| /* | |
| * Board setup routines for the Artesyn Katana cPCI boards. | |
| * | |
| * Author: Tim Montgomery <timm@artesyncp.com> | |
| * Maintained by: Mark A. Greer <mgreer@mvista.com> | |
| * | |
| * Based on code done by Rabeeh Khoury - rabeeh@galileo.co.il | |
| * Based on code done by - Mark A. Greer <mgreer@mvista.com> | |
| * | |
| * This program is free software; you can redistribute it and/or modify it | |
| * under the terms of the GNU General Public License as published by the | |
| * Free Software Foundation; either version 2 of the License, or (at your | |
| * option) any later version. | |
| */ | |
| /* | |
| * Supports the Artesyn 750i, 752i, and 3750. The 752i is virtually identical | |
| * to the 750i except that it has an mv64460 bridge. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/pci.h> | |
| #include <linux/kdev_t.h> | |
| #include <linux/console.h> | |
| #include <linux/initrd.h> | |
| #include <linux/root_dev.h> | |
| #include <linux/delay.h> | |
| #include <linux/seq_file.h> | |
| #include <linux/mtd/physmap.h> | |
| #include <linux/mv643xx.h> | |
| #include <linux/platform_device.h> | |
| #ifdef CONFIG_BOOTIMG | |
| #include <linux/bootimg.h> | |
| #endif | |
| #include <asm/io.h> | |
| #include <asm/unistd.h> | |
| #include <asm/page.h> | |
| #include <asm/time.h> | |
| #include <asm/smp.h> | |
| #include <asm/todc.h> | |
| #include <asm/bootinfo.h> | |
| #include <asm/ppcboot.h> | |
| #include <asm/mv64x60.h> | |
| #include <platforms/katana.h> | |
| #include <asm/machdep.h> | |
| static struct mv64x60_handle bh; | |
| static katana_id_t katana_id; | |
| static void __iomem *cpld_base; | |
| static void __iomem *sram_base; | |
| static u32 katana_flash_size_0; | |
| static u32 katana_flash_size_1; | |
| static u32 katana_bus_frequency; | |
| static struct pci_controller katana_hose_a; | |
| unsigned char __res[sizeof(bd_t)]; | |
| /* PCI Interrupt routing */ | |
| static int __init | |
| katana_irq_lookup_750i(unsigned char idsel, unsigned char pin) | |
| { | |
| static char pci_irq_table[][4] = { | |
| /* | |
| * PCI IDSEL/INTPIN->INTLINE | |
| * A B C D | |
| */ | |
| /* IDSEL 4 (PMC 1) */ | |
| { KATANA_PCI_INTB_IRQ_750i, KATANA_PCI_INTC_IRQ_750i, | |
| KATANA_PCI_INTD_IRQ_750i, KATANA_PCI_INTA_IRQ_750i }, | |
| /* IDSEL 5 (PMC 2) */ | |
| { KATANA_PCI_INTC_IRQ_750i, KATANA_PCI_INTD_IRQ_750i, | |
| KATANA_PCI_INTA_IRQ_750i, KATANA_PCI_INTB_IRQ_750i }, | |
| /* IDSEL 6 (T8110) */ | |
| {KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 }, | |
| /* IDSEL 7 (unused) */ | |
| {0, 0, 0, 0 }, | |
| /* IDSEL 8 (Intel 82544) (752i only but doesn't harm 750i) */ | |
| {KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 }, | |
| }; | |
| const long min_idsel = 4, max_idsel = 8, irqs_per_slot = 4; | |
| return PCI_IRQ_TABLE_LOOKUP; | |
| } | |
| static int __init | |
| katana_irq_lookup_3750(unsigned char idsel, unsigned char pin) | |
| { | |
| static char pci_irq_table[][4] = { | |
| /* | |
| * PCI IDSEL/INTPIN->INTLINE | |
| * A B C D | |
| */ | |
| { KATANA_PCI_INTA_IRQ_3750, 0, 0, 0 }, /* IDSEL 3 (BCM5691) */ | |
| { KATANA_PCI_INTB_IRQ_3750, 0, 0, 0 }, /* IDSEL 4 (MV64360 #2)*/ | |
| { KATANA_PCI_INTC_IRQ_3750, 0, 0, 0 }, /* IDSEL 5 (MV64360 #3)*/ | |
| }; | |
| const long min_idsel = 3, max_idsel = 5, irqs_per_slot = 4; | |
| return PCI_IRQ_TABLE_LOOKUP; | |
| } | |
| static int __init | |
| katana_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) | |
| { | |
| switch (katana_id) { | |
| case KATANA_ID_750I: | |
| case KATANA_ID_752I: | |
| return katana_irq_lookup_750i(idsel, pin); | |
| case KATANA_ID_3750: | |
| return katana_irq_lookup_3750(idsel, pin); | |
| default: | |
