| /* |
| * Simple synchronous serial port driver for ETRAX FS. |
| * |
| * Copyright (c) 2005 Axis Communications AB |
| * |
| * Author: Mikael Starvik |
| * |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/types.h> |
| #include <linux/errno.h> |
| #include <linux/major.h> |
| #include <linux/sched.h> |
| #include <linux/slab.h> |
| #include <linux/interrupt.h> |
| #include <linux/poll.h> |
| #include <linux/init.h> |
| #include <linux/timer.h> |
| #include <linux/spinlock.h> |
| |
| #include <asm/io.h> |
| #include <asm/arch/dma.h> |
| #include <asm/arch/pinmux.h> |
| #include <asm/arch/hwregs/reg_rdwr.h> |
| #include <asm/arch/hwregs/sser_defs.h> |
| #include <asm/arch/hwregs/dma_defs.h> |
| #include <asm/arch/hwregs/dma.h> |
| #include <asm/arch/hwregs/intr_vect_defs.h> |
| #include <asm/arch/hwregs/intr_vect.h> |
| #include <asm/arch/hwregs/reg_map.h> |
| #include <asm/sync_serial.h> |
| |
| /* The receiver is a bit tricky beacuse of the continuous stream of data.*/ |
| /* */ |
| /* Three DMA descriptors are linked together. Each DMA descriptor is */ |
| /* responsible for port->bufchunk of a common buffer. */ |
| /* */ |
| /* +---------------------------------------------+ */ |
| /* | +----------+ +----------+ +----------+ | */ |
| /* +-> | Descr[0] |-->| Descr[1] |-->| Descr[2] |-+ */ |
| /* +----------+ +----------+ +----------+ */ |
| /* | | | */ |
| /* v v v */ |
| /* +-------------------------------------+ */ |
| /* | BUFFER | */ |
| /* +-------------------------------------+ */ |
| /* |<- data_avail ->| */ |
| /* readp writep */ |
| /* */ |
| /* If the application keeps up the pace readp will be right after writep.*/ |
| /* If the application can't keep the pace we have to throw away data. */ |
| /* The idea is that readp should be ready with the data pointed out by */ |
| /* Descr[i] when the DMA has filled in Descr[i+1]. */ |
| /* Otherwise we will discard */ |
| /* the rest of the data pointed out by Descr1 and set readp to the start */ |
| /* of Descr2 */ |
| |
| #define SYNC_SERIAL_MAJOR 125 |
| |
| /* IN_BUFFER_SIZE should be a multiple of 6 to make sure that 24 bit */ |
| /* words can be handled */ |
| #define IN_BUFFER_SIZE 12288 |
| #define IN_DESCR_SIZE 256 |
| #define NUM_IN_DESCR (IN_BUFFER_SIZE/IN_DESCR_SIZE) |
| #define OUT_BUFFER_SIZE 4096 |
| |
| #define DEFAULT_FRAME_RATE 0 |
| #define DEFAULT_WORD_RATE 7 |
| |
| /* NOTE: Enabling some debug will likely cause overrun or underrun, |
| * especially if manual mode is use. |
| */ |
| #define DEBUG(x) |
| #define DEBUGREAD(x) |
| #define DEBUGWRITE(x) |
| #define DEBUGPOLL(x) |
| #define DEBUGRXINT(x) |
| #define DEBUGTXINT(x) |
| |
| typedef struct sync_port |
| { |
| reg_scope_instances regi_sser; |
| reg_scope_instances regi_dmain; |
| reg_scope_instances regi_dmaout; |
| |
| char started; /* 1 if port has been started */ |
| char port_nbr; /* Port 0 or 1 */ |
| char busy; /* 1 if port is busy */ |
| |
| char enabled; /* 1 if port is enabled */ |
| char use_dma; /* 1 if port uses dma */ |
| char tr_running; |
| |
| char init_irqs; |
| int output; |
| int input; |
| |
| volatile unsigned int out_count; /* Remaining bytes for current transfer */ |
| unsigned char* outp; /* Current position in out_buffer */ |
| volatile unsigned char* volatile readp; /* Next byte to be read by application */ |
| volatile unsigned char* volatile writep; /* Next byte to be written by etrax */ |
| unsigned int in_buffer_size; |
| unsigned int inbufchunk; |
| unsigned char out_buffer[OUT_BUFFER_SIZE] __attribute__ ((aligned(32))); |
| unsigned char in_buffer[IN_BUFFER_SIZE]__attribute__ ((aligned(32))); |
| unsigned char flip[IN_BUFFER_SIZE] __attribute__ ((aligned(32))); |
| struct dma_descr_data* next_rx_desc; |
| struct dma_descr_data* prev_rx_desc; |
| int full; |
| |
| dma_descr_data in_descr[NUM_IN_DESCR] __attribute__ ((__aligned__(16))); |
| dma_descr_context in_context __attribute__ ((__aligned__(32))); |
| dma_descr_data out_descr __attribute__ ((__aligned__(16))); |
| dma_descr_context out_context __attribute__ ((__aligned__(32))); |
| wait_queue_head_t out_wait_q; |
| wait_queue_head_t in_wait_q; |
| |
| spinlock_t lock; |
| } sync_port; |
| |
| static int etrax_sync_serial_init(void); |
| static void initialize_port(int portnbr); |
| static inline int sync_data_avail(struct sync_port *port); |
| |
| static int sync_serial_open(struct inode *, struct file*); |
| static int sync_serial_release(struct inode*, struct file*); |
| static unsigned int sync_serial_poll(struct file *filp, poll_table *wait); |
| |
| static int sync_serial_ioctl(struct inode*, struct file*, |
| unsigned int cmd, unsigned long arg); |
| static ssize_t sync_serial_write(struct file * file, const char * buf, |
| size_t count, loff_t *ppos); |
| static ssize_t sync_serial_read(struct file *file, char *buf, |
