| /* |
| * Copyright (c) 2000-2013 LSI Corporation. |
| * |
| * |
| * Name: mpi2_sas.h |
| * Title: MPI Serial Attached SCSI structures and definitions |
| * Creation Date: February 9, 2007 |
| * |
| * mpi2_sas.h Version: 02.00.07 |
| * |
| * NOTE: Names (typedefs, defines, etc.) beginning with an MPI25 or Mpi25 |
| * prefix are for use only on MPI v2.5 products, and must not be used |
| * with MPI v2.0 products. Unless otherwise noted, names beginning with |
| * MPI2 or Mpi2 are for use with both MPI v2.0 and MPI v2.5 products. |
| * |
| * Version History |
| * --------------- |
| * |
| * Date Version Description |
| * -------- -------- ------------------------------------------------------ |
| * 04-30-07 02.00.00 Corresponds to Fusion-MPT MPI Specification Rev A. |
| * 06-26-07 02.00.01 Added Clear All Persistent Operation to SAS IO Unit |
| * Control Request. |
| * 10-02-08 02.00.02 Added Set IOC Parameter Operation to SAS IO Unit Control |
| * Request. |
| * 10-28-09 02.00.03 Changed the type of SGL in MPI2_SATA_PASSTHROUGH_REQUEST |
| * to MPI2_SGE_IO_UNION since it supports chained SGLs. |
| * 05-12-10 02.00.04 Modified some comments. |
| * 08-11-10 02.00.05 Added NCQ operations to SAS IO Unit Control. |
| * 11-18-11 02.00.06 Incorporating additions for MPI v2.5. |
| * 07-10-12 02.00.07 Added MPI2_SATA_PT_SGE_UNION for use in the SATA |
| * Passthrough Request message. |
| * -------------------------------------------------------------------------- |
| */ |
| |
| #ifndef MPI2_SAS_H |
| #define MPI2_SAS_H |
| |
| /* |
| *Values for SASStatus. |
| */ |
| #define MPI2_SASSTATUS_SUCCESS (0x00) |
| #define MPI2_SASSTATUS_UNKNOWN_ERROR (0x01) |
| #define MPI2_SASSTATUS_INVALID_FRAME (0x02) |
| #define MPI2_SASSTATUS_UTC_BAD_DEST (0x03) |
| #define MPI2_SASSTATUS_UTC_BREAK_RECEIVED (0x04) |
| #define MPI2_SASSTATUS_UTC_CONNECT_RATE_NOT_SUPPORTED (0x05) |
| #define MPI2_SASSTATUS_UTC_PORT_LAYER_REQUEST (0x06) |
| #define MPI2_SASSTATUS_UTC_PROTOCOL_NOT_SUPPORTED (0x07) |
| #define MPI2_SASSTATUS_UTC_STP_RESOURCES_BUSY (0x08) |
| #define MPI2_SASSTATUS_UTC_WRONG_DESTINATION (0x09) |
| #define MPI2_SASSTATUS_SHORT_INFORMATION_UNIT (0x0A) |
| #define MPI2_SASSTATUS_LONG_INFORMATION_UNIT (0x0B) |
| #define MPI2_SASSTATUS_XFER_RDY_INCORRECT_WRITE_DATA (0x0C) |
| #define MPI2_SASSTATUS_XFER_RDY_REQUEST_OFFSET_ERROR (0x0D) |
| #define MPI2_SASSTATUS_XFER_RDY_NOT_EXPECTED (0x0E) |
| #define MPI2_SASSTATUS_DATA_INCORRECT_DATA_LENGTH (0x0F) |
| #define MPI2_SASSTATUS_DATA_TOO_MUCH_READ_DATA (0x10) |
| #define MPI2_SASSTATUS_DATA_OFFSET_ERROR (0x11) |
| #define MPI2_SASSTATUS_SDSF_NAK_RECEIVED (0x12) |
| #define MPI2_SASSTATUS_SDSF_CONNECTION_FAILED (0x13) |
| #define MPI2_SASSTATUS_INITIATOR_RESPONSE_TIMEOUT (0x14) |
| |
| /* |
| *Values for the SAS DeviceInfo field used in SAS Device Status Change Event |
| *data and SAS Configuration pages. |
| */ |
