|  | /* | 
|  | * twl-regulator.c -- support regulators in twl4030/twl6030 family chips | 
|  | * | 
|  | * Copyright (C) 2008 David Brownell | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License as published by | 
|  | * the Free Software Foundation; either version 2 of the License, or | 
|  | * (at your option) any later version. | 
|  | */ | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/err.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/of_device.h> | 
|  | #include <linux/regulator/driver.h> | 
|  | #include <linux/regulator/machine.h> | 
|  | #include <linux/regulator/of_regulator.h> | 
|  | #include <linux/i2c/twl.h> | 
|  |  | 
|  |  | 
|  | /* | 
|  | * The TWL4030/TW5030/TPS659x0/TWL6030 family chips include power management, a | 
|  | * USB OTG transceiver, an RTC, ADC, PWM, and lots more.  Some versions | 
|  | * include an audio codec, battery charger, and more voltage regulators. | 
|  | * These chips are often used in OMAP-based systems. | 
|  | * | 
|  | * This driver implements software-based resource control for various | 
|  | * voltage regulators.  This is usually augmented with state machine | 
|  | * based control. | 
|  | */ | 
|  |  | 
|  | struct twlreg_info { | 
|  | /* start of regulator's PM_RECEIVER control register bank */ | 
|  | u8			base; | 
|  |  | 
|  | /* twl resource ID, for resource control state machine */ | 
|  | u8			id; | 
|  |  | 
|  | /* voltage in mV = table[VSEL]; table_len must be a power-of-two */ | 
|  | u8			table_len; | 
|  | const u16		*table; | 
|  |  | 
|  | /* regulator specific turn-on delay */ | 
|  | u16			delay; | 
|  |  | 
|  | /* State REMAP default configuration */ | 
|  | u8			remap; | 
|  |  | 
|  | /* chip constraints on regulator behavior */ | 
|  | u16			min_mV; | 
|  | u16			max_mV; | 
|  |  | 
|  | u8			flags; | 
|  |  | 
|  | /* used by regulator core */ | 
|  | struct regulator_desc	desc; | 
|  |  | 
|  | /* chip specific features */ | 
|  | unsigned long 		features; | 
|  |  | 
|  | /* | 
|  | * optional override functions for voltage set/get | 
|  | * these are currently only used for SMPS regulators | 
|  | */ | 
|  | int			(*get_voltage)(void *data); | 
|  | int			(*set_voltage)(void *data, int target_uV); | 
|  |  | 
|  | /* data passed from board for external get/set voltage */ | 
|  | void			*data; | 
|  | }; | 
|  |  | 
|  |  | 
|  | /* LDO control registers ... offset is from the base of its register bank. | 
|  | * The first three registers of all power resource banks help hardware to | 
|  | * manage the various resource groups. | 
|  | */ | 
|  | /* Common offset in TWL4030/6030 */ | 
|  | #define VREG_GRP		0 | 
|  | /* TWL4030 register offsets */ | 
|  | #define VREG_TYPE		1 | 
|  | #define VREG_REMAP		2 | 
|  | #define VREG_DEDICATED		3	/* LDO control */ | 
|  | #define VREG_VOLTAGE_SMPS_4030	9 | 
|  | /* TWL6030 register offsets */ | 
|  | #define VREG_TRANS		1 | 
|  | #define VREG_STATE		2 | 
|  | #define VREG_VOLTAGE		3 | 
|  | #define VREG_VOLTAGE_SMPS	4 | 
|  | /* TWL6030 Misc register offsets */ | 
|  | #define VREG_BC_ALL		1 | 
|  | #define VREG_BC_REF		2 | 
|  | #define VREG_BC_PROC		3 | 
|  | #define VREG_BC_CLK_RST		4 | 
|  |  | 
|  | /* TWL6030 LDO register values for CFG_STATE */ | 
|  | #define TWL6030_CFG_STATE_OFF	0x00 | 
|  | #define TWL6030_CFG_STATE_ON	0x01 | 
|  | #define TWL6030_CFG_STATE_OFF2	0x02 | 
|  | #define TWL6030_CFG_STATE_SLEEP	0x03 | 
|  | #define TWL6030_CFG_STATE_GRP_SHIFT	5 | 
|  | #define TWL6030_CFG_STATE_APP_SHIFT	2 | 
|  | #define TWL6030_CFG_STATE_APP_MASK	(0x03 << TWL6030_CFG_STATE_APP_SHIFT) | 
|  | #define TWL6030_CFG_STATE_APP(v)	(((v) & TWL6030_CFG_STATE_APP_MASK) >>\ | 
|  | TWL6030_CFG_STATE_APP_SHIFT) | 
|  |  | 
|  | /* Flags for SMPS Voltage reading */ | 
|  | #define SMPS_OFFSET_EN		BIT(0) | 
|  | #define SMPS_EXTENDED_EN	BIT(1) | 
|  |  | 
|  | /* twl6025 SMPS EPROM values */ | 
|  | #define TWL6030_SMPS_OFFSET		0xB0 | 
|  | #define TWL6030_SMPS_MULT		0xB3 | 
|  | #define SMPS_MULTOFFSET_SMPS4	BIT(0) | 
|  | #define SMPS_MULTOFFSET_VIO	BIT(1) | 
|  | #define SMPS_MULTOFFSET_SMPS3	BIT(6) | 
|  |  | 
|  | static inline int | 
|  | twlreg_read(struct twlreg_info *info, unsigned slave_subgp, unsigned offset) | 
|  | { | 
|  | u8 value; | 
|  | int status; | 
|  |  | 
|  | status = twl_i2c_read_u8(slave_subgp, | 
|  | &value, info->base + offset); | 
|  | return (status < 0) ? status : value; | 
|  | } | 
|  |  | 
|  | static inline int | 
|  | twlreg_write(struct twlreg_info *info, unsigned slave_subgp, unsigned offset, | 
|  | u8 value) | 
|  | { | 
|  | return twl_i2c_write_u8(slave_subgp, | 
|  | value, info->base + offset); | 
|  | } | 
|  |  | 
|  | /*----------------------------------------------------------------------*/ | 
|  |  | 
|  | /* generic power resource operations, which work on all regulators */ | 
|  |  | 
|  | static int twlreg_grp(struct regulator_dev *rdev) | 
|  | { | 
|  | return twlreg_read(rdev_get_drvdata(rdev), TWL_MODULE_PM_RECEIVER, | 
|  | VREG_GRP); | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Enable/disable regulators by joining/leaving the P1 (processor) group. | 
|  | * We assume nobody else is updating the DEV_GRP registers. | 
|  | */ | 
|  | /* definition for 4030 family */ | 
|  | #define P3_GRP_4030	BIT(7)		/* "peripherals" */ | 
|  | #define P2_GRP_4030	BIT(6)		/* secondary processor, modem, etc */ | 