| size_t count, loff_t *ppos); |
| |
| #if (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) && \ |
| defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA)) || \ |
| (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) && \ |
| defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA)) |
| #define SYNC_SER_DMA |
| #endif |
| |
| static void send_word(sync_port* port); |
| static void start_dma(struct sync_port *port, const char* data, int count); |
| static void start_dma_in(sync_port* port); |
| #ifdef SYNC_SER_DMA |
| static irqreturn_t tr_interrupt(int irq, void *dev_id, struct pt_regs * regs); |
| static irqreturn_t rx_interrupt(int irq, void *dev_id, struct pt_regs * regs); |
| #endif |
| |
| #if (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) && \ |
| !defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA)) || \ |
| (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) && \ |
| !defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA)) |
| #define SYNC_SER_MANUAL |
| #endif |
| #ifdef SYNC_SER_MANUAL |
| static irqreturn_t manual_interrupt(int irq, void *dev_id, struct pt_regs * regs); |
| #endif |
| |
| /* The ports */ |
| static struct sync_port ports[]= |
| { |
| { |
| .regi_sser = regi_sser0, |
| .regi_dmaout = regi_dma4, |
| .regi_dmain = regi_dma5, |
| #if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA) |
| .use_dma = 1, |
| #else |
| .use_dma = 0, |
| #endif |
| }, |
| { |
| .regi_sser = regi_sser1, |
| .regi_dmaout = regi_dma6, |
| .regi_dmain = regi_dma7, |
| #if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA) |
| .use_dma = 1, |
| #else |
| .use_dma = 0, |
| #endif |
| } |
| }; |
| |
| #define NUMBER_OF_PORTS (sizeof(ports)/sizeof(sync_port)) |
| |
| static const struct file_operations sync_serial_fops = { |
| .owner = THIS_MODULE, |
| .write = sync_serial_write, |
| .read = sync_serial_read, |
| .poll = sync_serial_poll, |
| .ioctl = sync_serial_ioctl, |
| .open = sync_serial_open, |
| .release = sync_serial_release |
| }; |
| |
| static int __init etrax_sync_serial_init(void) |
| { |
| ports[0].enabled = 0; |
| ports[1].enabled = 0; |
| |
| if (register_chrdev(SYNC_SERIAL_MAJOR,"sync serial", &sync_serial_fops) <0 ) |
| { |
| printk("unable to get major for synchronous serial port\n"); |
| return -EBUSY; |
| } |
| |
| /* Initialize Ports */ |
| #if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) |
| if (crisv32_pinmux_alloc_fixed(pinmux_sser0)) |
| { |
| printk("Unable to allocate pins for syncrhronous serial port 0\n"); |
| return -EIO; |
| } |
| ports[0].enabled = 1; |
| initialize_port(0); |
| #endif |
| |
| #if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) |
| if (crisv32_pinmux_alloc_fixed(pinmux_sser1)) |
| { |
| printk("Unable to allocate pins for syncrhronous serial port 0\n"); |
| return -EIO; |
| } |
| ports[1].enabled = 1; |
| initialize_port(1); |
| #endif |
| |
| printk("ETRAX FS synchronous serial port driver\n"); |
| return 0; |
| } |
| |
| static void __init initialize_port(int portnbr) |
| { |
| struct sync_port* port = &ports[portnbr]; |
| reg_sser_rw_cfg cfg = {0}; |
| reg_sser_rw_frm_cfg frm_cfg = {0}; |
| reg_sser_rw_tr_cfg tr_cfg = {0}; |
| reg_sser_rw_rec_cfg rec_cfg = {0}; |
| |
| DEBUG(printk("Init sync serial port %d\n", portnbr)); |
| |
| port->port_nbr = portnbr; |
| port->init_irqs = 1; |
| |
| port->outp = port->out_buffer; |
| port->output = 1; |
| port->input = 0; |
| |
| port->readp = port->flip; |
| port->writep = port->flip; |
| port->in_buffer_size = IN_BUFFER_SIZE; |
| port->inbufchunk = IN_DESCR_SIZE; |
| port->next_rx_desc = &port->in_descr[0]; |
| port->prev_rx_desc = &port->in_descr[NUM_IN_DESCR-1]; |
| port->prev_rx_desc->eol = 1; |
| |
| init_waitqueue_head(&port->out_wait_q); |
| init_waitqueue_head(&port->in_wait_q); |
| |
| spin_lock_init(&port->lock); |
| |
| cfg.out_clk_src = regk_sser_intern_clk; |
| cfg.out_clk_pol = regk_sser_pos; |
| cfg.clk_od_mode = regk_sser_no; |
| cfg.clk_dir = regk_sser_out; |
| cfg.gate_clk = regk_sser_no; |
| cfg.base_freq = regk_sser_f29_493; |
| cfg.clk_div = 256; |
| REG_WR(sser, port->regi_sser, rw_cfg, cfg); |
| |
| frm_cfg.wordrate = DEFAULT_WORD_RATE; |
| frm_cfg.type = regk_sser_edge; |
| frm_cfg.frame_pin_dir = regk_sser_out; |
| frm_cfg.frame_pin_use = regk_sser_frm; |
| frm_cfg.status_pin_dir = regk_sser_in; |
| frm_cfg.status_pin_use = regk_sser_hold; |
| frm_cfg.out_on = regk_sser_tr; |
| frm_cfg.tr_delay = 1; |
| REG_WR(sser, port->regi_sser, rw_frm_cfg, frm_cfg); |
| |
| tr_cfg.urun_stop = regk_sser_no; |
| tr_cfg.sample_size = 7; |
| tr_cfg.sh_dir = regk_sser_msbfirst; |
| tr_cfg.use_dma = port->use_dma ? regk_sser_yes : regk_sser_no; |
| tr_cfg.rate_ctrl = regk_sser_bulk; |
| tr_cfg.data_pin_use = regk_sser_dout; |
| tr_cfg.bulk_wspace = 1; |