| #define MPI2_SAS_DEVICE_INFO_SEP (0x00004000) |
| #define MPI2_SAS_DEVICE_INFO_ATAPI_DEVICE (0x00002000) |
| #define MPI2_SAS_DEVICE_INFO_LSI_DEVICE (0x00001000) |
| #define MPI2_SAS_DEVICE_INFO_DIRECT_ATTACH (0x00000800) |
| #define MPI2_SAS_DEVICE_INFO_SSP_TARGET (0x00000400) |
| #define MPI2_SAS_DEVICE_INFO_STP_TARGET (0x00000200) |
| #define MPI2_SAS_DEVICE_INFO_SMP_TARGET (0x00000100) |
| #define MPI2_SAS_DEVICE_INFO_SATA_DEVICE (0x00000080) |
| #define MPI2_SAS_DEVICE_INFO_SSP_INITIATOR (0x00000040) |
| #define MPI2_SAS_DEVICE_INFO_STP_INITIATOR (0x00000020) |
| #define MPI2_SAS_DEVICE_INFO_SMP_INITIATOR (0x00000010) |
| #define MPI2_SAS_DEVICE_INFO_SATA_HOST (0x00000008) |
| |
| #define MPI2_SAS_DEVICE_INFO_MASK_DEVICE_TYPE (0x00000007) |
| #define MPI2_SAS_DEVICE_INFO_NO_DEVICE (0x00000000) |
| #define MPI2_SAS_DEVICE_INFO_END_DEVICE (0x00000001) |
| #define MPI2_SAS_DEVICE_INFO_EDGE_EXPANDER (0x00000002) |
| #define MPI2_SAS_DEVICE_INFO_FANOUT_EXPANDER (0x00000003) |
| |
| /***************************************************************************** |
| * |
| * SAS Messages |
| * |
| *****************************************************************************/ |
| |
| /**************************************************************************** |
| * SMP Passthrough messages |
| ****************************************************************************/ |
| |
| /*SMP Passthrough Request Message */ |
| typedef struct _MPI2_SMP_PASSTHROUGH_REQUEST { |
| U8 PassthroughFlags; /*0x00 */ |
| U8 PhysicalPort; /*0x01 */ |
| U8 ChainOffset; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 RequestDataLength; /*0x04 */ |
| U8 SGLFlags; /*0x06*//*MPI v2.0 only. Reserved on MPI v2.5*/ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved1; /*0x0A */ |
| U32 Reserved2; /*0x0C */ |
| U64 SASAddress; /*0x10 */ |
| U32 Reserved3; /*0x18 */ |
| U32 Reserved4; /*0x1C */ |
| MPI2_SIMPLE_SGE_UNION SGL;/*0x20 */ |
| } MPI2_SMP_PASSTHROUGH_REQUEST, *PTR_MPI2_SMP_PASSTHROUGH_REQUEST, |
| Mpi2SmpPassthroughRequest_t, *pMpi2SmpPassthroughRequest_t; |
| |
| /*values for PassthroughFlags field */ |
| #define MPI2_SMP_PT_REQ_PT_FLAGS_IMMEDIATE (0x80) |
| |
| /*MPI v2.0: use MPI2_SGLFLAGS_ defines from mpi2.h for the SGLFlags field */ |
| |
| /*SMP Passthrough Reply Message */ |
| typedef struct _MPI2_SMP_PASSTHROUGH_REPLY { |
| U8 PassthroughFlags; /*0x00 */ |
| U8 PhysicalPort; /*0x01 */ |
| U8 MsgLength; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 ResponseDataLength; /*0x04 */ |
| U8 SGLFlags; /*0x06 */ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved1; /*0x0A */ |
| U8 Reserved2; /*0x0C */ |
| U8 SASStatus; /*0x0D */ |
| U16 IOCStatus; /*0x0E */ |
| U32 IOCLogInfo; /*0x10 */ |
| U32 Reserved3; /*0x14 */ |
| U8 ResponseData[4]; /*0x18 */ |
| } MPI2_SMP_PASSTHROUGH_REPLY, *PTR_MPI2_SMP_PASSTHROUGH_REPLY, |
