| /* linux/include/asm-arm/arch-s3c2410/regs-gpio.h |
| * |
| * Copyright (c) 2003,2004 Simtec Electronics <linux@simtec.co.uk> |
| * http://www.simtec.co.uk/products/SWLINUX/ |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * S3C2410 GPIO register definitions |
| */ |
| |
| |
| #ifndef __ASM_ARCH_REGS_GPIO_H |
| #define __ASM_ARCH_REGS_GPIO_H "$Id: gpio.h,v 1.5 2003/05/19 12:51:08 ben Exp $" |
| |
| #define S3C2410_GPIONO(bank,offset) ((bank) + (offset)) |
| |
| #define S3C2410_GPIO_BANKA (32*0) |
| #define S3C2410_GPIO_BANKB (32*1) |
| #define S3C2410_GPIO_BANKC (32*2) |
| #define S3C2410_GPIO_BANKD (32*3) |
| #define S3C2410_GPIO_BANKE (32*4) |
| #define S3C2410_GPIO_BANKF (32*5) |
| #define S3C2410_GPIO_BANKG (32*6) |
| #define S3C2410_GPIO_BANKH (32*7) |
| |
| #ifdef CONFIG_CPU_S3C2400 |
| #define S3C24XX_GPIO_BASE(x) S3C2400_GPIO_BASE(x) |
| #define S3C24XX_MISCCR S3C2400_MISCCR |
| #else |
| #define S3C24XX_GPIO_BASE(x) S3C2410_GPIO_BASE(x) |
| #define S3C24XX_MISCCR S3C24XX_GPIOREG2(0x80) |
| #endif /* CONFIG_CPU_S3C2400 */ |
| |
| |
| /* S3C2400 doesn't have a 1:1 mapping to S3C2410 gpio base pins */ |
| |
| #define S3C2400_BANKNUM(pin) (((pin) & ~31) / 32) |
| #define S3C2400_BASEA2B(pin) ((((pin) & ~31) >> 2)) |
| #define S3C2400_BASEC2H(pin) ((S3C2400_BANKNUM(pin) * 10) + \ |
| (2 * (S3C2400_BANKNUM(pin)-2))) |
| |
| #define S3C2400_GPIO_BASE(pin) (pin < S3C2410_GPIO_BANKC ? \ |
| S3C2400_BASEA2B(pin)+S3C24XX_VA_GPIO : \ |
| S3C2400_BASEC2H(pin)+S3C24XX_VA_GPIO) |
| |
| |
| #define S3C2410_GPIO_BASE(pin) ((((pin) & ~31) >> 1) + S3C24XX_VA_GPIO) |
| #define S3C2410_GPIO_OFFSET(pin) ((pin) & 31) |
| |
| /* general configuration options */ |
| |
| #define S3C2410_GPIO_LEAVE (0xFFFFFFFF) |
| #define S3C2410_GPIO_INPUT (0xFFFFFFF0) /* not available on A */ |
| #define S3C2410_GPIO_OUTPUT (0xFFFFFFF1) |
| #define S3C2410_GPIO_IRQ (0xFFFFFFF2) /* not available for all */ |
| #define S3C2410_GPIO_SFN2 (0xFFFFFFF2) /* bank A => addr/cs/nand */ |
| #define S3C2410_GPIO_SFN3 (0xFFFFFFF3) /* not available on A */ |
| |
| /* register address for the GPIO registers. |
| * S3C24XX_GPIOREG2 is for the second set of registers in the |
| * GPIO which move between s3c2410 and s3c2412 type systems */ |
| |
| #define S3C2410_GPIOREG(x) ((x) + S3C24XX_VA_GPIO) |
| #define S3C24XX_GPIOREG2(x) ((x) + S3C24XX_VA_GPIO2) |
| |
| |
| /* configure GPIO ports A..G */ |
| |
| /* port A - S3C2410: 22bits, zero in bit X makes pin X output |
| * S3C2400: 18bits, zero in bit X makes pin X output |
| * 1 makes port special function, this is default |
| */ |
| #define S3C2410_GPACON S3C2410_GPIOREG(0x00) |
| #define S3C2410_GPADAT S3C2410_GPIOREG(0x04) |
| |
| #define S3C2400_GPACON S3C2410_GPIOREG(0x00) |
| #define S3C2400_GPADAT S3C2410_GPIOREG(0x04) |
| |
| #define S3C2410_GPA0 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 0) |
| #define S3C2410_GPA0_OUT (0<<0) |
| #define S3C2410_GPA0_ADDR0 (1<<0) |
| |
| #define S3C2410_GPA1 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 1) |
| #define S3C2410_GPA1_OUT (0<<1) |
| #define S3C2410_GPA1_ADDR16 (1<<1) |
| |
| #define S3C2410_GPA2 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 2) |
| #define S3C2410_GPA2_OUT (0<<2) |
| #define S3C2410_GPA2_ADDR17 (1<<2) |
| |
| #define S3C2410_GPA3 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 3) |
| #define S3C2410_GPA3_OUT (0<<3) |
| #define S3C2410_GPA3_ADDR18 (1<<3) |
| |
| #define S3C2410_GPA4 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 4) |
| #define S3C2410_GPA4_OUT (0<<4) |
| #define S3C2410_GPA4_ADDR19 (1<<4) |
| |
| #define S3C2410_GPA5 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 5) |
| #define S3C2410_GPA5_OUT (0<<5) |
| #define S3C2410_GPA5_ADDR20 (1<<5) |
| |
| #define S3C2410_GPA6 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 6) |
| #define S3C2410_GPA6_OUT (0<<6) |
| #define S3C2410_GPA6_ADDR21 (1<<6) |
| |
| #define S3C2410_GPA7 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 7) |
| #define S3C2410_GPA7_OUT (0<<7) |
| #define S3C2410_GPA7_ADDR22 (1<<7) |
| |
| #define S3C2410_GPA8 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 8) |
| #define S3C2410_GPA8_OUT (0<<8) |
| #define S3C2410_GPA8_ADDR23 (1<<8) |
| |
| #define S3C2410_GPA9 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 9) |
| #define S3C2410_GPA9_OUT (0<<9) |
| #define S3C2410_GPA9_ADDR24 (1<<9) |
| |
| #define S3C2410_GPA10 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 10) |
| #define S3C2410_GPA10_OUT (0<<10) |
| #define S3C2410_GPA10_ADDR25 (1<<10) |
| #define S3C2400_GPA10_SCKE (1<<10) |
| |
| #define S3C2410_GPA11 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 11) |
| #define S3C2410_GPA11_OUT (0<<11) |
| #define S3C2410_GPA11_ADDR26 (1<<11) |
| #define S3C2400_GPA11_nCAS0 (1<<11) |
| |
| #define S3C2410_GPA12 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 12) |
| #define S3C2410_GPA12_OUT (0<<12) |
| #define S3C2410_GPA12_nGCS1 (1<<12) |
| #define S3C2400_GPA12_nCAS1 (1<<12) |
| |
| #define S3C2410_GPA13 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 13) |
| #define S3C2410_GPA13_OUT (0<<13) |
| #define S3C2410_GPA13_nGCS2 (1<<13) |
| #define S3C2400_GPA13_nGCS1 (1<<13) |
| |
| #define S3C2410_GPA14 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 14) |
| #define S3C2410_GPA14_OUT (0<<14) |
| #define S3C2410_GPA14_nGCS3 (1<<14) |
| #define S3C2400_GPA14_nGCS2 (1<<14) |
| |
| #define S3C2410_GPA15 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 15) |
| #define S3C2410_GPA15_OUT (0<<15) |
| #define S3C2410_GPA15_nGCS4 (1<<15) |
| #define S3C2400_GPA15_nGCS3 (1<<15) |
| |
| #define S3C2410_GPA16 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 16) |
| #define S3C2410_GPA16_OUT (0<<16) |
| #define S3C2410_GPA16_nGCS5 (1<<16) |
