| /* | |
| * Board setup routines for the Force CPCI690 board. | |
| * | |
| * Author: Mark A. Greer <mgreer@mvista.com> | |
| * | |
| * 2003 (c) MontaVista Software, Inc. This file is licensed under | |
| * the terms of the GNU General Public License version 2. This programr | |
| * is licensed "as is" without any warranty of any kind, whether express | |
| * or implied. | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/pci.h> | |
| #include <linux/ide.h> | |
| #include <linux/irq.h> | |
| #include <linux/fs.h> | |
| #include <linux/seq_file.h> | |
| #include <linux/console.h> | |
| #include <linux/initrd.h> | |
| #include <linux/root_dev.h> | |
| #include <linux/mv643xx.h> | |
| #include <linux/platform_device.h> | |
| #include <asm/bootinfo.h> | |
| #include <asm/machdep.h> | |
| #include <asm/todc.h> | |
| #include <asm/time.h> | |
| #include <asm/mv64x60.h> | |
| #include <platforms/cpci690.h> | |
| #define BOARD_VENDOR "Force" | |
| #define BOARD_MACHINE "CPCI690" | |
| /* Set IDE controllers into Native mode? */ | |
| #define SET_PCI_IDE_NATIVE | |
| static struct mv64x60_handle bh; | |
| static void __iomem *cpci690_br_base; | |
| TODC_ALLOC(); | |
| static int __init | |
| cpci690_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) | |
| { | |
| struct pci_controller *hose = pci_bus_to_hose(dev->bus->number); | |
| if (hose->index == 0) { | |
| static char pci_irq_table[][4] = | |
| /* | |
| * PCI IDSEL/INTPIN->INTLINE | |
| * A B C D | |
| */ | |
| { | |
| { 90, 91, 88, 89 }, /* IDSEL 30/20 - Sentinel */ | |
| }; | |
| const long min_idsel = 20, max_idsel = 20, irqs_per_slot = 4; | |
| return PCI_IRQ_TABLE_LOOKUP; | |
| } else { | |
| static char pci_irq_table[][4] = | |
| /* | |
| * PCI IDSEL/INTPIN->INTLINE | |
| * A B C D | |
| */ | |
| { | |
| { 93, 94, 95, 92 }, /* IDSEL 28/18 - PMC slot 2 */ | |
| { 0, 0, 0, 0 }, /* IDSEL 29/19 - Not used */ | |
| { 94, 95, 92, 93 }, /* IDSEL 30/20 - PMC slot 1 */ | |
| }; | |
| const long min_idsel = 18, max_idsel = 20, irqs_per_slot = 4; | |
| return PCI_IRQ_TABLE_LOOKUP; | |
| } | |
| } | |
| #define GB (1024UL * 1024UL * 1024UL) | |
| static u32 | |
| cpci690_get_bus_freq(void) | |
| { | |
| if (boot_mem_size >= (1*GB)) /* bus speed based on mem size */ | |
| return 100000000; | |
| else | |
| return 133333333; | |
| } | |
| static const unsigned int cpu_750xx[32] = { /* 750FX & 750GX */ | |
| 0, 0, 2, 2, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,/* 0-15*/ | |
| 16, 17, 18, 19, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 0 /*16-31*/ | |
| }; | |
| static int | |
| cpci690_get_cpu_freq(void) | |
| { | |
| unsigned long pll_cfg; | |
| pll_cfg = (mfspr(SPRN_HID1) & 0xf8000000) >> 27; | |
| return cpci690_get_bus_freq() * cpu_750xx[pll_cfg]/2; | |
| } | |
| static void __init | |
| cpci690_setup_bridge(void) | |
| { | |
| struct mv64x60_setup_info si; | |
