| /* $Id: traps.c,v 1.4 2005/04/24 18:47:55 starvik Exp $ | |
| * | |
| * linux/arch/cris/arch-v10/traps.c | |
| * | |
| * Heler functions for trap handlers | |
| * | |
| * Copyright (C) 2000-2002 Axis Communications AB | |
| * | |
| * Authors: Bjorn Wesen | |
| * Hans-Peter Nilsson | |
| * | |
| */ | |
| #include <linux/ptrace.h> | |
| #include <asm/uaccess.h> | |
| #include <asm/arch/sv_addr_ag.h> | |
| extern int raw_printk(const char *fmt, ...); | |
| void | |
| show_registers(struct pt_regs * regs) | |
| { | |
| /* We either use rdusp() - the USP register, which might not | |
| correspond to the current process for all cases we're called, | |
| or we use the current->thread.usp, which is not up to date for | |
| the current process. Experience shows we want the USP | |
| register. */ | |
| unsigned long usp = rdusp(); | |
| raw_printk("IRP: %08lx SRP: %08lx DCCR: %08lx USP: %08lx MOF: %08lx\n", | |
| regs->irp, regs->srp, regs->dccr, usp, regs->mof ); | |
| raw_printk(" r0: %08lx r1: %08lx r2: %08lx r3: %08lx\n", | |
| regs->r0, regs->r1, regs->r2, regs->r3); | |
| raw_printk(" r4: %08lx r5: %08lx r6: %08lx r7: %08lx\n", | |
| regs->r4, regs->r5, regs->r6, regs->r7); | |
| raw_printk(" r8: %08lx r9: %08lx r10: %08lx r11: %08lx\n", | |
| regs->r8, regs->r9, regs->r10, regs->r11); | |
| raw_printk("r12: %08lx r13: %08lx oR10: %08lx sp: %08lx\n", | |
| regs->r12, regs->r13, regs->orig_r10, regs); | |
| raw_printk("R_MMU_CAUSE: %08lx\n", (unsigned long)*R_MMU_CAUSE); | |
| raw_printk("Process %s (pid: %d, stackpage=%08lx)\n", | |
| current->comm, current->pid, (unsigned long)current); | |
| /* | |
| * When in-kernel, we also print out the stack and code at the | |
| * time of the fault.. | |
| */ | |
| if (! user_mode(regs)) { | |
| int i; | |
| show_stack(NULL, (unsigned long*)usp); | |
| /* Dump kernel stack if the previous dump wasn't one. */ | |
| if (usp != 0) | |
| show_stack (NULL, NULL); | |
| raw_printk("\nCode: "); | |
| if(regs->irp < PAGE_OFFSET) | |
| goto bad; | |
| /* Often enough the value at regs->irp does not point to | |
| the interesting instruction, which is most often the | |
| _previous_ instruction. So we dump at an offset large | |
| enough that instruction decoding should be in sync at | |
| the interesting point, but small enough to fit on a row | |
| (sort of). We point out the regs->irp location in a | |
| ksymoops-friendly way by wrapping the byte for that | |
| address in parentheses. */ | |
| for(i = -12; i < 12; i++) | |
| { | |
| unsigned char c; | |
| if(__get_user(c, &((unsigned char*)regs->irp)[i])) { | |
| bad: | |
| raw_printk(" Bad IP value."); | |
| break; | |
| } | |
| if (i == 0) | |
| raw_printk("(%02x) ", c); | |
| else | |
| raw_printk("%02x ", c); | |
| } | |
| raw_printk("\n"); | |
| } | |
| } | |
| /* Called from entry.S when the watchdog has bitten | |
| * We print out something resembling an oops dump, and if | |
| * we have the nice doggy development flag set, we halt here | |
| * instead of rebooting. | |
| */ | |
| extern void reset_watchdog(void); | |
| extern void stop_watchdog(void); | |
| void | |
| watchdog_bite_hook(struct pt_regs *regs) | |
| { | |
| #ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY | |
| local_irq_disable(); | |
| stop_watchdog(); | |
| show_registers(regs); | |
| while(1) /* nothing */; | |
| #else | |
| show_registers(regs); | |
| #endif | |
| } | |
| /* This is normally the 'Oops' routine */ | |
| void | |
| die_if_kernel(const char * str, struct pt_regs * regs, long err) | |
| { | |
| if(user_mode(regs)) | |
| return; | |
| #ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY | |
| /* This printout might take too long and trigger the | |
| * watchdog normally. If we're in the nice doggy | |
| * development mode, stop the watchdog during printout. | |
| */ | |
| stop_watchdog(); | |
| #endif | |
| raw_printk("%s: %04lx\n", str, err & 0xffff); | |
| show_registers(regs); | |
| #ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY | |
| reset_watchdog(); | |
| #endif | |
| do_exit(SIGSEGV); | |
| } | |
| void arch_enable_nmi(void) | |
| { | |
| asm volatile("setf m"); | |
| } |