| #define S3C2400_GPA16_nGCS4 (1<<16) |
| |
| #define S3C2410_GPA17 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 17) |
| #define S3C2410_GPA17_OUT (0<<17) |
| #define S3C2410_GPA17_CLE (1<<17) |
| #define S3C2400_GPA17_nGCS5 (1<<17) |
| |
| #define S3C2410_GPA18 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 18) |
| #define S3C2410_GPA18_OUT (0<<18) |
| #define S3C2410_GPA18_ALE (1<<18) |
| |
| #define S3C2410_GPA19 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 19) |
| #define S3C2410_GPA19_OUT (0<<19) |
| #define S3C2410_GPA19_nFWE (1<<19) |
| |
| #define S3C2410_GPA20 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 20) |
| #define S3C2410_GPA20_OUT (0<<20) |
| #define S3C2410_GPA20_nFRE (1<<20) |
| |
| #define S3C2410_GPA21 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 21) |
| #define S3C2410_GPA21_OUT (0<<21) |
| #define S3C2410_GPA21_nRSTOUT (1<<21) |
| |
| #define S3C2410_GPA22 S3C2410_GPIONO(S3C2410_GPIO_BANKA, 22) |
| #define S3C2410_GPA22_OUT (0<<22) |
| #define S3C2410_GPA22_nFCE (1<<22) |
| |
| /* 0x08 and 0x0c are reserved on S3C2410 */ |
| |
| /* S3C2410: |
| * GPB is 10 IO pins, each configured by 2 bits each in GPBCON. |
| * 00 = input, 01 = output, 10=special function, 11=reserved |
| |
| * S3C2400: |
| * GPB is 16 IO pins, each configured by 2 bits each in GPBCON. |
| * 00 = input, 01 = output, 10=data, 11=special function |
| |
| * bit 0,1 = pin 0, 2,3= pin 1... |
| * |
| * CPBUP = pull up resistor control, 1=disabled, 0=enabled |
| */ |
| |
| #define S3C2410_GPBCON S3C2410_GPIOREG(0x10) |
| #define S3C2410_GPBDAT S3C2410_GPIOREG(0x14) |
| #define S3C2410_GPBUP S3C2410_GPIOREG(0x18) |
| |
| #define S3C2400_GPBCON S3C2410_GPIOREG(0x08) |
| #define S3C2400_GPBDAT S3C2410_GPIOREG(0x0C) |
| #define S3C2400_GPBUP S3C2410_GPIOREG(0x10) |
| |
| /* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */ |
| |
| #define S3C2410_GPB0 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 0) |
| #define S3C2410_GPB0_INP (0x00 << 0) |
| #define S3C2410_GPB0_OUTP (0x01 << 0) |
| #define S3C2410_GPB0_TOUT0 (0x02 << 0) |
| #define S3C2400_GPB0_DATA16 (0x02 << 0) |
| |
| #define S3C2410_GPB1 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 1) |
| #define S3C2410_GPB1_INP (0x00 << 2) |
| #define S3C2410_GPB1_OUTP (0x01 << 2) |
| #define S3C2410_GPB1_TOUT1 (0x02 << 2) |
| #define S3C2400_GPB1_DATA17 (0x02 << 2) |
| |
| #define S3C2410_GPB2 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 2) |
| #define S3C2410_GPB2_INP (0x00 << 4) |
| #define S3C2410_GPB2_OUTP (0x01 << 4) |
| #define S3C2410_GPB2_TOUT2 (0x02 << 4) |
| #define S3C2400_GPB2_DATA18 (0x02 << 4) |
| #define S3C2400_GPB2_TCLK1 (0x03 << 4) |
| |
| #define S3C2410_GPB3 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 3) |
| #define S3C2410_GPB3_INP (0x00 << 6) |
| #define S3C2410_GPB3_OUTP (0x01 << 6) |
| #define S3C2410_GPB3_TOUT3 (0x02 << 6) |
| #define S3C2400_GPB3_DATA19 (0x02 << 6) |
| #define S3C2400_GPB3_TXD1 (0x03 << 6) |
| |
| #define S3C2410_GPB4 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 4) |
| #define S3C2410_GPB4_INP (0x00 << 8) |
| #define S3C2410_GPB4_OUTP (0x01 << 8) |
| #define S3C2410_GPB4_TCLK0 (0x02 << 8) |
| #define S3C2400_GPB4_DATA20 (0x02 << 8) |
| #define S3C2410_GPB4_MASK (0x03 << 8) |
| #define S3C2400_GPB4_RXD1 (0x03 << 8) |
| #define S3C2400_GPB4_MASK (0x03 << 8) |
| |
| #define S3C2410_GPB5 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 5) |
| #define S3C2410_GPB5_INP (0x00 << 10) |
| #define S3C2410_GPB5_OUTP (0x01 << 10) |
| #define S3C2410_GPB5_nXBACK (0x02 << 10) |
| #define S3C2443_GPB5_XBACK (0x03 << 10) |
| #define S3C2400_GPB5_DATA21 (0x02 << 10) |
| #define S3C2400_GPB5_nCTS1 (0x03 << 10) |
| |
| #define S3C2410_GPB6 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 6) |
| #define S3C2410_GPB6_INP (0x00 << 12) |
| #define S3C2410_GPB6_OUTP (0x01 << 12) |
| #define S3C2410_GPB6_nXBREQ (0x02 << 12) |
| #define S3C2443_GPB6_XBREQ (0x03 << 12) |
| #define S3C2400_GPB6_DATA22 (0x02 << 12) |
| #define S3C2400_GPB6_nRTS1 (0x03 << 12) |
| |
| #define S3C2410_GPB7 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 7) |
| #define S3C2410_GPB7_INP (0x00 << 14) |
| #define S3C2410_GPB7_OUTP (0x01 << 14) |
| #define S3C2410_GPB7_nXDACK1 (0x02 << 14) |
| #define S3C2443_GPB7_XDACK1 (0x03 << 14) |
| #define S3C2400_GPB7_DATA23 (0x02 << 14) |
| |
| #define S3C2410_GPB8 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 8) |
| #define S3C2410_GPB8_INP (0x00 << 16) |
| #define S3C2410_GPB8_OUTP (0x01 << 16) |
| #define S3C2410_GPB8_nXDREQ1 (0x02 << 16) |
| #define S3C2400_GPB8_DATA24 (0x02 << 16) |
| |
| #define S3C2410_GPB9 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 9) |
| #define S3C2410_GPB9_INP (0x00 << 18) |
| #define S3C2410_GPB9_OUTP (0x01 << 18) |
| #define S3C2410_GPB9_nXDACK0 (0x02 << 18) |
| #define S3C2443_GPB9_XDACK0 (0x03 << 18) |
| #define S3C2400_GPB9_DATA25 (0x02 << 18) |
| #define S3C2400_GPB9_I2SSDI (0x03 << 18) |
| |
| #define S3C2410_GPB10 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 10) |
| #define S3C2410_GPB10_INP (0x00 << 20) |
| #define S3C2410_GPB10_OUTP (0x01 << 20) |
| #define S3C2410_GPB10_nXDRE0 (0x02 << 20) |
| #define S3C2443_GPB10_XDREQ0 (0x03 << 20) |
| #define S3C2400_GPB10_DATA26 (0x02 << 20) |
| #define S3C2400_GPB10_nSS (0x03 << 20) |
| |
| #define S3C2400_GPB11 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 11) |
| #define S3C2400_GPB11_INP (0x00 << 22) |
| #define S3C2400_GPB11_OUTP (0x01 << 22) |
| #define S3C2400_GPB11_DATA27 (0x02 << 22) |
| |
| #define S3C2400_GPB12 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 12) |
| #define S3C2400_GPB12_INP (0x00 << 24) |
| #define S3C2400_GPB12_OUTP (0x01 << 24) |
| #define S3C2400_GPB12_DATA28 (0x02 << 24) |
| |
