# SPDX-License-Identifier: GPL-2.0
if ETRAX_ARCH_V32

config ETRAX_ETHERNET
	bool "Ethernet support"
	depends on ETRAX_ARCH_V32 && NETDEVICES
	select MII
	help
	  This option enables the ETRAX FS built-in 10/100Mbit Ethernet
	  controller.

config ETRAX_NO_PHY
	bool "PHY not present"
	depends on ETRAX_ETHERNET
	help
	  This option disables all MDIO communication with an ethernet
	  transceiver connected to the MII interface. This option shall
	  typically be enabled if the MII interface is connected to a
	  switch. This option should normally be disabled. If enabled,
	  speed and duplex will be locked to 100 Mbit and full duplex.

config ETRAXFS_SERIAL
	bool "Serial-port support"
	depends on ETRAX_ARCH_V32
	select SERIAL_CORE
	select SERIAL_CORE_CONSOLE
	help
	  Enables the ETRAX FS serial driver for ser0 (ttyS0)
	  You probably want this enabled.

config ETRAX_RS485
	bool "RS-485 support"
	depends on ETRAXFS_SERIAL
	help
	  Enables support for RS-485 serial communication.

config ETRAX_RS485_DISABLE_RECEIVER
	bool "Disable serial receiver"
	depends on ETRAX_RS485
	help
	  It is necessary to disable the serial receiver to avoid serial
	  loopback.  Not all products are able to do this in software only.

config ETRAX_SERIAL_PORT0
	bool "Serial port 0 enabled"
	depends on ETRAXFS_SERIAL
	help
	  Enables the ETRAX FS serial driver for ser0 (ttyS0)
	  Normally you want this on. You can control what DMA channels to use
	  if you do not need DMA to something else.
	  ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.

config ETRAX_SERIAL_PORT1
	bool "Serial port 1 enabled"
	depends on ETRAXFS_SERIAL
	help
	  Enables the ETRAX FS serial driver for ser1 (ttyS1).

config ETRAX_SERIAL_PORT2
	bool "Serial port 2 enabled"
	depends on ETRAXFS_SERIAL
	help
	  Enables the ETRAX FS serial driver for ser2 (ttyS2).

config ETRAX_SERIAL_PORT3
	bool "Serial port 3 enabled"
	depends on ETRAXFS_SERIAL
	help
	  Enables the ETRAX FS serial driver for ser3 (ttyS3).

config ETRAX_SYNCHRONOUS_SERIAL
	bool "Synchronous serial-port support"
	depends on ETRAX_ARCH_V32
	help
	  Enables the ETRAX FS synchronous serial driver.

config ETRAX_SYNCHRONOUS_SERIAL_PORT0
         bool "Synchronous serial port 0 enabled"
         depends on ETRAX_SYNCHRONOUS_SERIAL
         help
           Enabled synchronous serial port 0.

config ETRAX_SYNCHRONOUS_SERIAL0_DMA
         bool "Enable DMA on synchronous serial port 0."
         depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
         help
           A synchronous serial port can run in manual or DMA mode.
           Selecting this option will make it run in DMA mode.

config ETRAX_SYNCHRONOUS_SERIAL_PORT1
         bool "Synchronous serial port 1 enabled"
         depends on ETRAX_SYNCHRONOUS_SERIAL && ETRAXFS
         help
           Enabled synchronous serial port 1.

config ETRAX_SYNCHRONOUS_SERIAL1_DMA
         bool "Enable DMA on synchronous serial port 1."
         depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
         help
           A synchronous serial port can run in manual or DMA mode.
           Selecting this option will make it run in DMA mode.

config ETRAX_AXISFLASHMAP
	bool "Axis flash-map support"
	depends on ETRAX_ARCH_V32
	select MTD
	select MTD_CFI
	select MTD_CFI_AMDSTD
	select MTD_JEDECPROBE
	select MTD_BLOCK
	select MTD_COMPLEX_MAPPINGS
	select MTD_MTDRAM
	help
	  This option enables MTD mapping of flash devices.  Needed to use
	  flash memories.  If unsure, say Y.

config ETRAX_AXISFLASHMAP_MTD0WHOLE
	bool "MTD0 is whole boot flash device"
	depends on ETRAX_AXISFLASHMAP
	help
	  When this option is not set, mtd0 refers to the first partition
	  on the boot flash device. When set, mtd0 refers to the whole
	  device, with mtd1 referring to the first partition etc.

config ETRAX_PTABLE_SECTOR
	int "Byte-offset of partition table sector"
	depends on ETRAX_AXISFLASHMAP
	default "65536"
	help
	  Byte-offset of the partition table in the first flash chip.
	  The default value is 64kB and should not be changed unless
	  you know exactly what you are doing. The only valid reason
	  for changing this is when the flash block size is bigger
	  than 64kB (e.g. when using two parallel 16 bit flashes).