| int i; | |
| memset(&si, 0, sizeof(si)); | |
| si.phys_reg_base = CONFIG_MV64X60_NEW_BASE; | |
| si.pci_0.enable_bus = 1; | |
| si.pci_0.pci_io.cpu_base = CPCI690_PCI0_IO_START_PROC_ADDR; | |
| si.pci_0.pci_io.pci_base_hi = 0; | |
| si.pci_0.pci_io.pci_base_lo = CPCI690_PCI0_IO_START_PCI_ADDR; | |
| si.pci_0.pci_io.size = CPCI690_PCI0_IO_SIZE; | |
| si.pci_0.pci_io.swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_0.pci_mem[0].cpu_base = CPCI690_PCI0_MEM_START_PROC_ADDR; | |
| si.pci_0.pci_mem[0].pci_base_hi = CPCI690_PCI0_MEM_START_PCI_HI_ADDR; | |
| si.pci_0.pci_mem[0].pci_base_lo = CPCI690_PCI0_MEM_START_PCI_LO_ADDR; | |
| si.pci_0.pci_mem[0].size = CPCI690_PCI0_MEM_SIZE; | |
| si.pci_0.pci_mem[0].swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_0.pci_cmd_bits = 0; | |
| si.pci_0.latency_timer = 0x80; | |
| si.pci_1.enable_bus = 1; | |
| si.pci_1.pci_io.cpu_base = CPCI690_PCI1_IO_START_PROC_ADDR; | |
| si.pci_1.pci_io.pci_base_hi = 0; | |
| si.pci_1.pci_io.pci_base_lo = CPCI690_PCI1_IO_START_PCI_ADDR; | |
| si.pci_1.pci_io.size = CPCI690_PCI1_IO_SIZE; | |
| si.pci_1.pci_io.swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_1.pci_mem[0].cpu_base = CPCI690_PCI1_MEM_START_PROC_ADDR; | |
| si.pci_1.pci_mem[0].pci_base_hi = CPCI690_PCI1_MEM_START_PCI_HI_ADDR; | |
| si.pci_1.pci_mem[0].pci_base_lo = CPCI690_PCI1_MEM_START_PCI_LO_ADDR; | |
| si.pci_1.pci_mem[0].size = CPCI690_PCI1_MEM_SIZE; | |
| si.pci_1.pci_mem[0].swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_1.pci_cmd_bits = 0; | |
| si.pci_1.latency_timer = 0x80; | |
| for (i=0; i<MV64x60_CPU2MEM_WINDOWS; i++) { | |
| si.cpu_prot_options[i] = 0; | |
| si.cpu_snoop_options[i] = GT64260_CPU_SNOOP_WB; | |
| si.pci_0.acc_cntl_options[i] = | |
| GT64260_PCI_ACC_CNTL_DREADEN | | |
| GT64260_PCI_ACC_CNTL_RDPREFETCH | | |
| GT64260_PCI_ACC_CNTL_RDLINEPREFETCH | | |
| GT64260_PCI_ACC_CNTL_RDMULPREFETCH | | |
| GT64260_PCI_ACC_CNTL_SWAP_NONE | | |
| GT64260_PCI_ACC_CNTL_MBURST_32_BTYES; | |
| si.pci_0.snoop_options[i] = GT64260_PCI_SNOOP_WB; | |
| si.pci_1.acc_cntl_options[i] = | |
| GT64260_PCI_ACC_CNTL_DREADEN | | |
| GT64260_PCI_ACC_CNTL_RDPREFETCH | | |
| GT64260_PCI_ACC_CNTL_RDLINEPREFETCH | | |
| GT64260_PCI_ACC_CNTL_RDMULPREFETCH | | |
| GT64260_PCI_ACC_CNTL_SWAP_NONE | | |
| GT64260_PCI_ACC_CNTL_MBURST_32_BTYES; | |
| si.pci_1.snoop_options[i] = GT64260_PCI_SNOOP_WB; | |
| } | |
| /* Lookup PCI host bridges */ | |
| if (mv64x60_init(&bh, &si)) | |
| printk(KERN_ERR "Bridge initialization failed.\n"); | |
| pci_dram_offset = 0; /* System mem at same addr on PCI & cpu bus */ | |
| ppc_md.pci_swizzle = common_swizzle; | |
| ppc_md.pci_map_irq = cpci690_map_irq; | |
| ppc_md.pci_exclude_device = mv64x60_pci_exclude_device; | |
| mv64x60_set_bus(&bh, 0, 0); | |
| bh.hose_a->first_busno = 0; | |
| bh.hose_a->last_busno = 0xff; | |
