| /include/ "skeleton.dtsi" |
| |
| #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) |
| |
| / { |
| compatible = "marvell,dove"; |
| model = "Marvell Armada 88AP510 SoC"; |
| interrupt-parent = <&intc>; |
| |
| aliases { |
| gpio0 = &gpio0; |
| gpio1 = &gpio1; |
| gpio2 = &gpio2; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "marvell,pj4a", "marvell,sheeva-v7"; |
| device_type = "cpu"; |
| next-level-cache = <&l2>; |
| reg = <0>; |
| }; |
| }; |
| |
| l2: l2-cache { |
| compatible = "marvell,tauros2-cache"; |
| marvell,tauros2-cache-features = <0>; |
| }; |
| |
| mbus { |
| compatible = "marvell,dove-mbus", "marvell,mbus", "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| controller = <&mbusc>; |
| pcie-mem-aperture = <0xe0000000 0x10000000>; /* 256M MEM space */ |
| pcie-io-aperture = <0xf2000000 0x00200000>; /* 2M I/O space */ |
| |
| ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x0100000 /* MBUS regs 1M */ |
| MBUS_ID(0xf0, 0x02) 0 0xf1800000 0x1000000 /* AXI regs 16M */ |
| MBUS_ID(0x01, 0xfd) 0 0xf8000000 0x8000000 /* BootROM 128M */ |
| MBUS_ID(0x03, 0x01) 0 0xc8000000 0x0100000 /* CESA SRAM 1M */ |
| MBUS_ID(0x0d, 0x00) 0 0xf0000000 0x0100000>; /* PMU SRAM 1M */ |
| |
| pcie: pcie-controller { |
| compatible = "marvell,dove-pcie"; |
| status = "disabled"; |
| device_type = "pci"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| msi-parent = <&intc>; |
| bus-range = <0x00 0xff>; |
| |
| ranges = <0x82000000 0x0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x2000 |
| 0x82000000 0x0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x2000 |
| 0x82000000 0x1 0x0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 Mem */ |
| 0x81000000 0x1 0x0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 I/O */ |
| 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */ |
| 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */ |
| |
| pcie-port@0 { |
| device_type = "pci"; |
| status = "disabled"; |
| assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; |
| reg = <0x0800 0 0 0 0>; |
| clocks = <&gate_clk 4>; |
| marvell,pcie-port = <0>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 |
| 0x81000000 0 0 0x81000000 0x1 0 1 0>; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &intc 16>; |
| }; |
| |
| pcie-port@1 { |
| device_type = "pci"; |
| status = "disabled"; |
| assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; |
| reg = <0x1000 0 0 0 0>; |
| clocks = <&gate_clk 5>; |
| marvell,pcie-port = <1>; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 |
| 0x81000000 0 0 0x81000000 0x2 0 1 0>; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &intc 18>; |
| }; |
| }; |
| |
| internal-regs { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x00000000 MBUS_ID(0xf0, 0x01) 0 0x0100000 /* MBUS regs 1M */ |
| 0x00800000 MBUS_ID(0xf0, 0x02) 0 0x1000000 /* AXI regs 16M */ |
| 0xffffe000 MBUS_ID(0x03, 0x01) 0 0x0000800 /* CESA SRAM 2k */ |
| 0xfffff000 MBUS_ID(0x0d, 0x00) 0 0x0000800>; /* PMU SRAM 2k */ |
| |
| spi0: spi-ctrl@10600 { |
| compatible = "marvell,orion-spi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cell-index = <0>; |
| interrupts = <6>; |
| reg = <0x10600 0x28>; |
| clocks = <&core_clk 0>; |
| pinctrl-0 = <&pmx_spi0>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c-ctrl@11000 { |
| compatible = "marvell,mv64xxx-i2c"; |
| reg = <0x11000 0x20>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <11>; |
| clock-frequency = <400000>; |
| timeout-ms = <1000>; |
| clocks = <&core_clk 0>; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@12000 { |