| REG_WR(sser, port->regi_sser, rw_tr_cfg, tr_cfg); |
| |
| rec_cfg.sample_size = 7; |
| rec_cfg.sh_dir = regk_sser_msbfirst; |
| rec_cfg.use_dma = port->use_dma ? regk_sser_yes : regk_sser_no; |
| rec_cfg.fifo_thr = regk_sser_inf; |
| REG_WR(sser, port->regi_sser, rw_rec_cfg, rec_cfg); |
| } |
| |
| static inline int sync_data_avail(struct sync_port *port) |
| { |
| int avail; |
| unsigned char *start; |
| unsigned char *end; |
| |
| start = (unsigned char*)port->readp; /* cast away volatile */ |
| end = (unsigned char*)port->writep; /* cast away volatile */ |
| /* 0123456789 0123456789 |
| * ----- - ----- |
| * ^rp ^wp ^wp ^rp |
| */ |
| |
| if (end >= start) |
| avail = end - start; |
| else |
| avail = port->in_buffer_size - (start - end); |
| return avail; |
| } |
| |
| static inline int sync_data_avail_to_end(struct sync_port *port) |
| { |
| int avail; |
| unsigned char *start; |
| unsigned char *end; |
| |
| start = (unsigned char*)port->readp; /* cast away volatile */ |
| end = (unsigned char*)port->writep; /* cast away volatile */ |
| /* 0123456789 0123456789 |
| * ----- ----- |
| * ^rp ^wp ^wp ^rp |
| */ |
| |
| if (end >= start) |
| avail = end - start; |
| else |
| avail = port->flip + port->in_buffer_size - start; |
| return avail; |
| } |
| |
| static int sync_serial_open(struct inode *inode, struct file *file) |
| { |
| int dev = iminor(inode); |
| sync_port* port; |
| reg_dma_rw_cfg cfg = {.en = regk_dma_yes}; |
| reg_dma_rw_intr_mask intr_mask = {.data = regk_dma_yes}; |
| |
| DEBUG(printk("Open sync serial port %d\n", dev)); |
| |
| if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) |
| { |
| DEBUG(printk("Invalid minor %d\n", dev)); |
| return -ENODEV; |
| } |
| port = &ports[dev]; |
| /* Allow open this device twice (assuming one reader and one writer) */ |
| if (port->busy == 2) |
| { |
| DEBUG(printk("Device is busy.. \n")); |
| return -EBUSY; |
| } |
| if (port->init_irqs) { |
| if (port->use_dma) { |
| if (port == &ports[0]){ |
| #ifdef SYNC_SER_DMA |
| if(request_irq(DMA4_INTR_VECT, |
| tr_interrupt, |
| 0, |
| "synchronous serial 0 dma tr", |
| &ports[0])) { |
| printk(KERN_CRIT "Can't allocate sync serial port 0 IRQ"); |
| return -EBUSY; |
| } else if(request_irq(DMA5_INTR_VECT, |
| rx_interrupt, |
| 0, |
| "synchronous serial 1 dma rx", |
| &ports[0])) { |
| free_irq(DMA4_INTR_VECT, &port[0]); |
| printk(KERN_CRIT "Can't allocate sync serial port 0 IRQ"); |
| return -EBUSY; |
| } else if (crisv32_request_dma(SYNC_SER0_TX_DMA_NBR, |
| "synchronous serial 0 dma tr", |
| DMA_VERBOSE_ON_ERROR, |
| 0, |
| dma_sser0)) { |
| free_irq(DMA4_INTR_VECT, &port[0]); |
| free_irq(DMA5_INTR_VECT, &port[0]); |
| printk(KERN_CRIT "Can't allocate sync serial port 0 TX DMA channel"); |
| return -EBUSY; |
| } else if (crisv32_request_dma(SYNC_SER0_RX_DMA_NBR, |
| "synchronous serial 0 dma rec", |
| DMA_VERBOSE_ON_ERROR, |
| 0, |
| dma_sser0)) { |
| crisv32_free_dma(SYNC_SER0_TX_DMA_NBR); |
| free_irq(DMA4_INTR_VECT, &port[0]); |
| free_irq(DMA5_INTR_VECT, &port[0]); |
| printk(KERN_CRIT "Can't allocate sync serial port 1 RX DMA channel"); |
| return -EBUSY; |
| } |
| #endif |
| } |
| else if (port == &ports[1]){ |
| #ifdef SYNC_SER_DMA |
| if (request_irq(DMA6_INTR_VECT, |
| tr_interrupt, |
| 0, |
| "synchronous serial 1 dma tr", |
| &ports[1])) { |
| printk(KERN_CRIT "Can't allocate sync serial port 1 IRQ"); |
| return -EBUSY; |
| } else if (request_irq(DMA7_INTR_VECT, |
| rx_interrupt, |
| 0, |
| "synchronous serial 1 dma rx", |
| &ports[1])) { |
| free_irq(DMA6_INTR_VECT, &ports[1]); |
| printk(KERN_CRIT "Can't allocate sync serial port 3 IRQ"); |
| return -EBUSY; |
| } else if (crisv32_request_dma(SYNC_SER1_TX_DMA_NBR, |
| "synchronous serial 1 dma tr", |
| DMA_VERBOSE_ON_ERROR, |
| 0, |
| dma_sser1)) { |
| free_irq(21, &ports[1]); |
| free_irq(20, &ports[1]); |
| printk(KERN_CRIT "Can't allocate sync serial port 3 TX DMA channel"); |
| return -EBUSY; |
| } else if (crisv32_request_dma(SYNC_SER1_RX_DMA_NBR, |
| "synchronous serial 3 dma rec", |
| DMA_VERBOSE_ON_ERROR, |
| 0, |
| dma_sser1)) { |
| crisv32_free_dma(SYNC_SER1_TX_DMA_NBR); |
| free_irq(DMA6_INTR_VECT, &ports[1]); |
| free_irq(DMA7_INTR_VECT, &ports[1]); |
| printk(KERN_CRIT "Can't allocate sync serial port 3 RX DMA channel"); |
| return -EBUSY; |
| } |
| #endif |
| } |
| |
| /* Enable DMAs */ |
| REG_WR(dma, port->regi_dmain, rw_cfg, cfg); |
| REG_WR(dma, port->regi_dmaout, rw_cfg, cfg); |
| /* Enable DMA IRQs */ |
| REG_WR(dma, port->regi_dmain, rw_intr_mask, intr_mask); |
| REG_WR(dma, port->regi_dmaout, rw_intr_mask, intr_mask); |
| /* Set up wordsize = 2 for DMAs. */ |
| DMA_WR_CMD (port->regi_dmain, regk_dma_set_w_size1); |
| DMA_WR_CMD (port->regi_dmaout, regk_dma_set_w_size1); |
| |
| start_dma_in(port); |
| port->init_irqs = 0; |
| } else { /* !port->use_dma */ |
