Merge branch 'imx' into dmaengine-fixes
diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index 297f48b..07bca49 100644
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -79,6 +79,7 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include <linux/delay.h>
#include <linux/dmapool.h>
#include <linux/dmaengine.h>
#include <linux/amba/bus.h>
@@ -235,16 +236,19 @@
}
/*
- * Overall DMAC remains enabled always.
+ * Pause the channel by setting the HALT bit.
*
- * Disabling individual channels could lose data.
+ * For M->P transfers, pause the DMAC first and then stop the peripheral -
+ * the FIFO can only drain if the peripheral is still requesting data.
+ * (note: this can still timeout if the DMAC FIFO never drains of data.)
*
- * Disable the peripheral DMA after disabling the DMAC in order to allow
- * the DMAC FIFO to drain, and hence allow the channel to show inactive
+ * For P->M transfers, disable the peripheral first to stop it filling
+ * the DMAC FIFO, and then pause the DMAC.
*/
static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
{
u32 val;
+ int timeout;
/* Set the HALT bit and wait for the FIFO to drain */
val = readl(ch->base + PL080_CH_CONFIG);
@@ -252,8 +256,13 @@
writel(val, ch->base + PL080_CH_CONFIG);
/* Wait for channel inactive */
- while (pl08x_phy_channel_busy(ch))
- cpu_relax();
+ for (timeout = 1000; timeout; timeout--) {
+ if (!pl08x_phy_channel_busy(ch))
+ break;
+ udelay(1);
+ }
+ if (pl08x_phy_channel_busy(ch))
+ pr_err("pl08x: channel%u timeout waiting for pause\n", ch->id);
}
static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
@@ -267,19 +276,24 @@
}
-/* Stops the channel */
-static void pl08x_stop_phy_chan(struct pl08x_phy_chan *ch)
+/*
+ * pl08x_terminate_phy_chan() stops the channel, clears the FIFO and
+ * clears any pending interrupt status. This should not be used for
+ * an on-going transfer, but as a method of shutting down a channel
+ * (eg, when it's no longer used) or terminating a transfer.
+ */
+static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
{
- u32 val;
+ u32 val = readl(ch->base + PL080_CH_CONFIG);
- pl08x_pause_phy_chan(ch);
+ val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK);
- /* Disable channel */
- val = readl(ch->base + PL080_CH_CONFIG);
- val &= ~PL080_CONFIG_ENABLE;
- val &= ~PL080_CONFIG_ERR_IRQ_MASK;
- val &= ~PL080_CONFIG_TC_IRQ_MASK;
writel(val, ch->base + PL080_CH_CONFIG);
+
+ writel(1 << ch->id, pl08x->base + PL080_ERR_CLEAR);
+ writel(1 << ch->id, pl08x->base + PL080_TC_CLEAR);
}
static inline u32 get_bytes_in_cctl(u32 cctl)
@@ -404,13 +418,12 @@
{
unsigned long flags;
+ spin_lock_irqsave(&ch->lock, flags);
+
/* Stop the channel and clear its interrupts */
- pl08x_stop_phy_chan(ch);
- writel((1 << ch->id), pl08x->base + PL080_ERR_CLEAR);
- writel((1 << ch->id), pl08x->base + PL080_TC_CLEAR);
+ pl08x_terminate_phy_chan(pl08x, ch);
/* Mark it as free */
- spin_lock_irqsave(&ch->lock, flags);
ch->serving = NULL;
spin_unlock_irqrestore(&ch->lock, flags);
}
@@ -1449,7 +1462,7 @@
plchan->state = PL08X_CHAN_IDLE;
if (plchan->phychan) {
- pl08x_stop_phy_chan(plchan->phychan);
+ pl08x_terminate_phy_chan(pl08x, plchan->phychan);
/*
* Mark physical channel as free and free any slave
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
index 0123740..b6d1455 100644
--- a/drivers/dma/imx-sdma.c
+++ b/drivers/dma/imx-sdma.c
@@ -771,15 +771,15 @@
__raw_writel(1 << channel, sdma->regs + SDMA_H_START);
}
