-#define MMCIDATACNT		0x030
-#define MMCISTATUS		0x034
-#define MCI_CMDCRCFAIL		(1 << 0)
-#define MCI_DATACRCFAIL		(1 << 1)
-#define MCI_CMDTIMEOUT		(1 << 2)
-#define MCI_DATATIMEOUT		(1 << 3)
-#define MCI_TXUNDERRUN		(1 << 4)
-#define MCI_RXOVERRUN		(1 << 5)
-#define MCI_CMDRESPEND		(1 << 6)
-#define MCI_CMDSENT		(1 << 7)
-#define MCI_DATAEND		(1 << 8)
-#define MCI_DATABLOCKEND	(1 << 10)
-#define MCI_CMDACTIVE		(1 << 11)
-#define MCI_TXACTIVE		(1 << 12)
-#define MCI_RXACTIVE		(1 << 13)
-#define MCI_TXFIFOHALFEMPTY	(1 << 14)
-#define MCI_RXFIFOHALFFULL	(1 << 15)
-#define MCI_TXFIFOFULL		(1 << 16)
-#define MCI_RXFIFOFULL		(1 << 17)
-#define MCI_TXFIFOEMPTY		(1 << 18)
-#define MCI_RXFIFOEMPTY		(1 << 19)
-#define MCI_TXDATAAVLBL		(1 << 20)
-#define MCI_RXDATAAVLBL		(1 << 21)
-#define MCI_SDIOINTR		(1 << 22)
-#define MCI_PROGDONE		(1 << 23)
-#define MCI_ATACMDCOMPL		(1 << 24)
-#define MCI_SDIOINTOPER		(1 << 25)
-#define MCI_CCSTIMEOUT		(1 << 26)
-
-#define MMCICLEAR		0x038
-#define MCI_CMDCRCFAILCLR	(1 << 0)
-#define MCI_DATACRCFAILCLR	(1 << 1)
-#define MCI_CMDTIMEOUTCLR	(1 << 2)
-#define MCI_DATATIMEOUTCLR	(1 << 3)
-#define MCI_TXUNDERRUNCLR	(1 << 4)
-#define MCI_RXOVERRUNCLR	(1 << 5)
-#define MCI_CMDRESPENDCLR	(1 << 6)
-#define MCI_CMDSENTCLR		(1 << 7)
-#define MCI_DATAENDCLR		(1 << 8)
-#define MCI_DATABLOCKENDCLR	(1 << 10)
-
-#define MMCIMASK0		0x03c
-#define MCI_CMDCRCFAILMASK	(1 << 0)
-#define MCI_DATACRCFAILMASK	(1 << 1)
-#define MCI_CMDTIMEOUTMASK	(1 << 2)
-#define MCI_DATATIMEOUTMASK	(1 << 3)
-#define MCI_TXUNDERRUNMASK	(1 << 4)
-#define MCI_RXOVERRUNMASK	(1 << 5)
-#define MCI_CMDRESPENDMASK	(1 << 6)
-#define MCI_CMDSENTMASK		(1 << 7)
-#define MCI_DATAENDMASK		(1 << 8)
-#define MCI_DATABLOCKENDMASK	(1 << 10)
-#define MCI_CMDACTIVEMASK	(1 << 11)
-#define MCI_TXACTIVEMASK	(1 << 12)
-#define MCI_RXACTIVEMASK	(1 << 13)
-#define MCI_TXFIFOHALFEMPTYMASK	(1 << 14)
-#define MCI_RXFIFOHALFFULLMASK	(1 << 15)
-#define MCI_TXFIFOFULLMASK	(1 << 16)
-#define MCI_RXFIFOFULLMASK	(1 << 17)
-#define MCI_TXFIFOEMPTYMASK	(1 << 18)
-#define MCI_RXFIFOEMPTYMASK	(1 << 19)
-#define MCI_TXDATAAVLBLMASK	(1 << 20)
-#define MCI_RXDATAAVLBLMASK	(1 << 21)
-#define MCI_SDIOINTMASK		(1 << 22)
-#define MCI_PROGDONEMASK	(1 << 23)
-#define MCI_ATACMDCOMPLMASK	(1 << 24)
-#define MCI_SDIOINTOPERMASK	(1 << 25)
-#define MCI_CCSTIMEOUTMASK	(1 << 26)
-
-#define MMCIMASK1		0x040
-#define MMCIFIFOCNT		0x044
-#define MCICCSTIMER		0x058
-
