| /* | |
| * ata-it821x.c - IT821x PATA for new ATA layer | |
| * (C) 2005 Red Hat Inc | |
| * Alan Cox <alan@redhat.com> | |
| * | |
| * based upon | |
| * | |
| * it821x.c | |
| * | |
| * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004 | |
| * | |
| * Copyright (C) 2004 Red Hat <alan@redhat.com> | |
| * | |
| * May be copied or modified under the terms of the GNU General Public License | |
| * Based in part on the ITE vendor provided SCSI driver. | |
| * | |
| * Documentation available from | |
| * http://www.ite.com.tw/pc/IT8212F_V04.pdf | |
| * Some other documents are NDA. | |
| * | |
| * The ITE8212 isn't exactly a standard IDE controller. It has two | |
| * modes. In pass through mode then it is an IDE controller. In its smart | |
| * mode its actually quite a capable hardware raid controller disguised | |
| * as an IDE controller. Smart mode only understands DMA read/write and | |
| * identify, none of the fancier commands apply. The IT8211 is identical | |
| * in other respects but lacks the raid mode. | |
| * | |
| * Errata: | |
| * o Rev 0x10 also requires master/slave hold the same DMA timings and | |
| * cannot do ATAPI MWDMA. | |
| * o The identify data for raid volumes lacks CHS info (technically ok) | |
| * but also fails to set the LBA28 and other bits. We fix these in | |
| * the IDE probe quirk code. | |
| * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode | |
| * raid then the controller firmware dies | |
| * o Smart mode without RAID doesn't clear all the necessary identify | |
| * bits to reduce the command set to the one used | |
| * | |
| * This has a few impacts on the driver | |
| * - In pass through mode we do all the work you would expect | |
| * - In smart mode the clocking set up is done by the controller generally | |
| * but we must watch the other limits and filter. | |
| * - There are a few extra vendor commands that actually talk to the | |
| * controller but only work PIO with no IRQ. | |
| * | |
| * Vendor areas of the identify block in smart mode are used for the | |
| * timing and policy set up. Each HDD in raid mode also has a serial | |
| * block on the disk. The hardware extra commands are get/set chip status, | |
| * rebuild, get rebuild status. | |
| * | |
| * In Linux the driver supports pass through mode as if the device was | |
| * just another IDE controller. If the smart mode is running then | |
| * volumes are managed by the controller firmware and each IDE "disk" | |
| * is a raid volume. Even more cute - the controller can do automated | |
| * hotplug and rebuild. | |
| * | |
| * The pass through controller itself is a little demented. It has a | |
| * flaw that it has a single set of PIO/MWDMA timings per channel so | |
| * non UDMA devices restrict each others performance. It also has a | |
| * single clock source per channel so mixed UDMA100/133 performance | |
| * isn't perfect and we have to pick a clock. Thankfully none of this | |
| * matters in smart mode. ATAPI DMA is not currently supported. | |
| * | |
| * It seems the smart mode is a win for RAID1/RAID10 but otherwise not. | |
| * | |
| * TODO | |
| * - ATAPI and other speed filtering | |
| * - Command filter in smart mode | |
| * - RAID configuration ioctls | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/pci.h> | |
| #include <linux/init.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/delay.h> | |
| #include <scsi/scsi_host.h> | |
| #include <linux/libata.h> | |
| #define DRV_NAME "pata_it821x" | |
| #define DRV_VERSION "0.3.2" | |
| struct it821x_dev | |
| { | |
| unsigned int smart:1, /* Are we in smart raid mode */ | |
| timing10:1; /* Rev 0x10 */ | |
| u8 clock_mode; /* 0, ATA_50 or ATA_66 */ | |
| u8 want[2][2]; /* Mode/Pri log for master slave */ | |
