| /* | |
| * SMP support for power macintosh. | |
| * | |
| * We support both the old "powersurge" SMP architecture | |
| * and the current Core99 (G4 PowerMac) machines. | |
| * | |
| * Note that we don't support the very first rev. of | |
| * Apple/DayStar 2 CPUs board, the one with the funky | |
| * watchdog. Hopefully, none of these should be there except | |
| * maybe internally to Apple. I should probably still add some | |
| * code to detect this card though and disable SMP. --BenH. | |
| * | |
| * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net) | |
| * and Ben Herrenschmidt <benh@kernel.crashing.org>. | |
| * | |
| * Support for DayStar quad CPU cards | |
| * Copyright (C) XLR8, Inc. 1994-2000 | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version | |
| * 2 of the License, or (at your option) any later version. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/sched.h> | |
| #include <linux/smp.h> | |
| #include <linux/smp_lock.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/kernel_stat.h> | |
| #include <linux/delay.h> | |
| #include <linux/init.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/errno.h> | |
| #include <linux/hardirq.h> | |
| #include <linux/cpu.h> | |
| #include <linux/compiler.h> | |
| #include <asm/ptrace.h> | |
| #include <asm/atomic.h> | |
| #include <asm/irq.h> | |
| #include <asm/page.h> | |
| #include <asm/pgtable.h> | |
| #include <asm/sections.h> | |
| #include <asm/io.h> | |
| #include <asm/prom.h> | |
| #include <asm/smp.h> | |
| #include <asm/machdep.h> | |
| #include <asm/pmac_feature.h> | |
| #include <asm/time.h> | |
| #include <asm/mpic.h> | |
| #include <asm/cacheflush.h> | |
| #include <asm/keylargo.h> | |
| #include <asm/pmac_low_i2c.h> | |
| #include <asm/pmac_pfunc.h> | |
| #define DEBUG | |
| #ifdef DEBUG | |
| #define DBG(fmt...) udbg_printf(fmt) | |
| #else | |
| #define DBG(fmt...) | |
| #endif | |
| extern void __secondary_start_pmac_0(void); | |
| extern int pmac_pfunc_base_install(void); | |
| #ifdef CONFIG_PPC32 | |
| /* Sync flag for HW tb sync */ | |
| static volatile int sec_tb_reset = 0; | |
| /* | |
| * Powersurge (old powermac SMP) support. | |
| */ | |
| /* Addresses for powersurge registers */ | |
| #define HAMMERHEAD_BASE 0xf8000000 | |
| #define HHEAD_CONFIG 0x90 | |
| #define HHEAD_SEC_INTR 0xc0 | |
| /* register for interrupting the primary processor on the powersurge */ | |
| /* N.B. this is actually the ethernet ROM! */ | |
| #define PSURGE_PRI_INTR 0xf3019000 | |
| /* register for storing the start address for the secondary processor */ | |
| /* N.B. this is the PCI config space address register for the 1st bridge */ | |
| #define PSURGE_START 0xf2800000 | |
| /* Daystar/XLR8 4-CPU card */ | |
| #define PSURGE_QUAD_REG_ADDR 0xf8800000 | |
| #define PSURGE_QUAD_IRQ_SET 0 | |
| #define PSURGE_QUAD_IRQ_CLR 1 | |
| #define PSURGE_QUAD_IRQ_PRIMARY 2 | |
| #define PSURGE_QUAD_CKSTOP_CTL 3 | |
| #define PSURGE_QUAD_PRIMARY_ARB 4 | |
| #define PSURGE_QUAD_BOARD_ID 6 | |
| #define PSURGE_QUAD_WHICH_CPU 7 | |
| #define PSURGE_QUAD_CKSTOP_RDBK 8 | |
| #define PSURGE_QUAD_RESET_CTL 11 | |
| #define PSURGE_QUAD_OUT(r, v) (out_8(quad_base + ((r) << 4) + 4, (v))) | |
| #define PSURGE_QUAD_IN(r) (in_8(quad_base + ((r) << 4) + 4) & 0x0f) | |
