| /* | |
| * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers. | |
| * | |
| * This driver is heavily based upon: | |
| * | |
| * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 | |
| * | |
| * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> | |
| * Portions Copyright (C) 2001 Sun Microsystems, Inc. | |
| * Portions Copyright (C) 2003 Red Hat Inc | |
| * | |
| * TODO | |
| * PLL mode | |
| * Look into engine reset on timeout errors. Should not be | |
| * required. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/pci.h> | |
| #include <linux/init.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/delay.h> | |
| #include <scsi/scsi_host.h> | |
| #include <linux/libata.h> | |
| #define DRV_NAME "pata_hpt37x" | |
| #define DRV_VERSION "0.5.1" | |
| struct hpt_clock { | |
| u8 xfer_speed; | |
| u32 timing; | |
| }; | |
| struct hpt_chip { | |
| const char *name; | |
| unsigned int base; | |
| struct hpt_clock const *clocks[4]; | |
| }; | |
| /* key for bus clock timings | |
| * bit | |
| * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW | |
| * DMA. cycles = value + 1 | |
| * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW | |
| * DMA. cycles = value + 1 | |
| * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file | |
| * register access. | |
| * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file | |
| * register access. | |
| * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. | |
| * during task file register access. | |
| * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA | |
| * xfer. | |
| * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task | |
| * register access. | |
| * 28 UDMA enable | |
| * 29 DMA enable | |
| * 30 PIO_MST enable. if set, the chip is in bus master mode during | |
| * PIO. | |
| * 31 FIFO enable. | |
| */ | |
| /* from highpoint documentation. these are old values */ | |
| static const struct hpt_clock hpt370_timings_33[] = { | |
| /* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ | |
| { XFER_UDMA_5, 0x16454e31 }, | |
| { XFER_UDMA_4, 0x16454e31 }, | |
| { XFER_UDMA_3, 0x166d4e31 }, | |
| { XFER_UDMA_2, 0x16494e31 }, | |
| { XFER_UDMA_1, 0x164d4e31 }, | |
| { XFER_UDMA_0, 0x16514e31 }, | |
| { XFER_MW_DMA_2, 0x26514e21 }, | |
| { XFER_MW_DMA_1, 0x26514e33 }, | |
| { XFER_MW_DMA_0, 0x26514e97 }, | |
| { XFER_PIO_4, 0x06514e21 }, | |
| { XFER_PIO_3, 0x06514e22 }, | |
| { XFER_PIO_2, 0x06514e33 }, | |
| { XFER_PIO_1, 0x06914e43 }, | |
| { XFER_PIO_0, 0x06914e57 }, | |
| { 0, 0x06514e57 } | |
| }; | |
| static const struct hpt_clock hpt370_timings_66[] = { | |
| { XFER_UDMA_5, 0x14846231 }, | |
| { XFER_UDMA_4, 0x14886231 }, | |
| { XFER_UDMA_3, 0x148c6231 }, | |
| { XFER_UDMA_2, 0x148c6231 }, | |
| { XFER_UDMA_1, 0x14906231 }, | |
| { XFER_UDMA_0, 0x14986231 }, | |
| { XFER_MW_DMA_2, 0x26514e21 }, | |
| { XFER_MW_DMA_1, 0x26514e33 }, | |
| { XFER_MW_DMA_0, 0x26514e97 }, | |
| { XFER_PIO_4, 0x06514e21 }, | |
| { XFER_PIO_3, 0x06514e22 }, | |
| { XFER_PIO_2, 0x06514e33 }, | |
| { XFER_PIO_1, 0x06914e43 }, | |
| { XFER_PIO_0, 0x06914e57 }, | |
| { 0, 0x06514e57 } | |
| }; | |
| /* these are the current (4 sep 2001) timings from highpoint */ | |
| static const struct hpt_clock hpt370a_timings_33[] = { | |
| { XFER_UDMA_5, 0x12446231 }, | |
| { XFER_UDMA_4, 0x12446231 }, | |
| { XFER_UDMA_3, 0x126c6231 }, | |
| { XFER_UDMA_2, 0x12486231 }, | |
| { XFER_UDMA_1, 0x124c6233 }, | |
| { XFER_UDMA_0, 0x12506297 }, | |
| { XFER_MW_DMA_2, 0x22406c31 }, | |
| { XFER_MW_DMA_1, 0x22406c33 }, | |
| { XFER_MW_DMA_0, 0x22406c97 }, | |
| { XFER_PIO_4, 0x06414e31 }, | |
| { XFER_PIO_3, 0x06414e42 }, | |
| { XFER_PIO_2, 0x06414e53 }, | |
| { XFER_PIO_1, 0x06814e93 }, | |
| { XFER_PIO_0, 0x06814ea7 }, | |
| { 0, 0x06814ea7 } | |
| }; | |
| /* 2x 33MHz timings */ | |
| static const struct hpt_clock hpt370a_timings_66[] = { | |
| { XFER_UDMA_5, 0x1488e673 }, | |
| { XFER_UDMA_4, 0x1488e673 }, | |
| { XFER_UDMA_3, 0x1498e673 }, | |
| { XFER_UDMA_2, 0x1490e673 }, | |
| { XFER_UDMA_1, 0x1498e677 }, | |
| { XFER_UDMA_0, 0x14a0e73f }, | |
| { XFER_MW_DMA_2, 0x2480fa73 }, | |
