| /* | |
| * pata_sl82c105.c - SL82C105 PATA for new ATA layer | |
| * (C) 2005 Red Hat Inc | |
| * Alan Cox <alan@redhat.com> | |
| * | |
| * Based in part on linux/drivers/ide/pci/sl82c105.c | |
| * SL82C105/Winbond 553 IDE driver | |
| * | |
| * and in part on the documentation and errata sheet | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/pci.h> | |
| #include <linux/init.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/delay.h> | |
| #include <scsi/scsi_host.h> | |
| #include <linux/libata.h> | |
| #define DRV_NAME "pata_sl82c105" | |
| #define DRV_VERSION "0.2.3" | |
| enum { | |
| /* | |
| * SL82C105 PCI config register 0x40 bits. | |
| */ | |
| CTRL_IDE_IRQB = (1 << 30), | |
| CTRL_IDE_IRQA = (1 << 28), | |
| CTRL_LEGIRQ = (1 << 11), | |
| CTRL_P1F16 = (1 << 5), | |
| CTRL_P1EN = (1 << 4), | |
| CTRL_P0F16 = (1 << 1), | |
| CTRL_P0EN = (1 << 0) | |
| }; | |
| /** | |
| * sl82c105_pre_reset - probe begin | |
| * @ap: ATA port | |
| * | |
| * Set up cable type and use generic probe init | |
| */ | |
| static int sl82c105_pre_reset(struct ata_port *ap) | |
| { | |
| static const struct pci_bits sl82c105_enable_bits[] = { | |
| { 0x40, 1, 0x01, 0x01 }, | |
| { 0x40, 1, 0x10, 0x10 } | |
| }; | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no])) | |
| return -ENOENT; | |
| ap->cbl = ATA_CBL_PATA40; | |
| return ata_std_prereset(ap); | |
| } | |
| static void sl82c105_error_handler(struct ata_port *ap) | |
| { | |
| ata_bmdma_drive_eh(ap, sl82c105_pre_reset, ata_std_softreset, NULL, ata_std_postreset); | |
| } | |
| /** | |
| * sl82c105_configure_piomode - set chip PIO timing | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * @pio: PIO mode | |
| * | |
| * Called to do the PIO mode setup. Our timing registers are shared | |
| * so a configure_dmamode call will undo any work we do here and vice | |
| * versa | |
| */ | |
| static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| static u16 pio_timing[5] = { | |
| 0x50D, 0x407, 0x304, 0x242, 0x240 | |
| }; | |
| u16 dummy; | |
| int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno); | |
| pci_write_config_word(pdev, timing, pio_timing[pio]); | |
| /* Can we lose this oddity of the old driver */ | |
| pci_read_config_word(pdev, timing, &dummy); | |
| } | |
| /** | |
| * sl82c105_set_piomode - set initial PIO mode data | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Called to do the PIO mode setup. Our timing registers are shared | |
| * but we want to set the PIO timing by default. | |
| */ | |
| static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0); | |
| } | |
| /** | |
| * sl82c105_configure_dmamode - set DMA mode in chip | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Load DMA cycle times into the chip ready for a DMA transfer | |
| * to occur. | |
| */ | |
| static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| static u16 dma_timing[3] = { | |
| 0x707, 0x201, 0x200 | |
| }; | |
| u16 dummy; | |
| int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno); | |
| int dma = adev->dma_mode - XFER_MW_DMA_0; | |
| pci_write_config_word(pdev, timing, dma_timing[dma]); | |
| /* Can we lose this oddity of the old driver */ | |
| pci_read_config_word(pdev, timing, &dummy); | |
| } | |
| /** | |
| * sl82c105_set_dmamode - set initial DMA mode data | |
| * @ap: ATA interface | |
| * @adev: ATA device | |
| * | |
| * Called to do the DMA mode setup. This replaces the PIO timings | |
| * for the device in question. Set appropriate PIO timings not DMA | |
| * timings at this point. | |
