| /* | |
| * QNAP TS-109/TS-209 Board Setup | |
| * | |
| * Maintainer: Byron Bradley <byron.bbradley@gmail.com> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version | |
| * 2 of the License, or (at your option) any later version. | |
| */ | |
| #include <linux/gpio.h> | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/pci.h> | |
| #include <linux/irq.h> | |
| #include <linux/mtd/physmap.h> | |
| #include <linux/mtd/rawnand.h> | |
| #include <linux/mv643xx_eth.h> | |
| #include <linux/gpio_keys.h> | |
| #include <linux/input.h> | |
| #include <linux/i2c.h> | |
| #include <linux/serial_reg.h> | |
| #include <linux/ata_platform.h> | |
| #include <asm/mach-types.h> | |
| #include <asm/mach/arch.h> | |
| #include <asm/mach/pci.h> | |
| #include "common.h" | |
| #include "mpp.h" | |
| #include "orion5x.h" | |
| #include "tsx09-common.h" | |
| #define QNAP_TS209_NOR_BOOT_BASE 0xf4000000 | |
| #define QNAP_TS209_NOR_BOOT_SIZE SZ_8M | |
| /**************************************************************************** | |
| * 8MiB NOR flash. The struct mtd_partition is not in the same order as the | |
| * partitions on the device because we want to keep compatibility with | |
| * existing QNAP firmware. | |
| * | |
| * Layout as used by QNAP: | |
| * [2] 0x00000000-0x00200000 : "Kernel" | |
| * [3] 0x00200000-0x00600000 : "RootFS1" | |
| * [4] 0x00600000-0x00700000 : "RootFS2" | |
| * [6] 0x00700000-0x00760000 : "NAS Config" (read-only) | |
| * [5] 0x00760000-0x00780000 : "U-Boot Config" | |
| * [1] 0x00780000-0x00800000 : "U-Boot" (read-only) | |
| ***************************************************************************/ | |
| static struct mtd_partition qnap_ts209_partitions[] = { | |
| { | |
| .name = "U-Boot", | |
| .size = 0x00080000, | |
| .offset = 0x00780000, | |
| .mask_flags = MTD_WRITEABLE, | |
| }, { | |
| .name = "Kernel", | |
| .size = 0x00200000, | |
| .offset = 0, | |
| }, { | |
| .name = "RootFS1", | |
| .size = 0x00400000, | |
| .offset = 0x00200000, | |
| }, { | |
| .name = "RootFS2", | |
| .size = 0x00100000, | |
| .offset = 0x00600000, | |
| }, { | |
| .name = "U-Boot Config", | |
| .size = 0x00020000, | |
| .offset = 0x00760000, | |
| }, { | |
| .name = "NAS Config", | |
| .size = 0x00060000, | |
| .offset = 0x00700000, | |
| .mask_flags = MTD_WRITEABLE, | |
| }, | |
| }; | |
| static struct physmap_flash_data qnap_ts209_nor_flash_data = { | |
| .width = 1, | |
| .parts = qnap_ts209_partitions, | |
| .nr_parts = ARRAY_SIZE(qnap_ts209_partitions) | |
| }; | |
| static struct resource qnap_ts209_nor_flash_resource = { | |
| .flags = IORESOURCE_MEM, | |
| .start = QNAP_TS209_NOR_BOOT_BASE, | |
| .end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1, | |
| }; | |
| static struct platform_device qnap_ts209_nor_flash = { | |
| .name = "physmap-flash", | |
| .id = 0, | |
| .dev = { | |
| .platform_data = &qnap_ts209_nor_flash_data, | |
| }, | |
| .resource = &qnap_ts209_nor_flash_resource, | |
| .num_resources = 1, | |
| }; | |
| /***************************************************************************** | |
| * PCI | |
| ****************************************************************************/ | |
| #define QNAP_TS209_PCI_SLOT0_OFFS 7 | |
| #define QNAP_TS209_PCI_SLOT0_IRQ_PIN 6 | |
| #define QNAP_TS209_PCI_SLOT1_IRQ_PIN 7 | |