| printk(KERN_ERR "Bogus board ID\n"); | |
| return 0; | |
| } | |
| } | |
| /* Board info retrieval routines */ | |
| void __init | |
| katana_get_board_id(void) | |
| { | |
| switch (in_8(cpld_base + KATANA_CPLD_PRODUCT_ID)) { | |
| case KATANA_PRODUCT_ID_3750: | |
| katana_id = KATANA_ID_3750; | |
| break; | |
| case KATANA_PRODUCT_ID_750i: | |
| katana_id = KATANA_ID_750I; | |
| break; | |
| case KATANA_PRODUCT_ID_752i: | |
| katana_id = KATANA_ID_752I; | |
| break; | |
| default: | |
| printk(KERN_ERR "Unsupported board\n"); | |
| } | |
| } | |
| int __init | |
| katana_get_proc_num(void) | |
| { | |
| u16 val; | |
| u8 save_exclude; | |
| static int proc = -1; | |
| static u8 first_time = 1; | |
| if (first_time) { | |
| if (katana_id != KATANA_ID_3750) | |
| proc = 0; | |
| else { | |
| save_exclude = mv64x60_pci_exclude_bridge; | |
| mv64x60_pci_exclude_bridge = 0; | |
| early_read_config_word(bh.hose_b, 0, | |
| PCI_DEVFN(0,0), PCI_DEVICE_ID, &val); | |
| mv64x60_pci_exclude_bridge = save_exclude; | |
| switch(val) { | |
| case PCI_DEVICE_ID_KATANA_3750_PROC0: | |
| proc = 0; | |
| break; | |
| case PCI_DEVICE_ID_KATANA_3750_PROC1: | |
| proc = 1; | |
| break; | |
| case PCI_DEVICE_ID_KATANA_3750_PROC2: | |
| proc = 2; | |
| break; | |
| default: | |
| printk(KERN_ERR "Bogus Device ID\n"); | |
| } | |
| } | |
| first_time = 0; | |
| } | |
| return proc; | |
| } | |
| static inline int | |
| katana_is_monarch(void) | |
| { | |
| return in_8(cpld_base + KATANA_CPLD_BD_CFG_3) & | |
| KATANA_CPLD_BD_CFG_3_MONARCH; | |
| } | |
| static void __init | |
| katana_setup_bridge(void) | |
| { | |
| struct pci_controller hose; | |
| struct mv64x60_setup_info si; | |
| void __iomem *vaddr; | |
| int i; | |
| u32 v; | |
| u16 val, type; | |
| u8 save_exclude; | |
| /* | |
| * Some versions of the Katana firmware mistakenly change the vendor | |
| * & device id fields in the bridge's pci device (visible via pci | |
| * config accesses). This breaks mv64x60_init() because those values | |
| * are used to identify the type of bridge that's there. Artesyn | |
| * claims that the subsystem vendor/device id's will have the correct | |
| * Marvell values so this code puts back the correct values from there. | |
| */ | |
| memset(&hose, 0, sizeof(hose)); | |
| vaddr = ioremap(CONFIG_MV64X60_NEW_BASE, MV64x60_INTERNAL_SPACE_SIZE); | |
| setup_indirect_pci_nomap(&hose, vaddr + MV64x60_PCI0_CONFIG_ADDR, | |
| vaddr + MV64x60_PCI0_CONFIG_DATA); | |
| save_exclude = mv64x60_pci_exclude_bridge; | |
| mv64x60_pci_exclude_bridge = 0; | |
| early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID, &val); | |
| if (val != PCI_VENDOR_ID_MARVELL) { | |
| early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), | |
| PCI_SUBSYSTEM_VENDOR_ID, &val); | |
| early_write_config_word(&hose, 0, PCI_DEVFN(0, 0), | |
| PCI_VENDOR_ID, val); | |
| early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), | |
| PCI_SUBSYSTEM_ID, &val); | |
| early_write_config_word(&hose, 0, PCI_DEVFN(0, 0), | |
| PCI_DEVICE_ID, val); | |
| } | |
| /* | |
| * While we're in here, set the hotswap register correctly. | |
| * Turn off blue LED; mask ENUM#, clear insertion & extraction bits. | |
| */ | |
| early_read_config_dword(&hose, 0, PCI_DEVFN(0, 0), | |
| MV64360_PCICFG_CPCI_HOTSWAP, &v); | |
| v &= ~(1<<19); | |
| v |= ((1<<17) | (1<<22) | (1<<23)); | |
| early_write_config_dword(&hose, 0, PCI_DEVFN(0, 0), | |
| MV64360_PCICFG_CPCI_HOTSWAP, v); | |
| /* While we're at it, grab the bridge type for later */ | |
| early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_DEVICE_ID, &type); | |
| mv64x60_pci_exclude_bridge = save_exclude; | |
| iounmap(vaddr); | |