| bh.hose_a->last_busno = pciauto_bus_scan(bh.hose_a, 0); | |
| bh.hose_b->first_busno = bh.hose_a->last_busno + 1; | |
| mv64x60_set_bus(&bh, 1, bh.hose_b->first_busno); | |
| bh.hose_b->last_busno = 0xff; | |
| bh.hose_b->last_busno = pciauto_bus_scan(bh.hose_b, | |
| bh.hose_b->first_busno); | |
| } | |
| static void __init | |
| cpci690_setup_peripherals(void) | |
| { | |
| /* Set up windows to CPLD, RTC/TODC, IPMI. */ | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_0_WIN, CPCI690_BR_BASE, | |
| CPCI690_BR_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_0_WIN); | |
| cpci690_br_base = ioremap(CPCI690_BR_BASE, CPCI690_BR_SIZE); | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_1_WIN, CPCI690_TODC_BASE, | |
| CPCI690_TODC_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_1_WIN); | |
| TODC_INIT(TODC_TYPE_MK48T35, 0, 0, | |
| ioremap(CPCI690_TODC_BASE, CPCI690_TODC_SIZE), 8); | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_2_WIN, CPCI690_IPMI_BASE, | |
| CPCI690_IPMI_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_2_WIN); | |
| mv64x60_set_bits(&bh, MV64x60_PCI0_ARBITER_CNTL, (1<<31)); | |
| mv64x60_set_bits(&bh, MV64x60_PCI1_ARBITER_CNTL, (1<<31)); | |
| mv64x60_set_bits(&bh, MV64x60_CPU_MASTER_CNTL, (1<<9)); /* Only 1 cpu */ | |
| /* | |
| * Turn off timer/counters. Not turning off watchdog timer because | |
| * can't read its reg on the 64260A so don't know if we'll be enabling | |
| * or disabling. | |
| */ | |
| mv64x60_clr_bits(&bh, MV64x60_TIMR_CNTR_0_3_CNTL, | |
| ((1<<0) | (1<<8) | (1<<16) | (1<<24))); | |
| mv64x60_clr_bits(&bh, GT64260_TIMR_CNTR_4_7_CNTL, | |
| ((1<<0) | (1<<8) | (1<<16) | (1<<24))); | |
| /* | |
| * Set MPSC Multiplex RMII | |
| * NOTE: ethernet driver modifies bit 0 and 1 | |
| */ | |
| mv64x60_write(&bh, GT64260_MPP_SERIAL_PORTS_MULTIPLEX, 0x00001102); | |
| #define GPP_EXTERNAL_INTERRUPTS \ | |
| ((1<<24) | (1<<25) | (1<<26) | (1<<27) | \ | |
| (1<<28) | (1<<29) | (1<<30) | (1<<31)) | |
| /* PCI interrupts are inputs */ | |
| mv64x60_clr_bits(&bh, MV64x60_GPP_IO_CNTL, GPP_EXTERNAL_INTERRUPTS); | |
| /* PCI interrupts are active low */ | |
| mv64x60_set_bits(&bh, MV64x60_GPP_LEVEL_CNTL, GPP_EXTERNAL_INTERRUPTS); | |
| /* Clear any pending interrupts for these inputs and enable them. */ | |
| mv64x60_write(&bh, MV64x60_GPP_INTR_CAUSE, ~GPP_EXTERNAL_INTERRUPTS); | |
| mv64x60_set_bits(&bh, MV64x60_GPP_INTR_MASK, GPP_EXTERNAL_INTERRUPTS); | |
| /* Route MPP interrupt inputs to GPP */ | |
| mv64x60_write(&bh, MV64x60_MPP_CNTL_2, 0x00000000); | |
| mv64x60_write(&bh, MV64x60_MPP_CNTL_3, 0x00000000); | |
| } | |
| static void __init | |
| cpci690_setup_arch(void) | |
| { | |
| if (ppc_md.progress) | |
| ppc_md.progress("cpci690_setup_arch: enter", 0); | |
| #ifdef CONFIG_BLK_DEV_INITRD | |
| if (initrd_start) | |
| ROOT_DEV = Root_RAM0; | |
| else | |
| #endif | |