|  | #define P1_GRP_4030	BIT(5)		/* CPU/Linux */ | 
|  | /* definition for 6030 family */ | 
|  | #define P3_GRP_6030	BIT(2)		/* secondary processor, modem, etc */ | 
|  | #define P2_GRP_6030	BIT(1)		/* "peripherals" */ | 
|  | #define P1_GRP_6030	BIT(0)		/* CPU/Linux */ | 
|  |  | 
|  | static int twl4030reg_is_enabled(struct regulator_dev *rdev) | 
|  | { | 
|  | int	state = twlreg_grp(rdev); | 
|  |  | 
|  | if (state < 0) | 
|  | return state; | 
|  |  | 
|  | return state & P1_GRP_4030; | 
|  | } | 
|  |  | 
|  | static int twl6030reg_is_enabled(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			grp = 0, val; | 
|  |  | 
|  | if (!(twl_class_is_6030() && (info->features & TWL6025_SUBCLASS))) { | 
|  | grp = twlreg_grp(rdev); | 
|  | if (grp < 0) | 
|  | return grp; | 
|  | grp &= P1_GRP_6030; | 
|  | } else { | 
|  | grp = 1; | 
|  | } | 
|  |  | 
|  | val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE); | 
|  | val = TWL6030_CFG_STATE_APP(val); | 
|  |  | 
|  | return grp && (val == TWL6030_CFG_STATE_ON); | 
|  | } | 
|  |  | 
|  | static int twl4030reg_enable(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			grp; | 
|  | int			ret; | 
|  |  | 
|  | grp = twlreg_grp(rdev); | 
|  | if (grp < 0) | 
|  | return grp; | 
|  |  | 
|  | grp |= P1_GRP_4030; | 
|  |  | 
|  | ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_GRP, grp); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int twl6030reg_enable(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			grp = 0; | 
|  | int			ret; | 
|  |  | 
|  | if (!(twl_class_is_6030() && (info->features & TWL6025_SUBCLASS))) | 
|  | grp = twlreg_grp(rdev); | 
|  | if (grp < 0) | 
|  | return grp; | 
|  |  | 
|  | ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, | 
|  | grp << TWL6030_CFG_STATE_GRP_SHIFT | | 
|  | TWL6030_CFG_STATE_ON); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int twl4030reg_enable_time(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return info->delay; | 
|  | } | 
|  |  | 
|  | static int twl6030reg_enable_time(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return info->delay; | 
|  | } | 
|  |  | 
|  | static int twl4030reg_disable(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			grp; | 
|  | int			ret; | 
|  |  | 
|  | grp = twlreg_grp(rdev); | 
|  | if (grp < 0) | 
|  | return grp; | 
|  |  | 
|  | grp &= ~(P1_GRP_4030 | P2_GRP_4030 | P3_GRP_4030); | 
|  |  | 
|  | ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_GRP, grp); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int twl6030reg_disable(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			grp = 0; | 
|  | int			ret; | 
|  |  | 
|  | if (!(twl_class_is_6030() && (info->features & TWL6025_SUBCLASS))) | 
|  | grp = P1_GRP_6030 | P2_GRP_6030 | P3_GRP_6030; | 
|  |  | 
|  | /* For 6030, set the off state for all grps enabled */ | 
|  | ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, | 
|  | (grp) << TWL6030_CFG_STATE_GRP_SHIFT | | 
|  | TWL6030_CFG_STATE_OFF); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int twl4030reg_get_status(struct regulator_dev *rdev) | 
|  | { | 
|  | int	state = twlreg_grp(rdev); | 
|  |  | 
|  | if (state < 0) | 
|  | return state; | 
|  | state &= 0x0f; | 
|  |  | 
|  | /* assume state != WARM_RESET; we'd not be running...  */ | 
|  | if (!state) | 
|  | return REGULATOR_STATUS_OFF; | 
|  | return (state & BIT(3)) | 
|  | ? REGULATOR_STATUS_NORMAL | 
|  | : REGULATOR_STATUS_STANDBY; | 
|  | } | 
|  |  | 
|  | static int twl6030reg_get_status(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			val; | 
|  |  | 
|  | val = twlreg_grp(rdev); | 
|  | if (val < 0) | 
|  | return val; | 
|  |  | 
|  | val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE); | 
|  |  | 
|  | switch (TWL6030_CFG_STATE_APP(val)) { | 
|  | case TWL6030_CFG_STATE_ON: | 
|  | return REGULATOR_STATUS_NORMAL; | 
|  |  | 
|  | case TWL6030_CFG_STATE_SLEEP: | 
|  | return REGULATOR_STATUS_STANDBY; | 
|  |  | 
|  | case TWL6030_CFG_STATE_OFF: | 
|  | case TWL6030_CFG_STATE_OFF2: | 
|  | default: | 
|  | break; | 
|  | } | 
|  |  | 
|  | return REGULATOR_STATUS_OFF; | 
|  | } | 
|  |  | 
|  | static int twl4030reg_set_mode(struct regulator_dev *rdev, unsigned mode) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | unsigned		message; | 
|  | int			status; | 
|  |  | 
|  | /* We can only set the mode through state machine commands... */ | 
|  | switch (mode) { | 
|  | case REGULATOR_MODE_NORMAL: | 
|  | message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_ACTIVE); | 
|  | break; | 
|  | case REGULATOR_MODE_STANDBY: | 
|  | message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_SLEEP); | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | /* Ensure the resource is associated with some group */ | 
|  | status = twlreg_grp(rdev); | 
|  | if (status < 0) | 
|  | return status; | 
|  | if (!(status & (P3_GRP_4030 | P2_GRP_4030 | P1_GRP_4030))) | 
|  | return -EACCES; | 
|  |  | 
|  | status = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, | 
|  | message >> 8, TWL4030_PM_MASTER_PB_WORD_MSB); | 
|  | if (status < 0) | 
|  | return status; | 
|  |  | 
|  | return twl_i2c_write_u8(TWL_MODULE_PM_MASTER, | 
|  | message & 0xff, TWL4030_PM_MASTER_PB_WORD_LSB); | 
|  | } | 
|  |  | 
|  | static int twl6030reg_set_mode(struct regulator_dev *rdev, unsigned mode) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int grp = 0; | 