| memset(&si, 0, sizeof(si)); | |
| si.phys_reg_base = CONFIG_MV64X60_NEW_BASE; | |
| si.pci_1.enable_bus = 1; | |
| si.pci_1.pci_io.cpu_base = KATANA_PCI1_IO_START_PROC_ADDR; | |
| si.pci_1.pci_io.pci_base_hi = 0; | |
| si.pci_1.pci_io.pci_base_lo = KATANA_PCI1_IO_START_PCI_ADDR; | |
| si.pci_1.pci_io.size = KATANA_PCI1_IO_SIZE; | |
| si.pci_1.pci_io.swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_1.pci_mem[0].cpu_base = KATANA_PCI1_MEM_START_PROC_ADDR; | |
| si.pci_1.pci_mem[0].pci_base_hi = KATANA_PCI1_MEM_START_PCI_HI_ADDR; | |
| si.pci_1.pci_mem[0].pci_base_lo = KATANA_PCI1_MEM_START_PCI_LO_ADDR; | |
| si.pci_1.pci_mem[0].size = KATANA_PCI1_MEM_SIZE; | |
| si.pci_1.pci_mem[0].swap = MV64x60_CPU2PCI_SWAP_NONE; | |
| si.pci_1.pci_cmd_bits = 0; | |
| si.pci_1.latency_timer = 0x80; | |
| for (i = 0; i < MV64x60_CPU2MEM_WINDOWS; i++) { | |
| #if defined(CONFIG_NOT_COHERENT_CACHE) | |
| si.cpu_prot_options[i] = 0; | |
| si.enet_options[i] = MV64360_ENET2MEM_SNOOP_NONE; | |
| si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_NONE; | |
| si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_NONE; | |
| si.pci_1.acc_cntl_options[i] = | |
| MV64360_PCI_ACC_CNTL_SNOOP_NONE | | |
| MV64360_PCI_ACC_CNTL_SWAP_NONE | | |
| MV64360_PCI_ACC_CNTL_MBURST_128_BYTES | | |
| MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES; | |
| #else | |
| si.cpu_prot_options[i] = 0; | |
| si.enet_options[i] = MV64360_ENET2MEM_SNOOP_WB; | |
| si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_WB; | |
| si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_WB; | |
| si.pci_1.acc_cntl_options[i] = | |
| MV64360_PCI_ACC_CNTL_SNOOP_WB | | |
| MV64360_PCI_ACC_CNTL_SWAP_NONE | | |
| MV64360_PCI_ACC_CNTL_MBURST_32_BYTES | | |
| ((type == PCI_DEVICE_ID_MARVELL_MV64360) ? | |
| MV64360_PCI_ACC_CNTL_RDSIZE_32_BYTES : | |
| MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES); | |
| #endif | |
| } | |
| /* Lookup PCI host bridges */ | |
| if (mv64x60_init(&bh, &si)) | |
| printk(KERN_WARNING "Bridge initialization failed.\n"); | |
| pci_dram_offset = 0; /* sys mem at same addr on PCI & cpu bus */ | |
| ppc_md.pci_swizzle = common_swizzle; | |
| ppc_md.pci_map_irq = katana_map_irq; | |
| ppc_md.pci_exclude_device = mv64x60_pci_exclude_device; | |
| mv64x60_set_bus(&bh, 1, 0); | |
| bh.hose_b->first_busno = 0; | |
| bh.hose_b->last_busno = 0xff; | |
| /* | |
| * Need to access hotswap reg which is in the pci config area of the | |
| * bridge's hose 0. Note that pcibios_alloc_controller() can't be used | |
| * to alloc hose_a b/c that would make hose 0 known to the generic | |
| * pci code which we don't want. | |
| */ | |
| bh.hose_a = &katana_hose_a; | |
| setup_indirect_pci_nomap(bh.hose_a, | |
| bh.v_base + MV64x60_PCI0_CONFIG_ADDR, | |
| bh.v_base + MV64x60_PCI0_CONFIG_DATA); | |
| } | |
| /* Bridge & platform setup routines */ | |
| void __init | |
| katana_intr_setup(void) | |
| { | |
| if (bh.type == MV64x60_TYPE_MV64460) /* As per instns from Marvell */ | |
| mv64x60_clr_bits(&bh, MV64x60_CPU_MASTER_CNTL, 1 << 15); | |
| /* MPP 8, 9, and 10 */ | |
| mv64x60_clr_bits(&bh, MV64x60_MPP_CNTL_1, 0xfff); | |
| /* MPP 14 */ | |
| if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) | |
| mv64x60_clr_bits(&bh, MV64x60_MPP_CNTL_1, 0x0f000000); | |
| /* | |
| * Define GPP 8,9,and 10 interrupt polarity as active low | |
| * input signal and level triggered | |
| */ | |
| mv64x60_set_bits(&bh, MV64x60_GPP_LEVEL_CNTL, 0x700); | |
| mv64x60_clr_bits(&bh, MV64x60_GPP_IO_CNTL, 0x700); | |
| if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) { | |
| mv64x60_set_bits(&bh, MV64x60_GPP_LEVEL_CNTL, (1<<14)); | |