| static void __init qnap_ts209_pci_preinit(void) | |
| { | |
| int pin; | |
| /* | |
| * Configure PCI GPIO IRQ pins | |
| */ | |
| pin = QNAP_TS209_PCI_SLOT0_IRQ_PIN; | |
| if (gpio_request(pin, "PCI Int1") == 0) { | |
| if (gpio_direction_input(pin) == 0) { | |
| irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW); | |
| } else { | |
| printk(KERN_ERR "qnap_ts209_pci_preinit failed to " | |
| "set_irq_type pin %d\n", pin); | |
| gpio_free(pin); | |
| } | |
| } else { | |
| printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " | |
| "%d\n", pin); | |
| } | |
| pin = QNAP_TS209_PCI_SLOT1_IRQ_PIN; | |
| if (gpio_request(pin, "PCI Int2") == 0) { | |
| if (gpio_direction_input(pin) == 0) { | |
| irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW); | |
| } else { | |
| printk(KERN_ERR "qnap_ts209_pci_preinit failed " | |
| "to set_irq_type pin %d\n", pin); | |
| gpio_free(pin); | |
| } | |
| } else { | |
| printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request " | |
| "%d\n", pin); | |
| } | |
| } | |
| static int __init qnap_ts209_pci_map_irq(const struct pci_dev *dev, u8 slot, | |
| u8 pin) | |
| { | |
| int irq; | |
| /* | |
| * Check for devices with hard-wired IRQs. | |
| */ | |
| irq = orion5x_pci_map_irq(dev, slot, pin); | |
| if (irq != -1) | |
| return irq; | |
| /* | |
| * PCI IRQs are connected via GPIOs. | |
| */ | |
| switch (slot - QNAP_TS209_PCI_SLOT0_OFFS) { | |
| case 0: | |
| return gpio_to_irq(QNAP_TS209_PCI_SLOT0_IRQ_PIN); | |
| case 1: | |
| return gpio_to_irq(QNAP_TS209_PCI_SLOT1_IRQ_PIN); | |
| default: | |
| return -1; | |
| } | |
| } | |
| static struct hw_pci qnap_ts209_pci __initdata = { | |
| .nr_controllers = 2, | |
| .preinit = qnap_ts209_pci_preinit, | |
| .setup = orion5x_pci_sys_setup, | |
| .scan = orion5x_pci_sys_scan_bus, | |
| .map_irq = qnap_ts209_pci_map_irq, | |
| }; | |
| static int __init qnap_ts209_pci_init(void) | |
| { | |
| if (machine_is_ts209()) | |
| pci_common_init(&qnap_ts209_pci); | |
| return 0; | |
| } | |
| subsys_initcall(qnap_ts209_pci_init); | |
| /***************************************************************************** | |
| * RTC S35390A on I2C bus | |
| ****************************************************************************/ | |
| #define TS209_RTC_GPIO 3 | |
| static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = { | |
| I2C_BOARD_INFO("s35390a", 0x30), | |
| .irq = 0, | |
| }; | |
| /**************************************************************************** | |
| * GPIO Attached Keys | |
| * Power button is attached to the PIC microcontroller | |
| ****************************************************************************/ | |
| #define QNAP_TS209_GPIO_KEY_MEDIA 1 | |
| #define QNAP_TS209_GPIO_KEY_RESET 2 | |
| static struct gpio_keys_button qnap_ts209_buttons[] = { | |
| { | |
| .code = KEY_COPY, | |
| .gpio = QNAP_TS209_GPIO_KEY_MEDIA, | |
| .desc = "USB Copy Button", | |
| .active_low = 1, | |
| }, { | |
| .code = KEY_RESTART, | |
| .gpio = QNAP_TS209_GPIO_KEY_RESET, | |
| .desc = "Reset Button", | |
| .active_low = 1, | |
| }, | |
| }; | |
| static struct gpio_keys_platform_data qnap_ts209_button_data = { | |
| .buttons = qnap_ts209_buttons, | |
| .nbuttons = ARRAY_SIZE(qnap_ts209_buttons), | |
| }; | |
| static struct platform_device qnap_ts209_button_device = { | |
