| /* | |
| mii.c: MII interface library | |
| Maintained by Jeff Garzik <jgarzik@pobox.com> | |
| Copyright 2001,2002 Jeff Garzik | |
| Various code came from myson803.c and other files by | |
| Donald Becker. Copyright: | |
| Written 1998-2002 by Donald Becker. | |
| This software may be used and distributed according | |
| to the terms of the GNU General Public License (GPL), | |
| incorporated herein by reference. Drivers based on | |
| or derived from this code fall under the GPL and must | |
| retain the authorship, copyright and license notice. | |
| This file is not a complete program and may only be | |
| used when the entire operating system is licensed | |
| under the GPL. | |
| The author may be reached as becker@scyld.com, or C/O | |
| Scyld Computing Corporation | |
| 410 Severn Ave., Suite 210 | |
| Annapolis MD 21403 | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/ethtool.h> | |
| #include <linux/mii.h> | |
| static u32 mii_get_an(struct mii_if_info *mii, u16 addr) | |
| { | |
| int advert; | |
| advert = mii->mdio_read(mii->dev, mii->phy_id, addr); | |
| return mii_lpa_to_ethtool_lpa_t(advert); | |
| } | |
| /** | |
| * mii_ethtool_gset - get settings that are specified in @ecmd | |
| * @mii: MII interface | |
| * @ecmd: requested ethtool_cmd | |
| * | |
| * The @ecmd parameter is expected to have been cleared before calling | |
| * mii_ethtool_gset(). | |
| * | |
| * Returns 0 for success, negative on error. | |
| */ | |
| int mii_ethtool_gset(struct mii_if_info *mii, struct ethtool_cmd *ecmd) | |
| { | |
| struct net_device *dev = mii->dev; | |
| u16 bmcr, bmsr, ctrl1000 = 0, stat1000 = 0; | |
| u32 nego; | |
| ecmd->supported = | |
| (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | | |
| SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | | |
| SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII); | |
| if (mii->supports_gmii) | |
| ecmd->supported |= SUPPORTED_1000baseT_Half | | |
| SUPPORTED_1000baseT_Full; | |
| /* only supports twisted-pair */ | |
| ecmd->port = PORT_MII; | |
| /* only supports internal transceiver */ | |
| ecmd->transceiver = XCVR_INTERNAL; | |
| /* this isn't fully supported at higher layers */ | |
| ecmd->phy_address = mii->phy_id; | |
| ecmd->mdio_support = ETH_MDIO_SUPPORTS_C22; | |
| ecmd->advertising = ADVERTISED_TP | ADVERTISED_MII; | |
| bmcr = mii->mdio_read(dev, mii->phy_id, MII_BMCR); | |
| bmsr = mii->mdio_read(dev, mii->phy_id, MII_BMSR); | |
| if (mii->supports_gmii) { | |
| ctrl1000 = mii->mdio_read(dev, mii->phy_id, MII_CTRL1000); | |
| stat1000 = mii->mdio_read(dev, mii->phy_id, MII_STAT1000); | |
| } | |
| if (bmcr & BMCR_ANENABLE) { | |
| ecmd->advertising |= ADVERTISED_Autoneg; | |
| ecmd->autoneg = AUTONEG_ENABLE; | |
| ecmd->advertising |= mii_get_an(mii, MII_ADVERTISE); | |
| if (mii->supports_gmii) | |
| ecmd->advertising |= | |
| mii_ctrl1000_to_ethtool_adv_t(ctrl1000); | |
| if (bmsr & BMSR_ANEGCOMPLETE) { | |
| ecmd->lp_advertising = mii_get_an(mii, MII_LPA); | |
| ecmd->lp_advertising |= | |
| mii_stat1000_to_ethtool_lpa_t(stat1000); | |
| } else { | |
| ecmd->lp_advertising = 0; | |
| } | |
| nego = ecmd->advertising & ecmd->lp_advertising; | |
| if (nego & (ADVERTISED_1000baseT_Full | | |
| ADVERTISED_1000baseT_Half)) { | |
| ethtool_cmd_speed_set(ecmd, SPEED_1000); | |
| ecmd->duplex = !!(nego & ADVERTISED_1000baseT_Full); | |
| } else if (nego & (ADVERTISED_100baseT_Full | | |
| ADVERTISED_100baseT_Half)) { | |
| ethtool_cmd_speed_set(ecmd, SPEED_100); | |