|  | int val; | 
|  |  | 
|  | if (!(twl_class_is_6030() && (info->features & TWL6025_SUBCLASS))) | 
|  | grp = twlreg_grp(rdev); | 
|  |  | 
|  | if (grp < 0) | 
|  | return grp; | 
|  |  | 
|  | /* Compose the state register settings */ | 
|  | val = grp << TWL6030_CFG_STATE_GRP_SHIFT; | 
|  | /* We can only set the mode through state machine commands... */ | 
|  | switch (mode) { | 
|  | case REGULATOR_MODE_NORMAL: | 
|  | val |= TWL6030_CFG_STATE_ON; | 
|  | break; | 
|  | case REGULATOR_MODE_STANDBY: | 
|  | val |= TWL6030_CFG_STATE_SLEEP; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, val); | 
|  | } | 
|  |  | 
|  | /*----------------------------------------------------------------------*/ | 
|  |  | 
|  | /* | 
|  | * Support for adjustable-voltage LDOs uses a four bit (or less) voltage | 
|  | * select field in its control register.   We use tables indexed by VSEL | 
|  | * to record voltages in milliVolts.  (Accuracy is about three percent.) | 
|  | * | 
|  | * Note that VSEL values for VAUX2 changed in twl5030 and newer silicon; | 
|  | * currently handled by listing two slightly different VAUX2 regulators, | 
|  | * only one of which will be configured. | 
|  | * | 
|  | * VSEL values documented as "TI cannot support these values" are flagged | 
|  | * in these tables as UNSUP() values; we normally won't assign them. | 
|  | * | 
|  | * VAUX3 at 3V is incorrectly listed in some TI manuals as unsupported. | 
|  | * TI are revising the twl5030/tps659x0 specs to support that 3.0V setting. | 
|  | */ | 
|  | #define UNSUP_MASK	0x8000 | 
|  |  | 
|  | #define UNSUP(x)	(UNSUP_MASK | (x)) | 
|  | #define IS_UNSUP(info, x)			\ | 
|  | ((UNSUP_MASK & (x)) &&			\ | 
|  | !((info)->features & TWL4030_ALLOW_UNSUPPORTED)) | 
|  | #define LDO_MV(x)	(~UNSUP_MASK & (x)) | 
|  |  | 
|  |  | 
|  | static const u16 VAUX1_VSEL_table[] = { | 
|  | UNSUP(1500), UNSUP(1800), 2500, 2800, | 
|  | 3000, 3000, 3000, 3000, | 
|  | }; | 
|  | static const u16 VAUX2_4030_VSEL_table[] = { | 
|  | UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300, | 
|  | 1500, 1800, UNSUP(1850), 2500, | 
|  | UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), | 
|  | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | 
|  | }; | 
|  | static const u16 VAUX2_VSEL_table[] = { | 
|  | 1700, 1700, 1900, 1300, | 
|  | 1500, 1800, 2000, 2500, | 
|  | 2100, 2800, 2200, 2300, | 
|  | 2400, 2400, 2400, 2400, | 
|  | }; | 
|  | static const u16 VAUX3_VSEL_table[] = { | 
|  | 1500, 1800, 2500, 2800, | 
|  | 3000, 3000, 3000, 3000, | 
|  | }; | 
|  | static const u16 VAUX4_VSEL_table[] = { | 
|  | 700, 1000, 1200, UNSUP(1300), | 
|  | 1500, 1800, UNSUP(1850), 2500, | 
|  | UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), | 
|  | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | 
|  | }; | 
|  | static const u16 VMMC1_VSEL_table[] = { | 
|  | 1850, 2850, 3000, 3150, | 
|  | }; | 
|  | static const u16 VMMC2_VSEL_table[] = { | 
|  | UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300), | 
|  | UNSUP(1500), UNSUP(1800), 1850, UNSUP(2500), | 
|  | 2600, 2800, 2850, 3000, | 
|  | 3150, 3150, 3150, 3150, | 
|  | }; | 
|  | static const u16 VPLL1_VSEL_table[] = { | 
|  | 1000, 1200, 1300, 1800, | 
|  | UNSUP(2800), UNSUP(3000), UNSUP(3000), UNSUP(3000), | 
|  | }; | 
|  | static const u16 VPLL2_VSEL_table[] = { | 
|  | 700, 1000, 1200, 1300, | 
|  | UNSUP(1500), 1800, UNSUP(1850), UNSUP(2500), | 
|  | UNSUP(2600), UNSUP(2800), UNSUP(2850), UNSUP(3000), | 
|  | UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | 
|  | }; | 
|  | static const u16 VSIM_VSEL_table[] = { | 
|  | UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800, | 
|  | 2800, 3000, 3000, 3000, | 
|  | }; | 
|  | static const u16 VDAC_VSEL_table[] = { | 
|  | 1200, 1300, 1800, 1800, | 
|  | }; | 
|  | static const u16 VDD1_VSEL_table[] = { | 
|  | 800, 1450, | 
|  | }; | 
|  | static const u16 VDD2_VSEL_table[] = { | 
|  | 800, 1450, 1500, | 
|  | }; | 
|  | static const u16 VIO_VSEL_table[] = { | 
|  | 1800, 1850, | 
|  | }; | 
|  | static const u16 VINTANA2_VSEL_table[] = { | 
|  | 2500, 2750, | 
|  | }; | 
|  |  | 
|  | static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			mV = info->table[index]; | 
|  |  | 
|  | return IS_UNSUP(info, mV) ? 0 : (LDO_MV(mV) * 1000); | 
|  | } | 
|  |  | 
|  | static int | 
|  | twl4030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE, | 
|  | selector); | 
|  | } | 
|  |  | 
|  | static int twl4030ldo_get_voltage(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int		vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, | 
|  | VREG_VOLTAGE); | 
|  |  | 
|  | if (vsel < 0) | 
|  | return vsel; | 
|  |  | 
|  | vsel &= info->table_len - 1; | 
|  | return LDO_MV(info->table[vsel]) * 1000; | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twl4030ldo_ops = { | 
|  | .list_voltage	= twl4030ldo_list_voltage, | 
|  |  | 
|  | .set_voltage_sel = twl4030ldo_set_voltage_sel, | 
|  | .get_voltage	= twl4030ldo_get_voltage, | 
|  |  | 
|  | .enable		= twl4030reg_enable, | 
|  | .disable	= twl4030reg_disable, | 
|  | .is_enabled	= twl4030reg_is_enabled, | 
|  | .enable_time	= twl4030reg_enable_time, | 
|  |  | 
|  | .set_mode	= twl4030reg_set_mode, | 
|  |  | 
|  | .get_status	= twl4030reg_get_status, | 
|  | }; | 
|  |  | 
|  | static int | 
