Merge JFFS2 updates from David Woodhouse
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index 1fe6dde..7d4c8eb 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -1,7 +1,7 @@
Atmel NAND flash
Required properties:
-- compatible : "atmel,at91rm9200-nand".
+- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand".
- reg : should specify localbus address and size used for the chip,
and hardware ECC controller if available.
If the hardware ECC is PMECC, it should contain address and size for
diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
index 823d134..4461dc7 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -1,7 +1,7 @@
* Freescale Quad Serial Peripheral Interface(QuadSPI)
Required properties:
- - compatible : Should be "fsl,vf610-qspi"
+ - compatible : Should be "fsl,vf610-qspi" or "fsl,imx6sx-qspi"
- reg : the first contains the register location and length,
the second contains the memory mapping address and length
- reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
index a011fdf..d02acaf 100644
--- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -1,7 +1,7 @@
* Freescale General-Purpose Media Interface (GPMI)
The GPMI nand controller provides an interface to control the
-NAND flash chips. We support only one NAND chip now.
+NAND flash chips.
Required properties:
- compatible : should be "fsl,<chip>-gpmi-nand"
diff --git a/Documentation/devicetree/bindings/mtd/hisi504-nand.txt b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
new file mode 100644
index 0000000..2e35f06
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/hisi504-nand.txt
@@ -0,0 +1,47 @@
+Hisilicon Hip04 Soc NAND controller DT binding
+
+Required properties:
+
+- compatible: Should be "hisilicon,504-nfc".
+- reg: The first contains base physical address and size of
+ NAND controller's registers. The second contains base
+ physical address and size of NAND controller's buffer.
+- interrupts: Interrupt number for nfc.
+- nand-bus-width: See nand.txt.
+- nand-ecc-mode: Support none and hw ecc mode.
+- #address-cells: Partition address, should be set 1.
+- #size-cells: Partition size, should be set 1.
+
+Optional properties:
+
+- nand-ecc-strength: Number of bits to correct per ECC step.
+- nand-ecc-step-size: Number of data bytes covered by a single ECC step.
+
+The following ECC strength and step size are currently supported:
+
+ - nand-ecc-strength = <16>, nand-ecc-step-size = <1024>
+
+Flash chip may optionally contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail.
+
+Example:
+
+ nand: nand@4020000 {
+ compatible = "hisilicon,504-nfc";
+ reg = <0x4020000 0x10000>, <0x5000000 0x1000>;
+ interrupts = <0 379 4>;
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ nand-ecc-strength = <16>;
+ nand-ecc-step-size = <1024>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "nand_text";
+ reg = <0x00000000 0x00400000>;
+ };
+
+ ...
+
+ };
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
index 6b9f680..4a0a48b 100644
--- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -36,6 +36,11 @@
- vendor-id : Contains the flash chip's vendor id (1 byte).
- device-id : Contains the flash chip's device id (1 byte).
+For ROM compatible devices (and ROM fallback from cfi-flash), the following
+additional (optional) property is defined:
+
+ - erase-size : The chip's physical erase block size in bytes.
+
The device tree may optionally contain sub-nodes describing partitions of the
address space. See partition.txt for more detail.
diff --git a/MAINTAINERS b/MAINTAINERS
index ddb9ac8..cabe127 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4028,6 +4028,12 @@
F: include/linux/platform_data/video-imxfb.h
F: drivers/video/fbdev/imxfb.c
+FREESCALE QUAD SPI DRIVER
+M: Han Xu <han.xu@freescale.com>
+L: linux-mtd@lists.infradead.org
+S: Maintained
+F: drivers/mtd/spi-nor/fsl-quadspi.c
+
FREESCALE SOC FS_ENET DRIVER
M: Pantelis Antoniou <pantelis.antoniou@gmail.com>
M: Vitaly Bordug <vbordug@ru.mvista.com>
diff --git a/arch/mips/include/asm/mach-jz4740/jz4740_nand.h b/arch/mips/include/asm/mach-jz4740/jz4740_nand.h
index 986982d..79cff26 100644
--- a/arch/mips/include/asm/mach-jz4740/jz4740_nand.h
+++ b/arch/mips/include/asm/mach-jz4740/jz4740_nand.h
@@ -27,8 +27,6 @@
struct nand_ecclayout *ecc_layout;
- unsigned int busy_gpio;
-
unsigned char banks[JZ_NAND_NUM_BANKS];
void (*ident_callback)(struct platform_device *, struct nand_chip *,
diff --git a/arch/mips/jz4740/board-qi_lb60.c b/arch/mips/jz4740/board-qi_lb60.c
index c454525..9dd051e 100644
--- a/arch/mips/jz4740/board-qi_lb60.c
+++ b/arch/mips/jz4740/board-qi_lb60.c
@@ -140,10 +140,18 @@
static struct jz_nand_platform_data qi_lb60_nand_pdata = {
.ident_callback = qi_lb60_nand_ident,
- .busy_gpio = 94,
.banks = { 1 },
};
+static struct gpiod_lookup_table qi_lb60_nand_gpio_table = {
+ .dev_id = "jz4740-nand.0",
+ .table = {
+ GPIO_LOOKUP("Bank C", 30, "busy", 0),
+ { },
+ },
+};
+
+
/* Keyboard*/
#define KEY_QI_QI KEY_F13
@@ -472,6 +480,7 @@
jz4740_mmc_device.dev.platform_data = &qi_lb60_mmc_pdata;
gpiod_add_lookup_table(&qi_lb60_audio_gpio_table);
+ gpiod_add_lookup_table(&qi_lb60_nand_gpio_table);
jz4740_serial_device_register();
diff --git a/drivers/mtd/bcm47xxpart.c b/drivers/mtd/bcm47xxpart.c
index cc13ea5..c0720c1 100644
--- a/drivers/mtd/bcm47xxpart.c
+++ b/drivers/mtd/bcm47xxpart.c
@@ -15,6 +15,8 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <uapi/linux/magic.h>
+
/*
* NAND flash on Netgear R6250 was verified to contain 15 partitions.
* This will result in allocating too big array for some old devices, but the
@@ -39,7 +41,8 @@
#define ML_MAGIC1 0x39685a42
#define ML_MAGIC2 0x26594131
#define TRX_MAGIC 0x30524448
-#define SQSH_MAGIC 0x71736873 /* shsq */
+#define SHSQ_MAGIC 0x71736873 /* shsq (weird ZTE H218N endianness) */
+#define UBI_EC_MAGIC 0x23494255 /* UBI# */
struct trx_header {
uint32_t magic;
@@ -50,7 +53,7 @@
uint32_t offset[3];
} __packed;
-static void bcm47xxpart_add_part(struct mtd_partition *part, char *name,
+static void bcm47xxpart_add_part(struct mtd_partition *part, const char *name,
u64 offset, uint32_t mask_flags)
{
part->name = name;
@@ -58,6 +61,26 @@
part->mask_flags = mask_flags;
}
+static const char *bcm47xxpart_trx_data_part_name(struct mtd_info *master,
+ size_t offset)
+{
+ uint32_t buf;
+ size_t bytes_read;
+
+ if (mtd_read(master, offset, sizeof(buf), &bytes_read,
+ (uint8_t *)&buf) < 0) {
+ pr_err("mtd_read error while parsing (offset: 0x%X)!\n",
+ offset);
+ goto out_default;
+ }
+
+ if (buf == UBI_EC_MAGIC)
+ return "ubi";
+
+out_default:
+ return "rootfs";
+}
+
static int bcm47xxpart_parse(struct mtd_info *master,
struct mtd_partition **pparts,
struct mtd_part_parser_data *data)
@@ -73,8 +96,12 @@
int last_trx_part = -1;
int possible_nvram_sizes[] = { 0x8000, 0xF000, 0x10000, };
- if (blocksize <= 0x10000)
- blocksize = 0x10000;
+ /*
+ * Some really old flashes (like AT45DB*) had smaller erasesize-s, but
+ * partitions were aligned to at least 0x1000 anyway.
+ */
+ if (blocksize < 0x1000)
+ blocksize = 0x1000;
/* Alloc */
parts = kzalloc(sizeof(struct mtd_partition) * BCM47XXPART_MAX_PARTS,
@@ -186,8 +213,11 @@
* we want to have jffs2 (overlay) in the same mtd.
*/
if (trx->offset[i]) {
+ const char *name;
+
+ name = bcm47xxpart_trx_data_part_name(master, offset + trx->offset[i]);
bcm47xxpart_add_part(&parts[curr_part++],
- "rootfs",
+ name,
offset + trx->offset[i],
0);
i++;
@@ -205,7 +235,8 @@
}
/* Squashfs on devices not using TRX */
- if (buf[0x000 / 4] == SQSH_MAGIC) {
+ if (le32_to_cpu(buf[0x000 / 4]) == SQUASHFS_MAGIC ||
+ buf[0x000 / 4] == SHSQ_MAGIC) {
bcm47xxpart_add_part(&parts[curr_part++], "rootfs",
offset, 0);
continue;
diff --git a/drivers/mtd/chips/map_ram.c b/drivers/mtd/chips/map_ram.c
index 991c2a1..afb43d5 100644
--- a/drivers/mtd/chips/map_ram.c
+++ b/drivers/mtd/chips/map_ram.c
@@ -68,6 +68,7 @@
mtd->_get_unmapped_area = mapram_unmapped_area;
mtd->_read = mapram_read;
mtd->_write = mapram_write;
+ mtd->_panic_write = mapram_write;
mtd->_sync = mapram_nop;
mtd->flags = MTD_CAP_RAM;
mtd->writesize = 1;
diff --git a/drivers/mtd/chips/map_rom.c b/drivers/mtd/chips/map_rom.c
index 47a43cf..e67f73a 100644
--- a/drivers/mtd/chips/map_rom.c
+++ b/drivers/mtd/chips/map_rom.c
@@ -11,6 +11,7 @@
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/init.h>
+#include <linux/of.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
@@ -28,6 +29,15 @@
.module = THIS_MODULE
};
+static unsigned int default_erasesize(struct map_info *map)
+{
+ const __be32 *erase_size = NULL;
+
+ erase_size = of_get_property(map->device_node, "erase-size", NULL);
+
+ return !erase_size ? map->size : be32_to_cpu(*erase_size);
+}
+
static struct mtd_info *map_rom_probe(struct map_info *map)
{
struct mtd_info *mtd;
@@ -47,8 +57,9 @@
mtd->_sync = maprom_nop;
mtd->_erase = maprom_erase;
mtd->flags = MTD_CAP_ROM;
- mtd->erasesize = map->size;
+ mtd->erasesize = default_erasesize(map);
mtd->writesize = 1;
+ mtd->writebufsize = 1;
__module_get(THIS_MODULE);
return mtd;
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 54ffe52..3060025 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -24,6 +24,7 @@
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/of.h>
+#include <linux/clk.h>
#include "serial_flash_cmds.h"
@@ -262,6 +263,7 @@
struct mtd_info mtd;
struct mutex lock;
struct flash_info *info;
+ struct clk *clk;
uint32_t configuration;
uint32_t fifo_dir_delay;
@@ -663,6 +665,23 @@
SEQ_CFG_STARTSEQ),
};
+/* Dummy sequence to read one byte of data from flash into the FIFO */
+static const struct stfsm_seq stfsm_seq_load_fifo_byte = {
+ .data_size = TRANSFER_SIZE(1),
+ .seq_opc[0] = (SEQ_OPC_PADS_1 |
+ SEQ_OPC_CYCLES(8) |
+ SEQ_OPC_OPCODE(SPINOR_OP_RDID)),
+ .seq = {
+ STFSM_INST_CMD1,
+ STFSM_INST_DATA_READ,
+ STFSM_INST_STOP,
+ },
+ .seq_cfg = (SEQ_CFG_PADS_1 |
+ SEQ_CFG_READNOTWRITE |
+ SEQ_CFG_CSDEASSERT |
+ SEQ_CFG_STARTSEQ),
+};
+
static int stfsm_n25q_en_32bit_addr_seq(struct stfsm_seq *seq)
{
seq->seq_opc[0] = (SEQ_OPC_PADS_1 | SEQ_OPC_CYCLES(8) |
@@ -695,22 +714,6 @@
return (readl(fsm->base + SPI_FAST_SEQ_STA) >> 5) & 0x7f;
}
-static void stfsm_clear_fifo(struct stfsm *fsm)
-{
- uint32_t avail;
-
- for (;;) {
- avail = stfsm_fifo_available(fsm);
- if (!avail)
- break;
-
- while (avail) {
- readl(fsm->base + SPI_FAST_SEQ_DATA_REG);
- avail--;
- }
- }
-}
-
static inline void stfsm_load_seq(struct stfsm *fsm,
const struct stfsm_seq *seq)
{
@@ -772,6 +775,68 @@
}
}
+/*
+ * Clear the data FIFO
+ *
+ * Typically, this is only required during driver initialisation, where no
+ * assumptions can be made regarding the state of the FIFO.