| { XFER_MW_DMA_1, 0x2480fa77 }, | |
| { XFER_MW_DMA_0, 0x2480fb3f }, | |
| { XFER_PIO_4, 0x0c82be73 }, | |
| { XFER_PIO_3, 0x0c82be95 }, | |
| { XFER_PIO_2, 0x0c82beb7 }, | |
| { XFER_PIO_1, 0x0d02bf37 }, | |
| { XFER_PIO_0, 0x0d02bf5f }, | |
| { 0, 0x0d02bf5f } | |
| }; | |
| static const struct hpt_clock hpt370a_timings_50[] = { | |
| { XFER_UDMA_5, 0x12848242 }, | |
| { XFER_UDMA_4, 0x12ac8242 }, | |
| { XFER_UDMA_3, 0x128c8242 }, | |
| { XFER_UDMA_2, 0x120c8242 }, | |
| { XFER_UDMA_1, 0x12148254 }, | |
| { XFER_UDMA_0, 0x121882ea }, | |
| { XFER_MW_DMA_2, 0x22808242 }, | |
| { XFER_MW_DMA_1, 0x22808254 }, | |
| { XFER_MW_DMA_0, 0x228082ea }, | |
| { XFER_PIO_4, 0x0a81f442 }, | |
| { XFER_PIO_3, 0x0a81f443 }, | |
| { XFER_PIO_2, 0x0a81f454 }, | |
| { XFER_PIO_1, 0x0ac1f465 }, | |
| { XFER_PIO_0, 0x0ac1f48a }, | |
| { 0, 0x0ac1f48a } | |
| }; | |
| static const struct hpt_clock hpt372_timings_33[] = { | |
| { XFER_UDMA_6, 0x1c81dc62 }, | |
| { XFER_UDMA_5, 0x1c6ddc62 }, | |
| { XFER_UDMA_4, 0x1c8ddc62 }, | |
| { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */ | |
| { XFER_UDMA_2, 0x1c91dc62 }, | |
| { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */ | |
| { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */ | |
| { XFER_MW_DMA_2, 0x2c829262 }, | |
| { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */ | |
| { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */ | |
| { XFER_PIO_4, 0x0c829c62 }, | |
| { XFER_PIO_3, 0x0c829c84 }, | |
| { XFER_PIO_2, 0x0c829ca6 }, | |
| { XFER_PIO_1, 0x0d029d26 }, | |
| { XFER_PIO_0, 0x0d029d5e }, | |
| { 0, 0x0d029d5e } | |
| }; | |
| static const struct hpt_clock hpt372_timings_50[] = { | |
| { XFER_UDMA_5, 0x12848242 }, | |
| { XFER_UDMA_4, 0x12ac8242 }, | |
| { XFER_UDMA_3, 0x128c8242 }, | |
| { XFER_UDMA_2, 0x120c8242 }, | |
| { XFER_UDMA_1, 0x12148254 }, | |
| { XFER_UDMA_0, 0x121882ea }, | |
| { XFER_MW_DMA_2, 0x22808242 }, | |
| { XFER_MW_DMA_1, 0x22808254 }, | |
| { XFER_MW_DMA_0, 0x228082ea }, | |
| { XFER_PIO_4, 0x0a81f442 }, | |
| { XFER_PIO_3, 0x0a81f443 }, | |
| { XFER_PIO_2, 0x0a81f454 }, | |
| { XFER_PIO_1, 0x0ac1f465 }, | |
| { XFER_PIO_0, 0x0ac1f48a }, | |
| { 0, 0x0a81f443 } | |
| }; | |
| static const struct hpt_clock hpt372_timings_66[] = { | |
| { XFER_UDMA_6, 0x1c869c62 }, | |
| { XFER_UDMA_5, 0x1cae9c62 }, | |
| { XFER_UDMA_4, 0x1c8a9c62 }, | |
| { XFER_UDMA_3, 0x1c8e9c62 }, | |
| { XFER_UDMA_2, 0x1c929c62 }, | |
| { XFER_UDMA_1, 0x1c9a9c62 }, | |
| { XFER_UDMA_0, 0x1c829c62 }, | |
| { XFER_MW_DMA_2, 0x2c829c62 }, | |
| { XFER_MW_DMA_1, 0x2c829c66 }, | |
| { XFER_MW_DMA_0, 0x2c829d2e }, | |
| { XFER_PIO_4, 0x0c829c62 }, | |
| { XFER_PIO_3, 0x0c829c84 }, | |
| { XFER_PIO_2, 0x0c829ca6 }, | |
| { XFER_PIO_1, 0x0d029d26 }, | |
| { XFER_PIO_0, 0x0d029d5e }, | |
| { 0, 0x0d029d26 } | |
| }; | |
| static const struct hpt_clock hpt374_timings_33[] = { | |
| { XFER_UDMA_6, 0x12808242 }, | |
| { XFER_UDMA_5, 0x12848242 }, | |
| { XFER_UDMA_4, 0x12ac8242 }, | |
| { XFER_UDMA_3, 0x128c8242 }, | |
| { XFER_UDMA_2, 0x120c8242 }, | |
| { XFER_UDMA_1, 0x12148254 }, | |
| { XFER_UDMA_0, 0x121882ea }, | |
| { XFER_MW_DMA_2, 0x22808242 }, | |
| { XFER_MW_DMA_1, 0x22808254 }, | |
| { XFER_MW_DMA_0, 0x228082ea }, | |
| { XFER_PIO_4, 0x0a81f442 }, | |
| { XFER_PIO_3, 0x0a81f443 }, | |
| { XFER_PIO_2, 0x0a81f454 }, | |
| { XFER_PIO_1, 0x0ac1f465 }, | |
| { XFER_PIO_0, 0x0ac1f48a }, | |
| { 0, 0x06814e93 } | |
| }; | |
| static const struct hpt_chip hpt370 = { | |
| "HPT370", | |
| 48, | |
| { | |
| hpt370_timings_33, | |
| NULL, | |
| NULL, | |
| hpt370_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt370a = { | |
| "HPT370A", | |
| 48, | |
| { | |
| hpt370a_timings_33, | |
| NULL, | |
| hpt370a_timings_50, | |
| hpt370a_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt372 = { | |
| "HPT372", | |
| 55, | |
| { | |
| hpt372_timings_33, | |
| NULL, | |
| hpt372_timings_50, | |
| hpt372_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt302 = { | |
| "HPT302", | |
| 66, | |
| { | |
| hpt372_timings_33, | |
| NULL, | |
| hpt372_timings_50, | |
