/*
 *
 * This file is provided under a dual BSD/GPLv2 license.  When using or
 * redistributing this file, you may do so under either license.
 *
 * GPL LICENSE SUMMARY
 *
 * Copyright(c) 2015 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * BSD LICENSE
 *
 * Copyright(c) 2015 Intel Corporation.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 *  - Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *  - Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in
 *    the documentation and/or other materials provided with the
 *    distribution.
 *  - Neither the name of Intel Corporation nor the names of its
 *    contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 */

#include <linux/pci.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/vmalloc.h>
#include <linux/aer.h>
#include <linux/module.h>

#include "hfi.h"
#include "chip_registers.h"

/* link speed vector for Gen3 speed - not in Linux headers */
#define GEN1_SPEED_VECTOR 0x1
#define GEN2_SPEED_VECTOR 0x2
#define GEN3_SPEED_VECTOR 0x3

/*
 * This file contains PCIe utility routines.
 */

/*
 * Code to adjust PCIe capabilities.
 */
static void tune_pcie_caps(struct hfi1_devdata *);

/*
 * Do all the common PCIe setup and initialization.
 * devdata is not yet allocated, and is not allocated until after this
 * routine returns success.  Therefore dd_dev_err() can't be used for error
 * printing.
 */
int hfi1_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent)
{
	int ret;

	ret = pci_enable_device(pdev);
	if (ret) {
		/*
		 * This can happen (in theory) iff:
		 * We did a chip reset, and then failed to reprogram the
		 * BAR, or the chip reset due to an internal error.  We then
		 * unloaded the driver and reloaded it.
		 *
		 * Both reset cases set the BAR back to initial state.  For
		 * the latter case, the AER sticky error bit at offset 0x718
		 * should be set, but the Linux kernel doesn't yet know
		 * about that, it appears.  If the original BAR was retained
		 * in the kernel data structures, this may be OK.
		 */
		hfi1_early_err(&pdev->dev, "pci enable failed: error %d\n",
			       -ret);
		goto done;
	}

	ret = pci_request_regions(pdev, DRIVER_NAME);
	if (ret) {
		hfi1_early_err(&pdev->dev,
			       "pci_request_regions fails: err %d\n", -ret);
		goto bail;
	}

	ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
	if (ret) {
		/*
		 * If the 64 bit setup fails, try 32 bit.  Some systems
		 * do not setup 64 bit maps on systems with 2GB or less
		 * memory installed.
		 */
		ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
		if (ret) {
			hfi1_early_err(&pdev->dev,
				       "Unable to set DMA mask: %d\n", ret);
			goto bail;
		}
		ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
	} else
		ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
	if (ret) {
		hfi1_early_err(&pdev->dev,
			       "Unable to set DMA consistent mask: %d\n", ret);
		goto bail;
	}

	pci_set_master(pdev);
	ret = pci_enable_pcie_error_reporting(pdev);
	if (ret) {
		hfi1_early_err(&pdev->dev,
			       "Unable to enable pcie error reporting: %d\n",
			      ret);
		ret = 0;
	}
	goto done;

bail:
	hfi1_pcie_cleanup(pdev);
done:
	return ret;
}

/*
 * Clean what was done in hfi1_pcie_init()
 */
void hfi1_pcie_cleanup(struct pci_dev *pdev)
{
	pci_disable_device(pdev);
	/*
	 * Release regions should be called after the disable. OK to
	 * call if request regions has not been called or failed.
	 */
	pci_release_regions(pdev);
}

/*
 * Do remaining PCIe setup, once dd is allocated, and save away
 * fields required to re-initialize after a chip reset, or for
 * various other purposes
 */
int hfi1_pcie_ddinit(struct hfi1_devdata *dd, struct pci_dev *pdev,
		     const struct pci_device_id *ent)
{
	unsigned long len;
	resource_size_t addr;

	dd->pcidev = pdev;
	pci_set_drvdata(pdev, dd);

	addr = pci_resource_start(pdev, 0);
	len = pci_resource_len(pdev, 0);

	/*
	 * The TXE PIO buffers are at the tail end of the chip space.
	 * Cut them off and map them separately.
	 */

	/* sanity check vs expectations */
	if (len != TXE_PIO_SEND + TXE_PIO_SIZE) {
		dd_dev_err(dd, "chip PIO range does not match\n");
		return -EINVAL;
	}

	dd->kregbase = ioremap_nocache(addr, TXE_PIO_SEND);
	if (!dd->kregbase)
		return -ENOMEM;

	dd->piobase = ioremap_wc(addr + TXE_PIO_SEND, TXE_PIO_SIZE);
	if (!dd->piobase) {
		iounmap(dd->kregbase);
		return -ENOMEM;
	}

	dd->flags |= HFI1_PRESENT;	/* now register routines work */

	dd->kregend = dd->kregbase + TXE_PIO_SEND;
	dd->physaddr = addr;        /* used for io_remap, etc. */

	/*
	 * Re-map the chip's RcvArray as write-combining to allow us
	 * to write an entire cacheline worth of entries in one shot.
	 * If this re-map fails, just continue - the RcvArray programming
	 * function will handle both cases.
	 */
	dd->chip_rcv_array_count = read_csr(dd, RCV_ARRAY_CNT);
	dd->rcvarray_wc = ioremap_wc(addr + RCV_ARRAY,
				     dd->chip_rcv_array_count * 8);
	dd_dev_info(dd, "WC Remapped RcvArray: %p\n", dd->rcvarray_wc);
	/*
	 * Save BARs and command to rewrite after device reset.
	 */
	dd->pcibar0 = addr;
	dd->pcibar1 = addr >> 32;
	pci_read_config_dword(dd->pcidev, PCI_ROM_ADDRESS, &dd->pci_rom);
	pci_read_config_word(dd->pcidev, PCI_COMMAND, &dd->pci_command);
	pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL, &dd->pcie_devctl);
	pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL, &dd->pcie_lnkctl);
	pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVCTL2,
							&dd->pcie_devctl2);
	pci_read_config_dword(dd->pcidev, PCI_CFG_MSIX0, &dd->pci_msix0);
	pci_read_config_dword(dd->pcidev, PCIE_CFG_SPCIE1,
							&dd->pci_lnkctl3);
	pci_read_config_dword(dd->pcidev, PCIE_CFG_TPH2, &dd->pci_tph2);