| #define PSURGE_QUAD_BIS(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v))) | |
| #define PSURGE_QUAD_BIC(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v))) | |
| /* virtual addresses for the above */ | |
| static volatile u8 __iomem *hhead_base; | |
| static volatile u8 __iomem *quad_base; | |
| static volatile u32 __iomem *psurge_pri_intr; | |
| static volatile u8 __iomem *psurge_sec_intr; | |
| static volatile u32 __iomem *psurge_start; | |
| /* values for psurge_type */ | |
| #define PSURGE_NONE -1 | |
| #define PSURGE_DUAL 0 | |
| #define PSURGE_QUAD_OKEE 1 | |
| #define PSURGE_QUAD_COTTON 2 | |
| #define PSURGE_QUAD_ICEGRASS 3 | |
| /* what sort of powersurge board we have */ | |
| static int psurge_type = PSURGE_NONE; | |
| /* | |
| * Set and clear IPIs for powersurge. | |
| */ | |
| static inline void psurge_set_ipi(int cpu) | |
| { | |
| if (psurge_type == PSURGE_NONE) | |
| return; | |
| if (cpu == 0) | |
| in_be32(psurge_pri_intr); | |
| else if (psurge_type == PSURGE_DUAL) | |
| out_8(psurge_sec_intr, 0); | |
| else | |
| PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu); | |
| } | |
| static inline void psurge_clr_ipi(int cpu) | |
| { | |
| if (cpu > 0) { | |
| switch(psurge_type) { | |
| case PSURGE_DUAL: | |
| out_8(psurge_sec_intr, ~0); | |
| case PSURGE_NONE: | |
| break; | |
| default: | |
| PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu); | |
| } | |
| } | |
| } | |
| /* | |
| * On powersurge (old SMP powermac architecture) we don't have | |
| * separate IPIs for separate messages like openpic does. Instead | |
| * we have a bitmap for each processor, where a 1 bit means that | |
| * the corresponding message is pending for that processor. | |
| * Ideally each cpu's entry would be in a different cache line. | |
| * -- paulus. | |
| */ | |
| static unsigned long psurge_smp_message[NR_CPUS]; | |
| void psurge_smp_message_recv(void) | |
| { | |
| int cpu = smp_processor_id(); | |
| int msg; | |
| /* clear interrupt */ | |
| psurge_clr_ipi(cpu); | |
| if (num_online_cpus() < 2) | |
| return; | |
| /* make sure there is a message there */ | |
| for (msg = 0; msg < 4; msg++) | |
| if (test_and_clear_bit(msg, &psurge_smp_message[cpu])) | |
| smp_message_recv(msg); | |
| } | |
| irqreturn_t psurge_primary_intr(int irq, void *d) | |
| { | |
| psurge_smp_message_recv(); | |
| return IRQ_HANDLED; | |
| } | |
| static void smp_psurge_message_pass(int target, int msg) | |
| { | |
| int i; | |
| if (num_online_cpus() < 2) | |
| return; | |
| for_each_online_cpu(i) { | |
| if (target == MSG_ALL | |
| || (target == MSG_ALL_BUT_SELF && i != smp_processor_id()) | |
| || target == i) { | |
| set_bit(msg, &psurge_smp_message[i]); | |
| psurge_set_ipi(i); | |
| } | |
| } | |
| } | |
| /* | |
| * Determine a quad card presence. We read the board ID register, we | |
| * force the data bus to change to something else, and we read it again. | |
| * It it's stable, then the register probably exist (ugh !) | |
| */ | |
| static int __init psurge_quad_probe(void) | |
| { | |
| int type; | |
| unsigned int i; | |
| type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID); | |
| if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS | |
| || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID)) | |