+ *
+ * The process of clearing the FIFO is complicated by fact that while it is
+ * possible for the FIFO to contain an arbitrary number of bytes [1], the
+ * SPI_FAST_SEQ_STA register only reports the number of complete 32-bit words
+ * present. Furthermore, data can only be drained from the FIFO by reading
+ * complete 32-bit words.
+ *
+ * With this in mind, a two stage process is used to the clear the FIFO:
+ *
+ * 1. Read any complete 32-bit words from the FIFO, as reported by the
+ * SPI_FAST_SEQ_STA register.
+ *
+ * 2. Mop up any remaining bytes. At this point, it is not known if there
+ * are 0, 1, 2, or 3 bytes in the FIFO. To handle all cases, a dummy FSM
+ * sequence is used to load one byte at a time, until a complete 32-bit
+ * word is formed; at most, 4 bytes will need to be loaded.
+ *
+ * [1] It is theoretically possible for the FIFO to contain an arbitrary number
+ * of bits. However, since there are no known use-cases that leave
+ * incomplete bytes in the FIFO, only words and bytes are considered here.
+ */
+static void stfsm_clear_fifo(struct stfsm *fsm)
+{
+ const struct stfsm_seq *seq = &stfsm_seq_load_fifo_byte;
+ uint32_t words, i;
+
+ /* 1. Clear any 32-bit words */
+ words = stfsm_fifo_available(fsm);
+ if (words) {
+ for (i = 0; i < words; i++)
+ readl(fsm->base + SPI_FAST_SEQ_DATA_REG);
+ dev_dbg(fsm->dev, "cleared %d words from FIFO\n", words);
+ }
+
+ /*
+ * 2. Clear any remaining bytes
+ * - Load the FIFO, one byte at a time, until a complete 32-bit word
+ * is available.
+ */
+ for (i = 0, words = 0; i < 4 && !words; i++) {
+ stfsm_load_seq(fsm, seq);
+ stfsm_wait_seq(fsm);
+ words = stfsm_fifo_available(fsm);
+ }
+
+ /* - A single word must be available now */
+ if (words != 1) {
+ dev_err(fsm->dev, "failed to clear bytes from the data FIFO\n");
+ return;
+ }
+
+ /* - Read the 32-bit word */
+ readl(fsm->base + SPI_FAST_SEQ_DATA_REG);
+
+ dev_dbg(fsm->dev, "cleared %d byte(s) from the data FIFO\n", 4 - i);
+}
+
static int stfsm_write_fifo(struct stfsm *fsm, const uint32_t *buf,
uint32_t size)
{
@@ -1521,11 +1586,11 @@
uint32_t size_lb;
uint32_t size_mop;
uint32_t tmp[4];
+ uint32_t i;
uint32_t page_buf[FLASH_PAGESIZE_32];
uint8_t *t = (uint8_t *)&tmp;
const uint8_t *p;
int ret;
- int i;
dev_dbg(fsm->dev, "writing %d bytes to 0x%08x\n", size, offset);
@@ -1843,8 +1908,7 @@
uint32_t emi_freq;
uint32_t clk_div;
- /* TODO: Make this dynamic */
- emi_freq = STFSM_DEFAULT_EMI_FREQ;
+ emi_freq = clk_get_rate(fsm->clk);
/*
* Calculate clk_div - values between 2 and 128
@@ -1994,6 +2058,18 @@
return PTR_ERR(fsm->base);
}
+ fsm->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(fsm->clk)) {
+ dev_err(fsm->dev, "Couldn't find EMI clock.\n");
+ return PTR_ERR(fsm->clk);
+ }
+
+ ret = clk_prepare_enable(fsm->clk);
+ if (ret) {
+ dev_err(fsm->dev, "Failed to enable EMI clock.\n");
+ return ret;
+ }
+
mutex_init(&fsm->lock);
ret = stfsm_init(fsm);
@@ -2058,6 +2134,28 @@
return mtd_device_unregister(&fsm->mtd);
}
+#ifdef CONFIG_PM_SLEEP
+static int stfsmfsm_suspend(struct device *dev)
+{
+ struct stfsm *fsm = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(fsm->clk);
+
+ return 0;
+}
+
+static int stfsmfsm_resume(struct device *dev)
+{
+ struct stfsm *fsm = dev_get_drvdata(dev);
+
+ clk_prepare_enable(fsm->clk);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(stfsm_pm_ops, stfsmfsm_suspend, stfsmfsm_resume);
+
static const struct of_device_id stfsm_match[] = {
{ .compatible = "st,spi-fsm", },
{},
@@ -2070,6 +2168,7 @@
.driver = {
.name = "st-spi-fsm",
.of_match_table = stfsm_match,
+ .pm = &stfsm_pm_ops,
},
};
module_platform_driver(stfsm_driver);
diff --git a/drivers/mtd/maps/physmap_of.c b/drivers/mtd/maps/physmap_of.c
index f35cd20..ff26e97 100644
--- a/drivers/mtd/maps/physmap_of.c
+++ b/drivers/mtd/maps/physmap_of.c
@@ -269,6 +269,16 @@
info->list[i].mtd = obsolete_probe(dev,
&info->list[i].map);
}
+
+ /* Fall back to mapping region as ROM */
+ if (!info->list[i].mtd) {
+ dev_warn(&dev->dev,
+ "do_map_probe() failed for type %s\n",
+ probe_type);
+
+ info->list[i].mtd = do_map_probe("map_rom",
+ &info->list[i].map);
+ }
mtd_list[i] = info->list[i].mtd;
err = -ENXIO;
diff --git a/drivers/mtd/mtdblock.c b/drivers/mtd/mtdblock.c
index 485ea75..bb4c14f 100644
--- a/drivers/mtd/mtdblock.c
+++ b/drivers/mtd/mtdblock.c
@@ -45,8 +45,6 @@
enum { STATE_EMPTY, STATE_CLEAN, STATE_DIRTY } cache_state;
};
-static DEFINE_MUTEX(mtdblks_lock);
-
/*
* Cache stuff...
*
@@ -286,10 +284,8 @@
pr_debug("mtdblock_open\n");
- mutex_lock(&mtdblks_lock);
if (mtdblk->count) {
mtdblk->count++;
- mutex_unlock(&mtdblks_lock);
return 0;
}
@@ -302,8 +298,6 @@
mtdblk->cache_data = NULL;
}
- mutex_unlock(&mtdblks_lock);
-
pr_debug("ok\n");
return 0;
@@ -315,8 +309,6 @@
pr_debug("mtdblock_release\n");
- mutex_lock(&mtdblks_lock);
-
mutex_lock(&mtdblk->cache_mutex);
write_cached_data(mtdblk);
mutex_unlock(&mtdblk->cache_mutex);
@@ -331,8 +323,6 @@
vfree(mtdblk->cache_data);
}
- mutex_unlock(&mtdblks_lock);
-
pr_debug("ok\n");
}
diff --git a/drivers/mtd/mtdconcat.c b/drivers/mtd/mtdconcat.c
index b900056..d85c946 100644
--- a/drivers/mtd/mtdconcat.c
+++ b/drivers/mtd/mtdconcat.c
@@ -311,7 +311,8 @@
devops.len = subdev->size - to;
err = mtd_write_oob(subdev, to, &devops);
- ops->retlen += devops.oobretlen;
+ ops->retlen += devops.retlen;
+ ops->oobretlen += devops.oobretlen;
if (err)
return err;
diff --git a/drivers/mtd/mtdcore.c b/drivers/mtd/mtdcore.c
index 4c61187..52eea93 100644
--- a/drivers/mtd/mtdcore.c
+++ b/drivers/mtd/mtdcore.c
@@ -37,6 +37,7 @@
#include <linux/backing-dev.h>
#include <linux/gfp.h>
#include <linux/slab.h>
+#include <linux/reboot.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
@@ -365,6 +366,17 @@
.release = mtd_release,
};
+static int mtd_reboot_notifier(struct notifier_block *n, unsigned long state,
+ void *cmd)
+{
+ struct mtd_info *mtd;
+
+ mtd = container_of(n, struct mtd_info, reboot_notifier);
+ mtd->_reboot(mtd);
+
+ return NOTIFY_DONE;
+}
+
/**
* add_mtd_device - register an MTD device
* @mtd: pointer to new MTD device info structure
@@ -565,6 +577,19 @@
err = -ENODEV;
}
+ /*
+ * FIXME: some drivers unfortunately call this function more than once.
+ * So we have to check if we've already assigned the reboot notifier.
+ *
+ * Generally, we can make multiple calls work for most cases, but it
+ * does cause problems with parse_mtd_partitions() above (e.g.,
+ * cmdlineparts will register partitions more than once).