| hpt372_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt371 = { | |
| "HPT371", | |
| 66, | |
| { | |
| hpt372_timings_33, | |
| NULL, | |
| hpt372_timings_50, | |
| hpt372_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt372a = { | |
| "HPT372A", | |
| 66, | |
| { | |
| hpt372_timings_33, | |
| NULL, | |
| hpt372_timings_50, | |
| hpt372_timings_66 | |
| } | |
| }; | |
| static const struct hpt_chip hpt374 = { | |
| "HPT374", | |
| 48, | |
| { | |
| hpt374_timings_33, | |
| NULL, | |
| NULL, | |
| NULL | |
| } | |
| }; | |
| /** | |
| * hpt37x_find_mode - reset the hpt37x bus | |
| * @ap: ATA port | |
| * @speed: transfer mode | |
| * | |
| * Return the 32bit register programming information for this channel | |
| * that matches the speed provided. | |
| */ | |
| static u32 hpt37x_find_mode(struct ata_port *ap, int speed) | |
| { | |
| struct hpt_clock *clocks = ap->host->private_data; | |
| while(clocks->xfer_speed) { | |
| if (clocks->xfer_speed == speed) | |
| return clocks->timing; | |
| clocks++; | |
| } | |
| BUG(); | |
| return 0xffffffffU; /* silence compiler warning */ | |
| } | |
| static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[]) | |
| { | |
| unsigned char model_num[40]; | |
| char *s; | |
| unsigned int len; | |
| int i = 0; | |
| ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, | |
| sizeof(model_num)); | |
| s = &model_num[0]; | |
| len = strnlen(s, sizeof(model_num)); | |
| /* ATAPI specifies that empty space is blank-filled; remove blanks */ | |
| while ((len > 0) && (s[len - 1] == ' ')) { | |
| len--; | |
| s[len] = 0; | |
| } | |
| while(list[i] != NULL) { | |
| if (!strncmp(list[i], s, len)) { | |
| printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n", | |
| modestr, list[i]); | |
| return 1; | |
| } | |
| i++; | |
| } | |
| return 0; | |
| } | |
| static const char *bad_ata33[] = { | |
| "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", | |
| "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", | |
| "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", | |
| "Maxtor 90510D4", | |
| "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", | |
| "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", | |
| "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", | |
| NULL | |
| }; | |
| static const char *bad_ata100_5[] = { | |
| "IBM-DTLA-307075", | |
| "IBM-DTLA-307060", | |
| "IBM-DTLA-307045", | |
| "IBM-DTLA-307030", | |
| "IBM-DTLA-307020", | |
| "IBM-DTLA-307015", | |
| "IBM-DTLA-305040", | |
| "IBM-DTLA-305030", | |
| "IBM-DTLA-305020", | |
| "IC35L010AVER07-0", | |
| "IC35L020AVER07-0", | |
| "IC35L030AVER07-0", | |
| "IC35L040AVER07-0", | |
| "IC35L060AVER07-0", | |
| "WDC AC310200R", | |
| NULL | |
| }; | |
| /** | |
| * hpt370_filter - mode selection filter | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Block UDMA on devices that cause trouble with this controller. | |
| */ | |
| static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) | |
| { | |
| if (adev->class != ATA_DEV_ATA) { | |
| if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) | |
| mask &= ~ATA_MASK_UDMA; | |
| if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) | |
| mask &= ~(0x1F << ATA_SHIFT_UDMA); | |
| } | |
| return ata_pci_default_filter(ap, adev, mask); | |
| } | |
| /** | |
| * hpt370a_filter - mode selection filter | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Block UDMA on devices that cause trouble with this controller. | |
| */ | |
| static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) | |
| { | |
| if (adev->class != ATA_DEV_ATA) { | |
| if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) | |
| mask &= ~ (0x1F << ATA_SHIFT_UDMA); | |
| } | |
| return ata_pci_default_filter(ap, adev, mask); | |
| } | |
| /** | |
| * hpt37x_pre_reset - reset the hpt37x bus | |
| * @ap: ATA port to reset | |
| * | |
| * Perform the initial reset handling for the 370/372 and 374 func 0 | |
| */ | |
| static int hpt37x_pre_reset(struct ata_port *ap) | |
| { | |
| u8 scr2, ata66; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| static const struct pci_bits hpt37x_enable_bits[] = { | |