| mv64x60_clr_bits(&bh, MV64x60_GPP_IO_CNTL, (1<<14)); | |
| } | |
| /* Config GPP intr ctlr to respond to level trigger */ | |
| mv64x60_set_bits(&bh, MV64x60_COMM_ARBITER_CNTL, (1<<10)); | |
| if (bh.type == MV64x60_TYPE_MV64360) { | |
| /* Erratum FEr PCI-#9 */ | |
| mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, | |
| (1<<4) | (1<<5) | (1<<6) | (1<<7)); | |
| mv64x60_set_bits(&bh, MV64x60_PCI1_CMD, (1<<8) | (1<<9)); | |
| } else { | |
| mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, (1<<6) | (1<<7)); | |
| mv64x60_set_bits(&bh, MV64x60_PCI1_CMD, | |
| (1<<4) | (1<<5) | (1<<8) | (1<<9)); | |
| } | |
| /* | |
| * Dismiss and then enable interrupt on GPP interrupt cause | |
| * for CPU #0 | |
| */ | |
| mv64x60_write(&bh, MV64x60_GPP_INTR_CAUSE, ~0x700); | |
| mv64x60_set_bits(&bh, MV64x60_GPP_INTR_MASK, 0x700); | |
| if ((katana_id == KATANA_ID_750I) || (katana_id == KATANA_ID_752I)) { | |
| mv64x60_write(&bh, MV64x60_GPP_INTR_CAUSE, ~(1<<14)); | |
| mv64x60_set_bits(&bh, MV64x60_GPP_INTR_MASK, (1<<14)); | |
| } | |
| /* | |
| * Dismiss and then enable interrupt on CPU #0 high cause reg | |
| * BIT25 summarizes GPP interrupts 8-15 | |
| */ | |
| mv64x60_set_bits(&bh, MV64360_IC_CPU0_INTR_MASK_HI, (1<<25)); | |
| } | |
| void __init | |
| katana_setup_peripherals(void) | |
| { | |
| u32 base; | |
| /* Set up windows for boot CS, soldered & socketed flash, and CPLD */ | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2BOOT_WIN, | |
| KATANA_BOOT_WINDOW_BASE, KATANA_BOOT_WINDOW_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2BOOT_WIN); | |
| /* Assume firmware set up window sizes correctly for dev 0 & 1 */ | |
| mv64x60_get_32bit_window(&bh, MV64x60_CPU2DEV_0_WIN, &base, | |
| &katana_flash_size_0); | |
| if (katana_flash_size_0 > 0) { | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_0_WIN, | |
| KATANA_SOLDERED_FLASH_BASE, katana_flash_size_0, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_0_WIN); | |
| } | |
| mv64x60_get_32bit_window(&bh, MV64x60_CPU2DEV_1_WIN, &base, | |
| &katana_flash_size_1); | |
| if (katana_flash_size_1 > 0) { | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_1_WIN, | |
| (KATANA_SOLDERED_FLASH_BASE + katana_flash_size_0), | |
| katana_flash_size_1, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_1_WIN); | |
| } | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_2_WIN, | |
| KATANA_SOCKET_BASE, KATANA_SOCKETED_FLASH_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_2_WIN); | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2DEV_3_WIN, | |
| KATANA_CPLD_BASE, KATANA_CPLD_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2DEV_3_WIN); | |
| cpld_base = ioremap(KATANA_CPLD_BASE, KATANA_CPLD_SIZE); | |
| mv64x60_set_32bit_window(&bh, MV64x60_CPU2SRAM_WIN, | |
| KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE, 0); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_CPU2SRAM_WIN); | |
| sram_base = ioremap(KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE); | |
| /* Set up Enet->SRAM window */ | |
| mv64x60_set_32bit_window(&bh, MV64x60_ENET2MEM_4_WIN, | |
| KATANA_INTERNAL_SRAM_BASE, MV64360_SRAM_SIZE, 0x2); | |
| bh.ci->enable_window_32bit(&bh, MV64x60_ENET2MEM_4_WIN); | |
| /* Give enet r/w access to memory region */ | |
| mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_0, (0x3 << (4 << 1))); | |
| mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_1, (0x3 << (4 << 1))); | |
| mv64x60_set_bits(&bh, MV64360_ENET2MEM_ACC_PROT_2, (0x3 << (4 << 1))); | |
| mv64x60_clr_bits(&bh, MV64x60_PCI1_PCI_DECODE_CNTL, (1 << 3)); | |
| mv64x60_clr_bits(&bh, MV64x60_TIMR_CNTR_0_3_CNTL, | |
| ((1 << 0) | (1 << 8) | (1 << 16) | (1 << 24))); | |