+ */
+ if (mtd->_reboot && !mtd->reboot_notifier.notifier_call) {
+ mtd->reboot_notifier.notifier_call = mtd_reboot_notifier;
+ register_reboot_notifier(&mtd->reboot_notifier);
+ }
+
return err;
}
EXPORT_SYMBOL_GPL(mtd_device_parse_register);
@@ -579,6 +604,9 @@
{
int err;
+ if (master->_reboot)
+ unregister_reboot_notifier(&master->reboot_notifier);
+
err = del_mtd_partitions(master);
if (err)
return err;
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 7d0150d..5b76a17 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -421,7 +421,7 @@
config MTD_NAND_FSL_ELBC
tristate "NAND support for Freescale eLBC controllers"
- depends on PPC_OF
+ depends on PPC
select FSL_LBC
help
Various Freescale chips, including the 8313, include a NAND Flash
@@ -524,4 +524,9 @@
help
Enables support for NAND Flash chips on Allwinner SoCs.
+config MTD_NAND_HISI504
+ tristate "Support for NAND controller on Hisilicon SoC Hip04"
+ help
+ Enables support for NAND controller on Hisilicon SoC Hip04.
+
endif # MTD_NAND
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index bd38f21..582bbd05 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -51,5 +51,6 @@
obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o
obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/
obj-$(CONFIG_MTD_NAND_SUNXI) += sunxi_nand.o
+obj-$(CONFIG_MTD_NAND_HISI504) += hisi504_nand.o
nand-objs := nand_base.o nand_bbt.o nand_timings.o
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/ams-delta.c
index f1d555c..842f8fe 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/ams-delta.c
@@ -183,7 +183,7 @@
return -ENXIO;
/* Allocate memory for MTD device structure and private data */
- ams_delta_mtd = kmalloc(sizeof(struct mtd_info) +
+ ams_delta_mtd = kzalloc(sizeof(struct mtd_info) +
sizeof(struct nand_chip), GFP_KERNEL);
if (!ams_delta_mtd) {
printk (KERN_WARNING "Unable to allocate E3 NAND MTD device structure.\n");
@@ -196,10 +196,6 @@
/* Get pointer to private data */
this = (struct nand_chip *) (&ams_delta_mtd[1]);
- /* Initialize structures */
- memset(ams_delta_mtd, 0, sizeof(struct mtd_info));
- memset(this, 0, sizeof(struct nand_chip));
-
/* Link the private data with the MTD structure */
ams_delta_mtd->priv = this;
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index a345e7b..d93c849 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -63,6 +63,10 @@
#include "atmel_nand_ecc.h" /* Hardware ECC registers */
#include "atmel_nand_nfc.h" /* Nand Flash Controller definition */
+struct atmel_nand_caps {
+ bool pmecc_correct_erase_page;
+};
+
/* oob layout for large page size
* bad block info is on bytes 0 and 1
* the bytes have to be consecutives to avoid
@@ -124,6 +128,7 @@
struct atmel_nfc *nfc;
+ struct atmel_nand_caps *caps;
bool has_pmecc;
u8 pmecc_corr_cap;
u16 pmecc_sector_size;
@@ -847,7 +852,11 @@
struct atmel_nand_host *host = nand_chip->priv;
int i, err_nbr;
uint8_t *buf_pos;
- int total_err = 0;
+ int max_bitflips = 0;
+
+ /* If can correct bitfilps from erased page, do the normal check */
+ if (host->caps->pmecc_correct_erase_page)
+ goto normal_check;
for (i = 0; i < nand_chip->ecc.total; i++)
if (ecc[i] != 0xff)
@@ -874,13 +883,13 @@
pmecc_correct_data(mtd, buf_pos, ecc, i,
nand_chip->ecc.bytes, err_nbr);
mtd->ecc_stats.corrected += err_nbr;
- total_err += err_nbr;
+ max_bitflips = max_t(int, max_bitflips, err_nbr);
}
}
pmecc_stat >>= 1;
}
- return total_err;
+ return max_bitflips;
}
static void pmecc_enable(struct atmel_nand_host *host, int ecc_op)
@@ -1474,6 +1483,8 @@
ecc_writel(host->ecc, CR, ATMEL_ECC_RST);
}
+static const struct of_device_id atmel_nand_dt_ids[];
+
static int atmel_of_init_port(struct atmel_nand_host *host,
struct device_node *np)
{
@@ -1483,6 +1494,9 @@
struct atmel_nand_data *board = &host->board;
enum of_gpio_flags flags = 0;
+ host->caps = (struct atmel_nand_caps *)
+ of_match_device(atmel_nand_dt_ids, host->dev)->data;
+
if (of_property_read_u32(np, "atmel,nand-addr-offset", &val) == 0) {
if (val >= 32) {
dev_err(host->dev, "invalid addr-offset %u\n", val);
@@ -2288,8 +2302,17 @@
return 0;
}
+static struct atmel_nand_caps at91rm9200_caps = {
+ .pmecc_correct_erase_page = false,
+};
+
+static struct atmel_nand_caps sama5d4_caps = {
+ .pmecc_correct_erase_page = true,
+};
+
static const struct of_device_id atmel_nand_dt_ids[] = {
- { .compatible = "atmel,at91rm9200-nand" },
+ { .compatible = "atmel,at91rm9200-nand", .data = &at91rm9200_caps },
+ { .compatible = "atmel,sama5d4-nand", .data = &sama5d4_caps },
{ /* sentinel */ }
};
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index b3b7ca1..f44c606 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -1041,7 +1041,7 @@
index_addr(denali, mode | ((addr >> 16) << 8), 0x2200);
/* 3. set memory low address bits 23:8 */
- index_addr(denali, mode | ((addr & 0xff) << 8), 0x2300);
+ index_addr(denali, mode | ((addr & 0xffff) << 8), 0x2300);
/* 4. interrupt when complete, burst len = 64 bytes */
index_addr(denali, mode | 0x14000, 0x2400);
@@ -1328,35 +1328,6 @@
break;
}
}
-
-/* stubs for ECC functions not used by the NAND core */
-static int denali_ecc_calculate(struct mtd_info *mtd, const uint8_t *data,
- uint8_t *ecc_code)
-{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
-
- dev_err(denali->dev, "denali_ecc_calculate called unexpectedly\n");
- BUG();
- return -EIO;
-}
-
-static int denali_ecc_correct(struct mtd_info *mtd, uint8_t *data,
- uint8_t *read_ecc, uint8_t *calc_ecc)
-{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
-
- dev_err(denali->dev, "denali_ecc_correct called unexpectedly\n");
- BUG();
- return -EIO;
-}
-
-static void denali_ecc_hwctl(struct mtd_info *mtd, int mode)
-{
- struct denali_nand_info *denali = mtd_to_denali(mtd);
-
- dev_err(denali->dev, "denali_ecc_hwctl called unexpectedly\n");
- BUG();
-}
/* end NAND core entry points */
/* Initialization code to bring the device up to a known good state */
@@ -1609,15 +1580,6 @@
denali->totalblks = denali->mtd.size >> denali->nand.phys_erase_shift;
denali->blksperchip = denali->totalblks / denali->nand.numchips;
- /*
- * These functions are required by the NAND core framework, otherwise,
- * the NAND core will assert. However, we don't need them, so we'll stub
- * them out.
- */
- denali->nand.ecc.calculate = denali_ecc_calculate;
- denali->nand.ecc.correct = denali_ecc_correct;
- denali->nand.ecc.hwctl = denali_ecc_hwctl;
-
/* override the default read operations */
denali->nand.ecc.size = ECC_SECTOR_SIZE * denali->devnum;
denali->nand.ecc.read_page = denali_read_page;
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
index 4f3851a..33f3c3c 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
@@ -1294,14 +1294,6 @@
* ecc.read_page or ecc.read_page_raw function. Thus, the fact that MTD wants an
* ECC-based or raw view of the page is implicit in which function it calls
* (there is a similar pair of ECC-based/raw functions for writing).
- *
- * FIXME: The following paragraph is incorrect, now that there exist
- * ecc.read_oob_raw and ecc.write_oob_raw functions.
- *
- * Since MTD assumes the OOB is not covered by ECC, there is no pair of
- * ECC-based/raw functions for reading or or writing the OOB. The fact that the
- * caller wants an ECC-based or raw view of the page is not propagated down to
- * this driver.
*/
static int gpmi_ecc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
int page)
@@ -2029,7 +2021,6 @@
exit_nfc_init:
release_resources(this);
exit_acquire_resources:
- dev_err(this->dev, "driver registration failed: %d\n", ret);
return ret;
}
diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/hisi504_nand.c
new file mode 100644
index 0000000..289ad3a
--- /dev/null
+++ b/drivers/mtd/nand/hisi504_nand.c
@@ -0,0 +1,891 @@
+/*
+ * Hisilicon NAND Flash controller driver
+ *
+ * Copyright © 2012-2014 HiSilicon Technologies Co., Ltd.