| /* We need these for switching the clock when DMA goes on/off | |
| The high byte is the 66Mhz timing */ | |
| u16 pio[2]; /* Cached PIO values */ | |
| u16 mwdma[2]; /* Cached MWDMA values */ | |
| u16 udma[2]; /* Cached UDMA values (per drive) */ | |
| u16 last_device; /* Master or slave loaded ? */ | |
| }; | |
| #define ATA_66 0 | |
| #define ATA_50 1 | |
| #define ATA_ANY 2 | |
| #define UDMA_OFF 0 | |
| #define MWDMA_OFF 0 | |
| /* | |
| * We allow users to force the card into non raid mode without | |
| * flashing the alternative BIOS. This is also neccessary right now | |
| * for embedded platforms that cannot run a PC BIOS but are using this | |
| * device. | |
| */ | |
| static int it8212_noraid; | |
| /** | |
| * it821x_pre_reset - probe | |
| * @ap: ATA port | |
| * | |
| * Set the cable type | |
| */ | |
| static int it821x_pre_reset(struct ata_port *ap) | |
| { | |
| ap->cbl = ATA_CBL_PATA80; | |
| return ata_std_prereset(ap); | |
| } | |
| /** | |
| * it821x_error_handler - probe/reset | |
| * @ap: ATA port | |
| * | |
| * Set the cable type and trigger a probe | |
| */ | |
| static void it821x_error_handler(struct ata_port *ap) | |
| { | |
| return ata_bmdma_drive_eh(ap, it821x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); | |
| } | |
| /** | |
| * it821x_program - program the PIO/MWDMA registers | |
| * @ap: ATA port | |
| * @adev: Device to program | |
| * @timing: Timing value (66Mhz in top 8bits, 50 in the low 8) | |
| * | |
| * Program the PIO/MWDMA timing for this channel according to the | |
| * current clock. These share the same register so are managed by | |
| * the DMA start/stop sequence as with the old driver. | |
| */ | |
| static void it821x_program(struct ata_port *ap, struct ata_device *adev, u16 timing) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| struct it821x_dev *itdev = ap->private_data; | |
| int channel = ap->port_no; | |
| u8 conf; | |
| /* Program PIO/MWDMA timing bits */ | |
| if (itdev->clock_mode == ATA_66) | |
| conf = timing >> 8; | |
| else | |
| conf = timing & 0xFF; | |
| pci_write_config_byte(pdev, 0x54 + 4 * channel, conf); | |
| } | |
| /** | |
| * it821x_program_udma - program the UDMA registers | |
| * @ap: ATA port | |
| * @adev: ATA device to update | |
| * @timing: Timing bits. Top 8 are for 66Mhz bottom for 50Mhz | |
| * | |
| * Program the UDMA timing for this drive according to the | |
| * current clock. Handles the dual clocks and also knows about | |
| * the errata on the 0x10 revision. The UDMA errata is partly handled | |
| * here and partly in start_dma. | |
| */ | |
| static void it821x_program_udma(struct ata_port *ap, struct ata_device *adev, u16 timing) | |
| { | |
| struct it821x_dev *itdev = ap->private_data; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| int channel = ap->port_no; | |
| int unit = adev->devno; | |
| u8 conf; | |
| /* Program UDMA timing bits */ | |
| if (itdev->clock_mode == ATA_66) | |
| conf = timing >> 8; | |
| else | |
| conf = timing & 0xFF; | |
| if (itdev->timing10 == 0) | |
| pci_write_config_byte(pdev, 0x56 + 4 * channel + unit, conf); | |
| else { | |
| /* Early revision must be programmed for both together */ | |
| pci_write_config_byte(pdev, 0x56 + 4 * channel, conf); | |
| pci_write_config_byte(pdev, 0x56 + 4 * channel + 1, conf); | |
| } | |
| } | |
| /** | |
| * it821x_clock_strategy | |
| * @ap: ATA interface | |
| * @adev: ATA device being updated | |
| * | |
| * Select between the 50 and 66Mhz base clocks to get the best | |
| * results for this interface. | |
| */ | |
| static void it821x_clock_strategy(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| struct it821x_dev *itdev = ap->private_data; | |
| u8 unit = adev->devno; | |
| struct ata_device *pair = ata_dev_pair(adev); | |
| int clock, altclock; | |