	return 0;
}

/*
 * Do PCIe cleanup related to dd, after chip-specific cleanup, etc.  Just prior
 * to releasing the dd memory.
 * Void because all of the core pcie cleanup functions are void.
 */
void hfi1_pcie_ddcleanup(struct hfi1_devdata *dd)
{
	u64 __iomem *base = (void __iomem *) dd->kregbase;

	dd->flags &= ~HFI1_PRESENT;
	dd->kregbase = NULL;
	iounmap(base);
	if (dd->rcvarray_wc)
		iounmap(dd->rcvarray_wc);
	if (dd->piobase)
		iounmap(dd->piobase);

	pci_set_drvdata(dd->pcidev, NULL);
}

/*
 * Do a Function Level Reset (FLR) on the device.
 * Based on static function drivers/pci/pci.c:pcie_flr().
 */
void hfi1_pcie_flr(struct hfi1_devdata *dd)
{
	int i;
	u16 status;

	/* no need to check for the capability - we know the device has it */

	/* wait for Transaction Pending bit to clear, at most a few ms */
	for (i = 0; i < 4; i++) {
		if (i)
			msleep((1 << (i - 1)) * 100);

		pcie_capability_read_word(dd->pcidev, PCI_EXP_DEVSTA, &status);
		if (!(status & PCI_EXP_DEVSTA_TRPND))
			goto clear;
	}

	dd_dev_err(dd, "Transaction Pending bit is not clearing, proceeding with reset anyway\n");

clear:
	pcie_capability_set_word(dd->pcidev, PCI_EXP_DEVCTL,
						PCI_EXP_DEVCTL_BCR_FLR);
	/* PCIe spec requires the function to be back within 100ms */
	msleep(100);
}

static void msix_setup(struct hfi1_devdata *dd, int pos, u32 *msixcnt,
		       struct hfi1_msix_entry *hfi1_msix_entry)
{
	int ret;
	int nvec = *msixcnt;
	struct msix_entry *msix_entry;
	int i;

	/* We can't pass hfi1_msix_entry array to msix_setup
	 * so use a dummy msix_entry array and copy the allocated
	 * irq back to the hfi1_msix_entry array. */
	msix_entry = kmalloc_array(nvec, sizeof(*msix_entry), GFP_KERNEL);
	if (!msix_entry) {
		ret = -ENOMEM;
		goto do_intx;
	}

	for (i = 0; i < nvec; i++)
		msix_entry[i] = hfi1_msix_entry[i].msix;

	ret = pci_enable_msix_range(dd->pcidev, msix_entry, 1, nvec);
	if (ret < 0)
		goto free_msix_entry;
	nvec = ret;

	for (i = 0; i < nvec; i++)
		hfi1_msix_entry[i].msix = msix_entry[i];

	kfree(msix_entry);
	*msixcnt = nvec;
	return;

free_msix_entry:
	kfree(msix_entry);

do_intx:
	dd_dev_err(dd, "pci_enable_msix_range %d vectors failed: %d, falling back to INTx\n",
		   nvec, ret);
	*msixcnt = 0;
	hfi1_enable_intx(dd->pcidev);

}

/* return the PCIe link speed from the given link status */
static u32 extract_speed(u16 linkstat)
{
	u32 speed;

	switch (linkstat & PCI_EXP_LNKSTA_CLS) {
	default: /* not defined, assume Gen1 */
	case PCI_EXP_LNKSTA_CLS_2_5GB:
		speed = 2500; /* Gen 1, 2.5GHz */
		break;
	case PCI_EXP_LNKSTA_CLS_5_0GB:
		speed = 5000; /* Gen 2, 5GHz */
		break;
	case GEN3_SPEED_VECTOR:
		speed = 8000; /* Gen 3, 8GHz */
		break;
	}
	return speed;
}

/* return the PCIe link speed from the given link status */
static u32 extract_width(u16 linkstat)
{
	return (linkstat & PCI_EXP_LNKSTA_NLW) >> PCI_EXP_LNKSTA_NLW_SHIFT;
}

/* read the link status and set dd->{lbus_width,lbus_speed,lbus_info} */
static void update_lbus_info(struct hfi1_devdata *dd)
{
	u16 linkstat;

	pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKSTA, &linkstat);
	dd->lbus_width = extract_width(linkstat);
	dd->lbus_speed = extract_speed(linkstat);
	snprintf(dd->lbus_info, sizeof(dd->lbus_info),
		 "PCIe,%uMHz,x%u", dd->lbus_speed, dd->lbus_width);
}

/*
 * Read in the current PCIe link width and speed.  Find if the link is
 * Gen3 capable.
 */
int pcie_speeds(struct hfi1_devdata *dd)
{
	u32 linkcap;

	if (!pci_is_pcie(dd->pcidev)) {
		dd_dev_err(dd, "Can't find PCI Express capability!\n");
		return -EINVAL;
	}

	/* find if our max speed is Gen3 and parent supports Gen3 speeds */
	dd->link_gen3_capable = 1;

	pcie_capability_read_dword(dd->pcidev, PCI_EXP_LNKCAP, &linkcap);
	if ((linkcap & PCI_EXP_LNKCAP_SLS) != GEN3_SPEED_VECTOR) {
		dd_dev_info(dd,
			"This HFI is not Gen3 capable, max speed 0x%x, need 0x3\n",
			linkcap & PCI_EXP_LNKCAP_SLS);
		dd->link_gen3_capable = 0;
	}