| #define S3C2400_GPB13 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 13) |
| #define S3C2400_GPB13_INP (0x00 << 26) |
| #define S3C2400_GPB13_OUTP (0x01 << 26) |
| #define S3C2400_GPB13_DATA29 (0x02 << 26) |
| |
| #define S3C2400_GPB14 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 14) |
| #define S3C2400_GPB14_INP (0x00 << 28) |
| #define S3C2400_GPB14_OUTP (0x01 << 28) |
| #define S3C2400_GPB14_DATA30 (0x02 << 28) |
| |
| #define S3C2400_GPB15 S3C2410_GPIONO(S3C2410_GPIO_BANKB, 15) |
| #define S3C2400_GPB15_INP (0x00 << 30) |
| #define S3C2400_GPB15_OUTP (0x01 << 30) |
| #define S3C2400_GPB15_DATA31 (0x02 << 30) |
| |
| #define S3C2410_GPB_PUPDIS(x) (1<<(x)) |
| |
| /* Port C consits of 16 GPIO/Special function |
| * |
| * almost identical setup to port b, but the special functions are mostly |
| * to do with the video system's sync/etc. |
| */ |
| |
| #define S3C2410_GPCCON S3C2410_GPIOREG(0x20) |
| #define S3C2410_GPCDAT S3C2410_GPIOREG(0x24) |
| #define S3C2410_GPCUP S3C2410_GPIOREG(0x28) |
| |
| #define S3C2400_GPCCON S3C2410_GPIOREG(0x14) |
| #define S3C2400_GPCDAT S3C2410_GPIOREG(0x18) |
| #define S3C2400_GPCUP S3C2410_GPIOREG(0x1C) |
| |
| #define S3C2410_GPC0 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 0) |
| #define S3C2410_GPC0_INP (0x00 << 0) |
| #define S3C2410_GPC0_OUTP (0x01 << 0) |
| #define S3C2410_GPC0_LEND (0x02 << 0) |
| #define S3C2400_GPC0_VD0 (0x02 << 0) |
| |
| #define S3C2410_GPC1 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 1) |
| #define S3C2410_GPC1_INP (0x00 << 2) |
| #define S3C2410_GPC1_OUTP (0x01 << 2) |
| #define S3C2410_GPC1_VCLK (0x02 << 2) |
| #define S3C2400_GPC1_VD1 (0x02 << 2) |
| |
| #define S3C2410_GPC2 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 2) |
| #define S3C2410_GPC2_INP (0x00 << 4) |
| #define S3C2410_GPC2_OUTP (0x01 << 4) |
| #define S3C2410_GPC2_VLINE (0x02 << 4) |
| #define S3C2400_GPC2_VD2 (0x02 << 4) |
| |
| #define S3C2410_GPC3 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 3) |
| #define S3C2410_GPC3_INP (0x00 << 6) |
| #define S3C2410_GPC3_OUTP (0x01 << 6) |
| #define S3C2410_GPC3_VFRAME (0x02 << 6) |
| #define S3C2400_GPC3_VD3 (0x02 << 6) |
| |
| #define S3C2410_GPC4 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 4) |
| #define S3C2410_GPC4_INP (0x00 << 8) |
| #define S3C2410_GPC4_OUTP (0x01 << 8) |
| #define S3C2410_GPC4_VM (0x02 << 8) |
| #define S3C2400_GPC4_VD4 (0x02 << 8) |
| |
| #define S3C2410_GPC5 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 5) |
| #define S3C2410_GPC5_INP (0x00 << 10) |
| #define S3C2410_GPC5_OUTP (0x01 << 10) |
| #define S3C2410_GPC5_LCDVF0 (0x02 << 10) |
| #define S3C2400_GPC5_VD5 (0x02 << 10) |
| |
| #define S3C2410_GPC6 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 6) |
| #define S3C2410_GPC6_INP (0x00 << 12) |
| #define S3C2410_GPC6_OUTP (0x01 << 12) |
| #define S3C2410_GPC6_LCDVF1 (0x02 << 12) |
| #define S3C2400_GPC6_VD6 (0x02 << 12) |
| |
| #define S3C2410_GPC7 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 7) |
| #define S3C2410_GPC7_INP (0x00 << 14) |
| #define S3C2410_GPC7_OUTP (0x01 << 14) |
| #define S3C2410_GPC7_LCDVF2 (0x02 << 14) |
| #define S3C2400_GPC7_VD7 (0x02 << 14) |
| |
| #define S3C2410_GPC8 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 8) |
| #define S3C2410_GPC8_INP (0x00 << 16) |
| #define S3C2410_GPC8_OUTP (0x01 << 16) |
| #define S3C2410_GPC8_VD0 (0x02 << 16) |
| #define S3C2400_GPC8_VD8 (0x02 << 16) |
| |
| #define S3C2410_GPC9 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 9) |
| #define S3C2410_GPC9_INP (0x00 << 18) |
| #define S3C2410_GPC9_OUTP (0x01 << 18) |
| #define S3C2410_GPC9_VD1 (0x02 << 18) |
| #define S3C2400_GPC9_VD9 (0x02 << 18) |
| |
| #define S3C2410_GPC10 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 10) |
| #define S3C2410_GPC10_INP (0x00 << 20) |
| #define S3C2410_GPC10_OUTP (0x01 << 20) |
| #define S3C2410_GPC10_VD2 (0x02 << 20) |
| #define S3C2400_GPC10_VD10 (0x02 << 20) |
| |
| #define S3C2410_GPC11 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 11) |
| #define S3C2410_GPC11_INP (0x00 << 22) |
| #define S3C2410_GPC11_OUTP (0x01 << 22) |
| #define S3C2410_GPC11_VD3 (0x02 << 22) |
| #define S3C2400_GPC11_VD11 (0x02 << 22) |
| |
| #define S3C2410_GPC12 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 12) |
| #define S3C2410_GPC12_INP (0x00 << 24) |
| #define S3C2410_GPC12_OUTP (0x01 << 24) |
| #define S3C2410_GPC12_VD4 (0x02 << 24) |
| #define S3C2400_GPC12_VD12 (0x02 << 24) |
| |
| #define S3C2410_GPC13 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 13) |
| #define S3C2410_GPC13_INP (0x00 << 26) |
| #define S3C2410_GPC13_OUTP (0x01 << 26) |
| #define S3C2410_GPC13_VD5 (0x02 << 26) |
| #define S3C2400_GPC13_VD13 (0x02 << 26) |
| |
| #define S3C2410_GPC14 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 14) |
| #define S3C2410_GPC14_INP (0x00 << 28) |
| #define S3C2410_GPC14_OUTP (0x01 << 28) |
| #define S3C2410_GPC14_VD6 (0x02 << 28) |
| #define S3C2400_GPC14_VD14 (0x02 << 28) |
| |
| #define S3C2410_GPC15 S3C2410_GPIONO(S3C2410_GPIO_BANKC, 15) |
| #define S3C2410_GPC15_INP (0x00 << 30) |
| #define S3C2410_GPC15_OUTP (0x01 << 30) |
| #define S3C2410_GPC15_VD7 (0x02 << 30) |
| #define S3C2400_GPC15_VD15 (0x02 << 30) |
| |
| #define S3C2410_GPC_PUPDIS(x) (1<<(x)) |
| |
| /* |
| * S3C2410: Port D consists of 16 GPIO/Special function |
| * |
| * almost identical setup to port b, but the special functions are mostly |
| * to do with the video system's data. |
| * |
| * S3C2400: Port D consists of 11 GPIO/Special function |
| * |
| * almost identical setup to port c |
| */ |
| |
| #define S3C2410_GPDCON S3C2410_GPIOREG(0x30) |
| #define S3C2410_GPDDAT S3C2410_GPIOREG(0x34) |
| #define S3C2410_GPDUP S3C2410_GPIOREG(0x38) |
| |