|  | twl4030smps_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV, | 
|  | unsigned *selector) | 
|  | { | 
|  | struct twlreg_info *info = rdev_get_drvdata(rdev); | 
|  | int vsel = DIV_ROUND_UP(min_uV - 600000, 12500); | 
|  |  | 
|  | if (info->set_voltage) { | 
|  | return info->set_voltage(info->data, min_uV); | 
|  | } else { | 
|  | twlreg_write(info, TWL_MODULE_PM_RECEIVER, | 
|  | VREG_VOLTAGE_SMPS_4030, vsel); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int twl4030smps_get_voltage(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info *info = rdev_get_drvdata(rdev); | 
|  | int vsel; | 
|  |  | 
|  | if (info->get_voltage) | 
|  | return info->get_voltage(info->data); | 
|  |  | 
|  | vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, | 
|  | VREG_VOLTAGE_SMPS_4030); | 
|  |  | 
|  | return vsel * 12500 + 600000; | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twl4030smps_ops = { | 
|  | .set_voltage	= twl4030smps_set_voltage, | 
|  | .get_voltage	= twl4030smps_get_voltage, | 
|  | }; | 
|  |  | 
|  | static int twl6030coresmps_set_voltage(struct regulator_dev *rdev, int min_uV, | 
|  | int max_uV, unsigned *selector) | 
|  | { | 
|  | struct twlreg_info *info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | if (info->set_voltage) | 
|  | return info->set_voltage(info->data, min_uV); | 
|  |  | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | static int twl6030coresmps_get_voltage(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info *info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | if (info->get_voltage) | 
|  | return info->get_voltage(info->data); | 
|  |  | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twl6030coresmps_ops = { | 
|  | .set_voltage	= twl6030coresmps_set_voltage, | 
|  | .get_voltage	= twl6030coresmps_get_voltage, | 
|  | }; | 
|  |  | 
|  | static int twl6030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return ((info->min_mV + (index * 100)) * 1000); | 
|  | } | 
|  |  | 
|  | static int | 
|  | twl6030ldo_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV, | 
|  | unsigned *selector) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int			vsel; | 
|  |  | 
|  | if ((min_uV/1000 < info->min_mV) || (max_uV/1000 > info->max_mV)) | 
|  | return -EDOM; | 
|  |  | 
|  | /* | 
|  | * Use the below formula to calculate vsel | 
|  | * mV = 1000mv + 100mv * (vsel - 1) | 
|  | */ | 
|  | vsel = (min_uV/1000 - 1000)/100 + 1; | 
|  | *selector = vsel; | 
|  | return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE, vsel); | 
|  |  | 
|  | } | 
|  |  | 
|  | static int twl6030ldo_get_voltage(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int		vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, | 
|  | VREG_VOLTAGE); | 
|  |  | 
|  | if (vsel < 0) | 
|  | return vsel; | 
|  |  | 
|  | /* | 
|  | * Use the below formula to calculate vsel | 
|  | * mV = 1000mv + 100mv * (vsel - 1) | 
|  | */ | 
|  | return (1000 + (100 * (vsel - 1))) * 1000; | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twl6030ldo_ops = { | 
|  | .list_voltage	= twl6030ldo_list_voltage, | 
|  |  | 
|  | .set_voltage	= twl6030ldo_set_voltage, | 
|  | .get_voltage	= twl6030ldo_get_voltage, | 
|  |  | 
|  | .enable		= twl6030reg_enable, | 
|  | .disable	= twl6030reg_disable, | 
|  | .is_enabled	= twl6030reg_is_enabled, | 
|  | .enable_time	= twl6030reg_enable_time, | 
|  |  | 
|  | .set_mode	= twl6030reg_set_mode, | 
|  |  | 
|  | .get_status	= twl6030reg_get_status, | 
|  | }; | 
|  |  | 
|  | /*----------------------------------------------------------------------*/ | 
|  |  | 
|  | /* | 
|  | * Fixed voltage LDOs don't have a VSEL field to update. | 
|  | */ | 
|  | static int twlfixed_list_voltage(struct regulator_dev *rdev, unsigned index) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return info->min_mV * 1000; | 
|  | } | 
|  |  | 
|  | static int twlfixed_get_voltage(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return info->min_mV * 1000; | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twl4030fixed_ops = { | 
|  | .list_voltage	= twlfixed_list_voltage, | 
|  |  | 
|  | .get_voltage	= twlfixed_get_voltage, | 
|  |  | 
|  | .enable		= twl4030reg_enable, | 
|  | .disable	= twl4030reg_disable, | 
|  | .is_enabled	= twl4030reg_is_enabled, | 
|  | .enable_time	= twl4030reg_enable_time, | 
|  |  | 
|  | .set_mode	= twl4030reg_set_mode, | 
|  |  | 
|  | .get_status	= twl4030reg_get_status, | 
|  | }; | 
|  |  | 
|  | static struct regulator_ops twl6030fixed_ops = { | 
|  | .list_voltage	= twlfixed_list_voltage, | 
|  |  | 
|  | .get_voltage	= twlfixed_get_voltage, | 
|  |  | 
|  | .enable		= twl6030reg_enable, | 
|  | .disable	= twl6030reg_disable, | 
|  | .is_enabled	= twl6030reg_is_enabled, | 
|  | .enable_time	= twl6030reg_enable_time, | 
|  |  | 
|  | .set_mode	= twl6030reg_set_mode, | 
|  |  | 
|  | .get_status	= twl6030reg_get_status, | 
|  | }; | 
|  |  | 
|  | static struct regulator_ops twl6030_fixed_resource = { | 
|  | .enable		= twl6030reg_enable, | 
|  | .disable	= twl6030reg_disable, | 
|  | .is_enabled	= twl6030reg_is_enabled, | 
|  | .enable_time	= twl6030reg_enable_time, | 
|  | .get_status	= twl6030reg_get_status, | 
|  | }; | 
|  |  | 
|  | /* | 
|  | * SMPS status and control | 
|  | */ | 
|  |  | 