	/*
	 * bus->max_bus_speed is set from the bridge's linkcap Max Link Speed
	 */
	if (dd->pcidev->bus->max_bus_speed != PCIE_SPEED_8_0GT) {
		dd_dev_info(dd, "Parent PCIe bridge does not support Gen3\n");
		dd->link_gen3_capable = 0;
	}

	/* obtain the link width and current speed */
	update_lbus_info(dd);

	/* check against expected pcie width and complain if "wrong" */
	if (dd->lbus_width < 16)
		dd_dev_err(dd, "PCIe width %u (x16 HFI)\n", dd->lbus_width);

	return 0;
}

/*
 * Returns in *nent:
 *	- actual number of interrupts allocated
 *	- 0 if fell back to INTx.
 */
void request_msix(struct hfi1_devdata *dd, u32 *nent,
		  struct hfi1_msix_entry *entry)
{
	int pos;

	pos = dd->pcidev->msix_cap;
	if (*nent && pos) {
		msix_setup(dd, pos, nent, entry);
		/* did it, either MSI-X or INTx */
	} else {
		*nent = 0;
		hfi1_enable_intx(dd->pcidev);
	}

	tune_pcie_caps(dd);
}

/*
 * Disable MSI-X.
 */
void hfi1_nomsix(struct hfi1_devdata *dd)
{
	pci_disable_msix(dd->pcidev);
}

void hfi1_enable_intx(struct pci_dev *pdev)
{
	/* first, turn on INTx */
	pci_intx(pdev, 1);
	/* then turn off MSI-X */
	pci_disable_msix(pdev);
}

/* restore command and BARs after a reset has wiped them out */
void restore_pci_variables(struct hfi1_devdata *dd)
{
	pci_write_config_word(dd->pcidev, PCI_COMMAND, dd->pci_command);
	pci_write_config_dword(dd->pcidev,
				PCI_BASE_ADDRESS_0, dd->pcibar0);
	pci_write_config_dword(dd->pcidev,
				PCI_BASE_ADDRESS_1, dd->pcibar1);
	pci_write_config_dword(dd->pcidev,
				PCI_ROM_ADDRESS, dd->pci_rom);
	pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL, dd->pcie_devctl);
	pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL, dd->pcie_lnkctl);
	pcie_capability_write_word(dd->pcidev, PCI_EXP_DEVCTL2,
							dd->pcie_devctl2);
	pci_write_config_dword(dd->pcidev, PCI_CFG_MSIX0, dd->pci_msix0);
	pci_write_config_dword(dd->pcidev, PCIE_CFG_SPCIE1,
							dd->pci_lnkctl3);
	pci_write_config_dword(dd->pcidev, PCIE_CFG_TPH2, dd->pci_tph2);
}


/*
 * BIOS may not set PCIe bus-utilization parameters for best performance.
 * Check and optionally adjust them to maximize our throughput.
 */
static int hfi1_pcie_caps;
module_param_named(pcie_caps, hfi1_pcie_caps, int, S_IRUGO);
MODULE_PARM_DESC(pcie_caps, "Max PCIe tuning: Payload (0..3), ReadReq (4..7)");

static void tune_pcie_caps(struct hfi1_devdata *dd)
{
	struct pci_dev *parent;
	u16 rc_mpss, rc_mps, ep_mpss, ep_mps;
	u16 rc_mrrs, ep_mrrs, max_mrrs;

	/* Find out supported and configured values for parent (root) */
	parent = dd->pcidev->bus->self;
	if (!pci_is_root_bus(parent->bus)) {
		dd_dev_info(dd, "Parent not root\n");
		return;
	}

	if (!pci_is_pcie(parent) || !pci_is_pcie(dd->pcidev))
		return;
	rc_mpss = parent->pcie_mpss;
	rc_mps = ffs(pcie_get_mps(parent)) - 8;
	/* Find out supported and configured values for endpoint (us) */
	ep_mpss = dd->pcidev->pcie_mpss;
	ep_mps = ffs(pcie_get_mps(dd->pcidev)) - 8;

	/* Find max payload supported by root, endpoint */
	if (rc_mpss > ep_mpss)
		rc_mpss = ep_mpss;

	/* If Supported greater than limit in module param, limit it */
	if (rc_mpss > (hfi1_pcie_caps & 7))
		rc_mpss = hfi1_pcie_caps & 7;
	/* If less than (allowed, supported), bump root payload */
	if (rc_mpss > rc_mps) {
		rc_mps = rc_mpss;
		pcie_set_mps(parent, 128 << rc_mps);
	}
	/* If less than (allowed, supported), bump endpoint payload */
	if (rc_mpss > ep_mps) {
		ep_mps = rc_mpss;
		pcie_set_mps(dd->pcidev, 128 << ep_mps);
	}

	/*
	 * Now the Read Request size.
	 * No field for max supported, but PCIe spec limits it to 4096,
	 * which is code '5' (log2(4096) - 7)
	 */
	max_mrrs = 5;
	if (max_mrrs > ((hfi1_pcie_caps >> 4) & 7))
		max_mrrs = (hfi1_pcie_caps >> 4) & 7;

	max_mrrs = 128 << max_mrrs;
	rc_mrrs = pcie_get_readrq(parent);
	ep_mrrs = pcie_get_readrq(dd->pcidev);

	if (max_mrrs > rc_mrrs) {
		rc_mrrs = max_mrrs;
		pcie_set_readrq(parent, rc_mrrs);
	}
	if (max_mrrs > ep_mrrs) {
		ep_mrrs = max_mrrs;
		pcie_set_readrq(dd->pcidev, ep_mrrs);
	}
}
/* End of PCIe capability tuning */

