| AMD64 specific boot options | |
| There are many others (usually documented in driver documentation), but | |
| only the AMD64 specific ones are listed here. | |
| Machine check | |
| mce=off disable machine check | |
| mce=bootlog Enable logging of machine checks left over from booting. | |
| Disabled by default on AMD because some BIOS leave bogus ones. | |
| If your BIOS doesn't do that it's a good idea to enable though | |
| to make sure you log even machine check events that result | |
| in a reboot. On Intel systems it is enabled by default. | |
| mce=nobootlog | |
| Disable boot machine check logging. | |
| mce=tolerancelevel (number) | |
| 0: always panic, 1: panic if deadlock possible, | |
| 2: try to avoid panic, 3: never panic or exit (for testing) | |
| default is 1 | |
| Can be also set using sysfs which is preferable. | |
| nomce (for compatibility with i386): same as mce=off | |
| Everything else is in sysfs now. | |
| APICs | |
| apic Use IO-APIC. Default | |
| noapic Don't use the IO-APIC. | |
| disableapic Don't use the local APIC | |
| nolapic Don't use the local APIC (alias for i386 compatibility) | |
| pirq=... See Documentation/i386/IO-APIC.txt | |
| noapictimer Don't set up the APIC timer | |
| no_timer_check Don't check the IO-APIC timer. This can work around | |
| problems with incorrect timer initialization on some boards. | |
| apicmaintimer Run time keeping from the local APIC timer instead | |
| of using the PIT/HPET interrupt for this. This is useful | |
| when the PIT/HPET interrupts are unreliable. | |
| noapicmaintimer Don't do time keeping using the APIC timer. | |
| Useful when this option was auto selected, but doesn't work. | |
| apicpmtimer | |
| Do APIC timer calibration using the pmtimer. Implies | |
| apicmaintimer. Useful when your PIT timer is totally | |
| broken. | |
| disable_8254_timer / enable_8254_timer | |
| Enable interrupt 0 timer routing over the 8254 in addition to over | |
| the IO-APIC. The kernel tries to set a sensible default. | |
| Early Console | |
| syntax: earlyprintk=vga | |
| earlyprintk=serial[,ttySn[,baudrate]] | |
| The early console is useful when the kernel crashes before the | |
| normal console is initialized. It is not enabled by | |
| default because it has some cosmetic problems. | |
| Append ,keep to not disable it when the real console takes over. | |
| Only vga or serial at a time, not both. | |
| Currently only ttyS0 and ttyS1 are supported. | |
| Interaction with the standard serial driver is not very good. | |
| The VGA output is eventually overwritten by the real console. | |
| Timing | |
| notsc | |
| Don't use the CPU time stamp counter to read the wall time. | |
| This can be used to work around timing problems on multiprocessor systems | |
| with not properly synchronized CPUs. | |
| report_lost_ticks | |
| Report when timer interrupts are lost because some code turned off | |
| interrupts for too long. | |
| nmi_watchdog=NUMBER[,panic] | |
| NUMBER can be: | |
| 0 don't use an NMI watchdog | |
| 1 use the IO-APIC timer for the NMI watchdog | |
| 2 use the local APIC for the NMI watchdog using a performance counter. Note | |
| This will use one performance counter and the local APIC's performance | |
| vector. | |
| When panic is specified panic when an NMI watchdog timeout occurs. | |
| This is useful when you use a panic=... timeout and need the box | |
| quickly up again. | |
| nohpet | |
| Don't use the HPET timer. | |
| Idle loop | |
| idle=poll | |
| Don't do power saving in the idle loop using HLT, but poll for rescheduling | |
| event. This will make the CPUs eat a lot more power, but may be useful | |
| to get slightly better performance in multiprocessor benchmarks. It also | |
| makes some profiling using performance counters more accurate. | |
| Please note that on systems with MONITOR/MWAIT support (like Intel EM64T | |
| CPUs) this option has no performance advantage over the normal idle loop. | |
| It may also interact badly with hyperthreading. | |
| Rebooting | |
| reboot=b[ios] | t[riple] | k[bd] [, [w]arm | [c]old] | |
| bios Use the CPU reboot vector for warm reset | |
| warm Don't set the cold reboot flag | |
| cold Set the cold reboot flag | |
| triple Force a triple fault (init) | |
| kbd Use the keyboard controller. cold reset (default) | |
| Using warm reset will be much faster especially on big memory | |
| systems because the BIOS will not go through the memory check. | |
| Disadvantage is that not all hardware will be completely reinitialized | |
| on reboot so there may be boot problems on some systems. | |
| reboot=force | |
| Don't stop other CPUs on reboot. This can make reboot more reliable | |
| in some cases. | |
| Non Executable Mappings | |
| noexec=on|off | |
| on Enable(default) | |
| off Disable | |
| SMP | |
| nosmp Only use a single CPU | |
| maxcpus=NUMBER only use upto NUMBER CPUs | |