| #define S3C2400_GPDCON S3C2410_GPIOREG(0x20) |
| #define S3C2400_GPDDAT S3C2410_GPIOREG(0x24) |
| #define S3C2400_GPDUP S3C2410_GPIOREG(0x28) |
| |
| #define S3C2410_GPD0 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 0) |
| #define S3C2410_GPD0_INP (0x00 << 0) |
| #define S3C2410_GPD0_OUTP (0x01 << 0) |
| #define S3C2410_GPD0_VD8 (0x02 << 0) |
| #define S3C2400_GPD0_VFRAME (0x02 << 0) |
| #define S3C2442_GPD0_nSPICS1 (0x03 << 0) |
| |
| #define S3C2410_GPD1 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 1) |
| #define S3C2410_GPD1_INP (0x00 << 2) |
| #define S3C2410_GPD1_OUTP (0x01 << 2) |
| #define S3C2410_GPD1_VD9 (0x02 << 2) |
| #define S3C2400_GPD1_VM (0x02 << 2) |
| #define S3C2442_GPD1_SPICLK1 (0x03 << 2) |
| |
| #define S3C2410_GPD2 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 2) |
| #define S3C2410_GPD2_INP (0x00 << 4) |
| #define S3C2410_GPD2_OUTP (0x01 << 4) |
| #define S3C2410_GPD2_VD10 (0x02 << 4) |
| #define S3C2400_GPD2_VLINE (0x02 << 4) |
| |
| #define S3C2410_GPD3 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 3) |
| #define S3C2410_GPD3_INP (0x00 << 6) |
| #define S3C2410_GPD3_OUTP (0x01 << 6) |
| #define S3C2410_GPD3_VD11 (0x02 << 6) |
| #define S3C2400_GPD3_VCLK (0x02 << 6) |
| |
| #define S3C2410_GPD4 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 4) |
| #define S3C2410_GPD4_INP (0x00 << 8) |
| #define S3C2410_GPD4_OUTP (0x01 << 8) |
| #define S3C2410_GPD4_VD12 (0x02 << 8) |
| #define S3C2400_GPD4_LEND (0x02 << 8) |
| |
| #define S3C2410_GPD5 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 5) |
| #define S3C2410_GPD5_INP (0x00 << 10) |
| #define S3C2410_GPD5_OUTP (0x01 << 10) |
| #define S3C2410_GPD5_VD13 (0x02 << 10) |
| #define S3C2400_GPD5_TOUT0 (0x02 << 10) |
| |
| #define S3C2410_GPD6 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 6) |
| #define S3C2410_GPD6_INP (0x00 << 12) |
| #define S3C2410_GPD6_OUTP (0x01 << 12) |
| #define S3C2410_GPD6_VD14 (0x02 << 12) |
| #define S3C2400_GPD6_TOUT1 (0x02 << 12) |
| |
| #define S3C2410_GPD7 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 7) |
| #define S3C2410_GPD7_INP (0x00 << 14) |
| #define S3C2410_GPD7_OUTP (0x01 << 14) |
| #define S3C2410_GPD7_VD15 (0x02 << 14) |
| #define S3C2400_GPD7_TOUT2 (0x02 << 14) |
| |
| #define S3C2410_GPD8 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 8) |
| #define S3C2410_GPD8_INP (0x00 << 16) |
| #define S3C2410_GPD8_OUTP (0x01 << 16) |
| #define S3C2410_GPD8_VD16 (0x02 << 16) |
| #define S3C2400_GPD8_TOUT3 (0x02 << 16) |
| |
| #define S3C2410_GPD9 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 9) |
| #define S3C2410_GPD9_INP (0x00 << 18) |
| #define S3C2410_GPD9_OUTP (0x01 << 18) |
| #define S3C2410_GPD9_VD17 (0x02 << 18) |
| #define S3C2400_GPD9_TCLK0 (0x02 << 18) |
| #define S3C2410_GPD9_MASK (0x03 << 18) |
| |
| #define S3C2410_GPD10 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 10) |
| #define S3C2410_GPD10_INP (0x00 << 20) |
| #define S3C2410_GPD10_OUTP (0x01 << 20) |
| #define S3C2410_GPD10_VD18 (0x02 << 20) |
| #define S3C2400_GPD10_nWAIT (0x02 << 20) |
| |
| #define S3C2410_GPD11 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 11) |
| #define S3C2410_GPD11_INP (0x00 << 22) |
| #define S3C2410_GPD11_OUTP (0x01 << 22) |
| #define S3C2410_GPD11_VD19 (0x02 << 22) |
| |
| #define S3C2410_GPD12 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 12) |
| #define S3C2410_GPD12_INP (0x00 << 24) |
| #define S3C2410_GPD12_OUTP (0x01 << 24) |
| #define S3C2410_GPD12_VD20 (0x02 << 24) |
| |
| #define S3C2410_GPD13 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 13) |
| #define S3C2410_GPD13_INP (0x00 << 26) |
| #define S3C2410_GPD13_OUTP (0x01 << 26) |
| #define S3C2410_GPD13_VD21 (0x02 << 26) |
| |
| #define S3C2410_GPD14 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 14) |
| #define S3C2410_GPD14_INP (0x00 << 28) |
| #define S3C2410_GPD14_OUTP (0x01 << 28) |
| #define S3C2410_GPD14_VD22 (0x02 << 28) |
| |
| #define S3C2410_GPD15 S3C2410_GPIONO(S3C2410_GPIO_BANKD, 15) |
| #define S3C2410_GPD15_INP (0x00 << 30) |
| #define S3C2410_GPD15_OUTP (0x01 << 30) |
| #define S3C2410_GPD15_VD23 (0x02 << 30) |
| |
| #define S3C2410_GPD_PUPDIS(x) (1<<(x)) |
| |
| /* S3C2410: |
| * Port E consists of 16 GPIO/Special function |
| * |
| * again, the same as port B, but dealing with I2S, SDI, and |
| * more miscellaneous functions |
| * |
| * S3C2400: |
| * Port E consists of 12 GPIO/Special function |
| * |
| * GPIO / interrupt inputs |
| */ |
| |
| #define S3C2410_GPECON S3C2410_GPIOREG(0x40) |
| #define S3C2410_GPEDAT S3C2410_GPIOREG(0x44) |
| #define S3C2410_GPEUP S3C2410_GPIOREG(0x48) |
| |
| #define S3C2400_GPECON S3C2410_GPIOREG(0x2C) |
| #define S3C2400_GPEDAT S3C2410_GPIOREG(0x30) |
| #define S3C2400_GPEUP S3C2410_GPIOREG(0x34) |
| |
| #define S3C2410_GPE0 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 0) |
| #define S3C2410_GPE0_INP (0x00 << 0) |
| #define S3C2410_GPE0_OUTP (0x01 << 0) |
| #define S3C2410_GPE0_I2SLRCK (0x02 << 0) |
| #define S3C2443_GPE0_AC_nRESET (0x03 << 0) |
| #define S3C2400_GPE0_EINT0 (0x02 << 0) |
| #define S3C2410_GPE0_MASK (0x03 << 0) |
| |
| #define S3C2410_GPE1 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 1) |
| #define S3C2410_GPE1_INP (0x00 << 2) |
| #define S3C2410_GPE1_OUTP (0x01 << 2) |
| #define S3C2410_GPE1_I2SSCLK (0x02 << 2) |
| #define S3C2443_GPE1_AC_SYNC (0x03 << 2) |
| #define S3C2400_GPE1_EINT1 (0x02 << 2) |
| #define S3C2400_GPE1_nSS (0x03 << 2) |
| #define S3C2410_GPE1_MASK (0x03 << 2) |
| |
| #define S3C2410_GPE2 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 2) |
| #define S3C2410_GPE2_INP (0x00 << 4) |
| #define S3C2410_GPE2_OUTP (0x01 << 4) |
| #define S3C2410_GPE2_CDCLK (0x02 << 4) |
| #define S3C2443_GPE2_AC_BITCLK (0x03 << 4) |
| #define S3C2400_GPE2_EINT2 (0x02 << 4) |