/*
 * From here through hfi1_pci_err_handler definition is invoked via
 * PCI error infrastructure, registered via pci
 */
static pci_ers_result_t
pci_error_detected(struct pci_dev *pdev, pci_channel_state_t state)
{
	struct hfi1_devdata *dd = pci_get_drvdata(pdev);
	pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED;

	switch (state) {
	case pci_channel_io_normal:
		dd_dev_info(dd, "State Normal, ignoring\n");
		break;

	case pci_channel_io_frozen:
		dd_dev_info(dd, "State Frozen, requesting reset\n");
		pci_disable_device(pdev);
		ret = PCI_ERS_RESULT_NEED_RESET;
		break;

	case pci_channel_io_perm_failure:
		if (dd) {
			dd_dev_info(dd, "State Permanent Failure, disabling\n");
			/* no more register accesses! */
			dd->flags &= ~HFI1_PRESENT;
			hfi1_disable_after_error(dd);
		}
		 /* else early, or other problem */
		ret =  PCI_ERS_RESULT_DISCONNECT;
		break;

	default: /* shouldn't happen */
		dd_dev_info(dd, "HFI1 PCI errors detected (state %d)\n",
			    state);
		break;
	}
	return ret;
}

static pci_ers_result_t
pci_mmio_enabled(struct pci_dev *pdev)
{
	u64 words = 0U;
	struct hfi1_devdata *dd = pci_get_drvdata(pdev);
	pci_ers_result_t ret = PCI_ERS_RESULT_RECOVERED;

	if (dd && dd->pport) {
		words = read_port_cntr(dd->pport, C_RX_WORDS, CNTR_INVALID_VL);
		if (words == ~0ULL)
			ret = PCI_ERS_RESULT_NEED_RESET;
		dd_dev_info(dd,
			    "HFI1 mmio_enabled function called, read wordscntr %Lx, returning %d\n",
			    words, ret);
	}
	return  ret;
}

static pci_ers_result_t
pci_slot_reset(struct pci_dev *pdev)
{
	struct hfi1_devdata *dd = pci_get_drvdata(pdev);

	dd_dev_info(dd, "HFI1 slot_reset function called, ignored\n");
	return PCI_ERS_RESULT_CAN_RECOVER;
}

static pci_ers_result_t
pci_link_reset(struct pci_dev *pdev)
{
	struct hfi1_devdata *dd = pci_get_drvdata(pdev);

	dd_dev_info(dd, "HFI1 link_reset function called, ignored\n");
	return PCI_ERS_RESULT_CAN_RECOVER;
}

static void
pci_resume(struct pci_dev *pdev)
{
	struct hfi1_devdata *dd = pci_get_drvdata(pdev);

	dd_dev_info(dd, "HFI1 resume function called\n");
	pci_cleanup_aer_uncorrect_error_status(pdev);
	/*
	 * Running jobs will fail, since it's asynchronous
	 * unlike sysfs-requested reset.   Better than
	 * doing nothing.
	 */
	hfi1_init(dd, 1); /* same as re-init after reset */
}

const struct pci_error_handlers hfi1_pci_err_handler = {
	.error_detected = pci_error_detected,
	.mmio_enabled = pci_mmio_enabled,
	.link_reset = pci_link_reset,
	.slot_reset = pci_slot_reset,
	.resume = pci_resume,
};

/*============================================================================*/
/* PCIe Gen3 support */

/*
 * This code is separated out because it is expected to be removed in the
 * final shipping product.  If not, then it will be revisited and items
 * will be moved to more standard locations.
 */

/* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_STS field values */
#define DL_STATUS_HFI0 0x1	/* hfi0 firmware download complete */
#define DL_STATUS_HFI1 0x2	/* hfi1 firmware download complete */
#define DL_STATUS_BOTH 0x3	/* hfi0 and hfi1 firmware download complete */

/* ASIC_PCI_SD_HOST_STATUS.FW_DNLD_ERR field values */
#define DL_ERR_NONE		0x0	/* no error */
#define DL_ERR_SWAP_PARITY	0x1	/* parity error in SerDes interrupt */
					/*   or response data */
#define DL_ERR_DISABLED	0x2	/* hfi disabled */
#define DL_ERR_SECURITY	0x3	/* security check failed */
#define DL_ERR_SBUS		0x4	/* SBus status error */
#define DL_ERR_XFR_PARITY	0x5	/* parity error during ROM transfer*/

/* gasket block secondary bus reset delay */
#define SBR_DELAY_US 200000	/* 200ms */

/* mask for PCIe capability register lnkctl2 target link speed */
#define LNKCTL2_TARGET_LINK_SPEED_MASK 0xf

static uint pcie_target = 3;
module_param(pcie_target, uint, S_IRUGO);
MODULE_PARM_DESC(pcie_target, "PCIe target speed (0 skip, 1-3 Gen1-3)");

static uint pcie_force;
module_param(pcie_force, uint, S_IRUGO);
MODULE_PARM_DESC(pcie_force, "Force driver to do a PCIe firmware download even if already at target speed");

static uint pcie_retry = 5;
module_param(pcie_retry, uint, S_IRUGO);
MODULE_PARM_DESC(pcie_retry, "Driver will try this many times to reach requested speed");

#define UNSET_PSET 255
#define DEFAULT_DISCRETE_PSET 2	/* discrete HFI */
#define DEFAULT_MCP_PSET 4	/* MCP HFI */
static uint pcie_pset = UNSET_PSET;
module_param(pcie_pset, uint, S_IRUGO);
MODULE_PARM_DESC(pcie_pset, "PCIe Eq Pset value to use, range is 0-10");