| u8 v; | |
| int sel = 0; | |
| /* Look for the most wanted clocking */ | |
| if (itdev->want[0][0] > itdev->want[1][0]) { | |
| clock = itdev->want[0][1]; | |
| altclock = itdev->want[1][1]; | |
| } else { | |
| clock = itdev->want[1][1]; | |
| altclock = itdev->want[0][1]; | |
| } | |
| /* Master doesn't care does the slave ? */ | |
| if (clock == ATA_ANY) | |
| clock = altclock; | |
| /* Nobody cares - keep the same clock */ | |
| if (clock == ATA_ANY) | |
| return; | |
| /* No change */ | |
| if (clock == itdev->clock_mode) | |
| return; | |
| /* Load this into the controller */ | |
| if (clock == ATA_66) | |
| itdev->clock_mode = ATA_66; | |
| else { | |
| itdev->clock_mode = ATA_50; | |
| sel = 1; | |
| } | |
| pci_read_config_byte(pdev, 0x50, &v); | |
| v &= ~(1 << (1 + ap->port_no)); | |
| v |= sel << (1 + ap->port_no); | |
| pci_write_config_byte(pdev, 0x50, v); | |
| /* | |
| * Reprogram the UDMA/PIO of the pair drive for the switch | |
| * MWDMA will be dealt with by the dma switcher | |
| */ | |
| if (pair && itdev->udma[1-unit] != UDMA_OFF) { | |
| it821x_program_udma(ap, pair, itdev->udma[1-unit]); | |
| it821x_program(ap, pair, itdev->pio[1-unit]); | |
| } | |
| /* | |
| * Reprogram the UDMA/PIO of our drive for the switch. | |
| * MWDMA will be dealt with by the dma switcher | |
| */ | |
| if (itdev->udma[unit] != UDMA_OFF) { | |
| it821x_program_udma(ap, adev, itdev->udma[unit]); | |
| it821x_program(ap, adev, itdev->pio[unit]); | |
| } | |
| } | |
| /** | |
| * it821x_passthru_set_piomode - set PIO mode data | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Configure for PIO mode. This is complicated as the register is | |
| * shared by PIO and MWDMA and for both channels. | |
| */ | |
| static void it821x_passthru_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| /* Spec says 89 ref driver uses 88 */ | |
| static const u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 }; | |
| static const u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY }; | |
| struct it821x_dev *itdev = ap->private_data; | |
| int unit = adev->devno; | |
| int mode_wanted = adev->pio_mode - XFER_PIO_0; | |
| /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */ | |
| itdev->want[unit][1] = pio_want[mode_wanted]; | |
| itdev->want[unit][0] = 1; /* PIO is lowest priority */ | |
| itdev->pio[unit] = pio[mode_wanted]; | |
| it821x_clock_strategy(ap, adev); | |
| it821x_program(ap, adev, itdev->pio[unit]); | |
| } | |
| /** | |
| * it821x_passthru_set_dmamode - set initial DMA mode data | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Set up the DMA modes. The actions taken depend heavily on the mode | |
| * to use. If UDMA is used as is hopefully the usual case then the | |
| * timing register is private and we need only consider the clock. If | |
| * we are using MWDMA then we have to manage the setting ourself as | |
| * we switch devices and mode. | |
| */ | |
| static void it821x_passthru_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| static const u16 dma[] = { 0x8866, 0x3222, 0x3121 }; | |
| static const u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY }; | |
| static const u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 }; | |
| static const u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 }; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| struct it821x_dev *itdev = ap->private_data; | |
| int channel = ap->port_no; | |
| int unit = adev->devno; | |
| u8 conf; | |
| if (adev->dma_mode >= XFER_UDMA_0) { | |
| int mode_wanted = adev->dma_mode - XFER_UDMA_0; | |
| itdev->want[unit][1] = udma_want[mode_wanted]; | |
| itdev->want[unit][0] = 3; /* UDMA is high priority */ | |
| itdev->mwdma[unit] = MWDMA_OFF; | |
| itdev->udma[unit] = udma[mode_wanted]; | |
| if (mode_wanted >= 5) | |
| itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */ | |
| /* UDMA on. Again revision 0x10 must do the pair */ | |
| pci_read_config_byte(pdev, 0x50, &conf); | |
| if (itdev->timing10) | |
| conf &= channel ? 0x9F: 0xE7; | |
| else | |
| conf &= ~ (1 << (3 + 2 * channel + unit)); | |
| pci_write_config_byte(pdev, 0x50, conf); | |
| it821x_clock_strategy(ap, adev); | |
| it821x_program_udma(ap, adev, itdev->udma[unit]); | |
| } else { | |
| int mode_wanted = adev->dma_mode - XFER_MW_DMA_0; | |
| itdev->want[unit][1] = mwdma_want[mode_wanted]; | |
| itdev->want[unit][0] = 2; /* MWDMA is low priority */ | |
| itdev->mwdma[unit] = dma[mode_wanted]; | |
| itdev->udma[unit] = UDMA_OFF; | |
| /* UDMA bits off - Revision 0x10 do them in pairs */ | |
| pci_read_config_byte(pdev, 0x50, &conf); | |
| if (itdev->timing10) | |
| conf |= channel ? 0x60: 0x18; | |
| else | |
| conf |= 1 << (3 + 2 * channel + unit); | |
| pci_write_config_byte(pdev, 0x50, conf); | |
| it821x_clock_strategy(ap, adev); | |
| } | |
| } | |
| /** | |
| * it821x_passthru_dma_start - DMA start callback | |
| * @qc: Command in progress | |
| * | |
| * Usually drivers set the DMA timing at the point the set_dmamode call | |
| * is made. IT821x however requires we load new timings on the | |
| * transitions in some cases. | |
| */ | |
| static void it821x_passthru_bmdma_start(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct ata_device *adev = qc->dev; | |
| struct it821x_dev *itdev = ap->private_data; | |
| int unit = adev->devno; | |
| if (itdev->mwdma[unit] != MWDMA_OFF) | |
| it821x_program(ap, adev, itdev->mwdma[unit]); | |
| else if (itdev->udma[unit] != UDMA_OFF && itdev->timing10) | |
| it821x_program_udma(ap, adev, itdev->udma[unit]); | |
| ata_bmdma_start(qc); | |
| } | |
| /** | |
| * it821x_passthru_dma_stop - DMA stop callback | |
| * @qc: ATA command | |
| * | |
| * We loaded new timings in dma_start, as a result we need to restore | |
| * the PIO timings in dma_stop so that the next command issue gets the | |
| * right clock values. | |
| */ | |
| static void it821x_passthru_bmdma_stop(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct ata_device *adev = qc->dev; | |
| struct it821x_dev *itdev = ap->private_data; | |
| int unit = adev->devno; | |
| ata_bmdma_stop(qc); | |
| if (itdev->mwdma[unit] != MWDMA_OFF) | |
| it821x_program(ap, adev, itdev->pio[unit]); | |
| } | |
| /** | |
| * it821x_passthru_dev_select - Select master/slave | |
| * @ap: ATA port | |
| * @device: Device number (not pointer) | |
| * | |
| * Device selection hook. If neccessary perform clock switching | |
| */ | |
| static void it821x_passthru_dev_select(struct ata_port *ap, | |
| unsigned int device) | |
| { | |
| struct it821x_dev *itdev = ap->private_data; | |
| if (itdev && device != itdev->last_device) { | |
| struct ata_device *adev = &ap->device[device]; | |
| it821x_program(ap, adev, itdev->pio[adev->devno]); | |
| itdev->last_device = device; | |
| } | |
| ata_std_dev_select(ap, device); | |
| } | |
| /** | |
| * it821x_smart_qc_issue_prot - wrap qc issue prot | |
| * @qc: command | |
| * | |
| * Wrap the command issue sequence for the IT821x. We need to | |
| * perform out own device selection timing loads before the | |
| * usual happenings kick off | |
| */ | |
| static unsigned int it821x_smart_qc_issue_prot(struct ata_queued_cmd *qc) | |
| { | |
| switch(qc->tf.command) | |
| { | |
| /* Commands the firmware supports */ | |
| case ATA_CMD_READ: | |
| case ATA_CMD_READ_EXT: | |
| case ATA_CMD_WRITE: | |
| case ATA_CMD_WRITE_EXT: | |
| case ATA_CMD_PIO_READ: | |
| case ATA_CMD_PIO_READ_EXT: | |
| case ATA_CMD_PIO_WRITE: | |
| case ATA_CMD_PIO_WRITE_EXT: | |
| case ATA_CMD_READ_MULTI: | |
| case ATA_CMD_READ_MULTI_EXT: | |