| { 0x50, 1, 0x04, 0x04 }, | |
| { 0x54, 1, 0x04, 0x04 } | |
| }; | |
| if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) | |
| return -ENOENT; | |
| pci_read_config_byte(pdev, 0x5B, &scr2); | |
| pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); | |
| /* Cable register now active */ | |
| pci_read_config_byte(pdev, 0x5A, &ata66); | |
| /* Restore state */ | |
| pci_write_config_byte(pdev, 0x5B, scr2); | |
| if (ata66 & (1 << ap->port_no)) | |
| ap->cbl = ATA_CBL_PATA40; | |
| else | |
| ap->cbl = ATA_CBL_PATA80; | |
| /* Reset the state machine */ | |
| pci_write_config_byte(pdev, 0x50, 0x37); | |
| pci_write_config_byte(pdev, 0x54, 0x37); | |
| udelay(100); | |
| return ata_std_prereset(ap); | |
| } | |
| /** | |
| * hpt37x_error_handler - reset the hpt374 | |
| * @ap: ATA port to reset | |
| * | |
| * Perform probe for HPT37x, except for HPT374 channel 2 | |
| */ | |
| static void hpt37x_error_handler(struct ata_port *ap) | |
| { | |
| ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); | |
| } | |
| static int hpt374_pre_reset(struct ata_port *ap) | |
| { | |
| static const struct pci_bits hpt37x_enable_bits[] = { | |
| { 0x50, 1, 0x04, 0x04 }, | |
| { 0x54, 1, 0x04, 0x04 } | |
| }; | |
| u16 mcr3, mcr6; | |
| u8 ata66; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no])) | |
| return -ENOENT; | |
| /* Do the extra channel work */ | |
| pci_read_config_word(pdev, 0x52, &mcr3); | |
| pci_read_config_word(pdev, 0x56, &mcr6); | |
| /* Set bit 15 of 0x52 to enable TCBLID as input | |
| Set bit 15 of 0x56 to enable FCBLID as input | |
| */ | |
| pci_write_config_word(pdev, 0x52, mcr3 | 0x8000); | |
| pci_write_config_word(pdev, 0x56, mcr6 | 0x8000); | |
| pci_read_config_byte(pdev, 0x5A, &ata66); | |
| /* Reset TCBLID/FCBLID to output */ | |
| pci_write_config_word(pdev, 0x52, mcr3); | |
| pci_write_config_word(pdev, 0x56, mcr6); | |
| if (ata66 & (1 << ap->port_no)) | |
| ap->cbl = ATA_CBL_PATA40; | |
| else | |
| ap->cbl = ATA_CBL_PATA80; | |
| /* Reset the state machine */ | |
| pci_write_config_byte(pdev, 0x50, 0x37); | |
| pci_write_config_byte(pdev, 0x54, 0x37); | |
| udelay(100); | |
| return ata_std_prereset(ap); | |
| } | |
| /** | |
| * hpt374_error_handler - reset the hpt374 | |
| * @classes: | |
| * | |
| * The 374 cable detect is a little different due to the extra | |
| * channels. The function 0 channels work like usual but function 1 | |
| * is special | |
| */ | |
| static void hpt374_error_handler(struct ata_port *ap) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| if (!(PCI_FUNC(pdev->devfn) & 1)) | |
| hpt37x_error_handler(ap); | |
| else | |
| ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset); | |
| } | |
| /** | |
| * hpt370_set_piomode - PIO setup | |
| * @ap: ATA interface | |
| * @adev: device on the interface | |
| * | |
| * Perform PIO mode setup. | |
| */ | |
| static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 addr1, addr2; | |
| u32 reg; | |
| u32 mode; | |
| u8 fast; | |
| addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); | |
| addr2 = 0x51 + 4 * ap->port_no; | |
| /* Fast interrupt prediction disable, hold off interrupt disable */ | |
| pci_read_config_byte(pdev, addr2, &fast); | |
| fast &= ~0x02; | |
| fast |= 0x01; | |
| pci_write_config_byte(pdev, addr2, fast); | |
| pci_read_config_dword(pdev, addr1, ®); | |
| mode = hpt37x_find_mode(ap, adev->pio_mode); | |
| mode &= ~0x8000000; /* No FIFO in PIO */ | |
| mode &= ~0x30070000; /* Leave config bits alone */ | |
| reg &= 0x30070000; /* Strip timing bits */ | |
| pci_write_config_dword(pdev, addr1, reg | mode); | |
| } | |
| /** | |
| * hpt370_set_dmamode - DMA timing setup | |
| * @ap: ATA interface | |
| * @adev: Device being configured | |
| * | |
| * Set up the channel for MWDMA or UDMA modes. Much the same as with | |
| * PIO, load the mode number and then set MWDMA or UDMA flag. | |
| */ | |
| static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 addr1, addr2; | |
| u32 reg; | |
| u32 mode; | |
| u8 fast; | |
| addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); | |