/* equalization columns */
#define PREC 0
#define ATTN 1
#define POST 2

/* discrete silicon preliminary equalization values */
static const u8 discrete_preliminary_eq[11][3] = {
	/* prec   attn   post */
	{  0x00,  0x00,  0x12 },	/* p0 */
	{  0x00,  0x00,  0x0c },	/* p1 */
	{  0x00,  0x00,  0x0f },	/* p2 */
	{  0x00,  0x00,  0x09 },	/* p3 */
	{  0x00,  0x00,  0x00 },	/* p4 */
	{  0x06,  0x00,  0x00 },	/* p5 */
	{  0x09,  0x00,  0x00 },	/* p6 */
	{  0x06,  0x00,  0x0f },	/* p7 */
	{  0x09,  0x00,  0x09 },	/* p8 */
	{  0x0c,  0x00,  0x00 },	/* p9 */
	{  0x00,  0x00,  0x18 },	/* p10 */
};

/* integrated silicon preliminary equalization values */
static const u8 integrated_preliminary_eq[11][3] = {
	/* prec   attn   post */
	{  0x00,  0x1e,  0x07 },	/* p0 */
	{  0x00,  0x1e,  0x05 },	/* p1 */
	{  0x00,  0x1e,  0x06 },	/* p2 */
	{  0x00,  0x1e,  0x04 },	/* p3 */
	{  0x00,  0x1e,  0x00 },	/* p4 */
	{  0x03,  0x1e,  0x00 },	/* p5 */
	{  0x04,  0x1e,  0x00 },	/* p6 */
	{  0x03,  0x1e,  0x06 },	/* p7 */
	{  0x03,  0x1e,  0x04 },	/* p8 */
	{  0x05,  0x1e,  0x00 },	/* p9 */
	{  0x00,  0x1e,  0x0a },	/* p10 */
};

/* helper to format the value to write to hardware */
#define eq_value(pre, curr, post) \
	((((u32)(pre)) << \
			PCIE_CFG_REG_PL102_GEN3_EQ_PRE_CURSOR_PSET_SHIFT) \
	| (((u32)(curr)) << PCIE_CFG_REG_PL102_GEN3_EQ_CURSOR_PSET_SHIFT) \
	| (((u32)(post)) << \
		PCIE_CFG_REG_PL102_GEN3_EQ_POST_CURSOR_PSET_SHIFT))

/*
 * Load the given EQ preset table into the PCIe hardware.
 */
static int load_eq_table(struct hfi1_devdata *dd, const u8 eq[11][3], u8 fs,
			 u8 div)
{
	struct pci_dev *pdev = dd->pcidev;
	u32 hit_error = 0;
	u32 violation;
	u32 i;
	u8 c_minus1, c0, c_plus1;

	for (i = 0; i < 11; i++) {
		/* set index */
		pci_write_config_dword(pdev, PCIE_CFG_REG_PL103, i);
		/* write the value */
		c_minus1 = eq[i][PREC] / div;
		c0 = fs - (eq[i][PREC] / div) - (eq[i][POST] / div);
		c_plus1 = eq[i][POST] / div;
		pci_write_config_dword(pdev, PCIE_CFG_REG_PL102,
			eq_value(c_minus1, c0, c_plus1));
		/* check if these coefficients violate EQ rules */
		pci_read_config_dword(dd->pcidev, PCIE_CFG_REG_PL105,
								&violation);
		if (violation
		    & PCIE_CFG_REG_PL105_GEN3_EQ_VIOLATE_COEF_RULES_SMASK){
			if (hit_error == 0) {
				dd_dev_err(dd,
					"Gen3 EQ Table Coefficient rule violations\n");
				dd_dev_err(dd, "         prec   attn   post\n");
			}
			dd_dev_err(dd, "   p%02d:   %02x     %02x     %02x\n",
				i, (u32)eq[i][0], (u32)eq[i][1], (u32)eq[i][2]);
			dd_dev_err(dd, "            %02x     %02x     %02x\n",
				(u32)c_minus1, (u32)c0, (u32)c_plus1);
			hit_error = 1;
		}
	}
	if (hit_error)
		return -EINVAL;
	return 0;
}

/*
 * Steps to be done after the PCIe firmware is downloaded and
 * before the SBR for the Pcie Gen3.
 * The hardware mutex is already being held.
 */
static void pcie_post_steps(struct hfi1_devdata *dd)
{
	int i;

	set_sbus_fast_mode(dd);
	/*
	 * Write to the PCIe PCSes to set the G3_LOCKED_NEXT bits to 1.
	 * This avoids a spurious framing error that can otherwise be
	 * generated by the MAC layer.
	 *
	 * Use individual addresses since no broadcast is set up.
	 */
	for (i = 0; i < NUM_PCIE_SERDES; i++) {
		sbus_request(dd, pcie_pcs_addrs[dd->hfi1_id][i],
			     0x03, WRITE_SBUS_RECEIVER, 0x00022132);
	}

	clear_sbus_fast_mode(dd);
}

/*
 * Trigger a secondary bus reset (SBR) on ourselves using our parent.
 *
 * Based on pci_parent_bus_reset() which is not exported by the
 * kernel core.
 */
static int trigger_sbr(struct hfi1_devdata *dd)
{
	struct pci_dev *dev = dd->pcidev;
	struct pci_dev *pdev;

	/* need a parent */
	if (!dev->bus->self) {
		dd_dev_err(dd, "%s: no parent device\n", __func__);
		return -ENOTTY;
	}

	/* should not be anyone else on the bus */
	list_for_each_entry(pdev, &dev->bus->devices, bus_list)
		if (pdev != dev) {
			dd_dev_err(dd,
				"%s: another device is on the same bus\n",
				__func__);
			return -ENOTTY;
		}

