blob: 7b0a735562645cf042cfb312ace5018180d94559 [file] [log] [blame]
/*
* Xilinx Axi Ethernet device driver
*
* Copyright (c) 2008 Nissin Systems Co., Ltd., Yoshio Kashiwagi
* Copyright (c) 2005-2008 DLA Systems, David H. Lynch Jr. <dhlii@dlasys.net>
* Copyright (c) 2008-2009 Secret Lab Technologies Ltd.
* Copyright (c) 2010 - 2011 Michal Simek <monstr@monstr.eu>
* Copyright (c) 2010 - 2011 PetaLogix
* Copyright (c) 2010 - 2012 Xilinx, Inc. All rights reserved.
*
* This is a driver for the Xilinx Axi Ethernet which is used in the Virtex6
* and Spartan6.
*
* TODO:
* - Add Axi Fifo support.
* - Factor out Axi DMA code into separate driver.
* - Test and fix basic multicast filtering.
* - Add support for extended multicast filtering.
* - Test basic VLAN support.
* - Add support for extended VLAN support.
*/
#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/of_mdio.h>
#include <linux/of_platform.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/phy.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include "xilinx_axienet.h"
/* Descriptors defines for Tx and Rx DMA - 2^n for the best performance */
#define TX_BD_NUM 64
#define RX_BD_NUM 128
/* Must be shorter than length of ethtool_drvinfo.driver field to fit */
#define DRIVER_NAME "xaxienet"
#define DRIVER_DESCRIPTION "Xilinx Axi Ethernet driver"
#define DRIVER_VERSION "1.00a"
#define AXIENET_REGS_N 32
/* Match table for of_platform binding */
static struct of_device_id axienet_of_match[] = {
{ .compatible = "xlnx,axi-ethernet-1.00.a", },
{ .compatible = "xlnx,axi-ethernet-1.01.a", },
{ .compatible = "xlnx,axi-ethernet-2.01.a", },
{},
};
MODULE_DEVICE_TABLE(of, axienet_of_match);
/* Option table for setting up Axi Ethernet hardware options */
static struct axienet_option axienet_options[] = {
/* Turn on jumbo packet support for both Rx and Tx */
{
.opt = XAE_OPTION_JUMBO,
.reg = XAE_TC_OFFSET,
.m_or = XAE_TC_JUM_MASK,
}, {
.opt = XAE_OPTION_JUMBO,
.reg = XAE_RCW1_OFFSET,
.m_or = XAE_RCW1_JUM_MASK,
}, { /* Turn on VLAN packet support for both Rx and Tx */
.opt = XAE_OPTION_VLAN,
.reg = XAE_TC_OFFSET,
.m_or = XAE_TC_VLAN_MASK,
}, {
.opt = XAE_OPTION_VLAN,
.reg = XAE_RCW1_OFFSET,
.m_or = XAE_RCW1_VLAN_MASK,
}, { /* Turn on FCS stripping on receive packets */
.opt = XAE_OPTION_FCS_STRIP,
.reg = XAE_RCW1_OFFSET,
.m_or = XAE_RCW1_FCS_MASK,
}, { /* Turn on FCS insertion on transmit packets */
.opt = XAE_OPTION_FCS_INSERT,
.reg = XAE_TC_OFFSET,
.m_or = XAE_TC_FCS_MASK,
}, { /* Turn off length/type field checking on receive packets */
.opt = XAE_OPTION_LENTYPE_ERR,
.reg = XAE_RCW1_OFFSET,
.m_or = XAE_RCW1_LT_DIS_MASK,
}, { /* Turn on Rx flow control */
.opt = XAE_OPTION_FLOW_CONTROL,
.reg = XAE_FCC_OFFSET,
.m_or = XAE_FCC_FCRX_MASK,
}, { /* Turn on Tx flow control */
.opt = XAE_OPTION_FLOW_CONTROL,
.reg = XAE_FCC_OFFSET,
.m_or = XAE_FCC_FCTX_MASK,
}, { /* Turn on promiscuous frame filtering */
.opt = XAE_OPTION_PROMISC,
.reg = XAE_FMI_OFFSET,
.m_or = XAE_FMI_PM_MASK,
}, { /* Enable transmitter */
.opt = XAE_OPTION_TXEN,
.reg = XAE_TC_OFFSET,
.m_or = XAE_TC_TX_MASK,
}, { /* Enable receiver */
.opt = XAE_OPTION_RXEN,
.reg = XAE_RCW1_OFFSET,
.m_or = XAE_RCW1_RX_MASK,
},
{}
};
/**
* axienet_dma_in32 - Memory mapped Axi DMA register read
* @lp: Pointer to axienet local structure
* @reg: Address offset from the base address of the Axi DMA core
*
* returns: The contents of the Axi DMA register
*
* This function returns the contents of the corresponding Axi DMA register.
*/
static inline u32 axienet_dma_in32(struct axienet_local *lp, off_t reg)
{
return in_be32(lp->dma_regs + reg);
}
/**
* axienet_dma_out32 - Memory mapped Axi DMA register write.
* @lp: Pointer to axienet local structure
* @reg: Address offset from the base address of the Axi DMA core
* @value: Value to be written into the Axi DMA register
*
* This function writes the desired value into the corresponding Axi DMA
* register.
*/
static inline void axienet_dma_out32(struct axienet_local *lp,
off_t reg, u32 value)
{
out_be32((lp->dma_regs + reg), value);
}
/**
* axienet_dma_bd_release - Release buffer descriptor rings
* @ndev: Pointer to the net_device structure
*
* This function is used to release the descriptors allocated in
* axienet_dma_bd_init. axienet_dma_bd_release is called when Axi Ethernet
* driver stop api is called.
*/
static void axienet_dma_bd_release(struct net_device *ndev)
{
int i;
struct axienet_local *lp = netdev_priv(ndev);
for (i = 0; i < RX_BD_NUM; i++) {
dma_unmap_single(ndev->dev.parent, lp->rx_bd_v[i].phys,
lp->max_frm_size, DMA_FROM_DEVICE);
dev_kfree_skb((struct sk_buff *)
(lp->rx_bd_v[i].sw_id_offset));
}
if (lp->rx_bd_v) {
dma_free_coherent(ndev->dev.parent,
sizeof(*lp->rx_bd_v) * RX_BD_NUM,
lp->rx_bd_v,
lp->rx_bd_p);
}
if (lp->tx_bd_v) {
dma_free_coherent(ndev->dev.parent,
sizeof(*lp->tx_bd_v) * TX_BD_NUM,
lp->tx_bd_v,
lp->tx_bd_p);
}
}
/**
* axienet_dma_bd_init - Setup buffer descriptor rings for Axi DMA
* @ndev: Pointer to the net_device structure
*
* returns: 0, on success
* -ENOMEM, on failure
*
* This function is called to initialize the Rx and Tx DMA descriptor
* rings. This initializes the descriptors with required default values
* and is called when Axi Ethernet driver reset is called.
*/
static int axienet_dma_bd_init(struct net_device *ndev)
{
u32 cr;
int i;
struct sk_buff *skb;
struct axienet_local *lp = netdev_priv(ndev);
/* Reset the indexes which are used for accessing the BDs */
lp->tx_bd_ci = 0;
lp->tx_bd_tail = 0;
lp->rx_bd_ci = 0;
/*
* Allocate the Tx and Rx buffer descriptors.