| addr2 = 0x51 + 4 * ap->port_no; | |
| /* Fast interrupt prediction disable, hold off interrupt disable */ | |
| pci_read_config_byte(pdev, addr2, &fast); | |
| fast &= ~0x02; | |
| fast |= 0x01; | |
| pci_write_config_byte(pdev, addr2, fast); | |
| pci_read_config_dword(pdev, addr1, ®); | |
| mode = hpt37x_find_mode(ap, adev->dma_mode); | |
| mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ | |
| mode &= ~0xC0000000; /* Leave config bits alone */ | |
| reg &= 0xC0000000; /* Strip timing bits */ | |
| pci_write_config_dword(pdev, addr1, reg | mode); | |
| } | |
| /** | |
| * hpt370_bmdma_start - DMA engine begin | |
| * @qc: ATA command | |
| * | |
| * The 370 and 370A want us to reset the DMA engine each time we | |
| * use it. The 372 and later are fine. | |
| */ | |
| static void hpt370_bmdma_start(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); | |
| udelay(10); | |
| ata_bmdma_start(qc); | |
| } | |
| /** | |
| * hpt370_bmdma_end - DMA engine stop | |
| * @qc: ATA command | |
| * | |
| * Work around the HPT370 DMA engine. | |
| */ | |
| static void hpt370_bmdma_stop(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2); | |
| u8 dma_cmd; | |
| unsigned long bmdma = ap->ioaddr.bmdma_addr; | |
| if (dma_stat & 0x01) { | |
| udelay(20); | |
| dma_stat = inb(bmdma + 2); | |
| } | |
| if (dma_stat & 0x01) { | |
| /* Clear the engine */ | |
| pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); | |
| udelay(10); | |
| /* Stop DMA */ | |
| dma_cmd = inb(bmdma ); | |
| outb(dma_cmd & 0xFE, bmdma); | |
| /* Clear Error */ | |
| dma_stat = inb(bmdma + 2); | |
| outb(dma_stat | 0x06 , bmdma + 2); | |
| /* Clear the engine */ | |
| pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); | |
| udelay(10); | |
| } | |
| ata_bmdma_stop(qc); | |
| } | |
| /** | |
| * hpt372_set_piomode - PIO setup | |
| * @ap: ATA interface | |
| * @adev: device on the interface | |
| * | |
| * Perform PIO mode setup. | |
| */ | |
| static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 addr1, addr2; | |
| u32 reg; | |
| u32 mode; | |
| u8 fast; | |
| addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); | |
| addr2 = 0x51 + 4 * ap->port_no; | |
| /* Fast interrupt prediction disable, hold off interrupt disable */ | |
| pci_read_config_byte(pdev, addr2, &fast); | |
| fast &= ~0x07; | |
| pci_write_config_byte(pdev, addr2, fast); | |
| pci_read_config_dword(pdev, addr1, ®); | |
| mode = hpt37x_find_mode(ap, adev->pio_mode); | |
| printk("Find mode for %d reports %X\n", adev->pio_mode, mode); | |
| mode &= ~0x80000000; /* No FIFO in PIO */ | |
| mode &= ~0x30070000; /* Leave config bits alone */ | |
| reg &= 0x30070000; /* Strip timing bits */ | |
| pci_write_config_dword(pdev, addr1, reg | mode); | |
| } | |
| /** | |
| * hpt372_set_dmamode - DMA timing setup | |
| * @ap: ATA interface | |
| * @adev: Device being configured | |
| * | |
| * Set up the channel for MWDMA or UDMA modes. Much the same as with | |
| * PIO, load the mode number and then set MWDMA or UDMA flag. | |
| */ | |
| static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 addr1, addr2; | |
| u32 reg; | |
| u32 mode; | |
| u8 fast; | |
| addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); | |
| addr2 = 0x51 + 4 * ap->port_no; | |
| /* Fast interrupt prediction disable, hold off interrupt disable */ | |
| pci_read_config_byte(pdev, addr2, &fast); | |
| fast &= ~0x07; | |
| pci_write_config_byte(pdev, addr2, fast); | |
| pci_read_config_dword(pdev, addr1, ®); | |
| mode = hpt37x_find_mode(ap, adev->dma_mode); | |
| printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode); | |
| mode &= ~0xC0000000; /* Leave config bits alone */ | |
| mode |= 0x80000000; /* FIFO in MWDMA or UDMA */ | |
| reg &= 0xC0000000; /* Strip timing bits */ | |
| pci_write_config_dword(pdev, addr1, reg | mode); | |
| } | |
| /** | |
| * hpt37x_bmdma_end - DMA engine stop | |
| * @qc: ATA command | |
| * | |
| * Clean up after the HPT372 and later DMA engine | |
| */ | |
| static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| int mscreg = 0x50 + 2 * ap->port_no; | |