| case ATA_CMD_WRITE_MULTI: | |
| case ATA_CMD_WRITE_MULTI_EXT: | |
| case ATA_CMD_ID_ATA: | |
| /* Arguably should just no-op this one */ | |
| case ATA_CMD_SET_FEATURES: | |
| return ata_qc_issue_prot(qc); | |
| } | |
| printk(KERN_DEBUG "it821x: can't process command 0x%02X\n", qc->tf.command); | |
| return AC_ERR_INVALID; | |
| } | |
| /** | |
| * it821x_passthru_qc_issue_prot - wrap qc issue prot | |
| * @qc: command | |
| * | |
| * Wrap the command issue sequence for the IT821x. We need to | |
| * perform out own device selection timing loads before the | |
| * usual happenings kick off | |
| */ | |
| static unsigned int it821x_passthru_qc_issue_prot(struct ata_queued_cmd *qc) | |
| { | |
| it821x_passthru_dev_select(qc->ap, qc->dev->devno); | |
| return ata_qc_issue_prot(qc); | |
| } | |
| /** | |
| * it821x_smart_set_mode - mode setting | |
| * @ap: interface to set up | |
| * | |
| * Use a non standard set_mode function. We don't want to be tuned. | |
| * The BIOS configured everything. Our job is not to fiddle. We | |
| * read the dma enabled bits from the PCI configuration of the device | |
| * and respect them. | |
| */ | |
| static void it821x_smart_set_mode(struct ata_port *ap) | |
| { | |
| int dma_enabled = 0; | |
| int i; | |
| /* Bits 5 and 6 indicate if DMA is active on master/slave */ | |
| /* It is possible that BMDMA isn't allocated */ | |
| if (ap->ioaddr.bmdma_addr) | |
| dma_enabled = inb(ap->ioaddr.bmdma_addr + ATA_DMA_CMD); | |
| for (i = 0; i < ATA_MAX_DEVICES; i++) { | |
| struct ata_device *dev = &ap->device[i]; | |
| if (ata_dev_enabled(dev)) { | |
| /* We don't really care */ | |
| dev->pio_mode = XFER_PIO_0; | |
| dev->dma_mode = XFER_MW_DMA_0; | |
| /* We do need the right mode information for DMA or PIO | |
| and this comes from the current configuration flags */ | |
| if (dma_enabled & (1 << (5 + i))) { | |
| dev->xfer_mode = XFER_MW_DMA_0; | |
| dev->xfer_shift = ATA_SHIFT_MWDMA; | |
| dev->flags &= ~ATA_DFLAG_PIO; | |
| } else { | |
| dev->xfer_mode = XFER_PIO_0; | |
| dev->xfer_shift = ATA_SHIFT_PIO; | |
| dev->flags |= ATA_DFLAG_PIO; | |
| } | |
| } | |
| } | |
| } | |
| /** | |
| * it821x_dev_config - Called each device identify | |
| * @ap: ATA port | |
| * @adev: Device that has just been identified | |
| * | |
| * Perform the initial setup needed for each device that is chip | |
| * special. In our case we need to lock the sector count to avoid | |
| * blowing the brains out of the firmware with large LBA48 requests | |
| * | |
| * FIXME: When FUA appears we need to block FUA too. And SMART and | |
| * basically we need to filter commands for this chip. | |
| */ | |
| static void it821x_dev_config(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| unsigned char model_num[40]; | |
| char *s; | |
| unsigned int len; | |
| /* This block ought to be a library routine as it is in several | |
| drivers now */ | |
| ata_id_string(adev->id, model_num, ATA_ID_PROD_OFS, | |
| sizeof(model_num)); | |
| s = &model_num[0]; | |
| len = strnlen(s, sizeof(model_num)); | |
| /* ATAPI specifies that empty space is blank-filled; remove blanks */ | |
| while ((len > 0) && (s[len - 1] == ' ')) { | |
| len--; | |
| s[len] = 0; | |
| } | |
| if (adev->max_sectors > 255) | |
| adev->max_sectors = 255; | |
| if (strstr(model_num, "Integrated Technology Express")) { | |
| /* RAID mode */ | |
| printk(KERN_INFO "IT821x %sRAID%d volume", | |
| adev->id[147]?"Bootable ":"", | |
| adev->id[129]); | |
| if (adev->id[129] != 1) | |
| printk("(%dK stripe)", adev->id[146]); | |
| printk(".\n"); | |
| } | |
| } | |
| /** | |
| * it821x_check_atapi_dma - ATAPI DMA handler | |
| * @qc: Command we are about to issue | |
| * | |
| * Decide if this ATAPI command can be issued by DMA on this | |
| * controller. Return 0 if it can be. | |