| /* Must wait until window set up before retrieving board id */ | |
| katana_get_board_id(); | |
| /* Enumerate pci bus (must know board id before getting proc number) */ | |
| if (katana_get_proc_num() == 0) | |
| bh.hose_b->last_busno = pciauto_bus_scan(bh.hose_b, 0); | |
| #if defined(CONFIG_NOT_COHERENT_CACHE) | |
| mv64x60_write(&bh, MV64360_SRAM_CONFIG, 0x00160000); | |
| #else | |
| mv64x60_write(&bh, MV64360_SRAM_CONFIG, 0x001600b2); | |
| #endif | |
| /* | |
| * Setting the SRAM to 0. Note that this generates parity errors on | |
| * internal data path in SRAM since it's first time accessing it | |
| * while after reset it's not configured. | |
| */ | |
| memset(sram_base, 0, MV64360_SRAM_SIZE); | |
| /* Only processor zero [on 3750] is an PCI interrupt controller */ | |
| if (katana_get_proc_num() == 0) | |
| katana_intr_setup(); | |
| } | |
| static void __init | |
| katana_enable_ipmi(void) | |
| { | |
| u8 reset_out; | |
| /* Enable access to IPMI ctlr by clearing IPMI PORTSEL bit in CPLD */ | |
| reset_out = in_8(cpld_base + KATANA_CPLD_RESET_OUT); | |
| reset_out &= ~KATANA_CPLD_RESET_OUT_PORTSEL; | |
| out_8(cpld_base + KATANA_CPLD_RESET_OUT, reset_out); | |
| } | |
| static void __init | |
| katana_setup_arch(void) | |
| { | |
| if (ppc_md.progress) | |
| ppc_md.progress("katana_setup_arch: enter", 0); | |
| set_tb(0, 0); | |
| #ifdef CONFIG_BLK_DEV_INITRD | |
| if (initrd_start) | |
| ROOT_DEV = Root_RAM0; | |
| else | |
| #endif | |
| #ifdef CONFIG_ROOT_NFS | |
| ROOT_DEV = Root_NFS; | |
| #else | |
| ROOT_DEV = Root_SDA2; | |
| #endif | |
| /* | |
| * Set up the L2CR register. | |
| * | |
| * 750FX has only L2E, L2PE (bits 2-8 are reserved) | |
| * DD2.0 has bug that requires the L2 to be in WRT mode | |
| * avoid dirty data in cache | |
| */ | |
| if (PVR_REV(mfspr(SPRN_PVR)) == 0x0200) { | |
| printk(KERN_INFO "DD2.0 detected. Setting L2 cache" | |
| "to Writethrough mode\n"); | |
| _set_L2CR(L2CR_L2E | L2CR_L2PE | L2CR_L2WT); | |
| } else | |
| _set_L2CR(L2CR_L2E | L2CR_L2PE); | |
| if (ppc_md.progress) | |
| ppc_md.progress("katana_setup_arch: calling setup_bridge", 0); | |
| katana_setup_bridge(); | |
| katana_setup_peripherals(); | |
| katana_enable_ipmi(); | |
| katana_bus_frequency = katana_bus_freq(cpld_base); | |
| printk(KERN_INFO "Artesyn Communication Products, LLC - Katana(TM)\n"); | |
| if (ppc_md.progress) | |
| ppc_md.progress("katana_setup_arch: exit", 0); | |
| } | |
| void | |
| katana_fixup_resources(struct pci_dev *dev) | |
| { | |
| u16 v16; | |
| pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, L1_CACHE_BYTES>>2); | |
| pci_read_config_word(dev, PCI_COMMAND, &v16); | |
| v16 |= PCI_COMMAND_INVALIDATE | PCI_COMMAND_FAST_BACK; | |
| pci_write_config_word(dev, PCI_COMMAND, v16); | |
| } | |
| static const unsigned int cpu_750xx[32] = { /* 750FX & 750GX */ | |
| 0, 0, 2, 2, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,/* 0-15*/ | |
| 16, 17, 18, 19, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 0 /*16-31*/ | |
| }; | |
| static int | |
| katana_get_cpu_freq(void) | |
| { | |
| unsigned long pll_cfg; | |
| pll_cfg = (mfspr(SPRN_HID1) & 0xf8000000) >> 27; | |
| return katana_bus_frequency * cpu_750xx[pll_cfg]/2; | |
| } | |
| /* Platform device data fixup routines. */ | |
| #if defined(CONFIG_SERIAL_MPSC) | |
| static void __init | |
| katana_fixup_mpsc_pdata(struct platform_device *pdev) | |
| { | |
| struct mpsc_pdata *pdata = (struct mpsc_pdata *)pdev->dev.platform_data; | |
| bd_t *bdp = (bd_t *)__res; | |
| if (bdp->bi_baudrate) | |
| pdata->default_baud = bdp->bi_baudrate; | |
| else | |
| pdata->default_baud = KATANA_DEFAULT_BAUD; | |
| pdata->max_idle = 40; | |