| #define S3C2400_GPE2_I2SSDI (0x03 << 4) |
| |
| #define S3C2410_GPE3 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 3) |
| #define S3C2410_GPE3_INP (0x00 << 6) |
| #define S3C2410_GPE3_OUTP (0x01 << 6) |
| #define S3C2410_GPE3_I2SSDI (0x02 << 6) |
| #define S3C2443_GPE3_AC_SDI (0x03 << 6) |
| #define S3C2400_GPE3_EINT3 (0x02 << 6) |
| #define S3C2400_GPE3_nCTS1 (0x03 << 6) |
| #define S3C2410_GPE3_nSS0 (0x03 << 6) |
| #define S3C2410_GPE3_MASK (0x03 << 6) |
| |
| #define S3C2410_GPE4 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 4) |
| #define S3C2410_GPE4_INP (0x00 << 8) |
| #define S3C2410_GPE4_OUTP (0x01 << 8) |
| #define S3C2410_GPE4_I2SSDO (0x02 << 8) |
| #define S3C2443_GPE4_AC_SDO (0x03 << 8) |
| #define S3C2400_GPE4_EINT4 (0x02 << 8) |
| #define S3C2400_GPE4_nRTS1 (0x03 << 8) |
| #define S3C2410_GPE4_I2SSDI (0x03 << 8) |
| #define S3C2410_GPE4_MASK (0x03 << 8) |
| |
| #define S3C2410_GPE5 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 5) |
| #define S3C2410_GPE5_INP (0x00 << 10) |
| #define S3C2410_GPE5_OUTP (0x01 << 10) |
| #define S3C2410_GPE5_SDCLK (0x02 << 10) |
| #define S3C2443_GPE5_SD1_CLK (0x02 << 10) |
| #define S3C2400_GPE5_EINT5 (0x02 << 10) |
| #define S3C2400_GPE5_TCLK1 (0x03 << 10) |
| |
| #define S3C2410_GPE6 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 6) |
| #define S3C2410_GPE6_INP (0x00 << 12) |
| #define S3C2410_GPE6_OUTP (0x01 << 12) |
| #define S3C2410_GPE6_SDCMD (0x02 << 12) |
| #define S3C2443_GPE6_SD1_CMD (0x02 << 12) |
| #define S3C2443_GPE6_AC_BITCLK (0x03 << 12) |
| #define S3C2400_GPE6_EINT6 (0x02 << 12) |
| |
| #define S3C2410_GPE7 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 7) |
| #define S3C2410_GPE7_INP (0x00 << 14) |
| #define S3C2410_GPE7_OUTP (0x01 << 14) |
| #define S3C2410_GPE7_SDDAT0 (0x02 << 14) |
| #define S3C2443_GPE5_SD1_DAT0 (0x02 << 14) |
| #define S3C2443_GPE7_AC_SDI (0x03 << 14) |
| #define S3C2400_GPE7_EINT7 (0x02 << 14) |
| |
| #define S3C2410_GPE8 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 8) |
| #define S3C2410_GPE8_INP (0x00 << 16) |
| #define S3C2410_GPE8_OUTP (0x01 << 16) |
| #define S3C2410_GPE8_SDDAT1 (0x02 << 16) |
| #define S3C2443_GPE8_SD1_DAT1 (0x02 << 16) |
| #define S3C2443_GPE8_AC_SDO (0x03 << 16) |
| #define S3C2400_GPE8_nXDACK0 (0x02 << 16) |
| |
| #define S3C2410_GPE9 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 9) |
| #define S3C2410_GPE9_INP (0x00 << 18) |
| #define S3C2410_GPE9_OUTP (0x01 << 18) |
| #define S3C2410_GPE9_SDDAT2 (0x02 << 18) |
| #define S3C2443_GPE9_SD1_DAT2 (0x02 << 18) |
| #define S3C2443_GPE9_AC_SYNC (0x03 << 18) |
| #define S3C2400_GPE9_nXDACK1 (0x02 << 18) |
| #define S3C2400_GPE9_nXBACK (0x03 << 18) |
| |
| #define S3C2410_GPE10 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 10) |
| #define S3C2410_GPE10_INP (0x00 << 20) |
| #define S3C2410_GPE10_OUTP (0x01 << 20) |
| #define S3C2410_GPE10_SDDAT3 (0x02 << 20) |
| #define S3C2443_GPE10_SD1_DAT3 (0x02 << 20) |
| #define S3C2443_GPE10_AC_nRESET (0x03 << 20) |
| #define S3C2400_GPE10_nXDREQ0 (0x02 << 20) |
| |
| #define S3C2410_GPE11 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 11) |
| #define S3C2410_GPE11_INP (0x00 << 22) |
| #define S3C2410_GPE11_OUTP (0x01 << 22) |
| #define S3C2410_GPE11_SPIMISO0 (0x02 << 22) |
| #define S3C2400_GPE11_nXDREQ1 (0x02 << 22) |
| #define S3C2400_GPE11_nXBREQ (0x03 << 22) |
| |
| #define S3C2410_GPE12 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 12) |
| #define S3C2410_GPE12_INP (0x00 << 24) |
| #define S3C2410_GPE12_OUTP (0x01 << 24) |
| #define S3C2410_GPE12_SPIMOSI0 (0x02 << 24) |
| |
| #define S3C2410_GPE13 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 13) |
| #define S3C2410_GPE13_INP (0x00 << 26) |
| #define S3C2410_GPE13_OUTP (0x01 << 26) |
| #define S3C2410_GPE13_SPICLK0 (0x02 << 26) |
| |
| #define S3C2410_GPE14 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 14) |
| #define S3C2410_GPE14_INP (0x00 << 28) |
| #define S3C2410_GPE14_OUTP (0x01 << 28) |
| #define S3C2410_GPE14_IICSCL (0x02 << 28) |
| #define S3C2410_GPE14_MASK (0x03 << 28) |
| |
| #define S3C2410_GPE15 S3C2410_GPIONO(S3C2410_GPIO_BANKE, 15) |
| #define S3C2410_GPE15_INP (0x00 << 30) |
| #define S3C2410_GPE15_OUTP (0x01 << 30) |
| #define S3C2410_GPE15_IICSDA (0x02 << 30) |
| #define S3C2410_GPE15_MASK (0x03 << 30) |
| |
| #define S3C2440_GPE0_ACSYNC (0x03 << 0) |
| #define S3C2440_GPE1_ACBITCLK (0x03 << 2) |
| #define S3C2440_GPE2_ACRESET (0x03 << 4) |
| #define S3C2440_GPE3_ACIN (0x03 << 6) |
| #define S3C2440_GPE4_ACOUT (0x03 << 8) |
| |
| #define S3C2410_GPE_PUPDIS(x) (1<<(x)) |
| |
| /* S3C2410: |
| * Port F consists of 8 GPIO/Special function |
| * |
| * GPIO / interrupt inputs |
| * |
| * GPFCON has 2 bits for each of the input pins on port F |
| * 00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 undefined |
| * |
| * pull up works like all other ports. |
| * |
| * S3C2400: |
| * Port F consists of 7 GPIO/Special function |
| * |
| * GPIO/serial/misc pins |
| */ |
| |
| #define S3C2410_GPFCON S3C2410_GPIOREG(0x50) |
| #define S3C2410_GPFDAT S3C2410_GPIOREG(0x54) |
| #define S3C2410_GPFUP S3C2410_GPIOREG(0x58) |
| |
| #define S3C2400_GPFCON S3C2410_GPIOREG(0x38) |
| #define S3C2400_GPFDAT S3C2410_GPIOREG(0x3C) |
| #define S3C2400_GPFUP S3C2410_GPIOREG(0x40) |
| |
| #define S3C2410_GPF0 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 0) |
| #define S3C2410_GPF0_INP (0x00 << 0) |
| #define S3C2410_GPF0_OUTP (0x01 << 0) |
| #define S3C2410_GPF0_EINT0 (0x02 << 0) |
| #define S3C2400_GPF0_RXD0 (0x02 << 0) |
| |
| #define S3C2410_GPF1 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 1) |
| #define S3C2410_GPF1_INP (0x00 << 2) |
| #define S3C2410_GPF1_OUTP (0x01 << 2) |
| #define S3C2410_GPF1_EINT1 (0x02 << 2) |
