| This document describes the cx2341x memory map and documents some of the register | |
| space. | |
| Warning! This information was figured out from searching through the memory and | |
| registers, this information may not be correct and is certainly not complete, and | |
| was not derived from anything more than searching through the memory space with | |
| commands like: | |
| ivtvctl -O min=0x02000000,max=0x020000ff | |
| So take this as is, I'm always searching for more stuff, it's a large | |
| register space :-). | |
| Memory Map | |
| ========== | |
| The cx2341x exposes its entire 64M memory space to the PCI host via the PCI BAR0 | |
| (Base Address Register 0). The addresses here are offsets relative to the | |
| address held in BAR0. | |
| 0x00000000-0x00ffffff Encoder memory space | |
| 0x00000000-0x0003ffff Encode.rom | |
| ???-??? MPEG buffer(s) | |
| ???-??? Raw video capture buffer(s) | |
| ???-??? Raw audio capture buffer(s) | |
| ???-??? Display buffers (6 or 9) | |
| 0x01000000-0x01ffffff Decoder memory space | |
| 0x01000000-0x0103ffff Decode.rom | |
| ???-??? MPEG buffers(s) | |
| 0x0114b000-0x0115afff Audio.rom (deprecated?) | |
| 0x02000000-0x0200ffff Register Space | |
| Registers | |
| ========= | |
| The registers occupy the 64k space starting at the 0x02000000 offset from BAR0. | |
| All of these registers are 32 bits wide. | |
| DMA Registers 0x000-0xff: | |
| 0x00 - Control: | |
| 0=reset/cancel, 1=read, 2=write, 4=stop | |
| 0x04 - DMA status: | |
| 1=read busy, 2=write busy, 4=read error, 8=write error, 16=link list error | |
| 0x08 - pci DMA pointer for read link list | |
| 0x0c - pci DMA pointer for write link list | |
| 0x10 - read/write DMA enable: | |
| 1=read enable, 2=write enable | |
| 0x14 - always 0xffffffff, if set any lower instability occurs, 0x00 crashes | |
| 0x18 - ?? | |
| 0x1c - always 0x20 or 32, smaller values slow down DMA transactions | |
| 0x20 - always value of 0x780a010a | |
| 0x24-0x3c - usually just random values??? | |
| 0x40 - Interrupt status | |
| 0x44 - Write a bit here and shows up in Interrupt status 0x40 | |
| 0x48 - Interrupt Mask | |
| 0x4C - always value of 0xfffdffff, | |
| if changed to 0xffffffff DMA write interrupts break. | |
| 0x50 - always 0xffffffff | |
| 0x54 - always 0xffffffff (0x4c, 0x50, 0x54 seem like interrupt masks, are | |
| 3 processors on chip, Java ones, VPU, SPU, APU, maybe these are the | |
| interrupt masks???). | |
| 0x60-0x7C - random values | |
| 0x80 - first write linked list reg, for Encoder Memory addr | |
| 0x84 - first write linked list reg, for pci memory addr | |
| 0x88 - first write linked list reg, for length of buffer in memory addr | |
| (|0x80000000 or this for last link) | |
| 0x8c-0xcc - rest of write linked list reg, 8 sets of 3 total, DMA goes here | |
| from linked list addr in reg 0x0c, firmware must push through or | |
| something. | |
| 0xe0 - first (and only) read linked list reg, for pci memory addr | |
| 0xe4 - first (and only) read linked list reg, for Decoder memory addr | |
| 0xe8 - first (and only) read linked list reg, for length of buffer | |
| 0xec-0xff - Nothing seems to be in these registers, 0xec-f4 are 0x00000000. | |
| Memory locations for Encoder Buffers 0x700-0x7ff: | |
| These registers show offsets of memory locations pertaining to each | |
| buffer area used for encoding, have to shift them by <<1 first. | |
| 0x07F8: Encoder SDRAM refresh | |
| 0x07FC: Encoder SDRAM pre-charge | |
| Memory locations for Decoder Buffers 0x800-0x8ff: | |
| These registers show offsets of memory locations pertaining to each | |
| buffer area used for decoding, have to shift them by <<1 first. | |
| 0x08F8: Decoder SDRAM refresh | |
| 0x08FC: Decoder SDRAM pre-charge | |
| Other memory locations: | |
| 0x2800: Video Display Module control | |
| 0x2D00: AO (audio output?) control | |
| 0x2D24: Bytes Flushed | |
| 0x7000: LSB I2C write clock bit (inverted) | |
| 0x7004: LSB I2C write data bit (inverted) | |
| 0x7008: LSB I2C read clock bit | |
| 0x700c: LSB I2C read data bit | |
| 0x9008: GPIO get input state | |
| 0x900c: GPIO set output state | |
| 0x9020: GPIO direction (Bit7 (GPIO 0..7) - 0:input, 1:output) | |
| 0x9050: SPU control | |
| 0x9054: Reset HW blocks | |
| 0x9058: VPU control | |
| 0xA018: Bit6: interrupt pending? | |
| 0xA064: APU command | |
| Interrupt Status Register | |
| ========================= | |
| The definition of the bits in the interrupt status register 0x0040, and the | |
| interrupt mask 0x0048. If a bit is cleared in the mask, then we want our ISR to | |
| execute. | |
| Bit | |
| 31 Encoder Start Capture | |
| 30 Encoder EOS | |
| 29 Encoder VBI capture | |
| 28 Encoder Video Input Module reset event | |
| 27 Encoder DMA complete | |
| 26 | |
| 25 Decoder copy protect detection event | |
| 24 Decoder audio mode change detection event | |
| 23 | |
| 22 Decoder data request | |
| 21 Decoder I-Frame? done | |
| 20 Decoder DMA complete | |
| 19 Decoder VBI re-insertion | |
| 18 Decoder DMA err (linked-list bad) | |
| Missing | |
| Encoder API call completed | |
| Decoder API call completed | |
| Encoder API post(?) | |
| Decoder API post(?) | |
| Decoder VTRACE event |