+ * http://www.hisilicon.com
+ *
+ * Author: Zhou Wang <wangzhou.bry@gmail.com>
+ * The initial developer of the original code is Zhiyong Cai
+ * <caizhiyong@huawei.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/of.h>
+#include <linux/of_mtd.h>
+#include <linux/mtd/mtd.h>
+#include <linux/sizes.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/nand.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+
+#define HINFC504_MAX_CHIP (4)
+#define HINFC504_W_LATCH (5)
+#define HINFC504_R_LATCH (7)
+#define HINFC504_RW_LATCH (3)
+
+#define HINFC504_NFC_TIMEOUT (2 * HZ)
+#define HINFC504_NFC_PM_TIMEOUT (1 * HZ)
+#define HINFC504_NFC_DMA_TIMEOUT (5 * HZ)
+#define HINFC504_CHIP_DELAY (25)
+
+#define HINFC504_REG_BASE_ADDRESS_LEN (0x100)
+#define HINFC504_BUFFER_BASE_ADDRESS_LEN (2048 + 128)
+
+#define HINFC504_ADDR_CYCLE_MASK 0x4
+
+#define HINFC504_CON 0x00
+#define HINFC504_CON_OP_MODE_NORMAL BIT(0)
+#define HINFC504_CON_PAGEISZE_SHIFT (1)
+#define HINFC504_CON_PAGESIZE_MASK (0x07)
+#define HINFC504_CON_BUS_WIDTH BIT(4)
+#define HINFC504_CON_READY_BUSY_SEL BIT(8)
+#define HINFC504_CON_ECCTYPE_SHIFT (9)
+#define HINFC504_CON_ECCTYPE_MASK (0x07)
+
+#define HINFC504_PWIDTH 0x04
+#define SET_HINFC504_PWIDTH(_w_lcnt, _r_lcnt, _rw_hcnt) \
+ ((_w_lcnt) | (((_r_lcnt) & 0x0F) << 4) | (((_rw_hcnt) & 0x0F) << 8))
+
+#define HINFC504_CMD 0x0C
+#define HINFC504_ADDRL 0x10
+#define HINFC504_ADDRH 0x14
+#define HINFC504_DATA_NUM 0x18
+
+#define HINFC504_OP 0x1C
+#define HINFC504_OP_READ_DATA_EN BIT(1)
+#define HINFC504_OP_WAIT_READY_EN BIT(2)
+#define HINFC504_OP_CMD2_EN BIT(3)
+#define HINFC504_OP_WRITE_DATA_EN BIT(4)
+#define HINFC504_OP_ADDR_EN BIT(5)
+#define HINFC504_OP_CMD1_EN BIT(6)
+#define HINFC504_OP_NF_CS_SHIFT (7)
+#define HINFC504_OP_NF_CS_MASK (3)
+#define HINFC504_OP_ADDR_CYCLE_SHIFT (9)
+#define HINFC504_OP_ADDR_CYCLE_MASK (7)
+
+#define HINFC504_STATUS 0x20
+#define HINFC504_READY BIT(0)
+
+#define HINFC504_INTEN 0x24
+#define HINFC504_INTEN_DMA BIT(9)
+#define HINFC504_INTEN_UE BIT(6)
+#define HINFC504_INTEN_CE BIT(5)
+
+#define HINFC504_INTS 0x28
+#define HINFC504_INTS_DMA BIT(9)
+#define HINFC504_INTS_UE BIT(6)
+#define HINFC504_INTS_CE BIT(5)
+
+#define HINFC504_INTCLR 0x2C
+#define HINFC504_INTCLR_DMA BIT(9)
+#define HINFC504_INTCLR_UE BIT(6)
+#define HINFC504_INTCLR_CE BIT(5)
+
+#define HINFC504_ECC_STATUS 0x5C
+#define HINFC504_ECC_16_BIT_SHIFT 12
+
+#define HINFC504_DMA_CTRL 0x60
+#define HINFC504_DMA_CTRL_DMA_START BIT(0)
+#define HINFC504_DMA_CTRL_WE BIT(1)
+#define HINFC504_DMA_CTRL_DATA_AREA_EN BIT(2)
+#define HINFC504_DMA_CTRL_OOB_AREA_EN BIT(3)
+#define HINFC504_DMA_CTRL_BURST4_EN BIT(4)
+#define HINFC504_DMA_CTRL_BURST8_EN BIT(5)
+#define HINFC504_DMA_CTRL_BURST16_EN BIT(6)
+#define HINFC504_DMA_CTRL_ADDR_NUM_SHIFT (7)
+#define HINFC504_DMA_CTRL_ADDR_NUM_MASK (1)
+#define HINFC504_DMA_CTRL_CS_SHIFT (8)
+#define HINFC504_DMA_CTRL_CS_MASK (0x03)
+
+#define HINFC504_DMA_ADDR_DATA 0x64
+#define HINFC504_DMA_ADDR_OOB 0x68
+
+#define HINFC504_DMA_LEN 0x6C
+#define HINFC504_DMA_LEN_OOB_SHIFT (16)
+#define HINFC504_DMA_LEN_OOB_MASK (0xFFF)
+
+#define HINFC504_DMA_PARA 0x70
+#define HINFC504_DMA_PARA_DATA_RW_EN BIT(0)
+#define HINFC504_DMA_PARA_OOB_RW_EN BIT(1)
+#define HINFC504_DMA_PARA_DATA_EDC_EN BIT(2)
+#define HINFC504_DMA_PARA_OOB_EDC_EN BIT(3)
+#define HINFC504_DMA_PARA_DATA_ECC_EN BIT(4)
+#define HINFC504_DMA_PARA_OOB_ECC_EN BIT(5)
+
+#define HINFC_VERSION 0x74
+#define HINFC504_LOG_READ_ADDR 0x7C
+#define HINFC504_LOG_READ_LEN 0x80
+
+#define HINFC504_NANDINFO_LEN 0x10
+
+struct hinfc_host {
+ struct nand_chip chip;
+ struct mtd_info mtd;
+ struct device *dev;
+ void __iomem *iobase;
+ void __iomem *mmio;
+ struct completion cmd_complete;
+ unsigned int offset;
+ unsigned int command;
+ int chipselect;
+ unsigned int addr_cycle;
+ u32 addr_value[2];
+ u32 cache_addr_value[2];
+ char *buffer;
+ dma_addr_t dma_buffer;
+ dma_addr_t dma_oob;
+ int version;
+ unsigned int irq_status; /* interrupt status */
+};
+
+static inline unsigned int hinfc_read(struct hinfc_host *host, unsigned int reg)
+{
+ return readl(host->iobase + reg);
+}
+
+static inline void hinfc_write(struct hinfc_host *host, unsigned int value,
+ unsigned int reg)
+{
+ writel(value, host->iobase + reg);
+}
+
+static void wait_controller_finished(struct hinfc_host *host)
+{
+ unsigned long timeout = jiffies + HINFC504_NFC_TIMEOUT;
+ int val;
+
+ while (time_before(jiffies, timeout)) {
+ val = hinfc_read(host, HINFC504_STATUS);
+ if (host->command == NAND_CMD_ERASE2) {
+ /* nfc is ready */
+ while (!(val & HINFC504_READY)) {
+ usleep_range(500, 1000);
+ val = hinfc_read(host, HINFC504_STATUS);
+ }
+ return;
+ }
+
+ if (val & HINFC504_READY)
+ return;
+ }
+
+ /* wait cmd timeout */
+ dev_err(host->dev, "Wait NAND controller exec cmd timeout.\n");
+}
+
+static void hisi_nfc_dma_transfer(struct hinfc_host *host, int todev)
+{
+ struct mtd_info *mtd = &host->mtd;
+ struct nand_chip *chip = mtd->priv;
+ unsigned long val;
+ int ret;
+
+ hinfc_write(host, host->dma_buffer, HINFC504_DMA_ADDR_DATA);
+ hinfc_write(host, host->dma_oob, HINFC504_DMA_ADDR_OOB);
+
+ if (chip->ecc.mode == NAND_ECC_NONE) {
+ hinfc_write(host, ((mtd->oobsize & HINFC504_DMA_LEN_OOB_MASK)
+ << HINFC504_DMA_LEN_OOB_SHIFT), HINFC504_DMA_LEN);
+
+ hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
+ | HINFC504_DMA_PARA_OOB_RW_EN, HINFC504_DMA_PARA);
+ } else {
+ if (host->command == NAND_CMD_READOOB)
+ hinfc_write(host, HINFC504_DMA_PARA_OOB_RW_EN
+ | HINFC504_DMA_PARA_OOB_EDC_EN
+ | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
+ else
+ hinfc_write(host, HINFC504_DMA_PARA_DATA_RW_EN
+ | HINFC504_DMA_PARA_OOB_RW_EN
+ | HINFC504_DMA_PARA_DATA_EDC_EN
+ | HINFC504_DMA_PARA_OOB_EDC_EN
+ | HINFC504_DMA_PARA_DATA_ECC_EN
+ | HINFC504_DMA_PARA_OOB_ECC_EN, HINFC504_DMA_PARA);
+
+ }
+
+ val = (HINFC504_DMA_CTRL_DMA_START | HINFC504_DMA_CTRL_BURST4_EN
+ | HINFC504_DMA_CTRL_BURST8_EN | HINFC504_DMA_CTRL_BURST16_EN
+ | HINFC504_DMA_CTRL_DATA_AREA_EN | HINFC504_DMA_CTRL_OOB_AREA_EN
+ | ((host->addr_cycle == 4 ? 1 : 0)
+ << HINFC504_DMA_CTRL_ADDR_NUM_SHIFT)
+ | ((host->chipselect & HINFC504_DMA_CTRL_CS_MASK)
+ << HINFC504_DMA_CTRL_CS_SHIFT));
+
+ if (todev)
+ val |= HINFC504_DMA_CTRL_WE;
+
+ init_completion(&host->cmd_complete);
+
+ hinfc_write(host, val, HINFC504_DMA_CTRL);
+ ret = wait_for_completion_timeout(&host->cmd_complete,
+ HINFC504_NFC_DMA_TIMEOUT);
+
+ if (!ret) {
+ dev_err(host->dev, "DMA operation(irq) timeout!\n");
+ /* sanity check */
+ val = hinfc_read(host, HINFC504_DMA_CTRL);
+ if (!(val & HINFC504_DMA_CTRL_DMA_START))
+ dev_err(host->dev, "DMA is already done but without irq ACK!\n");
+ else
+ dev_err(host->dev, "DMA is really timeout!\n");
+ }
+}
+
+static int hisi_nfc_send_cmd_pageprog(struct hinfc_host *host)
+{
+ host->addr_value[0] &= 0xffff0000;
+
+ hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
+ hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
+ hinfc_write(host, NAND_CMD_PAGEPROG << 8 | NAND_CMD_SEQIN,
+ HINFC504_CMD);
+
+ hisi_nfc_dma_transfer(host, 1);
+
+ return 0;
+}
+
+static int hisi_nfc_send_cmd_readstart(struct hinfc_host *host)
+{
+ struct mtd_info *mtd = &host->mtd;
+
+ if ((host->addr_value[0] == host->cache_addr_value[0]) &&
+ (host->addr_value[1] == host->cache_addr_value[1]))
+ return 0;
+
+ host->addr_value[0] &= 0xffff0000;
+
+ hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
+ hinfc_write(host, host->addr_value[1], HINFC504_ADDRH);
+ hinfc_write(host, NAND_CMD_READSTART << 8 | NAND_CMD_READ0,
+ HINFC504_CMD);
+
+ hinfc_write(host, 0, HINFC504_LOG_READ_ADDR);
+ hinfc_write(host, mtd->writesize + mtd->oobsize,
+ HINFC504_LOG_READ_LEN);
+
+ hisi_nfc_dma_transfer(host, 0);
+
+ host->cache_addr_value[0] = host->addr_value[0];
+ host->cache_addr_value[1] = host->addr_value[1];
+
+ return 0;
+}
+
+static int hisi_nfc_send_cmd_erase(struct hinfc_host *host)
+{
+ hinfc_write(host, host->addr_value[0], HINFC504_ADDRL);