|  | static int twl6030smps_list_voltage(struct regulator_dev *rdev, unsigned index) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | int voltage = 0; | 
|  |  | 
|  | switch (info->flags) { | 
|  | case SMPS_OFFSET_EN: | 
|  | voltage = 100000; | 
|  | /* fall through */ | 
|  | case 0: | 
|  | switch (index) { | 
|  | case 0: | 
|  | voltage = 0; | 
|  | break; | 
|  | case 58: | 
|  | voltage = 1350 * 1000; | 
|  | break; | 
|  | case 59: | 
|  | voltage = 1500 * 1000; | 
|  | break; | 
|  | case 60: | 
|  | voltage = 1800 * 1000; | 
|  | break; | 
|  | case 61: | 
|  | voltage = 1900 * 1000; | 
|  | break; | 
|  | case 62: | 
|  | voltage = 2100 * 1000; | 
|  | break; | 
|  | default: | 
|  | voltage += (600000 + (12500 * (index - 1))); | 
|  | } | 
|  | break; | 
|  | case SMPS_EXTENDED_EN: | 
|  | switch (index) { | 
|  | case 0: | 
|  | voltage = 0; | 
|  | break; | 
|  | case 58: | 
|  | voltage = 2084 * 1000; | 
|  | break; | 
|  | case 59: | 
|  | voltage = 2315 * 1000; | 
|  | break; | 
|  | case 60: | 
|  | voltage = 2778 * 1000; | 
|  | break; | 
|  | case 61: | 
|  | voltage = 2932 * 1000; | 
|  | break; | 
|  | case 62: | 
|  | voltage = 3241 * 1000; | 
|  | break; | 
|  | default: | 
|  | voltage = (1852000 + (38600 * (index - 1))); | 
|  | } | 
|  | break; | 
|  | case SMPS_OFFSET_EN | SMPS_EXTENDED_EN: | 
|  | switch (index) { | 
|  | case 0: | 
|  | voltage = 0; | 
|  | break; | 
|  | case 58: | 
|  | voltage = 4167 * 1000; | 
|  | break; | 
|  | case 59: | 
|  | voltage = 2315 * 1000; | 
|  | break; | 
|  | case 60: | 
|  | voltage = 2778 * 1000; | 
|  | break; | 
|  | case 61: | 
|  | voltage = 2932 * 1000; | 
|  | break; | 
|  | case 62: | 
|  | voltage = 3241 * 1000; | 
|  | break; | 
|  | default: | 
|  | voltage = (2161000 + (38600 * (index - 1))); | 
|  | } | 
|  | break; | 
|  | } | 
|  |  | 
|  | return voltage; | 
|  | } | 
|  |  | 
|  | static int | 
|  | twl6030smps_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV, | 
|  | unsigned int *selector) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  | int	vsel = 0; | 
|  |  | 
|  | switch (info->flags) { | 
|  | case 0: | 
|  | if (min_uV == 0) | 
|  | vsel = 0; | 
|  | else if ((min_uV >= 600000) && (min_uV <= 1300000)) { | 
|  | int calc_uV; | 
|  | vsel = DIV_ROUND_UP(min_uV - 600000, 12500); | 
|  | vsel++; | 
|  | calc_uV = twl6030smps_list_voltage(rdev, vsel); | 
|  | if (calc_uV > max_uV) | 
|  | return -EINVAL; | 
|  | } | 
|  | /* Values 1..57 for vsel are linear and can be calculated | 
|  | * values 58..62 are non linear. | 
|  | */ | 
|  | else if ((min_uV > 1900000) && (max_uV >= 2100000)) | 
|  | vsel = 62; | 
|  | else if ((min_uV > 1800000) && (max_uV >= 1900000)) | 
|  | vsel = 61; | 
|  | else if ((min_uV > 1500000) && (max_uV >= 1800000)) | 
|  | vsel = 60; | 
|  | else if ((min_uV > 1350000) && (max_uV >= 1500000)) | 
|  | vsel = 59; | 
|  | else if ((min_uV > 1300000) && (max_uV >= 1350000)) | 
|  | vsel = 58; | 
|  | else | 
|  | return -EINVAL; | 
|  | break; | 
|  | case SMPS_OFFSET_EN: | 
|  | if (min_uV == 0) | 
|  | vsel = 0; | 
|  | else if ((min_uV >= 700000) && (min_uV <= 1420000)) { | 
|  | int calc_uV; | 
|  | vsel = DIV_ROUND_UP(min_uV - 700000, 12500); | 
|  | vsel++; | 
|  | calc_uV = twl6030smps_list_voltage(rdev, vsel); | 
|  | if (calc_uV > max_uV) | 
|  | return -EINVAL; | 
|  | } | 
|  | /* Values 1..57 for vsel are linear and can be calculated | 
|  | * values 58..62 are non linear. | 
|  | */ | 
|  | else if ((min_uV > 1900000) && (max_uV >= 2100000)) | 
|  | vsel = 62; | 
|  | else if ((min_uV > 1800000) && (max_uV >= 1900000)) | 
|  | vsel = 61; | 
|  | else if ((min_uV > 1350000) && (max_uV >= 1800000)) | 
|  | vsel = 60; | 
|  | else if ((min_uV > 1350000) && (max_uV >= 1500000)) | 
|  | vsel = 59; | 
|  | else if ((min_uV > 1300000) && (max_uV >= 1350000)) | 
|  | vsel = 58; | 
|  | else | 
|  | return -EINVAL; | 
|  | break; | 
|  | case SMPS_EXTENDED_EN: | 
|  | if (min_uV == 0) { | 
|  | vsel = 0; | 
|  | } else if ((min_uV >= 1852000) && (max_uV <= 4013600)) { | 
|  | vsel = DIV_ROUND_UP(min_uV - 1852000, 38600); | 
|  | vsel++; | 
|  | } | 
|  | break; | 
|  | case SMPS_OFFSET_EN|SMPS_EXTENDED_EN: | 
|  | if (min_uV == 0) { | 
|  | vsel = 0; | 
|  | } else if ((min_uV >= 2161000) && (max_uV <= 4321000)) { | 
|  | vsel = DIV_ROUND_UP(min_uV - 2161000, 38600); | 
|  | vsel++; | 
|  | } | 
|  | break; | 
|  | } | 
|  |  | 
|  | *selector = vsel; | 
|  |  | 
|  | return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS, | 
|  | vsel); | 
|  | } | 
|  |  | 
|  | static int twl6030smps_get_voltage_sel(struct regulator_dev *rdev) | 
|  | { | 
|  | struct twlreg_info	*info = rdev_get_drvdata(rdev); | 
|  |  | 
|  | return twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS); | 
|  | } | 
|  |  | 
|  | static struct regulator_ops twlsmps_ops = { | 
|  | .list_voltage		= twl6030smps_list_voltage, | 
|  |  | 
|  | .set_voltage		= twl6030smps_set_voltage, | 
|  | .get_voltage_sel	= twl6030smps_get_voltage_sel, | 
|  |  | 
|  | .enable			= twl6030reg_enable, | 
|  | .disable		= twl6030reg_disable, | 
|  | .is_enabled		= twl6030reg_is_enabled, | 
|  | .enable_time		= twl6030reg_enable_time, | 
|  |  | 
|  | .set_mode		= twl6030reg_set_mode, | 
|  |  | 
|  | .get_status		= twl6030reg_get_status, | 
|  | }; | 
|  |  | 
|  | /*----------------------------------------------------------------------*/ | 
|  |  | 