| compatible = "ns16550a"; |
| reg = <0x12000 0x100>; |
| reg-shift = <2>; |
| interrupts = <7>; |
| clocks = <&core_clk 0>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@12100 { |
| compatible = "ns16550a"; |
| reg = <0x12100 0x100>; |
| reg-shift = <2>; |
| interrupts = <8>; |
| clocks = <&core_clk 0>; |
| pinctrl-0 = <&pmx_uart1>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@12200 { |
| compatible = "ns16550a"; |
| reg = <0x12000 0x100>; |
| reg-shift = <2>; |
| interrupts = <9>; |
| clocks = <&core_clk 0>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@12300 { |
| compatible = "ns16550a"; |
| reg = <0x12100 0x100>; |
| reg-shift = <2>; |
| interrupts = <10>; |
| clocks = <&core_clk 0>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi-ctrl@14600 { |
| compatible = "marvell,orion-spi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cell-index = <1>; |
| interrupts = <5>; |
| reg = <0x14600 0x28>; |
| clocks = <&core_clk 0>; |
| status = "disabled"; |
| }; |
| |
| mbusc: mbus-ctrl@20000 { |
| compatible = "marvell,mbus-controller"; |
| reg = <0x20000 0x80>, <0x800100 0x8>; |
| }; |
| |
| sysc: system-ctrl@20000 { |
| compatible = "marvell,orion-system-controller"; |
| reg = <0x20000 0x110>; |
| }; |
| |
| bridge_intc: bridge-interrupt-ctrl@20110 { |
| compatible = "marvell,orion-bridge-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x20110 0x8>; |
| interrupts = <0>; |
| marvell,#interrupts = <5>; |
| }; |
| |
| intc: main-interrupt-ctrl@20200 { |
| compatible = "marvell,orion-intc"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x20200 0x10>, <0x20210 0x10>; |
| }; |
| |
| timer: timer@20300 { |
| compatible = "marvell,orion-timer"; |
| reg = <0x20300 0x20>; |
| interrupt-parent = <&bridge_intc>; |
| interrupts = <1>, <2>; |
| clocks = <&core_clk 0>; |
| }; |
| |
| watchdog@20300 { |
| compatible = "marvell,orion-wdt"; |
| reg = <0x20300 0x28>, <0x20108 0x4>; |
| interrupt-parent = <&bridge_intc>; |
| interrupts = <3>; |
| clocks = <&core_clk 0>; |
| }; |
| |
| crypto: crypto-engine@30000 { |
| compatible = "marvell,orion-crypto"; |
| reg = <0x30000 0x10000>, |
| <0xffffe000 0x800>; |
| reg-names = "regs", "sram"; |
| interrupts = <31>; |
| clocks = <&gate_clk 15>; |
| status = "okay"; |
| }; |
| |
| ehci0: usb-host@50000 { |
| compatible = "marvell,orion-ehci"; |
| reg = <0x50000 0x1000>; |
| interrupts = <24>; |
| clocks = <&gate_clk 0>; |
| status = "okay"; |
| }; |
| |
| ehci1: usb-host@51000 { |
| compatible = "marvell,orion-ehci"; |
| reg = <0x51000 0x1000>; |
| interrupts = <25>; |
| clocks = <&gate_clk 1>; |
| status = "okay"; |
| }; |
| |
| xor0: dma-engine@60800 { |
| compatible = "marvell,orion-xor"; |
| reg = <0x60800 0x100 |
| 0x60a00 0x100>; |
| clocks = <&gate_clk 23>; |
| status = "okay"; |
| |
| channel0 { |
| interrupts = <39>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| |
| channel1 { |
| interrupts = <40>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| }; |
| |
| xor1: dma-engine@60900 { |
| compatible = "marvell,orion-xor"; |
| reg = <0x60900 0x100 |
| 0x60b00 0x100>; |
| clocks = <&gate_clk 24>; |
| status = "okay"; |
| |
| channel0 { |
| interrupts = <42>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| |
| channel1 { |
| interrupts = <43>; |
| dmacap,memcpy; |
| dmacap,xor; |
| }; |
| }; |
| |
| sdio1: sdio-host@90000 { |
| compatible = "marvell,dove-sdhci"; |
| reg = <0x90000 0x100>; |
| interrupts = <36>, <38>; |
| clocks = <&gate_clk 9>; |
| pinctrl-0 = <&pmx_sdio1>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| eth: ethernet-ctrl@72000 { |