| return PSURGE_DUAL; | |
| /* looks OK, try a slightly more rigorous test */ | |
| /* bogus is not necessarily cacheline-aligned, | |
| though I don't suppose that really matters. -- paulus */ | |
| for (i = 0; i < 100; i++) { | |
| volatile u32 bogus[8]; | |
| bogus[(0+i)%8] = 0x00000000; | |
| bogus[(1+i)%8] = 0x55555555; | |
| bogus[(2+i)%8] = 0xFFFFFFFF; | |
| bogus[(3+i)%8] = 0xAAAAAAAA; | |
| bogus[(4+i)%8] = 0x33333333; | |
| bogus[(5+i)%8] = 0xCCCCCCCC; | |
| bogus[(6+i)%8] = 0xCCCCCCCC; | |
| bogus[(7+i)%8] = 0x33333333; | |
| wmb(); | |
| asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory"); | |
| mb(); | |
| if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID)) | |
| return PSURGE_DUAL; | |
| } | |
| return type; | |
| } | |
| static void __init psurge_quad_init(void) | |
| { | |
| int procbits; | |
| if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351); | |
| procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU); | |
| if (psurge_type == PSURGE_QUAD_ICEGRASS) | |
| PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits); | |
| else | |
| PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits); | |
| mdelay(33); | |
| out_8(psurge_sec_intr, ~0); | |
| PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits); | |
| PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits); | |
| if (psurge_type != PSURGE_QUAD_ICEGRASS) | |
| PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits); | |
| PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits); | |
| mdelay(33); | |
| PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits); | |
| mdelay(33); | |
| PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits); | |
| mdelay(33); | |
| } | |
| static int __init smp_psurge_probe(void) | |
| { | |
| int i, ncpus; | |
| /* We don't do SMP on the PPC601 -- paulus */ | |
| if (PVR_VER(mfspr(SPRN_PVR)) == 1) | |
| return 1; | |
| /* | |
| * The powersurge cpu board can be used in the generation | |
| * of powermacs that have a socket for an upgradeable cpu card, | |
| * including the 7500, 8500, 9500, 9600. | |
| * The device tree doesn't tell you if you have 2 cpus because | |
| * OF doesn't know anything about the 2nd processor. | |
| * Instead we look for magic bits in magic registers, | |
| * in the hammerhead memory controller in the case of the | |
| * dual-cpu powersurge board. -- paulus. | |
| */ | |
| if (find_devices("hammerhead") == NULL) | |
| return 1; | |
| hhead_base = ioremap(HAMMERHEAD_BASE, 0x800); | |
| quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024); | |
| psurge_sec_intr = hhead_base + HHEAD_SEC_INTR; | |
| psurge_type = psurge_quad_probe(); | |
| if (psurge_type != PSURGE_DUAL) { | |
| psurge_quad_init(); | |
| /* All released cards using this HW design have 4 CPUs */ | |
| ncpus = 4; | |
| } else { | |
| iounmap(quad_base); | |
| if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) { | |
| /* not a dual-cpu card */ | |
| iounmap(hhead_base); | |
| psurge_type = PSURGE_NONE; | |
| return 1; | |
| } | |
| ncpus = 2; | |
| } | |
| psurge_start = ioremap(PSURGE_START, 4); | |
| psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4); | |
| /* | |
| * This is necessary because OF doesn't know about the | |