| pdata->brg_clk_src = KATANA_MPSC_CLK_SRC; | |
| /* | |
| * TCLK (not SysCLk) is routed to BRG, then to the MPSC. On most parts, | |
| * TCLK == SysCLK but on 64460, they are separate pins. | |
| * SysCLK can go up to 200 MHz but TCLK can only go up to 133 MHz. | |
| */ | |
| pdata->brg_clk_freq = min(katana_bus_frequency, MV64x60_TCLK_FREQ_MAX); | |
| } | |
| #endif | |
| #if defined(CONFIG_MV643XX_ETH) | |
| static void __init | |
| katana_fixup_eth_pdata(struct platform_device *pdev) | |
| { | |
| struct mv643xx_eth_platform_data *eth_pd; | |
| static u16 phy_addr[] = { | |
| KATANA_ETH0_PHY_ADDR, | |
| KATANA_ETH1_PHY_ADDR, | |
| KATANA_ETH2_PHY_ADDR, | |
| }; | |
| eth_pd = pdev->dev.platform_data; | |
| eth_pd->force_phy_addr = 1; | |
| eth_pd->phy_addr = phy_addr[pdev->id]; | |
| eth_pd->tx_queue_size = KATANA_ETH_TX_QUEUE_SIZE; | |
| eth_pd->rx_queue_size = KATANA_ETH_RX_QUEUE_SIZE; | |
| } | |
| #endif | |
| #if defined(CONFIG_SYSFS) | |
| static void __init | |
| katana_fixup_mv64xxx_pdata(struct platform_device *pdev) | |
| { | |
| struct mv64xxx_pdata *pdata = (struct mv64xxx_pdata *) | |
| pdev->dev.platform_data; | |
| /* Katana supports the mv64xxx hotswap register */ | |
| pdata->hs_reg_valid = 1; | |
| } | |
| #endif | |
| static int | |
| katana_platform_notify(struct device *dev) | |
| { | |
| static struct { | |
| char *bus_id; | |
| void ((*rtn)(struct platform_device *pdev)); | |
| } dev_map[] = { | |
| #if defined(CONFIG_SERIAL_MPSC) | |
| { MPSC_CTLR_NAME ".0", katana_fixup_mpsc_pdata }, | |
| { MPSC_CTLR_NAME ".1", katana_fixup_mpsc_pdata }, | |
| #endif | |
| #if defined(CONFIG_MV643XX_ETH) | |
| { MV643XX_ETH_NAME ".0", katana_fixup_eth_pdata }, | |
| { MV643XX_ETH_NAME ".1", katana_fixup_eth_pdata }, | |
| { MV643XX_ETH_NAME ".2", katana_fixup_eth_pdata }, | |
| #endif | |
| #if defined(CONFIG_SYSFS) | |
| { MV64XXX_DEV_NAME ".0", katana_fixup_mv64xxx_pdata }, | |
| #endif | |
| }; | |
| struct platform_device *pdev; | |
| int i; | |
| if (dev && dev->bus_id) | |
| for (i=0; i<ARRAY_SIZE(dev_map); i++) | |
| if (!strncmp(dev->bus_id, dev_map[i].bus_id, | |
| BUS_ID_SIZE)) { | |
| pdev = container_of(dev, | |
| struct platform_device, dev); | |
| dev_map[i].rtn(pdev); | |
| } | |
| return 0; | |
| } | |
| #ifdef CONFIG_MTD_PHYSMAP | |
| #ifndef MB | |
| #define MB (1 << 20) | |
| #endif | |
| /* | |
| * MTD Layout depends on amount of soldered FLASH in system. Sizes in MB. | |
| * | |
| * FLASH Amount: 128 64 32 16 | |
| * ------------- --- -- -- -- | |
| * Monitor: 1 1 1 1 | |
| * Primary Kernel: 1.5 1.5 1.5 1.5 | |
| * Primary fs: 30 30 <end> <end> | |
| * Secondary Kernel: 1.5 1.5 N/A N/A | |
| * Secondary fs: <end> <end> N/A N/A | |
| * User: <overlays entire FLASH except for "Monitor" section> | |
| */ | |
| static int __init | |
| katana_setup_mtd(void) | |
| { | |
| u32 size; | |
| int ptbl_entries; | |
| static struct mtd_partition *ptbl; | |
| size = katana_flash_size_0 + katana_flash_size_1; | |
| if (!size) | |
| return -ENOMEM; | |
| ptbl_entries = (size >= (64*MB)) ? 6 : 4; | |
| if ((ptbl = kcalloc(ptbl_entries, sizeof(struct mtd_partition), | |
| GFP_KERNEL)) == NULL) { | |
| printk(KERN_WARNING "Can't alloc MTD partition table\n"); | |
| return -ENOMEM; | |
| } | |
| ptbl[0].name = "Monitor"; | |
| ptbl[0].size = KATANA_MTD_MONITOR_SIZE; | |
| ptbl[1].name = "Primary Kernel"; | |
| ptbl[1].offset = MTDPART_OFS_NXTBLK; | |
| ptbl[1].size = 0x00180000; /* 1.5 MB */ | |
| ptbl[2].name = "Primary Filesystem"; | |
| ptbl[2].offset = MTDPART_OFS_APPEND; | |
| ptbl[2].size = MTDPART_SIZ_FULL; /* Correct for 16 & 32 MB */ | |
| ptbl[ptbl_entries-1].name = "User FLASH"; | |