*/
lp->tx_bd_v = dma_zalloc_coherent(ndev->dev.parent,
sizeof(*lp->tx_bd_v) * TX_BD_NUM,
&lp->tx_bd_p, GFP_KERNEL);
if (!lp->tx_bd_v)
goto out;
lp->rx_bd_v = dma_zalloc_coherent(ndev->dev.parent,
sizeof(*lp->rx_bd_v) * RX_BD_NUM,
&lp->rx_bd_p, GFP_KERNEL);
if (!lp->rx_bd_v)
goto out;
for (i = 0; i < TX_BD_NUM; i++) {
lp->tx_bd_v[i].next = lp->tx_bd_p +
sizeof(*lp->tx_bd_v) *
((i + 1) % TX_BD_NUM);
}
for (i = 0; i < RX_BD_NUM; i++) {
lp->rx_bd_v[i].next = lp->rx_bd_p +
sizeof(*lp->rx_bd_v) *
((i + 1) % RX_BD_NUM);
skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
if (!skb)
goto out;
lp->rx_bd_v[i].sw_id_offset = (u32) skb;
lp->rx_bd_v[i].phys = dma_map_single(ndev->dev.parent,
skb->data,
lp->max_frm_size,
DMA_FROM_DEVICE);
lp->rx_bd_v[i].cntrl = lp->max_frm_size;
}
/* Start updating the Rx channel control register */
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
/* Update the interrupt coalesce count */
cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
((lp->coalesce_count_rx) << XAXIDMA_COALESCE_SHIFT));
/* Update the delay timer count */
cr = ((cr & ~XAXIDMA_DELAY_MASK) |
(XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
/* Enable coalesce, delay timer and error interrupts */
cr |= XAXIDMA_IRQ_ALL_MASK;
/* Write to the Rx channel control register */
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
/* Start updating the Tx channel control register */
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
/* Update the interrupt coalesce count */
cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
((lp->coalesce_count_tx) << XAXIDMA_COALESCE_SHIFT));
/* Update the delay timer count */
cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
(XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
/* Enable coalesce, delay timer and error interrupts */
cr |= XAXIDMA_IRQ_ALL_MASK;
/* Write to the Tx channel control register */
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
/* Populate the tail pointer and bring the Rx Axi DMA engine out of
* halted state. This will make the Rx side ready for reception.*/
axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
/* Write to the RS (Run-stop) bit in the Tx channel control register.
* Tx channel is now ready to run. But only after we write to the
* tail pointer register that the Tx channel will start transmitting */
axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
return 0;
out:
axienet_dma_bd_release(ndev);
return -ENOMEM;
}
/**
* axienet_set_mac_address - Write the MAC address
* @ndev: Pointer to the net_device structure
* @address: 6 byte Address to be written as MAC address
*
* This function is called to initialize the MAC address of the Axi Ethernet
* core. It writes to the UAW0 and UAW1 registers of the core.
*/
static void axienet_set_mac_address(struct net_device *ndev, void *address)
{
struct axienet_local *lp = netdev_priv(ndev);
if (address)
memcpy(ndev->dev_addr, address, ETH_ALEN);
if (!is_valid_ether_addr(ndev->dev_addr))
eth_random_addr(ndev->dev_addr);
/* Set up unicast MAC address filter set its mac address */
axienet_iow(lp, XAE_UAW0_OFFSET,
(ndev->dev_addr[0]) |
(ndev->dev_addr[1] << 8) |
(ndev->dev_addr[2] << 16) |
(ndev->dev_addr[3] << 24));
axienet_iow(lp, XAE_UAW1_OFFSET,
(((axienet_ior(lp, XAE_UAW1_OFFSET)) &
~XAE_UAW1_UNICASTADDR_MASK) |
(ndev->dev_addr[4] |
(ndev->dev_addr[5] << 8))));
}
/**
* netdev_set_mac_address - Write the MAC address (from outside the driver)
* @ndev: Pointer to the net_device structure
* @p: 6 byte Address to be written as MAC address
*
* returns: 0 for all conditions. Presently, there is no failure case.
*
* This function is called to initialize the MAC address of the Axi Ethernet
* core. It calls the core specific axienet_set_mac_address. This is the
* function that goes into net_device_ops structure entry ndo_set_mac_address.
*/
static int netdev_set_mac_address(struct net_device *ndev, void *p)
{
struct sockaddr *addr = p;
axienet_set_mac_address(ndev, addr->sa_data);
return 0;
}
/**
* axienet_set_multicast_list - Prepare the multicast table
* @ndev: Pointer to the net_device structure
*
* This function is called to initialize the multicast table during
* initialization. The Axi Ethernet basic multicast support has a four-entry
* multicast table which is initialized here. Additionally this function
* goes into the net_device_ops structure entry ndo_set_multicast_list. This
* means whenever the multicast table entries need to be updated this
* function gets called.
*/
static void axienet_set_multicast_list(struct net_device *ndev)
{
int i;
u32 reg, af0reg, af1reg;
struct axienet_local *lp = netdev_priv(ndev);
if (ndev->flags & (IFF_ALLMULTI | IFF_PROMISC) ||
netdev_mc_count(ndev) > XAE_MULTICAST_CAM_TABLE_NUM) {
/* We must make the kernel realize we had to move into
* promiscuous mode. If it was a promiscuous mode request
* the flag is already set. If not we set it. */
ndev->flags |= IFF_PROMISC;
reg = axienet_ior(lp, XAE_FMI_OFFSET);
reg |= XAE_FMI_PM_MASK;
axienet_iow(lp, XAE_FMI_OFFSET, reg);
dev_info(&ndev->dev, "Promiscuous mode enabled.\n");
} else if (!netdev_mc_empty(ndev)) {
struct netdev_hw_addr *ha;
i = 0;
netdev_for_each_mc_addr(ha, ndev) {
if (i >= XAE_MULTICAST_CAM_TABLE_NUM)
break;
af0reg = (ha->addr[0]);
af0reg |= (ha->addr[1] << 8);
af0reg |= (ha->addr[2] << 16);
af0reg |= (ha->addr[3] << 24);
af1reg = (ha->addr[4]);
af1reg |= (ha->addr[5] << 8);
reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
reg |= i;
axienet_iow(lp, XAE_FMI_OFFSET, reg);
axienet_iow(lp, XAE_AF0_OFFSET, af0reg);
axienet_iow(lp, XAE_AF1_OFFSET, af1reg);
i++;
}
} else {
reg = axienet_ior(lp, XAE_FMI_OFFSET);
reg &= ~XAE_FMI_PM_MASK;
axienet_iow(lp, XAE_FMI_OFFSET, reg);
for (i = 0; i < XAE_MULTICAST_CAM_TABLE_NUM; i++) {
reg = axienet_ior(lp, XAE_FMI_OFFSET) & 0xFFFFFF00;
reg |= i;
axienet_iow(lp, XAE_FMI_OFFSET, reg);
axienet_iow(lp, XAE_AF0_OFFSET, 0);
axienet_iow(lp, XAE_AF1_OFFSET, 0);
}
dev_info(&ndev->dev, "Promiscuous mode disabled.\n");
}
}
/**
* axienet_setoptions - Set an Axi Ethernet option
* @ndev: Pointer to the net_device structure
* @options: Option to be enabled/disabled
*
* The Axi Ethernet core has multiple features which can be selectively turned
* on or off. The typical options could be jumbo frame option, basic VLAN
* option, promiscuous mode option etc. This function is used to set or clear
* these options in the Axi Ethernet hardware. This is done through
* axienet_option structure .