| #ifdef CONFIG_ROOT_NFS | |
| ROOT_DEV = Root_NFS; | |
| #else | |
| ROOT_DEV = Root_SDA2; | |
| #endif | |
| if (ppc_md.progress) | |
| ppc_md.progress("cpci690_setup_arch: Enabling L2 cache", 0); | |
| /* Enable L2 and L3 caches (if 745x) */ | |
| _set_L2CR(_get_L2CR() | L2CR_L2E); | |
| _set_L3CR(_get_L3CR() | L3CR_L3E); | |
| if (ppc_md.progress) | |
| ppc_md.progress("cpci690_setup_arch: Initializing bridge", 0); | |
| cpci690_setup_bridge(); /* set up PCI bridge(s) */ | |
| cpci690_setup_peripherals(); /* set up chip selects/GPP/MPP etc */ | |
| if (ppc_md.progress) | |
| ppc_md.progress("cpci690_setup_arch: bridge init complete", 0); | |
| printk(KERN_INFO "%s %s port (C) 2003 MontaVista Software, Inc. " | |
| "(source@mvista.com)\n", BOARD_VENDOR, BOARD_MACHINE); | |
| if (ppc_md.progress) | |
| ppc_md.progress("cpci690_setup_arch: exit", 0); | |
| } | |
| /* Platform device data fixup routines. */ | |
| #if defined(CONFIG_SERIAL_MPSC) | |
| static void __init | |
| cpci690_fixup_mpsc_pdata(struct platform_device *pdev) | |
| { | |
| struct mpsc_pdata *pdata; | |
| pdata = (struct mpsc_pdata *)pdev->dev.platform_data; | |
| pdata->max_idle = 40; | |
| pdata->default_baud = CPCI690_MPSC_BAUD; | |
| pdata->brg_clk_src = CPCI690_MPSC_CLK_SRC; | |
| pdata->brg_clk_freq = cpci690_get_bus_freq(); | |
| } | |
| static int | |
| cpci690_platform_notify(struct device *dev) | |
| { | |
| static struct { | |
| char *bus_id; | |
| void ((*rtn)(struct platform_device *pdev)); | |
| } dev_map[] = { | |
| { MPSC_CTLR_NAME ".0", cpci690_fixup_mpsc_pdata }, | |
| { MPSC_CTLR_NAME ".1", cpci690_fixup_mpsc_pdata }, | |
| }; | |
| struct platform_device *pdev; | |
| int i; | |
| if (dev && dev->bus_id) | |
| for (i=0; i<ARRAY_SIZE(dev_map); i++) | |
| if (!strncmp(dev->bus_id, dev_map[i].bus_id, | |
| BUS_ID_SIZE)) { | |
| pdev = container_of(dev, | |
| struct platform_device, dev); | |
| dev_map[i].rtn(pdev); | |
| } | |
| return 0; | |
| } | |
| #endif | |
| static void | |
| cpci690_reset_board(void) | |
| { | |
| u32 i = 10000; | |
| local_irq_disable(); | |
| out_8((cpci690_br_base + CPCI690_BR_SW_RESET), 0x11); | |
| while (i != 0) i++; | |
| panic("restart failed\n"); | |
| } | |
| static void | |
| cpci690_restart(char *cmd) | |
| { | |
| cpci690_reset_board(); | |
| } | |
| static void | |
| cpci690_halt(void) | |
| { | |
| while (1); | |
| /* NOTREACHED */ | |
| } | |
| static void | |
| cpci690_power_off(void) | |
| { | |
| cpci690_halt(); | |
| /* NOTREACHED */ | |
| } | |
| static int | |
| cpci690_show_cpuinfo(struct seq_file *m) | |
| { | |
| char *s; | |
| seq_printf(m, "cpu MHz\t\t: %d\n", | |
| (cpci690_get_cpu_freq() + 500000) / 1000000); | |
| seq_printf(m, "bus MHz\t\t: %d\n", | |
| (cpci690_get_bus_freq() + 500000) / 1000000); | |
| seq_printf(m, "vendor\t\t: " BOARD_VENDOR "\n"); | |