| cpumask=MASK only use cpus with bits set in mask | |
| additional_cpus=NUM Allow NUM more CPUs for hotplug | |
| (defaults are specified by the BIOS, see Documentation/x86_64/cpu-hotplug-spec) | |
| NUMA | |
| numa=off Only set up a single NUMA node spanning all memory. | |
| numa=noacpi Don't parse the SRAT table for NUMA setup | |
| numa=fake=X Fake X nodes and ignore NUMA setup of the actual machine. | |
| numa=hotadd=percent | |
| Only allow hotadd memory to preallocate page structures upto | |
| percent of already available memory. | |
| numa=hotadd=0 will disable hotadd memory. | |
| ACPI | |
| acpi=off Don't enable ACPI | |
| acpi=ht Use ACPI boot table parsing, but don't enable ACPI | |
| interpreter | |
| acpi=force Force ACPI on (currently not needed) | |
| acpi=strict Disable out of spec ACPI workarounds. | |
| acpi_sci={edge,level,high,low} Set up ACPI SCI interrupt. | |
| acpi=noirq Don't route interrupts | |
| PCI | |
| pci=off Don't use PCI | |
| pci=conf1 Use conf1 access. | |
| pci=conf2 Use conf2 access. | |
| pci=rom Assign ROMs. | |
| pci=assign-busses Assign busses | |
| pci=irqmask=MASK Set PCI interrupt mask to MASK | |
| pci=lastbus=NUMBER Scan upto NUMBER busses, no matter what the mptable says. | |
| pci=noacpi Don't use ACPI to set up PCI interrupt routing. | |
| IOMMU | |
| iommu=[size][,noagp][,off][,force][,noforce][,leak][,memaper[=order]][,merge] | |
| [,forcesac][,fullflush][,nomerge][,noaperture] | |
| size set size of iommu (in bytes) | |
| noagp don't initialize the AGP driver and use full aperture. | |
| off don't use the IOMMU | |
| leak turn on simple iommu leak tracing (only when CONFIG_IOMMU_LEAK is on) | |
| memaper[=order] allocate an own aperture over RAM with size 32MB^order. | |
| noforce don't force IOMMU usage. Default. | |
| force Force IOMMU. | |
| merge Do SG merging. Implies force (experimental) | |
| nomerge Don't do SG merging. | |
| forcesac For SAC mode for masks <40bits (experimental) | |
| fullflush Flush IOMMU on each allocation (default) | |
| nofullflush Don't use IOMMU fullflush | |
| allowed overwrite iommu off workarounds for specific chipsets. | |
| soft Use software bounce buffering (default for Intel machines) | |
| noaperture Don't touch the aperture for AGP. | |
| allowdac Allow DMA >4GB | |
| When off all DMA over >4GB is forced through an IOMMU or bounce | |
| buffering. | |
| nodac Forbid DMA >4GB | |
| panic Always panic when IOMMU overflows | |
| swiotlb=pages[,force] | |
| pages Prereserve that many 128K pages for the software IO bounce buffering. | |
| force Force all IO through the software TLB. | |
| calgary=[64k,128k,256k,512k,1M,2M,4M,8M] | |
| calgary=[translate_empty_slots] | |
| calgary=[disable=<PCI bus number>] | |
| 64k,...,8M - Set the size of each PCI slot's translation table | |
| when using the Calgary IOMMU. This is the size of the translation | |
| table itself in main memory. The smallest table, 64k, covers an IO | |
| space of 32MB; the largest, 8MB table, can cover an IO space of | |
| 4GB. Normally the kernel will make the right choice by itself. | |
| translate_empty_slots - Enable translation even on slots that have | |
| no devices attached to them, in case a device will be hotplugged | |
| in the future. | |
| disable=<PCI bus number> - Disable translation on a given PHB. For | |
| example, the built-in graphics adapter resides on the first bridge | |
| (PCI bus number 0); if translation (isolation) is enabled on this | |
| bridge, X servers that access the hardware directly from user | |
| space might stop working. Use this option if you have devices that | |
| are accessed from userspace directly on some PCI host bridge. | |
| Debugging | |
| oops=panic Always panic on oopses. Default is to just kill the process, | |
| but there is a small probability of deadlocking the machine. | |
| This will also cause panics on machine check exceptions. | |
| Useful together with panic=30 to trigger a reboot. | |
| kstack=N Print that many words from the kernel stack in oops dumps. | |
| pagefaulttrace Dump all page faults. Only useful for extreme debugging | |
| and will create a lot of output. | |
| call_trace=[old|both|newfallback|new] | |
| old: use old inexact backtracer | |
| new: use new exact dwarf2 unwinder | |
| both: print entries from both | |
| newfallback: use new unwinder but fall back to old if it gets | |
| stuck (default) | |
| call_trace=[old|both|newfallback|new] | |
| old: use old inexact backtracer | |
| new: use new exact dwarf2 unwinder | |
| both: print entries from both | |
| newfallback: use new unwinder but fall back to old if it gets | |
| stuck (default) | |
| Misc | |
| noreplacement Don't replace instructions with more appropriate ones | |
| for the CPU. This may be useful on asymmetric MP systems | |
| where some CPU have less capabilities than the others. |