Documentation/devicetree/bindings/display/msm/dsi.txt - arm/linux - Git at Google

 Qualcomm Technologies Inc. adreno/snapdragon DSI output

 DSI Controller:
 Required properties:
 - compatible:
   * "qcom,mdss-dsi-ctrl"
 - reg: Physical base address and length of the registers of controller
 - reg-names: The names of register regions. The following regions are required:
   * "dsi_ctrl"
 - qcom,dsi-host-index: The ID of DSI controller hardware instance. This should
   be 0 or 1, since we have 2 DSI controllers at most for now.
 - interrupts: The interrupt signal from the DSI block.
 - power-domains: Should be <&mmcc MDSS_GDSC>.
 - clocks: Phandles to device clocks.
 - clock-names: the following clocks are required:
   * "mdp_core_clk"
   * "iface_clk"
   * "bus_clk"
   * "core_mmss_clk"
   * "byte_clk"
   * "pixel_clk"
   * "core_clk"
   For DSIv2, we need an additional clock:
    * "src_clk"
 - assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform.
 - assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
   by a DSI PHY block. See [1] for details on clock bindings.
 - vdd-supply: phandle to vdd regulator device node
 - vddio-supply: phandle to vdd-io regulator device node
 - vdda-supply: phandle to vdda regulator device node
 - phys: phandle to DSI PHY device node
 - phy-names: the name of the corresponding PHY device
 - syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
 - ports: Contains 2 DSI controller ports as child nodes. Each port contains
   an endpoint subnode as defined in [2] and [3].

 Optional properties:
 - panel@0: Node of panel connected to this DSI controller.
   See files in [4] for each supported panel.
 - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
   driving a panel which needs 2 DSI links.
 - qcom,master-dsi: Boolean value indicating if the DSI controller is driving
   the master link of the 2-DSI panel.
 - qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
   driving a 2-DSI panel whose 2 links need receive command simultaneously.
 - interrupt-parent: phandle to the MDP block if the interrupt signal is routed
   through MDP block
 - pinctrl-names: the pin control state names; should contain "default"
 - pinctrl-0: the default pinctrl state (active)
 - pinctrl-n: the "sleep" pinctrl state
 - ports: contains DSI controller input and output ports as children, each
   containing one endpoint subnode.

   DSI Endpoint properties:
   - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
     input endpoint. For port@1, set to the MDP interface output. See [2] for
     device graph info.

   - data-lanes: this describes how the physical DSI data lanes are mapped
     to the logical lanes on the given platform. The value contained in
     index n describes what physical lane is mapped to the logical lane n
     (DATAn, where n lies between 0 and 3). The clock lane position is fixed
     and can't be changed. Hence, they aren't a part of the DT bindings. See
     [3] for more info on the data-lanes property.

     For example:

     data-lanes = <3 0 1 2>;

     The above mapping describes that the logical data lane DATA0 is mapped to
     the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
     to phys DATA1 and logic DATA3 to phys DATA2.

     There are only a limited number of physical to logical mappings possible:
     <0 1 2 3>
     <1 2 3 0>
     <2 3 0 1>
     <3 0 1 2>
     <0 3 2 1>
     <1 0 3 2>
     <2 1 0 3>
     <3 2 1 0>

 DSI PHY:
 Required properties:
 - compatible: Could be the following
   * "qcom,dsi-phy-28nm-hpm"
   * "qcom,dsi-phy-28nm-lp"
   * "qcom,dsi-phy-20nm"
   * "qcom,dsi-phy-28nm-8960"
 - reg: Physical base address and length of the registers of PLL, PHY and PHY
   regulator
 - reg-names: The names of register regions. The following regions are required:
   * "dsi_pll"
   * "dsi_phy"
   * "dsi_phy_regulator"
 - clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
   2 clocks: A byte clock (index 0), and a pixel clock (index 1).
 - qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should
   be 0 or 1, since we have 2 DSI PHYs at most for now.
 - power-domains: Should be <&mmcc MDSS_GDSC>.
 - clocks: Phandles to device clocks. See [1] for details on clock bindings.
 - clock-names: the following clocks are required:
   * "iface_clk"
 - vddio-supply: phandle to vdd-io regulator device node

 Optional properties:
 - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
   regulator is wanted.