| compatible = "marvell,orion-eth"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x72000 0x4000>; |
| clocks = <&gate_clk 2>; |
| marvell,tx-checksum-limit = <1600>; |
| status = "disabled"; |
| |
| ethernet-port@0 { |
| compatible = "marvell,orion-eth-port"; |
| reg = <0>; |
| interrupts = <29>; |
| /* overwrite MAC address in bootloader */ |
| local-mac-address = [00 00 00 00 00 00]; |
| phy-handle = <ðphy>; |
| }; |
| }; |
| |
| mdio: mdio-bus@72004 { |
| compatible = "marvell,orion-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x72004 0x84>; |
| interrupts = <30>; |
| clocks = <&gate_clk 2>; |
| status = "disabled"; |
| |
| ethphy: ethernet-phy { |
| /* set phy address in board file */ |
| }; |
| }; |
| |
| sdio0: sdio-host@92000 { |
| compatible = "marvell,dove-sdhci"; |
| reg = <0x92000 0x100>; |
| interrupts = <35>, <37>; |
| clocks = <&gate_clk 8>; |
| pinctrl-0 = <&pmx_sdio0>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| sata0: sata-host@a0000 { |
| compatible = "marvell,orion-sata"; |
| reg = <0xa0000 0x2400>; |
| interrupts = <62>; |
| clocks = <&gate_clk 3>; |
| phys = <&sata_phy0>; |
| phy-names = "port0"; |
| nr-ports = <1>; |
| status = "disabled"; |
| }; |
| |
| sata_phy0: sata-phy@a2000 { |
| compatible = "marvell,mvebu-sata-phy"; |
| reg = <0xa2000 0x0334>; |
| clocks = <&gate_clk 3>; |
| clock-names = "sata"; |
| #phy-cells = <0>; |
| status = "ok"; |
| }; |
| |
| audio0: audio-controller@b0000 { |
| compatible = "marvell,dove-audio"; |
| reg = <0xb0000 0x2210>; |
| interrupts = <19>, <20>; |
| clocks = <&gate_clk 12>; |
| clock-names = "internal"; |
| status = "disabled"; |
| }; |
| |
| audio1: audio-controller@b4000 { |
| compatible = "marvell,dove-audio"; |
| reg = <0xb4000 0x2210>; |
| interrupts = <21>, <22>; |
| clocks = <&gate_clk 13>; |
| clock-names = "internal"; |
| status = "disabled"; |
| }; |
| |
| thermal: thermal-diode@d001c { |
| compatible = "marvell,dove-thermal"; |
| reg = <0xd001c 0x0c>, <0xd005c 0x08>; |
| }; |
| |
| gate_clk: clock-gating-ctrl@d0038 { |
| compatible = "marvell,dove-gating-clock"; |
| reg = <0xd0038 0x4>; |
| clocks = <&core_clk 0>; |
| #clock-cells = <1>; |
| }; |
| |
| pinctrl: pin-ctrl@d0200 { |
| compatible = "marvell,dove-pinctrl"; |
| reg = <0xd0200 0x14>, |
| <0xd0440 0x04>; |
| clocks = <&gate_clk 22>; |
| |
| pmx_gpio_0: pmx-gpio-0 { |
| marvell,pins = "mpp0"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_1: pmx-gpio-1 { |
| marvell,pins = "mpp1"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_2: pmx-gpio-2 { |
| marvell,pins = "mpp2"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_3: pmx-gpio-3 { |
| marvell,pins = "mpp3"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_4: pmx-gpio-4 { |
| marvell,pins = "mpp4"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_5: pmx-gpio-5 { |
| marvell,pins = "mpp5"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_6: pmx-gpio-6 { |
| marvell,pins = "mpp6"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_7: pmx-gpio-7 { |
| marvell,pins = "mpp7"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_8: pmx-gpio-8 { |
| marvell,pins = "mpp8"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_9: pmx-gpio-9 { |
| marvell,pins = "mpp9"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_10: pmx-gpio-10 { |
| marvell,pins = "mpp10"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_11: pmx-gpio-11 { |
| marvell,pins = "mpp11"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_12: pmx-gpio-12 { |
| marvell,pins = "mpp12"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_13: pmx-gpio-13 { |