| * secondary cpu(s), and thus there aren't nodes in the | |
| * device tree for them, and smp_setup_cpu_maps hasn't | |
| * set their bits in cpu_possible_map and cpu_present_map. | |
| */ | |
| if (ncpus > NR_CPUS) | |
| ncpus = NR_CPUS; | |
| for (i = 1; i < ncpus ; ++i) { | |
| cpu_set(i, cpu_present_map); | |
| cpu_set(i, cpu_possible_map); | |
| set_hard_smp_processor_id(i, i); | |
| } | |
| if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352); | |
| return ncpus; | |
| } | |
| static void __init smp_psurge_kick_cpu(int nr) | |
| { | |
| unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8; | |
| unsigned long a; | |
| int i; | |
| /* may need to flush here if secondary bats aren't setup */ | |
| for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32) | |
| asm volatile("dcbf 0,%0" : : "r" (a) : "memory"); | |
| asm volatile("sync"); | |
| if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353); | |
| out_be32(psurge_start, start); | |
| mb(); | |
| psurge_set_ipi(nr); | |
| /* | |
| * We can't use udelay here because the timebase is now frozen. | |
| */ | |
| for (i = 0; i < 2000; ++i) | |
| barrier(); | |
| psurge_clr_ipi(nr); | |
| if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354); | |
| } | |
| /* | |
| * With the dual-cpu powersurge board, the decrementers and timebases | |
| * of both cpus are frozen after the secondary cpu is started up, | |
| * until we give the secondary cpu another interrupt. This routine | |
| * uses this to get the timebases synchronized. | |
| * -- paulus. | |
| */ | |
| static void __init psurge_dual_sync_tb(int cpu_nr) | |
| { | |
| int t; | |
| set_dec(tb_ticks_per_jiffy); | |
| /* XXX fixme */ | |
| set_tb(0, 0); | |
| if (cpu_nr > 0) { | |
| mb(); | |
| sec_tb_reset = 1; | |
| return; | |
| } | |
| /* wait for the secondary to have reset its TB before proceeding */ | |
| for (t = 10000000; t > 0 && !sec_tb_reset; --t) | |
| ; | |
| /* now interrupt the secondary, starting both TBs */ | |
| psurge_set_ipi(1); | |
| } | |
| static struct irqaction psurge_irqaction = { | |
| .handler = psurge_primary_intr, | |
| .flags = IRQF_DISABLED, | |
| .mask = CPU_MASK_NONE, | |
| .name = "primary IPI", | |
| }; | |
| static void __init smp_psurge_setup_cpu(int cpu_nr) | |
| { | |
| if (cpu_nr == 0) { | |
| /* If we failed to start the second CPU, we should still | |
| * send it an IPI to start the timebase & DEC or we might | |
| * have them stuck. | |
| */ | |
| if (num_online_cpus() < 2) { | |
| if (psurge_type == PSURGE_DUAL) | |
| psurge_set_ipi(1); | |
| return; | |
| } | |
| /* reset the entry point so if we get another intr we won't | |
| * try to startup again */ | |
| out_be32(psurge_start, 0x100); | |
| if (setup_irq(30, &psurge_irqaction)) | |
| printk(KERN_ERR "Couldn't get primary IPI interrupt"); | |
| } | |
| if (psurge_type == PSURGE_DUAL) | |
| psurge_dual_sync_tb(cpu_nr); | |
| } | |
| void __init smp_psurge_take_timebase(void) | |
| { | |
| /* Dummy implementation */ | |
| } | |
| void __init smp_psurge_give_timebase(void) | |
| { | |
| /* Dummy implementation */ | |
| } | |
| /* PowerSurge-style Macs */ | |
| struct smp_ops_t psurge_smp_ops = { | |
| .message_pass = smp_psurge_message_pass, | |
| .probe = smp_psurge_probe, | |