|  | #define TWL4030_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \ | 
|  | remap_conf) \ | 
|  | TWL_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \ | 
|  | remap_conf, TWL4030, twl4030fixed_ops) | 
|  | #define TWL6030_FIXED_LDO(label, offset, mVolts, turnon_delay) \ | 
|  | TWL_FIXED_LDO(label, offset, mVolts, 0x0, turnon_delay, \ | 
|  | 0x0, TWL6030, twl6030fixed_ops) | 
|  |  | 
|  | #define TWL4030_ADJUSTABLE_LDO(label, offset, num, turnon_delay, remap_conf) \ | 
|  | static struct twlreg_info TWL4030_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .id = num, \ | 
|  | .table_len = ARRAY_SIZE(label##_VSEL_table), \ | 
|  | .table = label##_VSEL_table, \ | 
|  | .delay = turnon_delay, \ | 
|  | .remap = remap_conf, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL4030_REG_##label, \ | 
|  | .n_voltages = ARRAY_SIZE(label##_VSEL_table), \ | 
|  | .ops = &twl4030ldo_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf) \ | 
|  | static struct twlreg_info TWL4030_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .id = num, \ | 
|  | .delay = turnon_delay, \ | 
|  | .remap = remap_conf, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL4030_REG_##label, \ | 
|  | .ops = &twl4030smps_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL6030_ADJUSTABLE_SMPS(label) \ | 
|  | static struct twlreg_info TWL6030_INFO_##label = { \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL6030_REG_##label, \ | 
|  | .ops = &twl6030coresmps_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL6030_ADJUSTABLE_LDO(label, offset, min_mVolts, max_mVolts) \ | 
|  | static struct twlreg_info TWL6030_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .min_mV = min_mVolts, \ | 
|  | .max_mV = max_mVolts, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL6030_REG_##label, \ | 
|  | .n_voltages = (max_mVolts - min_mVolts)/100 + 1, \ | 
|  | .ops = &twl6030ldo_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL6025_ADJUSTABLE_LDO(label, offset, min_mVolts, max_mVolts) \ | 
|  | static struct twlreg_info TWL6025_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .min_mV = min_mVolts, \ | 
|  | .max_mV = max_mVolts, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL6025_REG_##label, \ | 
|  | .n_voltages = ((max_mVolts - min_mVolts)/100) + 1, \ | 
|  | .ops = &twl6030ldo_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL_FIXED_LDO(label, offset, mVolts, num, turnon_delay, remap_conf, \ | 
|  | family, operations) \ | 
|  | static struct twlreg_info TWLFIXED_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .id = num, \ | 
|  | .min_mV = mVolts, \ | 
|  | .delay = turnon_delay, \ | 
|  | .remap = remap_conf, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = family##_REG_##label, \ | 
|  | .n_voltages = 1, \ | 
|  | .ops = &operations, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL6030_FIXED_RESOURCE(label, offset, turnon_delay) \ | 
|  | static struct twlreg_info TWLRES_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .delay = turnon_delay, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL6030_REG_##label, \ | 
|  | .ops = &twl6030_fixed_resource, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | #define TWL6025_ADJUSTABLE_SMPS(label, offset) \ | 
|  | static struct twlreg_info TWLSMPS_INFO_##label = { \ | 
|  | .base = offset, \ | 
|  | .min_mV = 600, \ | 
|  | .max_mV = 2100, \ | 
|  | .desc = { \ | 
|  | .name = #label, \ | 
|  | .id = TWL6025_REG_##label, \ | 
|  | .n_voltages = 63, \ | 
|  | .ops = &twlsmps_ops, \ | 
|  | .type = REGULATOR_VOLTAGE, \ | 
|  | .owner = THIS_MODULE, \ | 
|  | }, \ | 
|  | } | 
|  |  | 
|  | /* | 
|  | * We list regulators here if systems need some level of | 
|  | * software control over them after boot. | 
|  | */ | 
|  | TWL4030_ADJUSTABLE_LDO(VAUX1, 0x17, 1, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VAUX2, 0x1b, 2, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VAUX3, 0x1f, 3, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VAUX4, 0x23, 4, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VMMC1, 0x27, 5, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VMMC2, 0x2b, 6, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VPLL1, 0x2f, 7, 100, 0x00); | 
|  | TWL4030_ADJUSTABLE_LDO(VPLL2, 0x33, 8, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); | 
|  | TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); | 
|  | TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); | 
|  | TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08); | 
|  | TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08); | 
|  | /* VUSBCP is managed *only* by the USB subchip */ | 
|  | /* 6030 REG with base as PMC Slave Misc : 0x0030 */ | 
|  | /* Turnon-delay and remap configuration values for 6030 are not | 
|  | verified since the specification is not public */ | 
|  | TWL6030_ADJUSTABLE_SMPS(VDD1); | 
|  | TWL6030_ADJUSTABLE_SMPS(VDD2); | 
|  | TWL6030_ADJUSTABLE_SMPS(VDD3); | 
|  | TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54, 1000, 3300); | 
|  | TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58, 1000, 3300); | 
|  | TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c, 1000, 3300); | 
|  | TWL6030_ADJUSTABLE_LDO(VMMC, 0x68, 1000, 3300); | 
|  | TWL6030_ADJUSTABLE_LDO(VPP, 0x6c, 1000, 3300); | 
|  | TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74, 1000, 3300); | 
