| /*************************************************************************** |
| * * |
| * Copyright 2003 LSI Corporation. All rights reserved. * |
| * * |
| * Description * |
| * ------------ * |
| * This include file contains SAS firmware interface IOC Log Info codes * |
| * * |
| *-------------------------------------------------------------------------* |
| */ |
| |
| #ifndef IOPI_IOCLOGINFO_H_INCLUDED |
| #define IOPI_IOCLOGINFO_H_INCLUDED |
| |
| #define SAS_LOGINFO_NEXUS_LOSS 0x31170000 |
| #define SAS_LOGINFO_MASK 0xFFFF0000 |
| |
| /****************************************************************************/ |
| /* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */ |
| /* Format: */ |
| /* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */ |
| /* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */ |
| /* Bits 23-16: LOGINFO_CODE */ |
| /* Bits 15-0: LOGINFO_CODE Specific */ |
| /****************************************************************************/ |
| |
| /****************************************************************************/ |
| /* IOC_LOGINFO_ORIGINATOR defines */ |
| /****************************************************************************/ |
| #define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000) |
| #define IOC_LOGINFO_ORIGINATOR_PL (0x01000000) |
| #define IOC_LOGINFO_ORIGINATOR_IR (0x02000000) |
| |
| #define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000) |
| |
| /****************************************************************************/ |
| /* LOGINFO_CODE defines */ |
| /****************************************************************************/ |
| #define IOC_LOGINFO_CODE_MASK (0x00FF0000) |
| #define IOC_LOGINFO_CODE_SHIFT (16) |
| |
| /****************************************************************************/ |
| /* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */ |
| /****************************************************************************/ |
| #define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000) |
| #define IOP_LOGINFO_CODE_UNUSED2 (0x00020000) |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000) |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */ |
| #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */ |
| |
| #define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */ |
| #define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */ |
| #define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */ |
| #define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occured while attempting to upload the entire flash */ |
| #define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occured while attempting to upload single flash region */ |
| #define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occured while DMAing FW to host memory */ |
| |
| #define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */ |
| |
| #define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000) |
| |
| #define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */ |
| #define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */ |
| |
| #define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001) |
| #define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002) |
| #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003) |
| #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004) |
| #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005) |
| |
| /****************************************************************************/ |
| /* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */ |
| /****************************************************************************/ |
| #define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */ |
| |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT (0x00000001) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED (0x00000002) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0 (0x00000003) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1 (0x00000004) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0 (0x00000005) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1 (0x00000006) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0 (0x00000007) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1 (0x00000008) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY (0x00000009) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK (0x0000000A) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B (0x0000000B) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E) |
| #define PL_LOGINFO_SUB CODE_OPEN_FAIL_BAD_DEST (0x00000011) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1 (0x00000015) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2 (0x00000016) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3 (0x00000017) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY (0x00000018) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION (0x00000019) |
| |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED (0x0000001B) /* Retry Timeout */ |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED (0x0000001C) /* Retry Timeout */ |
| |
| |
| |
| #define PL_LOGINFO_CODE_INVALID_SGL (0x00020000) |
| #define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000) |
| #define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000) |
| #define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000) |
| #define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000) |
| #define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000) |
| #define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000) |
| #define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000) |
| #define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000) |
| #define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000) |
| #define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000) |
| #define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000) |
| #define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000) |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000) |
| #define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */ |
| #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */ |
| #define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000) |
| #define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */ |
| #define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE)*/ |
| #define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000) |
| #define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000) |
| #define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000) |
| #define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000) |
| #define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000) |
| #define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR (0x00180000) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI (0x00000102) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED (0x00000103) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK (0x00000104) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION (0x00000114) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0 (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */ |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1 (0x00000115) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2 (0x00000116) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3 (0x00000117) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */ |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED (0x0000011B) |
| #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */ |
| |
| #define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120) |
| #define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */ |
| #define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */ |
| |
| |
| #define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200) |