| u8 bwsr_stat, msc_stat; | |
| pci_read_config_byte(pdev, 0x6A, &bwsr_stat); | |
| pci_read_config_byte(pdev, mscreg, &msc_stat); | |
| if (bwsr_stat & (1 << ap->port_no)) | |
| pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); | |
| ata_bmdma_stop(qc); | |
| } | |
| static struct scsi_host_template hpt37x_sht = { | |
| .module = THIS_MODULE, | |
| .name = DRV_NAME, | |
| .ioctl = ata_scsi_ioctl, | |
| .queuecommand = ata_scsi_queuecmd, | |
| .can_queue = ATA_DEF_QUEUE, | |
| .this_id = ATA_SHT_THIS_ID, | |
| .sg_tablesize = LIBATA_MAX_PRD, | |
| .max_sectors = ATA_MAX_SECTORS, | |
| .cmd_per_lun = ATA_SHT_CMD_PER_LUN, | |
| .emulated = ATA_SHT_EMULATED, | |
| .use_clustering = ATA_SHT_USE_CLUSTERING, | |
| .proc_name = DRV_NAME, | |
| .dma_boundary = ATA_DMA_BOUNDARY, | |
| .slave_configure = ata_scsi_slave_config, | |
| .bios_param = ata_std_bios_param, | |
| }; | |
| /* | |
| * Configuration for HPT370 | |
| */ | |
| static struct ata_port_operations hpt370_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = hpt370_set_piomode, | |
| .set_dmamode = hpt370_set_dmamode, | |
| .mode_filter = hpt370_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = hpt37x_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = hpt370_bmdma_start, | |
| .bmdma_stop = hpt370_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /* | |
| * Configuration for HPT370A. Close to 370 but less filters | |
| */ | |
| static struct ata_port_operations hpt370a_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = hpt370_set_piomode, | |
| .set_dmamode = hpt370_set_dmamode, | |
| .mode_filter = hpt370a_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = hpt37x_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = hpt370_bmdma_start, | |
| .bmdma_stop = hpt370_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /* | |
| * Configuration for HPT372, HPT371, HPT302. Slightly different PIO | |
| * and DMA mode setting functionality. | |
| */ | |
| static struct ata_port_operations hpt372_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = hpt372_set_piomode, | |
| .set_dmamode = hpt372_set_dmamode, | |
| .mode_filter = ata_pci_default_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = hpt37x_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = ata_bmdma_start, | |
| .bmdma_stop = hpt37x_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /* | |
| * Configuration for HPT374. Mode setting works like 372 and friends | |
| * but we have a different cable detection procedure. | |
| */ | |
| static struct ata_port_operations hpt374_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = hpt372_set_piomode, | |
| .set_dmamode = hpt372_set_dmamode, | |
| .mode_filter = ata_pci_default_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = hpt374_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = ata_bmdma_start, | |
| .bmdma_stop = hpt37x_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /** | |
| * htp37x_clock_slot - Turn timing to PC clock entry | |
| * @freq: Reported frequency timing | |
| * @base: Base timing | |
| * | |
| * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50 | |
| * and 3 for 66Mhz) | |
| */ | |
| static int hpt37x_clock_slot(unsigned int freq, unsigned int base) | |
| { | |
| unsigned int f = (base * freq) / 192; /* Mhz */ | |
| if (f < 40) | |
| return 0; /* 33Mhz slot */ | |
| if (f < 45) | |
| return 1; /* 40Mhz slot */ | |
| if (f < 55) | |
| return 2; /* 50Mhz slot */ | |
| return 3; /* 60Mhz slot */ | |
| } | |
| /** | |
| * hpt37x_calibrate_dpll - Calibrate the DPLL loop | |
| * @dev: PCI device | |
| * | |
| * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this | |
| * succeeds | |
| */ | |
| static int hpt37x_calibrate_dpll(struct pci_dev *dev) | |
| { | |
| u8 reg5b; | |
| u32 reg5c; | |
| int tries; | |
| for(tries = 0; tries < 0x5000; tries++) { | |
| udelay(50); | |
| pci_read_config_byte(dev, 0x5b, ®5b); | |
| if (reg5b & 0x80) { | |
| /* See if it stays set */ | |
| for(tries = 0; tries < 0x1000; tries ++) { | |
| pci_read_config_byte(dev, 0x5b, ®5b); | |