-#define MMCIFIFO		0x080 /* to 0x0bc */
-
-#define MCI_IRQENABLE	\
-	(MCI_CMDCRCFAILMASK|MCI_DATACRCFAILMASK|MCI_CMDTIMEOUTMASK|	\
-	MCI_DATATIMEOUTMASK|MCI_TXUNDERRUNMASK|MCI_RXOVERRUNMASK|	\
-	MCI_CMDRESPENDMASK|MCI_CMDSENTMASK|MCI_DATAENDMASK|MCI_PROGDONEMASK)
-
-#define MCI_IRQ_PIO \
-	(MCI_RXDATAAVLBLMASK | MCI_TXDATAAVLBLMASK | MCI_RXFIFOEMPTYMASK | \
-	 MCI_TXFIFOEMPTYMASK | MCI_RXFIFOFULLMASK | MCI_TXFIFOFULLMASK | \
-	 MCI_RXFIFOHALFFULLMASK | MCI_TXFIFOHALFEMPTYMASK | \
-	 MCI_RXACTIVEMASK | MCI_TXACTIVEMASK)
-/*
- * The size of the FIFO in bytes.
- */
-#define MCI_FIFOSIZE	(16*4)
-
-#define MCI_FIFOHALFSIZE (MCI_FIFOSIZE / 2)
-
-#define NR_SG		32
-
-struct clk;
-
-struct msmsdcc_nc_dmadata {
-	dmov_box	cmd[NR_SG];
-	uint32_t	cmdptr;
-};
-
-struct msmsdcc_dma_data {
-	struct msmsdcc_nc_dmadata	*nc;
-	dma_addr_t			nc_busaddr;
-	dma_addr_t			cmd_busaddr;
-	dma_addr_t			cmdptr_busaddr;
-
-	struct msm_dmov_cmd		hdr;
-	enum dma_data_direction		dir;
-
-	struct scatterlist		*sg;
-	int				num_ents;
-
-	int				channel;
-	struct msmsdcc_host		*host;
-	int				busy; /* Set if DM is busy */
-	int				active;
-	unsigned int			result;
-	struct msm_dmov_errdata		err;
-};
-
-struct msmsdcc_pio_data {
-	struct scatterlist	*sg;
-	unsigned int		sg_len;
-	unsigned int		sg_off;
-};
-
-struct msmsdcc_curr_req {
-	struct mmc_request	*mrq;
-	struct mmc_command	*cmd;
-	struct mmc_data		*data;
-	unsigned int		xfer_size;	/* Total data size */
-	unsigned int		xfer_remain;	/* Bytes remaining to send */
-	unsigned int		data_xfered;	/* Bytes acked by BLKEND irq */
-	int			got_dataend;
-	int			user_pages;
-};
-
-struct msmsdcc_stats {
-	unsigned int reqs;
-	unsigned int cmds;
-	unsigned int cmdpoll_hits;
-	unsigned int cmdpoll_misses;
-};
-
-struct msmsdcc_host {
-	struct resource		*cmd_irqres;
-	struct resource		*memres;
-	struct resource		*dmares;
-	void __iomem		*base;
-	int			pdev_id;
-	unsigned int		stat_irq;
-
-	struct msmsdcc_curr_req	curr;
-
-	struct mmc_host		*mmc;
-	struct clk		*clk;		/* main MMC bus clock */
-	struct clk		*pclk;		/* SDCC peripheral bus clock */
-	unsigned int		clks_on;	/* set if clocks are enabled */
-	struct timer_list	busclk_timer;
-
-	unsigned int		eject;		/* eject state */
-
-	spinlock_t		lock;
-
-	unsigned int		clk_rate;	/* Current clock rate */
-	unsigned int		pclk_rate;
-
-	u32			pwr;
-	u32			saved_irq0mask;	/* MMCIMASK0 reg value */
-	struct msm_mmc_platform_data *plat;
-
-	struct timer_list	timer;