config ETRAX_NANDFLASH
	bool "NAND flash support"
	depends on ETRAX_ARCH_V32
	select MTD_NAND
	help
	  This option enables MTD mapping of NAND flash devices.  Needed to use
	  NAND flash memories.  If unsure, say Y.

config ETRAX_NANDBOOT
	bool "Boot from NAND flash"
	depends on ETRAX_NANDFLASH
	help
	  This options enables booting from NAND flash devices.
	  Say Y if your boot code, kernel and root file system is in
	  NAND flash. Say N if they are in NOR flash.

config ETRAX_CARDBUS
        bool "Cardbus support"
        depends on ETRAX_ARCH_V32
        help
	 Enabled the ETRAX Cardbus driver.

config PCI
       bool
       depends on ETRAX_CARDBUS
       default y
       select HAVE_GENERIC_DMA_COHERENT

config ETRAX_IOP_FW_LOAD
	tristate "IO-processor hotplug firmware loading support"
	depends on ETRAX_ARCH_V32
	select FW_LOADER
	help
	  Enables IO-processor hotplug firmware loading support.

config ETRAX_STREAMCOPROC
	tristate "Stream co-processor driver enabled"
	depends on ETRAX_ARCH_V32
	help
	  This option enables a driver for the stream co-processor
	  for cryptographic operations.

config ETRAX_MMC_IOP
	tristate "MMC/SD host driver using IO-processor"
	depends on ETRAX_ARCH_V32 && MMC
	help
	  This option enables the SD/MMC host controller interface.
	  The host controller is implemented using the built in
	  IO-Processor. Only the SPU is used in this implementation.

config ETRAX_SPI_MMC
# Make this one of several "choices" (possible simultaneously but
# suggested uniquely) when an IOP driver emerges for "real" MMC/SD
# protocol support.
	tristate
	depends on !ETRAX_MMC_IOP
	default MMC
	select SPI
	select MMC_SPI

# While the board info is MMC_SPI only, the drivers are written to be
# independent of MMC_SPI, so we'll keep SPI non-dependent on the
# MMC_SPI config choices (well, except for a single depends-on-line
# for the board-info file until a separate non-MMC SPI board file
# emerges).
# FIXME: When that happens, we'll need to be able to ask for and
# configure non-MMC SPI ports together with MMC_SPI ports (if multiple
# SPI ports are enabled).

config SPI_ETRAX_SSER
	tristate
	depends on SPI_MASTER && ETRAX_ARCH_V32
	select SPI_BITBANG
	help
	  This enables using an synchronous serial (sser) port as a
	  SPI master controller on Axis ETRAX FS and later.  The
	  driver can be configured to use any sser port.

config SPI_ETRAX_GPIO
	tristate
	depends on SPI_MASTER && ETRAX_ARCH_V32
	select SPI_BITBANG
	help
	  This enables using GPIO pins port as a SPI master controller
	  on Axis ETRAX FS and later.  The driver can be configured to
	  use any GPIO pins.

config ETRAX_SPI_SSER0
	tristate "SPI using synchronous serial port 0 (sser0)"
	depends on ETRAX_SPI_MMC
	default m if MMC_SPI=m
	default y if MMC_SPI=y
	default y if MMC_SPI=n
	select SPI_ETRAX_SSER
	help
	  Say Y for an MMC/SD socket connected to synchronous serial port 0,
	  or for devices using the SPI protocol on that port.  Say m if you
	  want to build it as a module, which will be named spi_crisv32_sser.
	  (You need to select MMC separately.)

config ETRAX_SPI_SSER1
	tristate "SPI using synchronous serial port 1 (sser1)"
	depends on ETRAX_SPI_MMC
	default m if MMC_SPI=m && ETRAX_SPI_SSER0=n
	default y if MMC_SPI=y && ETRAX_SPI_SSER0=n
	default y if MMC_SPI=n && ETRAX_SPI_SSER0=n
	select SPI_ETRAX_SSER
	help
	  Say Y for an MMC/SD socket connected to synchronous serial port 1,
	  or for devices using the SPI protocol on that port.  Say m if you
	  want to build it as a module, which will be named spi_crisv32_sser.
	  (You need to select MMC separately.)

config ETRAX_SPI_GPIO
	tristate "Bitbanged SPI using gpio pins"
	depends on ETRAX_SPI_MMC
	select SPI_ETRAX_GPIO
	default m if MMC_SPI=m && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
	default y if MMC_SPI=y && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
	default y if MMC_SPI=n && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
	help
	  Say Y for an MMC/SD socket connected to general I/O pins (but not
	  a complete synchronous serial ports), or for devices using the SPI
	  protocol on general I/O pins.  Slow and slows down the system.
	  Say m to build it as a module, which will be called spi_crisv32_gpio.
	  (You need to select MMC separately.)

endif