	/*
	 * A secondary bus reset (SBR) issues a hot reset to our device.
	 * The following routine does a 1s wait after the reset is dropped
	 * per PCI Trhfa (recovery time).  PCIe 3.0 section 6.6.1 -
	 * Conventional Reset, paragraph 3, line 35 also says that a 1s
	 * delay after a reset is required.  Per spec requirements,
	 * the link is either working or not after that point.
	 */
	pci_reset_bridge_secondary_bus(dev->bus->self);

	return 0;
}

/*
 * Write the given gasket interrupt register.
 */
static void write_gasket_interrupt(struct hfi1_devdata *dd, int index,
				   u16 code, u16 data)
{
	write_csr(dd, ASIC_PCIE_SD_INTRPT_LIST + (index * 8),
	    (((u64)code << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_CODE_SHIFT)
	    |((u64)data << ASIC_PCIE_SD_INTRPT_LIST_INTRPT_DATA_SHIFT)));
}

/*
 * Tell the gasket logic how to react to the reset.
 */
static void arm_gasket_logic(struct hfi1_devdata *dd)
{
	u64 reg;

	reg = (((u64)1 << dd->hfi1_id)
			<< ASIC_PCIE_SD_HOST_CMD_INTRPT_CMD_SHIFT)
		| ((u64)pcie_serdes_broadcast[dd->hfi1_id]
			<< ASIC_PCIE_SD_HOST_CMD_SBUS_RCVR_ADDR_SHIFT
		| ASIC_PCIE_SD_HOST_CMD_SBR_MODE_SMASK
		| ((u64)SBR_DELAY_US & ASIC_PCIE_SD_HOST_CMD_TIMER_MASK)
			<< ASIC_PCIE_SD_HOST_CMD_TIMER_SHIFT
		);
	write_csr(dd, ASIC_PCIE_SD_HOST_CMD, reg);
	/* read back to push the write */
	read_csr(dd, ASIC_PCIE_SD_HOST_CMD);
}

/*
 * Do all the steps needed to transition the PCIe link to Gen3 speed.
 */
int do_pcie_gen3_transition(struct hfi1_devdata *dd)
{
	struct pci_dev *parent;
	u64 fw_ctrl;
	u64 reg, therm;
	u32 reg32, fs, lf;
	u32 status, err;
	int ret;
	int do_retry, retry_count = 0;
	uint default_pset;
	u16 target_vector, target_speed;
	u16 lnkctl, lnkctl2, vendor;
	u8 nsbr = 1;
	u8 div;
	const u8 (*eq)[3];
	int return_error = 0;

	/* PCIe Gen3 is for the ASIC only */
	if (dd->icode != ICODE_RTL_SILICON)
		return 0;

	if (pcie_target == 1) {			/* target Gen1 */
		target_vector = GEN1_SPEED_VECTOR;
		target_speed = 2500;
	} else if (pcie_target == 2) {		/* target Gen2 */
		target_vector = GEN2_SPEED_VECTOR;
		target_speed = 5000;
	} else if (pcie_target == 3) {		/* target Gen3 */
		target_vector = GEN3_SPEED_VECTOR;
		target_speed = 8000;
	} else {
		/* off or invalid target - skip */
		dd_dev_info(dd, "%s: Skipping PCIe transition\n", __func__);
		return 0;
	}

	/* if already at target speed, done (unless forced) */
	if (dd->lbus_speed == target_speed) {
		dd_dev_info(dd, "%s: PCIe already at gen%d, %s\n", __func__,
			pcie_target,
			pcie_force ? "re-doing anyway" : "skipping");
		if (!pcie_force)
			return 0;
	}

	/*
	 * A0 needs an additional SBR
	 */
	if (is_a0(dd))
		nsbr++;

	/*
	 * Do the Gen3 transition.  Steps are those of the PCIe Gen3
	 * recipe.
	 */

	/* step 1: pcie link working in gen1/gen2 */

	/* step 2: if either side is not capable of Gen3, done */
	if (pcie_target == 3 && !dd->link_gen3_capable) {
		dd_dev_err(dd, "The PCIe link is not Gen3 capable\n");
		ret = -ENOSYS;
		goto done_no_mutex;
	}

	/* hold the HW mutex across the firmware download and SBR */
	ret = acquire_hw_mutex(dd);
	if (ret)
		return ret;

	/* make sure thermal polling is not causing interrupts */
	therm = read_csr(dd, ASIC_CFG_THERM_POLL_EN);
	if (therm) {
		write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x0);
		msleep(100);
		dd_dev_info(dd, "%s: Disabled therm polling\n",
			    __func__);
	}

retry:

	if (therm) {
		/*
		 * toggle SPICO_ENABLE to get back to the state
		 * just after the firmware load
		 */
		sbus_request(dd, SBUS_MASTER_BROADCAST, 0x01,
			WRITE_SBUS_RECEIVER, 0x00000040);
		sbus_request(dd, SBUS_MASTER_BROADCAST, 0x01,
			WRITE_SBUS_RECEIVER, 0x00000140);
	}

	/* step 3: download SBus Master firmware */
	/* step 4: download PCIe Gen3 SerDes firmware */
	dd_dev_info(dd, "%s: downloading firmware\n", __func__);
	ret = load_pcie_firmware(dd);
	if (ret)
		goto done;

	/* step 5: set up device parameter settings */
	dd_dev_info(dd, "%s: setting PCIe registers\n", __func__);

	/*
	 * PcieCfgSpcie1 - Link Control 3
	 * Leave at reset value.  No need to set PerfEq - link equalization
	 * will be performed automatically after the SBR when the target
	 * speed is 8GT/s.
	 */

	/* clear all 16 per-lane error bits (PCIe: Lane Error Status) */
	pci_write_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, 0xffff);

