blob: 290e60383baf4f6a23862996b8c5ecb38d33a2b0 [file] [log] [blame]
/*
* usb_a9263.dts - Device Tree file for Caloa USB A9293 board
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2 only
*/
/dts-v1/;
#include "at91sam9263.dtsi"
/ {
model = "Calao USB A9263";
compatible = "atmel,usb-a9263", "atmel,at91sam9263", "atmel,at91sam9";
chosen {
bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
};
memory {
reg = <0x20000000 0x4000000>;
};
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
main_clock: clock@0 {
compatible = "atmel,osc", "fixed-clock";
clock-frequency = <12000000>;
};
};
ahb {
apb {
dbgu: serial@ffffee00 {
status = "okay";
};
macb0: ethernet@fffbc000 {
phy-mode = "rmii";
status = "okay";
};
usb1: gadget@fff78000 {
atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>;
status = "okay";
};
spi0: spi@fffa4000 {
cs-gpios = <&pioB 15 GPIO_ACTIVE_HIGH>;
status = "okay";
mtd_dataflash@0 {
compatible = "atmel,at45", "atmel,dataflash";
reg = <0>;
spi-max-frequency = <15000000>;
};
};
shdwc@fffffd10 {
atmel,wakeup-counter = <10>;
atmel,wakeup-rtt-timer;
};
};
nand0: nand@40000000 {
nand-bus-width = <8>;
nand-ecc-mode = "soft";
nand-on-flash-bbt;
status = "okay";
at91bootstrap@0 {
label = "at91bootstrap";
reg = <0x0 0x20000>;
};
barebox@20000 {
label = "barebox";
reg = <0x20000 0x40000>;
};
bareboxenv@60000 {
label = "bareboxenv";
reg = <0x60000 0x20000>;
};
bareboxenv2@80000 {
label = "bareboxenv2";
reg = <0x80000 0x20000>;
};
oftree@80000 {
label = "oftree";
reg = <0xa0000 0x20000>;
};
kernel@a0000 {
label = "kernel";
reg = <0xc0000 0x400000>;
};
rootfs@4a0000 {
label = "rootfs";
reg = <0x4c0000 0x7800000>;
};
data@7ca0000 {
label = "data";
reg = <0x7cc0000 0x8340000>;
};
};
usb0: ohci@00a00000 {
num-ports = <2>;
status = "okay";
};
};
leds {
compatible = "gpio-leds";
user_led {
label = "user_led";
gpios = <&pioB 21 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
user_pb {
label = "user_pb";
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
linux,code = <28>;
gpio-key,wakeup;
};
};
i2c@0 {
status = "okay";
};
};