*/
static void axienet_setoptions(struct net_device *ndev, u32 options)
{
int reg;
struct axienet_local *lp = netdev_priv(ndev);
struct axienet_option *tp = &axienet_options[0];
while (tp->opt) {
reg = ((axienet_ior(lp, tp->reg)) & ~(tp->m_or));
if (options & tp->opt)
reg |= tp->m_or;
axienet_iow(lp, tp->reg, reg);
tp++;
}
lp->options |= options;
}
static void __axienet_device_reset(struct axienet_local *lp,
struct device *dev, off_t offset)
{
u32 timeout;
/* Reset Axi DMA. This would reset Axi Ethernet core as well. The reset
* process of Axi DMA takes a while to complete as all pending
* commands/transfers will be flushed or completed during this
* reset process. */
axienet_dma_out32(lp, offset, XAXIDMA_CR_RESET_MASK);
timeout = DELAY_OF_ONE_MILLISEC;
while (axienet_dma_in32(lp, offset) & XAXIDMA_CR_RESET_MASK) {
udelay(1);
if (--timeout == 0) {
dev_err(dev, "axienet_device_reset DMA "
"reset timeout!\n");
break;
}
}
}
/**
* axienet_device_reset - Reset and initialize the Axi Ethernet hardware.
* @ndev: Pointer to the net_device structure
*
* This function is called to reset and initialize the Axi Ethernet core. This
* is typically called during initialization. It does a reset of the Axi DMA
* Rx/Tx channels and initializes the Axi DMA BDs. Since Axi DMA reset lines
* areconnected to Axi Ethernet reset lines, this in turn resets the Axi
* Ethernet core. No separate hardware reset is done for the Axi Ethernet
* core.
*/
static void axienet_device_reset(struct net_device *ndev)
{
u32 axienet_status;
struct axienet_local *lp = netdev_priv(ndev);
__axienet_device_reset(lp, &ndev->dev, XAXIDMA_TX_CR_OFFSET);
__axienet_device_reset(lp, &ndev->dev, XAXIDMA_RX_CR_OFFSET);
lp->max_frm_size = XAE_MAX_VLAN_FRAME_SIZE;
lp->options &= (~XAE_OPTION_JUMBO);
if ((ndev->mtu > XAE_MTU) &&
(ndev->mtu <= XAE_JUMBO_MTU) &&
(lp->jumbo_support)) {
lp->max_frm_size = ndev->mtu + XAE_HDR_VLAN_SIZE +
XAE_TRL_SIZE;
lp->options |= XAE_OPTION_JUMBO;
}
if (axienet_dma_bd_init(ndev)) {
dev_err(&ndev->dev, "axienet_device_reset descriptor "
"allocation failed\n");
}
axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
axienet_status &= ~XAE_RCW1_RX_MASK;
axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
if (axienet_status & XAE_INT_RXRJECT_MASK)
axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
/* Sync default options with HW but leave receiver and
* transmitter disabled.*/
axienet_setoptions(ndev, lp->options &
~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
axienet_set_mac_address(ndev, NULL);
axienet_set_multicast_list(ndev);
axienet_setoptions(ndev, lp->options);
ndev->trans_start = jiffies;
}
/**
* axienet_adjust_link - Adjust the PHY link speed/duplex.
* @ndev: Pointer to the net_device structure
*
* This function is called to change the speed and duplex setting after
* auto negotiation is done by the PHY. This is the function that gets
* registered with the PHY interface through the "of_phy_connect" call.
*/
static void axienet_adjust_link(struct net_device *ndev)
{
u32 emmc_reg;
u32 link_state;
u32 setspeed = 1;
struct axienet_local *lp = netdev_priv(ndev);
struct phy_device *phy = lp->phy_dev;
link_state = phy->speed | (phy->duplex << 1) | phy->link;
if (lp->last_link != link_state) {
if ((phy->speed == SPEED_10) || (phy->speed == SPEED_100)) {
if (lp->phy_type == XAE_PHY_TYPE_1000BASE_X)
setspeed = 0;
} else {
if ((phy->speed == SPEED_1000) &&
(lp->phy_type == XAE_PHY_TYPE_MII))
setspeed = 0;
}
if (setspeed == 1) {
emmc_reg = axienet_ior(lp, XAE_EMMC_OFFSET);
emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK;
switch (phy->speed) {
case SPEED_1000:
emmc_reg |= XAE_EMMC_LINKSPD_1000;
break;
case SPEED_100:
emmc_reg |= XAE_EMMC_LINKSPD_100;
break;
case SPEED_10:
emmc_reg |= XAE_EMMC_LINKSPD_10;
break;
default:
dev_err(&ndev->dev, "Speed other than 10, 100 "
"or 1Gbps is not supported\n");
break;
}
axienet_iow(lp, XAE_EMMC_OFFSET, emmc_reg);
lp->last_link = link_state;
phy_print_status(phy);
} else {
dev_err(&ndev->dev, "Error setting Axi Ethernet "
"mac speed\n");
}
}
}
/**
* axienet_start_xmit_done - Invoked once a transmit is completed by the
* Axi DMA Tx channel.
* @ndev: Pointer to the net_device structure
*
* This function is invoked from the Axi DMA Tx isr to notify the completion
* of transmit operation. It clears fields in the corresponding Tx BDs and
* unmaps the corresponding buffer so that CPU can regain ownership of the
* buffer. It finally invokes "netif_wake_queue" to restart transmission if
* required.
*/
static void axienet_start_xmit_done(struct net_device *ndev)
{
u32 size = 0;
u32 packets = 0;
struct axienet_local *lp = netdev_priv(ndev);
struct axidma_bd *cur_p;
unsigned int status = 0;
cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
status = cur_p->status;
while (status & XAXIDMA_BD_STS_COMPLETE_MASK) {
dma_unmap_single(ndev->dev.parent, cur_p->phys,
(cur_p->cntrl & XAXIDMA_BD_CTRL_LENGTH_MASK),
DMA_TO_DEVICE);
if (cur_p->app4)
dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
/*cur_p->phys = 0;*/
cur_p->app0 = 0;
cur_p->app1 = 0;
cur_p->app2 = 0;
cur_p->app4 = 0;
cur_p->status = 0;
size += status & XAXIDMA_BD_STS_ACTUAL_LEN_MASK;
packets++;
++lp->tx_bd_ci;
lp->tx_bd_ci %= TX_BD_NUM;
cur_p = &lp->tx_bd_v[lp->tx_bd_ci];
status = cur_p->status;
}
ndev->stats.tx_packets += packets;
ndev->stats.tx_bytes += size;
netif_wake_queue(ndev);
}
/**
* axienet_check_tx_bd_space - Checks if a BD/group of BDs are currently busy
* @lp: Pointer to the axienet_local structure
* @num_frag: The number of BDs to check for
*
* returns: 0, on success
* NETDEV_TX_BUSY, if any of the descriptors are not free
*
* This function is invoked before BDs are allocated and transmission starts.
* This function returns 0 if a BD or group of BDs can be allocated for
* transmission. If the BD or any of the BDs are not free the function
* returns a busy status. This is invoked from axienet_start_xmit.
*/
static inline int axienet_check_tx_bd_space(struct axienet_local *lp,
int num_frag)
{
struct axidma_bd *cur_p;
cur_p = &lp->tx_bd_v[(lp->tx_bd_tail + num_frag) % TX_BD_NUM];
if (cur_p->status & XAXIDMA_BD_STS_ALL_MASK)
return NETDEV_TX_BUSY;
return 0;
}
/**
* axienet_start_xmit - Starts the transmission.
* @skb: sk_buff pointer that contains data to be Txed.
* @ndev: Pointer to net_device structure.
*
* returns: NETDEV_TX_OK, on success
* NETDEV_TX_BUSY, if any of the descriptors are not free
*
* This function is invoked from upper layers to initiate transmission. The
* function uses the next available free BDs and populates their fields to
* start the transmission. Additionally if checksum offloading is supported,
* it populates AXI Stream Control fields with appropriate values.