-static dma_cookie_t sdma_assign_cookie(struct sdma_channel *sdma)
+static dma_cookie_t sdma_assign_cookie(struct sdma_channel *sdmac)
{
- dma_cookie_t cookie = sdma->chan.cookie;
+ dma_cookie_t cookie = sdmac->chan.cookie;
if (++cookie < 0)
cookie = 1;
- sdma->chan.cookie = cookie;
- sdma->desc.cookie = cookie;
+ sdmac->chan.cookie = cookie;
+ sdmac->desc.cookie = cookie;
return cookie;
}
@@ -1142,7 +1142,7 @@
/* download the RAM image for SDMA */
sdma_load_script(sdma, ram_code,
header->ram_code_size,
- sdma->script_addrs->ram_code_start_addr);
+ addr->ram_code_start_addr);
clk_disable(sdma->clk);
sdma_add_scripts(sdma, addr);
@@ -1354,7 +1354,7 @@
err_request_region:
err_irq:
kfree(sdma);
- return 0;
+ return ret;
}
static int __exit sdma_remove(struct platform_device *pdev)
diff --git a/drivers/dma/ipu/ipu_idmac.c b/drivers/dma/ipu/ipu_idmac.c
index cb26ee9..c1a125e7 100644
--- a/drivers/dma/ipu/ipu_idmac.c
+++ b/drivers/dma/ipu/ipu_idmac.c
@@ -1145,29 +1145,6 @@
reg = idmac_read_icreg(ipu, IDMAC_CHA_EN);
idmac_write_icreg(ipu, reg & ~chan_mask, IDMAC_CHA_EN);
- /*
- * Problem (observed with channel DMAIC_7): after enabling the channel
- * and initialising buffers, there comes an interrupt with current still
- * pointing at buffer 0, whereas it should use buffer 0 first and only
- * generate an interrupt when it is done, then current should already
- * point to buffer 1. This spurious interrupt also comes on channel
- * DMASDC_0. With DMAIC_7 normally, is we just leave the ISR after the
- * first interrupt, there comes the second with current correctly
- * pointing to buffer 1 this time. But sometimes this second interrupt
- * doesn't come and the channel hangs. Clearing BUFx_RDY when disabling
- * the channel seems to prevent the channel from hanging, but it doesn't
- * prevent the spurious interrupt. This might also be unsafe. Think
- * about the IDMAC controller trying to switch to a buffer, when we
- * clear the ready bit, and re-enable it a moment later.
- */
- reg = idmac_read_ipureg(ipu, IPU_CHA_BUF0_RDY);
- idmac_write_ipureg(ipu, 0, IPU_CHA_BUF0_RDY);
- idmac_write_ipureg(ipu, reg & ~(1UL << channel), IPU_CHA_BUF0_RDY);
-
- reg = idmac_read_ipureg(ipu, IPU_CHA_BUF1_RDY);
- idmac_write_ipureg(ipu, 0, IPU_CHA_BUF1_RDY);
- idmac_write_ipureg(ipu, reg & ~(1UL << channel), IPU_CHA_BUF1_RDY);
-
spin_unlock_irqrestore(&ipu->lock, flags);
return 0;
@@ -1246,33 +1223,6 @@
/* Other interrupts do not interfere with this channel */
spin_lock(&ichan->lock);
- if (unlikely(chan_id != IDMAC_SDC_0 && chan_id != IDMAC_SDC_1 &&
- ((curbuf >> chan_id) & 1) == ichan->active_buffer &&
- !list_is_last(ichan->queue.next, &ichan->queue))) {
- int i = 100;
-
- /* This doesn't help. See comment in ipu_disable_channel() */
- while (--i) {
- curbuf = idmac_read_ipureg(&ipu_data, IPU_CHA_CUR_BUF);
- if (((curbuf >> chan_id) & 1) != ichan->active_buffer)
- break;
- cpu_relax();
- }
-
- if (!i) {
- spin_unlock(&ichan->lock);
- dev_dbg(dev,
- "IRQ on active buffer on channel %x, active "
- "%d, ready %x, %x, current %x!\n", chan_id,
- ichan->active_buffer, ready0, ready1, curbuf);
- return IRQ_NONE;
- } else
- dev_dbg(dev,
- "Buffer deactivated on channel %x, active "
- "%d, ready %x, %x, current %x, rest %d!\n", chan_id,
- ichan->active_buffer, ready0, ready1, curbuf, i);
- }
-
if (unlikely((ichan->active_buffer && (ready1 >> chan_id) & 1) ||
(!ichan->active_buffer && (ready0 >> chan_id) & 1)
)) {