|  | /* 6025 are renamed compared to 6030 versions */ | 
|  | TWL6025_ADJUSTABLE_LDO(LDO2, 0x54, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO4, 0x58, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO3, 0x5c, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO5, 0x68, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO1, 0x6c, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO7, 0x74, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDO6, 0x60, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDOLN, 0x64, 1000, 3300); | 
|  | TWL6025_ADJUSTABLE_LDO(LDOUSB, 0x70, 1000, 3300); | 
|  | TWL4030_FIXED_LDO(VINTANA2, 0x3f, 1500, 11, 100, 0x08); | 
|  | TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08); | 
|  | TWL4030_FIXED_LDO(VUSB1V5, 0x71, 1500, 17, 100, 0x08); | 
|  | TWL4030_FIXED_LDO(VUSB1V8, 0x74, 1800, 18, 100, 0x08); | 
|  | TWL4030_FIXED_LDO(VUSB3V1, 0x77, 3100, 19, 150, 0x08); | 
|  | TWL6030_FIXED_LDO(VANA, 0x50, 2100, 0); | 
|  | TWL6030_FIXED_LDO(VCXIO, 0x60, 1800, 0); | 
|  | TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0); | 
|  | TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 0); | 
|  | TWL6030_FIXED_LDO(V1V8, 0x16, 1800, 0); | 
|  | TWL6030_FIXED_LDO(V2V1, 0x1c, 2100, 0); | 
|  | TWL6030_FIXED_RESOURCE(CLK32KG, 0x8C, 0); | 
|  | TWL6025_ADJUSTABLE_SMPS(SMPS3, 0x34); | 
|  | TWL6025_ADJUSTABLE_SMPS(SMPS4, 0x10); | 
|  | TWL6025_ADJUSTABLE_SMPS(VIO, 0x16); | 
|  |  | 
|  | static u8 twl_get_smps_offset(void) | 
|  | { | 
|  | u8 value; | 
|  |  | 
|  | twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &value, | 
|  | TWL6030_SMPS_OFFSET); | 
|  | return value; | 
|  | } | 
|  |  | 
|  | static u8 twl_get_smps_mult(void) | 
|  | { | 
|  | u8 value; | 
|  |  | 
|  | twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &value, | 
|  | TWL6030_SMPS_MULT); | 
|  | return value; | 
|  | } | 
|  |  | 
|  | #define TWL_OF_MATCH(comp, family, label) \ | 
|  | { \ | 
|  | .compatible = comp, \ | 
|  | .data = &family##_INFO_##label, \ | 
|  | } | 
|  |  | 
|  | #define TWL4030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL4030, label) | 
|  | #define TWL6030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6030, label) | 
|  | #define TWL6025_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6025, label) | 
|  | #define TWLFIXED_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLFIXED, label) | 
|  | #define TWLRES_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLRES, label) | 
|  | #define TWLSMPS_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLSMPS, label) | 
|  |  | 
|  | static const struct of_device_id twl_of_match[] __devinitconst = { | 
|  | TWL4030_OF_MATCH("ti,twl4030-vaux1", VAUX1), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vaux2", VAUX2_4030), | 
|  | TWL4030_OF_MATCH("ti,twl5030-vaux2", VAUX2), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vaux3", VAUX3), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vaux4", VAUX4), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vmmc1", VMMC1), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vmmc2", VMMC2), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vpll1", VPLL1), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vpll2", VPLL2), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vsim", VSIM), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vdac", VDAC), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vintana2", VINTANA2), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vio", VIO), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vdd1", VDD1), | 
|  | TWL4030_OF_MATCH("ti,twl4030-vdd2", VDD2), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vdd1", VDD1), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vdd2", VDD2), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vdd3", VDD3), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vaux1", VAUX1_6030), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vaux2", VAUX2_6030), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vaux3", VAUX3_6030), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vmmc", VMMC), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vpp", VPP), | 
|  | TWL6030_OF_MATCH("ti,twl6030-vusim", VUSIM), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo2", LDO2), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo4", LDO4), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo3", LDO3), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo5", LDO5), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo1", LDO1), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo7", LDO7), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldo6", LDO6), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldoln", LDOLN), | 
|  | TWL6025_OF_MATCH("ti,twl6025-ldousb", LDOUSB), | 
|  | TWLFIXED_OF_MATCH("ti,twl4030-vintana2", VINTANA2), | 
|  | TWLFIXED_OF_MATCH("ti,twl4030-vintdig", VINTDIG), | 
|  | TWLFIXED_OF_MATCH("ti,twl4030-vusb1v5", VUSB1V5), | 
|  | TWLFIXED_OF_MATCH("ti,twl4030-vusb1v8", VUSB1V8), | 
|  | TWLFIXED_OF_MATCH("ti,twl4030-vusb3v1", VUSB3V1), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-vana", VANA), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-vcxio", VCXIO), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-vdac", VDAC), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-vusb", VUSB), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-v1v8", V1V8), | 