*/
static int axienet_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
u32 ii;
u32 num_frag;
u32 csum_start_off;
u32 csum_index_off;
skb_frag_t *frag;
dma_addr_t tail_p;
struct axienet_local *lp = netdev_priv(ndev);
struct axidma_bd *cur_p;
num_frag = skb_shinfo(skb)->nr_frags;
cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
if (axienet_check_tx_bd_space(lp, num_frag)) {
if (!netif_queue_stopped(ndev))
netif_stop_queue(ndev);
return NETDEV_TX_BUSY;
}
if (skb->ip_summed == CHECKSUM_PARTIAL) {
if (lp->features & XAE_FEATURE_FULL_TX_CSUM) {
/* Tx Full Checksum Offload Enabled */
cur_p->app0 |= 2;
} else if (lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) {
csum_start_off = skb_transport_offset(skb);
csum_index_off = csum_start_off + skb->csum_offset;
/* Tx Partial Checksum Offload Enabled */
cur_p->app0 |= 1;
cur_p->app1 = (csum_start_off << 16) | csum_index_off;
}
} else if (skb->ip_summed == CHECKSUM_UNNECESSARY) {
cur_p->app0 |= 2; /* Tx Full Checksum Offload Enabled */
}
cur_p->cntrl = skb_headlen(skb) | XAXIDMA_BD_CTRL_TXSOF_MASK;
cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
skb_headlen(skb), DMA_TO_DEVICE);
for (ii = 0; ii < num_frag; ii++) {
++lp->tx_bd_tail;
lp->tx_bd_tail %= TX_BD_NUM;
cur_p = &lp->tx_bd_v[lp->tx_bd_tail];
frag = &skb_shinfo(skb)->frags[ii];
cur_p->phys = dma_map_single(ndev->dev.parent,
skb_frag_address(frag),
skb_frag_size(frag),
DMA_TO_DEVICE);
cur_p->cntrl = skb_frag_size(frag);
}
cur_p->cntrl |= XAXIDMA_BD_CTRL_TXEOF_MASK;
cur_p->app4 = (unsigned long)skb;
tail_p = lp->tx_bd_p + sizeof(*lp->tx_bd_v) * lp->tx_bd_tail;
/* Start the transfer */
axienet_dma_out32(lp, XAXIDMA_TX_TDESC_OFFSET, tail_p);
++lp->tx_bd_tail;
lp->tx_bd_tail %= TX_BD_NUM;
return NETDEV_TX_OK;
}
/**
* axienet_recv - Is called from Axi DMA Rx Isr to complete the received
* BD processing.
* @ndev: Pointer to net_device structure.
*
* This function is invoked from the Axi DMA Rx isr to process the Rx BDs. It
* does minimal processing and invokes "netif_rx" to complete further
* processing.
*/
static void axienet_recv(struct net_device *ndev)
{
u32 length;
u32 csumstatus;
u32 size = 0;
u32 packets = 0;
dma_addr_t tail_p;
struct axienet_local *lp = netdev_priv(ndev);
struct sk_buff *skb, *new_skb;
struct axidma_bd *cur_p;
tail_p = lp->rx_bd_p + sizeof(*lp->rx_bd_v) * lp->rx_bd_ci;
cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
while ((cur_p->status & XAXIDMA_BD_STS_COMPLETE_MASK)) {
skb = (struct sk_buff *) (cur_p->sw_id_offset);
length = cur_p->app4 & 0x0000FFFF;
dma_unmap_single(ndev->dev.parent, cur_p->phys,
lp->max_frm_size,
DMA_FROM_DEVICE);
skb_put(skb, length);
skb->protocol = eth_type_trans(skb, ndev);
/*skb_checksum_none_assert(skb);*/
skb->ip_summed = CHECKSUM_NONE;
/* if we're doing Rx csum offload, set it up */
if (lp->features & XAE_FEATURE_FULL_RX_CSUM) {
csumstatus = (cur_p->app2 &
XAE_FULL_CSUM_STATUS_MASK) >> 3;
if ((csumstatus == XAE_IP_TCP_CSUM_VALIDATED) ||
(csumstatus == XAE_IP_UDP_CSUM_VALIDATED)) {
skb->ip_summed = CHECKSUM_UNNECESSARY;
}
} else if ((lp->features & XAE_FEATURE_PARTIAL_RX_CSUM) != 0 &&
skb->protocol == htons(ETH_P_IP) &&
skb->len > 64) {
skb->csum = be32_to_cpu(cur_p->app3 & 0xFFFF);
skb->ip_summed = CHECKSUM_COMPLETE;
}
netif_rx(skb);
size += length;
packets++;
new_skb = netdev_alloc_skb_ip_align(ndev, lp->max_frm_size);
if (!new_skb)
return;
cur_p->phys = dma_map_single(ndev->dev.parent, new_skb->data,
lp->max_frm_size,
DMA_FROM_DEVICE);
cur_p->cntrl = lp->max_frm_size;
cur_p->status = 0;
cur_p->sw_id_offset = (u32) new_skb;
++lp->rx_bd_ci;
lp->rx_bd_ci %= RX_BD_NUM;
cur_p = &lp->rx_bd_v[lp->rx_bd_ci];
}
ndev->stats.rx_packets += packets;
ndev->stats.rx_bytes += size;
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, tail_p);
}
/**
* axienet_tx_irq - Tx Done Isr.
* @irq: irq number
* @_ndev: net_device pointer
*
* returns: IRQ_HANDLED for all cases.
*
* This is the Axi DMA Tx done Isr. It invokes "axienet_start_xmit_done"
* to complete the BD processing.
*/
static irqreturn_t axienet_tx_irq(int irq, void *_ndev)
{
u32 cr;
unsigned int status;
struct net_device *ndev = _ndev;
struct axienet_local *lp = netdev_priv(ndev);
status = axienet_dma_in32(lp, XAXIDMA_TX_SR_OFFSET);
if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
axienet_start_xmit_done(lp->ndev);
goto out;
}
if (!(status & XAXIDMA_IRQ_ALL_MASK))
dev_err(&ndev->dev, "No interrupts asserted in Tx path");
if (status & XAXIDMA_IRQ_ERROR_MASK) {
dev_err(&ndev->dev, "DMA Tx error 0x%x\n", status);
dev_err(&ndev->dev, "Current BD is at: 0x%x\n",
(lp->tx_bd_v[lp->tx_bd_ci]).phys);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
/* Disable coalesce, delay timer and error interrupts */
cr &= (~XAXIDMA_IRQ_ALL_MASK);
/* Write to the Tx channel control register */
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
/* Disable coalesce, delay timer and error interrupts */
cr &= (~XAXIDMA_IRQ_ALL_MASK);
/* Write to the Rx channel control register */
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
tasklet_schedule(&lp->dma_err_tasklet);
}
out:
axienet_dma_out32(lp, XAXIDMA_TX_SR_OFFSET, status);
return IRQ_HANDLED;
}
/**
* axienet_rx_irq - Rx Isr.
* @irq: irq number
* @_ndev: net_device pointer
*
* returns: IRQ_HANDLED for all cases.
*
* This is the Axi DMA Rx Isr. It invokes "axienet_recv" to complete the BD
* processing.