 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/graph.txt
 [3] Documentation/devicetree/bindings/media/video-interfaces.txt
 [4] Documentation/devicetree/bindings/display/panel/

 Example:
 	dsi0: dsi@fd922800 {
 		compatible = "qcom,mdss-dsi-ctrl";
 		qcom,dsi-host-index = <0>;
 		interrupt-parent = <&mdp>;
 		interrupts = <4 0>;
 		reg-names = "dsi_ctrl";
 		reg = <0xfd922800 0x200>;
 		power-domains = <&mmcc MDSS_GDSC>;
 		clock-names =
 			"bus_clk",
 			"byte_clk",
 			"core_clk",
 			"core_mmss_clk",
 			"iface_clk",
 			"mdp_core_clk",
 			"pixel_clk";
 		clocks =
 			<&mmcc MDSS_AXI_CLK>,
 			<&mmcc MDSS_BYTE0_CLK>,
 			<&mmcc MDSS_ESC0_CLK>,
 			<&mmcc MMSS_MISC_AHB_CLK>,
 			<&mmcc MDSS_AHB_CLK>,
 			<&mmcc MDSS_MDP_CLK>,
 			<&mmcc MDSS_PCLK0_CLK>;

 		assigned-clocks =
 				 <&mmcc BYTE0_CLK_SRC>,
 				 <&mmcc PCLK0_CLK_SRC>;
 		assigned-clock-parents =
 				 <&dsi_phy0 0>,
 				 <&dsi_phy0 1>;

 		vdda-supply = <&pma8084_l2>;
 		vdd-supply = <&pma8084_l22>;
 		vddio-supply = <&pma8084_l12>;

 		phys = <&dsi_phy0>;
 		phy-names ="dsi-phy";

 		qcom,dual-dsi-mode;
 		qcom,master-dsi;
 		qcom,sync-dual-dsi;

 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&dsi_active>;
 		pinctrl-1 = <&dsi_suspend>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				dsi0_in: endpoint {
 					remote-endpoint = <&mdp_intf1_out>;
 				};
 			};

 			port@1 {
 				reg = <1>;
 				dsi0_out: endpoint {
 					remote-endpoint = <&panel_in>;
 					data-lanes = <0 1 2 3>;
 				};
 			};
 		};

 		panel: panel@0 {
 			compatible = "sharp,lq101r1sx01";
 			reg = <0>;
 			link2 = <&secondary>;

 			power-supply = <...>;
 			backlight = <...>;

 			port {
 				panel_in: endpoint {
 					remote-endpoint = <&dsi0_out>;
 				};
 			};
 		};
 	};

 	dsi_phy0: dsi-phy@fd922a00 {
 		compatible = "qcom,dsi-phy-28nm-hpm";
 		qcom,dsi-phy-index = <0>;
 		reg-names =
 			"dsi_pll",
 			"dsi_phy",
 			"dsi_phy_regulator";
 		reg =   <0xfd922a00 0xd4>,
 			<0xfd922b00 0x2b0>,
 			<0xfd922d80 0x7b>;
 		clock-names = "iface_clk";
 		clocks = <&mmcc MDSS_AHB_CLK>;
 		#clock-cells = <1>;
 		vddio-supply = <&pma8084_l12>;

 		qcom,dsi-phy-regulator-ldo-mode;
 	};
	Qualcomm Technologies Inc. adreno/snapdragon DSI output

	DSI Controller:
	Required properties:
	- compatible:
	* "qcom,mdss-dsi-ctrl"
	- reg: Physical base address and length of the registers of controller
	- reg-names: The names of register regions. The following regions are required:
	* "dsi_ctrl"
	- qcom,dsi-host-index: The ID of DSI controller hardware instance. This should
	be 0 or 1, since we have 2 DSI controllers at most for now.
	- interrupts: The interrupt signal from the DSI block.
	- power-domains: Should be <&mmcc MDSS_GDSC>.
	- clocks: Phandles to device clocks.
	- clock-names: the following clocks are required:
	* "mdp_core_clk"
	* "iface_clk"
	* "bus_clk"
	* "core_mmss_clk"
	* "byte_clk"
	* "pixel_clk"
	* "core_clk"
	For DSIv2, we need an additional clock:
	* "src_clk"
	- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform.
	- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided
	by a DSI PHY block. See [1] for details on clock bindings.
	- vdd-supply: phandle to vdd regulator device node
	- vddio-supply: phandle to vdd-io regulator device node
	- vdda-supply: phandle to vdda regulator device node
	- phys: phandle to DSI PHY device node
	- phy-names: the name of the corresponding PHY device
	- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2)
	- ports: Contains 2 DSI controller ports as child nodes. Each port contains
	an endpoint subnode as defined in [2] and [3].

	Optional properties:
	- panel@0: Node of panel connected to this DSI controller.
	See files in [4] for each supported panel.
	- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is
	driving a panel which needs 2 DSI links.
	- qcom,master-dsi: Boolean value indicating if the DSI controller is driving
	the master link of the 2-DSI panel.
	- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is
	driving a 2-DSI panel whose 2 links need receive command simultaneously.
	- interrupt-parent: phandle to the MDP block if the interrupt signal is routed
	through MDP block
	- pinctrl-names: the pin control state names; should contain "default"
	- pinctrl-0: the default pinctrl state (active)
	- pinctrl-n: the "sleep" pinctrl state
	- ports: contains DSI controller input and output ports as children, each
	containing one endpoint subnode.

	DSI Endpoint properties:
	- remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
	input endpoint. For port@1, set to the MDP interface output. See [2] for
	device graph info.