+ hinfc_write(host, (NAND_CMD_ERASE2 << 8) | NAND_CMD_ERASE1,
+ HINFC504_CMD);
+
+ hinfc_write(host, HINFC504_OP_WAIT_READY_EN
+ | HINFC504_OP_CMD2_EN
+ | HINFC504_OP_CMD1_EN
+ | HINFC504_OP_ADDR_EN
+ | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
+ << HINFC504_OP_NF_CS_SHIFT)
+ | ((host->addr_cycle & HINFC504_OP_ADDR_CYCLE_MASK)
+ << HINFC504_OP_ADDR_CYCLE_SHIFT),
+ HINFC504_OP);
+
+ wait_controller_finished(host);
+
+ return 0;
+}
+
+static int hisi_nfc_send_cmd_readid(struct hinfc_host *host)
+{
+ hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
+ hinfc_write(host, NAND_CMD_READID, HINFC504_CMD);
+ hinfc_write(host, 0, HINFC504_ADDRL);
+
+ hinfc_write(host, HINFC504_OP_CMD1_EN | HINFC504_OP_ADDR_EN
+ | HINFC504_OP_READ_DATA_EN
+ | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
+ << HINFC504_OP_NF_CS_SHIFT)
+ | 1 << HINFC504_OP_ADDR_CYCLE_SHIFT, HINFC504_OP);
+
+ wait_controller_finished(host);
+
+ return 0;
+}
+
+static int hisi_nfc_send_cmd_status(struct hinfc_host *host)
+{
+ hinfc_write(host, HINFC504_NANDINFO_LEN, HINFC504_DATA_NUM);
+ hinfc_write(host, NAND_CMD_STATUS, HINFC504_CMD);
+ hinfc_write(host, HINFC504_OP_CMD1_EN
+ | HINFC504_OP_READ_DATA_EN
+ | ((host->chipselect & HINFC504_OP_NF_CS_MASK)
+ << HINFC504_OP_NF_CS_SHIFT),
+ HINFC504_OP);
+
+ wait_controller_finished(host);
+
+ return 0;
+}
+
+static int hisi_nfc_send_cmd_reset(struct hinfc_host *host, int chipselect)
+{
+ hinfc_write(host, NAND_CMD_RESET, HINFC504_CMD);
+
+ hinfc_write(host, HINFC504_OP_CMD1_EN
+ | ((chipselect & HINFC504_OP_NF_CS_MASK)
+ << HINFC504_OP_NF_CS_SHIFT)
+ | HINFC504_OP_WAIT_READY_EN,
+ HINFC504_OP);
+
+ wait_controller_finished(host);
+
+ return 0;
+}
+
+static void hisi_nfc_select_chip(struct mtd_info *mtd, int chipselect)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+
+ if (chipselect < 0)
+ return;
+
+ host->chipselect = chipselect;
+}
+
+static uint8_t hisi_nfc_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+
+ if (host->command == NAND_CMD_STATUS)
+ return *(uint8_t *)(host->mmio);
+
+ host->offset++;
+
+ if (host->command == NAND_CMD_READID)
+ return *(uint8_t *)(host->mmio + host->offset - 1);
+
+ return *(uint8_t *)(host->buffer + host->offset - 1);
+}
+
+static u16 hisi_nfc_read_word(struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+
+ host->offset += 2;
+ return *(u16 *)(host->buffer + host->offset - 2);
+}
+
+static void
+hisi_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+
+ memcpy(host->buffer + host->offset, buf, len);
+ host->offset += len;
+}
+
+static void hisi_nfc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+
+ memcpy(buf, host->buffer + host->offset, len);
+ host->offset += len;
+}
+
+static void set_addr(struct mtd_info *mtd, int column, int page_addr)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+ unsigned int command = host->command;
+
+ host->addr_cycle = 0;
+ host->addr_value[0] = 0;
+ host->addr_value[1] = 0;
+
+ /* Serially input address */
+ if (column != -1) {
+ /* Adjust columns for 16 bit buswidth */
+ if (chip->options & NAND_BUSWIDTH_16 &&
+ !nand_opcode_8bits(command))
+ column >>= 1;
+
+ host->addr_value[0] = column & 0xffff;
+ host->addr_cycle = 2;
+ }
+ if (page_addr != -1) {
+ host->addr_value[0] |= (page_addr & 0xffff)
+ << (host->addr_cycle * 8);
+ host->addr_cycle += 2;
+ /* One more address cycle for devices > 128MiB */
+ if (chip->chipsize > (128 << 20)) {
+ host->addr_cycle += 1;
+ if (host->command == NAND_CMD_ERASE1)
+ host->addr_value[0] |= ((page_addr >> 16) & 0xff) << 16;
+ else
+ host->addr_value[1] |= ((page_addr >> 16) & 0xff);
+ }
+ }
+}
+
+static void hisi_nfc_cmdfunc(struct mtd_info *mtd, unsigned command, int column,
+ int page_addr)
+{
+ struct nand_chip *chip = mtd->priv;
+ struct hinfc_host *host = chip->priv;
+ int is_cache_invalid = 1;
+ unsigned int flag = 0;
+
+ host->command = command;
+
+ switch (command) {
+ case NAND_CMD_READ0:
+ case NAND_CMD_READOOB:
+ if (command == NAND_CMD_READ0)
+ host->offset = column;
+ else
+ host->offset = column + mtd->writesize;
+
+ is_cache_invalid = 0;
+ set_addr(mtd, column, page_addr);
+ hisi_nfc_send_cmd_readstart(host);
+ break;
+
+ case NAND_CMD_SEQIN:
+ host->offset = column;
+ set_addr(mtd, column, page_addr);
+ break;
+
+ case NAND_CMD_ERASE1:
+ set_addr(mtd, column, page_addr);
+ break;
+
+ case NAND_CMD_PAGEPROG:
+ hisi_nfc_send_cmd_pageprog(host);
+ break;
+
+ case NAND_CMD_ERASE2:
+ hisi_nfc_send_cmd_erase(host);
+ break;
+
+ case NAND_CMD_READID:
+ host->offset = column;
+ memset(host->mmio, 0, 0x10);
+ hisi_nfc_send_cmd_readid(host);
+ break;
+
+ case NAND_CMD_STATUS:
+ flag = hinfc_read(host, HINFC504_CON);
+ if (chip->ecc.mode == NAND_ECC_HW)
+ hinfc_write(host,
+ flag & ~(HINFC504_CON_ECCTYPE_MASK <<
+ HINFC504_CON_ECCTYPE_SHIFT), HINFC504_CON);
+
+ host->offset = 0;
+ memset(host->mmio, 0, 0x10);
+ hisi_nfc_send_cmd_status(host);
+ hinfc_write(host, flag, HINFC504_CON);
+ break;
+
+ case NAND_CMD_RESET:
+ hisi_nfc_send_cmd_reset(host, host->chipselect);
+ break;
+
+ default:
+ dev_err(host->dev, "Error: unsupported cmd(cmd=%x, col=%x, page=%x)\n",
+ command, column, page_addr);
+ }
+
+ if (is_cache_invalid) {
+ host->cache_addr_value[0] = ~0;
+ host->cache_addr_value[1] = ~0;
+ }
+}
+
+static irqreturn_t hinfc_irq_handle(int irq, void *devid)
+{
+ struct hinfc_host *host = devid;
+ unsigned int flag;
+
+ flag = hinfc_read(host, HINFC504_INTS);
+ /* store interrupts state */
+ host->irq_status |= flag;
+
+ if (flag & HINFC504_INTS_DMA) {
+ hinfc_write(host, HINFC504_INTCLR_DMA, HINFC504_INTCLR);
+ complete(&host->cmd_complete);
+ } else if (flag & HINFC504_INTS_CE) {
+ hinfc_write(host, HINFC504_INTCLR_CE, HINFC504_INTCLR);
+ } else if (flag & HINFC504_INTS_UE) {
+ hinfc_write(host, HINFC504_INTCLR_UE, HINFC504_INTCLR);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int hisi_nand_read_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
+{
+ struct hinfc_host *host = chip->priv;
+ int max_bitflips = 0, stat = 0, stat_max = 0, status_ecc;
+ int stat_1, stat_2;
+
+ chip->read_buf(mtd, buf, mtd->writesize);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ /* errors which can not be corrected by ECC */
+ if (host->irq_status & HINFC504_INTS_UE) {
+ mtd->ecc_stats.failed++;
+ } else if (host->irq_status & HINFC504_INTS_CE) {
+ /* TODO: need add other ECC modes! */
+ switch (chip->ecc.strength) {
+ case 16:
+ status_ecc = hinfc_read(host, HINFC504_ECC_STATUS) >>
+ HINFC504_ECC_16_BIT_SHIFT & 0x0fff;
+ stat_2 = status_ecc & 0x3f;
+ stat_1 = status_ecc >> 6 & 0x3f;
+ stat = stat_1 + stat_2;
+ stat_max = max_t(int, stat_1, stat_2);
+ }
+ mtd->ecc_stats.corrected += stat;
+ max_bitflips = max_t(int, max_bitflips, stat_max);
+ }
+ host->irq_status = 0;
+
+ return max_bitflips;
+}
+
+static int hisi_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+ int page)
+{
+ struct hinfc_host *host = chip->priv;
+
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ if (host->irq_status & HINFC504_INTS_UE) {
+ host->irq_status = 0;
+ return -EBADMSG;
+ }
+
+ host->irq_status = 0;
+ return 0;
+}
+
+static int hisi_nand_write_page_hwecc(struct mtd_info *mtd,
+ struct nand_chip *chip, const uint8_t *buf, int oob_required)
+{
+ chip->write_buf(mtd, buf, mtd->writesize);
+ if (oob_required)
+ chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return 0;
+}
+
+static void hisi_nfc_host_init(struct hinfc_host *host)
+{
+ struct nand_chip *chip = &host->chip;
+ unsigned int flag = 0;
+
+ host->version = hinfc_read(host, HINFC_VERSION);
+ host->addr_cycle = 0;
+ host->addr_value[0] = 0;
+ host->addr_value[1] = 0;
+ host->cache_addr_value[0] = ~0;
+ host->cache_addr_value[1] = ~0;
+ host->chipselect = 0;
+
+ /* default page size: 2K, ecc_none. need modify */
+ flag = HINFC504_CON_OP_MODE_NORMAL | HINFC504_CON_READY_BUSY_SEL
+ | ((0x001 & HINFC504_CON_PAGESIZE_MASK)
+ << HINFC504_CON_PAGEISZE_SHIFT)
+ | ((0x0 & HINFC504_CON_ECCTYPE_MASK)
+ << HINFC504_CON_ECCTYPE_SHIFT)
+ | ((chip->options & NAND_BUSWIDTH_16) ?