| #ifdef SYNC_SER_MANUAL |
| if (port == &ports[0]) { |
| if (request_irq(SSER0_INTR_VECT, |
| manual_interrupt, |
| 0, |
| "synchronous serial manual irq", |
| &ports[0])) { |
| printk("Can't allocate sync serial manual irq"); |
| return -EBUSY; |
| } |
| } else if (port == &ports[1]) { |
| if (request_irq(SSER1_INTR_VECT, |
| manual_interrupt, |
| 0, |
| "synchronous serial manual irq", |
| &ports[1])) { |
| printk(KERN_CRIT "Can't allocate sync serial manual irq"); |
| return -EBUSY; |
| } |
| } |
| port->init_irqs = 0; |
| #else |
| panic("sync_serial: Manual mode not supported.\n"); |
| #endif /* SYNC_SER_MANUAL */ |
| } |
| } /* port->init_irqs */ |
| |
| port->busy++; |
| return 0; |
| } |
| |
| static int sync_serial_release(struct inode *inode, struct file *file) |
| { |
| int dev = iminor(inode); |
| sync_port* port; |
| |
| if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) |
| { |
| DEBUG(printk("Invalid minor %d\n", dev)); |
| return -ENODEV; |
| } |
| port = &ports[dev]; |
| if (port->busy) |
| port->busy--; |
| if (!port->busy) |
| /* XXX */ ; |
| return 0; |
| } |
| |
| static unsigned int sync_serial_poll(struct file *file, poll_table *wait) |
| { |
| int dev = iminor(file->f_path.dentry->d_inode); |
| unsigned int mask = 0; |
| sync_port* port; |
| DEBUGPOLL( static unsigned int prev_mask = 0; ); |
| |
| port = &ports[dev]; |
| poll_wait(file, &port->out_wait_q, wait); |
| poll_wait(file, &port->in_wait_q, wait); |
| /* Some room to write */ |
| if (port->out_count < OUT_BUFFER_SIZE) |
| mask |= POLLOUT | POLLWRNORM; |
| /* At least an inbufchunk of data */ |
| if (sync_data_avail(port) >= port->inbufchunk) |
| mask |= POLLIN | POLLRDNORM; |
| |
| DEBUGPOLL(if (mask != prev_mask) |
| printk("sync_serial_poll: mask 0x%08X %s %s\n", mask, |
| mask&POLLOUT?"POLLOUT":"", mask&POLLIN?"POLLIN":""); |
| prev_mask = mask; |
| ); |
| return mask; |
| } |
| |
| static int sync_serial_ioctl(struct inode *inode, struct file *file, |
| unsigned int cmd, unsigned long arg) |
| { |
| int return_val = 0; |
| int dev = iminor(file->f_path.dentry->d_inode); |
| sync_port* port; |
| reg_sser_rw_tr_cfg tr_cfg; |
| reg_sser_rw_rec_cfg rec_cfg; |
| reg_sser_rw_frm_cfg frm_cfg; |
| reg_sser_rw_cfg gen_cfg; |
| reg_sser_rw_intr_mask intr_mask; |
| |
| if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) |
| { |
| DEBUG(printk("Invalid minor %d\n", dev)); |
| return -1; |
| } |
| port = &ports[dev]; |
| spin_lock_irq(&port->lock); |
| |
| tr_cfg = REG_RD(sser, port->regi_sser, rw_tr_cfg); |
| rec_cfg = REG_RD(sser, port->regi_sser, rw_rec_cfg); |
| frm_cfg = REG_RD(sser, port->regi_sser, rw_frm_cfg); |
| gen_cfg = REG_RD(sser, port->regi_sser, rw_cfg); |
| intr_mask = REG_RD(sser, port->regi_sser, rw_intr_mask); |
| |
| switch(cmd) |
| { |
| case SSP_SPEED: |
| if (GET_SPEED(arg) == CODEC) |
| { |
| gen_cfg.base_freq = regk_sser_f32; |
| /* FREQ = 0 => 4 MHz => clk_div = 7*/ |
| gen_cfg.clk_div = 6 + (1 << GET_FREQ(arg)); |
| } |
| else |
| { |
| gen_cfg.base_freq = regk_sser_f29_493; |
| switch (GET_SPEED(arg)) |
| { |
| case SSP150: |
| gen_cfg.clk_div = 29493000 / (150 * 8) - 1; |
| break; |
| case SSP300: |
| gen_cfg.clk_div = 29493000 / (300 * 8) - 1; |
| break; |
| case SSP600: |
| gen_cfg.clk_div = 29493000 / (600 * 8) - 1; |
| break; |
| case SSP1200: |
| gen_cfg.clk_div = 29493000 / (1200 * 8) - 1; |
| break; |
| case SSP2400: |
| gen_cfg.clk_div = 29493000 / (2400 * 8) - 1; |
| break; |
| case SSP4800: |
| gen_cfg.clk_div = 29493000 / (4800 * 8) - 1; |
| break; |
| case SSP9600: |
| gen_cfg.clk_div = 29493000 / (9600 * 8) - 1; |
| break; |
| case SSP19200: |
| gen_cfg.clk_div = 29493000 / (19200 * 8) - 1; |
| break; |
| case SSP28800: |
| gen_cfg.clk_div = 29493000 / (28800 * 8) - 1; |
| break; |
| case SSP57600: |
| gen_cfg.clk_div = 29493000 / (57600 * 8) - 1; |
| break; |
| case SSP115200: |
| gen_cfg.clk_div = 29493000 / (115200 * 8) - 1; |
| break; |
| case SSP230400: |
| gen_cfg.clk_div = 29493000 / (230400 * 8) - 1; |
| break; |
| case SSP460800: |
| gen_cfg.clk_div = 29493000 / (460800 * 8) - 1; |
| break; |
| case SSP921600: |
| gen_cfg.clk_div = 29493000 / (921600 * 8) - 1; |
| break; |
| case SSP3125000: |
| gen_cfg.base_freq = regk_sser_f100; |
| gen_cfg.clk_div = 100000000 / (3125000 * 8) - 1; |
| break; |
| |
| } |
| } |
| frm_cfg.wordrate = GET_WORD_RATE(arg); |
| |
| break; |
| case SSP_MODE: |
| switch(arg) |
| { |
| case MASTER_OUTPUT: |
| port->output = 1; |
| port->input = 0; |
| gen_cfg.clk_dir = regk_sser_out; |
| break; |
| case SLAVE_OUTPUT: |
| port->output = 1; |
| port->input = 0; |
| gen_cfg.clk_dir = regk_sser_in; |
| break; |
| case MASTER_INPUT: |
| port->output = 0; |
| port->input = 1; |
| gen_cfg.clk_dir = regk_sser_out; |
| break; |
| case SLAVE_INPUT: |
| port->output = 0; |