	- data-lanes: this describes how the physical DSI data lanes are mapped
	to the logical lanes on the given platform. The value contained in
	index n describes what physical lane is mapped to the logical lane n
	(DATAn, where n lies between 0 and 3). The clock lane position is fixed
	and can't be changed. Hence, they aren't a part of the DT bindings. See
	[3] for more info on the data-lanes property.

	For example:

	data-lanes = <3 0 1 2>;

	The above mapping describes that the logical data lane DATA0 is mapped to
	the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2
	to phys DATA1 and logic DATA3 to phys DATA2.

	There are only a limited number of physical to logical mappings possible:
	<0 1 2 3>
	<1 2 3 0>
	<2 3 0 1>
	<3 0 1 2>
	<0 3 2 1>
	<1 0 3 2>
	<2 1 0 3>
	<3 2 1 0>

	DSI PHY:
	Required properties:
	- compatible: Could be the following
	* "qcom,dsi-phy-28nm-hpm"
	* "qcom,dsi-phy-28nm-lp"
	* "qcom,dsi-phy-20nm"
	* "qcom,dsi-phy-28nm-8960"
	- reg: Physical base address and length of the registers of PLL, PHY and PHY
	regulator
	- reg-names: The names of register regions. The following regions are required:
	* "dsi_pll"
	* "dsi_phy"
	* "dsi_phy_regulator"
	- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating
	2 clocks: A byte clock (index 0), and a pixel clock (index 1).
	- qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should
	be 0 or 1, since we have 2 DSI PHYs at most for now.
	- power-domains: Should be <&mmcc MDSS_GDSC>.
	- clocks: Phandles to device clocks. See [1] for details on clock bindings.
	- clock-names: the following clocks are required:
	* "iface_clk"
	- vddio-supply: phandle to vdd-io regulator device node

	Optional properties:
	- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
	regulator is wanted.

	[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
	[2] Documentation/devicetree/bindings/graph.txt
	[3] Documentation/devicetree/bindings/media/video-interfaces.txt
	[4] Documentation/devicetree/bindings/display/panel/

	Example:
	dsi0: dsi@fd922800 {
	compatible = "qcom,mdss-dsi-ctrl";
	qcom,dsi-host-index = <0>;
	interrupt-parent = <&mdp>;
	interrupts = <4 0>;
	reg-names = "dsi_ctrl";
	reg = <0xfd922800 0x200>;
	power-domains = <&mmcc MDSS_GDSC>;
	clock-names =
	"bus_clk",
	"byte_clk",
	"core_clk",
	"core_mmss_clk",
	"iface_clk",
	"mdp_core_clk",
	"pixel_clk";
	clocks =
	<&mmcc MDSS_AXI_CLK>,
	<&mmcc MDSS_BYTE0_CLK>,
	<&mmcc MDSS_ESC0_CLK>,
	<&mmcc MMSS_MISC_AHB_CLK>,
	<&mmcc MDSS_AHB_CLK>,
	<&mmcc MDSS_MDP_CLK>,
	<&mmcc MDSS_PCLK0_CLK>;

	assigned-clocks =
	<&mmcc BYTE0_CLK_SRC>,
	<&mmcc PCLK0_CLK_SRC>;
	assigned-clock-parents =
	<&dsi_phy0 0>,
	<&dsi_phy0 1>;

	vdda-supply = <&pma8084_l2>;
	vdd-supply = <&pma8084_l22>;
	vddio-supply = <&pma8084_l12>;

	phys = <&dsi_phy0>;
	phy-names ="dsi-phy";

	qcom,dual-dsi-mode;
	qcom,master-dsi;
	qcom,sync-dual-dsi;

	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&dsi_active>;
	pinctrl-1 = <&dsi_suspend>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	dsi0_in: endpoint {
	remote-endpoint = <&mdp_intf1_out>;
	};
	};

	port@1 {
	reg = <1>;
	dsi0_out: endpoint {
	remote-endpoint = <&panel_in>;
	data-lanes = <0 1 2 3>;
	};
	};
	};

	panel: panel@0 {
	compatible = "sharp,lq101r1sx01";
	reg = <0>;
	link2 = <&secondary>;

	power-supply = <...>;
	backlight = <...>;

	port {
	panel_in: endpoint {
	remote-endpoint = <&dsi0_out>;
	};
	};
	};
	};

	dsi_phy0: dsi-phy@fd922a00 {
	compatible = "qcom,dsi-phy-28nm-hpm";
	qcom,dsi-phy-index = <0>;
	reg-names =
	"dsi_pll",
	"dsi_phy",
	"dsi_phy_regulator";
	reg = <0xfd922a00 0xd4>,
	<0xfd922b00 0x2b0>,
	<0xfd922d80 0x7b>;
	clock-names = "iface_clk";
	clocks = <&mmcc MDSS_AHB_CLK>;
	#clock-cells = <1>;
	vddio-supply = <&pma8084_l12>;

	qcom,dsi-phy-regulator-ldo-mode;
	};