| ecmd->duplex = !!(nego & ADVERTISED_100baseT_Full); | |
| } else { | |
| ethtool_cmd_speed_set(ecmd, SPEED_10); | |
| ecmd->duplex = !!(nego & ADVERTISED_10baseT_Full); | |
| } | |
| } else { | |
| ecmd->autoneg = AUTONEG_DISABLE; | |
| ethtool_cmd_speed_set(ecmd, | |
| ((bmcr & BMCR_SPEED1000 && | |
| (bmcr & BMCR_SPEED100) == 0) ? | |
| SPEED_1000 : | |
| ((bmcr & BMCR_SPEED100) ? | |
| SPEED_100 : SPEED_10))); | |
| ecmd->duplex = (bmcr & BMCR_FULLDPLX) ? DUPLEX_FULL : DUPLEX_HALF; | |
| } | |
| mii->full_duplex = ecmd->duplex; | |
| /* ignore maxtxpkt, maxrxpkt for now */ | |
| return 0; | |
| } | |
| /** | |
| * mii_ethtool_sset - set settings that are specified in @ecmd | |
| * @mii: MII interface | |
| * @ecmd: requested ethtool_cmd | |
| * | |
| * Returns 0 for success, negative on error. | |
| */ | |
| int mii_ethtool_sset(struct mii_if_info *mii, struct ethtool_cmd *ecmd) | |
| { | |
| struct net_device *dev = mii->dev; | |
| u32 speed = ethtool_cmd_speed(ecmd); | |
| if (speed != SPEED_10 && | |
| speed != SPEED_100 && | |
| speed != SPEED_1000) | |
| return -EINVAL; | |
| if (ecmd->duplex != DUPLEX_HALF && ecmd->duplex != DUPLEX_FULL) | |
| return -EINVAL; | |
| if (ecmd->port != PORT_MII) | |
| return -EINVAL; | |
| if (ecmd->transceiver != XCVR_INTERNAL) | |
| return -EINVAL; | |
| if (ecmd->phy_address != mii->phy_id) | |
| return -EINVAL; | |
| if (ecmd->autoneg != AUTONEG_DISABLE && ecmd->autoneg != AUTONEG_ENABLE) | |
| return -EINVAL; | |
| if ((speed == SPEED_1000) && (!mii->supports_gmii)) | |
| return -EINVAL; | |
| /* ignore supported, maxtxpkt, maxrxpkt */ | |
| if (ecmd->autoneg == AUTONEG_ENABLE) { | |
| u32 bmcr, advert, tmp; | |
| u32 advert2 = 0, tmp2 = 0; | |
| if ((ecmd->advertising & (ADVERTISED_10baseT_Half | | |
| ADVERTISED_10baseT_Full | | |
| ADVERTISED_100baseT_Half | | |
| ADVERTISED_100baseT_Full | | |
| ADVERTISED_1000baseT_Half | | |
| ADVERTISED_1000baseT_Full)) == 0) | |
| return -EINVAL; | |
| /* advertise only what has been requested */ | |
| advert = mii->mdio_read(dev, mii->phy_id, MII_ADVERTISE); | |
| tmp = advert & ~(ADVERTISE_ALL | ADVERTISE_100BASE4); | |
| if (mii->supports_gmii) { | |
| advert2 = mii->mdio_read(dev, mii->phy_id, MII_CTRL1000); | |
| tmp2 = advert2 & ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL); | |
| } | |
| tmp |= ethtool_adv_to_mii_adv_t(ecmd->advertising); | |
| if (mii->supports_gmii) | |
| tmp2 |= | |
| ethtool_adv_to_mii_ctrl1000_t(ecmd->advertising); | |
| if (advert != tmp) { | |
| mii->mdio_write(dev, mii->phy_id, MII_ADVERTISE, tmp); | |
| mii->advertising = tmp; | |
| } | |
| if ((mii->supports_gmii) && (advert2 != tmp2)) | |
| mii->mdio_write(dev, mii->phy_id, MII_CTRL1000, tmp2); | |
| /* turn on autonegotiation, and force a renegotiate */ | |
| bmcr = mii->mdio_read(dev, mii->phy_id, MII_BMCR); | |
| bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART); | |
| mii->mdio_write(dev, mii->phy_id, MII_BMCR, bmcr); | |
| mii->force_media = 0; | |
| } else { | |
| u32 bmcr, tmp; | |
| /* turn off auto negotiation, set speed and duplexity */ | |
| bmcr = mii->mdio_read(dev, mii->phy_id, MII_BMCR); | |
| tmp = bmcr & ~(BMCR_ANENABLE | BMCR_SPEED100 | | |
| BMCR_SPEED1000 | BMCR_FULLDPLX); | |
| if (speed == SPEED_1000) | |
| tmp |= BMCR_SPEED1000; | |
| else if (speed == SPEED_100) | |
| tmp |= BMCR_SPEED100; | |
| if (ecmd->duplex == DUPLEX_FULL) { | |
| tmp |= BMCR_FULLDPLX; | |
| mii->full_duplex = 1; | |
| } else | |
| mii->full_duplex = 0; | |
| if (bmcr != tmp) | |