| seq_printf(m, "machine\t\t: " BOARD_MACHINE "\n"); | |
| seq_printf(m, "FPGA Revision\t: %d\n", | |
| in_8(cpci690_br_base + CPCI690_BR_MEM_CTLR) >> 5); | |
| switch(bh.type) { | |
| case MV64x60_TYPE_GT64260A: | |
| s = "gt64260a"; | |
| break; | |
| case MV64x60_TYPE_GT64260B: | |
| s = "gt64260b"; | |
| break; | |
| case MV64x60_TYPE_MV64360: | |
| s = "mv64360"; | |
| break; | |
| case MV64x60_TYPE_MV64460: | |
| s = "mv64460"; | |
| break; | |
| default: | |
| s = "Unknown"; | |
| } | |
| seq_printf(m, "bridge type\t: %s\n", s); | |
| seq_printf(m, "bridge rev\t: 0x%x\n", bh.rev); | |
| #if defined(CONFIG_NOT_COHERENT_CACHE) | |
| seq_printf(m, "coherency\t: %s\n", "off"); | |
| #else | |
| seq_printf(m, "coherency\t: %s\n", "on"); | |
| #endif | |
| return 0; | |
| } | |
| static void __init | |
| cpci690_calibrate_decr(void) | |
| { | |
| ulong freq; | |
| freq = cpci690_get_bus_freq() / 4; | |
| printk(KERN_INFO "time_init: decrementer frequency = %lu.%.6lu MHz\n", | |
| freq/1000000, freq%1000000); | |
| tb_ticks_per_jiffy = freq / HZ; | |
| tb_to_us = mulhwu_scale_factor(freq, 1000000); | |
| } | |
| #if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB_MPSC) | |
| static void __init | |
| cpci690_map_io(void) | |
| { | |
| io_block_mapping(CONFIG_MV64X60_NEW_BASE, CONFIG_MV64X60_NEW_BASE, | |
| 128 * 1024, _PAGE_IO); | |
| } | |
| #endif | |
| void __init | |
| platform_init(unsigned long r3, unsigned long r4, unsigned long r5, | |
| unsigned long r6, unsigned long r7) | |
| { | |
| parse_bootinfo(find_bootinfo()); | |
| #ifdef CONFIG_BLK_DEV_INITRD | |
| /* take care of initrd if we have one */ | |
| if (r4) { | |
| initrd_start = r4 + KERNELBASE; | |
| initrd_end = r5 + KERNELBASE; | |
| } | |
| #endif /* CONFIG_BLK_DEV_INITRD */ | |
| isa_mem_base = 0; | |
| ppc_md.setup_arch = cpci690_setup_arch; | |
| ppc_md.show_cpuinfo = cpci690_show_cpuinfo; | |
| ppc_md.init_IRQ = gt64260_init_irq; | |
| ppc_md.get_irq = gt64260_get_irq; | |
| ppc_md.restart = cpci690_restart; | |
| ppc_md.power_off = cpci690_power_off; | |
| ppc_md.halt = cpci690_halt; | |
| ppc_md.time_init = todc_time_init; | |
| ppc_md.set_rtc_time = todc_set_rtc_time; | |
| ppc_md.get_rtc_time = todc_get_rtc_time; | |
| ppc_md.nvram_read_val = todc_direct_read_val; | |
| ppc_md.nvram_write_val = todc_direct_write_val; | |
| ppc_md.calibrate_decr = cpci690_calibrate_decr; | |
| #if defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB_MPSC) | |
| ppc_md.setup_io_mappings = cpci690_map_io; | |
| #ifdef CONFIG_SERIAL_TEXT_DEBUG | |
| ppc_md.progress = mv64x60_mpsc_progress; | |
| mv64x60_progress_init(CONFIG_MV64X60_NEW_BASE); | |
| #endif /* CONFIG_SERIAL_TEXT_DEBUG */ | |
| #endif /* defined(CONFIG_SERIAL_TEXT_DEBUG) || defined(CONFIG_KGDB_MPSC) */ | |
| #if defined(CONFIG_SERIAL_MPSC) | |
| platform_notify = cpci690_platform_notify; | |
| #endif | |
| } |