| /* | |
| * pata_hpt3x3 - HPT3x3 driver | |
| * (c) Copyright 2005-2006 Red Hat | |
| * | |
| * Was pata_hpt34x but the naming was confusing as it supported the | |
| * 343 and 363 so it has been renamed. | |
| * | |
| * Based on: | |
| * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002 | |
| * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> | |
| * | |
| * May be copied or modified under the terms of the GNU General Public | |
| * License | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/pci.h> | |
| #include <linux/init.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/delay.h> | |
| #include <scsi/scsi_host.h> | |
| #include <linux/libata.h> | |
| #define DRV_NAME "pata_hpt3x3" | |
| #define DRV_VERSION "0.4.1" | |
| static int hpt3x3_probe_init(struct ata_port *ap) | |
| { | |
| ap->cbl = ATA_CBL_PATA40; | |
| return ata_std_prereset(ap); | |
| } | |
| /** | |
| * hpt3x3_probe_reset - reset the hpt3x3 bus | |
| * @ap: ATA port to reset | |
| * | |
| * Perform the housekeeping when doing an ATA bus reeset. We just | |
| * need to force the cable type. | |
| */ | |
| static void hpt3x3_error_handler(struct ata_port *ap) | |
| { | |
| return ata_bmdma_drive_eh(ap, hpt3x3_probe_init, ata_std_softreset, NULL, ata_std_postreset); | |
| } | |
| /** | |
| * hpt3x3_set_piomode - PIO setup | |
| * @ap: ATA interface | |
| * @adev: device on the interface | |
| * | |
| * Set our PIO requirements. This is fairly simple on the HPT3x3 as | |
| * all we have to do is clear the MWDMA and UDMA bits then load the | |
| * mode number. | |
| */ | |
| static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 r1, r2; | |
| int dn = 2 * ap->port_no + adev->devno; | |
| pci_read_config_dword(pdev, 0x44, &r1); | |
| pci_read_config_dword(pdev, 0x48, &r2); | |
| /* Load the PIO timing number */ | |
| r1 &= ~(7 << (3 * dn)); | |
| r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn); | |
| r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ | |
| pci_write_config_dword(pdev, 0x44, r1); | |
| pci_write_config_dword(pdev, 0x48, r2); | |
| } | |
| /** | |
| * hpt3x3_set_dmamode - DMA timing setup | |
| * @ap: ATA interface | |
| * @adev: Device being configured | |
| * | |
| * Set up the channel for MWDMA or UDMA modes. Much the same as with | |
| * PIO, load the mode number and then set MWDMA or UDMA flag. | |
| */ | |
| static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u32 r1, r2; | |
| int dn = 2 * ap->port_no + adev->devno; | |
| int mode_num = adev->dma_mode & 0x0F; | |
| pci_read_config_dword(pdev, 0x44, &r1); | |
| pci_read_config_dword(pdev, 0x48, &r2); | |
| /* Load the timing number */ | |
| r1 &= ~(7 << (3 * dn)); | |
| r1 |= (mode_num << (3 * dn)); | |
| r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ | |
| if (adev->dma_mode >= XFER_UDMA_0) | |
| r2 |= 0x01 << dn; /* Ultra mode */ | |
| else | |
| r2 |= 0x10 << dn; /* MWDMA */ | |
| pci_write_config_dword(pdev, 0x44, r1); | |
| pci_write_config_dword(pdev, 0x48, r2); | |
| } | |
| static struct scsi_host_template hpt3x3_sht = { | |
| .module = THIS_MODULE, | |
| .name = DRV_NAME, | |
| .ioctl = ata_scsi_ioctl, | |
| .queuecommand = ata_scsi_queuecmd, | |
| .can_queue = ATA_DEF_QUEUE, | |
| .this_id = ATA_SHT_THIS_ID, | |
| .sg_tablesize = LIBATA_MAX_PRD, | |
| .max_sectors = ATA_MAX_SECTORS, | |
| .cmd_per_lun = ATA_SHT_CMD_PER_LUN, | |
| .emulated = ATA_SHT_EMULATED, | |
| .use_clustering = ATA_SHT_USE_CLUSTERING, | |
| .proc_name = DRV_NAME, | |
| .dma_boundary = ATA_DMA_BOUNDARY, | |
| .slave_configure = ata_scsi_slave_config, | |
| .bios_param = ata_std_bios_param, | |
| }; | |
| static struct ata_port_operations hpt3x3_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = hpt3x3_set_piomode, | |
| .set_dmamode = hpt3x3_set_dmamode, | |
| .mode_filter = ata_pci_default_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = hpt3x3_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = ata_bmdma_start, | |
| .bmdma_stop = ata_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /** | |
| * hpt3x3_init_one - Initialise an HPT343/363 | |
| * @dev: PCI device | |
| * @id: Entry in match table | |
| * | |
| * Perform basic initialisation. The chip has a quirk that it won't | |
| * function unless it is at XX00. The old ATA driver touched this up | |
| * but we leave it for pci quirks to do properly. | |
| */ | |
| static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| static struct ata_port_info info = { | |
| .sht = &hpt3x3_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x07, | |
| .port_ops = &hpt3x3_port_ops | |
| }; | |
| static struct ata_port_info *port_info[2] = { &info, &info }; | |
| u16 cmd; | |
| /* Initialize the board */ | |
| pci_write_config_word(dev, 0x80, 0x00); | |
| /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */ | |
| pci_read_config_word(dev, PCI_COMMAND, &cmd); | |
| if (cmd & PCI_COMMAND_MEMORY) | |
| pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0); | |
| else | |
| pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); | |
| /* Now kick off ATA set up */ | |
| return ata_pci_init_one(dev, port_info, 2); | |
| } | |
| static const struct pci_device_id hpt3x3[] = { | |
| { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), }, | |
| { }, | |
| }; | |
| static struct pci_driver hpt3x3_pci_driver = { | |
| .name = DRV_NAME, | |
| .id_table = hpt3x3, | |
| .probe = hpt3x3_init_one, | |
| .remove = ata_pci_remove_one | |
| }; | |
| static int __init hpt3x3_init(void) | |
| { | |
| return pci_register_driver(&hpt3x3_pci_driver); | |
| } | |
| static void __exit hpt3x3_exit(void) | |
| { | |
| pci_unregister_driver(&hpt3x3_pci_driver); | |
| } | |
| MODULE_AUTHOR("Alan Cox"); | |
| MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DEVICE_TABLE(pci, hpt3x3); | |
| MODULE_VERSION(DRV_VERSION); | |
| module_init(hpt3x3_init); | |
| module_exit(hpt3x3_exit); |