| */ | |
| static int it821x_check_atapi_dma(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| struct it821x_dev *itdev = ap->private_data; | |
| /* No ATAPI DMA in smart mode */ | |
| if (itdev->smart) | |
| return -EOPNOTSUPP; | |
| /* No ATAPI DMA on rev 10 */ | |
| if (itdev->timing10) | |
| return -EOPNOTSUPP; | |
| /* Cool */ | |
| return 0; | |
| } | |
| /** | |
| * it821x_port_start - port setup | |
| * @ap: ATA port being set up | |
| * | |
| * The it821x needs to maintain private data structures and also to | |
| * use the standard PCI interface which lacks support for this | |
| * functionality. We instead set up the private data on the port | |
| * start hook, and tear it down on port stop | |
| */ | |
| static int it821x_port_start(struct ata_port *ap) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| struct it821x_dev *itdev; | |
| u8 conf; | |
| int ret = ata_port_start(ap); | |
| if (ret < 0) | |
| return ret; | |
| ap->private_data = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL); | |
| if (ap->private_data == NULL) { | |
| ata_port_stop(ap); | |
| return -ENOMEM; | |
| } | |
| itdev = ap->private_data; | |
| memset(itdev, 0, sizeof(struct it821x_dev)); | |
| pci_read_config_byte(pdev, 0x50, &conf); | |
| if (conf & 1) { | |
| itdev->smart = 1; | |
| /* Long I/O's although allowed in LBA48 space cause the | |
| onboard firmware to enter the twighlight zone */ | |
| /* No ATAPI DMA in this mode either */ | |
| } | |
| /* Pull the current clocks from 0x50 */ | |
| if (conf & (1 << (1 + ap->port_no))) | |
| itdev->clock_mode = ATA_50; | |
| else | |
| itdev->clock_mode = ATA_66; | |
| itdev->want[0][1] = ATA_ANY; | |
| itdev->want[1][1] = ATA_ANY; | |
| itdev->last_device = -1; | |
| pci_read_config_byte(pdev, PCI_REVISION_ID, &conf); | |
| if (conf == 0x10) { | |
| itdev->timing10 = 1; | |
| /* Need to disable ATAPI DMA for this case */ | |
| if (!itdev->smart) | |
| printk(KERN_WARNING DRV_NAME": Revision 0x10, workarounds activated.\n"); | |
| } | |
| return 0; | |
| } | |
| /** | |
| * it821x_port_stop - port shutdown | |
| * @ap: ATA port being removed | |
| * | |
| * Release the private objects we added in it821x_port_start | |
| */ | |
| static void it821x_port_stop(struct ata_port *ap) { | |
| kfree(ap->private_data); | |
| ap->private_data = NULL; /* We want an OOPS if we reuse this | |
| too late! */ | |
| ata_port_stop(ap); | |
| } | |
| static struct scsi_host_template it821x_sht = { | |
| .module = THIS_MODULE, | |
| .name = DRV_NAME, | |
| .ioctl = ata_scsi_ioctl, | |
| .queuecommand = ata_scsi_queuecmd, | |
| .can_queue = ATA_DEF_QUEUE, | |
| .this_id = ATA_SHT_THIS_ID, | |
| .sg_tablesize = LIBATA_MAX_PRD, | |
| /* 255 sectors to begin with. This is locked in smart mode but not | |
| in pass through */ | |
| .max_sectors = 255, | |
| .cmd_per_lun = ATA_SHT_CMD_PER_LUN, | |
| .emulated = ATA_SHT_EMULATED, | |
| .use_clustering = ATA_SHT_USE_CLUSTERING, | |
| .proc_name = DRV_NAME, | |
| .dma_boundary = ATA_DMA_BOUNDARY, | |
| .slave_configure = ata_scsi_slave_config, | |
| .bios_param = ata_std_bios_param, | |
| }; | |
| static struct ata_port_operations it821x_smart_port_ops = { | |
| .set_mode = it821x_smart_set_mode, | |
| .port_disable = ata_port_disable, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .mode_filter = ata_pci_default_filter, | |
| .check_status = ata_check_status, | |
| .check_atapi_dma= it821x_check_atapi_dma, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .dev_config = it821x_dev_config, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = it821x_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = ata_bmdma_start, | |
| .bmdma_stop = ata_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = it821x_smart_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = it821x_port_start, | |