| port->input = 1; |
| gen_cfg.clk_dir = regk_sser_in; |
| break; |
| case MASTER_BIDIR: |
| port->output = 1; |
| port->input = 1; |
| gen_cfg.clk_dir = regk_sser_out; |
| break; |
| case SLAVE_BIDIR: |
| port->output = 1; |
| port->input = 1; |
| gen_cfg.clk_dir = regk_sser_in; |
| break; |
| default: |
| spin_unlock_irq(&port->lock); |
| return -EINVAL; |
| |
| } |
| if (!port->use_dma || (arg == MASTER_OUTPUT || arg == SLAVE_OUTPUT)) |
| intr_mask.rdav = regk_sser_yes; |
| break; |
| case SSP_FRAME_SYNC: |
| if (arg & NORMAL_SYNC) |
| frm_cfg.tr_delay = 1; |
| else if (arg & EARLY_SYNC) |
| frm_cfg.tr_delay = 0; |
| |
| tr_cfg.bulk_wspace = frm_cfg.tr_delay; |
| frm_cfg.early_wend = regk_sser_yes; |
| if (arg & BIT_SYNC) |
| frm_cfg.type = regk_sser_edge; |
| else if (arg & WORD_SYNC) |
| frm_cfg.type = regk_sser_level; |
| else if (arg & EXTENDED_SYNC) |
| frm_cfg.early_wend = regk_sser_no; |
| |
| if (arg & SYNC_ON) |
| frm_cfg.frame_pin_use = regk_sser_frm; |
| else if (arg & SYNC_OFF) |
| frm_cfg.frame_pin_use = regk_sser_gio0; |
| |
| if (arg & WORD_SIZE_8) |
| rec_cfg.sample_size = tr_cfg.sample_size = 7; |
| else if (arg & WORD_SIZE_12) |
| rec_cfg.sample_size = tr_cfg.sample_size = 11; |
| else if (arg & WORD_SIZE_16) |
| rec_cfg.sample_size = tr_cfg.sample_size = 15; |
| else if (arg & WORD_SIZE_24) |
| rec_cfg.sample_size = tr_cfg.sample_size = 23; |
| else if (arg & WORD_SIZE_32) |
| rec_cfg.sample_size = tr_cfg.sample_size = 31; |
| |
| if (arg & BIT_ORDER_MSB) |
| rec_cfg.sh_dir = tr_cfg.sh_dir = regk_sser_msbfirst; |
| else if (arg & BIT_ORDER_LSB) |
| rec_cfg.sh_dir = tr_cfg.sh_dir = regk_sser_lsbfirst; |
| |
| if (arg & FLOW_CONTROL_ENABLE) |
| rec_cfg.fifo_thr = regk_sser_thr16; |
| else if (arg & FLOW_CONTROL_DISABLE) |
| rec_cfg.fifo_thr = regk_sser_inf; |
| |
| if (arg & CLOCK_NOT_GATED) |
| gen_cfg.gate_clk = regk_sser_no; |
| else if (arg & CLOCK_GATED) |
| gen_cfg.gate_clk = regk_sser_yes; |
| |
| break; |
| case SSP_IPOLARITY: |
| /* NOTE!! negedge is considered NORMAL */ |
| if (arg & CLOCK_NORMAL) |
| rec_cfg.clk_pol = regk_sser_neg; |
| else if (arg & CLOCK_INVERT) |
| rec_cfg.clk_pol = regk_sser_pos; |
| |
| if (arg & FRAME_NORMAL) |
| frm_cfg.level = regk_sser_pos_hi; |
| else if (arg & FRAME_INVERT) |
| frm_cfg.level = regk_sser_neg_lo; |
| |
| if (arg & STATUS_NORMAL) |
| gen_cfg.hold_pol = regk_sser_pos; |
| else if (arg & STATUS_INVERT) |
| gen_cfg.hold_pol = regk_sser_neg; |
| break; |
| case SSP_OPOLARITY: |
| if (arg & CLOCK_NORMAL) |
| gen_cfg.out_clk_pol = regk_sser_neg; |
| else if (arg & CLOCK_INVERT) |
| gen_cfg.out_clk_pol = regk_sser_pos; |
| |
| if (arg & FRAME_NORMAL) |
| frm_cfg.level = regk_sser_pos_hi; |
| else if (arg & FRAME_INVERT) |
| frm_cfg.level = regk_sser_neg_lo; |
| |
| if (arg & STATUS_NORMAL) |
| gen_cfg.hold_pol = regk_sser_pos; |
| else if (arg & STATUS_INVERT) |
| gen_cfg.hold_pol = regk_sser_neg; |
| break; |
| case SSP_SPI: |
| rec_cfg.fifo_thr = regk_sser_inf; |
| rec_cfg.sh_dir = tr_cfg.sh_dir = regk_sser_msbfirst; |
| rec_cfg.sample_size = tr_cfg.sample_size = 7; |
| frm_cfg.frame_pin_use = regk_sser_frm; |
| frm_cfg.type = regk_sser_level; |
| frm_cfg.tr_delay = 1; |
| frm_cfg.level = regk_sser_neg_lo; |
| if (arg & SPI_SLAVE) |
| { |
| rec_cfg.clk_pol = regk_sser_neg; |
| gen_cfg.clk_dir = regk_sser_in; |
| port->input = 1; |
| port->output = 0; |
| } |
| else |
| { |
| gen_cfg.out_clk_pol = regk_sser_pos; |
| port->input = 0; |
| port->output = 1; |
| gen_cfg.clk_dir = regk_sser_out; |
| } |
| break; |
| case SSP_INBUFCHUNK: |
| break; |
| default: |
| return_val = -1; |
| } |
| |
| |
| if (port->started) |
| { |
| tr_cfg.tr_en = port->output; |
| rec_cfg.rec_en = port->input; |
| } |
| |
| REG_WR(sser, port->regi_sser, rw_tr_cfg, tr_cfg); |
| REG_WR(sser, port->regi_sser, rw_rec_cfg, rec_cfg); |
| REG_WR(sser, port->regi_sser, rw_frm_cfg, frm_cfg); |
| REG_WR(sser, port->regi_sser, rw_intr_mask, intr_mask); |
| REG_WR(sser, port->regi_sser, rw_cfg, gen_cfg); |
| |
| spin_unlock_irq(&port->lock); |
| return return_val; |
| } |
| |
| static ssize_t sync_serial_write(struct file * file, const char * buf, |
| size_t count, loff_t *ppos) |
| { |
| int dev = iminor(file->f_path.dentry->d_inode); |
| DECLARE_WAITQUEUE(wait, current); |
| sync_port *port; |
| unsigned long c, c1; |
| unsigned long free_outp; |
| unsigned long outp; |
| unsigned long out_buffer; |
| unsigned long flags; |
| |
| if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) |
| { |
| DEBUG(printk("Invalid minor %d\n", dev)); |
| return -ENODEV; |
| } |
| port = &ports[dev]; |
| |
| DEBUGWRITE(printk("W d%d c %lu (%d/%d)\n", port->port_nbr, count, port->out_count, OUT_BUFFER_SIZE)); |
| /* Space to end of buffer */ |
| /* |
| * out_buffer <c1>012345<- c ->OUT_BUFFER_SIZE |
| * outp^ +out_count |
