| /* | |
| * adv7183.c Analog Devices ADV7183 video decoder driver | |
| * | |
| * Copyright (c) 2011 Analog Devices Inc. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/errno.h> | |
| #include <linux/gpio.h> | |
| #include <linux/i2c.h> | |
| #include <linux/init.h> | |
| #include <linux/module.h> | |
| #include <linux/slab.h> | |
| #include <linux/types.h> | |
| #include <linux/videodev2.h> | |
| #include <media/adv7183.h> | |
| #include <media/v4l2-ctrls.h> | |
| #include <media/v4l2-device.h> | |
| #include "adv7183_regs.h" | |
| struct adv7183 { | |
| struct v4l2_subdev sd; | |
| struct v4l2_ctrl_handler hdl; | |
| v4l2_std_id std; /* Current set standard */ | |
| u32 input; | |
| u32 output; | |
| unsigned reset_pin; | |
| unsigned oe_pin; | |
| struct v4l2_mbus_framefmt fmt; | |
| }; | |
| /* EXAMPLES USING 27 MHz CLOCK | |
| * Mode 1 CVBS Input (Composite Video on AIN5) | |
| * All standards are supported through autodetect, 8-bit, 4:2:2, ITU-R BT.656 output on P15 to P8. | |
| */ | |
| static const unsigned char adv7183_init_regs[] = { | |
| ADV7183_IN_CTRL, 0x04, /* CVBS input on AIN5 */ | |
| ADV7183_DIGI_CLAMP_CTRL_1, 0x00, /* Slow down digital clamps */ | |
| ADV7183_SHAP_FILT_CTRL, 0x41, /* Set CSFM to SH1 */ | |
| ADV7183_ADC_CTRL, 0x16, /* Power down ADC 1 and ADC 2 */ | |
| ADV7183_CTI_DNR_CTRL_4, 0x04, /* Set DNR threshold to 4 for flat response */ | |
| /* ADI recommended programming sequence */ | |
| ADV7183_ADI_CTRL, 0x80, | |
| ADV7183_CTI_DNR_CTRL_4, 0x20, | |
| 0x52, 0x18, | |
| 0x58, 0xED, | |
| 0x77, 0xC5, | |
| 0x7C, 0x93, | |
| 0x7D, 0x00, | |
| 0xD0, 0x48, | |
| 0xD5, 0xA0, | |
| 0xD7, 0xEA, | |
| ADV7183_SD_SATURATION_CR, 0x3E, | |
| ADV7183_PAL_V_END, 0x3E, | |
| ADV7183_PAL_F_TOGGLE, 0x0F, | |
| ADV7183_ADI_CTRL, 0x00, | |
| }; | |
| static inline struct adv7183 *to_adv7183(struct v4l2_subdev *sd) | |
| { | |
| return container_of(sd, struct adv7183, sd); | |
| } | |
| static inline struct v4l2_subdev *to_sd(struct v4l2_ctrl *ctrl) | |
| { | |
| return &container_of(ctrl->handler, struct adv7183, hdl)->sd; | |
| } | |
| static inline int adv7183_read(struct v4l2_subdev *sd, unsigned char reg) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| return i2c_smbus_read_byte_data(client, reg); | |
| } | |
| static inline int adv7183_write(struct v4l2_subdev *sd, unsigned char reg, | |
| unsigned char value) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| return i2c_smbus_write_byte_data(client, reg, value); | |
| } | |
| static int adv7183_writeregs(struct v4l2_subdev *sd, | |
| const unsigned char *regs, unsigned int num) | |
| { | |
| unsigned char reg, data; | |
| unsigned int cnt = 0; | |
| if (num & 0x1) { | |
| v4l2_err(sd, "invalid regs array\n"); | |
| return -1; | |
| } | |
| while (cnt < num) { | |
| reg = *regs++; | |
| data = *regs++; | |
| cnt += 2; | |
| adv7183_write(sd, reg, data); | |
| } | |
| return 0; | |
| } | |
| static int adv7183_log_status(struct v4l2_subdev *sd) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| v4l2_info(sd, "adv7183: Input control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_IN_CTRL)); | |