| ptbl[ptbl_entries-1].offset = KATANA_MTD_MONITOR_SIZE; | |
| ptbl[ptbl_entries-1].size = MTDPART_SIZ_FULL; | |
| if (size >= (64*MB)) { | |
| ptbl[2].size = 30*MB; | |
| ptbl[3].name = "Secondary Kernel"; | |
| ptbl[3].offset = MTDPART_OFS_NXTBLK; | |
| ptbl[3].size = 0x00180000; /* 1.5 MB */ | |
| ptbl[4].name = "Secondary Filesystem"; | |
| ptbl[4].offset = MTDPART_OFS_APPEND; | |
| ptbl[4].size = MTDPART_SIZ_FULL; | |
| } | |
| physmap_map.size = size; | |
| physmap_set_partitions(ptbl, ptbl_entries); | |
| return 0; | |
| } | |
| arch_initcall(katana_setup_mtd); | |
| #endif | |
| static void | |
| katana_restart(char *cmd) | |
| { | |
| ulong i = 10000000; | |
| /* issue hard reset to the reset command register */ | |
| out_8(cpld_base + KATANA_CPLD_RST_CMD, KATANA_CPLD_RST_CMD_HR); | |
| while (i-- > 0) ; | |
| panic("restart failed\n"); | |
| } | |
| static void | |
| katana_halt(void) | |
| { | |
| u8 v; | |
| /* Turn on blue LED to indicate its okay to remove */ | |
| if (katana_id == KATANA_ID_750I) { | |
| u32 v; | |
| u8 save_exclude; | |
| /* Set LOO bit in cPCI HotSwap reg of hose 0 to turn on LED. */ | |
| save_exclude = mv64x60_pci_exclude_bridge; | |
| mv64x60_pci_exclude_bridge = 0; | |
| early_read_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0), | |
| MV64360_PCICFG_CPCI_HOTSWAP, &v); | |
| v &= 0xff; | |
| v |= (1 << 19); | |
| early_write_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0), | |
| MV64360_PCICFG_CPCI_HOTSWAP, v); | |
| mv64x60_pci_exclude_bridge = save_exclude; | |
| } else if (katana_id == KATANA_ID_752I) { | |
| v = in_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF); | |
| v |= HSL_PLD_HOT_SWAP_LED_BIT; | |
| out_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF, v); | |
| } | |
| while (1) ; | |
| /* NOTREACHED */ | |
| } | |
| static void | |
| katana_power_off(void) | |
| { | |
| katana_halt(); | |
| /* NOTREACHED */ | |
| } | |
| static int | |
| katana_show_cpuinfo(struct seq_file *m) | |
| { | |
| char *s; | |
| seq_printf(m, "cpu freq\t: %dMHz\n", | |
| (katana_get_cpu_freq() + 500000) / 1000000); | |
| seq_printf(m, "bus freq\t: %ldMHz\n", | |
| ((long)katana_bus_frequency + 500000) / 1000000); | |
| seq_printf(m, "vendor\t\t: Artesyn Communication Products, LLC\n"); | |
| seq_printf(m, "board\t\t: "); | |
| switch (katana_id) { | |
| case KATANA_ID_3750: | |
| seq_printf(m, "Katana 3750"); | |
| break; | |
| case KATANA_ID_750I: | |
| seq_printf(m, "Katana 750i"); | |
| break; | |
| case KATANA_ID_752I: | |
| seq_printf(m, "Katana 752i"); | |
| break; | |
| default: | |
| seq_printf(m, "Unknown"); | |
| break; | |
| } | |
| seq_printf(m, " (product id: 0x%x)\n", | |
| in_8(cpld_base + KATANA_CPLD_PRODUCT_ID)); | |
| seq_printf(m, "pci mode\t: %sMonarch\n", | |
| katana_is_monarch()? "" : "Non-"); | |
| seq_printf(m, "hardware rev\t: 0x%x\n", | |
| in_8(cpld_base+KATANA_CPLD_HARDWARE_VER)); | |
| seq_printf(m, "pld rev\t\t: 0x%x\n", | |
| in_8(cpld_base + KATANA_CPLD_PLD_VER)); | |
| switch(bh.type) { | |
| case MV64x60_TYPE_GT64260A: | |
| s = "gt64260a"; | |
| break; | |
| case MV64x60_TYPE_GT64260B: | |
| s = "gt64260b"; | |
| break; | |
| case MV64x60_TYPE_MV64360: | |
| s = "mv64360"; | |
| break; | |
| case MV64x60_TYPE_MV64460: | |
| s = "mv64460"; | |
| break; | |
| default: | |
| s = "Unknown"; | |
| } | |
| seq_printf(m, "bridge type\t: %s\n", s); | |
| seq_printf(m, "bridge rev\t: 0x%x\n", bh.rev); | |
| #if defined(CONFIG_NOT_COHERENT_CACHE) | |
| seq_printf(m, "coherency\t: %s\n", "off"); | |
| #else | |
| seq_printf(m, "coherency\t: %s\n", "on"); | |
| #endif | |
| return 0; | |
| } | |
| static void __init | |
| katana_calibrate_decr(void) | |
| { | |
| u32 freq; | |