| #define S3C2400_GPF1_RXD1 (0x02 << 2) |
| #define S3C2400_GPF1_IICSDA (0x03 << 2) |
| |
| #define S3C2410_GPF2 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 2) |
| #define S3C2410_GPF2_INP (0x00 << 4) |
| #define S3C2410_GPF2_OUTP (0x01 << 4) |
| #define S3C2410_GPF2_EINT2 (0x02 << 4) |
| #define S3C2400_GPF2_TXD0 (0x02 << 4) |
| |
| #define S3C2410_GPF3 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 3) |
| #define S3C2410_GPF3_INP (0x00 << 6) |
| #define S3C2410_GPF3_OUTP (0x01 << 6) |
| #define S3C2410_GPF3_EINT3 (0x02 << 6) |
| #define S3C2400_GPF3_TXD1 (0x02 << 6) |
| #define S3C2400_GPF3_IICSCL (0x03 << 6) |
| |
| #define S3C2410_GPF4 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 4) |
| #define S3C2410_GPF4_INP (0x00 << 8) |
| #define S3C2410_GPF4_OUTP (0x01 << 8) |
| #define S3C2410_GPF4_EINT4 (0x02 << 8) |
| #define S3C2400_GPF4_nRTS0 (0x02 << 8) |
| #define S3C2400_GPF4_nXBACK (0x03 << 8) |
| |
| #define S3C2410_GPF5 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 5) |
| #define S3C2410_GPF5_INP (0x00 << 10) |
| #define S3C2410_GPF5_OUTP (0x01 << 10) |
| #define S3C2410_GPF5_EINT5 (0x02 << 10) |
| #define S3C2400_GPF5_nCTS0 (0x02 << 10) |
| #define S3C2400_GPF5_nXBREQ (0x03 << 10) |
| |
| #define S3C2410_GPF6 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 6) |
| #define S3C2410_GPF6_INP (0x00 << 12) |
| #define S3C2410_GPF6_OUTP (0x01 << 12) |
| #define S3C2410_GPF6_EINT6 (0x02 << 12) |
| #define S3C2400_GPF6_CLKOUT (0x02 << 12) |
| |
| #define S3C2410_GPF7 S3C2410_GPIONO(S3C2410_GPIO_BANKF, 7) |
| #define S3C2410_GPF7_INP (0x00 << 14) |
| #define S3C2410_GPF7_OUTP (0x01 << 14) |
| #define S3C2410_GPF7_EINT7 (0x02 << 14) |
| |
| #define S3C2410_GPF_PUPDIS(x) (1<<(x)) |
| |
| /* S3C2410: |
| * Port G consists of 8 GPIO/IRQ/Special function |
| * |
| * GPGCON has 2 bits for each of the input pins on port F |
| * 00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 special func |
| * |
| * pull up works like all other ports. |
| * |
| * S3C2400: |
| * Port G consists of 10 GPIO/Special function |
| */ |
| |
| #define S3C2410_GPGCON S3C2410_GPIOREG(0x60) |
| #define S3C2410_GPGDAT S3C2410_GPIOREG(0x64) |
| #define S3C2410_GPGUP S3C2410_GPIOREG(0x68) |
| |
| #define S3C2400_GPGCON S3C2410_GPIOREG(0x44) |
| #define S3C2400_GPGDAT S3C2410_GPIOREG(0x48) |
| #define S3C2400_GPGUP S3C2410_GPIOREG(0x4C) |
| |
| #define S3C2410_GPG0 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 0) |
| #define S3C2410_GPG0_INP (0x00 << 0) |
| #define S3C2410_GPG0_OUTP (0x01 << 0) |
| #define S3C2410_GPG0_EINT8 (0x02 << 0) |
| #define S3C2400_GPG0_I2SLRCK (0x02 << 0) |
| |
| #define S3C2410_GPG1 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 1) |
| #define S3C2410_GPG1_INP (0x00 << 2) |
| #define S3C2410_GPG1_OUTP (0x01 << 2) |
| #define S3C2410_GPG1_EINT9 (0x02 << 2) |
| #define S3C2400_GPG1_I2SSCLK (0x02 << 2) |
| |
| #define S3C2410_GPG2 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 2) |
| #define S3C2410_GPG2_INP (0x00 << 4) |
| #define S3C2410_GPG2_OUTP (0x01 << 4) |
| #define S3C2410_GPG2_EINT10 (0x02 << 4) |
| #define S3C2400_GPG2_CDCLK (0x02 << 4) |
| |
| #define S3C2410_GPG3 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 3) |
| #define S3C2410_GPG3_INP (0x00 << 6) |
| #define S3C2410_GPG3_OUTP (0x01 << 6) |
| #define S3C2410_GPG3_EINT11 (0x02 << 6) |
| #define S3C2400_GPG3_I2SSDO (0x02 << 6) |
| #define S3C2400_GPG3_I2SSDI (0x03 << 6) |
| |
| #define S3C2410_GPG4 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 4) |
| #define S3C2410_GPG4_INP (0x00 << 8) |
| #define S3C2410_GPG4_OUTP (0x01 << 8) |
| #define S3C2410_GPG4_EINT12 (0x02 << 8) |
| #define S3C2400_GPG4_MMCCLK (0x02 << 8) |
| #define S3C2400_GPG4_I2SSDI (0x03 << 8) |
| #define S3C2410_GPG4_LCDPWREN (0x03 << 8) |
| #define S3C2443_GPG4_LCDPWRDN (0x03 << 8) |
| |
| #define S3C2410_GPG5 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 5) |
| #define S3C2410_GPG5_INP (0x00 << 10) |
| #define S3C2410_GPG5_OUTP (0x01 << 10) |
| #define S3C2410_GPG5_EINT13 (0x02 << 10) |
| #define S3C2400_GPG5_MMCCMD (0x02 << 10) |
| #define S3C2400_GPG5_IICSDA (0x03 << 10) |
| #define S3C2410_GPG5_SPIMISO1 (0x03 << 10) /* not s3c2443 */ |
| |
| #define S3C2410_GPG6 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 6) |
| #define S3C2410_GPG6_INP (0x00 << 12) |
| #define S3C2410_GPG6_OUTP (0x01 << 12) |
| #define S3C2410_GPG6_EINT14 (0x02 << 12) |
| #define S3C2400_GPG6_MMCDAT (0x02 << 12) |
| #define S3C2400_GPG6_IICSCL (0x03 << 12) |
| #define S3C2410_GPG6_SPIMOSI1 (0x03 << 12) |
| |
| #define S3C2410_GPG7 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 7) |
| #define S3C2410_GPG7_INP (0x00 << 14) |
| #define S3C2410_GPG7_OUTP (0x01 << 14) |
| #define S3C2410_GPG7_EINT15 (0x02 << 14) |
| #define S3C2410_GPG7_SPICLK1 (0x03 << 14) |
| #define S3C2400_GPG7_SPIMISO (0x02 << 14) |
| #define S3C2400_GPG7_IICSDA (0x03 << 14) |
| |
| #define S3C2410_GPG8 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 8) |
| #define S3C2410_GPG8_INP (0x00 << 16) |
| #define S3C2410_GPG8_OUTP (0x01 << 16) |
| #define S3C2410_GPG8_EINT16 (0x02 << 16) |
| #define S3C2400_GPG8_SPIMOSI (0x02 << 16) |
| #define S3C2400_GPG8_IICSCL (0x03 << 16) |
| |
| #define S3C2410_GPG9 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 9) |
| #define S3C2410_GPG9_INP (0x00 << 18) |
| #define S3C2410_GPG9_OUTP (0x01 << 18) |
| #define S3C2410_GPG9_EINT17 (0x02 << 18) |
| #define S3C2400_GPG9_SPICLK (0x02 << 18) |
| #define S3C2400_GPG9_MMCCLK (0x03 << 18) |
| |
| #define S3C2410_GPG10 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 10) |
| #define S3C2410_GPG10_INP (0x00 << 20) |
| #define S3C2410_GPG10_OUTP (0x01 << 20) |
| #define S3C2410_GPG10_EINT18 (0x02 << 20) |
| |