+ HINFC504_CON_BUS_WIDTH : 0);
+ hinfc_write(host, flag, HINFC504_CON);
+
+ memset(host->mmio, 0xff, HINFC504_BUFFER_BASE_ADDRESS_LEN);
+
+ hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
+ HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
+
+ /* enable DMA irq */
+ hinfc_write(host, HINFC504_INTEN_DMA, HINFC504_INTEN);
+}
+
+static struct nand_ecclayout nand_ecc_2K_16bits = {
+ .oobavail = 6,
+ .oobfree = { {2, 6} },
+};
+
+static int hisi_nfc_ecc_probe(struct hinfc_host *host)
+{
+ unsigned int flag;
+ int size, strength, ecc_bits;
+ struct device *dev = host->dev;
+ struct nand_chip *chip = &host->chip;
+ struct mtd_info *mtd = &host->mtd;
+ struct device_node *np = host->dev->of_node;
+
+ size = of_get_nand_ecc_step_size(np);
+ strength = of_get_nand_ecc_strength(np);
+ if (size != 1024) {
+ dev_err(dev, "error ecc size: %d\n", size);
+ return -EINVAL;
+ }
+
+ if ((size == 1024) && ((strength != 8) && (strength != 16) &&
+ (strength != 24) && (strength != 40))) {
+ dev_err(dev, "ecc size and strength do not match\n");
+ return -EINVAL;
+ }
+
+ chip->ecc.size = size;
+ chip->ecc.strength = strength;
+
+ chip->ecc.read_page = hisi_nand_read_page_hwecc;
+ chip->ecc.read_oob = hisi_nand_read_oob;
+ chip->ecc.write_page = hisi_nand_write_page_hwecc;
+
+ switch (chip->ecc.strength) {
+ case 16:
+ ecc_bits = 6;
+ if (mtd->writesize == 2048)
+ chip->ecc.layout = &nand_ecc_2K_16bits;
+
+ /* TODO: add more page size support */
+ break;
+
+ /* TODO: add more ecc strength support */
+ default:
+ dev_err(dev, "not support strength: %d\n", chip->ecc.strength);
+ return -EINVAL;
+ }
+
+ flag = hinfc_read(host, HINFC504_CON);
+ /* add ecc type configure */
+ flag |= ((ecc_bits & HINFC504_CON_ECCTYPE_MASK)
+ << HINFC504_CON_ECCTYPE_SHIFT);
+ hinfc_write(host, flag, HINFC504_CON);
+
+ /* enable ecc irq */
+ flag = hinfc_read(host, HINFC504_INTEN) & 0xfff;
+ hinfc_write(host, flag | HINFC504_INTEN_UE | HINFC504_INTEN_CE,
+ HINFC504_INTEN);
+
+ return 0;
+}
+
+static int hisi_nfc_probe(struct platform_device *pdev)
+{
+ int ret = 0, irq, buswidth, flag, max_chips = HINFC504_MAX_CHIP;
+ struct device *dev = &pdev->dev;
+ struct hinfc_host *host;
+ struct nand_chip *chip;
+ struct mtd_info *mtd;
+ struct resource *res;
+ struct device_node *np = dev->of_node;
+ struct mtd_part_parser_data ppdata;
+
+ host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
+ if (!host)
+ return -ENOMEM;
+ host->dev = dev;
+
+ platform_set_drvdata(pdev, host);
+ chip = &host->chip;
+ mtd = &host->mtd;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "no IRQ resource defined\n");
+ ret = -ENXIO;
+ goto err_res;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ host->iobase = devm_ioremap_resource(dev, res);
+ if (IS_ERR(host->iobase)) {
+ ret = PTR_ERR(host->iobase);
+ goto err_res;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ host->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(host->mmio)) {
+ ret = PTR_ERR(host->mmio);
+ dev_err(dev, "devm_ioremap_resource[1] fail\n");
+ goto err_res;
+ }
+
+ mtd->priv = chip;
+ mtd->owner = THIS_MODULE;
+ mtd->name = "hisi_nand";
+ mtd->dev.parent = &pdev->dev;
+
+ chip->priv = host;
+ chip->cmdfunc = hisi_nfc_cmdfunc;
+ chip->select_chip = hisi_nfc_select_chip;
+ chip->read_byte = hisi_nfc_read_byte;
+ chip->read_word = hisi_nfc_read_word;
+ chip->write_buf = hisi_nfc_write_buf;
+ chip->read_buf = hisi_nfc_read_buf;
+ chip->chip_delay = HINFC504_CHIP_DELAY;
+
+ chip->ecc.mode = of_get_nand_ecc_mode(np);
+
+ buswidth = of_get_nand_bus_width(np);
+ if (buswidth == 16)
+ chip->options |= NAND_BUSWIDTH_16;
+
+ hisi_nfc_host_init(host);
+
+ ret = devm_request_irq(dev, irq, hinfc_irq_handle, IRQF_DISABLED,
+ "nandc", host);
+ if (ret) {
+ dev_err(dev, "failed to request IRQ\n");
+ goto err_res;
+ }
+
+ ret = nand_scan_ident(mtd, max_chips, NULL);
+ if (ret) {
+ ret = -ENODEV;
+ goto err_res;
+ }
+
+ host->buffer = dmam_alloc_coherent(dev, mtd->writesize + mtd->oobsize,
+ &host->dma_buffer, GFP_KERNEL);
+ if (!host->buffer) {
+ ret = -ENOMEM;
+ goto err_res;
+ }
+
+ host->dma_oob = host->dma_buffer + mtd->writesize;
+ memset(host->buffer, 0xff, mtd->writesize + mtd->oobsize);
+
+ flag = hinfc_read(host, HINFC504_CON);
+ flag &= ~(HINFC504_CON_PAGESIZE_MASK << HINFC504_CON_PAGEISZE_SHIFT);
+ switch (mtd->writesize) {
+ case 2048:
+ flag |= (0x001 << HINFC504_CON_PAGEISZE_SHIFT); break;
+ /*
+ * TODO: add more pagesize support,
+ * default pagesize has been set in hisi_nfc_host_init
+ */
+ default:
+ dev_err(dev, "NON-2KB page size nand flash\n");
+ ret = -EINVAL;
+ goto err_res;
+ }
+ hinfc_write(host, flag, HINFC504_CON);
+
+ if (chip->ecc.mode == NAND_ECC_HW)
+ hisi_nfc_ecc_probe(host);
+
+ ret = nand_scan_tail(mtd);
+ if (ret) {
+ dev_err(dev, "nand_scan_tail failed: %d\n", ret);
+ goto err_res;
+ }
+
+ ppdata.of_node = np;
+ ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
+ if (ret) {
+ dev_err(dev, "Err MTD partition=%d\n", ret);
+ goto err_mtd;
+ }
+
+ return 0;
+
+err_mtd:
+ nand_release(mtd);
+err_res:
+ return ret;
+}
+
+static int hisi_nfc_remove(struct platform_device *pdev)
+{
+ struct hinfc_host *host = platform_get_drvdata(pdev);
+ struct mtd_info *mtd = &host->mtd;
+
+ nand_release(mtd);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int hisi_nfc_suspend(struct device *dev)
+{
+ struct hinfc_host *host = dev_get_drvdata(dev);
+ unsigned long timeout = jiffies + HINFC504_NFC_PM_TIMEOUT;
+
+ while (time_before(jiffies, timeout)) {
+ if (((hinfc_read(host, HINFC504_STATUS) & 0x1) == 0x0) &&
+ (hinfc_read(host, HINFC504_DMA_CTRL) &
+ HINFC504_DMA_CTRL_DMA_START)) {
+ cond_resched();
+ return 0;
+ }
+ }
+
+ dev_err(host->dev, "nand controller suspend timeout.\n");
+
+ return -EAGAIN;
+}
+
+static int hisi_nfc_resume(struct device *dev)
+{
+ int cs;
+ struct hinfc_host *host = dev_get_drvdata(dev);
+ struct nand_chip *chip = &host->chip;
+
+ for (cs = 0; cs < chip->numchips; cs++)
+ hisi_nfc_send_cmd_reset(host, cs);
+ hinfc_write(host, SET_HINFC504_PWIDTH(HINFC504_W_LATCH,
+ HINFC504_R_LATCH, HINFC504_RW_LATCH), HINFC504_PWIDTH);
+
+ return 0;
+}
+#endif
+static SIMPLE_DEV_PM_OPS(hisi_nfc_pm_ops, hisi_nfc_suspend, hisi_nfc_resume);
+
+static const struct of_device_id nfc_id_table[] = {
+ { .compatible = "hisilicon,504-nfc" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, nfc_id_table);
+
+static struct platform_driver hisi_nfc_driver = {
+ .driver = {
+ .name = "hisi_nand",
+ .of_match_table = nfc_id_table,
+ .pm = &hisi_nfc_pm_ops,
+ },
+ .probe = hisi_nfc_probe,
+ .remove = hisi_nfc_remove,
+};
+
+module_platform_driver(hisi_nfc_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Zhou Wang");
+MODULE_AUTHOR("Zhiyong Cai");
+MODULE_DESCRIPTION("Hisilicon Nand Flash Controller Driver");
diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/jz4740_nand.c
index 1633ec9..ebf2cce 100644
--- a/drivers/mtd/nand/jz4740_nand.c
+++ b/drivers/mtd/nand/jz4740_nand.c
@@ -69,7 +69,7 @@
int selected_bank;
- struct jz_nand_platform_data *pdata;
+ struct gpio_desc *busy_gpio;
bool is_reading;
};
@@ -131,7 +131,7 @@
static int jz_nand_dev_ready(struct mtd_info *mtd)
{
struct jz_nand *nand = mtd_to_jz_nand(mtd);
- return gpio_get_value_cansleep(nand->pdata->busy_gpio);
+ return gpiod_get_value_cansleep(nand->busy_gpio);
}
static void jz_nand_hwctl(struct mtd_info *mtd, int mode)
@@ -423,14 +423,12 @@
if (ret)
goto err_free;
- if (pdata && gpio_is_valid(pdata->busy_gpio)) {
- ret = gpio_request(pdata->busy_gpio, "NAND busy pin");
- if (ret) {
- dev_err(&pdev->dev,
- "Failed to request busy gpio %d: %d\n",
- pdata->busy_gpio, ret);
- goto err_iounmap_mmio;
- }
+ nand->busy_gpio = devm_gpiod_get_optional(&pdev->dev, "busy", GPIOD_IN);
+ if (IS_ERR(nand->busy_gpio)) {
+ ret = PTR_ERR(nand->busy_gpio);
+ dev_err(&pdev->dev, "Failed to request busy gpio %d\n",
+ ret);
+ goto err_iounmap_mmio;
}
mtd = &nand->mtd;
@@ -454,10 +452,9 @@
chip->cmd_ctrl = jz_nand_cmd_ctrl;
chip->select_chip = jz_nand_select_chip;
- if (pdata && gpio_is_valid(pdata->busy_gpio))
+ if (nand->busy_gpio)
chip->dev_ready = jz_nand_dev_ready;
- nand->pdata = pdata;
platform_set_drvdata(pdev, nand);
/* We are going to autodetect NAND chips in the banks specified in the
@@ -496,7 +493,7 @@
}
if (chipnr == 0) {
dev_err(&pdev->dev, "No NAND chips found\n");
- goto err_gpio_busy;
+ goto err_iounmap_mmio;
}
if (pdata && pdata->ident_callback) {
@@ -533,9 +530,6 @@
nand->bank_base[bank - 1]);
}
writel(0, nand->base + JZ_REG_NAND_CTRL);
-err_gpio_busy:
- if (pdata && gpio_is_valid(pdata->busy_gpio))
- gpio_free(pdata->busy_gpio);
err_iounmap_mmio:
jz_nand_iounmap_resource(nand->mem, nand->base);
err_free:
@@ -546,7 +540,6 @@
static int jz_nand_remove(struct platform_device *pdev)
{
struct jz_nand *nand = platform_get_drvdata(pdev);
- struct jz_nand_platform_data *pdata = dev_get_platdata(&pdev->dev);
size_t i;
nand_release(&nand->mtd);
@@ -562,8 +555,6 @@
gpio_free(JZ_GPIO_MEM_CS0 + bank - 1);
}
}
- if (pdata && gpio_is_valid(pdata->busy_gpio))
- gpio_free(pdata->busy_gpio);
jz_nand_iounmap_resource(nand->mem, nand->base);
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 41585df..df7eb4f 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -157,7 +157,6 @@
/**
* nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
- * nand_read_byte16 - [DEFAULT] read one byte endianness aware from the chip
* @mtd: MTD device structure
*
* Default read function for 16bit buswidth with endianness conversion.