| v4l2_info(sd, "adv7183: Video selection = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_VD_SEL)); | |
| v4l2_info(sd, "adv7183: Output control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_OUT_CTRL)); | |
| v4l2_info(sd, "adv7183: Extended output control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_EXT_OUT_CTRL)); | |
| v4l2_info(sd, "adv7183: Autodetect enable = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_AUTO_DET_EN)); | |
| v4l2_info(sd, "adv7183: Contrast = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_CONTRAST)); | |
| v4l2_info(sd, "adv7183: Brightness = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_BRIGHTNESS)); | |
| v4l2_info(sd, "adv7183: Hue = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_HUE)); | |
| v4l2_info(sd, "adv7183: Default value Y = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_DEF_Y)); | |
| v4l2_info(sd, "adv7183: Default value C = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_DEF_C)); | |
| v4l2_info(sd, "adv7183: ADI control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_ADI_CTRL)); | |
| v4l2_info(sd, "adv7183: Power Management = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_POW_MANAGE)); | |
| v4l2_info(sd, "adv7183: Status 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_STATUS_1), | |
| adv7183_read(sd, ADV7183_STATUS_2), | |
| adv7183_read(sd, ADV7183_STATUS_3)); | |
| v4l2_info(sd, "adv7183: Ident = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_IDENT)); | |
| v4l2_info(sd, "adv7183: Analog clamp control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_ANAL_CLAMP_CTRL)); | |
| v4l2_info(sd, "adv7183: Digital clamp control 1 = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_DIGI_CLAMP_CTRL_1)); | |
| v4l2_info(sd, "adv7183: Shaping filter control 1 and 2 = 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_SHAP_FILT_CTRL), | |
| adv7183_read(sd, ADV7183_SHAP_FILT_CTRL_2)); | |
| v4l2_info(sd, "adv7183: Comb filter control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_COMB_FILT_CTRL)); | |
| v4l2_info(sd, "adv7183: ADI control 2 = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_ADI_CTRL_2)); | |
| v4l2_info(sd, "adv7183: Pixel delay control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_PIX_DELAY_CTRL)); | |
| v4l2_info(sd, "adv7183: Misc gain control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_MISC_GAIN_CTRL)); | |
| v4l2_info(sd, "adv7183: AGC mode control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_AGC_MODE_CTRL)); | |
| v4l2_info(sd, "adv7183: Chroma gain control 1 and 2 = 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_CHRO_GAIN_CTRL_1), | |
| adv7183_read(sd, ADV7183_CHRO_GAIN_CTRL_2)); | |
| v4l2_info(sd, "adv7183: Luma gain control 1 and 2 = 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_LUMA_GAIN_CTRL_1), | |
| adv7183_read(sd, ADV7183_LUMA_GAIN_CTRL_2)); | |
| v4l2_info(sd, "adv7183: Vsync field control 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_VS_FIELD_CTRL_1), | |
| adv7183_read(sd, ADV7183_VS_FIELD_CTRL_2), | |
| adv7183_read(sd, ADV7183_VS_FIELD_CTRL_3)); | |