| ^free_outp |
| * out_buffer 45<- c ->0123OUT_BUFFER_SIZE |
| * +out_count outp^ |
| * free_outp |
| * |
| */ |
| |
| /* Read variables that may be updated by interrupts */ |
| spin_lock_irqsave(&port->lock, flags); |
| count = count > OUT_BUFFER_SIZE - port->out_count ? OUT_BUFFER_SIZE - port->out_count : count; |
| outp = (unsigned long)port->outp; |
| free_outp = outp + port->out_count; |
| spin_unlock_irqrestore(&port->lock, flags); |
| out_buffer = (unsigned long)port->out_buffer; |
| |
| /* Find out where and how much to write */ |
| if (free_outp >= out_buffer + OUT_BUFFER_SIZE) |
| free_outp -= OUT_BUFFER_SIZE; |
| if (free_outp >= outp) |
| c = out_buffer + OUT_BUFFER_SIZE - free_outp; |
| else |
| c = outp - free_outp; |
| if (c > count) |
| c = count; |
| |
| // DEBUGWRITE(printk("w op %08lX fop %08lX c %lu\n", outp, free_outp, c)); |
| if (copy_from_user((void*)free_outp, buf, c)) |
| return -EFAULT; |
| |
| if (c != count) { |
| buf += c; |
| c1 = count - c; |
| DEBUGWRITE(printk("w2 fi %lu c %lu c1 %lu\n", free_outp-out_buffer, c, c1)); |
| if (copy_from_user((void*)out_buffer, buf, c1)) |
| return -EFAULT; |
| } |
| spin_lock_irqsave(&port->lock, flags); |
| port->out_count += count; |
| spin_unlock_irqrestore(&port->lock, flags); |
| |
| /* Make sure transmitter/receiver is running */ |
| if (!port->started) |
| { |
| reg_sser_rw_cfg cfg = REG_RD(sser, port->regi_sser, rw_cfg); |
| reg_sser_rw_tr_cfg tr_cfg = REG_RD(sser, port->regi_sser, rw_tr_cfg); |
| reg_sser_rw_rec_cfg rec_cfg = REG_RD(sser, port->regi_sser, rw_rec_cfg); |
| cfg.en = regk_sser_yes; |
| tr_cfg.tr_en = port->output; |
| rec_cfg.rec_en = port->input; |
| REG_WR(sser, port->regi_sser, rw_cfg, cfg); |
| REG_WR(sser, port->regi_sser, rw_tr_cfg, tr_cfg); |
| REG_WR(sser, port->regi_sser, rw_rec_cfg, rec_cfg); |
| port->started = 1; |
| } |
| |
| if (file->f_flags & O_NONBLOCK) { |
| spin_lock_irqsave(&port->lock, flags); |
| if (!port->tr_running) { |
| if (!port->use_dma) { |
| reg_sser_rw_intr_mask intr_mask; |
| intr_mask = REG_RD(sser, port->regi_sser, rw_intr_mask); |
| /* Start sender by writing data */ |
| send_word(port); |
| /* and enable transmitter ready IRQ */ |
| intr_mask.trdy = 1; |
| REG_WR(sser, port->regi_sser, rw_intr_mask, intr_mask); |
| } else { |
| start_dma(port, (unsigned char* volatile )port->outp, c); |
| } |
| } |
| spin_unlock_irqrestore(&port->lock, flags); |
| DEBUGWRITE(printk("w d%d c %lu NB\n", |
| port->port_nbr, count)); |
| return count; |
| } |
| |
| /* Sleep until all sent */ |
| |
| add_wait_queue(&port->out_wait_q, &wait); |
| set_current_state(TASK_INTERRUPTIBLE); |
| spin_lock_irqsave(&port->lock, flags); |
| if (!port->tr_running) { |
| if (!port->use_dma) { |
| reg_sser_rw_intr_mask intr_mask; |
| intr_mask = REG_RD(sser, port->regi_sser, rw_intr_mask); |
| /* Start sender by writing data */ |
| send_word(port); |
| /* and enable transmitter ready IRQ */ |
| intr_mask.trdy = 1; |
| REG_WR(sser, port->regi_sser, rw_intr_mask, intr_mask); |
| } else { |
| start_dma(port, port->outp, c); |
| } |
| } |
| spin_unlock_irqrestore(&port->lock, flags); |
| schedule(); |
| set_current_state(TASK_RUNNING); |
| remove_wait_queue(&port->out_wait_q, &wait); |
| if (signal_pending(current)) |
| { |
| return -EINTR; |
| } |
| DEBUGWRITE(printk("w d%d c %lu\n", port->port_nbr, count)); |
| return count; |
| } |
| |
| static ssize_t sync_serial_read(struct file * file, char * buf, |
| size_t count, loff_t *ppos) |
| { |
| int dev = iminor(file->f_path.dentry->d_inode); |
| int avail; |
| sync_port *port; |
| unsigned char* start; |
| unsigned char* end; |
| unsigned long flags; |
| |
| if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) |
| { |
| DEBUG(printk("Invalid minor %d\n", dev)); |
| return -ENODEV; |
| } |
| port = &ports[dev]; |
| |
| DEBUGREAD(printk("R%d c %d ri %lu wi %lu /%lu\n", dev, count, port->readp - port->flip, port->writep - port->flip, port->in_buffer_size)); |
| |
| if (!port->started) |
| { |
| reg_sser_rw_cfg cfg = REG_RD(sser, port->regi_sser, rw_cfg); |
| reg_sser_rw_tr_cfg tr_cfg = REG_RD(sser, port->regi_sser, rw_tr_cfg); |
| reg_sser_rw_rec_cfg rec_cfg = REG_RD(sser, port->regi_sser, rw_rec_cfg); |
| cfg.en = regk_sser_yes; |
| tr_cfg.tr_en = regk_sser_yes; |
| rec_cfg.rec_en = regk_sser_yes; |
| REG_WR(sser, port->regi_sser, rw_cfg, cfg); |
| REG_WR(sser, port->regi_sser, rw_tr_cfg, tr_cfg); |
| REG_WR(sser, port->regi_sser, rw_rec_cfg, rec_cfg); |
| port->started = 1; |
| } |
| |
| |
| /* Calculate number of available bytes */ |
| /* Save pointers to avoid that they are modified by interrupt */ |
| spin_lock_irqsave(&port->lock, flags); |
| start = (unsigned char*)port->readp; /* cast away volatile */ |
| end = (unsigned char*)port->writep; /* cast away volatile */ |