@@ -1751,11 +1750,10 @@
static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
int page)
{
- uint8_t *buf = chip->oob_poi;
int length = mtd->oobsize;
int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad;
int eccsize = chip->ecc.size;
- uint8_t *bufpoi = buf;
+ uint8_t *bufpoi = chip->oob_poi;
int i, toread, sndrnd = 0, pos;
chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page);
@@ -2944,6 +2942,16 @@
__func__);
}
+/**
+ * nand_shutdown - [MTD Interface] Finish the current NAND operation and
+ * prevent further operations
+ * @mtd: MTD device structure
+ */
+static void nand_shutdown(struct mtd_info *mtd)
+{
+ nand_get_device(mtd, FL_SHUTDOWN);
+}
+
/* Set default functions */
static void nand_set_defaults(struct nand_chip *chip, int busw)
{
@@ -4028,22 +4036,24 @@
ecc->read_oob = nand_read_oob_std;
ecc->write_oob = nand_write_oob_std;
/*
- * Board driver should supply ecc.size and ecc.bytes values to
- * select how many bits are correctable; see nand_bch_init()
- * for details. Otherwise, default to 4 bits for large page
- * devices.
+ * Board driver should supply ecc.size and ecc.strength values
+ * to select how many bits are correctable. Otherwise, default
+ * to 4 bits for large page devices.
*/
if (!ecc->size && (mtd->oobsize >= 64)) {
ecc->size = 512;
- ecc->bytes = DIV_ROUND_UP(13 * ecc->strength, 8);
+ ecc->strength = 4;
}
+
+ /* See nand_bch_init() for details. */
+ ecc->bytes = DIV_ROUND_UP(
+ ecc->strength * fls(8 * ecc->size), 8);
ecc->priv = nand_bch_init(mtd, ecc->size, ecc->bytes,
&ecc->layout);
if (!ecc->priv) {
pr_warn("BCH ECC initialization failed!\n");
BUG();
}
- ecc->strength = ecc->bytes * 8 / fls(8 * ecc->size);
break;
case NAND_ECC_NONE:
@@ -4146,6 +4156,7 @@
mtd->_unlock = NULL;
mtd->_suspend = nand_suspend;
mtd->_resume = nand_resume;
+ mtd->_reboot = nand_shutdown;
mtd->_block_isreserved = nand_block_isreserved;
mtd->_block_isbad = nand_block_isbad;
mtd->_block_markbad = nand_block_markbad;
@@ -4161,7 +4172,7 @@
* properly set.
*/
if (!mtd->bitflip_threshold)
- mtd->bitflip_threshold = mtd->ecc_strength;
+ mtd->bitflip_threshold = DIV_ROUND_UP(mtd->ecc_strength * 3, 4);
/* Check, if we should skip the bad block table scan */
if (chip->options & NAND_SKIP_BBTSCAN)
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/nandsim.c
index ab5bbf5..f232427 100644
--- a/drivers/mtd/nand/nandsim.c
+++ b/drivers/mtd/nand/nandsim.c
@@ -245,7 +245,6 @@
#define STATE_DATAOUT 0x00001000 /* waiting for page data output */
#define STATE_DATAOUT_ID 0x00002000 /* waiting for ID bytes output */
#define STATE_DATAOUT_STATUS 0x00003000 /* waiting for status output */
-#define STATE_DATAOUT_STATUS_M 0x00004000 /* waiting for multi-plane status output */
#define STATE_DATAOUT_MASK 0x00007000 /* data output states mask */
/* Previous operation is done, ready to accept new requests */
@@ -269,7 +268,6 @@
#define OPT_ANY 0xFFFFFFFF /* any chip supports this operation */
#define OPT_PAGE512 0x00000002 /* 512-byte page chips */
#define OPT_PAGE2048 0x00000008 /* 2048-byte page chips */
-#define OPT_SMARTMEDIA 0x00000010 /* SmartMedia technology chips */
#define OPT_PAGE512_8BIT 0x00000040 /* 512-byte page chips with 8-bit bus width */
#define OPT_PAGE4096 0x00000080 /* 4096-byte page chips */
#define OPT_LARGEPAGE (OPT_PAGE2048 | OPT_PAGE4096) /* 2048 & 4096-byte page chips */
@@ -1096,8 +1094,6 @@
return "STATE_DATAOUT_ID";
case STATE_DATAOUT_STATUS:
return "STATE_DATAOUT_STATUS";
- case STATE_DATAOUT_STATUS_M:
- return "STATE_DATAOUT_STATUS_M";
case STATE_READY:
return "STATE_READY";
case STATE_UNKNOWN:
@@ -1865,7 +1861,6 @@
break;
case STATE_DATAOUT_STATUS:
- case STATE_DATAOUT_STATUS_M:
ns->regs.count = ns->regs.num = 0;
break;
@@ -2005,7 +2000,6 @@
}
if (NS_STATE(ns->state) == STATE_DATAOUT_STATUS
- || NS_STATE(ns->state) == STATE_DATAOUT_STATUS_M
|| NS_STATE(ns->state) == STATE_DATAOUT) {
int row = ns->regs.row;
@@ -2343,6 +2337,7 @@
}
chip->ecc.mode = NAND_ECC_SOFT_BCH;
chip->ecc.size = 512;
+ chip->ecc.strength = bch;
chip->ecc.bytes = eccbytes;
NS_INFO("using %u-bit/%u bytes BCH ECC\n", bch, chip->ecc.size);
}
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 63f858e..60fa899 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -1048,10 +1048,9 @@
* @mtd: MTD device structure
* @mode: Read/Write mode
*
- * When using BCH, sector size is hardcoded to 512 bytes.
- * Using wrapping mode 6 both for reading and writing if ELM module not uses
- * for error correction.
- * On writing,
+ * When using BCH with SW correction (i.e. no ELM), sector size is set
+ * to 512 bytes and we use BCH_WRAPMODE_6 wrapping mode
+ * for both reading and writing with:
* eccsize0 = 0 (no additional protected byte in spare area)
* eccsize1 = 32 (skip 32 nibbles = 16 bytes per sector in spare area)
*/
@@ -1071,15 +1070,9 @@
case OMAP_ECC_BCH4_CODE_HW_DETECTION_SW:
bch_type = 0;
nsectors = 1;
- if (mode == NAND_ECC_READ) {
- wr_mode = BCH_WRAPMODE_6;
- ecc_size0 = BCH_ECC_SIZE0;
- ecc_size1 = BCH_ECC_SIZE1;
- } else {
- wr_mode = BCH_WRAPMODE_6;
- ecc_size0 = BCH_ECC_SIZE0;
- ecc_size1 = BCH_ECC_SIZE1;
- }
+ wr_mode = BCH_WRAPMODE_6;
+ ecc_size0 = BCH_ECC_SIZE0;
+ ecc_size1 = BCH_ECC_SIZE1;
break;
case OMAP_ECC_BCH4_CODE_HW:
bch_type = 0;
@@ -1097,15 +1090,9 @@
case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
bch_type = 1;
nsectors = 1;
- if (mode == NAND_ECC_READ) {
- wr_mode = BCH_WRAPMODE_6;
- ecc_size0 = BCH_ECC_SIZE0;
- ecc_size1 = BCH_ECC_SIZE1;
- } else {
- wr_mode = BCH_WRAPMODE_6;
- ecc_size0 = BCH_ECC_SIZE0;
- ecc_size1 = BCH_ECC_SIZE1;
- }
+ wr_mode = BCH_WRAPMODE_6;
+ ecc_size0 = BCH_ECC_SIZE0;
+ ecc_size1 = BCH_ECC_SIZE1;
break;
case OMAP_ECC_BCH8_CODE_HW:
bch_type = 1;
diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/sunxi_nand.c
index ccaa8e2..6f93b29 100644
--- a/drivers/mtd/nand/sunxi_nand.c
+++ b/drivers/mtd/nand/sunxi_nand.c
@@ -1110,8 +1110,6 @@
switch (ecc->mode) {
case NAND_ECC_SOFT_BCH:
- ecc->bytes = DIV_ROUND_UP(ecc->strength * fls(8 * ecc->size),
- 8);
break;
case NAND_ECC_HW:
ret = sunxi_nand_hw_ecc_ctrl_init(mtd, ecc, np);
diff --git a/drivers/mtd/nftlmount.c b/drivers/mtd/nftlmount.c
index 51b9d6a..a5dfbfb 100644
--- a/drivers/mtd/nftlmount.c
+++ b/drivers/mtd/nftlmount.c
@@ -89,9 +89,10 @@
}
/* To be safer with BIOS, also use erase mark as discriminant */
- if ((ret = nftl_read_oob(mtd, block * nftl->EraseSize +
+ ret = nftl_read_oob(mtd, block * nftl->EraseSize +
SECTORSIZE + 8, 8, &retlen,
- (char *)&h1) < 0)) {
+ (char *)&h1);
+ if (ret < 0) {
printk(KERN_WARNING "ANAND header found at 0x%x in mtd%d, but OOB data read failed (err %d)\n",
block * nftl->EraseSize, nftl->mbd.mtd->index, ret);
continue;
@@ -109,8 +110,9 @@
}
/* Finally reread to check ECC */
- if ((ret = mtd->read(mtd, block * nftl->EraseSize, SECTORSIZE,
- &retlen, buf) < 0)) {
+ ret = mtd->read(mtd, block * nftl->EraseSize, SECTORSIZE,
+ &retlen, buf);
+ if (ret < 0) {
printk(KERN_NOTICE "ANAND header found at 0x%x in mtd%d, but ECC read failed (err %d)\n",
block * nftl->EraseSize, nftl->mbd.mtd->index, ret);
continue;
@@ -228,9 +230,11 @@
The new DiskOnChip driver already scanned the bad block table. Just query it.