*/
static irqreturn_t axienet_rx_irq(int irq, void *_ndev)
{
u32 cr;
unsigned int status;
struct net_device *ndev = _ndev;
struct axienet_local *lp = netdev_priv(ndev);
status = axienet_dma_in32(lp, XAXIDMA_RX_SR_OFFSET);
if (status & (XAXIDMA_IRQ_IOC_MASK | XAXIDMA_IRQ_DELAY_MASK)) {
axienet_recv(lp->ndev);
goto out;
}
if (!(status & XAXIDMA_IRQ_ALL_MASK))
dev_err(&ndev->dev, "No interrupts asserted in Rx path");
if (status & XAXIDMA_IRQ_ERROR_MASK) {
dev_err(&ndev->dev, "DMA Rx error 0x%x\n", status);
dev_err(&ndev->dev, "Current BD is at: 0x%x\n",
(lp->rx_bd_v[lp->rx_bd_ci]).phys);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
/* Disable coalesce, delay timer and error interrupts */
cr &= (~XAXIDMA_IRQ_ALL_MASK);
/* Finally write to the Tx channel control register */
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
/* Disable coalesce, delay timer and error interrupts */
cr &= (~XAXIDMA_IRQ_ALL_MASK);
/* write to the Rx channel control register */
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
tasklet_schedule(&lp->dma_err_tasklet);
}
out:
axienet_dma_out32(lp, XAXIDMA_RX_SR_OFFSET, status);
return IRQ_HANDLED;
}
static void axienet_dma_err_handler(unsigned long data);
/**
* axienet_open - Driver open routine.
* @ndev: Pointer to net_device structure
*
* returns: 0, on success.
* -ENODEV, if PHY cannot be connected to
* non-zero error value on failure
*
* This is the driver open routine. It calls phy_start to start the PHY device.
* It also allocates interrupt service routines, enables the interrupt lines
* and ISR handling. Axi Ethernet core is reset through Axi DMA core. Buffer
* descriptors are initialized.
*/
static int axienet_open(struct net_device *ndev)
{
int ret, mdio_mcreg;
struct axienet_local *lp = netdev_priv(ndev);
dev_dbg(&ndev->dev, "axienet_open()\n");
mdio_mcreg = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
ret = axienet_mdio_wait_until_ready(lp);
if (ret < 0)
return ret;
/* Disable the MDIO interface till Axi Ethernet Reset is completed.
* When we do an Axi Ethernet reset, it resets the complete core
* including the MDIO. If MDIO is not disabled when the reset
* process is started, MDIO will be broken afterwards. */
axienet_iow(lp, XAE_MDIO_MC_OFFSET,
(mdio_mcreg & (~XAE_MDIO_MC_MDIOEN_MASK)));
axienet_device_reset(ndev);
/* Enable the MDIO */
axienet_iow(lp, XAE_MDIO_MC_OFFSET, mdio_mcreg);
ret = axienet_mdio_wait_until_ready(lp);
if (ret < 0)
return ret;
if (lp->phy_node) {
lp->phy_dev = of_phy_connect(lp->ndev, lp->phy_node,
axienet_adjust_link, 0,
PHY_INTERFACE_MODE_GMII);
if (!lp->phy_dev) {
dev_err(lp->dev, "of_phy_connect() failed\n");
return -ENODEV;
}
phy_start(lp->phy_dev);
}
/* Enable tasklets for Axi DMA error handling */
tasklet_init(&lp->dma_err_tasklet, axienet_dma_err_handler,
(unsigned long) lp);
/* Enable interrupts for Axi DMA Tx */
ret = request_irq(lp->tx_irq, axienet_tx_irq, 0, ndev->name, ndev);
if (ret)
goto err_tx_irq;
/* Enable interrupts for Axi DMA Rx */
ret = request_irq(lp->rx_irq, axienet_rx_irq, 0, ndev->name, ndev);
if (ret)
goto err_rx_irq;
return 0;
err_rx_irq:
free_irq(lp->tx_irq, ndev);
err_tx_irq:
if (lp->phy_dev)
phy_disconnect(lp->phy_dev);
lp->phy_dev = NULL;
tasklet_kill(&lp->dma_err_tasklet);
dev_err(lp->dev, "request_irq() failed\n");
return ret;
}
/**
* axienet_stop - Driver stop routine.
* @ndev: Pointer to net_device structure
*
* returns: 0, on success.
*
* This is the driver stop routine. It calls phy_disconnect to stop the PHY
* device. It also removes the interrupt handlers and disables the interrupts.
* The Axi DMA Tx/Rx BDs are released.
*/
static int axienet_stop(struct net_device *ndev)
{
u32 cr;
struct axienet_local *lp = netdev_priv(ndev);
dev_dbg(&ndev->dev, "axienet_close()\n");
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
cr & (~XAXIDMA_CR_RUNSTOP_MASK));
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
cr & (~XAXIDMA_CR_RUNSTOP_MASK));
axienet_setoptions(ndev, lp->options &
~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
tasklet_kill(&lp->dma_err_tasklet);
free_irq(lp->tx_irq, ndev);
free_irq(lp->rx_irq, ndev);
if (lp->phy_dev)
phy_disconnect(lp->phy_dev);
lp->phy_dev = NULL;
axienet_dma_bd_release(ndev);
return 0;
}
/**
* axienet_change_mtu - Driver change mtu routine.
* @ndev: Pointer to net_device structure
* @new_mtu: New mtu value to be applied
*
* returns: Always returns 0 (success).
*
* This is the change mtu driver routine. It checks if the Axi Ethernet
* hardware supports jumbo frames before changing the mtu. This can be
* called only when the device is not up.
*/
static int axienet_change_mtu(struct net_device *ndev, int new_mtu)
{
struct axienet_local *lp = netdev_priv(ndev);
if (netif_running(ndev))
return -EBUSY;
if (lp->jumbo_support) {
if ((new_mtu > XAE_JUMBO_MTU) || (new_mtu < 64))
return -EINVAL;
ndev->mtu = new_mtu;
} else {
if ((new_mtu > XAE_MTU) || (new_mtu < 64))
return -EINVAL;
ndev->mtu = new_mtu;
}
return 0;
}
#ifdef CONFIG_NET_POLL_CONTROLLER
/**
* axienet_poll_controller - Axi Ethernet poll mechanism.
* @ndev: Pointer to net_device structure
*
* This implements Rx/Tx ISR poll mechanisms. The interrupts are disabled prior
* to polling the ISRs and are enabled back after the polling is done.
*/
static void axienet_poll_controller(struct net_device *ndev)
{
struct axienet_local *lp = netdev_priv(ndev);
disable_irq(lp->tx_irq);
disable_irq(lp->rx_irq);
axienet_rx_irq(lp->tx_irq, ndev);
axienet_tx_irq(lp->rx_irq, ndev);
enable_irq(lp->tx_irq);
enable_irq(lp->rx_irq);
}
#endif
static const struct net_device_ops axienet_netdev_ops = {
.ndo_open = axienet_open,
.ndo_stop = axienet_stop,
.ndo_start_xmit = axienet_start_xmit,
.ndo_change_mtu = axienet_change_mtu,
.ndo_set_mac_address = netdev_set_mac_address,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_rx_mode = axienet_set_multicast_list,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_poll_controller = axienet_poll_controller,
#endif
};
/**
* axienet_ethtools_get_settings - Get Axi Ethernet settings related to PHY.
* @ndev: Pointer to net_device structure
* @ecmd: Pointer to ethtool_cmd structure
*
* This implements ethtool command for getting PHY settings. If PHY could
* not be found, the function returns -ENODEV. This function calls the
* relevant PHY ethtool API to get the PHY settings.
* Issue "ethtool ethX" under linux prompt to execute this function.
*/
static int axienet_ethtools_get_settings(struct net_device *ndev,
struct ethtool_cmd *ecmd)
{
struct axienet_local *lp = netdev_priv(ndev);
struct phy_device *phydev = lp->phy_dev;
if (!phydev)
return -ENODEV;
return phy_ethtool_gset(phydev, ecmd);
}
/**
* axienet_ethtools_set_settings - Set PHY settings as passed in the argument.