| .kick_cpu = smp_psurge_kick_cpu, | |
| .setup_cpu = smp_psurge_setup_cpu, | |
| .give_timebase = smp_psurge_give_timebase, | |
| .take_timebase = smp_psurge_take_timebase, | |
| }; | |
| #endif /* CONFIG_PPC32 - actually powersurge support */ | |
| /* | |
| * Core 99 and later support | |
| */ | |
| static void (*pmac_tb_freeze)(int freeze); | |
| static u64 timebase; | |
| static int tb_req; | |
| static void smp_core99_give_timebase(void) | |
| { | |
| unsigned long flags; | |
| local_irq_save(flags); | |
| while(!tb_req) | |
| barrier(); | |
| tb_req = 0; | |
| (*pmac_tb_freeze)(1); | |
| mb(); | |
| timebase = get_tb(); | |
| mb(); | |
| while (timebase) | |
| barrier(); | |
| mb(); | |
| (*pmac_tb_freeze)(0); | |
| mb(); | |
| local_irq_restore(flags); | |
| } | |
| static void __devinit smp_core99_take_timebase(void) | |
| { | |
| unsigned long flags; | |
| local_irq_save(flags); | |
| tb_req = 1; | |
| mb(); | |
| while (!timebase) | |
| barrier(); | |
| mb(); | |
| set_tb(timebase >> 32, timebase & 0xffffffff); | |
| timebase = 0; | |
| mb(); | |
| set_dec(tb_ticks_per_jiffy/2); | |
| local_irq_restore(flags); | |
| } | |
| #ifdef CONFIG_PPC64 | |
| /* | |
| * G5s enable/disable the timebase via an i2c-connected clock chip. | |
| */ | |
| static struct pmac_i2c_bus *pmac_tb_clock_chip_host; | |
| static u8 pmac_tb_pulsar_addr; | |
| static void smp_core99_cypress_tb_freeze(int freeze) | |
| { | |
| u8 data; | |
| int rc; | |
| /* Strangely, the device-tree says address is 0xd2, but darwin | |
| * accesses 0xd0 ... | |
| */ | |
| pmac_i2c_setmode(pmac_tb_clock_chip_host, | |
| pmac_i2c_mode_combined); | |
| rc = pmac_i2c_xfer(pmac_tb_clock_chip_host, | |
| 0xd0 | pmac_i2c_read, | |
| 1, 0x81, &data, 1); | |
| if (rc != 0) | |
| goto bail; | |
| data = (data & 0xf3) | (freeze ? 0x00 : 0x0c); | |
| pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub); | |
| rc = pmac_i2c_xfer(pmac_tb_clock_chip_host, | |
| 0xd0 | pmac_i2c_write, | |
| 1, 0x81, &data, 1); | |
| bail: | |
| if (rc != 0) { | |
| printk("Cypress Timebase %s rc: %d\n", | |
| freeze ? "freeze" : "unfreeze", rc); | |
| panic("Timebase freeze failed !\n"); | |
| } | |
| } | |
| static void smp_core99_pulsar_tb_freeze(int freeze) | |
| { | |
| u8 data; | |
| int rc; | |
| pmac_i2c_setmode(pmac_tb_clock_chip_host, | |
| pmac_i2c_mode_combined); | |
| rc = pmac_i2c_xfer(pmac_tb_clock_chip_host, | |
| pmac_tb_pulsar_addr | pmac_i2c_read, | |
| 1, 0x2e, &data, 1); | |
| if (rc != 0) | |
| goto bail; | |
| data = (data & 0x88) | (freeze ? 0x11 : 0x22); | |
| pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub); | |
| rc = pmac_i2c_xfer(pmac_tb_clock_chip_host, | |
| pmac_tb_pulsar_addr | pmac_i2c_write, | |
| 1, 0x2e, &data, 1); | |
| bail: | |
| if (rc != 0) { | |
| printk(KERN_ERR "Pulsar Timebase %s rc: %d\n", | |
| freeze ? "freeze" : "unfreeze", rc); | |
| panic("Timebase freeze failed !\n"); | |
| } | |
| } | |
| static void __init smp_core99_setup_i2c_hwsync(int ncpus) | |
| { | |
| struct device_node *cc = NULL; | |
| struct device_node *p; | |
| const char *name = NULL; | |
| const u32 *reg; | |
| int ok; | |
| /* Look for the clock chip */ | |
| while ((cc = of_find_node_by_name(cc, "i2c-hwclock")) != NULL) { | |
| p = of_get_parent(cc); | |