if ((i & (SECTORSIZE - 1)) == 0) {
/* read one sector for every SECTORSIZE of blocks */
- if ((ret = mtd->read(nftl->mbd.mtd, block * nftl->EraseSize +
- i + SECTORSIZE, SECTORSIZE, &retlen,
- buf)) < 0) {
+ ret = mtd->read(nftl->mbd.mtd,
+ block * nftl->EraseSize + i +
+ SECTORSIZE, SECTORSIZE,
+ &retlen, buf);
+ if (ret < 0) {
printk(KERN_NOTICE "Read of bad sector table failed (err %d)\n",
ret);
kfree(nftl->ReplUnitTable);
diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index 39763b9..1c7308c 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -57,7 +57,9 @@
#define QUADSPI_BUF3CR 0x1c
#define QUADSPI_BUF3CR_ALLMST_SHIFT 31
-#define QUADSPI_BUF3CR_ALLMST (1 << QUADSPI_BUF3CR_ALLMST_SHIFT)
+#define QUADSPI_BUF3CR_ALLMST_MASK (1 << QUADSPI_BUF3CR_ALLMST_SHIFT)
+#define QUADSPI_BUF3CR_ADATSZ_SHIFT 8
+#define QUADSPI_BUF3CR_ADATSZ_MASK (0xFF << QUADSPI_BUF3CR_ADATSZ_SHIFT)
#define QUADSPI_BFGENCR 0x20
#define QUADSPI_BFGENCR_PAR_EN_SHIFT 16
@@ -198,18 +200,21 @@
enum fsl_qspi_devtype devtype;
int rxfifo;
int txfifo;
+ int ahb_buf_size;
};
static struct fsl_qspi_devtype_data vybrid_data = {
.devtype = FSL_QUADSPI_VYBRID,
.rxfifo = 128,
- .txfifo = 64
+ .txfifo = 64,
+ .ahb_buf_size = 1024
};
static struct fsl_qspi_devtype_data imx6sx_data = {
.devtype = FSL_QUADSPI_IMX6SX,
.rxfifo = 128,
- .txfifo = 512
+ .txfifo = 512,
+ .ahb_buf_size = 1024
};
#define FSL_QSPI_MAX_CHIP 4
@@ -227,6 +232,7 @@
u32 nor_num;
u32 clk_rate;
unsigned int chip_base_addr; /* We may support two chips. */
+ bool has_second_chip;
};
static inline int is_vybrid_qspi(struct fsl_qspi *q)
@@ -583,7 +589,12 @@
writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF0CR);
writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF1CR);
writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF2CR);
- writel(QUADSPI_BUF3CR_ALLMST, base + QUADSPI_BUF3CR);
+ /*
+ * Set ADATSZ with the maximum AHB buffer size to improve the
+ * read performance.
+ */
+ writel(QUADSPI_BUF3CR_ALLMST_MASK | ((q->devtype_data->ahb_buf_size / 8)
+ << QUADSPI_BUF3CR_ADATSZ_SHIFT), base + QUADSPI_BUF3CR);
/* We only use the buffer3 */
writel(0, base + QUADSPI_BUF0IND);
@@ -783,7 +794,6 @@
struct spi_nor *nor;
struct mtd_info *mtd;
int ret, i = 0;
- bool has_second_chip = false;
const struct of_device_id *of_id =
of_match_device(fsl_qspi_dt_ids, &pdev->dev);
@@ -798,37 +808,30 @@
/* find the resources */
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
q->iobase = devm_ioremap_resource(dev, res);
- if (IS_ERR(q->iobase)) {
- ret = PTR_ERR(q->iobase);
- goto map_failed;
- }
+ if (IS_ERR(q->iobase))
+ return PTR_ERR(q->iobase);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
"QuadSPI-memory");
q->ahb_base = devm_ioremap_resource(dev, res);
- if (IS_ERR(q->ahb_base)) {
- ret = PTR_ERR(q->ahb_base);
- goto map_failed;
- }
+ if (IS_ERR(q->ahb_base))
+ return PTR_ERR(q->ahb_base);
+
q->memmap_phy = res->start;
/* find the clocks */
q->clk_en = devm_clk_get(dev, "qspi_en");
- if (IS_ERR(q->clk_en)) {
- ret = PTR_ERR(q->clk_en);
- goto map_failed;
- }
+ if (IS_ERR(q->clk_en))
+ return PTR_ERR(q->clk_en);
q->clk = devm_clk_get(dev, "qspi");
- if (IS_ERR(q->clk)) {
- ret = PTR_ERR(q->clk);
- goto map_failed;
- }
+ if (IS_ERR(q->clk))
+ return PTR_ERR(q->clk);
ret = clk_prepare_enable(q->clk_en);
if (ret) {
dev_err(dev, "can not enable the qspi_en clock\n");
- goto map_failed;
+ return ret;
}
ret = clk_prepare_enable(q->clk);
@@ -860,14 +863,14 @@
goto irq_failed;
if (of_get_property(np, "fsl,qspi-has-second-chip", NULL))
- has_second_chip = true;
+ q->has_second_chip = true;
/* iterate the subnodes. */
for_each_available_child_of_node(dev->of_node, np) {
char modalias[40];
/* skip the holes */
- if (!has_second_chip)
+ if (!q->has_second_chip)
i *= 2;
nor = &q->nor[i];
@@ -890,24 +893,24 @@
ret = of_modalias_node(np, modalias, sizeof(modalias));
if (ret < 0)
- goto map_failed;
+ goto irq_failed;
ret = of_property_read_u32(np, "spi-max-frequency",
&q->clk_rate);
if (ret < 0)
- goto map_failed;
+ goto irq_failed;
/* set the chip address for READID */
fsl_qspi_set_base_addr(q, nor);
ret = spi_nor_scan(nor, modalias, SPI_NOR_QUAD);
if (ret)
- goto map_failed;
+ goto irq_failed;
ppdata.of_node = np;
ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0);
if (ret)
- goto map_failed;
+ goto irq_failed;
/* Set the correct NOR size now. */
if (q->nor_size == 0) {
@@ -939,19 +942,19 @@
clk_disable(q->clk);
clk_disable(q->clk_en);
- dev_info(dev, "QuadSPI SPI NOR flash driver\n");
return 0;
last_init_failed:
- for (i = 0; i < q->nor_num; i++)
+ for (i = 0; i < q->nor_num; i++) {
+ /* skip the holes */
+ if (!q->has_second_chip)
+ i *= 2;
mtd_device_unregister(&q->mtd[i]);
-
+ }
irq_failed:
clk_disable_unprepare(q->clk);
clk_failed:
clk_disable_unprepare(q->clk_en);
-map_failed:
- dev_err(dev, "Freescale QuadSPI probe failed\n");
return ret;
}
@@ -960,8 +963,12 @@
struct fsl_qspi *q = platform_get_drvdata(pdev);
int i;
- for (i = 0; i < q->nor_num; i++)
+ for (i = 0; i < q->nor_num; i++) {
+ /* skip the holes */
+ if (!q->has_second_chip)
+ i *= 2;
mtd_device_unregister(&q->mtd[i]);
+ }
/* disable the hardware */
writel(QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
@@ -972,6 +979,22 @@
return 0;
}
+static int fsl_qspi_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ return 0;
+}
+
+static int fsl_qspi_resume(struct platform_device *pdev)
+{
+ struct fsl_qspi *q = platform_get_drvdata(pdev);
+
+ fsl_qspi_nor_setup(q);
+ fsl_qspi_set_map_addr(q);
+ fsl_qspi_nor_setup_last(q);
+
+ return 0;
+}
+
static struct platform_driver fsl_qspi_driver = {
.driver = {
.name = "fsl-quadspi",
@@ -980,6 +1003,8 @@
},
.probe = fsl_qspi_probe,
.remove = fsl_qspi_remove,
+ .suspend = fsl_qspi_suspend,
+ .resume = fsl_qspi_resume,
};
module_platform_driver(fsl_qspi_driver);
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 0f8ec3c..b6a5a0c 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -538,6 +538,7 @@
/* GigaDevice */
{ "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64, SECT_4K) },
{ "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128, SECT_4K) },
+ { "gd25q128", INFO(0xc84018, 0, 64 * 1024, 256, SECT_4K) },
/* Intel/Numonyx -- xxxs33b */
{ "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) },
@@ -560,14 +561,14 @@
{ "mx66l1g55g", INFO(0xc2261b, 0, 64 * 1024, 2048, SPI_NOR_QUAD_READ) },
/* Micron */
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
- { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) },
- { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, USE_FSR) },
- { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, USE_FSR) },
+ { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SPI_NOR_QUAD_READ) },
+ { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SPI_NOR_QUAD_READ) },
+ { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SPI_NOR_QUAD_READ) },
+ { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
/* PMC */
{ "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) },
@@ -891,6 +892,45 @@
return 0;
}
+static int micron_quad_enable(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RD_EVCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading EVCR\n", ret);
+ return ret;
+ }
+
+ write_enable(nor);
+
+ /* set EVCR, enable quad I/O */
+ nor->cmd_buf[0] = val & ~EVCR_QUAD_EN_MICRON;
+ ret = nor->write_reg(nor, SPINOR_OP_WD_EVCR, nor->cmd_buf, 1, 0);
+ if (ret < 0) {
+ dev_err(nor->dev, "error while writing EVCR register\n");
+ return ret;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ /* read EVCR and check it */
+ ret = nor->read_reg(nor, SPINOR_OP_RD_EVCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading EVCR\n", ret);
+ return ret;
+ }
+ if (val & EVCR_QUAD_EN_MICRON) {
+ dev_err(nor->dev, "Micron EVCR Quad bit not clear\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
static int set_quad_mode(struct spi_nor *nor, struct flash_info *info)
{
int status;
@@ -903,6 +943,13 @@
return -EINVAL;
}
return status;
+ case CFI_MFR_ST:
+ status = micron_quad_enable(nor);
+ if (status) {
+ dev_err(nor->dev, "Micron quad-read not enabled\n");
+ return -EINVAL;
+ }
+ return status;
default:
status = spansion_quad_enable(nor);
if (status) {
diff --git a/fs/jffs2/compr_rubin.c b/fs/jffs2/compr_rubin.c
index 92e0644b..556de10 100644
--- a/fs/jffs2/compr_rubin.c
+++ b/fs/jffs2/compr_rubin.c
@@ -84,11 +84,6 @@
return bit;
}
-static inline int pulledbits(struct pushpull *pp)
-{
- return pp->ofs;
-}
-
static void init_rubin(struct rubin_state *rs, int div, int *bits)
{
diff --git a/include/linux/mtd/mtd.h b/include/linux/mtd/mtd.h
index 031ff3a..c06f537 100644
--- a/include/linux/mtd/mtd.h
+++ b/include/linux/mtd/mtd.h
@@ -227,6 +227,7 @@
int (*_block_markbad) (struct mtd_info *mtd, loff_t ofs);
int (*_suspend) (struct mtd_info *mtd);
void (*_resume) (struct mtd_info *mtd);
+ void (*_reboot) (struct mtd_info *mtd);
/*
* If the driver is something smart, like UBI, it may need to maintain
* its own reference counting. The below functions are only for driver.
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 63aeccf..4720b86 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -56,6 +56,10 @@
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+/* Used for Micron flashes only. */
+#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
+#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */
+
/* Status Register bits. */
#define SR_WIP 1 /* Write in progress */
#define SR_WEL 2 /* Write enable latch */
@@ -67,6 +71,9 @@
#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */
+/* Enhanced Volatile Configuration Register bits */
+#define EVCR_QUAD_EN_MICRON 0x80 /* Micron Quad I/O */
+
/* Flag Status Register bits */
#define FSR_READY 0x80
