| /* |
| * Common support for CompuLab CM-T3x CoMs |
| */ |
| |
| / { |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x10000000>; /* 256 MB */ |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&green_led_pins>; |
| ledb { |
| label = "cm-t3x:green"; |
| gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| /* HS USB Port 1 Power */ |
| hsusb1_power: hsusb1_power_reg { |
| compatible = "regulator-fixed"; |
| regulator-name = "hsusb1_vbus"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <70000>; |
| }; |
| |
| /* HS USB Port 2 Power */ |
| hsusb2_power: hsusb2_power_reg { |
| compatible = "regulator-fixed"; |
| regulator-name = "hsusb2_vbus"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <70000>; |
| }; |
| |
| /* HS USB Host PHY on PORT 1 */ |
| hsusb1_phy: hsusb1_phy { |
| compatible = "usb-nop-xceiv"; |
| vcc-supply = <&hsusb1_power>; |
| }; |
| |
| /* HS USB Host PHY on PORT 2 */ |
| hsusb2_phy: hsusb2_phy { |
| compatible = "usb-nop-xceiv"; |
| vcc-supply = <&hsusb2_power>; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ |
| OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ |
| >; |
| }; |
| |
| mmc1_pins: pinmux_mmc1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ |
| OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ |
| OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ |
| OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ |
| OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ |
| OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ |
| >; |
| }; |
| |
| green_led_pins: pinmux_green_led_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4) /* sys_clkout2.gpio_186 */ |
| >; |
| }; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| }; |
| |
| &mmc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| bus-width = <4>; |
| }; |
| |
| &mmc3 { |
| status = "disabled"; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| }; |
| &usbhshost { |
| port1-mode = "ehci-phy"; |
| port2-mode = "ehci-phy"; |
| }; |
| |
| &usbhsehci { |
| phys = <&hsusb1_phy &hsusb2_phy>; |
| }; |