| */ | |
| static void sl82c105_set_dmamode(struct ata_port *ap, struct ata_device *adev) | |
| { | |
| switch(adev->dma_mode) { | |
| case XFER_MW_DMA_0: | |
| sl82c105_configure_piomode(ap, adev, 1); | |
| break; | |
| case XFER_MW_DMA_1: | |
| sl82c105_configure_piomode(ap, adev, 3); | |
| break; | |
| case XFER_MW_DMA_2: | |
| sl82c105_configure_piomode(ap, adev, 3); | |
| break; | |
| default: | |
| BUG(); | |
| } | |
| } | |
| /** | |
| * sl82c105_reset_engine - Reset the DMA engine | |
| * @ap: ATA interface | |
| * | |
| * The sl82c105 has some serious problems with the DMA engine | |
| * when transfers don't run as expected or ATAPI is used. The | |
| * recommended fix is to reset the engine each use using a chip | |
| * test register. | |
| */ | |
| static void sl82c105_reset_engine(struct ata_port *ap) | |
| { | |
| struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
| u16 val; | |
| pci_read_config_word(pdev, 0x7E, &val); | |
| pci_write_config_word(pdev, 0x7E, val | 4); | |
| pci_write_config_word(pdev, 0x7E, val & ~4); | |
| } | |
| /** | |
| * sl82c105_bmdma_start - DMA engine begin | |
| * @qc: ATA command | |
| * | |
| * Reset the DMA engine each use as recommended by the errata | |
| * document. | |
| * | |
| * FIXME: if we switch clock at BMDMA start/end we might get better | |
| * PIO performance on DMA capable devices. | |
| */ | |
| static void sl82c105_bmdma_start(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| sl82c105_reset_engine(ap); | |
| /* Set the clocks for DMA */ | |
| sl82c105_configure_dmamode(ap, qc->dev); | |
| /* Activate DMA */ | |
| ata_bmdma_start(qc); | |
| } | |
| /** | |
| * sl82c105_bmdma_end - DMA engine stop | |
| * @qc: ATA command | |
| * | |
| * Reset the DMA engine each use as recommended by the errata | |
| * document. | |
| * | |
| * This function is also called to turn off DMA when a timeout occurs | |
| * during DMA operation. In both cases we need to reset the engine, | |
| * so no actual eng_timeout handler is required. | |
| * | |
| * We assume bmdma_stop is always called if bmdma_start as called. If | |
| * not then we may need to wrap qc_issue. | |
| */ | |
| static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc) | |
| { | |
| struct ata_port *ap = qc->ap; | |
| ata_bmdma_stop(qc); | |
| sl82c105_reset_engine(ap); | |
| /* This will redo the initial setup of the DMA device to matching | |
| PIO timings */ | |
| sl82c105_set_dmamode(ap, qc->dev); | |
| } | |
| static struct scsi_host_template sl82c105_sht = { | |
| .module = THIS_MODULE, | |
| .name = DRV_NAME, | |
| .ioctl = ata_scsi_ioctl, | |
| .queuecommand = ata_scsi_queuecmd, | |
| .can_queue = ATA_DEF_QUEUE, | |
| .this_id = ATA_SHT_THIS_ID, | |
| .sg_tablesize = LIBATA_MAX_PRD, | |
| .max_sectors = ATA_MAX_SECTORS, | |
| .cmd_per_lun = ATA_SHT_CMD_PER_LUN, | |
| .emulated = ATA_SHT_EMULATED, | |
| .use_clustering = ATA_SHT_USE_CLUSTERING, | |
| .proc_name = DRV_NAME, | |
| .dma_boundary = ATA_DMA_BOUNDARY, | |
| .slave_configure = ata_scsi_slave_config, | |
| .bios_param = ata_std_bios_param, | |
| }; | |
| static struct ata_port_operations sl82c105_port_ops = { | |
| .port_disable = ata_port_disable, | |
| .set_piomode = sl82c105_set_piomode, | |
| .set_dmamode = sl82c105_set_dmamode, | |
| .mode_filter = ata_pci_default_filter, | |
| .tf_load = ata_tf_load, | |
| .tf_read = ata_tf_read, | |
| .check_status = ata_check_status, | |
| .exec_command = ata_exec_command, | |
| .dev_select = ata_std_dev_select, | |
| .error_handler = sl82c105_error_handler, | |