* @ndev: Pointer to net_device structure
* @ecmd: Pointer to ethtool_cmd structure
*
* This implements ethtool command for setting various PHY settings. If PHY
* could not be found, the function returns -ENODEV. This function calls the
* relevant PHY ethtool API to set the PHY.
* Issue e.g. "ethtool -s ethX speed 1000" under linux prompt to execute this
* function.
*/
static int axienet_ethtools_set_settings(struct net_device *ndev,
struct ethtool_cmd *ecmd)
{
struct axienet_local *lp = netdev_priv(ndev);
struct phy_device *phydev = lp->phy_dev;
if (!phydev)
return -ENODEV;
return phy_ethtool_sset(phydev, ecmd);
}
/**
* axienet_ethtools_get_drvinfo - Get various Axi Ethernet driver information.
* @ndev: Pointer to net_device structure
* @ed: Pointer to ethtool_drvinfo structure
*
* This implements ethtool command for getting the driver information.
* Issue "ethtool -i ethX" under linux prompt to execute this function.
*/
static void axienet_ethtools_get_drvinfo(struct net_device *ndev,
struct ethtool_drvinfo *ed)
{
strlcpy(ed->driver, DRIVER_NAME, sizeof(ed->driver));
strlcpy(ed->version, DRIVER_VERSION, sizeof(ed->version));
ed->regdump_len = sizeof(u32) * AXIENET_REGS_N;
}
/**
* axienet_ethtools_get_regs_len - Get the total regs length present in the
* AxiEthernet core.
* @ndev: Pointer to net_device structure
*
* This implements ethtool command for getting the total register length
* information.
*/
static int axienet_ethtools_get_regs_len(struct net_device *ndev)
{
return sizeof(u32) * AXIENET_REGS_N;
}
/**
* axienet_ethtools_get_regs - Dump the contents of all registers present
* in AxiEthernet core.
* @ndev: Pointer to net_device structure
* @regs: Pointer to ethtool_regs structure
* @ret: Void pointer used to return the contents of the registers.
*
* This implements ethtool command for getting the Axi Ethernet register dump.
* Issue "ethtool -d ethX" to execute this function.
*/
static void axienet_ethtools_get_regs(struct net_device *ndev,
struct ethtool_regs *regs, void *ret)
{
u32 *data = (u32 *) ret;
size_t len = sizeof(u32) * AXIENET_REGS_N;
struct axienet_local *lp = netdev_priv(ndev);
regs->version = 0;
regs->len = len;
memset(data, 0, len);
data[0] = axienet_ior(lp, XAE_RAF_OFFSET);
data[1] = axienet_ior(lp, XAE_TPF_OFFSET);
data[2] = axienet_ior(lp, XAE_IFGP_OFFSET);
data[3] = axienet_ior(lp, XAE_IS_OFFSET);
data[4] = axienet_ior(lp, XAE_IP_OFFSET);
data[5] = axienet_ior(lp, XAE_IE_OFFSET);
data[6] = axienet_ior(lp, XAE_TTAG_OFFSET);
data[7] = axienet_ior(lp, XAE_RTAG_OFFSET);
data[8] = axienet_ior(lp, XAE_UAWL_OFFSET);
data[9] = axienet_ior(lp, XAE_UAWU_OFFSET);
data[10] = axienet_ior(lp, XAE_TPID0_OFFSET);
data[11] = axienet_ior(lp, XAE_TPID1_OFFSET);
data[12] = axienet_ior(lp, XAE_PPST_OFFSET);
data[13] = axienet_ior(lp, XAE_RCW0_OFFSET);
data[14] = axienet_ior(lp, XAE_RCW1_OFFSET);
data[15] = axienet_ior(lp, XAE_TC_OFFSET);
data[16] = axienet_ior(lp, XAE_FCC_OFFSET);
data[17] = axienet_ior(lp, XAE_EMMC_OFFSET);
data[18] = axienet_ior(lp, XAE_PHYC_OFFSET);
data[19] = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
data[20] = axienet_ior(lp, XAE_MDIO_MCR_OFFSET);
data[21] = axienet_ior(lp, XAE_MDIO_MWD_OFFSET);
data[22] = axienet_ior(lp, XAE_MDIO_MRD_OFFSET);
data[23] = axienet_ior(lp, XAE_MDIO_MIS_OFFSET);
data[24] = axienet_ior(lp, XAE_MDIO_MIP_OFFSET);
data[25] = axienet_ior(lp, XAE_MDIO_MIE_OFFSET);
data[26] = axienet_ior(lp, XAE_MDIO_MIC_OFFSET);
data[27] = axienet_ior(lp, XAE_UAW0_OFFSET);
data[28] = axienet_ior(lp, XAE_UAW1_OFFSET);
data[29] = axienet_ior(lp, XAE_FMI_OFFSET);
data[30] = axienet_ior(lp, XAE_AF0_OFFSET);
data[31] = axienet_ior(lp, XAE_AF1_OFFSET);
}
/**
* axienet_ethtools_get_pauseparam - Get the pause parameter setting for
* Tx and Rx paths.
* @ndev: Pointer to net_device structure
* @epauseparm: Pointer to ethtool_pauseparam structure.
*
* This implements ethtool command for getting axi ethernet pause frame
* setting. Issue "ethtool -a ethX" to execute this function.
*/
static void
axienet_ethtools_get_pauseparam(struct net_device *ndev,
struct ethtool_pauseparam *epauseparm)
{
u32 regval;
struct axienet_local *lp = netdev_priv(ndev);
epauseparm->autoneg = 0;
regval = axienet_ior(lp, XAE_FCC_OFFSET);
epauseparm->tx_pause = regval & XAE_FCC_FCTX_MASK;
epauseparm->rx_pause = regval & XAE_FCC_FCRX_MASK;
}
/**
* axienet_ethtools_set_pauseparam - Set device pause parameter(flow control)
* settings.
* @ndev: Pointer to net_device structure
* @epauseparam:Pointer to ethtool_pauseparam structure
*
* This implements ethtool command for enabling flow control on Rx and Tx
* paths. Issue "ethtool -A ethX tx on|off" under linux prompt to execute this
* function.
*/
static int
axienet_ethtools_set_pauseparam(struct net_device *ndev,
struct ethtool_pauseparam *epauseparm)
{
u32 regval = 0;
struct axienet_local *lp = netdev_priv(ndev);
if (netif_running(ndev)) {
printk(KERN_ERR "%s: Please stop netif before applying "
"configruation\n", ndev->name);
return -EFAULT;
}
regval = axienet_ior(lp, XAE_FCC_OFFSET);
if (epauseparm->tx_pause)
regval |= XAE_FCC_FCTX_MASK;
else
regval &= ~XAE_FCC_FCTX_MASK;
if (epauseparm->rx_pause)
regval |= XAE_FCC_FCRX_MASK;
else
regval &= ~XAE_FCC_FCRX_MASK;
axienet_iow(lp, XAE_FCC_OFFSET, regval);
return 0;
}
/**
* axienet_ethtools_get_coalesce - Get DMA interrupt coalescing count.
* @ndev: Pointer to net_device structure
* @ecoalesce: Pointer to ethtool_coalesce structure
*
* This implements ethtool command for getting the DMA interrupt coalescing
* count on Tx and Rx paths. Issue "ethtool -c ethX" under linux prompt to
* execute this function.
*/
static int axienet_ethtools_get_coalesce(struct net_device *ndev,
struct ethtool_coalesce *ecoalesce)
{
u32 regval = 0;
struct axienet_local *lp = netdev_priv(ndev);
regval = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
ecoalesce->rx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
>> XAXIDMA_COALESCE_SHIFT;
regval = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
ecoalesce->tx_max_coalesced_frames = (regval & XAXIDMA_COALESCE_MASK)
>> XAXIDMA_COALESCE_SHIFT;
return 0;
}
/**
* axienet_ethtools_set_coalesce - Set DMA interrupt coalescing count.