| mii->mdio_write(dev, mii->phy_id, MII_BMCR, tmp); | |
| mii->force_media = 1; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * mii_check_gmii_support - check if the MII supports Gb interfaces | |
| * @mii: the MII interface | |
| */ | |
| int mii_check_gmii_support(struct mii_if_info *mii) | |
| { | |
| int reg; | |
| reg = mii->mdio_read(mii->dev, mii->phy_id, MII_BMSR); | |
| if (reg & BMSR_ESTATEN) { | |
| reg = mii->mdio_read(mii->dev, mii->phy_id, MII_ESTATUS); | |
| if (reg & (ESTATUS_1000_TFULL | ESTATUS_1000_THALF)) | |
| return 1; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * mii_link_ok - is link status up/ok | |
| * @mii: the MII interface | |
| * | |
| * Returns 1 if the MII reports link status up/ok, 0 otherwise. | |
| */ | |
| int mii_link_ok (struct mii_if_info *mii) | |
| { | |
| /* first, a dummy read, needed to latch some MII phys */ | |
| mii->mdio_read(mii->dev, mii->phy_id, MII_BMSR); | |
| if (mii->mdio_read(mii->dev, mii->phy_id, MII_BMSR) & BMSR_LSTATUS) | |
| return 1; | |
| return 0; | |
| } | |
| /** | |
| * mii_nway_restart - restart NWay (autonegotiation) for this interface | |
| * @mii: the MII interface | |
| * | |
| * Returns 0 on success, negative on error. | |
| */ | |
| int mii_nway_restart (struct mii_if_info *mii) | |
| { | |
| int bmcr; | |
| int r = -EINVAL; | |
| /* if autoneg is off, it's an error */ | |
| bmcr = mii->mdio_read(mii->dev, mii->phy_id, MII_BMCR); | |
| if (bmcr & BMCR_ANENABLE) { | |
| bmcr |= BMCR_ANRESTART; | |
| mii->mdio_write(mii->dev, mii->phy_id, MII_BMCR, bmcr); | |
| r = 0; | |
| } | |
| return r; | |
| } | |
| /** | |
| * mii_check_link - check MII link status | |
| * @mii: MII interface | |
| * | |
| * If the link status changed (previous != current), call | |
| * netif_carrier_on() if current link status is Up or call | |
| * netif_carrier_off() if current link status is Down. | |
| */ | |
| void mii_check_link (struct mii_if_info *mii) | |
| { | |
| int cur_link = mii_link_ok(mii); | |
| int prev_link = netif_carrier_ok(mii->dev); | |
| if (cur_link && !prev_link) | |
| netif_carrier_on(mii->dev); | |
| else if (prev_link && !cur_link) | |
| netif_carrier_off(mii->dev); | |
| } | |
| /** | |
| * mii_check_media - check the MII interface for a duplex change | |
| * @mii: the MII interface | |
| * @ok_to_print: OK to print link up/down messages | |
| * @init_media: OK to save duplex mode in @mii | |
| * | |
| * Returns 1 if the duplex mode changed, 0 if not. | |
| * If the media type is forced, always returns 0. | |
| */ | |
| unsigned int mii_check_media (struct mii_if_info *mii, | |
| unsigned int ok_to_print, | |
| unsigned int init_media) | |
| { | |
| unsigned int old_carrier, new_carrier; | |
| int advertise, lpa, media, duplex; | |
| int lpa2 = 0; | |
| /* if forced media, go no further */ | |
| if (mii->force_media) | |
| return 0; /* duplex did not change */ | |
| /* check current and old link status */ | |
| old_carrier = netif_carrier_ok(mii->dev) ? 1 : 0; | |
| new_carrier = (unsigned int) mii_link_ok(mii); | |
| /* if carrier state did not change, this is a "bounce", | |
| * just exit as everything is already set correctly | |
| */ | |
| if ((!init_media) && (old_carrier == new_carrier)) | |
| return 0; /* duplex did not change */ | |
| /* no carrier, nothing much to do */ | |
| if (!new_carrier) { | |
| netif_carrier_off(mii->dev); | |
| if (ok_to_print) | |
| netdev_info(mii->dev, "link down\n"); | |
| return 0; /* duplex did not change */ | |
| } | |
| /* | |