| #define S3C2410_GPG11 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 11) |
| #define S3C2410_GPG11_INP (0x00 << 22) |
| #define S3C2410_GPG11_OUTP (0x01 << 22) |
| #define S3C2410_GPG11_EINT19 (0x02 << 22) |
| #define S3C2410_GPG11_TCLK1 (0x03 << 22) |
| #define S3C2443_GPG11_CF_nIREQ (0x03 << 22) |
| |
| #define S3C2410_GPG12 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 12) |
| #define S3C2410_GPG12_INP (0x00 << 24) |
| #define S3C2410_GPG12_OUTP (0x01 << 24) |
| #define S3C2410_GPG12_EINT20 (0x02 << 24) |
| #define S3C2410_GPG12_XMON (0x03 << 24) |
| #define S3C2442_GPG12_nSPICS0 (0x03 << 24) |
| #define S3C2443_GPG12_nINPACK (0x03 << 24) |
| |
| #define S3C2410_GPG13 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 13) |
| #define S3C2410_GPG13_INP (0x00 << 26) |
| #define S3C2410_GPG13_OUTP (0x01 << 26) |
| #define S3C2410_GPG13_EINT21 (0x02 << 26) |
| #define S3C2410_GPG13_nXPON (0x03 << 26) |
| #define S3C2443_GPG13_CF_nREG (0x03 << 26) |
| |
| #define S3C2410_GPG14 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 14) |
| #define S3C2410_GPG14_INP (0x00 << 28) |
| #define S3C2410_GPG14_OUTP (0x01 << 28) |
| #define S3C2410_GPG14_EINT22 (0x02 << 28) |
| #define S3C2410_GPG14_YMON (0x03 << 28) |
| #define S3C2443_GPG14_CF_RESET (0x03 << 28) |
| |
| #define S3C2410_GPG15 S3C2410_GPIONO(S3C2410_GPIO_BANKG, 15) |
| #define S3C2410_GPG15_INP (0x00 << 30) |
| #define S3C2410_GPG15_OUTP (0x01 << 30) |
| #define S3C2410_GPG15_EINT23 (0x02 << 30) |
| #define S3C2410_GPG15_nYPON (0x03 << 30) |
| #define S3C2443_GPG15_CF_PWR (0x03 << 30) |
| |
| #define S3C2410_GPG_PUPDIS(x) (1<<(x)) |
| |
| /* Port H consists of11 GPIO/serial/Misc pins |
| * |
| * GPGCON has 2 bits for each of the input pins on port F |
| * 00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 special func |
| * |
| * pull up works like all other ports. |
| */ |
| |
| #define S3C2410_GPHCON S3C2410_GPIOREG(0x70) |
| #define S3C2410_GPHDAT S3C2410_GPIOREG(0x74) |
| #define S3C2410_GPHUP S3C2410_GPIOREG(0x78) |
| |
| #define S3C2410_GPH0 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 0) |
| #define S3C2410_GPH0_INP (0x00 << 0) |
| #define S3C2410_GPH0_OUTP (0x01 << 0) |
| #define S3C2410_GPH0_nCTS0 (0x02 << 0) |
| |
| #define S3C2410_GPH1 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 1) |
| #define S3C2410_GPH1_INP (0x00 << 2) |
| #define S3C2410_GPH1_OUTP (0x01 << 2) |
| #define S3C2410_GPH1_nRTS0 (0x02 << 2) |
| |
| #define S3C2410_GPH2 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 2) |
| #define S3C2410_GPH2_INP (0x00 << 4) |
| #define S3C2410_GPH2_OUTP (0x01 << 4) |
| #define S3C2410_GPH2_TXD0 (0x02 << 4) |
| |
| #define S3C2410_GPH3 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 3) |
| #define S3C2410_GPH3_INP (0x00 << 6) |
| #define S3C2410_GPH3_OUTP (0x01 << 6) |
| #define S3C2410_GPH3_RXD0 (0x02 << 6) |
| |
| #define S3C2410_GPH4 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 4) |
| #define S3C2410_GPH4_INP (0x00 << 8) |
| #define S3C2410_GPH4_OUTP (0x01 << 8) |
| #define S3C2410_GPH4_TXD1 (0x02 << 8) |
| |
| #define S3C2410_GPH5 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 5) |
| #define S3C2410_GPH5_INP (0x00 << 10) |
| #define S3C2410_GPH5_OUTP (0x01 << 10) |
| #define S3C2410_GPH5_RXD1 (0x02 << 10) |
| |
| #define S3C2410_GPH6 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 6) |
| #define S3C2410_GPH6_INP (0x00 << 12) |
| #define S3C2410_GPH6_OUTP (0x01 << 12) |
| #define S3C2410_GPH6_TXD2 (0x02 << 12) |
| #define S3C2410_GPH6_nRTS1 (0x03 << 12) |
| |
| #define S3C2410_GPH7 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 7) |
| #define S3C2410_GPH7_INP (0x00 << 14) |
| #define S3C2410_GPH7_OUTP (0x01 << 14) |
| #define S3C2410_GPH7_RXD2 (0x02 << 14) |
| #define S3C2410_GPH7_nCTS1 (0x03 << 14) |
| |
| #define S3C2410_GPH8 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 8) |
| #define S3C2410_GPH8_INP (0x00 << 16) |
| #define S3C2410_GPH8_OUTP (0x01 << 16) |
| #define S3C2410_GPH8_UCLK (0x02 << 16) |
| |
| #define S3C2410_GPH9 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 9) |
| #define S3C2410_GPH9_INP (0x00 << 18) |
| #define S3C2410_GPH9_OUTP (0x01 << 18) |
| #define S3C2410_GPH9_CLKOUT0 (0x02 << 18) |
| #define S3C2442_GPH9_nSPICS0 (0x03 << 18) |
| |
| #define S3C2410_GPH10 S3C2410_GPIONO(S3C2410_GPIO_BANKH, 10) |
| #define S3C2410_GPH10_INP (0x00 << 20) |
| #define S3C2410_GPH10_OUTP (0x01 << 20) |
| #define S3C2410_GPH10_CLKOUT1 (0x02 << 20) |
| |
| /* The S3C2412 and S3C2413 move the GPJ register set to after |
| * GPH, which means all registers after 0x80 are now offset by 0x10 |
| * for the 2412/2413 from the 2410/2440/2442 |
| */ |
| |
| /* miscellaneous control */ |
| #define S3C2400_MISCCR S3C2410_GPIOREG(0x54) |
| #define S3C2410_MISCCR S3C2410_GPIOREG(0x80) |
| #define S3C2410_DCLKCON S3C2410_GPIOREG(0x84) |
| |
| #define S3C24XX_DCLKCON S3C24XX_GPIOREG2(0x84) |
| |
| /* see clock.h for dclk definitions */ |
| |
| /* pullup control on databus */ |
| #define S3C2410_MISCCR_SPUCR_HEN (0<<0) |
| #define S3C2410_MISCCR_SPUCR_HDIS (1<<0) |
| #define S3C2410_MISCCR_SPUCR_LEN (0<<1) |
| #define S3C2410_MISCCR_SPUCR_LDIS (1<<1) |
| |
| #define S3C2400_MISCCR_SPUCR_LEN (0<<0) |
| #define S3C2400_MISCCR_SPUCR_LDIS (1<<0) |
| #define S3C2400_MISCCR_SPUCR_HEN (0<<1) |
| #define S3C2400_MISCCR_SPUCR_HDIS (1<<1) |
| |
| #define S3C2400_MISCCR_HZ_STOPEN (0<<2) |
| #define S3C2400_MISCCR_HZ_STOPPREV (1<<2) |
| |
| #define S3C2410_MISCCR_USBDEV (0<<3) |
| #define S3C2410_MISCCR_USBHOST (1<<3) |
| |
| #define S3C2410_MISCCR_CLK0_MPLL (0<<4) |
| #define S3C2410_MISCCR_CLK0_UPLL (1<<4) |
| #define S3C2410_MISCCR_CLK0_FCLK (2<<4) |
| #define S3C2410_MISCCR_CLK0_HCLK (3<<4) |
| #define S3C2410_MISCCR_CLK0_PCLK (4<<4) |
| #define S3C2410_MISCCR_CLK0_DCLK0 (5<<4) |