| ok = p && device_is_compatible(p, "uni-n-i2c"); | |
| of_node_put(p); | |
| if (!ok) | |
| continue; | |
| pmac_tb_clock_chip_host = pmac_i2c_find_bus(cc); | |
| if (pmac_tb_clock_chip_host == NULL) | |
| continue; | |
| reg = get_property(cc, "reg", NULL); | |
| if (reg == NULL) | |
| continue; | |
| switch (*reg) { | |
| case 0xd2: | |
| if (device_is_compatible(cc,"pulsar-legacy-slewing")) { | |
| pmac_tb_freeze = smp_core99_pulsar_tb_freeze; | |
| pmac_tb_pulsar_addr = 0xd2; | |
| name = "Pulsar"; | |
| } else if (device_is_compatible(cc, "cy28508")) { | |
| pmac_tb_freeze = smp_core99_cypress_tb_freeze; | |
| name = "Cypress"; | |
| } | |
| break; | |
| case 0xd4: | |
| pmac_tb_freeze = smp_core99_pulsar_tb_freeze; | |
| pmac_tb_pulsar_addr = 0xd4; | |
| name = "Pulsar"; | |
| break; | |
| } | |
| if (pmac_tb_freeze != NULL) | |
| break; | |
| } | |
| if (pmac_tb_freeze != NULL) { | |
| /* Open i2c bus for synchronous access */ | |
| if (pmac_i2c_open(pmac_tb_clock_chip_host, 1)) { | |
| printk(KERN_ERR "Failed top open i2c bus for clock" | |
| " sync, fallback to software sync !\n"); | |
| goto no_i2c_sync; | |
| } | |
| printk(KERN_INFO "Processor timebase sync using %s i2c clock\n", | |
| name); | |
| return; | |
| } | |
| no_i2c_sync: | |
| pmac_tb_freeze = NULL; | |
| pmac_tb_clock_chip_host = NULL; | |
| } | |
| /* | |
| * Newer G5s uses a platform function | |
| */ | |
| static void smp_core99_pfunc_tb_freeze(int freeze) | |
| { | |
| struct device_node *cpus; | |
| struct pmf_args args; | |
| cpus = of_find_node_by_path("/cpus"); | |
| BUG_ON(cpus == NULL); | |
| args.count = 1; | |
| args.u[0].v = !freeze; | |
| pmf_call_function(cpus, "cpu-timebase", &args); | |
| of_node_put(cpus); | |
| } | |
| #else /* CONFIG_PPC64 */ | |
| /* | |
| * SMP G4 use a GPIO to enable/disable the timebase. | |
| */ | |
| static unsigned int core99_tb_gpio; /* Timebase freeze GPIO */ | |
| static void smp_core99_gpio_tb_freeze(int freeze) | |
| { | |
| if (freeze) | |
| pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4); | |
| else | |
| pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0); | |
| pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0); | |
| } | |
| #endif /* !CONFIG_PPC64 */ | |
| /* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */ | |
| volatile static long int core99_l2_cache; | |
| volatile static long int core99_l3_cache; | |
| static void __devinit core99_init_caches(int cpu) | |
| { | |
| #ifndef CONFIG_PPC64 | |
| if (!cpu_has_feature(CPU_FTR_L2CR)) | |
| return; | |
| if (cpu == 0) { | |
| core99_l2_cache = _get_L2CR(); | |
| printk("CPU0: L2CR is %lx\n", core99_l2_cache); | |
| } else { | |
| printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR()); | |
| _set_L2CR(0); | |
| _set_L2CR(core99_l2_cache); | |
| printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache); | |
| } | |
| if (!cpu_has_feature(CPU_FTR_L3CR)) | |
| return; | |
| if (cpu == 0){ | |
| core99_l3_cache = _get_L3CR(); | |
| printk("CPU0: L3CR is %lx\n", core99_l3_cache); | |
| } else { | |
| printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR()); | |
| _set_L3CR(0); | |
| _set_L3CR(core99_l3_cache); | |
| printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache); | |