|  | TWLFIXED_OF_MATCH("ti,twl6030-v2v1", V2V1), | 
|  | TWLRES_OF_MATCH("ti,twl6030-clk32kg", CLK32KG), | 
|  | TWLSMPS_OF_MATCH("ti,twl6025-smps3", SMPS3), | 
|  | TWLSMPS_OF_MATCH("ti,twl6025-smps4", SMPS4), | 
|  | TWLSMPS_OF_MATCH("ti,twl6025-vio", VIO), | 
|  | {}, | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, twl_of_match); | 
|  |  | 
|  | static int __devinit twlreg_probe(struct platform_device *pdev) | 
|  | { | 
|  | int				i, id; | 
|  | struct twlreg_info		*info; | 
|  | struct regulator_init_data	*initdata; | 
|  | struct regulation_constraints	*c; | 
|  | struct regulator_dev		*rdev; | 
|  | struct twl_regulator_driver_data	*drvdata; | 
|  | const struct of_device_id	*match; | 
|  | struct regulator_config		config = { }; | 
|  |  | 
|  | match = of_match_device(twl_of_match, &pdev->dev); | 
|  | if (match) { | 
|  | info = match->data; | 
|  | id = info->desc.id; | 
|  | initdata = of_get_regulator_init_data(&pdev->dev, | 
|  | pdev->dev.of_node); | 
|  | drvdata = NULL; | 
|  | } else { | 
|  | id = pdev->id; | 
|  | initdata = pdev->dev.platform_data; | 
|  | for (i = 0, info = NULL; i < ARRAY_SIZE(twl_of_match); i++) { | 
|  | info = twl_of_match[i].data; | 
|  | if (info && info->desc.id == id) | 
|  | break; | 
|  | } | 
|  | if (i == ARRAY_SIZE(twl_of_match)) | 
|  | return -ENODEV; | 
|  |  | 
|  | drvdata = initdata->driver_data; | 
|  | if (!drvdata) | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (!info) | 
|  | return -ENODEV; | 
|  |  | 
|  | if (!initdata) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (drvdata) { | 
|  | /* copy the driver data into regulator data */ | 
|  | info->features = drvdata->features; | 
|  | info->data = drvdata->data; | 
|  | info->set_voltage = drvdata->set_voltage; | 
|  | info->get_voltage = drvdata->get_voltage; | 
|  | } | 
|  |  | 
|  | /* Constrain board-specific capabilities according to what | 
|  | * this driver and the chip itself can actually do. | 
|  | */ | 
|  | c = &initdata->constraints; | 
|  | c->valid_modes_mask &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY; | 
|  | c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE | 
|  | | REGULATOR_CHANGE_MODE | 
|  | | REGULATOR_CHANGE_STATUS; | 
|  | switch (id) { | 
|  | case TWL4030_REG_VIO: | 
|  | case TWL4030_REG_VDD1: | 
|  | case TWL4030_REG_VDD2: | 
|  | case TWL4030_REG_VPLL1: | 
|  | case TWL4030_REG_VINTANA1: | 
|  | case TWL4030_REG_VINTANA2: | 
|  | case TWL4030_REG_VINTDIG: | 
|  | c->always_on = true; | 
|  | break; | 
|  | default: | 
|  | break; | 
|  | } | 
|  |  | 
|  | switch (id) { | 
|  | case TWL6025_REG_SMPS3: | 
|  | if (twl_get_smps_mult() & SMPS_MULTOFFSET_SMPS3) | 
|  | info->flags |= SMPS_EXTENDED_EN; | 
|  | if (twl_get_smps_offset() & SMPS_MULTOFFSET_SMPS3) | 
|  | info->flags |= SMPS_OFFSET_EN; | 
|  | break; | 
|  | case TWL6025_REG_SMPS4: | 
|  | if (twl_get_smps_mult() & SMPS_MULTOFFSET_SMPS4) | 
|  | info->flags |= SMPS_EXTENDED_EN; | 
|  | if (twl_get_smps_offset() & SMPS_MULTOFFSET_SMPS4) | 
|  | info->flags |= SMPS_OFFSET_EN; | 
|  | break; | 
|  | case TWL6025_REG_VIO: | 
|  | if (twl_get_smps_mult() & SMPS_MULTOFFSET_VIO) | 
|  | info->flags |= SMPS_EXTENDED_EN; | 
|  | if (twl_get_smps_offset() & SMPS_MULTOFFSET_VIO) | 
|  | info->flags |= SMPS_OFFSET_EN; | 
|  | break; | 
|  | } | 
|  |  | 
|  | config.dev = &pdev->dev; | 
|  | config.init_data = initdata; | 
|  | config.driver_data = info; | 
|  | config.of_node = pdev->dev.of_node; | 
|  |  | 
|  | rdev = regulator_register(&info->desc, &config); | 
|  | if (IS_ERR(rdev)) { | 
|  | dev_err(&pdev->dev, "can't register %s, %ld\n", | 
|  | info->desc.name, PTR_ERR(rdev)); | 
|  | return PTR_ERR(rdev); | 
|  | } | 
|  | platform_set_drvdata(pdev, rdev); | 
|  |  | 
|  | if (twl_class_is_4030()) | 
|  | twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_REMAP, | 
|  | info->remap); | 
|  |  | 
|  | /* NOTE:  many regulators support short-circuit IRQs (presentable | 
|  | * as REGULATOR_OVER_CURRENT notifications?) configured via: | 
|  | *  - SC_CONFIG | 
|  | *  - SC_DETECT1 (vintana2, vmmc1/2, vaux1/2/3/4) | 
|  | *  - SC_DETECT2 (vusb, vdac, vio, vdd1/2, vpll2) | 
|  | *  - IT_CONFIG | 
|  | */ | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int __devexit twlreg_remove(struct platform_device *pdev) | 
|  | { | 
|  | regulator_unregister(platform_get_drvdata(pdev)); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | MODULE_ALIAS("platform:twl_reg"); | 
|  |  | 
|  | static struct platform_driver twlreg_driver = { | 
|  | .probe		= twlreg_probe, | 
|  | .remove		= __devexit_p(twlreg_remove), | 
|  | /* NOTE: short name, to work around driver model truncation of | 
|  | * "twl_regulator.12" (and friends) to "twl_regulator.1". | 
|  | */ | 
|  | .driver  = { | 
|  | .name  = "twl_reg", | 
|  | .owner = THIS_MODULE, | 
|  | .of_match_table = of_match_ptr(twl_of_match), | 
|  | }, | 
|  | }; | 
|  |  | 
|  | static int __init twlreg_init(void) | 
|  | { | 
|  | return platform_driver_register(&twlreg_driver); | 
|  | } | 
|  | subsys_initcall(twlreg_init); | 
|  |  | 
|  | static void __exit twlreg_exit(void) | 
|  | { | 
|  | platform_driver_unregister(&twlreg_driver); | 
|  | } | 
|  | module_exit(twlreg_exit) | 
|  |  | 
|  | MODULE_DESCRIPTION("TWL regulator driver"); | 
|  | MODULE_LICENSE("GPL"); |