| v4l2_info(sd, "adv7183: Hsync position control 1 2 and 3 = 0x%02x 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_HS_POS_CTRL_1), | |
| adv7183_read(sd, ADV7183_HS_POS_CTRL_2), | |
| adv7183_read(sd, ADV7183_HS_POS_CTRL_3)); | |
| v4l2_info(sd, "adv7183: Polarity = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_POLARITY)); | |
| v4l2_info(sd, "adv7183: ADC control = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_ADC_CTRL)); | |
| v4l2_info(sd, "adv7183: SD offset Cb and Cr = 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_SD_OFFSET_CB), | |
| adv7183_read(sd, ADV7183_SD_OFFSET_CR)); | |
| v4l2_info(sd, "adv7183: SD saturation Cb and Cr = 0x%02x 0x%02x\n", | |
| adv7183_read(sd, ADV7183_SD_SATURATION_CB), | |
| adv7183_read(sd, ADV7183_SD_SATURATION_CR)); | |
| v4l2_info(sd, "adv7183: Drive strength = 0x%02x\n", | |
| adv7183_read(sd, ADV7183_DRIVE_STR)); | |
| v4l2_ctrl_handler_log_status(&decoder->hdl, sd->name); | |
| return 0; | |
| } | |
| static int adv7183_g_std(struct v4l2_subdev *sd, v4l2_std_id *std) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| *std = decoder->std; | |
| return 0; | |
| } | |
| static int adv7183_s_std(struct v4l2_subdev *sd, v4l2_std_id std) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| int reg; | |
| reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF; | |
| if (std == V4L2_STD_PAL_60) | |
| reg |= 0x60; | |
| else if (std == V4L2_STD_NTSC_443) | |
| reg |= 0x70; | |
| else if (std == V4L2_STD_PAL_N) | |
| reg |= 0x90; | |
| else if (std == V4L2_STD_PAL_M) | |
| reg |= 0xA0; | |
| else if (std == V4L2_STD_PAL_Nc) | |
| reg |= 0xC0; | |
| else if (std & V4L2_STD_PAL) | |
| reg |= 0x80; | |
| else if (std & V4L2_STD_NTSC) | |
| reg |= 0x50; | |
| else if (std & V4L2_STD_SECAM) | |
| reg |= 0xE0; | |
| else | |
| return -EINVAL; | |
| adv7183_write(sd, ADV7183_IN_CTRL, reg); | |
| decoder->std = std; | |
| return 0; | |
| } | |
| static int adv7183_reset(struct v4l2_subdev *sd, u32 val) | |
| { | |
| int reg; | |
| reg = adv7183_read(sd, ADV7183_POW_MANAGE) | 0x80; | |
| adv7183_write(sd, ADV7183_POW_MANAGE, reg); | |
| /* wait 5ms before any further i2c writes are performed */ | |
| usleep_range(5000, 10000); | |
| return 0; | |
| } | |
| static int adv7183_s_routing(struct v4l2_subdev *sd, | |
| u32 input, u32 output, u32 config) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| int reg; | |
| if ((input > ADV7183_COMPONENT1) || (output > ADV7183_16BIT_OUT)) | |
| return -EINVAL; | |
| if (input != decoder->input) { | |
| decoder->input = input; | |
| reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF0; | |
| switch (input) { | |
| case ADV7183_COMPOSITE1: | |
| reg |= 0x1; | |
| break; | |
| case ADV7183_COMPOSITE2: | |
| reg |= 0x2; | |
| break; | |
| case ADV7183_COMPOSITE3: | |
| reg |= 0x3; | |
| break; | |
| case ADV7183_COMPOSITE4: | |
| reg |= 0x4; | |
| break; | |
| case ADV7183_COMPOSITE5: | |
| reg |= 0x5; | |
| break; | |
| case ADV7183_COMPOSITE6: | |
| reg |= 0xB; | |
| break; | |
| case ADV7183_COMPOSITE7: | |
| reg |= 0xC; | |
| break; | |
| case ADV7183_COMPOSITE8: | |
| reg |= 0xD; | |
| break; | |
| case ADV7183_COMPOSITE9: | |
| reg |= 0xE; | |