| } | |
| #endif /* !CONFIG_PPC64 */ | |
| } | |
| static void __init smp_core99_setup(int ncpus) | |
| { | |
| #ifdef CONFIG_PPC64 | |
| /* i2c based HW sync on some G5s */ | |
| if (machine_is_compatible("PowerMac7,2") || | |
| machine_is_compatible("PowerMac7,3") || | |
| machine_is_compatible("RackMac3,1")) | |
| smp_core99_setup_i2c_hwsync(ncpus); | |
| /* pfunc based HW sync on recent G5s */ | |
| if (pmac_tb_freeze == NULL) { | |
| struct device_node *cpus = | |
| of_find_node_by_path("/cpus"); | |
| if (cpus && | |
| get_property(cpus, "platform-cpu-timebase", NULL)) { | |
| pmac_tb_freeze = smp_core99_pfunc_tb_freeze; | |
| printk(KERN_INFO "Processor timebase sync using" | |
| " platform function\n"); | |
| } | |
| } | |
| #else /* CONFIG_PPC64 */ | |
| /* GPIO based HW sync on ppc32 Core99 */ | |
| if (pmac_tb_freeze == NULL && !machine_is_compatible("MacRISC4")) { | |
| struct device_node *cpu; | |
| const u32 *tbprop = NULL; | |
| core99_tb_gpio = KL_GPIO_TB_ENABLE; /* default value */ | |
| cpu = of_find_node_by_type(NULL, "cpu"); | |
| if (cpu != NULL) { | |
| tbprop = get_property(cpu, "timebase-enable", NULL); | |
| if (tbprop) | |
| core99_tb_gpio = *tbprop; | |
| of_node_put(cpu); | |
| } | |
| pmac_tb_freeze = smp_core99_gpio_tb_freeze; | |
| printk(KERN_INFO "Processor timebase sync using" | |
| " GPIO 0x%02x\n", core99_tb_gpio); | |
| } | |
| #endif /* CONFIG_PPC64 */ | |
| /* No timebase sync, fallback to software */ | |
| if (pmac_tb_freeze == NULL) { | |
| smp_ops->give_timebase = smp_generic_give_timebase; | |
| smp_ops->take_timebase = smp_generic_take_timebase; | |
| printk(KERN_INFO "Processor timebase sync using software\n"); | |
| } | |
| #ifndef CONFIG_PPC64 | |
| { | |
| int i; | |
| /* XXX should get this from reg properties */ | |
| for (i = 1; i < ncpus; ++i) | |
| smp_hw_index[i] = i; | |
| } | |
| #endif | |
| /* 32 bits SMP can't NAP */ | |
| if (!machine_is_compatible("MacRISC4")) | |
| powersave_nap = 0; | |
| } | |
| static int __init smp_core99_probe(void) | |
| { | |
| struct device_node *cpus; | |
| int ncpus = 0; | |
| if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345); | |
| /* Count CPUs in the device-tree */ | |
| for (cpus = NULL; (cpus = of_find_node_by_type(cpus, "cpu")) != NULL;) | |
| ++ncpus; | |
| printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus); | |
| /* Nothing more to do if less than 2 of them */ | |
| if (ncpus <= 1) | |
| return 1; | |
| /* We need to perform some early initialisations before we can start | |
| * setting up SMP as we are running before initcalls | |
| */ | |
| pmac_pfunc_base_install(); | |
| pmac_i2c_init(); | |
| /* Setup various bits like timebase sync method, ability to nap, ... */ | |
| smp_core99_setup(ncpus); | |
| /* Install IPIs */ | |
| mpic_request_ipis(); | |
| /* Collect l2cr and l3cr values from CPU 0 */ | |
| core99_init_caches(0); | |
| return ncpus; | |
| } | |
| static void __devinit smp_core99_kick_cpu(int nr) | |
| { | |
| unsigned int save_vector; | |
| unsigned long target, flags; | |
| volatile unsigned int *vector | |
| = ((volatile unsigned int *)(KERNELBASE+0x100)); | |
| if (nr < 0 || nr > 3) | |
| return; | |
| if (ppc_md.progress) | |
| ppc_md.progress("smp_core99_kick_cpu", 0x346); | |