| .bmdma_setup = ata_bmdma_setup, | |
| .bmdma_start = sl82c105_bmdma_start, | |
| .bmdma_stop = sl82c105_bmdma_stop, | |
| .bmdma_status = ata_bmdma_status, | |
| .qc_prep = ata_qc_prep, | |
| .qc_issue = ata_qc_issue_prot, | |
| .data_xfer = ata_pio_data_xfer, | |
| .irq_handler = ata_interrupt, | |
| .irq_clear = ata_bmdma_irq_clear, | |
| .port_start = ata_port_start, | |
| .port_stop = ata_port_stop, | |
| .host_stop = ata_host_stop | |
| }; | |
| /** | |
| * sl82c105_bridge_revision - find bridge version | |
| * @pdev: PCI device for the ATA function | |
| * | |
| * Locates the PCI bridge associated with the ATA function and | |
| * providing it is a Winbond 553 reports the revision. If it cannot | |
| * find a revision or the right device it returns -1 | |
| */ | |
| static int sl82c105_bridge_revision(struct pci_dev *pdev) | |
| { | |
| struct pci_dev *bridge; | |
| u8 rev; | |
| /* | |
| * The bridge should be part of the same device, but function 0. | |
| */ | |
| bridge = pci_get_slot(pdev->bus, | |
| PCI_DEVFN(PCI_SLOT(pdev->devfn), 0)); | |
| if (!bridge) | |
| return -1; | |
| /* | |
| * Make sure it is a Winbond 553 and is an ISA bridge. | |
| */ | |
| if (bridge->vendor != PCI_VENDOR_ID_WINBOND || | |
| bridge->device != PCI_DEVICE_ID_WINBOND_83C553 || | |
| bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) { | |
| pci_dev_put(bridge); | |
| return -1; | |
| } | |
| /* | |
| * We need to find function 0's revision, not function 1 | |
| */ | |
| pci_read_config_byte(bridge, PCI_REVISION_ID, &rev); | |
| pci_dev_put(bridge); | |
| return rev; | |
| } | |
| static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| static struct ata_port_info info_dma = { | |
| .sht = &sl82c105_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .mwdma_mask = 0x07, | |
| .port_ops = &sl82c105_port_ops | |
| }; | |
| static struct ata_port_info info_early = { | |
| .sht = &sl82c105_sht, | |
| .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST, | |
| .pio_mask = 0x1f, | |
| .port_ops = &sl82c105_port_ops | |
| }; | |
| static struct ata_port_info *port_info[2] = { &info_early, &info_early }; | |
| u32 val; | |
| int rev; | |
| rev = sl82c105_bridge_revision(dev); | |
| if (rev == -1) | |
| dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n"); | |
| else if (rev <= 5) | |
| dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n"); | |
| else { | |
| port_info[0] = &info_dma; | |
| port_info[1] = &info_dma; | |
| } | |
| pci_read_config_dword(dev, 0x40, &val); | |
| val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16; | |
| pci_write_config_dword(dev, 0x40, val); | |
| return ata_pci_init_one(dev, port_info, 1); /* For now */ | |
| } | |
| static const struct pci_device_id sl82c105[] = { | |
| { PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), }, | |
| { }, | |
| }; | |
| static struct pci_driver sl82c105_pci_driver = { | |
| .name = DRV_NAME, | |
| .id_table = sl82c105, | |
| .probe = sl82c105_init_one, | |
| .remove = ata_pci_remove_one | |
| }; | |
| static int __init sl82c105_init(void) | |
| { | |
| return pci_register_driver(&sl82c105_pci_driver); | |
| } | |
| static void __exit sl82c105_exit(void) | |
| { | |
| pci_unregister_driver(&sl82c105_pci_driver); | |
| } | |
| MODULE_AUTHOR("Alan Cox"); | |
| MODULE_DESCRIPTION("low-level driver for Sl82c105"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_DEVICE_TABLE(pci, sl82c105); | |
| MODULE_VERSION(DRV_VERSION); | |
| module_init(sl82c105_init); | |
| module_exit(sl82c105_exit); |