| #define S3C2410_MISCCR_CLK0_MASK (7<<4) |
| |
| #define S3C2412_MISCCR_CLK0_RTC (2<<4) |
| |
| #define S3C2410_MISCCR_CLK1_MPLL (0<<8) |
| #define S3C2410_MISCCR_CLK1_UPLL (1<<8) |
| #define S3C2410_MISCCR_CLK1_FCLK (2<<8) |
| #define S3C2410_MISCCR_CLK1_HCLK (3<<8) |
| #define S3C2410_MISCCR_CLK1_PCLK (4<<8) |
| #define S3C2410_MISCCR_CLK1_DCLK1 (5<<8) |
| #define S3C2410_MISCCR_CLK1_MASK (7<<8) |
| |
| #define S3C2412_MISCCR_CLK1_CLKsrc (0<<8) |
| |
| #define S3C2410_MISCCR_USBSUSPND0 (1<<12) |
| #define S3C2410_MISCCR_USBSUSPND1 (1<<13) |
| |
| #define S3C2410_MISCCR_nRSTCON (1<<16) |
| |
| #define S3C2410_MISCCR_nEN_SCLK0 (1<<17) |
| #define S3C2410_MISCCR_nEN_SCLK1 (1<<18) |
| #define S3C2410_MISCCR_nEN_SCLKE (1<<19) /* not 2412 */ |
| #define S3C2410_MISCCR_SDSLEEP (7<<17) |
| |
| /* external interrupt control... */ |
| /* S3C2410_EXTINT0 -> irq sense control for EINT0..EINT7 |
| * S3C2410_EXTINT1 -> irq sense control for EINT8..EINT15 |
| * S3C2410_EXTINT2 -> irq sense control for EINT16..EINT23 |
| * |
| * note S3C2410_EXTINT2 has filtering options for EINT16..EINT23 |
| * |
| * Samsung datasheet p9-25 |
| */ |
| #define S3C2400_EXTINT0 S3C2410_GPIOREG(0x58) |
| #define S3C2410_EXTINT0 S3C2410_GPIOREG(0x88) |
| #define S3C2410_EXTINT1 S3C2410_GPIOREG(0x8C) |
| #define S3C2410_EXTINT2 S3C2410_GPIOREG(0x90) |
| |
| #define S3C24XX_EXTINT0 S3C24XX_GPIOREG2(0x88) |
| #define S3C24XX_EXTINT1 S3C24XX_GPIOREG2(0x8C) |
| #define S3C24XX_EXTINT2 S3C24XX_GPIOREG2(0x90) |
| |
| /* values for S3C2410_EXTINT0/1/2 */ |
| #define S3C2410_EXTINT_LOWLEV (0x00) |
| #define S3C2410_EXTINT_HILEV (0x01) |
| #define S3C2410_EXTINT_FALLEDGE (0x02) |
| #define S3C2410_EXTINT_RISEEDGE (0x04) |
| #define S3C2410_EXTINT_BOTHEDGE (0x06) |
| |
| /* interrupt filtering conrrol for EINT16..EINT23 */ |
| #define S3C2410_EINFLT0 S3C2410_GPIOREG(0x94) |
| #define S3C2410_EINFLT1 S3C2410_GPIOREG(0x98) |
| #define S3C2410_EINFLT2 S3C2410_GPIOREG(0x9C) |
| #define S3C2410_EINFLT3 S3C2410_GPIOREG(0xA0) |
| |
| #define S3C24XX_EINFLT0 S3C24XX_GPIOREG2(0x94) |
| #define S3C24XX_EINFLT1 S3C24XX_GPIOREG2(0x98) |
| #define S3C24XX_EINFLT2 S3C24XX_GPIOREG2(0x9C) |
| #define S3C24XX_EINFLT3 S3C24XX_GPIOREG2(0xA0) |
| |
| /* values for interrupt filtering */ |
| #define S3C2410_EINTFLT_PCLK (0x00) |
| #define S3C2410_EINTFLT_EXTCLK (1<<7) |
| #define S3C2410_EINTFLT_WIDTHMSK(x) ((x) & 0x3f) |
| |
| /* removed EINTxxxx defs from here, not meant for this */ |
| |
| /* GSTATUS have miscellaneous information in them |
| * |
| * These move between s3c2410 and s3c2412 style systems. |
| */ |
| |
| #define S3C2410_GSTATUS0 S3C2410_GPIOREG(0x0AC) |
| #define S3C2410_GSTATUS1 S3C2410_GPIOREG(0x0B0) |
| #define S3C2410_GSTATUS2 S3C2410_GPIOREG(0x0B4) |
| #define S3C2410_GSTATUS3 S3C2410_GPIOREG(0x0B8) |
| #define S3C2410_GSTATUS4 S3C2410_GPIOREG(0x0BC) |
| |
| #define S3C2412_GSTATUS0 S3C2410_GPIOREG(0x0BC) |
| #define S3C2412_GSTATUS1 S3C2410_GPIOREG(0x0C0) |
| #define S3C2412_GSTATUS2 S3C2410_GPIOREG(0x0C4) |
| #define S3C2412_GSTATUS3 S3C2410_GPIOREG(0x0C8) |
| #define S3C2412_GSTATUS4 S3C2410_GPIOREG(0x0CC) |
| |
| #define S3C24XX_GSTATUS0 S3C24XX_GPIOREG2(0x0AC) |
| #define S3C24XX_GSTATUS1 S3C24XX_GPIOREG2(0x0B0) |
| #define S3C24XX_GSTATUS2 S3C24XX_GPIOREG2(0x0B4) |
| #define S3C24XX_GSTATUS3 S3C24XX_GPIOREG2(0x0B8) |
| #define S3C24XX_GSTATUS4 S3C24XX_GPIOREG2(0x0BC) |
| |
| #define S3C2410_GSTATUS0_nWAIT (1<<3) |
| #define S3C2410_GSTATUS0_NCON (1<<2) |
| #define S3C2410_GSTATUS0_RnB (1<<1) |
| #define S3C2410_GSTATUS0_nBATTFLT (1<<0) |
| |
| #define S3C2410_GSTATUS1_IDMASK (0xffff0000) |
| #define S3C2410_GSTATUS1_2410 (0x32410000) |
| #define S3C2410_GSTATUS1_2412 (0x32412001) |
| #define S3C2410_GSTATUS1_2440 (0x32440000) |
| #define S3C2410_GSTATUS1_2442 (0x32440aaa) |
| |
| #define S3C2410_GSTATUS2_WTRESET (1<<2) |
| #define S3C2410_GSTATUS2_OFFRESET (1<<1) |
| #define S3C2410_GSTATUS2_PONRESET (1<<0) |
| |
| /* open drain control register */ |
| #define S3C2400_OPENCR S3C2410_GPIOREG(0x50) |
| |
| #define S3C2400_OPENCR_OPC_RXD1DIS (0<<0) |
| #define S3C2400_OPENCR_OPC_RXD1EN (1<<0) |
| #define S3C2400_OPENCR_OPC_TXD1DIS (0<<1) |
| #define S3C2400_OPENCR_OPC_TXD1EN (1<<1) |
| #define S3C2400_OPENCR_OPC_CMDDIS (0<<2) |
| #define S3C2400_OPENCR_OPC_CMDEN (1<<2) |
| #define S3C2400_OPENCR_OPC_DATDIS (0<<3) |
| #define S3C2400_OPENCR_OPC_DATEN (1<<3) |
| #define S3C2400_OPENCR_OPC_MISODIS (0<<4) |
| #define S3C2400_OPENCR_OPC_MISOEN (1<<4) |
| #define S3C2400_OPENCR_OPC_MOSIDIS (0<<5) |
| #define S3C2400_OPENCR_OPC_MOSIEN (1<<5) |
| |
| /* 2412/2413 sleep configuration registers */ |
| |
| #define S3C2412_GPBSLPCON S3C2410_GPIOREG(0x1C) |
| #define S3C2412_GPCSLPCON S3C2410_GPIOREG(0x2C) |
| #define S3C2412_GPDSLPCON S3C2410_GPIOREG(0x3C) |
| #define S3C2412_GPFSLPCON S3C2410_GPIOREG(0x5C) |
| #define S3C2412_GPGSLPCON S3C2410_GPIOREG(0x6C) |
| #define S3C2412_GPHSLPCON S3C2410_GPIOREG(0x7C) |
| |
| /* definitions for each pin bit */ |
| #define S3C2412_GPIO_SLPCON_LOW ( 0x00 ) |
| #define S3C2412_GPIO_SLPCON_HIGH ( 0x01 ) |
| #define S3C2412_GPIO_SLPCON_IN ( 0x02 ) |
| #define S3C2412_GPIO_SLPCON_PULL ( 0x03 ) |
| |
| #define S3C2412_SLPCON_LOW(x) ( 0x00 << ((x) * 2)) |
| #define S3C2412_SLPCON_HIGH(x) ( 0x01 << ((x) * 2)) |
| #define S3C2412_SLPCON_IN(x) ( 0x02 << ((x) * 2)) |
| #define S3C2412_SLPCON_PULL(x) ( 0x03 << ((x) * 2)) |
| #define S3C2412_SLPCON_EINT(x) ( 0x02 << ((x) * 2)) /* only IRQ pins */ |
| #define S3C2412_SLPCON_MASK(x) ( 0x03 << ((x) * 2)) |
| |
| #define S3C2412_SLPCON_ALL_LOW (0x0) |
| #define S3C2412_SLPCON_ALL_HIGH (0x11111111 | 0x44444444) |
| #define S3C2412_SLPCON_ALL_IN (0x22222222 | 0x88888888) |
| #define S3C2412_SLPCON_ALL_PULL (0x33333333) |
| |
| #endif /* __ASM_ARCH_REGS_GPIO_H */ |
| |