	/* step 5a: Set Synopsys Port Logic registers */

	/*
	 * PcieCfgRegPl2 - Port Force Link
	 *
	 * Set the low power field to 0x10 to avoid unnecessary power
	 * management messages.  All other fields are zero.
	 */
	reg32 = 0x10ul << PCIE_CFG_REG_PL2_LOW_PWR_ENT_CNT_SHIFT;
	pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL2, reg32);

	/*
	 * PcieCfgRegPl100 - Gen3 Control
	 *
	 * turn off PcieCfgRegPl100.Gen3ZRxDcNonCompl
	 * turn on PcieCfgRegPl100.EqEieosCnt (erratum)
	 * Everything else zero.
	 */
	reg32 = PCIE_CFG_REG_PL100_EQ_EIEOS_CNT_SMASK;
	pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL100, reg32);

	/*
	 * PcieCfgRegPl101 - Gen3 EQ FS and LF
	 * PcieCfgRegPl102 - Gen3 EQ Presets to Coefficients Mapping
	 * PcieCfgRegPl103 - Gen3 EQ Preset Index
	 * PcieCfgRegPl105 - Gen3 EQ Status
	 *
	 * Give initial EQ settings.
	 */
	if (dd->pcidev->device == PCI_DEVICE_ID_INTEL0) { /* discrete */
		/* 1000mV, FS=24, LF = 8 */
		fs = 24;
		lf = 8;
		div = 3;
		eq = discrete_preliminary_eq;
		default_pset = DEFAULT_DISCRETE_PSET;
	} else {
		/* 400mV, FS=29, LF = 9 */
		fs = 29;
		lf = 9;
		div = 1;
		eq = integrated_preliminary_eq;
		default_pset = DEFAULT_MCP_PSET;
	}
	pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL101,
		(fs << PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_FS_SHIFT)
		| (lf << PCIE_CFG_REG_PL101_GEN3_EQ_LOCAL_LF_SHIFT));
	ret = load_eq_table(dd, eq, fs, div);
	if (ret)
		goto done;

	/*
	 * PcieCfgRegPl106 - Gen3 EQ Control
	 *
	 * Set Gen3EqPsetReqVec, leave other fields 0.
	 */
	if (pcie_pset == UNSET_PSET)
		pcie_pset = default_pset;
	if (pcie_pset > 10) {	/* valid range is 0-10, inclusive */
		dd_dev_err(dd, "%s: Invalid Eq Pset %u, setting to %d\n",
			__func__, pcie_pset, default_pset);
		pcie_pset = default_pset;
	}
	dd_dev_info(dd, "%s: using EQ Pset %u\n", __func__, pcie_pset);
	pci_write_config_dword(dd->pcidev, PCIE_CFG_REG_PL106,
		((1 << pcie_pset)
			<< PCIE_CFG_REG_PL106_GEN3_EQ_PSET_REQ_VEC_SHIFT)
		| PCIE_CFG_REG_PL106_GEN3_EQ_EVAL2MS_DISABLE_SMASK
		| PCIE_CFG_REG_PL106_GEN3_EQ_PHASE23_EXIT_MODE_SMASK);

	/*
	 * step 5b: Do post firmware download steps via SBus
	 */
	dd_dev_info(dd, "%s: doing pcie post steps\n", __func__);
	pcie_post_steps(dd);

	/*
	 * step 5c: Program gasket interrupts
	 */
	/* set the Rx Bit Rate to REFCLK ratio */
	write_gasket_interrupt(dd, 0, 0x0006, 0x0050);
	/* disable pCal for PCIe Gen3 RX equalization */
	write_gasket_interrupt(dd, 1, 0x0026, 0x5b01);
	/*
	 * Enable iCal for PCIe Gen3 RX equalization, and set which
	 * evaluation of RX_EQ_EVAL will launch the iCal procedure.
	 */
	write_gasket_interrupt(dd, 2, 0x0026, 0x5202);
	/* terminate list */
	write_gasket_interrupt(dd, 3, 0x0000, 0x0000);

	/*
	 * step 5d: program XMT margin
	 * Right now, leave the default alone.  To change, do a
	 * read-modify-write of:
	 *	CcePcieCtrl.XmtMargin
	 *	CcePcieCtrl.XmitMarginOverwriteEnable
	 */

	/* step 5e: disable active state power management (ASPM) */
	dd_dev_info(dd, "%s: clearing ASPM\n", __func__);
	pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL, &lnkctl);
	lnkctl &= ~PCI_EXP_LNKCTL_ASPMC;
	pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL, lnkctl);

	/*
	 * step 5f: clear DirectSpeedChange
	 * PcieCfgRegPl67.DirectSpeedChange must be zero to prevent the
	 * change in the speed target from starting before we are ready.
	 * This field defaults to 0 and we are not changing it, so nothing
	 * needs to be done.
	 */

	/* step 5g: Set target link speed */
	/*
	 * Set target link speed to be target on both device and parent.
	 * On setting the parent: Some system BIOSs "helpfully" set the
	 * parent target speed to Gen2 to match the ASIC's initial speed.
	 * We can set the target Gen3 because we have already checked
	 * that it is Gen3 capable earlier.
	 */
	dd_dev_info(dd, "%s: setting parent target link speed\n", __func__);
	parent = dd->pcidev->bus->self;
	pcie_capability_read_word(parent, PCI_EXP_LNKCTL2, &lnkctl2);
	dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__,
		(u32)lnkctl2);
	/* only write to parent if target is not as high as ours */
	if ((lnkctl2 & LNKCTL2_TARGET_LINK_SPEED_MASK) < target_vector) {
		lnkctl2 &= ~LNKCTL2_TARGET_LINK_SPEED_MASK;
		lnkctl2 |= target_vector;
		dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__,
			(u32)lnkctl2);
		pcie_capability_write_word(parent, PCI_EXP_LNKCTL2, lnkctl2);
	} else {
		dd_dev_info(dd, "%s: ..target speed is OK\n", __func__);
	}

	dd_dev_info(dd, "%s: setting target link speed\n", __func__);
	pcie_capability_read_word(dd->pcidev, PCI_EXP_LNKCTL2, &lnkctl2);
	dd_dev_info(dd, "%s: ..old link control2: 0x%x\n", __func__,
		(u32)lnkctl2);
	lnkctl2 &= ~LNKCTL2_TARGET_LINK_SPEED_MASK;
	lnkctl2 |= target_vector;
	dd_dev_info(dd, "%s: ..new link control2: 0x%x\n", __func__,
		(u32)lnkctl2);
	pcie_capability_write_word(dd->pcidev, PCI_EXP_LNKCTL2, lnkctl2);