| spin_unlock_irqrestore(&port->lock, flags); |
| while ((start == end) && !port->full) /* No data */ |
| { |
| if (file->f_flags & O_NONBLOCK) |
| { |
| return -EAGAIN; |
| } |
| |
| interruptible_sleep_on(&port->in_wait_q); |
| if (signal_pending(current)) |
| { |
| return -EINTR; |
| } |
| spin_lock_irqsave(&port->lock, flags); |
| start = (unsigned char*)port->readp; /* cast away volatile */ |
| end = (unsigned char*)port->writep; /* cast away volatile */ |
| spin_unlock_irqrestore(&port->lock, flags); |
| } |
| |
| /* Lazy read, never return wrapped data. */ |
| if (port->full) |
| avail = port->in_buffer_size; |
| else if (end > start) |
| avail = end - start; |
| else |
| avail = port->flip + port->in_buffer_size - start; |
| |
| count = count > avail ? avail : count; |
| if (copy_to_user(buf, start, count)) |
| return -EFAULT; |
| /* Disable interrupts while updating readp */ |
| spin_lock_irqsave(&port->lock, flags); |
| port->readp += count; |
| if (port->readp >= port->flip + port->in_buffer_size) /* Wrap? */ |
| port->readp = port->flip; |
| port->full = 0; |
| spin_unlock_irqrestore(&port->lock, flags); |
| DEBUGREAD(printk("r %d\n", count)); |
| return count; |
| } |
| |
| static void send_word(sync_port* port) |
| { |
| reg_sser_rw_tr_cfg tr_cfg = REG_RD(sser, port->regi_sser, rw_tr_cfg); |
| reg_sser_rw_tr_data tr_data = {0}; |
| |
| switch(tr_cfg.sample_size) |
| { |
| case 8: |
| port->out_count--; |
| tr_data.data = *port->outp++; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| break; |
| case 12: |
| { |
| int data = (*port->outp++) << 8; |
| data |= *port->outp++; |
| port->out_count-=2; |
| tr_data.data = data; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| } |
| break; |
| case 16: |
| port->out_count-=2; |
| tr_data.data = *(unsigned short *)port->outp; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| port->outp+=2; |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| break; |
| case 24: |
| port->out_count-=3; |
| tr_data.data = *(unsigned short *)port->outp; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| port->outp+=2; |
| tr_data.data = *port->outp++; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| break; |
| case 32: |
| port->out_count-=4; |
| tr_data.data = *(unsigned short *)port->outp; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| port->outp+=2; |
| tr_data.data = *(unsigned short *)port->outp; |
| REG_WR(sser, port->regi_sser, rw_tr_data, tr_data); |
| port->outp+=2; |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| break; |
| } |
| } |
| |
| |
| static void start_dma(struct sync_port* port, const char* data, int count) |
| { |
| port->tr_running = 1; |
| port->out_descr.buf = (char*)virt_to_phys((char*)data); |
| port->out_descr.after = port->out_descr.buf + count; |
| port->out_descr.eol = port->out_descr.intr = 1; |
| |
| port->out_context.saved_data = (dma_descr_data*)virt_to_phys(&port->out_descr); |
| port->out_context.saved_data_buf = port->out_descr.buf; |
| |
| DMA_START_CONTEXT(port->regi_dmaout, virt_to_phys((char*)&port->out_context)); |
| DEBUGTXINT(printk("dma %08lX c %d\n", (unsigned long)data, count)); |
| } |
| |
| static void start_dma_in(sync_port* port) |
| { |
| int i; |
| char* buf; |
| port->writep = port->flip; |
| |
| if (port->writep > port->flip + port->in_buffer_size) |
| { |
| panic("Offset too large in sync serial driver\n"); |
| return; |
| } |
| buf = (char*)virt_to_phys(port->in_buffer); |
| for (i = 0; i < NUM_IN_DESCR; i++) { |
| port->in_descr[i].buf = buf; |
| port->in_descr[i].after = buf + port->inbufchunk; |
| port->in_descr[i].intr = 1; |
| port->in_descr[i].next = (dma_descr_data*)virt_to_phys(&port->in_descr[i+1]); |
| port->in_descr[i].buf = buf; |
| buf += port->inbufchunk; |
| } |
| /* Link the last descriptor to the first */ |
| port->in_descr[i-1].next = (dma_descr_data*)virt_to_phys(&port->in_descr[0]); |
| port->in_descr[i-1].eol = regk_sser_yes; |
| port->next_rx_desc = &port->in_descr[0]; |
| port->prev_rx_desc = &port->in_descr[NUM_IN_DESCR - 1]; |
| port->in_context.saved_data = (dma_descr_data*)virt_to_phys(&port->in_descr[0]); |
| port->in_context.saved_data_buf = port->in_descr[0].buf; |
| DMA_START_CONTEXT(port->regi_dmain, virt_to_phys(&port->in_context)); |
| } |
| |
| #ifdef SYNC_SER_DMA |
| static irqreturn_t tr_interrupt(int irq, void *dev_id, struct pt_regs * regs) |
| { |
| reg_dma_r_masked_intr masked; |
| reg_dma_rw_ack_intr ack_intr = {.data = regk_dma_yes}; |
| int i; |
| struct dma_descr_data *descr; |
| unsigned int sentl; |
| int found = 0; |
| |
| for (i = 0; i < NUMBER_OF_PORTS; i++) |
| { |
| sync_port *port = &ports[i]; |
| if (!port->enabled || !port->use_dma ) |
| continue; |
| |
| masked = REG_RD(dma, port->regi_dmaout, r_masked_intr); |
| |
| if (masked.data) /* IRQ active for the port? */ |