| * we have carrier, see who's on the other end | |
| */ | |
| netif_carrier_on(mii->dev); | |
| /* get MII advertise and LPA values */ | |
| if ((!init_media) && (mii->advertising)) | |
| advertise = mii->advertising; | |
| else { | |
| advertise = mii->mdio_read(mii->dev, mii->phy_id, MII_ADVERTISE); | |
| mii->advertising = advertise; | |
| } | |
| lpa = mii->mdio_read(mii->dev, mii->phy_id, MII_LPA); | |
| if (mii->supports_gmii) | |
| lpa2 = mii->mdio_read(mii->dev, mii->phy_id, MII_STAT1000); | |
| /* figure out media and duplex from advertise and LPA values */ | |
| media = mii_nway_result(lpa & advertise); | |
| duplex = (media & ADVERTISE_FULL) ? 1 : 0; | |
| if (lpa2 & LPA_1000FULL) | |
| duplex = 1; | |
| if (ok_to_print) | |
| netdev_info(mii->dev, "link up, %uMbps, %s-duplex, lpa 0x%04X\n", | |
| lpa2 & (LPA_1000FULL | LPA_1000HALF) ? 1000 : | |
| media & (ADVERTISE_100FULL | ADVERTISE_100HALF) ? | |
| 100 : 10, | |
| duplex ? "full" : "half", | |
| lpa); | |
| if ((init_media) || (mii->full_duplex != duplex)) { | |
| mii->full_duplex = duplex; | |
| return 1; /* duplex changed */ | |
| } | |
| return 0; /* duplex did not change */ | |
| } | |
| /** | |
| * generic_mii_ioctl - main MII ioctl interface | |
| * @mii_if: the MII interface | |
| * @mii_data: MII ioctl data structure | |
| * @cmd: MII ioctl command | |
| * @duplex_chg_out: pointer to @duplex_changed status if there was no | |
| * ioctl error | |
| * | |
| * Returns 0 on success, negative on error. | |
| */ | |
| int generic_mii_ioctl(struct mii_if_info *mii_if, | |
| struct mii_ioctl_data *mii_data, int cmd, | |
| unsigned int *duplex_chg_out) | |
| { | |
| int rc = 0; | |
| unsigned int duplex_changed = 0; | |
| if (duplex_chg_out) | |
| *duplex_chg_out = 0; | |
| mii_data->phy_id &= mii_if->phy_id_mask; | |
| mii_data->reg_num &= mii_if->reg_num_mask; | |
| switch(cmd) { | |
| case SIOCGMIIPHY: | |
| mii_data->phy_id = mii_if->phy_id; | |
| /* fall through */ | |
| case SIOCGMIIREG: | |
| mii_data->val_out = | |
| mii_if->mdio_read(mii_if->dev, mii_data->phy_id, | |
| mii_data->reg_num); | |
| break; | |
| case SIOCSMIIREG: { | |
| u16 val = mii_data->val_in; | |
| if (mii_data->phy_id == mii_if->phy_id) { | |
| switch(mii_data->reg_num) { | |
| case MII_BMCR: { | |
| unsigned int new_duplex = 0; | |
| if (val & (BMCR_RESET|BMCR_ANENABLE)) | |
| mii_if->force_media = 0; | |
| else | |
| mii_if->force_media = 1; | |
| if (mii_if->force_media && | |
| (val & BMCR_FULLDPLX)) | |
| new_duplex = 1; | |
| if (mii_if->full_duplex != new_duplex) { | |
| duplex_changed = 1; | |
| mii_if->full_duplex = new_duplex; | |
| } | |
| break; | |
| } | |
| case MII_ADVERTISE: | |
| mii_if->advertising = val; | |
| break; | |
| default: | |
| /* do nothing */ | |
| break; | |
| } | |
| } | |
| mii_if->mdio_write(mii_if->dev, mii_data->phy_id, | |
| mii_data->reg_num, val); | |
| break; | |
| } | |
| default: | |
| rc = -EOPNOTSUPP; | |
| break; | |
| } | |
| if ((rc == 0) && (duplex_chg_out) && (duplex_changed)) | |
| *duplex_chg_out = 1; | |
| return rc; | |
| } | |
| MODULE_AUTHOR ("Jeff Garzik <jgarzik@pobox.com>"); | |
| MODULE_DESCRIPTION ("MII hardware support library"); | |
| MODULE_LICENSE("GPL"); | |
| EXPORT_SYMBOL(mii_link_ok); | |
| EXPORT_SYMBOL(mii_nway_restart); | |
| EXPORT_SYMBOL(mii_ethtool_gset); | |
| EXPORT_SYMBOL(mii_ethtool_sset); | |
| EXPORT_SYMBOL(mii_check_link); | |
| EXPORT_SYMBOL(mii_check_media); | |
| EXPORT_SYMBOL(mii_check_gmii_support); | |
| EXPORT_SYMBOL(generic_mii_ioctl); | |