| .port_stop = it821x_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| static struct ata_port_operations it821x_passthru_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = it821x_passthru_set_piomode, | |
| .set_dmamode = it821x_passthru_set_dmamode, | |
| .mode_filter = ata_pci_default_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .check_atapi_dma= it821x_check_atapi_dma, | |
| .dev_select = it821x_passthru_dev_select, | |
| .freeze = ata_bmdma_freeze, | |
| .thaw = ata_bmdma_thaw, | |
| .error_handler = it821x_error_handler, | |
| .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = it821x_passthru_bmdma_start, | |
| .bmdma_stop = it821x_passthru_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = it821x_passthru_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .irq_handler = ata_interrupt, | |
| .port_start = it821x_port_start, | |
| .port_stop = it821x_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| static void __devinit it821x_disable_raid(struct pci_dev *pdev) | |
| { | |
| /* Reset local CPU, and set BIOS not ready */ | |
| pci_write_config_byte(pdev, 0x5E, 0x01); | |
| /* Set to bypass mode, and reset PCI bus */ | |
| pci_write_config_byte(pdev, 0x50, 0x00); | |
| pci_write_config_word(pdev, PCI_COMMAND, | |
| PCI_COMMAND_PARITY | PCI_COMMAND_IO | | |
| PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); | |
| pci_write_config_word(pdev, 0x40, 0xA0F3); | |
| pci_write_config_dword(pdev,0x4C, 0x02040204); | |
| pci_write_config_byte(pdev, 0x42, 0x36); | |
| pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20); | |
| } | |
| static int it821x_init_one(struct pci_dev *pdev, const struct pci_device_id *id) | |
| { | |
| u8 conf; | |
| static struct ata_port_info info_smart = { | |
| .sht = &it821x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .port_ops = &it821x_smart_port_ops | |
| }; | |
| static struct ata_port_info info_passthru = { | |
| .sht = &it821x_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .udma_mask = 0x7f, | |
| .port_ops = &it821x_passthru_port_ops | |
| }; | |
| static struct ata_port_info *port_info[2]; | |
| static char *mode[2] = { "pass through", "smart" }; | |
| /* Force the card into bypass mode if so requested */ | |
| if (it8212_noraid) { | |
| printk(KERN_INFO DRV_NAME ": forcing bypass mode.\n"); | |
| it821x_disable_raid(pdev); | |
| } | |
| pci_read_config_byte(pdev, 0x50, &conf); | |
| conf &= 1; | |
| printk(KERN_INFO DRV_NAME ": controller in %s mode.\n", mode[conf]); | |
| if (conf == 0) | |
| port_info[0] = port_info[1] = &info_passthru; | |
| else | |
| port_info[0] = port_info[1] = &info_smart; | |
| return ata_pci_init_one(pdev, port_info, 2); | |
| } | |
| static const struct pci_device_id it821x[] = { | |
| { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8211), }, | |
| { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8212), }, | |
| { }, | |
| }; | |
| static struct pci_driver it821x_pci_driver = { | |
| .name = DRV_NAME, | |
| .id_table = it821x, | |
| .probe = it821x_init_one, | |
| .remove = ata_pci_remove_one | |
| }; | |
| static int __init it821x_init(void) | |
| { | |
| return pci_register_driver(&it821x_pci_driver); | |
| } | |
| static void __exit it821x_exit(void) | |
| { | |
| pci_unregister_driver(&it821x_pci_driver); | |
| } | |
| MODULE_AUTHOR("Alan Cox"); | |
| MODULE_DESCRIPTION("low-level driver for the IT8211/IT8212 IDE RAID controller"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DEVICE_TABLE(pci, it821x); | |
| MODULE_VERSION(DRV_VERSION); | |
| module_param_named(noraid, it8212_noraid, int, S_IRUGO); | |
| MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode"); | |
| module_init(it821x_init); | |
| module_exit(it821x_exit); |