* @ndev: Pointer to net_device structure
* @ecoalesce: Pointer to ethtool_coalesce structure
*
* This implements ethtool command for setting the DMA interrupt coalescing
* count on Tx and Rx paths. Issue "ethtool -C ethX rx-frames 5" under linux
* prompt to execute this function.
*/
static int axienet_ethtools_set_coalesce(struct net_device *ndev,
struct ethtool_coalesce *ecoalesce)
{
struct axienet_local *lp = netdev_priv(ndev);
if (netif_running(ndev)) {
printk(KERN_ERR "%s: Please stop netif before applying "
"configruation\n", ndev->name);
return -EFAULT;
}
if ((ecoalesce->rx_coalesce_usecs) ||
(ecoalesce->rx_coalesce_usecs_irq) ||
(ecoalesce->rx_max_coalesced_frames_irq) ||
(ecoalesce->tx_coalesce_usecs) ||
(ecoalesce->tx_coalesce_usecs_irq) ||
(ecoalesce->tx_max_coalesced_frames_irq) ||
(ecoalesce->stats_block_coalesce_usecs) ||
(ecoalesce->use_adaptive_rx_coalesce) ||
(ecoalesce->use_adaptive_tx_coalesce) ||
(ecoalesce->pkt_rate_low) ||
(ecoalesce->rx_coalesce_usecs_low) ||
(ecoalesce->rx_max_coalesced_frames_low) ||
(ecoalesce->tx_coalesce_usecs_low) ||
(ecoalesce->tx_max_coalesced_frames_low) ||
(ecoalesce->pkt_rate_high) ||
(ecoalesce->rx_coalesce_usecs_high) ||
(ecoalesce->rx_max_coalesced_frames_high) ||
(ecoalesce->tx_coalesce_usecs_high) ||
(ecoalesce->tx_max_coalesced_frames_high) ||
(ecoalesce->rate_sample_interval))
return -EOPNOTSUPP;
if (ecoalesce->rx_max_coalesced_frames)
lp->coalesce_count_rx = ecoalesce->rx_max_coalesced_frames;
if (ecoalesce->tx_max_coalesced_frames)
lp->coalesce_count_tx = ecoalesce->tx_max_coalesced_frames;
return 0;
}
static struct ethtool_ops axienet_ethtool_ops = {
.get_settings = axienet_ethtools_get_settings,
.set_settings = axienet_ethtools_set_settings,
.get_drvinfo = axienet_ethtools_get_drvinfo,
.get_regs_len = axienet_ethtools_get_regs_len,
.get_regs = axienet_ethtools_get_regs,
.get_link = ethtool_op_get_link,
.get_pauseparam = axienet_ethtools_get_pauseparam,
.set_pauseparam = axienet_ethtools_set_pauseparam,
.get_coalesce = axienet_ethtools_get_coalesce,
.set_coalesce = axienet_ethtools_set_coalesce,
};
/**
* axienet_dma_err_handler - Tasklet handler for Axi DMA Error
* @data: Data passed
*
* Resets the Axi DMA and Axi Ethernet devices, and reconfigures the
* Tx/Rx BDs.
*/
static void axienet_dma_err_handler(unsigned long data)
{
u32 axienet_status;
u32 cr, i;
int mdio_mcreg;
struct axienet_local *lp = (struct axienet_local *) data;
struct net_device *ndev = lp->ndev;
struct axidma_bd *cur_p;
axienet_setoptions(ndev, lp->options &
~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
mdio_mcreg = axienet_ior(lp, XAE_MDIO_MC_OFFSET);
axienet_mdio_wait_until_ready(lp);
/* Disable the MDIO interface till Axi Ethernet Reset is completed.
* When we do an Axi Ethernet reset, it resets the complete core
* including the MDIO. So if MDIO is not disabled when the reset
* process is started, MDIO will be broken afterwards. */
axienet_iow(lp, XAE_MDIO_MC_OFFSET, (mdio_mcreg &
~XAE_MDIO_MC_MDIOEN_MASK));
__axienet_device_reset(lp, &ndev->dev, XAXIDMA_TX_CR_OFFSET);
__axienet_device_reset(lp, &ndev->dev, XAXIDMA_RX_CR_OFFSET);
axienet_iow(lp, XAE_MDIO_MC_OFFSET, mdio_mcreg);
axienet_mdio_wait_until_ready(lp);
for (i = 0; i < TX_BD_NUM; i++) {
cur_p = &lp->tx_bd_v[i];
if (cur_p->phys)
dma_unmap_single(ndev->dev.parent, cur_p->phys,
(cur_p->cntrl &
XAXIDMA_BD_CTRL_LENGTH_MASK),
DMA_TO_DEVICE);
if (cur_p->app4)
dev_kfree_skb_irq((struct sk_buff *) cur_p->app4);
cur_p->phys = 0;
cur_p->cntrl = 0;
cur_p->status = 0;
cur_p->app0 = 0;
cur_p->app1 = 0;
cur_p->app2 = 0;
cur_p->app3 = 0;
cur_p->app4 = 0;
cur_p->sw_id_offset = 0;
}
for (i = 0; i < RX_BD_NUM; i++) {
cur_p = &lp->rx_bd_v[i];
cur_p->status = 0;
cur_p->app0 = 0;
cur_p->app1 = 0;
cur_p->app2 = 0;
cur_p->app3 = 0;
cur_p->app4 = 0;
}
lp->tx_bd_ci = 0;
lp->tx_bd_tail = 0;
lp->rx_bd_ci = 0;
/* Start updating the Rx channel control register */
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
/* Update the interrupt coalesce count */
cr = ((cr & ~XAXIDMA_COALESCE_MASK) |
(XAXIDMA_DFT_RX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
/* Update the delay timer count */
cr = ((cr & ~XAXIDMA_DELAY_MASK) |
(XAXIDMA_DFT_RX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
/* Enable coalesce, delay timer and error interrupts */
cr |= XAXIDMA_IRQ_ALL_MASK;
/* Finally write to the Rx channel control register */
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET, cr);
/* Start updating the Tx channel control register */
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
/* Update the interrupt coalesce count */
cr = (((cr & ~XAXIDMA_COALESCE_MASK)) |
(XAXIDMA_DFT_TX_THRESHOLD << XAXIDMA_COALESCE_SHIFT));
/* Update the delay timer count */
cr = (((cr & ~XAXIDMA_DELAY_MASK)) |
(XAXIDMA_DFT_TX_WAITBOUND << XAXIDMA_DELAY_SHIFT));
/* Enable coalesce, delay timer and error interrupts */
cr |= XAXIDMA_IRQ_ALL_MASK;
/* Finally write to the Tx channel control register */
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET, cr);
/* Populate the tail pointer and bring the Rx Axi DMA engine out of
* halted state. This will make the Rx side ready for reception.*/
axienet_dma_out32(lp, XAXIDMA_RX_CDESC_OFFSET, lp->rx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_RX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_RX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
axienet_dma_out32(lp, XAXIDMA_RX_TDESC_OFFSET, lp->rx_bd_p +
(sizeof(*lp->rx_bd_v) * (RX_BD_NUM - 1)));
/* Write to the RS (Run-stop) bit in the Tx channel control register.