| /* Failed ? */ | |
| if ((reg5b & 0x80) == 0) | |
| return 0; | |
| } | |
| /* Turn off tuning, we have the DPLL set */ | |
| pci_read_config_dword(dev, 0x5c, ®5c); | |
| pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); | |
| return 1; | |
| } | |
| } | |
| /* Never went stable */ | |
| return 0; | |
| } | |
| /** | |
| * hpt37x_init_one - Initialise an HPT37X/302 | |
| * @dev: PCI device | |
| * @id: Entry in match table | |
| * | |
| * Initialise an HPT37x device. There are some interesting complications | |
| * here. Firstly the chip may report 366 and be one of several variants. | |
| * Secondly all the timings depend on the clock for the chip which we must | |
| * detect and look up | |
| * | |
| * This is the known chip mappings. It may be missing a couple of later | |
| * releases. | |
| * | |
| * Chip version PCI Rev Notes | |
| * HPT366 4 (HPT366) 0 Other driver | |
| * HPT366 4 (HPT366) 1 Other driver | |
| * HPT368 4 (HPT366) 2 Other driver | |
| * HPT370 4 (HPT366) 3 UDMA100 | |
| * HPT370A 4 (HPT366) 4 UDMA100 | |
| * HPT372 4 (HPT366) 5 UDMA133 (1) | |
| * HPT372N 4 (HPT366) 6 Other driver | |
| * HPT372A 5 (HPT372) 1 UDMA133 (1) | |
| * HPT372N 5 (HPT372) 2 Other driver | |
| * HPT302 6 (HPT302) 1 UDMA133 | |
| * HPT302N 6 (HPT302) 2 Other driver | |
| * HPT371 7 (HPT371) * UDMA133 | |
| * HPT374 8 (HPT374) * UDMA133 4 channel | |
| * HPT372N 9 (HPT372N) * Other driver | |
| * | |
| * (1) UDMA133 support depends on the bus clock | |
| */ | |
| static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| /* HPT370 - UDMA100 */ | |
| static struct ata_port_info info_hpt370 = { | |
| .sht = &hpt37x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x3f, | |
| .port_ops = &hpt370_port_ops | |
| }; | |
| /* HPT370A - UDMA100 */ | |
| static struct ata_port_info info_hpt370a = { | |
| .sht = &hpt37x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x3f, | |
| .port_ops = &hpt370a_port_ops | |
| }; | |
| /* HPT371, 372 and friends - UDMA133 */ | |
| static struct ata_port_info info_hpt372 = { | |
| .sht = &hpt37x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x7f, | |
| .port_ops = &hpt372_port_ops | |
| }; | |
| /* HPT371, 372 and friends - UDMA100 at 50MHz clock */ | |
| static struct ata_port_info info_hpt372_50 = { | |
| .sht = &hpt37x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x3f, | |
| .port_ops = &hpt372_port_ops | |
| }; | |
| /* HPT374 - UDMA133 */ | |
| static struct ata_port_info info_hpt374 = { | |
| .sht = &hpt37x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x7f, | |
| .port_ops = &hpt374_port_ops | |
| }; | |
| static const int MHz[4] = { 33, 40, 50, 66 }; | |
| struct ata_port_info *port_info[2]; | |
| struct ata_port_info *port; | |
| u8 irqmask; | |
| u32 class_rev; | |
| u32 freq; | |
| const struct hpt_chip *chip_table; | |
| int clock_slot; | |
| pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); | |
| class_rev &= 0xFF; | |
| if (dev->device == PCI_DEVICE_ID_TTI_HPT366) { | |
| /* May be a later chip in disguise. Check */ | |
| /* Older chips are in the HPT366 driver. Ignore them */ | |
| if (class_rev < 3) | |
| return -ENODEV; | |
| /* N series chips have their own driver. Ignore */ | |
| if (class_rev == 6) | |
| return -ENODEV; | |
| switch(class_rev) { | |
| case 3: | |
| port = &info_hpt370; | |
| chip_table = &hpt370; | |
| break; | |
| case 4: | |
| port = &info_hpt370a; | |
| chip_table = &hpt370a; | |
| break; | |
| case 5: | |
| port = &info_hpt372; | |
| chip_table = &hpt372; | |
| break; | |
| default: | |
| printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev); | |
| return -ENODEV; | |
| } | |
| } else { | |
| switch(dev->device) { | |
| case PCI_DEVICE_ID_TTI_HPT372: | |
| /* 372N if rev >= 2*/ | |
| if (class_rev >= 2) | |
| return -ENODEV; | |
| port = &info_hpt372; | |
| chip_table = &hpt372a; | |
| break; | |
| case PCI_DEVICE_ID_TTI_HPT302: | |
| /* 302N if rev > 1 */ | |
| if (class_rev > 1) | |
| return -ENODEV; | |
| port = &info_hpt372; | |
| /* Check this */ | |
| chip_table = &hpt302; | |
| break; | |
| case PCI_DEVICE_ID_TTI_HPT371: | |
