| /* | |
| voodoo3.c - Part of lm_sensors, Linux kernel modules for hardware | |
| monitoring | |
| Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>, | |
| Philip Edelbrock <phil@netroedge.com>, | |
| Ralph Metzler <rjkm@thp.uni-koeln.de>, and | |
| Mark D. Studebaker <mdsxyz123@yahoo.com> | |
| Based on code written by Ralph Metzler <rjkm@thp.uni-koeln.de> and | |
| Simon Vogl | |
| This program is free software; you can redistribute it and/or modify | |
| it under the terms of the GNU General Public License as published by | |
| the Free Software Foundation; either version 2 of the License, or | |
| (at your option) any later version. | |
| This program is distributed in the hope that it will be useful, | |
| but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| GNU General Public License for more details. | |
| You should have received a copy of the GNU General Public License | |
| along with this program; if not, write to the Free Software | |
| Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. | |
| */ | |
| /* This interfaces to the I2C bus of the Voodoo3 to gain access to | |
| the BT869 and possibly other I2C devices. */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/init.h> | |
| #include <linux/pci.h> | |
| #include <linux/i2c.h> | |
| #include <linux/i2c-algo-bit.h> | |
| #include <asm/io.h> | |
| /* the only registers we use */ | |
| #define REG 0x78 | |
| #define REG2 0x70 | |
| /* bit locations in the register */ | |
| #define DDC_ENAB 0x00040000 | |
| #define DDC_SCL_OUT 0x00080000 | |
| #define DDC_SDA_OUT 0x00100000 | |
| #define DDC_SCL_IN 0x00200000 | |
| #define DDC_SDA_IN 0x00400000 | |
| #define I2C_ENAB 0x00800000 | |
| #define I2C_SCL_OUT 0x01000000 | |
| #define I2C_SDA_OUT 0x02000000 | |
| #define I2C_SCL_IN 0x04000000 | |
| #define I2C_SDA_IN 0x08000000 | |
| /* initialization states */ | |
| #define INIT2 0x2 | |
| #define INIT3 0x4 | |
| /* delays */ | |
| #define CYCLE_DELAY 10 | |
| #define TIMEOUT (HZ / 2) | |
| static void __iomem *ioaddr; | |
| /* The voo GPIO registers don't have individual masks for each bit | |
| so we always have to read before writing. */ | |
| static void bit_vooi2c_setscl(void *data, int val) | |
| { | |
| unsigned int r; | |
| r = readl(ioaddr + REG); | |
| if (val) | |
| r |= I2C_SCL_OUT; | |
| else | |
| r &= ~I2C_SCL_OUT; | |
| writel(r, ioaddr + REG); | |
| readl(ioaddr + REG); /* flush posted write */ | |
| } | |
| static void bit_vooi2c_setsda(void *data, int val) | |
| { | |
| unsigned int r; | |
| r = readl(ioaddr + REG); | |
| if (val) | |
| r |= I2C_SDA_OUT; | |
| else | |
| r &= ~I2C_SDA_OUT; | |
| writel(r, ioaddr + REG); | |
| readl(ioaddr + REG); /* flush posted write */ | |
| } | |
| /* The GPIO pins are open drain, so the pins always remain outputs. | |
| We rely on the i2c-algo-bit routines to set the pins high before | |
| reading the input from other chips. */ | |
| static int bit_vooi2c_getscl(void *data) | |
| { | |
| return (0 != (readl(ioaddr + REG) & I2C_SCL_IN)); | |
| } | |
| static int bit_vooi2c_getsda(void *data) | |
| { | |
| return (0 != (readl(ioaddr + REG) & I2C_SDA_IN)); | |
| } | |
| static void bit_vooddc_setscl(void *data, int val) | |
| { | |
| unsigned int r; | |
| r = readl(ioaddr + REG); | |
| if (val) | |
| r |= DDC_SCL_OUT; | |
| else | |
| r &= ~DDC_SCL_OUT; | |
| writel(r, ioaddr + REG); | |
| readl(ioaddr + REG); /* flush posted write */ | |
| } | |
| static void bit_vooddc_setsda(void *data, int val) | |
| { | |
| unsigned int r; | |
| r = readl(ioaddr + REG); | |
| if (val) | |
| r |= DDC_SDA_OUT; | |
| else | |