	/* step 5h: arm gasket logic */
	/* hold DC in reset across the SBR */
	write_csr(dd, CCE_DC_CTRL, CCE_DC_CTRL_DC_RESET_SMASK);
	(void) read_csr(dd, CCE_DC_CTRL); /* DC reset hold */
	/* save firmware control across the SBR */
	fw_ctrl = read_csr(dd, MISC_CFG_FW_CTRL);

	dd_dev_info(dd, "%s: arming gasket logic\n", __func__);
	arm_gasket_logic(dd);

	/*
	 * step 6: quiesce PCIe link
	 * The chip has already been reset, so there will be no traffic
	 * from the chip.  Linux has no easy way to enforce that it will
	 * not try to access the device, so we just need to hope it doesn't
	 * do it while we are doing the reset.
	 */

	/*
	 * step 7: initiate the secondary bus reset (SBR)
	 * step 8: hardware brings the links back up
	 * step 9: wait for link speed transition to be complete
	 */
	dd_dev_info(dd, "%s: calling trigger_sbr\n", __func__);
	ret = trigger_sbr(dd);
	if (ret)
		goto done;

	/* step 10: decide what to do next */

	/* check if we can read PCI space */
	ret = pci_read_config_word(dd->pcidev, PCI_VENDOR_ID, &vendor);
	if (ret) {
		dd_dev_info(dd,
			"%s: read of VendorID failed after SBR, err %d\n",
			__func__, ret);
		return_error = 1;
		goto done;
	}
	if (vendor == 0xffff) {
		dd_dev_info(dd, "%s: VendorID is all 1s after SBR\n", __func__);
		return_error = 1;
		ret = -EIO;
		goto done;
	}

	/* restore PCI space registers we know were reset */
	dd_dev_info(dd, "%s: calling restore_pci_variables\n", __func__);
	restore_pci_variables(dd);
	/* restore firmware control */
	write_csr(dd, MISC_CFG_FW_CTRL, fw_ctrl);

	/*
	 * Check the gasket block status.
	 *
	 * This is the first CSR read after the SBR.  If the read returns
	 * all 1s (fails), the link did not make it back.
	 *
	 * Once we're sure we can read and write, clear the DC reset after
	 * the SBR.  Then check for any per-lane errors. Then look over
	 * the status.
	 */
	reg = read_csr(dd, ASIC_PCIE_SD_HOST_STATUS);
	dd_dev_info(dd, "%s: gasket block status: 0x%llx\n", __func__, reg);
	if (reg == ~0ull) {	/* PCIe read failed/timeout */
		dd_dev_err(dd, "SBR failed - unable to read from device\n");
		return_error = 1;
		ret = -ENOSYS;
		goto done;
	}

	/* clear the DC reset */
	write_csr(dd, CCE_DC_CTRL, 0);

	/* Set the LED off */
	if (is_a0(dd))
		setextled(dd, 0);

	/* check for any per-lane errors */
	pci_read_config_dword(dd->pcidev, PCIE_CFG_SPCIE2, &reg32);
	dd_dev_info(dd, "%s: per-lane errors: 0x%x\n", __func__, reg32);

	/* extract status, look for our HFI */
	status = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_SHIFT)
			& ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_STS_MASK;
	if ((status & (1 << dd->hfi1_id)) == 0) {
		dd_dev_err(dd,
			"%s: gasket status 0x%x, expecting 0x%x\n",
			__func__, status, 1 << dd->hfi1_id);
		ret = -EIO;
		goto done;
	}

	/* extract error */
	err = (reg >> ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_SHIFT)
		& ASIC_PCIE_SD_HOST_STATUS_FW_DNLD_ERR_MASK;
	if (err) {
		dd_dev_err(dd, "%s: gasket error %d\n", __func__, err);
		ret = -EIO;
		goto done;
	}

	/* update our link information cache */
	update_lbus_info(dd);
	dd_dev_info(dd, "%s: new speed and width: %s\n", __func__,
		dd->lbus_info);

	if (dd->lbus_speed != target_speed) { /* not target */
		/* maybe retry */
		do_retry = retry_count < pcie_retry;
		dd_dev_err(dd, "PCIe link speed did not switch to Gen%d%s\n",
			pcie_target, do_retry ? ", retrying" : "");
		retry_count++;
		if (do_retry) {
			msleep(100); /* allow time to settle */
			goto retry;
		}
		ret = -EIO;
	}

done:
	if (therm) {
		write_csr(dd, ASIC_CFG_THERM_POLL_EN, 0x1);
		msleep(100);
		dd_dev_info(dd, "%s: Re-enable therm polling\n",
			    __func__);
	}
	release_hw_mutex(dd);
done_no_mutex:
	/* return no error if it is OK to be at current speed */
	if (ret && !return_error) {
		dd_dev_err(dd, "Proceeding at current speed PCIe speed\n");
		ret = 0;
	}

	dd_dev_info(dd, "%s: done\n", __func__);
	return ret;
}