| break; | |
| case ADV7183_COMPOSITE10: | |
| reg |= 0xF; | |
| break; | |
| case ADV7183_SVIDEO0: | |
| reg |= 0x6; | |
| break; | |
| case ADV7183_SVIDEO1: | |
| reg |= 0x7; | |
| break; | |
| case ADV7183_SVIDEO2: | |
| reg |= 0x8; | |
| break; | |
| case ADV7183_COMPONENT0: | |
| reg |= 0x9; | |
| break; | |
| case ADV7183_COMPONENT1: | |
| reg |= 0xA; | |
| break; | |
| default: | |
| break; | |
| } | |
| adv7183_write(sd, ADV7183_IN_CTRL, reg); | |
| } | |
| if (output != decoder->output) { | |
| decoder->output = output; | |
| reg = adv7183_read(sd, ADV7183_OUT_CTRL) & 0xC0; | |
| switch (output) { | |
| case ADV7183_16BIT_OUT: | |
| reg |= 0x9; | |
| break; | |
| default: | |
| reg |= 0xC; | |
| break; | |
| } | |
| adv7183_write(sd, ADV7183_OUT_CTRL, reg); | |
| } | |
| return 0; | |
| } | |
| static int adv7183_s_ctrl(struct v4l2_ctrl *ctrl) | |
| { | |
| struct v4l2_subdev *sd = to_sd(ctrl); | |
| int val = ctrl->val; | |
| switch (ctrl->id) { | |
| case V4L2_CID_BRIGHTNESS: | |
| if (val < 0) | |
| val = 127 - val; | |
| adv7183_write(sd, ADV7183_BRIGHTNESS, val); | |
| break; | |
| case V4L2_CID_CONTRAST: | |
| adv7183_write(sd, ADV7183_CONTRAST, val); | |
| break; | |
| case V4L2_CID_SATURATION: | |
| adv7183_write(sd, ADV7183_SD_SATURATION_CB, val >> 8); | |
| adv7183_write(sd, ADV7183_SD_SATURATION_CR, (val & 0xFF)); | |
| break; | |
| case V4L2_CID_HUE: | |
| adv7183_write(sd, ADV7183_SD_OFFSET_CB, val >> 8); | |
| adv7183_write(sd, ADV7183_SD_OFFSET_CR, (val & 0xFF)); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return 0; | |
| } | |
| static int adv7183_querystd(struct v4l2_subdev *sd, v4l2_std_id *std) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| int reg; | |
| /* enable autodetection block */ | |
| reg = adv7183_read(sd, ADV7183_IN_CTRL) & 0xF; | |
| adv7183_write(sd, ADV7183_IN_CTRL, reg); | |
| /* wait autodetection switch */ | |
| mdelay(10); | |
| /* get autodetection result */ | |
| reg = adv7183_read(sd, ADV7183_STATUS_1); | |
| switch ((reg >> 0x4) & 0x7) { | |
| case 0: | |
| *std &= V4L2_STD_NTSC; | |
| break; | |
| case 1: | |
| *std &= V4L2_STD_NTSC_443; | |
| break; | |
| case 2: | |
| *std &= V4L2_STD_PAL_M; | |
| break; | |
| case 3: | |
| *std &= V4L2_STD_PAL_60; | |
| break; | |
| case 4: | |
| *std &= V4L2_STD_PAL; | |
| break; | |
| case 5: | |
| *std &= V4L2_STD_SECAM; | |
| break; | |
| case 6: | |
| *std &= V4L2_STD_PAL_Nc; | |
| break; | |
| case 7: | |
| *std &= V4L2_STD_SECAM; | |
| break; | |
| default: | |
| *std = V4L2_STD_UNKNOWN; | |
| break; | |
| } | |
| /* after std detection, write back user set std */ | |
| adv7183_s_std(sd, decoder->std); | |
| return 0; | |
| } | |
| static int adv7183_g_input_status(struct v4l2_subdev *sd, u32 *status) | |
| { | |
| int reg; | |
| *status = V4L2_IN_ST_NO_SIGNAL; | |
| reg = adv7183_read(sd, ADV7183_STATUS_1); | |
| if (reg < 0) | |
| return reg; | |
| if (reg & 0x1) | |
| *status = 0; | |
| return 0; | |
| } | |
| static int adv7183_enum_mbus_fmt(struct v4l2_subdev *sd, unsigned index, | |
| enum v4l2_mbus_pixelcode *code) | |
| { | |
| if (index > 0) | |
| return -EINVAL; | |
| *code = V4L2_MBUS_FMT_UYVY8_2X8; | |