| Mpi2SmpPassthroughReply_t, *pMpi2SmpPassthroughReply_t; |
| |
| /*values for PassthroughFlags field */ |
| #define MPI2_SMP_PT_REPLY_PT_FLAGS_IMMEDIATE (0x80) |
| |
| /*values for SASStatus field are at the top of this file */ |
| |
| /**************************************************************************** |
| * SATA Passthrough messages |
| ****************************************************************************/ |
| |
| typedef union _MPI2_SATA_PT_SGE_UNION { |
| MPI2_SGE_SIMPLE_UNION MpiSimple; /*MPI v2.0 only */ |
| MPI2_SGE_CHAIN_UNION MpiChain; /*MPI v2.0 only */ |
| MPI2_IEEE_SGE_SIMPLE_UNION IeeeSimple; |
| MPI2_IEEE_SGE_CHAIN_UNION IeeeChain; /*MPI v2.0 only */ |
| MPI25_IEEE_SGE_CHAIN64 IeeeChain64; /*MPI v2.5 only */ |
| } MPI2_SATA_PT_SGE_UNION, *PTR_MPI2_SATA_PT_SGE_UNION, |
| Mpi2SataPTSGEUnion_t, *pMpi2SataPTSGEUnion_t; |
| |
| /*SATA Passthrough Request Message */ |
| typedef struct _MPI2_SATA_PASSTHROUGH_REQUEST { |
| U16 DevHandle; /*0x00 */ |
| U8 ChainOffset; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 PassthroughFlags; /*0x04 */ |
| U8 SGLFlags; /*0x06*//*MPI v2.0 only. Reserved on MPI v2.5*/ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved1; /*0x0A */ |
| U32 Reserved2; /*0x0C */ |
| U32 Reserved3; /*0x10 */ |
| U32 Reserved4; /*0x14 */ |
| U32 DataLength; /*0x18 */ |
| U8 CommandFIS[20]; /*0x1C */ |
| MPI2_SATA_PT_SGE_UNION SGL;/*0x30*//*MPI v2.5: IEEE 64 elements only*/ |
| } MPI2_SATA_PASSTHROUGH_REQUEST, *PTR_MPI2_SATA_PASSTHROUGH_REQUEST, |
| Mpi2SataPassthroughRequest_t, |
| *pMpi2SataPassthroughRequest_t; |
| |
| /*values for PassthroughFlags field */ |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_EXECUTE_DIAG (0x0100) |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_DMA (0x0020) |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_PIO (0x0010) |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_UNSPECIFIED_VU (0x0004) |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_WRITE (0x0002) |
| #define MPI2_SATA_PT_REQ_PT_FLAGS_READ (0x0001) |
| |
| /*MPI v2.0: use MPI2_SGLFLAGS_ defines from mpi2.h for the SGLFlags field */ |
| |
| /*SATA Passthrough Reply Message */ |
| typedef struct _MPI2_SATA_PASSTHROUGH_REPLY { |
| U16 DevHandle; /*0x00 */ |
| U8 MsgLength; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 PassthroughFlags; /*0x04 */ |
| U8 SGLFlags; /*0x06 */ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved1; /*0x0A */ |
| U8 Reserved2; /*0x0C */ |
| U8 SASStatus; /*0x0D */ |
| U16 IOCStatus; /*0x0E */ |
| U32 IOCLogInfo; /*0x10 */ |
| U8 StatusFIS[20]; /*0x14 */ |
| U32 StatusControlRegisters; /*0x28 */ |
| U32 TransferCount; /*0x2C */ |
| } MPI2_SATA_PASSTHROUGH_REPLY, *PTR_MPI2_SATA_PASSTHROUGH_REPLY, |
| Mpi2SataPassthroughReply_t, *pMpi2SataPassthroughReply_t; |
| |
| /*values for SASStatus field are at the top of this file */ |
| |