| local_irq_save(flags); | |
| local_irq_disable(); | |
| /* Save reset vector */ | |
| save_vector = *vector; | |
| /* Setup fake reset vector that does | |
| * b __secondary_start_pmac_0 + nr*8 - KERNELBASE | |
| */ | |
| target = (unsigned long) __secondary_start_pmac_0 + nr * 8; | |
| create_branch((unsigned long)vector, target, BRANCH_SET_LINK); | |
| /* Put some life in our friend */ | |
| pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0); | |
| /* FIXME: We wait a bit for the CPU to take the exception, I should | |
| * instead wait for the entry code to set something for me. Well, | |
| * ideally, all that crap will be done in prom.c and the CPU left | |
| * in a RAM-based wait loop like CHRP. | |
| */ | |
| mdelay(1); | |
| /* Restore our exception vector */ | |
| *vector = save_vector; | |
| flush_icache_range((unsigned long) vector, (unsigned long) vector + 4); | |
| local_irq_restore(flags); | |
| if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347); | |
| } | |
| static void __devinit smp_core99_setup_cpu(int cpu_nr) | |
| { | |
| /* Setup L2/L3 */ | |
| if (cpu_nr != 0) | |
| core99_init_caches(cpu_nr); | |
| /* Setup openpic */ | |
| mpic_setup_this_cpu(); | |
| if (cpu_nr == 0) { | |
| #ifdef CONFIG_PPC64 | |
| extern void g5_phy_disable_cpu1(void); | |
| /* Close i2c bus if it was used for tb sync */ | |
| if (pmac_tb_clock_chip_host) { | |
| pmac_i2c_close(pmac_tb_clock_chip_host); | |
| pmac_tb_clock_chip_host = NULL; | |
| } | |
| /* If we didn't start the second CPU, we must take | |
| * it off the bus | |
| */ | |
| if (machine_is_compatible("MacRISC4") && | |
| num_online_cpus() < 2) | |
| g5_phy_disable_cpu1(); | |
| #endif /* CONFIG_PPC64 */ | |
| if (ppc_md.progress) | |
| ppc_md.progress("core99_setup_cpu 0 done", 0x349); | |
| } | |
| } | |
| #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32) | |
| int smp_core99_cpu_disable(void) | |
| { | |
| cpu_clear(smp_processor_id(), cpu_online_map); | |
| /* XXX reset cpu affinity here */ | |
| mpic_cpu_set_priority(0xf); | |
| asm volatile("mtdec %0" : : "r" (0x7fffffff)); | |
| mb(); | |
| udelay(20); | |
| asm volatile("mtdec %0" : : "r" (0x7fffffff)); | |
| return 0; | |
| } | |
| extern void low_cpu_die(void) __attribute__((noreturn)); /* in sleep.S */ | |
| static int cpu_dead[NR_CPUS]; | |
| void cpu_die(void) | |
| { | |
| local_irq_disable(); | |
| cpu_dead[smp_processor_id()] = 1; | |
| mb(); | |
| low_cpu_die(); | |
| } | |
| void smp_core99_cpu_die(unsigned int cpu) | |
| { | |
| int timeout; | |
| timeout = 1000; | |
| while (!cpu_dead[cpu]) { | |
| if (--timeout == 0) { | |
| printk("CPU %u refused to die!\n", cpu); | |
| break; | |
| } | |
| msleep(1); | |
| } | |
| cpu_dead[cpu] = 0; | |
| } | |
| #endif | |
| /* Core99 Macs (dual G4s and G5s) */ | |
| struct smp_ops_t core99_smp_ops = { | |
| .message_pass = smp_mpic_message_pass, | |
| .probe = smp_core99_probe, | |
| .kick_cpu = smp_core99_kick_cpu, | |
| .setup_cpu = smp_core99_setup_cpu, | |
| .give_timebase = smp_core99_give_timebase, | |
| .take_timebase = smp_core99_take_timebase, | |
| #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32) | |
| .cpu_disable = smp_core99_cpu_disable, | |
| .cpu_die = smp_core99_cpu_die, | |
| #endif | |
| }; |