-	unsigned int		oldstat;
-
-	struct msmsdcc_dma_data	dma;
-	struct msmsdcc_pio_data	pio;
-	int			cmdpoll;
-	struct msmsdcc_stats	stats;
-
-	struct tasklet_struct	dma_tlet;
-	/* Command parameters */
-	unsigned int		cmd_timeout;
-	unsigned int		cmd_pio_irqmask;
-	unsigned int		cmd_datactrl;
-	struct mmc_command	*cmd_cmd;
-	u32			cmd_c;
-	bool			gpio_config_status;
-
-	bool prog_scan;
-	bool prog_enable;
-};
-
-#endif
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index 45f67c6..a65f821 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -275,6 +275,7 @@
 
 config AT91_CF
 	tristate "AT91 CompactFlash Controller"
+	depends on PCI
 	depends on PCMCIA && ARCH_AT91
 	depends on !ARCH_MULTIPLATFORM
 	help
diff --git a/drivers/pcmcia/at91_cf.c b/drivers/pcmcia/at91_cf.c
index bfb799c..e7775a4 100644
--- a/drivers/pcmcia/at91_cf.c
+++ b/drivers/pcmcia/at91_cf.c
@@ -317,13 +317,14 @@
 	} else
 		cf->socket.pci_irq = nr_irqs + 1;
 
-	/* pcmcia layer only remaps "real" memory not iospace */
-	cf->socket.io_offset = (unsigned long) devm_ioremap(&pdev->dev,
-					cf->phys_baseaddr + CF_IO_PHYS, SZ_2K);
-	if (!cf->socket.io_offset) {
-		status = -ENXIO;
+	/*
+	 * pcmcia layer only remaps "real" memory not iospace
+	 * io_offset is set to 0x10000 to avoid the check in static_find_io().
+	 * */
+	cf->socket.io_offset = 0x10000;
+	status = pci_ioremap_io(0x10000, cf->phys_baseaddr + CF_IO_PHYS);
+	if (status)
 		goto fail0a;
-	}
 
 	/* reserve chip-select regions */
 	if (!devm_request_mem_region(&pdev->dev, io->start, resource_size(io), "at91_cf")) {
diff --git a/include/linux/platform_data/mmc-msm_sdcc.h b/include/linux/platform_data/mmc-msm_sdcc.h
deleted file mode 100644
index 55aa873..0000000
--- a/include/linux/platform_data/mmc-msm_sdcc.h
+++ /dev/null
@@ -1,27 +0,0 @@
-#ifndef __MMC_MSM_SDCC_H
-#define __MMC_MSM_SDCC_H
-
-#include <linux/mmc/host.h>
-#include <linux/mmc/card.h>
-#include <linux/mmc/sdio_func.h>
-
-struct msm_mmc_gpio {
-	unsigned no;
-	const char *name;
-};
-
-struct msm_mmc_gpio_data {
-	struct msm_mmc_gpio *gpio;
-	u8 size;
-};
-
-struct msm_mmc_platform_data {
-	unsigned int ocr_mask;			/* available voltages */
-	u32 (*translate_vdd)(struct device *, unsigned int);
-	unsigned int (*status)(struct device *);
-	int (*register_status_notify)(void (*callback)(int card_present, void *dev_id), void *dev_id);
-	struct msm_mmc_gpio_data *gpio_data;
-	void (*init_card)(struct mmc_card *card);
-};
-
-#endif