* Tx channel is now ready to run. But only after we write to the
* tail pointer register that the Tx channel will start transmitting */
axienet_dma_out32(lp, XAXIDMA_TX_CDESC_OFFSET, lp->tx_bd_p);
cr = axienet_dma_in32(lp, XAXIDMA_TX_CR_OFFSET);
axienet_dma_out32(lp, XAXIDMA_TX_CR_OFFSET,
cr | XAXIDMA_CR_RUNSTOP_MASK);
axienet_status = axienet_ior(lp, XAE_RCW1_OFFSET);
axienet_status &= ~XAE_RCW1_RX_MASK;
axienet_iow(lp, XAE_RCW1_OFFSET, axienet_status);
axienet_status = axienet_ior(lp, XAE_IP_OFFSET);
if (axienet_status & XAE_INT_RXRJECT_MASK)
axienet_iow(lp, XAE_IS_OFFSET, XAE_INT_RXRJECT_MASK);
axienet_iow(lp, XAE_FCC_OFFSET, XAE_FCC_FCRX_MASK);
/* Sync default options with HW but leave receiver and
* transmitter disabled.*/
axienet_setoptions(ndev, lp->options &
~(XAE_OPTION_TXEN | XAE_OPTION_RXEN));
axienet_set_mac_address(ndev, NULL);
axienet_set_multicast_list(ndev);
axienet_setoptions(ndev, lp->options);
}
/**
* axienet_of_probe - Axi Ethernet probe function.
* @op: Pointer to platform device structure.
* @match: Pointer to device id structure
*
* returns: 0, on success
* Non-zero error value on failure.
*
* This is the probe routine for Axi Ethernet driver. This is called before
* any other driver routines are invoked. It allocates and sets up the Ethernet
* device. Parses through device tree and populates fields of
* axienet_local. It registers the Ethernet device.
*/
static int axienet_of_probe(struct platform_device *op)
{
__be32 *p;
int size, ret = 0;
struct device_node *np;
struct axienet_local *lp;
struct net_device *ndev;
const void *addr;
ndev = alloc_etherdev(sizeof(*lp));
if (!ndev)
return -ENOMEM;
ether_setup(ndev);
platform_set_drvdata(op, ndev);
SET_NETDEV_DEV(ndev, &op->dev);
ndev->flags &= ~IFF_MULTICAST; /* clear multicast */
ndev->features = NETIF_F_SG;
ndev->netdev_ops = &axienet_netdev_ops;
ndev->ethtool_ops = &axienet_ethtool_ops;
lp = netdev_priv(ndev);
lp->ndev = ndev;
lp->dev = &op->dev;
lp->options = XAE_OPTION_DEFAULTS;
/* Map device registers */
lp->regs = of_iomap(op->dev.of_node, 0);
if (!lp->regs) {
dev_err(&op->dev, "could not map Axi Ethernet regs.\n");
goto nodev;
}
/* Setup checksum offload, but default to off if not specified */
lp->features = 0;
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,txcsum", NULL);
if (p) {
switch (be32_to_cpup(p)) {
case 1:
lp->csum_offload_on_tx_path =
XAE_FEATURE_PARTIAL_TX_CSUM;
lp->features |= XAE_FEATURE_PARTIAL_TX_CSUM;
/* Can checksum TCP/UDP over IPv4. */
ndev->features |= NETIF_F_IP_CSUM;
break;
case 2:
lp->csum_offload_on_tx_path =
XAE_FEATURE_FULL_TX_CSUM;
lp->features |= XAE_FEATURE_FULL_TX_CSUM;
/* Can checksum TCP/UDP over IPv4. */
ndev->features |= NETIF_F_IP_CSUM;
break;
default:
lp->csum_offload_on_tx_path = XAE_NO_CSUM_OFFLOAD;
}
}
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,rxcsum", NULL);
if (p) {
switch (be32_to_cpup(p)) {
case 1:
lp->csum_offload_on_rx_path =
XAE_FEATURE_PARTIAL_RX_CSUM;
lp->features |= XAE_FEATURE_PARTIAL_RX_CSUM;
break;
case 2:
lp->csum_offload_on_rx_path =
XAE_FEATURE_FULL_RX_CSUM;
lp->features |= XAE_FEATURE_FULL_RX_CSUM;
break;
default:
lp->csum_offload_on_rx_path = XAE_NO_CSUM_OFFLOAD;
}
}
/* For supporting jumbo frames, the Axi Ethernet hardware must have
* a larger Rx/Tx Memory. Typically, the size must be more than or
* equal to 16384 bytes, so that we can enable jumbo option and start
* supporting jumbo frames. Here we check for memory allocated for
* Rx/Tx in the hardware from the device-tree and accordingly set
* flags. */
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,rxmem", NULL);
if (p) {
if ((be32_to_cpup(p)) >= 0x4000)
lp->jumbo_support = 1;
}
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,temac-type",
NULL);
if (p)
lp->temac_type = be32_to_cpup(p);
p = (__be32 *) of_get_property(op->dev.of_node, "xlnx,phy-type", NULL);
if (p)
lp->phy_type = be32_to_cpup(p);
/* Find the DMA node, map the DMA registers, and decode the DMA IRQs */
np = of_parse_phandle(op->dev.of_node, "axistream-connected", 0);
if (!np) {
dev_err(&op->dev, "could not find DMA node\n");
goto err_iounmap;
}
lp->dma_regs = of_iomap(np, 0);
if (lp->dma_regs) {
dev_dbg(&op->dev, "MEM base: %p\n", lp->dma_regs);
} else {
dev_err(&op->dev, "unable to map DMA registers\n");
of_node_put(np);
}
lp->rx_irq = irq_of_parse_and_map(np, 1);
lp->tx_irq = irq_of_parse_and_map(np, 0);
of_node_put(np);
if ((lp->rx_irq <= 0) || (lp->tx_irq <= 0)) {
dev_err(&op->dev, "could not determine irqs\n");
ret = -ENOMEM;
goto err_iounmap_2;
}
/* Retrieve the MAC address */
addr = of_get_property(op->dev.of_node, "local-mac-address", &size);
if ((!addr) || (size != 6)) {
dev_err(&op->dev, "could not find MAC address\n");
ret = -ENODEV;
goto err_iounmap_2;
}
axienet_set_mac_address(ndev, (void *) addr);
lp->coalesce_count_rx = XAXIDMA_DFT_RX_THRESHOLD;
lp->coalesce_count_tx = XAXIDMA_DFT_TX_THRESHOLD;
lp->phy_node = of_parse_phandle(op->dev.of_node, "phy-handle", 0);
ret = axienet_mdio_setup(lp, op->dev.of_node);
if (ret)
dev_warn(&op->dev, "error registering MDIO bus\n");
ret = register_netdev(lp->ndev);
if (ret) {
dev_err(lp->dev, "register_netdev() error (%i)\n", ret);
goto err_iounmap_2;
}
return 0;
err_iounmap_2:
if (lp->dma_regs)
iounmap(lp->dma_regs);
err_iounmap:
iounmap(lp->regs);
nodev:
free_netdev(ndev);
ndev = NULL;
return ret;
}
static int axienet_of_remove(struct platform_device *op)
{
struct net_device *ndev = platform_get_drvdata(op);
struct axienet_local *lp = netdev_priv(ndev);
axienet_mdio_teardown(lp);
unregister_netdev(ndev);
if (lp->phy_node)
of_node_put(lp->phy_node);
lp->phy_node = NULL;
iounmap(lp->regs);
if (lp->dma_regs)
iounmap(lp->dma_regs);
free_netdev(ndev);
return 0;
}
static struct platform_driver axienet_of_driver = {
.probe = axienet_of_probe,
.remove = axienet_of_remove,
.driver = {
.owner = THIS_MODULE,
.name = "xilinx_axienet",
.of_match_table = axienet_of_match,
},
};
module_platform_driver(axienet_of_driver);
MODULE_DESCRIPTION("Xilinx Axi Ethernet driver");
MODULE_AUTHOR("Xilinx");
MODULE_LICENSE("GPL");