| /**************************************************************************** |
| * SAS IO Unit Control messages |
| ****************************************************************************/ |
| |
| /*SAS IO Unit Control Request Message */ |
| typedef struct _MPI2_SAS_IOUNIT_CONTROL_REQUEST { |
| U8 Operation; /*0x00 */ |
| U8 Reserved1; /*0x01 */ |
| U8 ChainOffset; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 DevHandle; /*0x04 */ |
| U8 IOCParameter; /*0x06 */ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved3; /*0x0A */ |
| U16 Reserved4; /*0x0C */ |
| U8 PhyNum; /*0x0E */ |
| U8 PrimFlags; /*0x0F */ |
| U32 Primitive; /*0x10 */ |
| U8 LookupMethod; /*0x14 */ |
| U8 Reserved5; /*0x15 */ |
| U16 SlotNumber; /*0x16 */ |
| U64 LookupAddress; /*0x18 */ |
| U32 IOCParameterValue; /*0x20 */ |
| U32 Reserved7; /*0x24 */ |
| U32 Reserved8; /*0x28 */ |
| } MPI2_SAS_IOUNIT_CONTROL_REQUEST, |
| *PTR_MPI2_SAS_IOUNIT_CONTROL_REQUEST, |
| Mpi2SasIoUnitControlRequest_t, |
| *pMpi2SasIoUnitControlRequest_t; |
| |
| /*values for the Operation field */ |
| #define MPI2_SAS_OP_CLEAR_ALL_PERSISTENT (0x02) |
| #define MPI2_SAS_OP_PHY_LINK_RESET (0x06) |
| #define MPI2_SAS_OP_PHY_HARD_RESET (0x07) |
| #define MPI2_SAS_OP_PHY_CLEAR_ERROR_LOG (0x08) |
| #define MPI2_SAS_OP_SEND_PRIMITIVE (0x0A) |
| #define MPI2_SAS_OP_FORCE_FULL_DISCOVERY (0x0B) |
| #define MPI2_SAS_OP_TRANSMIT_PORT_SELECT_SIGNAL (0x0C) |
| #define MPI2_SAS_OP_REMOVE_DEVICE (0x0D) |
| #define MPI2_SAS_OP_LOOKUP_MAPPING (0x0E) |
| #define MPI2_SAS_OP_SET_IOC_PARAMETER (0x0F) |
| #define MPI25_SAS_OP_ENABLE_FP_DEVICE (0x10) |
| #define MPI25_SAS_OP_DISABLE_FP_DEVICE (0x11) |
| #define MPI25_SAS_OP_ENABLE_FP_ALL (0x12) |
| #define MPI25_SAS_OP_DISABLE_FP_ALL (0x13) |
| #define MPI2_SAS_OP_DEV_ENABLE_NCQ (0x14) |
| #define MPI2_SAS_OP_DEV_DISABLE_NCQ (0x15) |
| #define MPI2_SAS_OP_PRODUCT_SPECIFIC_MIN (0x80) |
| |
| /*values for the PrimFlags field */ |
| #define MPI2_SAS_PRIMFLAGS_SINGLE (0x08) |
| #define MPI2_SAS_PRIMFLAGS_TRIPLE (0x02) |
| #define MPI2_SAS_PRIMFLAGS_REDUNDANT (0x01) |
| |
| /*values for the LookupMethod field */ |
| #define MPI2_SAS_LOOKUP_METHOD_SAS_ADDRESS (0x01) |
| #define MPI2_SAS_LOOKUP_METHOD_SAS_ENCLOSURE_SLOT (0x02) |
| #define MPI2_SAS_LOOKUP_METHOD_SAS_DEVICE_NAME (0x03) |
| |
| /*SAS IO Unit Control Reply Message */ |
| typedef struct _MPI2_SAS_IOUNIT_CONTROL_REPLY { |
| U8 Operation; /*0x00 */ |
| U8 Reserved1; /*0x01 */ |
| U8 MsgLength; /*0x02 */ |
| U8 Function; /*0x03 */ |
| U16 DevHandle; /*0x04 */ |
| U8 IOCParameter; /*0x06 */ |
| U8 MsgFlags; /*0x07 */ |
| U8 VP_ID; /*0x08 */ |
| U8 VF_ID; /*0x09 */ |
| U16 Reserved3; /*0x0A */ |
| U16 Reserved4; /*0x0C */ |
| U16 IOCStatus; /*0x0E */ |
| U32 IOCLogInfo; /*0x10 */ |
| } MPI2_SAS_IOUNIT_CONTROL_REPLY, |
| *PTR_MPI2_SAS_IOUNIT_CONTROL_REPLY, |
| Mpi2SasIoUnitControlReply_t, *pMpi2SasIoUnitControlReply_t; |
| |
| #endif |