| return 0; | |
| } | |
| static int adv7183_try_mbus_fmt(struct v4l2_subdev *sd, | |
| struct v4l2_mbus_framefmt *fmt) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| fmt->code = V4L2_MBUS_FMT_UYVY8_2X8; | |
| fmt->colorspace = V4L2_COLORSPACE_SMPTE170M; | |
| if (decoder->std & V4L2_STD_525_60) { | |
| fmt->field = V4L2_FIELD_SEQ_TB; | |
| fmt->width = 720; | |
| fmt->height = 480; | |
| } else { | |
| fmt->field = V4L2_FIELD_SEQ_BT; | |
| fmt->width = 720; | |
| fmt->height = 576; | |
| } | |
| return 0; | |
| } | |
| static int adv7183_s_mbus_fmt(struct v4l2_subdev *sd, | |
| struct v4l2_mbus_framefmt *fmt) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| adv7183_try_mbus_fmt(sd, fmt); | |
| decoder->fmt = *fmt; | |
| return 0; | |
| } | |
| static int adv7183_g_mbus_fmt(struct v4l2_subdev *sd, | |
| struct v4l2_mbus_framefmt *fmt) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| *fmt = decoder->fmt; | |
| return 0; | |
| } | |
| static int adv7183_s_stream(struct v4l2_subdev *sd, int enable) | |
| { | |
| struct adv7183 *decoder = to_adv7183(sd); | |
| if (enable) | |
| gpio_set_value(decoder->oe_pin, 0); | |
| else | |
| gpio_set_value(decoder->oe_pin, 1); | |
| udelay(1); | |
| return 0; | |
| } | |
| #ifdef CONFIG_VIDEO_ADV_DEBUG | |
| static int adv7183_g_register(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg) | |
| { | |
| reg->val = adv7183_read(sd, reg->reg & 0xff); | |
| reg->size = 1; | |
| return 0; | |
| } | |
| static int adv7183_s_register(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg) | |
| { | |
| adv7183_write(sd, reg->reg & 0xff, reg->val & 0xff); | |
| return 0; | |
| } | |
| #endif | |
| static const struct v4l2_ctrl_ops adv7183_ctrl_ops = { | |
| .s_ctrl = adv7183_s_ctrl, | |
| }; | |
| static const struct v4l2_subdev_core_ops adv7183_core_ops = { | |
| .log_status = adv7183_log_status, | |
| .g_std = adv7183_g_std, | |
| .s_std = adv7183_s_std, | |
| .reset = adv7183_reset, | |
| #ifdef CONFIG_VIDEO_ADV_DEBUG | |
| .g_register = adv7183_g_register, | |
| .s_register = adv7183_s_register, | |
| #endif | |
| }; | |
| static const struct v4l2_subdev_video_ops adv7183_video_ops = { | |
| .s_routing = adv7183_s_routing, | |
| .querystd = adv7183_querystd, | |
| .g_input_status = adv7183_g_input_status, | |
| .enum_mbus_fmt = adv7183_enum_mbus_fmt, | |
| .try_mbus_fmt = adv7183_try_mbus_fmt, | |
| .s_mbus_fmt = adv7183_s_mbus_fmt, | |
| .g_mbus_fmt = adv7183_g_mbus_fmt, | |
| .s_stream = adv7183_s_stream, | |
| }; | |
| static const struct v4l2_subdev_ops adv7183_ops = { | |
| .core = &adv7183_core_ops, | |
| .video = &adv7183_video_ops, | |
| }; | |
| static int adv7183_probe(struct i2c_client *client, | |
| const struct i2c_device_id *id) | |
| { | |
| struct adv7183 *decoder; | |
| struct v4l2_subdev *sd; | |
| struct v4l2_ctrl_handler *hdl; | |
| int ret; | |
| struct v4l2_mbus_framefmt fmt; | |
| const unsigned *pin_array; | |
| /* Check if the adapter supports the needed features */ | |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) | |
| return -EIO; | |
| v4l_info(client, "chip found @ 0x%02x (%s)\n", | |