| freq = katana_bus_frequency / 4; | |
| printk(KERN_INFO "time_init: decrementer frequency = %lu.%.6lu MHz\n", | |
| (long)freq / 1000000, (long)freq % 1000000); | |
| tb_ticks_per_jiffy = freq / HZ; | |
| tb_to_us = mulhwu_scale_factor(freq, 1000000); | |
| } | |
| /* | |
| * The katana supports both uImage and zImage. If uImage, get the mem size | |
| * from the bd info. If zImage, the bootwrapper adds a BI_MEMSIZE entry in | |
| * the bi_rec data which is sucked out and put into boot_mem_size by | |
| * parse_bootinfo(). MMU_init() will then use the boot_mem_size for the mem | |
| * size and not call this routine. The only way this will fail is when a uImage | |
| * is used but the fw doesn't pass in a valid bi_memsize. This should never | |
| * happen, though. | |
| */ | |
| unsigned long __init | |
| katana_find_end_of_memory(void) | |
| { | |
| bd_t *bdp = (bd_t *)__res; | |
| return bdp->bi_memsize; | |
| } | |
| #if defined(CONFIG_I2C_MV64XXX) && defined(CONFIG_SENSORS_M41T00) | |
| extern ulong m41t00_get_rtc_time(void); | |
| extern int m41t00_set_rtc_time(ulong); | |
| static int __init | |
| katana_rtc_hookup(void) | |
| { | |
| struct timespec tv; | |
| ppc_md.get_rtc_time = m41t00_get_rtc_time; | |
| ppc_md.set_rtc_time = m41t00_set_rtc_time; | |
| tv.tv_nsec = 0; | |
| tv.tv_sec = (ppc_md.get_rtc_time)(); | |
| do_settimeofday(&tv); | |
| return 0; | |
| } | |
| late_initcall(katana_rtc_hookup); | |
| #endif | |
| #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE) | |
| static void __init | |
| katana_map_io(void) | |
| { | |
| io_block_mapping(0xf8100000, 0xf8100000, 0x00020000, _PAGE_IO); | |
| } | |
| #endif | |
| void __init | |
| platform_init(unsigned long r3, unsigned long r4, unsigned long r5, | |
| unsigned long r6, unsigned long r7) | |
| { | |
| parse_bootinfo(find_bootinfo()); | |
| /* ASSUMPTION: If both r3 (bd_t pointer) and r6 (cmdline pointer) | |
| * are non-zero, then we should use the board info from the bd_t | |
| * structure and the cmdline pointed to by r6 instead of the | |
| * information from birecs, if any. Otherwise, use the information | |
| * from birecs as discovered by the preceeding call to | |
| * parse_bootinfo(). This rule should work with both PPCBoot, which | |
| * uses a bd_t board info structure, and the kernel boot wrapper, | |
| * which uses birecs. | |
| */ | |
| if (r3 && r6) { | |
| /* copy board info structure */ | |
| memcpy((void *)__res, (void *)(r3+KERNELBASE), sizeof(bd_t)); | |
| /* copy command line */ | |
| *(char *)(r7+KERNELBASE) = 0; | |
| strcpy(cmd_line, (char *)(r6+KERNELBASE)); | |
| } | |
| #ifdef CONFIG_BLK_DEV_INITRD | |
| /* take care of initrd if we have one */ | |
| if (r4) { | |
| initrd_start = r4 + KERNELBASE; | |
| initrd_end = r5 + KERNELBASE; | |
| } | |
| #endif /* CONFIG_BLK_DEV_INITRD */ | |
| isa_mem_base = 0; | |
| ppc_md.setup_arch = katana_setup_arch; | |
| ppc_md.pcibios_fixup_resources = katana_fixup_resources; | |
| ppc_md.show_cpuinfo = katana_show_cpuinfo; | |
| ppc_md.init_IRQ = mv64360_init_irq; | |
| ppc_md.get_irq = mv64360_get_irq; | |
| ppc_md.restart = katana_restart; | |
| ppc_md.power_off = katana_power_off; | |
| ppc_md.halt = katana_halt; | |
| ppc_md.find_end_of_memory = katana_find_end_of_memory; | |
| ppc_md.calibrate_decr = katana_calibrate_decr; | |
| #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE) | |
| ppc_md.setup_io_mappings = katana_map_io; | |
| ppc_md.progress = mv64x60_mpsc_progress; | |
| mv64x60_progress_init(CONFIG_MV64X60_NEW_BASE); | |
| #endif | |
| #if defined(CONFIG_SERIAL_MPSC) || defined(CONFIG_MV643XX_ETH) | |
| platform_notify = katana_platform_notify; | |
| #endif | |
| } |