| /* | |
| * atmel platform data | |
| * | |
| * GPL v2 Only | |
| */ | |
| #ifndef __ATMEL_H__ | |
| #define __ATMEL_H__ | |
| #include <linux/mtd/nand.h> | |
| #include <linux/mtd/partitions.h> | |
| #include <linux/device.h> | |
| #include <linux/i2c.h> | |
| #include <linux/leds.h> | |
| #include <linux/spi/spi.h> | |
| #include <linux/usb/atmel_usba_udc.h> | |
| #include <linux/atmel-mci.h> | |
| #include <sound/atmel-ac97c.h> | |
| #include <linux/serial.h> | |
| #include <linux/platform_data/macb.h> | |
| /* | |
| * at91: 6 USARTs and one DBGU port (SAM9260) | |
| * avr32: 4 | |
| */ | |
| #define ATMEL_MAX_UART 7 | |
| /* USB Device */ | |
| struct at91_udc_data { | |
| int vbus_pin; /* high == host powering us */ | |
| u8 vbus_active_low; /* vbus polarity */ | |
| u8 vbus_polled; /* Use polling, not interrupt */ | |
| int pullup_pin; /* active == D+ pulled up */ | |
| u8 pullup_active_low; /* true == pullup_pin is active low */ | |
| }; | |
| /* Compact Flash */ | |
| struct at91_cf_data { | |
| int irq_pin; /* I/O IRQ */ | |
| int det_pin; /* Card detect */ | |
| int vcc_pin; /* power switching */ | |
| int rst_pin; /* card reset */ | |
| u8 chipselect; /* EBI Chip Select number */ | |
| u8 flags; | |
| #define AT91_CF_TRUE_IDE 0x01 | |
| #define AT91_IDE_SWAP_A0_A2 0x02 | |
| }; | |
| /* USB Host */ | |
| #define AT91_MAX_USBH_PORTS 3 | |
| struct at91_usbh_data { | |
| int vbus_pin[AT91_MAX_USBH_PORTS]; /* port power-control pin */ | |
| int overcurrent_pin[AT91_MAX_USBH_PORTS]; | |
| u8 ports; /* number of ports on root hub */ | |
| u8 overcurrent_supported; | |
| u8 vbus_pin_active_low[AT91_MAX_USBH_PORTS]; | |
| u8 overcurrent_status[AT91_MAX_USBH_PORTS]; | |
| u8 overcurrent_changed[AT91_MAX_USBH_PORTS]; | |
| }; | |
| /* NAND / SmartMedia */ | |
| struct atmel_nand_data { | |
| int enable_pin; /* chip enable */ | |
| int det_pin; /* card detect */ | |
| int rdy_pin; /* ready/busy */ | |
| u8 rdy_pin_active_low; /* rdy_pin value is inverted */ | |
| u8 ale; /* address line number connected to ALE */ | |
| u8 cle; /* address line number connected to CLE */ | |
| u8 bus_width_16; /* buswidth is 16 bit */ | |
| u8 ecc_mode; /* ecc mode */ | |
| u8 on_flash_bbt; /* bbt on flash */ | |
| struct mtd_partition *parts; | |
| unsigned int num_parts; | |
| bool has_dma; /* support dma transfer */ | |
| /* default is false, only for at32ap7000 chip is true */ | |
| bool need_reset_workaround; | |
| }; | |
| /* Serial */ | |
| struct atmel_uart_data { | |
| int num; /* port num */ | |
| short use_dma_tx; /* use transmit DMA? */ | |
| short use_dma_rx; /* use receive DMA? */ | |
| void __iomem *regs; /* virt. base address, if any */ | |
| struct serial_rs485 rs485; /* rs485 settings */ | |
| }; | |
| /* CAN */ | |
| struct at91_can_data { | |
| void (*transceiver_switch)(int on); | |
| }; | |
| /* FIXME: this needs a better location, but gets stuff building again */ | |
| extern int at91_suspend_entering_slow_clock(void); | |
| #endif /* __ATMEL_H__ */ |