| client->addr << 1, client->adapter->name); | |
| pin_array = client->dev.platform_data; | |
| if (pin_array == NULL) | |
| return -EINVAL; | |
| decoder = devm_kzalloc(&client->dev, sizeof(*decoder), GFP_KERNEL); | |
| if (decoder == NULL) | |
| return -ENOMEM; | |
| decoder->reset_pin = pin_array[0]; | |
| decoder->oe_pin = pin_array[1]; | |
| if (devm_gpio_request_one(&client->dev, decoder->reset_pin, | |
| GPIOF_OUT_INIT_LOW, "ADV7183 Reset")) { | |
| v4l_err(client, "failed to request GPIO %d\n", decoder->reset_pin); | |
| return -EBUSY; | |
| } | |
| if (devm_gpio_request_one(&client->dev, decoder->oe_pin, | |
| GPIOF_OUT_INIT_HIGH, | |
| "ADV7183 Output Enable")) { | |
| v4l_err(client, "failed to request GPIO %d\n", decoder->oe_pin); | |
| return -EBUSY; | |
| } | |
| sd = &decoder->sd; | |
| v4l2_i2c_subdev_init(sd, client, &adv7183_ops); | |
| hdl = &decoder->hdl; | |
| v4l2_ctrl_handler_init(hdl, 4); | |
| v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | |
| V4L2_CID_BRIGHTNESS, -128, 127, 1, 0); | |
| v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | |
| V4L2_CID_CONTRAST, 0, 0xFF, 1, 0x80); | |
| v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | |
| V4L2_CID_SATURATION, 0, 0xFFFF, 1, 0x8080); | |
| v4l2_ctrl_new_std(hdl, &adv7183_ctrl_ops, | |
| V4L2_CID_HUE, 0, 0xFFFF, 1, 0x8080); | |
| /* hook the control handler into the driver */ | |
| sd->ctrl_handler = hdl; | |
| if (hdl->error) { | |
| ret = hdl->error; | |
| v4l2_ctrl_handler_free(hdl); | |
| return ret; | |
| } | |
| /* v4l2 doesn't support an autodetect standard, pick PAL as default */ | |
| decoder->std = V4L2_STD_PAL; | |
| decoder->input = ADV7183_COMPOSITE4; | |
| decoder->output = ADV7183_8BIT_OUT; | |
| /* reset chip */ | |
| /* reset pulse width at least 5ms */ | |
| mdelay(10); | |
| gpio_set_value(decoder->reset_pin, 1); | |
| /* wait 5ms before any further i2c writes are performed */ | |
| mdelay(5); | |
| adv7183_writeregs(sd, adv7183_init_regs, ARRAY_SIZE(adv7183_init_regs)); | |
| adv7183_s_std(sd, decoder->std); | |
| fmt.width = 720; | |
| fmt.height = 576; | |
| adv7183_s_mbus_fmt(sd, &fmt); | |
| /* initialize the hardware to the default control values */ | |
| ret = v4l2_ctrl_handler_setup(hdl); | |
| if (ret) { | |
| v4l2_ctrl_handler_free(hdl); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int adv7183_remove(struct i2c_client *client) | |
| { | |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); | |
| v4l2_device_unregister_subdev(sd); | |
| v4l2_ctrl_handler_free(sd->ctrl_handler); | |
| return 0; | |
| } | |
| static const struct i2c_device_id adv7183_id[] = { | |
| {"adv7183", 0}, | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, adv7183_id); | |
| static struct i2c_driver adv7183_driver = { | |
| .driver = { | |
| .owner = THIS_MODULE, | |
| .name = "adv7183", | |
| }, | |
| .probe = adv7183_probe, | |
| .remove = adv7183_remove, | |
| .id_table = adv7183_id, | |
| }; | |
| module_i2c_driver(adv7183_driver); | |
| MODULE_DESCRIPTION("Analog Devices ADV7183 video decoder driver"); | |
| MODULE_AUTHOR("Scott Jiang <Scott.Jiang.Linux@gmail.com>"); | |
| MODULE_LICENSE("GPL v2"); |