| #define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300) |
| #define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) /* Bits 0-3 encode Transport Status Register (offset 0x08) */ |
| /* Bit 0 is Status Bit 0: FrameXferErr */ |
| /* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ |
| /* Bit 3 is Status Bit 18 WriteDataLengthGTDataLengthErr */ |
| |
| #define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500) |
| #define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600) |
| #define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700) |
| #define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800) |
| #define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900) |
| #define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00) |
| #define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00) |
| #define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00) |
| #define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00) |
| #define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00) |
| #define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01) |
| #define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00) |
| #define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000) |
| |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occured on SMP Read */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occured on SMP Write */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */ |
| #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */ |
| |
| #define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */ |
| #define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */ |
| #define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */ |
| #define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */ |
| #define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */ |
| #define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */ |
| #define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transfering data */ |
| #define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transfering sense data */ |
| #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */ |
| #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */ |
| #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */ |
| #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/ |
| #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */ |
| #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2 (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */ |
| #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3 (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */ |
| |
| |
| /****************************************************************************/ |
| /* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */ |
| /****************************************************************************/ |
| #define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000) |
| #define IR_LOGINFO_CODE_UNUSED2 (0x00020000) |
| |
| /* Amount of information passed down for Create Volume is too large */ |
| #define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001) |
| /* Creation of duplicate volume attempted (Bus/Target ID checked) */ |
| #define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002) |
| /* Creation failed due to maximum number of supported volumes exceeded */ |
| #define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003) |
| /* Creation failed due to DMA error in trying to read from host */ |
| #define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004) |
| /* Creation failed due to invalid volume type passed down */ |
| #define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005) |
| /* Creation failed due to error reading MFG Page 4 */ |
| #define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006) |
| /* Creation failed when trying to create internal structures */ |
| #define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007) |
| |
| /* Activation failed due to trying to activate an already active volume */ |
| #define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010) |
| /* Activation failed due to trying to active unsupported volume type */ |
| #define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011) |
| /* Activation failed due to trying to active too many volumes */ |
| #define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012) |
| /* Activation failed due to Volume ID in use already */ |
| #define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013) |
| /* Activation failed call to activateVolume returned failure */ |
| #define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014) |
| /* Activation failed trying to import the volume */ |
| #define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015) |
| |
| /* Phys Disk failed, too many phys disks */ |
| #define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020) |
| /* Amount of information passed down for Create Pnysdisk is too large */ |
| #define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021) |
| /* Creation failed due to DMA error in trying to read from host */ |
| #define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022) |
| /* Creation failed due to invalid Bus TargetID passed down */ |
| #define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023) |
| /* Creation failed due to error in creating RAID Phys Disk Config Page */ |
| #define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024) |
| |
| |
| /* Compatibility Error : IR Disabled */ |
| #define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030) |
| /* Compatibility Error : Inquiry Comand failed */ |
| #define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031) |
| /* Compatibility Error : Device not direct access device */ |
| #define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032) |
| /* Compatibility Error : Removable device found */ |
| #define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033) |
| /* Compatibility Error : Device SCSI Version not 2 or higher */ |
| #define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034) |
| /* Compatibility Error : SATA device, 48 BIT LBA not supported */ |
| #define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035) |
| /* Compatibility Error : Device does not have 512 byte block sizes */ |
| #define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036) |
| /* Compatibility Error : Volume Type check failed */ |
| #define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037) |
| /* Compatibility Error : Volume Type is unsupported by FW */ |
| #define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038) |
| /* Compatibility Error : Disk drive too small for use in volume */ |
| #define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039) |
| /* Compatibility Error : Phys disk for Create Volume not found */ |
| #define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A) |
| /* Compatibility Error : membership count error, too many or too few disks for volume type */ |
| #define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B) |
| /* Compatibility Error : Disk stripe sizes must be 64KB */ |
| #define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C) |
| /* Compatibility Error : IME size limited to < 2TB */ |
| #define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D) |
| |
| |
| /****************************************************************************/ |
| /* Defines for convenience */ |
| /****************************************************************************/ |
| #define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP) |
| #define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL) |
| #define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR) |
| |
| #endif /* end of file */ |
| |