| port = &info_hpt372; | |
| chip_table = &hpt371; | |
| break; | |
| case PCI_DEVICE_ID_TTI_HPT374: | |
| chip_table = &hpt374; | |
| port = &info_hpt374; | |
| break; | |
| default: | |
| printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device); | |
| return -ENODEV; | |
| } | |
| } | |
| /* Ok so this is a chip we support */ | |
| pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); | |
| pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); | |
| pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); | |
| pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); | |
| pci_read_config_byte(dev, 0x5A, &irqmask); | |
| irqmask &= ~0x10; | |
| pci_write_config_byte(dev, 0x5a, irqmask); | |
| /* | |
| * default to pci clock. make sure MA15/16 are set to output | |
| * to prevent drives having problems with 40-pin cables. Needed | |
| * for some drives such as IBM-DTLA which will not enter ready | |
| * state on reset when PDIAG is a input. | |
| */ | |
| pci_write_config_byte(dev, 0x5b, 0x23); | |
| pci_read_config_dword(dev, 0x70, &freq); | |
| if ((freq >> 12) != 0xABCDE) { | |
| int i; | |
| u8 sr; | |
| u32 total = 0; | |
| printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n"); | |
| /* This is the process the HPT371 BIOS is reported to use */ | |
| for(i = 0; i < 128; i++) { | |
| pci_read_config_byte(dev, 0x78, &sr); | |
| total += sr; | |
| udelay(15); | |
| } | |
| freq = total / 128; | |
| } | |
| freq &= 0x1FF; | |
| /* | |
| * Turn the frequency check into a band and then find a timing | |
| * table to match it. | |
| */ | |
| clock_slot = hpt37x_clock_slot(freq, chip_table->base); | |
| if (chip_table->clocks[clock_slot] == NULL) { | |
| /* | |
| * We need to try PLL mode instead | |
| */ | |
| unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192; | |
| unsigned int f_high = f_low + 2; | |
| int adjust; | |
| for(adjust = 0; adjust < 8; adjust++) { | |
| if (hpt37x_calibrate_dpll(dev)) | |
| break; | |
| /* See if it'll settle at a fractionally different clock */ | |
| if ((adjust & 3) == 3) { | |
| f_low --; | |
| f_high ++; | |
| } | |
| pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); | |
| } | |
| if (adjust == 8) { | |
| printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n"); | |
| return -ENODEV; | |
| } | |
| /* Check if this works for all cases */ | |
| port->private_data = (void *)hpt370_timings_66; | |
| printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]); | |
| } else { | |
| port->private_data = (void *)chip_table->clocks[clock_slot]; | |
| /* | |
| * Perform a final fixup. The 371 and 372 clock determines | |
| * if UDMA133 is available. | |
| */ | |
| if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */ | |
| printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n"); | |
| if (port == &info_hpt372) | |
| port = &info_hpt372_50; | |
| else BUG(); | |
| } | |
| printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]); | |
| } | |
| port_info[0] = port_info[1] = port; | |
| /* Now kick off ATA set up */ | |
| return ata_pci_init_one(dev, port_info, 2); | |
| } | |
| static const struct pci_device_id hpt37x[] = { | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), }, | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), }, | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), }, | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), }, | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), }, | |
| { }, | |
| }; | |
| static struct pci_driver hpt37x_pci_driver = { | |
| .name = DRV_NAME, | |
| .id_table = hpt37x, | |
| .probe = hpt37x_init_one, | |
| .remove = ata_pci_remove_one | |
| }; | |
| static int __init hpt37x_init(void) | |
| { | |
| return pci_register_driver(&hpt37x_pci_driver); | |
| } | |
| static void __exit hpt37x_exit(void) | |
| { | |
| pci_unregister_driver(&hpt37x_pci_driver); | |
| } | |
| MODULE_AUTHOR("Alan Cox"); | |
| MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DEVICE_TABLE(pci, hpt37x); | |
| MODULE_VERSION(DRV_VERSION); | |
| module_init(hpt37x_init); | |
| module_exit(hpt37x_exit); |