| .name = "gpio-keys", | |
| .id = -1, | |
| .num_resources = 0, | |
| .dev = { | |
| .platform_data = &qnap_ts209_button_data, | |
| }, | |
| }; | |
| /***************************************************************************** | |
| * SATA | |
| ****************************************************************************/ | |
| static struct mv_sata_platform_data qnap_ts209_sata_data = { | |
| .n_ports = 2, | |
| }; | |
| /***************************************************************************** | |
| * General Setup | |
| ****************************************************************************/ | |
| static unsigned int ts209_mpp_modes[] __initdata = { | |
| MPP0_UNUSED, | |
| MPP1_GPIO, /* USB copy button */ | |
| MPP2_GPIO, /* Load defaults button */ | |
| MPP3_GPIO, /* GPIO RTC */ | |
| MPP4_UNUSED, | |
| MPP5_UNUSED, | |
| MPP6_GPIO, /* PCI Int A */ | |
| MPP7_GPIO, /* PCI Int B */ | |
| MPP8_UNUSED, | |
| MPP9_UNUSED, | |
| MPP10_UNUSED, | |
| MPP11_UNUSED, | |
| MPP12_SATA_LED, /* SATA 0 presence */ | |
| MPP13_SATA_LED, /* SATA 1 presence */ | |
| MPP14_SATA_LED, /* SATA 0 active */ | |
| MPP15_SATA_LED, /* SATA 1 active */ | |
| MPP16_UART, /* UART1 RXD */ | |
| MPP17_UART, /* UART1 TXD */ | |
| MPP18_GPIO, /* SW_RST */ | |
| MPP19_UNUSED, | |
| 0, | |
| }; | |
| static void __init qnap_ts209_init(void) | |
| { | |
| /* | |
| * Setup basic Orion functions. Need to be called early. | |
| */ | |
| orion5x_init(); | |
| orion5x_mpp_conf(ts209_mpp_modes); | |
| /* | |
| * MPP[20] PCI clock 0 | |
| * MPP[21] PCI clock 1 | |
| * MPP[22] USB 0 over current | |
| * MPP[23-25] Reserved | |
| */ | |
| /* | |
| * Configure peripherals. | |
| */ | |
| mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, | |
| ORION_MBUS_DEVBUS_BOOT_ATTR, | |
| QNAP_TS209_NOR_BOOT_BASE, | |
| QNAP_TS209_NOR_BOOT_SIZE); | |
| platform_device_register(&qnap_ts209_nor_flash); | |
| orion5x_ehci0_init(); | |
| orion5x_ehci1_init(); | |
| qnap_tsx09_find_mac_addr(QNAP_TS209_NOR_BOOT_BASE + | |
| qnap_ts209_partitions[5].offset, | |
| qnap_ts209_partitions[5].size); | |
| orion5x_eth_init(&qnap_tsx09_eth_data); | |
| orion5x_i2c_init(); | |
| orion5x_sata_init(&qnap_ts209_sata_data); | |
| orion5x_uart0_init(); | |
| orion5x_uart1_init(); | |
| orion5x_xor_init(); | |
| platform_device_register(&qnap_ts209_button_device); | |
| /* Get RTC IRQ and register the chip */ | |
| if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) { | |
| if (gpio_direction_input(TS209_RTC_GPIO) == 0) | |
| qnap_ts209_i2c_rtc.irq = gpio_to_irq(TS209_RTC_GPIO); | |
| else | |
| gpio_free(TS209_RTC_GPIO); | |
| } | |
| if (qnap_ts209_i2c_rtc.irq == 0) | |
| pr_warn("qnap_ts209_init: failed to get RTC IRQ\n"); | |
| i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1); | |
| /* register tsx09 specific power-off method */ | |
| pm_power_off = qnap_tsx09_power_off; | |
| } | |
| MACHINE_START(TS209, "QNAP TS-109/TS-209") | |
| /* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */ | |
| .atag_offset = 0x100, | |
| .nr_irqs = ORION5X_NR_IRQS, | |
| .init_machine = qnap_ts209_init, | |
| .map_io = orion5x_map_io, | |
| .init_early = orion5x_init_early, | |
| .init_irq = orion5x_init_irq, | |
| .init_time = orion5x_timer_init, | |
| .fixup = tag_fixup_mem32, | |
| .restart = orion5x_restart, | |
| MACHINE_END |