| marvell,pins = "mpp13"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_audio1_extclk: pmx-audio1-extclk { |
| marvell,pins = "mpp13"; |
| marvell,function = "audio1"; |
| }; |
| |
| pmx_gpio_14: pmx-gpio-14 { |
| marvell,pins = "mpp14"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_15: pmx-gpio-15 { |
| marvell,pins = "mpp15"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_16: pmx-gpio-16 { |
| marvell,pins = "mpp16"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_17: pmx-gpio-17 { |
| marvell,pins = "mpp17"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_18: pmx-gpio-18 { |
| marvell,pins = "mpp18"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_19: pmx-gpio-19 { |
| marvell,pins = "mpp19"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_20: pmx-gpio-20 { |
| marvell,pins = "mpp20"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_gpio_21: pmx-gpio-21 { |
| marvell,pins = "mpp21"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_camera: pmx-camera { |
| marvell,pins = "mpp_camera"; |
| marvell,function = "camera"; |
| }; |
| |
| pmx_camera_gpio: pmx-camera-gpio { |
| marvell,pins = "mpp_camera"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_sdio0: pmx-sdio0 { |
| marvell,pins = "mpp_sdio0"; |
| marvell,function = "sdio0"; |
| }; |
| |
| pmx_sdio0_gpio: pmx-sdio0-gpio { |
| marvell,pins = "mpp_sdio0"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_sdio1: pmx-sdio1 { |
| marvell,pins = "mpp_sdio1"; |
| marvell,function = "sdio1"; |
| }; |
| |
| pmx_sdio1_gpio: pmx-sdio1-gpio { |
| marvell,pins = "mpp_sdio1"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_audio1_gpio: pmx-audio1-gpio { |
| marvell,pins = "mpp_audio1"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_audio1_i2s1_spdifo: pmx-audio1-i2s1-spdifo { |
| marvell,pins = "mpp_audio1"; |
| marvell,function = "i2s1/spdifo"; |
| }; |
| |
| pmx_spi0: pmx-spi0 { |
| marvell,pins = "mpp_spi0"; |
| marvell,function = "spi0"; |
| }; |
| |
| pmx_spi0_gpio: pmx-spi0-gpio { |
| marvell,pins = "mpp_spi0"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_uart1: pmx-uart1 { |
| marvell,pins = "mpp_uart1"; |
| marvell,function = "uart1"; |
| }; |
| |
| pmx_uart1_gpio: pmx-uart1-gpio { |
| marvell,pins = "mpp_uart1"; |
| marvell,function = "gpio"; |
| }; |
| |
| pmx_nand: pmx-nand { |
| marvell,pins = "mpp_nand"; |
| marvell,function = "nand"; |
| }; |
| |
| pmx_nand_gpo: pmx-nand-gpo { |
| marvell,pins = "mpp_nand"; |
| marvell,function = "gpo"; |
| }; |
| }; |
| |
| core_clk: core-clocks@d0214 { |
| compatible = "marvell,dove-core-clock"; |
| reg = <0xd0214 0x4>; |
| #clock-cells = <1>; |
| }; |
| |
| gpio0: gpio-ctrl@d0400 { |
| compatible = "marvell,orion-gpio"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0xd0400 0x20>; |
| ngpios = <32>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <12>, <13>, <14>, <60>; |
| }; |
| |
| gpio1: gpio-ctrl@d0420 { |
| compatible = "marvell,orion-gpio"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0xd0420 0x20>; |
| ngpios = <32>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <61>; |
| }; |
| |
| rtc: real-time-clock@d8500 { |
| compatible = "marvell,orion-rtc"; |
| reg = <0xd8500 0x20>; |
| }; |
| |
| gconf: global-config@e802c { |
| compatible = "marvell,dove-global-config", |
| "syscon"; |
| reg = <0xe802c 0x14>; |
| }; |
| |
| gpio2: gpio-ctrl@e8400 { |
| compatible = "marvell,orion-gpio"; |
| #gpio-cells = <2>; |
| gpio-controller; |
| reg = <0xe8400 0x0c>; |
| ngpios = <8>; |
| }; |
| }; |
| }; |
| }; |