| r &= ~DDC_SDA_OUT; | |
| writel(r, ioaddr + REG); | |
| readl(ioaddr + REG); /* flush posted write */ | |
| } | |
| static int bit_vooddc_getscl(void *data) | |
| { | |
| return (0 != (readl(ioaddr + REG) & DDC_SCL_IN)); | |
| } | |
| static int bit_vooddc_getsda(void *data) | |
| { | |
| return (0 != (readl(ioaddr + REG) & DDC_SDA_IN)); | |
| } | |
| static int config_v3(struct pci_dev *dev) | |
| { | |
| unsigned long cadr; | |
| /* map Voodoo3 memory */ | |
| cadr = dev->resource[0].start; | |
| cadr &= PCI_BASE_ADDRESS_MEM_MASK; | |
| ioaddr = ioremap_nocache(cadr, 0x1000); | |
| if (ioaddr) { | |
| writel(0x8160, ioaddr + REG2); | |
| writel(0xcffc0020, ioaddr + REG); | |
| dev_info(&dev->dev, "Using Banshee/Voodoo3 I2C device at %p\n", ioaddr); | |
| return 0; | |
| } | |
| return -ENODEV; | |
| } | |
| static struct i2c_algo_bit_data voo_i2c_bit_data = { | |
| .setsda = bit_vooi2c_setsda, | |
| .setscl = bit_vooi2c_setscl, | |
| .getsda = bit_vooi2c_getsda, | |
| .getscl = bit_vooi2c_getscl, | |
| .udelay = CYCLE_DELAY, | |
| .timeout = TIMEOUT | |
| }; | |
| static struct i2c_adapter voodoo3_i2c_adapter = { | |
| .owner = THIS_MODULE, | |
| .class = I2C_CLASS_TV_ANALOG, | |
| .name = "I2C Voodoo3/Banshee adapter", | |
| .algo_data = &voo_i2c_bit_data, | |
| }; | |
| static struct i2c_algo_bit_data voo_ddc_bit_data = { | |
| .setsda = bit_vooddc_setsda, | |
| .setscl = bit_vooddc_setscl, | |
| .getsda = bit_vooddc_getsda, | |
| .getscl = bit_vooddc_getscl, | |
| .udelay = CYCLE_DELAY, | |
| .timeout = TIMEOUT | |
| }; | |
| static struct i2c_adapter voodoo3_ddc_adapter = { | |
| .owner = THIS_MODULE, | |
| .class = I2C_CLASS_DDC, | |
| .name = "DDC Voodoo3/Banshee adapter", | |
| .algo_data = &voo_ddc_bit_data, | |
| }; | |
| static struct pci_device_id voodoo3_ids[] __devinitdata = { | |
| { PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_VOODOO3) }, | |
| { PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_BANSHEE) }, | |
| { 0, } | |
| }; | |
| MODULE_DEVICE_TABLE (pci, voodoo3_ids); | |
| static int __devinit voodoo3_probe(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| int retval; | |
| retval = config_v3(dev); | |
| if (retval) | |
| return retval; | |
| /* set up the sysfs linkage to our parent device */ | |
| voodoo3_i2c_adapter.dev.parent = &dev->dev; | |
| voodoo3_ddc_adapter.dev.parent = &dev->dev; | |
| retval = i2c_bit_add_bus(&voodoo3_i2c_adapter); | |
| if (retval) | |
| return retval; | |
| retval = i2c_bit_add_bus(&voodoo3_ddc_adapter); | |
| if (retval) | |
| i2c_bit_del_bus(&voodoo3_i2c_adapter); | |
| return retval; | |
| } | |
| static void __devexit voodoo3_remove(struct pci_dev *dev) | |
| { | |
| i2c_bit_del_bus(&voodoo3_i2c_adapter); | |
| i2c_bit_del_bus(&voodoo3_ddc_adapter); | |
| iounmap(ioaddr); | |
| } | |
| static struct pci_driver voodoo3_driver = { | |
| .name = "voodoo3_smbus", | |
| .id_table = voodoo3_ids, | |
| .probe = voodoo3_probe, | |
| .remove = __devexit_p(voodoo3_remove), | |
| }; | |
| static int __init i2c_voodoo3_init(void) | |
| { | |
| return pci_register_driver(&voodoo3_driver); | |
| } | |
| static void __exit i2c_voodoo3_exit(void) | |
| { | |
| pci_unregister_driver(&voodoo3_driver); | |
| } | |
| MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>, " | |
| "Philip Edelbrock <phil@netroedge.com>, " | |
| "Ralph Metzler <rjkm@thp.uni-koeln.de>, " | |
| "and Mark D. Studebaker <mdsxyz123@yahoo.com>"); | |
| MODULE_DESCRIPTION("Voodoo3 I2C/SMBus driver"); | |
| MODULE_LICENSE("GPL"); | |
| module_init(i2c_voodoo3_init); | |
| module_exit(i2c_voodoo3_exit); |