| { |
| found = 1; |
| /* Clear IRQ */ |
| REG_WR(dma, port->regi_dmaout, rw_ack_intr, ack_intr); |
| descr = &port->out_descr; |
| sentl = descr->after - descr->buf; |
| port->out_count -= sentl; |
| port->outp += sentl; |
| if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) |
| port->outp = port->out_buffer; |
| if (port->out_count) { |
| int c; |
| c = port->out_buffer + OUT_BUFFER_SIZE - port->outp; |
| if (c > port->out_count) |
| c = port->out_count; |
| DEBUGTXINT(printk("tx_int DMAWRITE %i %i\n", sentl, c)); |
| start_dma(port, port->outp, c); |
| } else { |
| DEBUGTXINT(printk("tx_int DMA stop %i\n", sentl)); |
| port->tr_running = 0; |
| } |
| wake_up_interruptible(&port->out_wait_q); /* wake up the waiting process */ |
| } |
| } |
| return IRQ_RETVAL(found); |
| } /* tr_interrupt */ |
| |
| static irqreturn_t rx_interrupt(int irq, void *dev_id, struct pt_regs * regs) |
| { |
| reg_dma_r_masked_intr masked; |
| reg_dma_rw_ack_intr ack_intr = {.data = regk_dma_yes}; |
| |
| int i; |
| int found = 0; |
| |
| for (i = 0; i < NUMBER_OF_PORTS; i++) |
| { |
| sync_port *port = &ports[i]; |
| |
| if (!port->enabled || !port->use_dma ) |
| continue; |
| |
| masked = REG_RD(dma, port->regi_dmain, r_masked_intr); |
| |
| if (masked.data) /* Descriptor interrupt */ |
| { |
| found = 1; |
| while (REG_RD(dma, port->regi_dmain, rw_data) != |
| virt_to_phys(port->next_rx_desc)) { |
| |
| if (port->writep + port->inbufchunk > port->flip + port->in_buffer_size) { |
| int first_size = port->flip + port->in_buffer_size - port->writep; |
| memcpy((char*)port->writep, phys_to_virt((unsigned)port->next_rx_desc->buf), first_size); |
| memcpy(port->flip, phys_to_virt((unsigned)port->next_rx_desc->buf+first_size), port->inbufchunk - first_size); |
| port->writep = port->flip + port->inbufchunk - first_size; |
| } else { |
| memcpy((char*)port->writep, |
| phys_to_virt((unsigned)port->next_rx_desc->buf), |
| port->inbufchunk); |
| port->writep += port->inbufchunk; |
| if (port->writep >= port->flip + port->in_buffer_size) |
| port->writep = port->flip; |
| } |
| if (port->writep == port->readp) |
| { |
| port->full = 1; |
| } |
| |
| port->next_rx_desc->eol = 0; |
| port->prev_rx_desc->eol = 1; |
| port->prev_rx_desc = phys_to_virt((unsigned)port->next_rx_desc); |
| port->next_rx_desc = phys_to_virt((unsigned)port->next_rx_desc->next); |
| wake_up_interruptible(&port->in_wait_q); /* wake up the waiting process */ |
| DMA_CONTINUE(port->regi_dmain); |
| REG_WR(dma, port->regi_dmain, rw_ack_intr, ack_intr); |
| |
| } |
| } |
| } |
| return IRQ_RETVAL(found); |
| } /* rx_interrupt */ |
| #endif /* SYNC_SER_DMA */ |
| |
| #ifdef SYNC_SER_MANUAL |
| static irqreturn_t manual_interrupt(int irq, void *dev_id, struct pt_regs * regs) |
| { |
| int i; |
| int found = 0; |
| reg_sser_r_masked_intr masked; |
| |
| for (i = 0; i < NUMBER_OF_PORTS; i++) |
| { |
| sync_port* port = &ports[i]; |
| |
| if (!port->enabled || port->use_dma) |
| { |
| continue; |
| } |
| |
| masked = REG_RD(sser, port->regi_sser, r_masked_intr); |
| if (masked.rdav) /* Data received? */ |
| { |
| reg_sser_rw_rec_cfg rec_cfg = REG_RD(sser, port->regi_sser, rw_rec_cfg); |
| reg_sser_r_rec_data data = REG_RD(sser, port->regi_sser, r_rec_data); |
| found = 1; |
| /* Read data */ |
| switch(rec_cfg.sample_size) |
| { |
| case 8: |
| *port->writep++ = data.data & 0xff; |
| break; |
| case 12: |
| *port->writep = (data.data & 0x0ff0) >> 4; |
| *(port->writep + 1) = data.data & 0x0f; |
| port->writep+=2; |
| break; |
| case 16: |
| *(unsigned short*)port->writep = data.data; |
| port->writep+=2; |
| break; |
| case 24: |
| *(unsigned int*)port->writep = data.data; |
| port->writep+=3; |
| break; |
| case 32: |
| *(unsigned int*)port->writep = data.data; |
| port->writep+=4; |
| break; |
| } |
| |
| if (port->writep >= port->flip + port->in_buffer_size) /* Wrap? */ |
| port->writep = port->flip; |
| if (port->writep == port->readp) { |
| /* receive buffer overrun, discard oldest data |
| */ |
| port->readp++; |
| if (port->readp >= port->flip + port->in_buffer_size) /* Wrap? */ |
| port->readp = port->flip; |
| } |
| if (sync_data_avail(port) >= port->inbufchunk) |
| wake_up_interruptible(&port->in_wait_q); /* Wake up application */ |
| } |
| |
| if (masked.trdy) /* Transmitter ready? */ |
| { |
| found = 1; |
| if (port->out_count > 0) /* More data to send */ |
| send_word(port); |
| else /* transmission finished */ |
| { |
| reg_sser_rw_intr_mask intr_mask; |
| intr_mask = REG_RD(sser, port->regi_sser, rw_intr_mask); |
| intr_mask.trdy = 0; |
| REG_WR(sser, port->regi_sser, rw_intr_mask, intr_mask); |
| wake_up_interruptible(&port->out_wait_q); /* Wake up application */ |
| } |
| } |
| } |
| return IRQ_RETVAL(found); |
| } |
| #endif |
| |
| module_init(etrax_sync_serial_init); |