gpio/omap: maintain GPIO and IRQ usage separately
The GPIO OMAP controller pins can be used as IRQ and GPIO
independently so is necessary to keep track GPIO pins and
IRQ lines usage separately to make sure that the bank will
always be enabled while being used.
Also move gpio_is_input() definition in preparation for the
next patch that setups the controller's irq_chip driver when
a caller requests an interrupt line.
Cc: stable@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: George Cherian <george.cherian@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index 0ff4355..a4fe038 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -63,6 +63,7 @@
struct gpio_chip chip;
struct clk *dbck;
u32 mod_usage;
+ u32 irq_usage;
u32 dbck_enable_mask;
bool dbck_enabled;
struct device *dev;
@@ -86,6 +87,9 @@
#define GPIO_BIT(bank, gpio) (1 << GPIO_INDEX(bank, gpio))
#define GPIO_MOD_CTRL_BIT BIT(0)
+#define BANK_USED(bank) (bank->mod_usage || bank->irq_usage)
+#define LINE_USED(line, offset) (line & (1 << offset))
+
static int irq_to_gpio(struct gpio_bank *bank, unsigned int gpio_irq)
{
return bank->chip.base + gpio_irq;
@@ -420,6 +424,13 @@
return 0;
}
+static int gpio_is_input(struct gpio_bank *bank, int mask)
+{
+ void __iomem *reg = bank->base + bank->regs->direction;
+
+ return __raw_readl(reg) & mask;
+}
+
static int gpio_irq_type(struct irq_data *d, unsigned type)
{
struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
@@ -427,7 +438,7 @@
int retval;
unsigned long flags;
- if (WARN_ON(!bank->mod_usage))
+ if (WARN_ON(!BANK_USED(bank)))
return -EINVAL;
#ifdef CONFIG_ARCH_OMAP1
@@ -447,6 +458,7 @@
spin_lock_irqsave(&bank->lock, flags);
retval = _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), type);
+ bank->irq_usage |= 1 << GPIO_INDEX(bank, gpio);
spin_unlock_irqrestore(&bank->lock, flags);
if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
@@ -603,7 +615,7 @@
* If this is the first gpio_request for the bank,
* enable the bank module.
*/
- if (!bank->mod_usage)
+ if (!BANK_USED(bank))
pm_runtime_get_sync(bank->dev);
spin_lock_irqsave(&bank->lock, flags);
@@ -619,7 +631,7 @@
__raw_writel(__raw_readl(reg) | (1 << offset), reg);
}
- if (bank->regs->ctrl && !bank->mod_usage) {
+ if (bank->regs->ctrl && !BANK_USED(bank)) {
void __iomem *reg = bank->base + bank->regs->ctrl;
u32 ctrl;
@@ -654,7 +666,7 @@
bank->mod_usage &= ~(1 << offset);
- if (bank->regs->ctrl && !bank->mod_usage) {
+ if (bank->regs->ctrl && !BANK_USED(bank)) {
void __iomem *reg = bank->base + bank->regs->ctrl;
u32 ctrl;
@@ -672,7 +684,7 @@
* If this is the last gpio to be freed in the bank,
* disable the bank module.
*/
- if (!bank->mod_usage)
+ if (!BANK_USED(bank))
pm_runtime_put(bank->dev);
}
@@ -762,8 +774,10 @@
struct gpio_bank *bank = irq_data_get_irq_chip_data(d);
unsigned int gpio = irq_to_gpio(bank, d->hwirq);
unsigned long flags;
+ unsigned offset = GPIO_INDEX(bank, gpio);
spin_lock_irqsave(&bank->lock, flags);
+ bank->irq_usage &= ~(1 << offset);
_reset_gpio(bank, gpio);
spin_unlock_irqrestore(&bank->lock, flags);
}
@@ -897,13 +911,6 @@
return 0;
}
-static int gpio_is_input(struct gpio_bank *bank, int mask)
-{
- void __iomem *reg = bank->base + bank->regs->direction;
-
- return __raw_readl(reg) & mask;
-}
-
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank;
@@ -1400,7 +1407,7 @@
struct gpio_bank *bank;
list_for_each_entry(bank, &omap_gpio_list, node) {
- if (!bank->mod_usage || !bank->loses_context)
+ if (!BANK_USED(bank) || !bank->loses_context)
continue;
bank->power_mode = pwr_mode;
@@ -1414,7 +1421,7 @@
struct gpio_bank *bank;
list_for_each_entry(bank, &omap_gpio_list, node) {
- if (!bank->mod_usage || !bank->loses_context)
+ if (!BANK_USED(bank) || !bank->loses_context)
continue;
pm_runtime_get_sync(bank->dev);
